Abstract
Various studies on multi-valued-logic (MVL) computing, which utilizes more than two logic states, have recently been resumed owing to the demand for greater power saving in the current logic technologies. In particular, unlike old-fashioned researches, extensive efforts have been focused on implementing single devices with multiple threshold voltages via a negative-differential current change phenomenon. In this work, we report a multiple negative-differential-transconductance (NDT) phenomenon, which is achieved through the control of partial gate potential and light power/wavelength in a van-der-Waals (vdW) multi-channel phototransistor. The partial gating formed a controllable potential barrier/well in the vdW channel, enabling control over the collection of carriers and eventually inducing the NDT phenomenon. Especially, the strategy shining lights with different powers/wavelengths facilitated the precise NDT control and the realization of the multiple NDT phenomenon. Finally, the usability of this multiple NDT device as a core device of MVL arithmetic circuits such as MVL inverters/NAND/NOR gates is demonstrated.
Similar content being viewed by others
Introduction
With the advent of a hyper-connected society based on the Internet-of-Things, where more than one trillion objects are connected with each other via the Internet, the amount of data to be handled and the processing power consumption are expected to increase rapidly1,2,3,4. Under this circumstance, there have recently resumed various studies on the multi-valued logic (MVL) computing technology, which utilizes more than two logical states and enables power-efficient processing of information5,6,7. To realize such computing technology, it is important to achieve an MVL hardware platform that is based on MVL devices with a multi-threshold voltage (multi-VTH). Such MVL devices have been commonly developed in two ways: one uses a negative-differential transconductance (NDT) phenomenon and the other exploits a negative-differential resistance (NDR) phenomenon8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23. The NDT and NDR phenomena denote that the drain current decreases in a specific voltage region when the gate voltage (for NDT phenomenon) or drain voltage (for NDR phenomenon) increases, showing “N”-shaped current−voltage (I−V) characteristic curves. The MVL devices on the basis of the NDT and NDR characteristics were implemented by using various types of heterojunctions (types I, II, and III)17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32. In recent years, van-der Waals (vdW) materials, which have very low surface defect density and therefore enable to form high-quality heterojunctions via a simple stacking process33,34,35,36,37,38,39,40,41,42,43,44,45,46,47,48, have been proposed for the implementation of MVL devices17,18,19,20,21,22,23.
Until now, vdW material based MVL devices and circuits have been achieved through various approaches. Wang et al.20 demonstrated a tungsten disulfide (WS2)/tin disulfide (SnS2) heterojunction device that exhibits a single-peak NDR phenomenon, where a gate terminal was required to control the doping concentration of SnS2. Shim et al.21 reported a black phosphorus (BP)/rhenium disulfide (ReS2) heterojunction-based MVL device exhibiting the NDR phenomenon. They implemented a ternary inverter circuit that processes three logical states by adding a load device to the MVL device. However, the current flowing through the inverter circuit fluctuated greatly with small changes in the input voltage, making the intermediate state unstable. Meanwhile, Nourbaksh et al.22 and Shim et al.23, respectively reported molybdenum disulfide (MoS2)/tungsten diselenide (WSe2) and graphene/WSe2 heterojunction-based MVL devices featuring the NDT phenomenon. Notably, they demonstrated a ternary inverter circuit with a stable intermediate state, which was achieved by appropriately matching the I−V characteristics of NDT device with those of a p-channel load device. A BP/MoS2 heterojunction-based NDT device was reported by Huang et al.16, who proposed a hybrid channel consisting of p- and n-channel materials connected in series. They also demonstrated a ternary inverter circuit with an NDT device and BP load transistor. Beyond such a ternary logic regime, a quaternary logic device and circuit were recently reported by Lim et al.17. They implemented a WS2–graphene–WSe2 heterojunction MVL device that exhibits a double-peak NDT phenomenon and subsequently demonstrated the feasibility of a quaternary inverter configured with the double NDT device and p-channel load transistor. Although it was proven that the NDT-based MVL devices can be extended to the quaternary logic regime, complex heterojunctions consisting of at least two materials are required for the realization of such devices. Moreover, the approaches that have been proposed to date have focused on the application toward an MVL inverter, and there are relatively few studies that focus on MVL circuits beyond an inverter.
