Abstract
The fissure patency of a rock mass is an important factor contributing towards the fluid production efficiency. Debris particles generated by the crushing of rock masses or other external forces can cause blockage or promote the smoothness of rock fractures. It is of immense theoretical and engineering value to analyze the mechanics of particles in rock fissures, especially under the compression of rock from both sides. In this study, through static analysis, the resultant force of particles in rock fissures is extruded by rock on both sides. The following conclusions are drawn: The resultant force increases first and then decrease with the increase of fissure angle and width when x is constant. The extreme point is at sinθ = R/(3x), h = 2 R(9x2 − R2)0.5/(9x) and the maximum of F is 8πkR4/(27x). Whereas, the bigger the joint roughness coefficient (JRC) of fissure is, the larger the average of fissure open angle is and the larger the average width is. As the JRC increases, the average resultant force decreases. The sharp point at the turning point of the fissure is easily broken, and the fissure width becomes larger, which makes the resultant force decrease. The analysis process expands the application prospects of the JRC. The results help to better understand the blockage and transport of particles in rock fissures.
Similar content being viewed by others
Introduction
In the context of groundwater driving, the mechanical action and mechanical mechanism of transport particles1 in rock fissures have attracted a significant amount of attention from researchers. The sediment particles in a fissure can be called the underground sediment. The sediment composed of soil particles from the interior of soils2,3, rock fissures, porous soils4, riverbanks and some other sources constitutes underground sediment. Silt and scour may be created during the movement of underground sands, which block and dredge fissures5. A particle’s clogging and scouring are related to the outflow velocity and production efficiency of underground fluid in a rock mass.
Coupled transporting research of soil particles and groundwater in soils and rock is an important research topic of interest, especially in rock fissures6. This field involves particle mechanics7, fluid mechanics, seepage mechanics, and solid mechanics. Heap and Kennedy6, by studying the scale-dependent permeability of fractured andesite, found that the equivalent permeability coefficient depends heavily on the initial rock permeability and the scale of interest6. Sun7 researched the permeability of particle soils under soil pressure and established the proposed model of soil particle penetration, which can be directly used to calculate the permeability coefficient. Candela, et al.1 conducted experiments on permeability and fracturing and found that permeability sensitivity to dynamic stressing increases after fracturing, which is a process that generates abundant particulate matter in situ.
Under the driving of the underground fluid transport, the sediment is not only affected by the pressure of the fluid but also by the crush mechanics of the rock surfaces on both sides of the fissure. A substantial amount of research in particle’s clogging and scouring in porous media has emerged4,8. However, few studies have been conducted on the effects of the squeeze mechanics and mechanism of particles by rock fissures on both sides. This study focuses on this lacuna and tries to understand the blockage and transport of particles in rock fissures.
In the process of rock formation9,10, the rock is cracked (as shown in Fig. 1a), and cracks occur in the soil owing to water evaporation (as shown in Fig. 1b,c), which can considerably affect the permeability of crustal rocks10. Following this, in the presence of water and under the water pressure, the sediment particles enter the crack (as shown in Fig. 1d). The ground sediment is driven by groundwater, which potentially causes many hazards. If the ground sediment is fully considered and closely connected with the geological material, many geologic hazards, such as collapse of riverbanks and blockage of groundwater and oil fissures2, could be better handled. If the sediment particles are very hard at this time, while the soil and the rock are very soft, it will appear that the sediment particles squeeze both sides of the rock and soils. Because the rock containing fractures and cracks is soft, the fractures and cracks can be deformed by the force of the hard particles. As shown in Fig. 1, the crack and the fracture are squeezed and get deformed by the hard particles. In this case, stress analysis of the sediment particles in the fissures is necessary.
The geometrical structure of the fissure surface in rock affects the force of particles moving in it. In the geological engineering field, the joint roughness coefficient (JRC) is an important parameter that is widely used in the strength evaluation of fractured rocks. Researchers have combined JRC and the joint wall compressive strength (JCS) to put forward formulas for the relationship between fracture morphology and strength11,12,13, called the JRC–JCS model. The JRC–JCS model can be used to determine the peak shear strength of fractured rocks. Based on a large number of model tests and field observations, Barton14 proposed the standard roughness grade section. The curve of JRC values is divided into 10 sections, the range of which is [0, 20]. In practical applications, the actual structural plane section curve is compared with the standard roughness grade section curve to determine the JRC value. Additionally, in this study, the particles moving in the rock fissure are connected with the JRC of fissures, which has expanded the application prospects of JRC.
