Abstract
Waveguide-coupled silicon ring or disk resonators have been used for optical signal processing and sensing. Large-scale integration of optical devices demands continuous reduction in their footprints, and ultimately they need to be replaced by silicon-based plasmonic resonators. However, few waveguide-coupled silicon-based plasmonic resonators have been realized until now. Moreover, fluid cannot interact effectively with them since their resonance modes are strongly confined in solid regions. To solve this problem, this paper reports realized plasmofluidic disk resonators (PDRs). The PDR consists of a submicrometer radius silicon disk and metal laterally surrounding the disk with a 30-nm-wide channel in between. The channel is filled with fluid, and the resonance mode of the PDR is strongly confined in the fluid. The PDR coupled to a metal-insulator-silicon-insulator-metal waveguide is implemented by using standard complementary metal oxide semiconductor technology. If the refractive index of the fluid increases by 0.141, the transmission spectrum of the waveguide coupled to the PDR of radius 0.9 μm red-shifts by 30 nm. The PDR can be used as a refractive index sensor requiring a very small amount of analyte. Plus, the PDR filled with liquid crystal may be an ultracompact intensity modulator which is effectively controlled by small driving voltage.
Similar content being viewed by others
Introduction
Silicon photonic resonators are usually integrated-optical rings or disks in which light circulates to be stored at specific wavelengths. They are playing key roles in silicon photonics as modulators, switches, and filters1,2,3. In addition, they have attracted a lot of attention as compact sensors4,5,6. Nowadays, there is a strong demand that the footprints of silicon photonic resonators need to be reduced in order to increase the integration density of a silicon photonic integrated-circuit. Small ring or disk resonators have additional advantages such as a large free spectral range and use of a small amount of analyte in sensing application. Moreover, it is possible to achieve a large value of the Purcell factor Fp, which leads to development of novel devices such as a single photon source7.
To satisfy the demand, there have been many researches on small silicon photonic resonators8,9,10. However, it is well known that silicon photonic resonators cannot be made small below the diffraction limit. Therefore, ultimate reduction of the effective mode volume (Veff) of a resonator may be obtained by switching from silicon photonic resonators to plasmonic resonators which support resonance modes with the nature of a surface plasmon polariton. A variety of individually addressable plasmonic resonators have been theoretically studied11,12,13,14,15, but just a few of them, especially silicon-based hybrid plasmonic ring or disk resonators, have been realized and characterized16,17,18. Silicon-based hybrid plasmonic ring or disk resonators support resonance modes which have electric field highly enhanced in the narrow region, with a low refractive index, between metal and silicon. They are prominent since they possess moderate values of the Q factor and small values of Veff. In addition, they are compatible with standard complementary metal oxide semiconductor (CMOS) technology such that seamless integration between them and silicon photonic devices is easy.
In this paper, plasmofluidic disk resonators (PDRs), which are silicon-based hybrid plasmonic disk resonators, are investigated. The PDR has a silicon disk laterally surrounded by metal with a narrow channel in between. The narrow channel is filled with fluid, and the resonance modes of the PDR are substantially confined in the fluid. The key feature of the PDR is that replacement of one fluid with another can reconfigure its resonance characteristics. This can be exploited to implement microfluidically controllable plasmonic devices and sensors requiring an extremely small volume of analyte, to name a few. This paper, first, explains the calculated characteristics of the isolated PDRs. Then, the PDRs side-coupled to metal-insulator-silicon-insulator-metal (MISIM) waveguides19,20,21,22 are fabricated by using standard CMOS technology and characterized. Their measured characteristics are compared with calculated ones. Finally, possible improvement and application of the PDR coupled to the MISIM waveguide are dicussed.
