Abstract
Electrode-embedded nanopore is considered as a promising device structure for label-free single-molecule sequencing, the principle of which is based on nucleotide identification via transverse electron tunnelling current flowing through a DNA translocating through the pore. Yet, fabrication of a molecular-scale electrode-nanopore detector has been a formidable task that requires atomic-level alignment of a few nanometer sized pore and an electrode gap. Here, we report single-molecule detection using a nucleotide-sized sensing electrode embedded in-plane nanopore. We developed a self-alignment technique to form a nanopore-nanoelectrode solid-state device consisting of a sub-nanometer scale electrode gap in a 15 nm-sized SiO2 pore. We demonstrate single-molecule counting of nucleotide-sized metal-encapsulated fullerenes in a liquid using the electrode-integrated nanopore sensor. We also performed electrical identification of nucleobases in a DNA oligomer, thereby suggesting the potential use of this synthetic electrode-in-nanopore as a platform for electrical DNA sequencing.
Similar content being viewed by others
Introduction
A molecular-sized pore in a membrane provides a platform for studying dynamics and structure of polynucleotides in a liquid with single-molecule sensitivity.1,2,3 The sensing mechanism involves detections of ionic current blockade during translocation of an individual molecule through a pore. Considerable efforts have been devoted to apply this nanopore sensor for label-free genome sequencing1,2,3,4,5,6 since the first demonstration of single DNA molecule detection using an α-haemolysin channel.7 Recent experiments by Clark et al.5 adopted an adapter molecule to engineer a protein channel, which contributed to slow down molecular translocation and thereby allowed discriminations of single nucleotides by ionic current.5 A graphene nanopore has also attracted much attention because of the well-defined single atomic sheet geometry ideal for DNA sequence detection in conjunction with the excellent mechanical properties.8 It remains a challenge, however, to realize single-molecule sequencing by the ionic current blockade method.2,3
There is thus growing interest in incorporating additional probes to nanopore sensors.9,10,11 Recent break junction experiments have demonstrated that tunnelling current can serve as a sensitive probe for identifying nucleotides of a single-molecule DNA in liquid environment.12,13 Combining this capability, an electrode-embedded nanopore was proposed to be a promising device design for DNA sequencing via transverse electron transport; the device concept is based on electrical identification of nucleotides using the tunnelling current sensing electrodes while a DNA translocates through the pore.2,3,14
Despite the huge potential, construction of DNA-sized electrode-embedded nanopore structures has been hindered by the technical difficulty of adjusting positions of a pore and an electrode gap with sub-nanometer precision.15,16 Therefore, we developed a self-alignment technique to form a molecular-scale nanoelectrode-nanopore system. Our approach is based on electromigration-induced breaking of a SiO2/Au/SiO2 multilayer structure defined on a silicon wafer (Fig. 1a). As current flows only through Au, the SiO2 layers are expected to remain intact during the electrical breakdown. In this way, virtually perfect alignment of an electrode gap and a pore can be achieved.
Results
Electrode-embedded nanopore structure was formed by first electrically thinning a 15 nm thick Au nano-junction sandwiched between SiO2 layers in a vacuum by applying bias sweeps cyclically under an automated resistance feed-back control to induce electromigration at the narrowest constriction until the resistance became larger than 1000 Ω (see Supplementary Fig. S1 and S2). Subsequently, we let the contact break spontaneously at Vb = 0.1 V and formed a sub-nanometer electrode gap (Fig. 1b and 1c, see also Methods).17,18 Scanning electron microscope was implemented at various electron beam acceleration voltage conditions Eacc to characterize the SiO2 cover layer after the electrical junction breaking (see Supplementary Fig. S3 and S4). A flat topology instead of an electrode gap was imaged at Eacc = 0.5 kV,19 thereby validating that SiO2 overlayer indeed remained undamaged and that the nanopore-with-transverse-electrode structure consisting of a sub-nanometer electrode gap with a 15 nm sized pore has been formed.
The nanogap-nanopore formation mechanism can be inferred from the electron micrographs. In the active electromigration breaking processes, concentrated Joule heating at the high-resistance constriction increases the mobility of Au atoms there and induces an atomic flux along a direction of electron flow by wind force.20 In case when the SiO2 top layer is absent, migration occurs in three dimension yielding a hillock on the current downstream side of electrode gaps (Fig. 1d and 1f). Situation is different for SiO2/Au/SiO2 junctions. It is known that the weak binding energy of 0.1 eV for Au with SiO2 and the large atomic size of Au give rise to a high barrier that impedes Au atoms for migrating vertically into SiO2. The critical temperature for Au-SiO2 migration is roughly defined by the eutectic point of the Au-Si system, which is about 640 K.21 Since the junction temperature cannot be this high during the electromigration processes (although somewhat dependent on the geometry of junctions, electromigration is usually triggered at a temperature around 400 K to 450 K),20,22 the vertical migration of Au atoms is unlikely to take place. The SiO2 layer thus effectively impedes Au atomic migration in a cross-plane direction. Consequently, electromigration thinning proceeds via extrusion at side surface of Au contact (Fig. 1c and 1e).