Here, we report a multiple NDT phenomenon achieved via the control of partial gate (PG) potential and light power/wavelength in a vdW multi-channel phototransistor, hereafter referred to as a PG-NDT device. The partial gating enables the formation of a controllable potential barrier/well in the middle of the vdW channel, which enables control over the collection of carriers and eventually induces the NDT phenomenon. In particular, the strategy to expose the PG-NDT device to different lights with various powers/wavelengths facilitates the precise control of the NDT phenomenon and the realization of the multiple NDT operation. We reveal the operating principle of the PG-NDT device by performing detailed analyses using three-dimensional (3D) atomic force microscopy (AFM), Raman spectroscopy, cross-sectional transmission electron microscopy (X-TEM), energy-dispersive X-ray spectroscopy (EDS), temperature-dependent electrical measurement, and Kelvin probe force microscopy (KPFM). Finally, we demonstrate the feasibility of the proposed PG-NDT device in the realization of multi-valued arithmetic logic circuits, such as ternary NAND/NOR gate circuits.
Results
Characterization of PG-NDT device
Figure 1a shows schematic and optical microscopy (OM) images of the PG-NDT device featuring a controllable potential barrier and/or well. This potential barrier and/or well was formed in the middle of the vdW channel by partially defining a gate region. As the gate voltage increases in the positive or negative direction, the energy band corresponding to part of the vdW channel shifts down or up, consequently inducing the potential barrier and/or well for injected and/or photo-generated carriers. Owing to the potential barrier and/or well that are varied by the gate voltage, it is possible to facilitate or suppress the collection of injected or photo-generated carriers at a specific voltage region, eventually leading to the abnormal decrease in the drain current (NDT phenomenon). The PG-NDT device was fabricated as follows: (i) a gate electrode with a width of 4 μm was formed on the SiO2/Si substrate. Here, the width of the gate electrode is narrower than the device channel length to be formed, which is a crucial requirement for the induction of the NDT phenomenon. (ii) Hexagonal boron-nitride (h-BN) for the gate dielectric and WSe2 for the vdW channel were simply stacked onto the gate electrode by using a residue-free transfer method employing adhesion energy engineering (Supplementary Fig. 1 and Supplementary Table 1). (iii) Then, source and drain electrodes were formed on the vdW channel, where the distance between two electrodes was 20 μm (details are presented in the “Methods” section). According to the three-dimensional (3D) atomic force microscopy (AFM) analysis, the thicknesses of the h-BN and WSe2 layers were ~52 and 51 nm, respectively (Fig. 1b). The PG-NDT device structure was also examined using cross-sectional transmission electron microscopy (X-TEM), as depicted in Supplementary Fig. 2. In particular, we confirmed the clean interface of the h-BN/WSe2 heterostructure using high-resolution X-TEM analysis (Supplementary Fig. 2). The results of the EDS analysis near the partially defined gate electrode are provided in Supplementary Fig. 3.
The drain current–gate voltage (ID−VG) characteristics of the conventional vdW transistor with a fully defined gate electrode and the PG-NDT device with a partially defined gate electrode were then investigated (Fig. 1c). For the conventional vdW transistor, when VG increased in the negative direction, the width of the tunneling barrier (WTN) for holes from the source to the vdW channels decreases, thereby increasing the ID continuously. Meanwhile, for the PG-NDT device with a partially defined gate electrode, when the VG increased in the negative direction from VG = 20 V to the vicinity of VG = 0 V, the value of ID continuously increased. This is because the potential barrier for holes gets lower, and the hole carriers, which are injected from the source, are collected better by the drain. When VG increased further in the negative direction from the vicinity of VG = 0 V to the vicinity of VG = − 8 V, an abnormal reduction in the ID was observed (here, the two vertexes are defined as the peak and valley). This is because as previously mentioned, VG induces the potential well for the injected hole carriers, thereby suppressing the collection of the carriers. Beyond the vicinity of VG = − 8 V, ID increased again as VG continued to increase negatively. Such a large negative VG is predicted to increase significantly the probability of the hole carrier injection from the source, consequently overwhelming the suppression effect by the potential well. An in-depth analysis and understanding of this NDT phenomenon are provided in the following subsection. Figure 1d shows the transconductance (gm = dID/dVG) with respect to the gate voltage extracted from the ID−VG characteristics. While a positive