Results
Theoretical analysis of the isolated PDR
The isolated PDR is schematically shown in Fig. 1(a). The silicon (Si) disk is 250 nm thick, and its radius is rD. The metal of the resonator is copper (Cu) of thickness 260 nm, and it is recessed 30 nm below the bottom of the Si disk. The circular channel between the Si disk and the metal is 30 nm wide. The PDR is covered by fluid of refractive index nl. The parameter values used for the isolated PDR come from those of the realized PDR coupled to the MISIM waveguide. The PDR was analyzed by using the finite difference time domain (FDTD) method (See Methods). rD was appropriately adjusted such that a resonance mode exists at the free-space wavelength λ around 1550 nm. The resonance mode has a field distribution in which the major component of its electric field E is in the radial direction. For rD = 0.9 μm and nl = 1.45, the distribution of |E|2 at λ = 1558 nm in the plane at z = 125 nm is shown in Fig. 1(b). The electric field is highly enhanced in the channel. This is also confirmed from the distribution of the radial component of the electric field, Er as shown in Fig. 1(c). Half the number of nodes in the azimuthal direction in Fig. 1(b) corresponds to the azimuthal order of the resonance mode, m. When rD ≤ 1.4 μm, all the resonance modes in the wavelength range between 1400 and 1700 nm have similar field distributions in the azimuthal plane, i.e. there is no resonance mode of higher radial-order or higher vertical-order.
The calculated relation between the intrinsic Q factor of the PDR, Qi and rD for nl = 1.45 is shown in Fig. 2(a). If rD ≤ 0.89 μm, Qi increases with rD. For rD > 0.89 μm, Qi seems to saturate at ~350. Qi satisfies the following relation: 1/Qi = 1/Qr+1/Qo, where Qr and Qo are the Q factors determined by the radiation and Ohmic losses of the PDR. Qr is obtained by analyzing the PDR with the imaginary part of the dielectric constant of Cu set to 0. As shown in the inset of Fig. 2(a), Qr increases almost exponentially with rD. As rD decreases, Qo decreases since the field distribution in the PDR is further shifted outwards, especially toward the metal, for a smaller value of rD such that the Ohmic loss due to the absorption by the metal increases. For rD > 0.89 μm, Qi is limited by the Ohmic loss, and Qi ≈ Qo. In the case of a curved MISIM waveguide, its propagation loss was shown to approach that of a straight MISIM waveguide as the radius of curvature of the bend increases22. Similarly, the attenuation coefficient αD of the resonance mode in the azimuthal direction approaches some value such that the saturation of Qi which is inversely proportional to αD exists. For comparison, a 250-nm-thick Si disk embedded in the fluid of refractive index nl was also analyzed, and the dependence of its intrinsic Q factor on rD is also shown in Fig. 2(a). For rD < 0.92 μm, the PDR possesses a larger intrinsic Q factor than the Si disk resonator. The effective mode volume Veff and Purcell factor Fp of the resonance mode were calculated (See Methods). The calculated values of Veff and Fp are shown with respect to rD in Fig. 2(b). Both the intrinsic Q factor and effective mode volume of the PDR are smaller than those of previous Si-based hybrid plasmonic disk resonators11,18, which are vertical stacks of metal, oxide, and Si disks. In consequence, the Purcell factor of the PDR is similar to those of the previous Si-based hybrid plasmonic disk resonators.
Investigation of the PDR coupled to the MISIM waveguide
The PDR side-coupled to the MISIM waveguide is schematically shown in Fig. 3(a). The MISIM waveguide consists of the 250-nm-high Si strip of width wS and the 260-nm-thick Cu patterns sandwiching the Si strip with the 30-nm-wide channels in between. These channels are also filled with the fluid, and the fluid is the insulator of the MISIM waveguide. There is a sort of aperture-assisted coupling23 between the PDR and the MISIM waveguide. The Si pattern of the aperture has a width wa and a length la. The MISIM waveguide is coupled to Si photonic waveguides with a 450-nm-wide Si core via 600-nm-long tapering regions. Each Si photonic waveguide is coupled to another silicon photonic waveguide with a 5-μm-wide Si core via a 200-μm-long tapering region. A scanning electron microscope image of the fabricated device is shown in Fig. 3(b). The length of the MISIM waveguide is 2 μm, and wS, wa, and la are about 190 nm, 1.0 μm, and 0.23 μm, respectively.