The particle in the rock fissure is influenced by the physical and mechanical properties of rock, fluid, fissure and particle, and its force is complex. The static analysis is one of the most important research methods. The static analysis method is widely used in obtaining the stress and stain distribution and structure analysis. For example, Merazi, et al.15 successfully established a new hyperbolic shear deformation plate theory for the static analysis of a functionally graded material (FGM) plate based on neutral surface position. The CPT-based p-y analysis method16 for offshore mono-piles embedded in sands under the conditions of static and cyclic loading conditions is a static analysis with some functions. The static analysis of variable thickness of two-directional functionally graded porous materials is given by Rad, et al.17. Lopez-Guerra, et al.18 calculated the standard viscoelastic responses with multiple retardation times through the analysis of static force spectroscopy AFM data. The static analysis in the above studies mainly aims at the conventional structures or special mechanical materials, but the static analysis is not involved in the particles in the rock fissure.
In this study, the static analysis of hard spherical particles in a rock fissure is carried out to obtain the resultant force of the rock fissure on both sides. The resultant force along the fissure is calculated, and the relationship between the resultant force and the JRC is established. The influence of the fissure width and the angle between the two sides of rock surface on the resultant force is further studied. It is helpful to understand and solve the plugging and dredge the dam bottom fracture. Next, the sediment and sand are used to plug the rock fracture against leakage. The study in this aspect can provide reference to further developments related to fissure expansion19, fissure matrix porosity for the groundwater dual porosity model connecting overlapping continuous conduits network20, the permeability distribution affected by fracture21, Darcy–Brinkman flow model in narrow crevices22, and the stress analysis of the migrating underground sediment within the rock and soil. In hydraulic engineering, it can be applied to the understanding of the dam sediment leak stoppage, dam stability23 and groundwater fissure channel unclogging.
Method and Analysis
The sediment is bound by two sides of the fissure walls, and the other sides (partially from the other sides as well) are free. Therefore, mechanical analysis is necessary in the case of a hard particle moving in a soft rock fracture.
When a hard particle moves in a soft rock fracture, the rock wall deforms (as shown in Figs 1d and 2a), while the hard particle cannot deform or shows very little deformation that can be ignored. In Fig. 2a, the hard particle is pressed by the up and down rock wall. Figure 2b is the cross-section of Fig. 2a. Figure 2b is rotated by an angle into Fig. 2c, in which the fracture up flat is the horizontal plane. Figure 2d is the same as Fig. 2c. The black belt in Fig. 2e is the plane in which the force is same size. F′v is the resultant force of all f′v. from the upper soft rock plate. F′v2 is the other resultant force from the upper soft rock plate. R is the radius of the particle. F is the resultant force of F′v and F′v2.
In Fig. 2, f′ is the pressure of one point, and the direction of the pressure points to the particle center O. On the plate, the horizontal component of f′ is f′h, and the resultant force of all f′h is 0. f′v is the vertical component of f′.
In Fig. 2d,e,
where, k is the soft rock elastic coefficient, α and β are the angle in Fig. 2, and β is the max value of α.
Since \({f^{\prime} }_{v}=f^{\prime} \cos \,\alpha \):
The black area in Fig. 2e is given by:
The force is given by:
According to Eqs (1) and (2), Eq. (3) is changed into:
Given that α ∈ [0, β], F′v = F′v2 and cosβ = x sinθ/R in Fig. 2c, Eq. (4) is:
From the resultant force of F′v and F′v2 in Fig. 2c and Eq. (5), the hard particle joint force is:
The fissure width obtained from Fig. 2 is:
Impact of a Hard Particle in a Soft Fracture
Thus, the larger h is, the smaller F is when R > h/(2 cosθ), that is, when the diameter of the hard particle is more than the fissure width.
From Eq. (6), the derivative of F with respect to θ is,
where R-x sinθ > 0, so sinθ < R/x.
Make Eq. (8) = 0, then
where sinθ = R/x, F′|θ = 0, F = 0.
