Transport measurements are powerful tools to probe electronic properties of solid-state materials. To access properties of local electronic states in nanostructures, such as local density of states, electronic distribution and so on, micro-probes utilizing artificial nanostructures have been invented to perform measurements in addition to those with conventional macroscopic electronic reservoirs. Here we demonstrate a new kind of micro-probe: a fast single-lead quantum dot probe, which utilizes a quantum dot coupled only to the target structure through a tunneling barrier and fast charge readout by RF reflectometry. The probe can directly access the local electronic states with wide bandwidth. The probe can also access more electronic states, not just those around the Fermi level, and the operations are robust against bias voltages and temperatures.
New kinds of structures based on solid-state nanostructures have been proposed to realize functional devices. For example, spintronics devices utilizing spin effects1,2 and quantum information-processing devices utilizing quantum effects in nanostructures3,4,5 have been proposed and studied intensively. In these new devices, local electronic states play important roles and their understanding on a microscopic basis is crucial.
Transport measurements are one of the most powerful tools to probe electronic properties of nanostructures. In conventional transport measurements, macroscopic probes, electronic reservoirs that contain huge ensembles of electrons, are coupled to the target system and the flow of electrons is measured to probe electronic properties6. Using such macroscopic electronic reservoirs brings some constraints in the measurement of nanostructures: direct access to small local regions is not easy, the transport is limited to only around the Fermi level, the measurement is greatly affected by change of the electronic distribution in the reservoir, for example caused by bias voltages or electron temperatures, and the measurement is usually slow because of the large geometric capacitances of the leads. To overcome these restrictions is a strong challenge in transport measurements.
One possible solution to this challenge requires microscopic probes utilizing nanostructures instead of macroscopic reservoirs. The use of semiconductor quantum dots (QDs) in such probes has been demonstrated. QDs have well defined inner quantum levels that can be controlled by applying voltages on gate electrodes7,8,9. By measuring the transport through these artificial quantum levels, we directly access local electronic states. This cannot be realized with conventional macroscopic probes. For example, measurements of local electronic states, energy relaxation and heat transport in quantum Hall edge states have been demonstrated by utilizing QDs10,11,12.
In this paper, we realize a new kind of QD probe: a fast single-lead quantum dot (SLQD) probe. An SLQD is a QD, which couples to a target system through a single tunneling barrier13,14,15,16. We can probe more states, not only those around the Fermi level, with robustness against change of the electronic distribution because the SLQD is fully isolated from electronic reservoirs. Also, we can improve the operation time of the probe because the geometric capacitance of the SLQD is small and by utilizing RF reflectometry techniques17,18,19.
First, we realized the fast SLQD probe and evaluated its operation speed. Second, we applied the probe to detect local electronic states in another QD, which is used as a controllable target nanostructure in this experiment. By measuring tunneling events of electrons between the probe SLQD and the target QD, we confirmed the operation of the new probe. Additionally, we demonstrated its key features. Finally, we show that this probe can conduct fast real-time measurements of local electronic states.
Realization of a fast single-lead quantum dot probe
Figure 1(a) is a scanning electron micrograph of the device. By applying negative voltages on the gate electrodes, a probe SLQD, a target QD and a QPC charge sensor20,21,22,23 are formed at the upper left, the lower middle and the upper right, respectively. The QPC charge sensor is connected to an RF resonator formed by an inductor L and a stray capacitance Cp (resonance frequency fres = 211 MHz). The number of electrons in the probe SLQD n is monitored by the intensity of the reflected RF signal Vrf. Another possible option to monitor n will be the dispersive readout using the gates24 of the SLQD, which will simplify the device structure.
First, we formed only the probe SLQD and coupled the probe to the two-dimensional electron gas to check the operation speed of the probe. Figure 1(b) is a charge state diagram of the SLQD. We measured Vrf as a function of a plunger gate votage VPP and a tunneling gate voltage VPT. To make signals clearer, we plotted numerical differentials of the signals dVrf/dVPP in Fig. 1(b). When n changes with change of VPP, Vrf shows jumps that are observed as bright lines in the figure. Note that the absolute value of n is not exactly one in this device and is expected around ~10 from the size of the QD and the interval between the charge transition lines. In experiments in the range of this paper, n = 1 is not necessary. As VPT is changed to more negative voltages, the charge transition lines become less visible because tunneling rates become small and electron tunneling into the SLQD rarely happens within the time scale of the VPP sweep (~1 ms, VPP was swept by saw-tooth wave voltages with a frequency of 1160 Hz).