The channels were filled with an index oil with nl = 1.44. The as-measured transmission spectrum of the MISIM waveguide coupled to the PDR with rD = 0.9 μm is shown in Fig. 4(a). Because of the Fabry-Perot resonance between the facets of the input and output 5-μm-wide Si waveguides, which are about 15 mm apart, there are rapid fluctuations. To remove the influence of the Fabry-Perot resonance, the as-measured transmission spectrum was smoothed by using the adjacent averaging method (See Supplementary Information S1), and the smoothed transmission spectrum is also shown in Fig. 4(a). Then, the theoretical spectrum of a simple resonator-coupled waveguide, which is expressed by
was fitted to the smoothed transmission spectrum (See Supplementary Information S2). In Eq. (1), βD and αD are the propagation constant and attenuation coefficient of the resonance mode in the azimuthal direction; aC is related to the fractional loss of the coupling between the PDR and the MISIM waveguide, which is ; τ exp(iθ) is the straight-through coupling coefficient of the coupling. The fitted curve is also shown in Fig. 4(a). The loaded Q factor of the PDR is 24.6, and the value of Qi of the realized PDR, which is determined from the fitting process, is 57 (See Methods). According to Eq. (1), the PDR is critically coupled to the MISIM waveguide (i.e., T = 0) if τ = aC exp(−2παDrD). The fitted values of τ, aC, and αD are 0.7888, 0.9299, and 9.908 × 10−2 μm−1, respectively, and τ > aC exp(−2παDrD) for these values. Therefore, the PDR seems to be under-coupled to the MISIM waveguide. The value of Qi is about 5.6 times smaller than that of the ideal PDR, which is shown in Fig. 2(a). The etching of silicon dioxide (SiO2) in the fabrication process (See Methods) seems to induce roughness on the rim of the Si disk. Because of this roughness, the attenuation coefficient αD of the resonance mode in the azimuthal direction increases, and Qi decreases. The decrease of Qi accords with the increase of the propagation loss of the MISIM waveguide. The propagation loss is 0.30 dB/μm prior to the etching of SiO2 and it increases to 0.46 dB/μm after the etching and filling the channels with the fluid24. The measured transmission spectra of the MISIM waveguides coupled to the PDRs with different values of rD are shown in Fig. 4(b,c) and compared with those calculated by using the FDTD method. As deduced from the resonance condition of the PDR, the transmission spectrum shifts toward a longer wavelength for a larger value of rD. The calculation results reveal that the transmission spectra in Fig. 4(b) are associated with the resonance mode of order 8 and those in Fig. 4(c) are associated with the resonance mode of order 9.
The transmission spectrum of the MISIM waveguide coupled to the PDR with rD = 0.9 μm was measured while the channels were filled with different index oils. The measured transmission spectra are shown in Fig. 5(a) for different values of nl. As nl increases, the transmission spectrum further red-shifts. The shift of the transmission spectrum depending on nl is in good agreement with the calculated one shown in Fig. 5(b). The measured and calculated relations of the resonance wavelength λm (i.e., the center wavelength of the transmission spectrum) to nl are shown in Fig. 5(c). The slope of the straight line fitted to the measured relation is 214 nm/RIU (RIU is the acronym of refractive index unit), which is about 70% of the calculated slope. The difference between the measured and calculated slopes may be caused by the partially filled channels. To check this, the PDR-coupled MISIM waveguide with air gaps of height h at the bottom of the channels (See the inset of Fig. 5(d)) was simulated for a few values of h and nl = 1.390, 1.440, 1.486, and 1.531. For a fixed value of nl, λm decreases and the minimum transmission at λm increases as h increases (See Supplementary Information S3). In addition, such changes become more considerable for a larger value of nl. This happens since the coupling between the MISIM waveguide and the PDR is affected by the air gaps. From the relation of λm to nl, the sensitivity for a value of h was calculated. The relation of the sensitivity to h is shown in Fig. 5(d). As h increases, the sensitivity decreases. The value of h at which the sensitivity is the same as the experimental value is estimated to be 64 nm. The air gaps may exist since a drop of the index oil was applied to the surface of the PDR-coupled MISIM waveguide and the index oil filled the channels downwards from the surface. If the channels are sealed by bonding appropriate polymer like poly(methyl methacrylate) (PMMA)25, they may be filled by capillary flow26 or electrokinetic flow27,28,29 without the air gaps.