Similarly, it is worth noting that migration of Cr into a Au thin film occurs at a relatively low temperature around 400 K.23 Joule heating during electromigration breakdown process may thus induce vertical migration of thermally exited Cr atoms into Au, which would lead to a change in impedance of the junction and concomitant error in the feed-back control of the electrical junction breaking. Nevertheless, Cr layer is only 1 to 2 nm thick, very thin compared to the thickness of Au junctions (15 nm thick). Hence, it is anticipated that the alloying effects of the small amount of Cr in Au on the electrical properties of the junction poses only marginal influence on the nanopore formation process.
Having established a self-alignment method to fabricate molecular-sized electrode-embedded in-plane nanopore structure, we assessed the device potential as a single-molecule detector by conducting electrical detection of fullerenes in a liquid environment. For this purpose, we prepared a fluidic channel of PDMS on the substrate (Fig. 2a and 2b; see also Methods and Supplementary Fig. S5). Micro-pillars were also built around the multi-layer junction that served as spacer for the PDMS (Fig. 2c and 2d). Here, we employed Er@C82 as a target. This molecule is chosen to mimic a transverse tunnelling current detection of DNA; diameter of Er@C82 is about 0.8 nm close to that of nucleotides.24
After forming an electrode-nanopore system by the aforementioned self-alignment scheme, we injected a dilute chlorobenzene solution of Er@C82 (1μM) into the fluidic channel and carried out current measurements at Vb = 0.1 V using the sensing electrodes. As a result, we observed a jump of the current I that indicates trapping of single metal-encapsulated C82 molecule by a strong fullerene-Au van der Waals interaction with a binding energy of about 1 eV (Fig. 2e inset).25,26 Following the molecular trap, current tended to fluctuate substantially until dropping to zero (Fig. 2e). The I-fluctuation is attributable to Brownian motion of the fullerene molecule tightly bound to Au electrodes, whereas the current drop to zero indicates molecular detrapping from the electrode gap. A histogram constructed with the I-t curve revealed a pronounced peak at I1 ∼ 35 nA and broad peaks at I2 ∼ 66 nA and I3 ∼ 116 nA (Fig. 2f). These peaks are naturally ascribed to electron transport through one, two and three fullerene molecules anchored to Au electrodes in parallel from the fact that approximately Ii = 35 × i nA (i = 1, 2, 3 ···).27 Relatively narrow distributions of I reflects the spherical morphology of Er@C82 that provides conformation-independent electronic coupling to Au electrodes.28 This well-defined single molecule conductance enabled the electrical single-molecule counting of Er-encapsulated C82 in the organic solvent.
The above results ensure that the size of an electrode gap in the in-plane nanopore is about 0.8 nm, small enough for detecting single-nucleotides by tunnelling current. We therefore utilized the nanoelectrode-nanopore structure for electrical identification of nucleotides in a DNA oligomer (Fig. 3a and 3b). Figure 3c displays a I-t trace measured at Vb = 0.75 V in a Milli-Q solution of guanosine-5′-monophosphates (GMP). We detected spike-like signals representing single-GMP trapping/detrapping events in the electrode gap (Fig. 3d).12,29 A histogram is constructed by extracting the height of current spikes Ip for 1000 signals (Fig. 3e). The characteristic single-molecule conductance GGMP deduced from a peak position of the log10(Ip) distribution is GGMP ∼ 111 pS, which is in good accordance with GGMP ∼ 130 pS reported in previous break junction experiments.12
The single-molecule analysis was extended to DNA oligomers. In case of 6-mer oligonucleotides (TTTGGG, 1μM in Milli-Q, Vb = 0.75 V), I-t traces frequently demonstrated two-level steps (Fig. 3f). Correspondingly, Ip histogram manifests a bimodal distribution (Fig. 3g). These peaks are located at Ilow ∼ 40 pA (53 pS) and Ihigh ∼ 79 pA (105 pS). The latter profile corresponds to that of GMP. Thus, Ilow and Ihigh can be assigned to the conductance states of thymine and guanine in the oligomer, respectively.12 It is noticeable that the thymine peak is much smaller than that of guanine in spite of the fact that the oligonucleotides possess equal amount of T and G in the sequence. This discrepancy stems from the definition of Ip that tends to overestimate the counts of high-conductance nucleotides in DNA oligomers; Ip is prone to be that of the nucleotides with higher conductivity for the case of multi-level signals. Nonetheless, in this way, the in-plane nanopore detector can potentially be exploited for identifying nucleobases in oligonucleotides.