We evaluated the measurement time that is required to resolve a single electron charge in this probe SLQD. Figure 2(a) shows the number of events N(Vrf)/Ntot as a function of Vrf and measurement time tmeas. This histogram is produced as a result of Ntot = 8192 repetitions of the measurement. The gate condition of the probe SLQD is fixed at point A in Fig. 1(b) on a charge transition line. At this point, the charge state changes between n and n + 1 states in a time scale of several hundreds of μs. In our measurement setup, a reflected RF signal is demodulated, digitized and integrated on tmeas to produce Vrf. With the increase of tmeas, it becomes possible to distinguish two peaks originating from n and n + 1 charge states. The left (right) peak corresponds to the n (n + 1) state. Figure 2(b) is a histogram at tmeas = 5 μs. The two peaks are well fitted by a double gaussian. We can resolve the n and n + 1 charge states with fidelity exceeding 99%. This value of tmeas is much shorter than values in previous experiments with conventional slow electronics (~ms)14,15,16.
Then we measured real-time tunneling into the probe SLQD. Figure 2(c) shows Vrf as a function of time t with changing VPP around point A in Fig. 1(b). This real time measurement of charge transition is often used as a benchmark of fast electronic measurements25,26. tmeas was fixed at 5 μs. The traces (offset by 50 mV) show transitions between VPP = −1553.3 to −1551.5 mV. As we increase VPP, the charge state changes from n to n + 1 and jumps of Vrf are observed around VPP = −1552.4 mV. We could resolve tunneling events as fast as several tens of μs and this result is consistent with the result in Fig. 2(b). With less negative values of VPP, the state converges to the n + 1 charge state.
Measurement of local electronic states in a target quantum dot
Next, we formed the target QD by applying negative voltages on the gates at the lower side of the device in Fig. 1(a). We probed inner electronic states of the target QD by using the SLQD probe. To detect the states of the target QD, we use the tunneling of electrons between the target QD and the probe SLQD. We now apply a continuous square wave voltage on VPP in order to periodically induce electron tunneling from the target QD to the probe SLQD. The corresponding energy diagram is shown in Fig. 3(a). The levels in the probe SLQD and the target QD are shifted by the applied square waves and are shown as pairs of lines. The filled ranges between the lines indicate windows in which the levels move. When the Fermi level of the reservoir EF is in the window of the target QD, and the window of the target QD is in the window of the probe SLQD as in case II, tunneling of electrons is synchronized with the applied square waves. In the other cases, I and III, the tunneling does not occur because the levels are kept empty or filled in all phases of the square waves.
Figure 3(b) shows measurement of electron tunneling into the probe SLQD in the time domain. Vrf is plotted as a function of time t. We applied a square wave with amplitude 16 mV and frequency 5 kHz. The origin of the horizontal axis is set at falling edges of the square wave. The plotted values of Vrf are the result of averaging 4096 measurements similar to measurements shown in Fig. 2(c). The traces (offset by −20 mV) show results with VPP = −1070, −1050, −1030 mV and these correspond to case I, II and III, respectively. In cases I and III, there is no electron tunneling and Vrf exhibits a square wave shape resulting from the direct electrostatic coupling between the applied square wave voltage and the charge sensor. On the other hand, in case II, electron tunneling events are synchronized with the square wave. This tunneling process is stochastic and produces exponential-decay changes of Vrf on the square wave background by averaging a large number of time traces.
Figure 3(c) is a close-up of the energy diagram for case II and in a case of electron tunneling from the target QD to the probe SLQD. If the level of the target QD is not aligned to the level of the probe SLQD like in cases i and iii, tunneling is suppressed as it is an inelastic process. On the other hand, when the levels are aligned as in case ii, tunneling is an elastic process and enhanced27,28. Therefore, we can detect the target level as an enhancement of the tunneling into the probe SLQD. (The same mechanism also works in a case of tunneling from the probe SLQD to the target QD.)