If the PDR coupled to the MISIM waveguide is considered as a refractive index sensor, the slope corresponds to the sensitivity of the sensor. The sensitivity of the PDR is more than two times larger than those of Si disk resonators6. However, the measures of evaluating a refractive index sensor are not only the sensitivity but also the linewidth of the transmission spectrum of the sensor. The figure of merit for refractive index sensors is the ratio of the sensitivity to the linewidth. The figure of merit of a large Si disk resonator is much larger than that of the PDR. However, Qi of a Si disk resonator becomes smaller than Qi of the PDR when rD is smaller than 0.92 μm as shown in Fig. 2(a). This means that the linewidth, which is inversely proportional to Qi, of the PDR becomes smaller than that of a Si disk resonator. Therefore, in a situation that requires a compact refractive index sensor in need of a small amount of analyte, the figure of merit of the PDR becomes larger than that of a Si disk resonator if rD ≤ 0.92 μm. Although the figure of merit of the realized PDR is about 3.3, it may reach up to 9.7 if the fabrication-induced loss is reduced to zero and the PDR is critically coupled to the MISIM waveguide as discussed below. Despite the modest figure of merit, the PDR is attractive as a sensor since it requires an extremely small volume of analyte, which ultimately approaches the volume of the channel. The volume of the channel is estimated to be 44.8 attoliters if the channel is completely filled without an air gap.
Improvement and application of the PDR coupled to the MISIM waveguide
The PDR-coupled MISIM waveguide needs to be improved such that the resonance band in its transmission spectrum becomes deeper and narrower. For this purpose, the aperture-assisted coupling between the PDR and the MISIM waveguide needs to be controlled by adjusting the width (wa) and length (la) of the aperture region. FDTD simulation shows that wa more influences on the coupling than la(See Supplementary Information S4). However, when wS = 190 nm, the PDR with rD = 0.9 μm cannot be critically coupled to the MISIM waveguide regardless of wa. If wS is reduced to 50 nm, the PDR is almost critically coupled to the MISIM waveguide as checked from Fig. 6, which shows the transmission spectra of the PDR-coupled MISIM waveguide with wS = 50 nm for various values of wa and la. For wa = 320 nm and la = 100 nm, the minimum transmission at the resonance wavelength is −25.5 dB, the linewidth of the transmission spectrum is 22 nm, and the loaded Q factor of the PDR is 71.2.
The PDR or the PDR-coupled MISIM waveguide belongs to plasmofluidics which is emerging as an attractive field with synergetic advantages of plasmonics and micro- or nano-fluidics. Recently, there have been two review papers focusing on plasmofluidics30,31. Diverse applications of plasmofluidics are explained there, and one example of the applications is plasmonic sensing32 such as the aforementioned refractive index sensor based on the PDR. Another application is reconfiguration of plasmonic devices by means of liquid crystal (LC)31. With regard to this point, the PDR-coupled MISIM waveguide can be used as an ultracompact intensity modulator based on LC. When well-known LC E7 is used as fluid, it is anticipated that the transmission of the PDR-coupled MISIM waveguide can be tuned by about 17 dB with a driving signal of a few volts applied across the channel surfaces (See Supplementary Information S5).
Conclusion
The PDR, which is an individually addressable Si-based hybrid plasmonic disk resonator, has been theoretically and experimentally investigated. For the realization of the PDR coupled to the MISIM waveguide, standard CMOS technology has been used. The measured characteristics of the PDR coupled to the MISIM waveguide have been compared with the characteristics calculated by using the FDTD method. It has been shown that the former are in good agreement with the latter. When the radius of the Si disk is 0.9 μm, the loaded Q factor of the PDR is 24.6, and its intrinsic Q factor is estimated to be 57. If the fabrication process is improved, the intrinsic Q factor is expected to increase up to the theoretical value of 317. The loaded Q factor is also likely to approach 71.2 if the structural parameters of the coupling region are appropriately adjusted and the width of the Si strip of the MISIM waveguide is reduced to 50 nm. As a refractive index sensor, the realized PDR coupled to the MISIM waveguide has a sensitivity of 214 nm/RIU and it is very attractive in terms of requiring an extremely small volume of analyte. The PDRs are expected to open the door to ultracompact devices exploiting functional fluids such as liquid crystal.