As long-read is of a major concern in DNA sequencer, we further attempted electrical identification of longer oligonucleotides with 22-base sequence. The acquired I-t traces (1μM in Milli-Q, Vb = 0.75 V) showed current spikes (Fig. 4a and 4b). These signals had similar amplitudes in a range from 20 pA to 500 pA. On the other hand, the dwell time td was longer compared to the shorter oligonucleotide counterparts as manifested in Fig. 4c.
Discussion
The monotonic shift of td distributions with increasing the length of DNA oligomers is ascribed a priori to a difference in time necessary for a DNA to flow through an electrode gaps. When this is the case, td of n-base oligonucleotides should scale as td = tm × n, where tm is the trapping duration of the monomer. On the other hand, the characteristic td estimated by Gaussian fitting is 13 ms, 27 ms and 91 ms for monomer, 6-mer and 22-mer nucleotides, respectively. This implies that in most of the cases only about 30 % of the entire length of the oligonucleotides could pass through the electrode gap. Furthermore, peculiar I-spikes with extraordinarily long td (> 100 s) and high Ip (> 5 nA) were found for 22-mer nucleotides (Fig. 4d). Similar high-current signals were observed in recent tunnelling current measurements of λ-DNA.16 The anomalous feature most likely arises from longitudinal electron transport through a long DNA connected to two Au electrodes (Fig. 4d, inset). These issues can be resolved technically by introducing the electrophoretic method and making the pore size smaller by reducing the thickness of Au junction to confine and regulate a DNA flow through the electrode gap. The electrode-embedded in-plane nanopore single-molecule detector offers the prospect of label-free electrical DNA sequencing.
Methods
Fabrication of SiO2/Au/SiO2 junctions
Micro-electrodes were formed on a 300 nm thick SiO2 insulating layer on a phosphor-doped Si substrate using a photolithography method with subsequent deposition of Cr/Au (1 nm/30 nm) by the radio-frequency (RF) magnetron sputtering and lift-off processes. After that, a nano-scale junction and micro-pillar array were patterned using an electron-beam lithography technique. Then, Au/SiO2 (15 nm/150 nm) layer was deposited by the RF sputtering, followed by lift-off to form a Au/SiO2 junction with a bow-tie geometry and square-shaped pillars. Finally, the sample was exposed to isotropic reactive ion etching using CF4 and O2 mixture gas to form a SiO2 (75 nm)/Au (15 nm)/SiO2 (75 nm) junction.
Electromigration breaking
Bias sweep was applied to the SiO2/Au/SiO2 junction under a resistance feed-back control using Keithley 6487 picoammeter/voltage source in a vacuum better than 10−5 Torr. Specifically, a dc voltage Vb imposed to the multilayered junction was increased linearly from 0.2 V at a rate of 400 mV/s. When Vb becomes higher than 1 V, this rate was decrease to 100 mV/s to prevent overcurrent junction breakdown. The junction resistance R tended to increase at high-field by concentrated Joule heating and associated thermally-activated electromigration at its narrowest constriction region. After the resistance increased by 0.4 % from that at Vb = 0.2 V, Vb was quickly lowered to 0.2 V. The junction could be thinned gradually to atomic scale by repeating these automated processes until R became larger than 1000 Ω. The active electromigration-induced thinning process was then halted and the metastable atom-sized contact was broken by thermal fluctuations at a low constant bias voltage of Vb = 0.1 V. At this stage, we observed the conductance G to drop in a stepwise manner, indicative of thermally-activated breakdown of Au atom-sized contact (Fig. 1b, see also Supplementary Fig. S1 and S2). Right before the eventual breakdown, a long plateau was often observed at G ∼ 1 G0 (G0 = 2e2/h ∼ 77.5 μS is the conductance quantum), which signifies that Au junction has been narrowed to one atom size wherein one fully transparent channel exists for electron transmission.30 What followed was structure relaxation after self-breaking of Au single-atom contacts and accompanied formation of a sub-nanometer electrode gap. Only when an electrode gap was formed in this way did we detected the characteristic current spikes in molecular solution; I-t curves were totally featureless when overcurrent breakdown occurred during the electrical breaking processes that results in large electrode gaps (see Supplementary Fig. S6).