differential transconductance was observed in the entire range of VG for the conventional vdW transistor, a negative-differential transconductance appeared for a specific range of VG for the PG-NDT device. Such an NDT phenomenon was consistently observed in four different PG-NDT devices (Supplementary Fig. 4a). The peak and valley voltage values were distributed between 0.2 and 1.6 V and between −9.7 and −7 V, respectively (Fig. 1e). Moreover, similar NDT phenomena were observed in the PG-NDT devices fabricated with various vdW channel materials such as WS2, MoS2, and molybdenum diselenide (MoSe2), as provided in Supplementary Fig. 4b–d, respectively. The lower image in Fig. 1e shows the peak and valley voltages extracted from the NDT characteristic curves of the PG-NDT devices fabricated with MoSe2, MoS2, or WS2 channels (three device samples for each vdW channel). For the PG-NDT devices with MoSe2, MoS2, and WS2 channels, we confirmed approximately −10/−3 V (for MoSe2 channel), −7/−2 V (for MoS2 channel), and 0.2/7 V (for WS2 channel) of peak/valley voltages, respectively (Supplementary Fig. 4e).
In-depth analysis and understanding of the NDT phenomenon
To obtain an in-depth understanding of the NDT phenomenon, as shown in Fig. 2a, b, we performed the KPFM analysis and investigated the distribution of the contact potential difference (VCPD) between the tip and surface of the PG-NDT device for different VG values. Here, the width of the gate electrode and the length of the vdW channel were 1 and 20 μm, respectively. The measurement setup for the KPFM analysis is provided in the “Methods” section. Figure 2b shows the profile of the VCPD from points A to B, which is indicated in the OM image of Fig. 2a. When a VG value of 0.1 V was applied to the partially defined gate electrode, a potential barrier and/or well with a height of 0.058 eV and a width of 1.35 μm was observed in the middle of the vdW channel. As VG increased from 1, 5, to 10 V, the height and width of the potential barrier and/or well increased from 0.081, 0.103, to 0.132 eV (for the height) and from 1.65, 3.89, to 5.41 μm (for the width), respectively (Fig. 2c). Similarly, when VG increased from −0.1, −1, −5, and then to −10 V, the height and width of the potential barrier and/or well increased from 0.018, 0.057, 0.075, and then to 0.129 eV (for the height) and from 0.35, 1.05, 1.53, and then to 3.18 μm (for the width), respectively (Fig. 2c). Such changes in the potential barrier and/or well demonstrate the controllability for the potential well in the vdW channel via the partial gating.
Following the study on the controllability of the potential barrier and/or well, we analyzed the carrier transport mechanism in the vdW channel of the PG-NDT device by investigating (i) the hole barrier height between the Pt drain/source and WSe2 channel, and (ii) the work function of WSe2 on h-BN via low-temperature electrical measurement and KPFM analysis, respectively (Fig. 2d). As the results based on the investigation, the previously mentioned hole barrier height of Pt-WSe2 junction and the work function of WSe2 on h-BN were predicted to be approximately 0.25 and 4.86 eV, respectively (“Methods” sections). Based on the obtained experimental values, the energy band diagrams in an equilibrium state before/after contacting Pt and WSe2 are predicted in Supplementary Fig. 5. Figure 2e explains the operation of the PG-NDT device in three different gate voltage regions (Operating Regions 1, 2, and 3). When the value of VG increases in the negative direction from VG = 20 V to the vicinity of VG = 0 V (Operating Region 1), the electron potential barrier formed by the positive VG becomes shallow in depth. In other words, because the potential barrier for holes in the middle of the vdW channel gets lower, the hole carriers, which are injected from the source, are collected more efficiently by the drain. This leads to an increase in ID. When the VG increases further in the negative direction from the vicinity of VG = 0 V to the vicinity of VG = −10 V (Operating Region 2), the hole potential well in the middle of the vdW channel becomes gradually deeper, consequently suppressing the collection of hole carriers and causing the abnormal decrease in ID. Beyond the vicinity of VG = −10 V, as VG continues to increase negatively (Operating Region 3), the probability of the hole carrier injection from the source increases significantly, overwhelming the suppression effect by the hole potential well in the middle of the vdW channel. Consequently, this causes ID to increase again. Further investigation of the NDT phenomena with respect to the width of the partial gate and the length of the vdW channel of the PG-NDT devices is provided in Supplementary Fig. 6. Meanwhile, as discussed in detail in Supplementary Fig. 7, the feasibility of this PG-NDT device toward MVL circuits was confirmed by implementing the ternary inverter, which has been demonstrated in many previous studies.