Methods
Fabrication
To realize the PDR coupled to the MISIM waveguide, first, this device with the channels filled with SiO2 was fabricated by using standard CMOS technology. The first step of the fabrication was low pressure chemical vapor deposition (LPCVD) of 50-nm-thick Si oxide and 100-nm-thick Si nitride, which was used as an etch stop for the following chemical mechanical polishing (CMP), on an 8-inch silicon-on-insulator wafer with 2-μm-thick buried oxide. Then, 248 nm optical lithography and dry etching were carried out to make Si patterns. Over the patterns, 800-nm-thick Si oxide was formed by using high-density plasma chemical vapor deposition. To make the Si oxide surface planar, CMP was done. For the following Cu damascene process, another 248 nm optical lithography and dry etching were carried out to selectively remove the Si oxide and expose the Si patterns associated with the MISIM waveguides and the PDRs. Then, a thin Si oxide layer was conformally covered over the exposed Si patterns by using LPCVD. Finally, 800-nm-thick Cu was deposited by sputtering, and Cu CMP was done until the top surface of the thin Si oxide layer was exposed. These steps are the same as in ref. 20 and they were carried out by using the fabrication services provided by National Nanofab Center (www.nnfc.re.kr). Identical chips with the PDR-coupled MISIM waveguides, which have dimensions of 20 mm × 15 mm, were made on the wafer. One chip was diced out of the wafer, and a SU-8 microfluidic channel was formed on it by patterning SU-8 (MicroChem, SU-8 2015). Then, the channel-filling SiO2 was etched away with the SU-8 pattern used as an etching mask. The chip was immersed into buffered oxide etchant solution (JT Baker, Model 1178-03) for 55 seconds, thoroughly rinsed with deionized water, and dried. Finally, the chip was diced to make the input and output facets of the Si photonic waveguides with a 5-μm-wide core. During the dicing, the SU-8 pattern again plays the important role of reducing dicing-induced damage to the Si photonic waveguides. These steps are the same as in ref. 24.
Measurement
Two lensed fibers (of spot diameter 2.5 ± 0.3 μm, OZ Optics) was end-fire coupled to the 5-μm-core Si waveguides. Horizontally polarized light from a tunable laser (New Focus, Model TLB-6600) was launched into the input lensed fiber, and the light from the output lensed fiber was measured by an optical power meter (Newport, Model 2936-R). The transmission spectrum of the MISIM waveguide coupled to the PDR was normalized to that of the MISIM waveguide uncoupled to the resonator. Before the measurement, one of the index oils (Cargille, Series A, AA, and AAA) was dropped into the SU-8 channel and filled it. After the measurement, the chip was rinsed with methanol and deionized water, dried, and then reused.
Simulation
The PDR was analyzed by using the FDTD method (FDTD Solutions, Lumerical Inc.). The dielectric constant of Cu was calculated using the material model built in FDTD Solutions, which is based on the measured dielectric constant in ref. 33. When the isolated PDR was analyzed, an electric dipole source aligned radially was placed inside the channel. When the PDR-coupled MISIM waveguide was analyzed, the fundamental mode of the MISIM waveguide, which is called a hybrid plasmonic mode19, was launched into the left side of the MISIM waveguide before the PDR. The power of the right side of the MISIM waveguide after the PDR was monitored. Similar to the measurement, the transmission which is the ratio of the monitored power to the launched power was normalized to that of the isolated MISIM waveguide with the same length as the PDR-coupled MISIM waveguide.
The effective mode volume Veff of the resonance mode was calculated using the expression34
where E(r) is the electric field of the resonance mode and ε(r) is the dielectric constant distribution in the isolated PDR. In addition, the Purcell factor Fp was calculated by using .