The corresponding data in such a scheme is shown in Fig. 3(d). Traces (offset by −20 mV) show the results with VPP = −1053, −1052, −1051 mV and these correspond to case i, ii and iii, respectively. The average electron tunneling time from the target QD to the probe SLQD in case ii (12 μs) is shorter than the values in cases i (105 μs) and iii (39 μs) as expected. This result shows that operation of the detection scheme utilizing tunneling of electrons is confirmed by the measurement of electron tunneling with the wide-band probe.
Next, we checked the modulation of the tunneling with changing VPP and a plunger gate voltage of the target QD VTP. Figure 4(a) shows a synchronized component of Vrf with the applied square wave Vsync measured by using the lock-in technique as a function of VPP and VTP. Vsync will be decreased when electron tunneling happens as shown in Fig. 3(d)ii. We can see several black lines from the lower left to the upper right and these correspond to conditions at which the levels in the target QD and the probe SLQD align and electron tunneling occurs. By considering the energies of excited states in both QDs, which are evaluated in another experiment as 200 and 480 μeV for the target QD and the probe SLQD, lines in region A correspond to electron tunneling from states in the target QD to the ground state in the SLQD, region B corresponds to tunneling from states in the target QD to the excited state in the SLQD, and region C corresponds to tunneling from the ground state of the probe SLQD to states in the target QD as shown in Fig. 4(b). The solid and dotted lines in the figure show the ground and the excited states, respectively.
The thick band structure from the upper left to the lower right corresponds to the electron tunneling between the target QD and the reservoirs because the charge sensor also has finite sensitivity to the charges in the target QD. The relative signal intensity by the target QD is about half of that by the probe QD reflecting the smaller capacitive coupling between the target QD and the sensor. The lower left edges of the black lines are points at which the target QD level is aligned to the Fermi level of the reservoirs in the injection phase. Moving to the upper right along the black lines, the target level goes below the Fermi level. The upper right edges of the black lines correspond to the points at which the target level is 450 μeV below the Fermi level. Even at this condition, we could detect the target levels with the SLQD probe. We observe electronic states of the target QD with line width as small as 30 μeV by considering that the coupling to the probe SLQD (several tens of μs) does not broaden the target levels. These results show that the SLQD probe can access levels, not just those around the Fermi level, with good energy resolution.
Robustness of the measurement by a single-lead quantum dot probe
Next, we checked the robustness of our measurement scheme against the electronic distribution in the reservoirs of the device. Figures 5(a,b) show bias voltage dependence of Coulomb peaks through the target QD (a) and the corresponding tunneling signal measured by the SLQD probe (b). The traces (offset by 50 in Fig. 5(b)) show results when we change the source drain bias voltage of the target QD Vsd from 50 to 400 μV with 50 μV step. The width of the Coulomb peaks are shown as open circles in Fig. 5(c). The width is taken at 1/3 of the peak height in order to prevent the effect of excited states, which changes the shape of the peaks29. We observe an increase of the width with the increase of Vsd. Filled circles in Fig. 5(c) are the width of the SLQD probe signal evaluated by FWHM. Strikingly, the width of the peaks is unaffected by the change of Vsd. This proves that the measurement by the SLQD probe is robust against Vsd.
Then, we studied the temperature dependence of the Coulomb peaks and the SLQD probe signal, as shown in Fig. 5(d,e). The traces (offset by 50 in Fig. 5(e)) show results with changing temperature of the fridge T from base temperature (13 mK) to 400 mK with 100 mK steps. The FWHM of the Coulomb peaks as a function of T is shown as open circles in Fig. 5(f). The width increases with the increase of T reflecting the broadening of the Fermi distribution in the reservoirs. The width of the SLQD probe signal, shown as filled circles in Fig. 5(f), shows no dependence on T. These results show that the measurement by the SLQD probe can access the local electronic states precisely, liberated from the electronic distribution of the reservoirs.