To further study the mechanics of a hard particle in a soft fracture, an example is considered. The diameter of the hard particle in Shahi and Kuru’s24 research is [0.35 mm, 1.18 mm]. According to Eq. (6), in this research, the diameter of the hard particle is chosen as [0.36 mm, 1.18 mm], that is, R ∈ [0.18 mm, 0.59 mm]. The fracture is very long, and the two sidewalls are nearly parallel.
As we know, if two walls are parallel, the angle between the two walls is zero. The fissure width is small, and the distance between two sidewalls of fissure is small. Therefore, the two sidewalls are nearly parallel. θ is very small. x = Rcosβ/sinθ = C/sinθ, where C is a constant. x is very large from the above formula and θ is very small.
From Fig. 1c, the fracture and crack schematic diagram shows bending and twists. Figure 1d is a part of the whole x length. x of rock fissure is not the real fissure length, but it indicates the relationship between the angle and length. The real fissure is not the whole of the x length, but the part of the x long fissure. R must be larger than x × sin(θ), so x < R/sin(θ). Therefore, this research chooses the x ∈ (0.2 mm, 2 mm] and θ ∈ (0, 0.8]. The case result is presented in Fig. 3.
In Fig. 3a, F increases with the increase of θ when sinθ < R/(3x) that is Eq. (8) > 0. Whereas when R/x > sinθ > R/(3x) that is Eq. (8) < 0, F increases with the decrease of θ.
So the maximum of F is 8πkR4/(27x) when sinθ = R/(3x).
In Fig. 3b, From Eq. (9), the derivative of F with respect to h is 0. F increases with the increase of h when h ∈ (0, 2 R(9x2 − R2)0.5/(9x)]. Whereas F decreases with the increase of h when h ∈ [2 R(9x2 − R2)0.5/(9x), 2 R(x2 − R2)0.5/x].
So the maximum of F is 8πkR4/(27x) when h = 2 R(9x2 − R2)0.5/(9x). This can be shown in Fig. 3a.
From Fig. 2c and Fig. 3b, the resultant force of the sphere particle is away from the top of the fissure. From Fig. 3a,b and Eq. (6), the increase of x will lead to the decrease of the resultant force. The increase in the angle causes the resultant force to increase first and then decrease. The extreme point is at sinθ = R/(3x) and h = 2 R(9x2 − R2)0.5/(9x). And the angle inside the fissure is not static but it changes.
When the fissure tip is consistent with the movement direction of the particle, the movement can be called forward movement, and this angle can be called a positive angle. Similarly, negative movement and negative angle can be defined. When the particles move in the fissures driven by groundwater, they encounter a positive angle and the particles are squeezed by the fissure surfaces, so that the particles are subjected to resistance. When negative angles are encountered, the particles are also squeezed by fissures, at which point the particles accelerate their movement.
From Fig. 3a,b and Eq. (6), the resultant force decreases with the increase of x.
The particle’s mechanics are affected by the roughness of the fissure, so we need to consider the roughness to connect with the particle’s mechanics. There are some cracks when the rock cracks. The crack can be treated as the joint of the two side rocks. All the ten typical roughness profiles (as shown in Fig. 4a) in references14,25 are chosen as the fissure case to calculate. This research chooses the curvature of the fissure curve as θ. The θ and curvature of the fissure curve is:
The fissure width increases with the curvature of the fissure curve. When θ is very small, h = 2xθ. x = 20 mm, h can be treated as 20 × sin(2θ). According to R ∈ [0.18 mm, 0.59 mm], we choose R = 0.2 mm. When R-xsin(θ) > 0, the particle is pressed. The particle is free and F = 0 when R-xsin(θ) < 0.
The ten fissure profiles, curvature and force results are presented in Fig. 4. Figure 4a shows the ten fracture profiles. Along the tenth fissure (as shown in Fig. 4b), the fissure’s curvature and the hard particle total force are shown in Figs 4c,d.
The mean of curvature, fissure width and F/(2kπ) of the ten fissures are listed in Table 1. The curvature mean is the average of all the curvatures along the fissure profile curve, based on Eq. (10). The fissure width is the result of Eq. (7), when x = 20 mm. The scale of maximum value θ is [0.0337, 0.443]. cosθ is [0.999,0.999]. F/(2kπ) is obtained according to Eq. (6) when the x < R/sin(θ). F/(2kπ) mean is the average value of all results when the x < R/sin(θ). While x > R/sin(θ), according to Eq. (6), the result of F/(2kπ) is not considered.