For the fitting process, first, the isolated PDR with rD = 0.9 μm was analyzed by using the bend mode solver of FIMMWAVE (Photon Design) based on the finite element method. This analysis provided the effective index ND (=βD/(2π/λm)) and group index Ng of the resonance mode. Then, the values of aC, αD, τ, and θ were determined from the fitting process. The intrinsic Q factor of the isolated PDR was calculated by using the relation Qi = πNg/(αDλm), and the loaded Q factor of the PDR coupled to the MISIM waveguide was given by the ratio of λm to the linewidth of the fitted transmission spectrum.
Additional Information
How to cite this article: Kwon, M.-S. et al. Plasmofluidic Disk Resonators. Sci. Rep. 6, 23149; doi: 10.1038/srep23149 (2016).
References
Vlasov, Y., Green, W. M. J. & Xia, F. High-throughput silicon nanophotonic wavelength-insensitive switch for on-chip optical networks. Nat. Photon. 2, 242–246 (2008).
Bogaerts, W. et al. Silicon microring resonators. Laser Photonics Rev. 6, 47–73 (2012).
Li, G. et al. Ring Resonator modulators in silicon for interchip photonic links. IEEE J. Sel. Topics Quantum Electron. 19, 3401819 (2013).
Vos, K. D., Bartolozzi, I., Schacht, E., Bienstman, P. & Baets, R. Silicon-on-insulator microring resonator for sensitive and label-free biosensing. Opt. Express 15, 7610–7615 (2007).
Claes, T. et al. Label-free biosensing with a slot-waveguide-based ring resonator in silicon on insulator. IEEE Photon. J. 1, 197–204 (2009).
Grist, S. M. et al. Silicon photonic micro-disk resonators for label-free biosensing. Opt. Express 21, 7994–8006 (2013).
Vahala, K. J. Optical microcavities. Nature 424, 839–846 (2003).
Xu, Q., Fattal, D. & Beausoleil, R. G. Silicon microring resonators with 1.5-μm radius. Opt. Express 16, 4309–4315 (2008).
Shainline, J. et al. Subwavelength silicon microcavities. Opt. Express 17, 23323–23331 (2009).
Soltani, M., Li, Q., Yegnanarayanan, S. & Adibi, A. Toward ultimate miniaturization of high Q silicon traveling-wave microresonators. Opt. Express 18, 19541–19557 (2010).
Song, Y., Wang, J., Yan, M. & Qiu, M. Subwavelength hybrid plasmonic nanodisk with high Q factor and Purcell factor. J. Opt. 13, 075001 (2011).
Dai, D., Shi, Y., He, S., Wosinski, L. & Thylen, L. Silicon hybrid plasmonic submicron-donut resonator with pure dielectric access waveguides. Opt. Express 19, 23671–23682 (2011).
Chu, H.-S., Akimov, Y., Bai, P. & Li, E.-P. Submicrometer radius and highly confined plasmonic ring resonator filters based on hybrid metal-oxide-semiconductor waveguide. Opt. Lett. 37, 4564–4566 (2012).
Lou, F., Dai, D., Thylen, L. & Wosinski, L. Design and analysis of ultra-compact EO polymer modulators based on hybrid plasmonic microring resonators. Opt. Express 21, 20041–20051 (2013).
Xiang, C., Chan, C.-K. & Wang, J. Proposal and numerical study of ultra-compact active hybrid plasmonic resonator for sub-wavelength lasing applications. Sci. Rep. 4, 3720 (2014).
Zhu, S., Lo, G. Q. & Kwong, D. L. Experimental demonstration of horizontal nanoplasmonic slot waveguide-ring resonators with submicrometer radius. IEEE Photon. Technol. Lett. 23, 1896–1898 (2011).
Zhu, S., Lo, G. Q. & Kwong, D. L. Performance of ultracompact copper-capped silicon hybrid plasmonic waveguide-ring resonators at telecom wavelengths. Opt. Express 20, 15232–15246 (2012).
Lou, F., Thylen, L. & Wosinski, L. Experimental demonstration of silicon-based metallic whispering gallery mode disk resonators and their thermo-tuning. Optical Fiber Communication Conference 2014. OSA Technical Digest (online), paper Tu2E.1 (2014).