Controllability for the NDT phenomenon
The NDT phenomenon can be controlled in terms of the peak/valley currents and voltages by irradiating a light and adjusting the power and wavelength of the light (Fig. 3a). We irradiated the light with a power of 20 μW and a wavelength of 520 nm in the middle of the vdW channel of the PG-NDT device, following which we investigated the ID−VG and Gm−VG characteristics, where the negative Gm denotes the optoelectronic NDT (O-NDT) phenomenon (Fig. 3b). As provided in Supplementary Fig. 8, when VG increased in the negative direction from VG = 20 V to about VG = 0 V (Operating region 1), the potential well for the photo-generated electrons and the potential barrier for the photo-generated/injected holes decreased, resulting in an increased ID. Then, as VG increased further in the negative direction to about VG = −12 V, abnormal reduction in the ID was observed (Operating region 2), denoting the O-NDT phenomenon. This is because the potential well for the holes and the potential barrier for the electrons were formed, suppressing the collection of the carriers by the drain and source electrodes. Beyond the vicinity of VG = −13 V, ID increased again as VG continued to increase negatively (Operating region 3). The large negative VG is predicted to have increased significantly the probability of the hole injection from the source, consequently overwhelming the suppression effect by the potential well.
Following the investigation of the O-NDT phenomenon, as shown in Fig. 3c, d, we examined the dependency of the O-NDT phenomenon on the light power and wavelength by performing ID−VG characteristic measurements. As the light power increased from 2 to 20 and then to 43 μW, the peak/valley currents increased from 27.7/13.2 to 69.9/34.4 and then to 127/64.1 nA, and the peak/valley voltages decreased from 0.2/−12.2 to −0.9/−13.2 and then to −2.2/−15.4 V, respectively (Fig. 3c). This is because the number of photo-generated carriers increased as the light power increased, which subsequently negated the suppression effect of the potential barrier and/or well. Figure 3c bottom graphically illustrates the predicted operating principle of the PG-NDT device with negative VG under low- and high-light power conditions. Similarly, as shown in Fig. 3d, we investigated the O-NDT phenomenon with respect to three wavelengths of incident light (405, 520, and 655 nm). The peak/valley voltages and currents were extracted from the ID−VG curves in Fig. 3d, which shifted to the left and upward directions as the wavelength decreased from 655 to 405 nm. The peak/valley voltages were reduced from 10.6/0 (655 nm) to −14.1/−18.8 V (405 nm), and the corresponding current increased from 32/12.8 (655 nm) to 131/85.6 nA (405 nm). Ultraviolet–visible (UV–Vis) measurements were also performed to obtain information on the absorbance of WSe2 film (Supplementary Fig. 9), where the absorbance increased from 0.67 to 0.90 and then to 0.95 as the wavelength decreased from 655 to 520 and then to 405 nm. This change in the absorbance implies that: (i) the number of photo-generated electrons and holes increased as the wavelength of light decreased, and (ii) the photons with higher energy (=shorter wavelength) further energized the photo-generated electrons and holes. This supports the claim that more photo-generated carriers overcame the potential barrier and/or well under the shorter wavelength condition. Figure 3d bottom also graphically illustrates the predicted operating principle of the PG-NDT device with negative VG under high- and low-light wavelength conditions. Besides, in Supplementary Fig. 10, we investigated the NDT characteristics by changing the VD value. The results showed that a strategy changing VDD could not lead to the sufficient modulation of threshold voltages in the NDT phenomenon for inducing the multiple NDT phenomenon. Only ΔVpeak of 2.2 V was observed as the VDD increased from −5 mV to −2 V. On the other hand, the proposed strategy adjusting light wavelength enabled a much larger modulation of threshold voltages (ΔVpeak = 10 V at λ range of 520–655 nm and ΔVpeak = 13.9 V at λ range of 405–520 nm).