From Fig. 4a, the ten profiles show more bending as JRC increases. There are more turning and bending points on the higher JRC profiles. P1 is the smoothest and has the smallest JRC value, [0, 2]. P10 is the most tortuous with the largest JRC value [18, 20]. Figure 4c shows the curvature is different along the profile curve. The more the curvature is, the more the curve turns and bends. The more concentrated the turning points are, the more concentrated the large curvature values are. The curvature is 0 at smooth points. F/(2kπ) changes with the curvature (as shown in Fig. 4d). F/(2kπ) = 0 when the curvature is 0.
The resultant force F accelerates or decelerates the movement of the particle in the fissure. When the fracture dipping direction is consistent with the particle movement direction, F decelerates the particle movement. When the fracture dipping direction is against the particle movement direction, F accelerates the particle movement. The direction of the resultant force F is always opposite to the direction of the tip of the fissure.
From Table 1 and Fig. 5, it can be seen that the sequence number increases, JRC increases, curvature increases, fissure width mean (mm) increases, and F/(2kπ) decreases. The serial number decreases, JRC decreases, curvature decreases, and fissure width mean (mm) and F/(2kπ) increase.
Discussion
In Fig. 3, the particle force F is affected by θ and x. From Eq. (6), the resultant force obviously decreases with the increase of x. As the width of the fissure h is 2xsinθ·cosθ, the particle stress F is affected by the angle θ and the fissure width h. As shown in Table 1 and Fig. 5, there are two main factors that affect the size of particles: the angle between the two sides of the gap and the width of the seam h.
Effect of angle θ on force F
From Eq. (6), for a constant x, varying θ, R = 0.2 mm, and x = 20 mm, according to the formula (6), the relationship curve between F/(2kπ) and θ is drawn in Fig. 6. Figure 6a is the partial enlargement of Fig. 6b.
In Fig. 6a, F increases with the increase of θ when sinθ < 1/300 that is Eq. (8) > 0. Whereas when 1/100 > sinθ > 1/300 that is Eq. (8) < 0, F increases with the decrease of θ. So the maximum of F is 32πk/135 when sinθ = 1/300. F increases first and then decrease with the increase of θ.
The influence of the angle θ on the force F can also be analyzed from the microscopic morphology of the fissure. The microscopic morphology of the rock fissure is plotted in Fig. 7.
Figure 7a is a complex rock section. Figure 7b is a partial enlarged view of Fig. 7a. Figure 7c is a smooth section of the rock, and Fig. 7d is a partial enlarged view of Fig. 7c. Among them, the JRC of the rock fissure in Fig. 7a is larger than the JRC of the rock in Fig. 7c.
In Figs 4a and 7a,c, the larger the JRC is, the coarser the section is, the more turning points the surface has (as in Fig. 7a), the larger the turning degree is, and the larger the angle between the fissure two sides is (as in Fig. 7b). By contrast, the smaller the JRC is, the smoother the section is, the fewer turning points the surface has (as shown in Fig. 7c), the smaller the turning degree is, and the smaller the angle between the fissure two sides (Fig. 7d).
Effect of the fissure average width on the average force
In terms of a stress point of the particle on the fissure profile, when θ is a constant, the larger the fissure width h (h = 2xsinθ·cosθ) is, the larger the x is. At same time, the smaller the value of R-xsinθ, the smaller the force of the Eq. (6) is, as shown in Fig. 3.
The turning point of the rock section is greatly increased in Fig. 7a. Many rock debris are mixed in the fissure. Because the fissure is composed of two surfaces instead of two curves, a small rock particle can support a larger gap on both sides of the rock. At the same time, the rock surfaces on both sides of the section are easily misplaced, so the fracture surfaces on both sides do not have very good contact. The larger the distance between the rocks on both sides is, the larger the fissure width h1 (as shown in Fig. 7b) is. Therefore, h1 > h3 (as shown in Fig. 7d) and F1 < F3. By contrast, the turning point of the rock section is decreased and the cross section is smooth in Fig. 7c. The rock faces on both sides of the section can easily be placed in close contact. Because of the few points on the fracture surface, the debris in the fissure is minimal. Therefore, the rock space on both sides is smaller and the fissure width is smaller (as shown in Fig. 7d).