PDMS channel
An SU-8 mold with a micro-channel pattern was formed on a SiO2/Si wafer by a photolithography procedure. Subsequently, the PDMS (Sylgard 184) was cured on the mold in an oven at 70 degrees Celsius. The PDMS replica was then cut and peeled off from the mold. The thus prepared PDMS channel was bonded on the sample substrate onto which a SiO2/Au/SiO2 junction and micro-pillars were formed by pretreating the both surfaces with oxygen plasma and UV light for better adhesion and enhanced hydrophilic properties.
Tunnelling current measurements
After forming an electrode-embedded nanopore structure by the electromigration/self breaking technique in a vacuum, Argon gas was admitted to the sample chamber and a dilute solution of a target molecule current was injected into the PDMS channel. The nucleotide molecules were synthesized by FASMAC Co., Ltd. Er-encapsulated C82 molecules were synthesized using the scheme reported elsewhere.21 Chrolobenzene was purchased from Sigma-Aldrich Co., Ltd. Electrical current flowing through the two Au nanoelectrodes was then recorded at a sampling rate of 10 kHz with a home-built current preamplifier and a National Instruments PXI-5922 digitizer under a constant dc bias voltage Vb. The amplifier is a logarithmic current-to-voltage converter with a linear transfer characteristics below 1 nA and a bandwidth of 100 kHz, whose basic structure is composed of a sensing resistor and series of four diodes.31 The current measurements were carried out not more than consecutive 2 hours to avoid possible contamination effects.
References
Branton, D. et al. The potential and challenges of nanopore sequencing. Nat. Biotech. 26, 1146–1153 (2008).
Zwolak, M. & Di Ventra, M. Colloquim: Physical approaches to DNA sequencing and detection. Rev. Mod. Phys. 80, 141–165 (2008).
Dekker, C. Solid-state nanopores. Nat. Nanotechnol. 2, 209–215 (2007).
Hall, A. R., Scott, A., Rotem, D., Mehta, K. K., Bayley, H. & Dekker, C. Hybrid pore formation by directed insertion of α-haemolysin into solid-state nanopores. Nat. Nanotechnol. 5, 874–877 (2010).
Clarke, J., Wu, H.-C., Jayasinghe, L., Patel, A., Reid, S. & Bayley, H. Continuous base identification for single-molecule nanopore DNA sequencing. Nat. Nanotechnol. 4, 265–270 (2009).
Derrington, I. M. et al. Nanopore DNA sequencing with MspA. Proc. Nat. Acad. Sci. 107, 16060–16065 (2010).
Kasianowicz, J. J., Brandin, E., Branton, D. & Deamer, D. W. Characterization of individual polynucleotide molecules using a membrane channel. Proc. Nat. Acad. Sci. 93, 13770–13773 (1996).
Garaj, S., Hubbard, W., Reina, A., Kong, J., Branton, D. & Golovchenko, J. A. Graphene as a subnanometre trans-electrode membrane. Nature 467, 190–193 (2010).
Keyser, U. F. et al. Direct force measurements on DNA in a solid-state nanopore. Nat. Phys. 2, 473–477 (2006).
McNally, B., Singer, A., Yu, Z., Sun, Y., Weng, Z. & Meller, A. Optical recognition of converted DNA nucleotides for single-molecule sequencing using nanopore arrays. Nano Lett. 10, 2237–2244 (2010).
Liang, X. & Chou, S. Y. Nanogap detector inside nanofluidic channel for real-time lavel-free DNA analysis. Nano Lett. 8, 1472–1476 (2008).
Tsutsui, M., Taniguchi, M., Yokota, K. & Kawai, T. Identifying single nucleotides by tunnelling current. Nat. Nanotechnol. 5, 286–290 (2010).
Huang, S. et al. Identifying single bases in a DNA oligomer with electron tunnelling. Nat. Nanotechnol. 5, 868–873 (2010).
Lagerqvist, J., Zwolak, M. & Di Ventra, M. Fast DNA sequencing via transverse electronic transport. Nano Lett. 6, 779–782 (2006).
Taniguchi, M., Tsutsui, M., Yokota, K. & Kawai, T. Fabrication of the gating nanopore device. Appl. Phys. Lett. 95, 123701 (2009).
Ivanov, A. P. et al. DNA tunneling detector embedded in a nanopore. Nano Lett. 11, 279–285 (2011).