Real-time measurement of the target quantum dot states
Finally, we monitored the charge state of the target QD by using the fast SLQD probe. To detect the charge states of the target QD in real time with the SLQD probe, we again use the inter-dot tunneling when we apply a small square wave voltage on VPP. Measurements and refreshments of the probe are repeated by applying the square wave. We lowered the response time of the SLQD probe by making the inter-dot tunneling faster than 5 μs and also by making the charge transition time of the target QD slower in the accessible range of the probe. If the target QD level is empty, inter-dot tunneling does not occur (Fig. 6(a)). On the other hand, if the level is filled, inter-dot tunneling synchronized with the square wave occurs (Fig. 6(b)). This inter-dot tunneling can be detected by the SLQD probe.
Figure 6(c) shows the observed Vrf as a function of time. We applied a square wave (frequency 12.5 kHz, amplitude 2 mV) and the resulting square wave shaped Vrf, which comes from direct electrostatic coupling between VPP and the charge sensor, is observed. The traces show these results when we changed the target QD levels from beneath the Fermi level to above. We can observe two kinds of oscillation amplitudes. If an inter-dot electron tunneling occurs, the electron screens the applied square wave and the amplitude decreases. Therefore, the region with the small amplitude shaded in Fig. 6(c) corresponds to the filled condition of the target QD. We can clearly see the real-time jump of the target QD charge sate and the jump events depend on the energy of the target QD levels against the Fermi level.
In conclusion, we have realized a fast SLQD probe, which can access local electronic states in nanostructures with wide bandwidth. We evaluated the operation speed of the probe and applied this new probe to a measurement of the states in a target QD. We confirmed the operation of the probe and demonstrated its characteristic properties.
The new SLQD probe shows three superior properties compared to previous probes; (1) the SLQD probe can access more states, not just those around the Fermi level, (2) measurement by the SLQD probe is robust against change of electronic distribution in the reservoirs, (3) fast real-time measurement is possible. Properties (1) and (2) are the result of the single-lead quantum dot structure, in which the probe state is fully isolated and freed from electronic distribution of the electron bath. These properties will be powerful for measuring fragile local electronic states and their dynamics in nanostructures. For example, the probe will be useful to probe Kondo states under non-equilibrium conditions30,31,32 and to readout the electron spin in QDs33,34 with high fidelity even at relatively high electron temperatures.
Device structure and measurement
The device was fabricated from a GaAs/Al 0.3 Ga 0.7 As heterostructure wafer with sheet carrier density 2.0 × 1015 m−2 and mobility 110 m2/Vs at 4.2 K. The two-dimensional electron gas is formed 90 nm underneath the surface. We patterned a mesa structure by wet-etching and formed Ti/Au Schottky surface gates by metal deposition, which appear white in Fig. 1(a). All of the measurements were conducted in a dilution fridge at a temperature of 13 mK.
How to cite this article: Otsuka, T. et al. Fast probe of local electronic states in nanostructures utilizing a single-lead quantum dot. Sci. Rep. 5, 14616; doi: 10.1038/srep14616 (2015).
We thank J. Beil, J. Medford, F. Kuemmeth, C. M. Marcus, D. J. Reilly, K. Ono, RIKEN CEMS Emergent Matter Science Research Support Team and Microwave Research Group in Caltech for fruitful discussions and technical supports. Part of this work is supported by the Grant-in-Aid for Research Young Scientists B, Funding Program for World-Leading Innovative R&D on Science and Technology (FIRST) from the Japan Society for the Promotion of Science, ImPACT Program of Council for Science, Technology and Innovation, Toyota Physical & Chemical Research Institute Scholars, RIKEN Incentive Research Project, Yazaki Memorial Foundation for Science and Technology Research Grant, Japan Prize Foundation Research Grant, Advanced Technology Institute Research Grant, IARPA project “Multi-Qubit Coherent Operations” through Copenhagen University, Mercur Pr-2013-0001, DFG-TRR160, BMBF - Q.com-H 16KIS0109, and the DFH/UFA CDFA-05-06.
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/