Violay, et al.26 discovered that the rock’s brittle behavior increases the porosity. Violay, et al.26 concluded that a rock with larger JRC is more brittle. The rock mass with higher porosity indicates that the fissure has a larger width and is more complex, and there are more fissures. Thus, we can conclude that the fissure having a larger JRC has a larger width and is more complex. Eqs (10) and (7) are reasonable. This research result is consistent with the discovery made in Violay, et al.26.
Given that the sharp point at the turning point is easily broken, the broken rock at the turning point results in more space, so h2 > h1 and F2 < F1.
Thus, the influence of the fissure width h on the resultant force F is suitably explained:
In Fig. 3b, F increases first and then decrease with the increase of h when x is constant. h ∈ (0, 2 R(x2 − R2)0.5/x]. When h > 2 R(x2 − R2)0.5/x, F = 0.
In Table 1 and Fig. 5, the average of F decrease with the increase of the average of h. The average of F is the average of all of F ≠ 0. The average of h is the average of all of h, including the h > 2 R(x2 − R2)0.5. For example, there are three points (h, F) on Fissure 1 that are (R(x2 − R2)0.5/x, F1), (2 R(x2 − R2)0.5/x, 0) and (3 R(x2 − R2)0.5/x, 0). The average of all of F is F1, and the average of all of h is 2 R(x2 − R2)0.5/x. There are three points (h, F) on Fissure 2 that are (2 R(x2 − R2)0.5/x, 0), (3 R(x2 − R2)0.5/x, 0) and (4 R(x2 − R2)0.5/x, 0). The average of all of F is 0, and the average of all of h is 3 R(x2 − R2)0.5/x. So F1 > 0, 2 R(x2 − R2)0.5/x < 3 R(x2 − R2)0.5/x.
So the rules shown in Fig. 3b and Table 1/Fig. 5 seem to be different. In fact, the above explanation well explains this different. x is constant in Fig. 3 and averaging the width h and angle θ in Table 1 and Fig. 5 is the key issue.
From the result in Fig. 4d, we can see that the total force from the two sides of the fissure changes along the fissure. The quantity of the force is connected with the fissure open angle and the fissure width.
This research combines the fissure open angle and the width to analyze the resultant force of a hard particle under both sides of the fissure. Along the fissure, the size of the resultant force is not regular and shows some randomness and uncertainty. This agrees with the general experimental observation because the fissure is caused by a fracture, and the material is heterogeneous. The expansion of the crack is very random, and the fissure width is uncertain. This is why the JRC27,28 is investigated in several studies. The trajectory shape, the surface roughness and the open angle of fissures play important roles in the mechanical action of particles.
Conclusion
In this study, the hard particle static force in a soft rock fracture is analyzed. The total force, as given in Eq. (6), is established. The power source is the groundwater seepage. The water motion causes the particle to be squeezed by the top and bottom rock plates. The results lead to a better understanding of the transporting of a nondeformable solid in a rock fissure. The analysis process provides a reference for the calculation of the transporting of underground sand through the fissure of rock-soil body at irrigation works.
In terms of a point on the fissure and a constant x, there are a fixed θ, h, F. F increases first and then decrease with the increase of θ and h. The average of h and θ have the similar effect on the average of F. The extreme point is sinθ = R/(3x), and h = 2 R(9x2 − R2)0.5/(9x). At the same time, the maximum of F is 8πkR4/(27x).
It is found that the bigger JRC of fissure is, the larger the average of fissure open angle θ is and the larger the average width h is. As the average width h or the average angle θ increases, the average resultant force of F decreases. The average of h and θ have the similar effect on the average of F.
Along the fissure, the size of the resultant force is not regular and shows some randomness and uncertainty. The mechanical effect of fissures on the particles is mainly affected by the trajectory morphology, surface roughness, and the open angle of the fissures. The measurement of these factors is an important part of the future study of the forces driven by subsurface fluids in fractures. The measurement of these factors is very important, especially in future mechanical studies on the particle movement driven by underground fluid in rock fissures.
The study can be used in these studies: Darcy–Brinkman flow model in narrow crevices29,30, clay fill in embankment fissures31, permeability of noncohesive soils32, the groundwater hydrology model33, and others.