Kwon, M.-S. Metal-insulator-silicon-insulator-metal waveguides compatible with standard CMOS technology. Opt. Express 19, 8379–8393 (2011).
Kwon, M.-S., Shin, J.-S., Shin, S.-Y. & Lee, W.-G. Characterizations of realized metal-insulator-silicon-insulator-metal waveguides and nanochannel fabrication via insulator removal. Opt. Express 20, 21875–21887 (2012).
Shin, J.-S., Kwon, M.-S., Lee, C.-H. & Shin, S.-Y. Investigation and Improvement of 90° Direct Bends of Metal–Insulator–Silicon–Insulator–Metal Waveguides. IEEE Photon. J. 5, 6601909 (2013).
Kwon M.-S. & Shin, J.-S. Investigation of 90° submicrometer radius bends of metal-insulator-silicon-insulator-metal waveguides. Opt. Lett. 39, 715–718 (2014).
Han, Z., Van, V., Herman, W. N. & Ho, P.-T. Aperture-coupled MIM plasmonic ring resonators with sub-diffraction modal volumes. Opt. Express 17, 12678–12684 (2009).
Ku, B., Shin, J.-S. & Kwon, M.-S. Experimental investigation of plasmofluidic waveguides. Appl. Phys. Lett. 107, 201104 (2015).
Duan, C., Wang, W. & Xie, Q. Review article: fabrication of nanofluidic devices. Biofluidics 7, 026501 (2013).
Calus, S., Rau, D., Huber, P. & Kityk, A. V. Influence of nanoconfinement on the nematic behavior of liquid crystals. Phys. Rev. E 86, 021701 (2012).
Garcia, A. L. et al. Electrokinetic molecular separation in nanoscale fluidic channels. Lab Chip 5, 1271–1276 (2005).
Karnik, R. et al. Electrostatic control of ions and molecules in nanofluidic transistors. Nano Lett. 5, 943–948 (2005).
Vlassiouk, I. & Siwy, Z. S. Nanofluidic diode. Nano Lett. 7, 552–556 (2007).
Kim, J. Joining plasmonics with microfluidics: from convenience to inevitability. Lab Chip 12, 3611–3623 (2012).
Wang, M. et al. Plasmofluidics: merging light and fluids at the micro-/nanoscale. Small 11, 4423–4444 (2015).
Brolo, A. G. Plasmonics for future biosensors. Nat. Photon. 6, 709–713 (2012).
Lee, H. S. et al. Loss mechanisms of surface plasmon polaritons propagating on a smooth polycrystalline Cu surface. Opt. Express 20, 8974–8981 (2012).
Iwase, H., Englund, D. & Vučković, J. Analysis of the Purcell effect in photonic and plasmonic crystals with losses. Opt. Express 18, 16546–16560 (2010).
Acknowledgements
This research was supported by Basic Science Research Program through the National Research Foundation of Korea (NRF) funded by the Ministry of Education (2013R1A1A2A10062227).
Author information
Authors and Affiliations
Contributions
M.-S.K. developed, designed, and supervised this work. B.K. fabricated and measured the devices. B.K. and Y.K. simulated the devices. Especially, Y.K. calculated the effective mode volume of the resonator. M.-S.K. wrote this paper with input from B.K. and Y.K.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Kwon, MS., Ku, B. & Kim, Y. Plasmofluidic Disk Resonators. Sci Rep 6, 23149 (2016). https://doi.org/10.1038/srep23149
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep23149
This article is cited by
-
Plasmonic Ring Resonator Sensor with High Figure of Merit and Sensitivity Using Degenerate N-Doped Silicon for SPP Excitation
Plasmonics (2024)
-
Parametric Optimization of Hybrid Plasmonic Waveguide-Based SOI Ring Resonator Refractive Index Sensor
Plasmonics (2022)
-
Hybrid Plasmonic SOI Ring Resonator for Bulk and Affinity Bio - sensing Applications
Silicon (2022)
-
Plasmonic effects in composite metal nanostructures for sensing applications
Journal of Nanoparticle Research (2018)
-
Simultaneous realization of high sensing sensitivity and tunability in plasmonic nanostructures arrays
Scientific Reports (2017)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.