O'Neill, K., Osorio, E. A. & van der Zant, H. S. J. Self-breaking in planar few-atom Au Constrictions for nanometer-spaced electrodes. Appl. Phys. Lett. 90, 133109 (2007).
Tsutsui, M., Taniguchi, M. & Kawai, T. Fabrication of 0.5 nm electrode gaps using self-breaking technique. Appl. Phys. Lett. 93, 163115 (2008).
Kanaya, K. & Okayama, S. Penetration and energy-loss theory of electrons in solid targets. J. Phys. D: Appl. Phys. 5, 43 (1972).
Trouwborst, M. L., van der Molen, S. J. & van Wees, B. J. The role of Joule heating in the formation of nanogaps by electromigration. J. Appl. Phys. 99, 114316 (2006).
Madams, C. J., Morgan, D. V. & Howes, M. J. Migration of gold atoms through thin silicon oxide films. J. Appl. Phys. 45, 5088–5090 (1974).
Taychatanapat, T., Bolotin, K. I., Kuemmeth, F. & Ralph, D. C. Imaging electromigration during the formation of break junctions. Nano Lett. 7, 652–656 (2007).
Hirvonen, J. K., Weisenberger, W. H., Westmoreland, J. E. & Meussner, R. A. Backscattering investigation of low-tempearture migration of chromium through gold films. Appl. Phys. Lett. 21, 37–39 (1972).
Shinohara, H. Endohedral metallofullerenes. Rep. Prog. Phys. 63, 843–892 (2000).
Chavy, C., Joachim, C. & Altibelli, A. Interpretation of STM images: C60 on the gold (110) surface. Chem. Phys. Lett. 214, 567 (1993).
Park, H., Park, J., Lim, A. K. L., Anderson, E. H., Alivisatos, A. P. & McEuen, P. L. Nano-mechanical oscillations in a single-C60 transistor. Nature 407, 57–60 (2000).
Xu, B. & Tao, N. J. Measurement of single-molecule resistance by repeated formation of molecular junctions. Science 301, 1221 (2003).
Martin, C. A., Ding, D., Sørensen, J. K., Bjørnholm, T., van Ruitenbeek, J. M. & van der Zant, H. S. J. Fullerene-based anchoring groups for molecular electronics. J. Am. Chem. Soc. 130, 13198–13199 (2008).
Chang, S. et al. Electronic signatures of all four DNA nucleosides in a tunneling gap. Nano Lett. 10, 1070–1075 (2010).
Agraït, N., Yeyati, A. L. & van Ruitenbeek, J. M. Quantum properties of atomic-sized conductors. Phys. Rep. 377, 81–279 (2003).
Dürig, U., Novotny, L. & Michel, B. Logarithmic current-to-voltage converter for local probe microscopy. Rev. Sci. Instrum. 68, 3814–3816 (1997).
Acknowledgements
This work was supported by the Japan Society for the Promotion of Science (JSPS) through its “Funding Program for World-Leading Innovative R&D on Science and Technology”.
Author information
Authors and Affiliations
Contributions
M. Tsutsui, M. Taniguchi and T. K. planned and designed experiments. M. Tsutsui and R. S. fabricated in-plane nanopore devices. M. Tsutsui and M. Taniguchi exhibited single-molecule conductance measurements. Y. I. and T. O. synthesized metal-encapsulated fullerenes. M. Tsutsui and M. Taniguchi performed data analyses. M. Tsutsui, M. Taniguchi and T. K. co-wrote paper.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Electronic supplementary material
Supplementary Information
Supplementary Information
Rights and permissions
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareALike 3.0 Unported License. To view a copy of this license, visit http://creativecommons.org/licenses/by-nc-sa/3.0/
About this article
Cite this article
Tsutsui, M., Rahong, S., Iizumi, Y. et al. Single-molecule sensing electrode embedded in-plane nanopore. Sci Rep 1, 46 (2011). https://doi.org/10.1038/srep00046
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep00046
This article is cited by
-
Localised solid-state nanopore fabrication via controlled breakdown using on-chip electrodes
Nano Research (2022)
-
DNA sequencing: an overview of solid-state and biological nanopore-based methods
Biophysical Reviews (2022)
-
Solid-state nanopore systems: from materials to applications
NPG Asia Materials (2021)
-
Synchronized resistive-pulse analysis with flow visualization for single micro- and nanoscale objects driven by optical vortex in double orifice
Scientific Reports (2021)
-
Tunable Ultra-high Aspect Ratio Nanorod Architectures grown on Porous Substrate via Electromigration
Scientific Reports (2016)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.