The open angle and the width of rock fissures are calculated based on the fissure profile curvature, which conforms to a certain actual situation. In this research, the connection between the direction of the resultant force F and the fissure JRC is not considered because of the considerable difficulty in measuring the fissure. More detailed and more accurate calculation and measurement need to be carried out by technical researchers in the future.
References
Candela, T., Brodsky, E. E., Marone, C. & Elsworth, D. Laboratory evidence for particle mobilization as a mechanism for permeability enhancement via dynamic stressing. Earth & Planetary Science Letters 392, 279–291 (2014).
Sun, J. Survey and research frame for ground sediment. Environmental Science and Pollution Research 23, 18960–18965, https://doi.org/10.1007/s11356-016-7440-4 (2016).
Sun, J. Ground sediment transport model and numerical simulation. Polish Journal of Environmental Studies 25, 1691–1697, https://doi.org/10.15244/pjoes/60766 (2016).
Sun, J. Mathematical model coupling seepage and sedimentation of solid particles in porous media. Fresenius Environmental Bulletin 24, 1735–1741 (2015).
Rojstaczer, S. A., Ingebritsen, S. E. & Hayba, D. O. Permeability of continental crust influenced by internal and external forcing. Geofluids 8, 128–139 (2010).
Heap, M. J. & Kennedy, B. M. Exploring the scale-dependent permeability of fractured andesite. Earth & Planetary Science Letters 447, 139–150 (2016).
Sun, J. Permeability of Particle Soils Under Soil Pressure. Transport in Porous Media 123, 257–270, https://doi.org/10.1007/s11242-018-1038-x (2018).
Sun, J. & Wang, G. Transport model of underground sediment in soils. Scientific World Journal <<Go to ISI >>WOS:000326834100001 http://downloads.hindawi.com/journals/tswj/2013/367918.pdf. (2013).
Baak, S. H., Cho, G. C. & Song, K. I. Stability analysis on the concrete slab of the highest concrete-faced rock-fill dam in South Korea. Geomechanics and Engineering 13, 881–892 (2017).
Agliardi, F., Dobbs, M. R., Zanchetta, S. & Vinciguerra, S. Folded fabric tunes rock deformation and failure mode in the upper crust. Sci. Rep. 7, 9, https://doi.org/10.1038/s41598-017-15523-1 (2017).
Barton, N. Review of a new shear-strength criterion for rock joints. Engineering Geology 7, 287–332 (1973).
Grasselli, G. Manuel Rocha Medal Recipient Shear Strength of Rock Joints Based on Quantified Surface Description. Rock Mechanics & Rock Engineering 39, 295 (2006).
Liu, Q., Tian, Y., Liu, D. & Jiang, Y. Updates to JRC-JCS model for estimating the peak shear strength of rock joints based on quantified surface description. Engineering Geology 228 (2017).
Barton, N. & Choubey, V. The shear strength of rock joints in theory and practice. Rock Mecanics 10, 1–54 (1977).
Merazi, M., Hadji, L., Daouadji, T. H., Tounsi, A. & Bedia, E. A. A. A new hyperbolic shear deformation plate theory for static analysis of FGM plate based on neutral surface position. Geomechanics & Engineering 8, 305–321 (2015).
Kim, G., Kyung, D., Park, D. & Lee, J. CPT-based p-y analysis for mono-piles in sands under static and cyclic loading conditions. Geomechanics & Engineering 9, 313–328 (2015).
Rad, A. B., Farzan-Rad, M. R. & Majd, K. M. Static analysis of non-uniform heterogeneous circular plate with porous material resting on a gradient hybrid foundation involving friction force. Struct. Eng. Mech. 64, 591–610, https://doi.org/10.12989/sem.2017.64.5.591 (2017).
Lopez-Guerra, E. A., Eslami, B. & Solares, S. D. Calculation of Standard Viscoelastic Responses with Multiple Retardation Times Through Analysis of Static Force Spectroscopy AFMData. J Polym Sci Pol Phys. 55, 804–813, https://doi.org/10.1002/polb.24327 (2017).
Sun, J., Wang, G. & Sun, Q. Crack spacing of unsaturated soils in the critical state. Chinese Science Bulletin 54, 2008–2012, https://doi.org/10.1007/s11434-009-0319-8 (2009).
Hosseini, S. M. & Ataie-Ashtiani, B. Conceptualization of Karstic Aquifer with Multiple Outlets Using a Dual Porosity Model. Groundwater 55, 558–564, https://doi.org/10.1111/gwat.12504 (2017).
Bruna, P. O., Guglielmi, Y., Viseur, S., Lamarche, J. & Bildstein, O. Coupling fracture facies with in-situ permeability measurements to generate stochastic simulations of tight carbonate aquifer properties: Example from the Lower Cretaceous aquifer, Northern Provence, SE France. Journal of Hydrology 529, 737–753, https://doi.org/10.1016/j.jhydrol.2015.08.054 (2015).
Wang, C. Y. Darcy-Brinkman Flow in Narrow Crevices. Transport in Porous Media 120, 101–113, https://doi.org/10.1007/s11242-017-0911-3 (2017).
S Jichao & W Guangqian. Riverbank Collapse Mechanism Under Scouring (VDM Publishing House Germany, 2010).
Shahi, S. & Kuru, E. An experimental investigation of settling velocity of natural sands in water using Particle Image Shadowgraph. Powder Technol 281, 184–192, https://doi.org/10.1016/j.powtec.2015.04.065 (2015).
Tse, R. & Cruden, D. M. Estimating joint roughness coefficients. International Journal of Rock Mechanics and Mining Sciences & Geomechanics Abstracts 16, 303–307, https://doi.org/10.1016/0148-9062(79)90241-9 (1979).
Violay, M., Heap, M. J., Acosta, M. & Madonna, C. Porosity evolution at the brittle-ductile transition in the continental crust: Implications for deep hydro-geothermal circulation. Sci. Rep. 7, 10, https://doi.org/10.1038/s41598-017-08108-5 (2017).
Yong, R., Fu, X., Huang, M., Liang, Q. F. & Du, S. G. A rapid field measurement method for the determination of Joint Roughness Coefficient of large rock joint surfaces. Ksce Journal of Civil Engineering 22, 101–109, https://doi.org/10.1007/s12205-017-0654-2 (2018).
Li, Y., Oh, J., Mitra, R. & Hebblewhite, B. Experimental Studies on the Mechanical Behaviour of Rock Joints with Various Openings. Rock Mechanics and Rock Engineering 49, 837–853, https://doi.org/10.1007/s00603-015-0781-3 (2016).
Wang, C. Y. Analytical solution for forced convection in a semi-circular channel filled with a porous medium. Transport in Porous Media 73, 369–378, https://doi.org/10.1007/s11242-007-9177-5 (2008).
Wang, C. Y. F. T. Super-elliptic Ducts Filled with a Darcy-Brinkman Medium. Transport in Porous Media 81, 207–217, https://doi.org/10.1007/s11242-009-9394-1 (2010).
Dyer, M., Utili, S. & Zielinski, M. Field survey of desiccation fissuring of flood embankments. Proc. Inst. Civil. Eng.-Water Manag. 162, 221–232, https://doi.org/10.1680/wama.2009.162.3.221 (2009).
Richards, K. S. & Reddy, K. R. Kinetic Energy Method for Predicting Initiation of Backward Erosion in Earthen Dams and Levees. Environmental & Engineering Geoscience 20, 85–97, https://doi.org/10.2113/gseegeosci.20.1.85 (2014).
Hosseini, S. M., Ataie-Ashtiani, B. & Simmons, C. T. Spring hydrograph simulation of karstic aquifers: Impacts of variable recharge area, intermediate storage and memory effects. Journal of Hydrology 552, 225–240, https://doi.org/10.1016/j.jhydrol.2017.06.018 (2017).
Acknowledgements
This research is supported by the Fundamental Research Funds for the Central Universities (No.: 2652017164) and the Key Laboratory of Geological Information Technology, Ministry of Natural Resources of the People’s Republic of China. I am really grateful to the Editor, the Associate Editor, and anonymous reviewers for their constructive and insightful help, suggestions and comments, which led to a significant improvement of this paper.
Author information
Authors and Affiliations
Contributions
Jichao Sun completed all the work.
Corresponding author
Ethics declarations
Competing Interests
The author declares no competing interests.
Additional information
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Sun, J. Hard particle force in a soft fracture. Sci Rep 9, 3065 (2019). https://doi.org/10.1038/s41598-019-40179-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-019-40179-4
This article is cited by
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.