Ternary NAND/NOR gate using two-channel PG-NDT device
Subsequently, we implemented the double NDT phenomenon featuring two consecutive NDT phenomena by exploiting the controllability of the NDT phenomenon. As depicted in Fig. 4a, we fabricated the two-channel PG-NDT (2C-PG-NDT) device comprising two vdW channels (vdW channels I and II), which were formed on the same WSe2/h-BN heterostructure with a partially defined gate electrode (LCH = 20 μm and ratio of WPG/LCH = 25%). When lights with different powers and wavelengths are irradiated on the vdW channels, the vdW channel devices induce distinct O-NDT characteristic curves (I655nm for λ655nm, I520nm for λ520nm, and I405nm for λ405nm). The different drain currents following their own O-NDT characteristics are summed at the source (Isum = Iλ1 + Iλ2), thus causing the double O-NDT phenomenon. As shown in Fig. 4b, after the lights with wavelengths of 520 and 655 nm are irradiated on vdW channels I and II, the double O-NDT phenomenon was observed, where the first and second NDT phenomena appeared in the vicinity of 9.6 and 0.2 V, respectively.
Beyond the well-known application toward an MVL inverter, in this study, we designed and implemented an MVL NAND/NOR gate circuit. As depicted at the top of Fig. 4c, we propose a ternary NAND gate circuit comprising a diode-connected load transistor and two 2C-PG-NDT devices connected in series, where the gate and drain nodes of the load transistor are tied and the 2C-PG-NDT devices are based on the double O-NDT characteristic. The supply voltages and input voltages are applied to the source node of the load transistor (for the VDD), the source node of the 2C-PG-NDT device 2 (for the VSS), and the gate nodes of the 2C-PG-NDT devices 1 and 2 (for Vin1 and Vin2). Then, the output voltage (Vout) is measured at the output node, which is located between the load transistor and the two 2C-PG-NDT devices. Basically, the 2C-PG-NDT devices have specific resistances (RNDT“0”, RNDT“1”, or RNDT“2” for 2C-PG-NDT devices, respectively) according to the two input voltages (Vin1 and Vin2), and the resistance of the diode-connected load transistor (Rload) is determined mainly by the channel dimensions. When input voltages of approximately −10 V (logic “0”), 0 V (logic “1”), and 10 V (logic “2”) are applied to 2C-PG-NDT device, the device has three resistances as follows: RNDT“0” denoting a relatively high resistance, RNDT“1” denoting a relatively middle resistance, and RNDT“2” denoting a relatively low resistance, respectively. Here, we adjusted the resistance of the load transistor to have a similar value to that of RNDT“1” (Rload ≈ RNDT“1”). The resistance variations of the 2C-PG-NDT devices consequently facilitate the operation of the ternary NAND gate circuit using the voltage divider rule as follows. According to the combination of two input voltages of the 2C-PG-NDT devices (Vin1 and Vin2), as shown in Fig. 4d, the operation of the ternary NAND gate can be explained by dividing it into three cases. For case 1, the two input voltages, including at least one −10 V (logic “0”) are applied to the 2C-PG-NDT devices ({Vin1, Vin2} = {“0”, “0”}, {“0”, “1”}, {“1”, “0”}, {“0”, “2”}, or {“2”, “0”}). Here, the total resistance of the 2C-PG-NDT devices connected in series is always larger than that of the load transistor (Rload < RNDT“0” + RNDT“0”, RNDT“0”or“1” + RNDT“1”or“0”, or RNDT“0”or“2” + RNDT“2”or“0”), thus causing the output voltage to be higher than 0.5VDD (logic “2”). For case 2, the two input voltages excluding −10 V (logic “0”) and including at least one 0 V (logic “1”) are applied to the 2C-PG-NDT devices ({Vin1, Vin2} = {“1”, “1”}, {“1”, “2”}, or {“2”, “1”}). The total resistance of the 2C-PG-NDT devices is similar to that of the load transistor, causing the output voltage to be between 0.5VDD and 0.67VDD (logic “1”). For case 3, the two input voltages of 10 V (logic “2”) are applied to the 2C-PG-NDT devices ({Vin1, Vin2} = {“2”, “2”}), the total resistance of the 2C-PG-NDT devices connected in series is smaller than that of the load transistor (Rload > RNDT“2” + RNDT“2”), which causes the output voltage to be lower than 0.5VDD (logic “0”). For the ternary NOR gate, the circuit diagram and operating principle are described in detail in Supplementary Fig. 11. We then verified the previously mentioned operation of the ternary NAND/NOR gate circuits using a Cadence® Spectre® circuit simulator as follows. For the 2C-PG-NDT devices, the table-lookup-based models based on experimental data were developed in the Verilog-A language. The n-channel load transistor model was provided by the Cadence® Spectre® circuit simulator. Then, as depicted in the timing diagrams of Fig. 4e, −10.8, 0, and 9.6 V were, respectively, applied as the logic states “0”, “1”, and “2” to the input nodes indicated by Vin1 and Vin2. Voltages of 2 and 0 V were applied as the supply voltages of VDD and VSS, respectively. As a result of the application of the input voltages, the output voltages in the NAND/NOR gates appeared between 0.85 V/0.71 V and 0.85 V/0.79 V (for the logic state “0”), between 0.98 V/0.91 V and 1.05 V/0.99 V (for the logic state “1”), and between 1.17 V/1.24 V and 1.23 V/1.24 V (for the logic state “2”), respectively. Here, the operating speed of MVL NAND/NOR gates is predicted to be mainly affected by the gate capacitance of the PG-NDT and load devices49,50, and the power consumption will be determined by the operating currents, of which the operating currents of the NDT and load devices reported up to present are summarized in Supplementary Table 2 and Note 6.
Discussion
We reported a PG-NDT device featuring a controllable potential barrier and well, which were formed in the middle of the vdW channel by partially defining a gate region. The controllable potential barrier/well based on the partial gating enabled control of the collection of carriers by source/drain electrodes, and eventually induced the stable NDT phenomenon. We revealed the operating principle of the PG-NDT device by performing detailed analyses using 3D AFM, X-TEM, EDS, temperature-dependent current–voltage, and KPFM measurements. In particular, the strategy to expose the PG-NDT device to various lights with powers ranging from 2 to 43 μW and wavelengths ranging from 405 to 605 nm facilitated the precise control of the NDT phenomenon. Subsequently, by applying the light-based control technique of the NDT phenomenon to the 2C-PG-NDT device, we could realize the multiple NDT characteristic featuring two consecutive NDT phenomena. Finally, beyond the well-known application as a ternary logic inverter, ternary arithmetic logic circuits such as ternary NAND/NOR gates were designed, and their operating principles were verified by performing Cadence® Spectre® circuit simulations. Based on this research, in which we implemented the multiple NDT device and applied it to the development of MVL NAND/NOR gates, we provided the critical fundamental background for future studies on NDT-based MVL devices and circuits.
Methods
Fabrication of PG-NDT devices
The partially defined gate electrodes with a width of 4 μm were patterned on a 90-nm-thick SiO2 oxide layer on a heavily B-doped Si substrate using an optical lithography process, followed by the deposition of 5-nm-thick Ti and 15-nm-thick Au using an electron-beam evaporator. The h-BN and WSe2 layers were mechanically transferred onto the partially defined gate using a residue-free transfer method based on adhesion energy engineering (see Supplementary Fig. 1). Then, the source and drain electrodes were patterned on the h-BN/WSe2 heterostructure, followed by 10-nm-thick Pt contact and 50-nm-thick Au pad deposition. The distance between the two electrodes and the width of the electrodes were 20 and 10 μm, respectively.
Characterization of PG-NDT devices
AFM analysis and KPFM measurements were performed in an NX10 system (Park System Corp.). X-TEM measurements were conducted for the structural analysis of WSe2/h-BN/partially defined gate electrode regions using JEM ARM 200F. Raman analysis was performed at several positions on the WSe2/h-BN samples using a WITec micro-Raman spectrometer system with a frequency-doubled Nd-doped yttrium aluminum garnet (Nd-YAG) laser beam (532-nm laser excitation). Electrical measurements of the PG-NDT devices were conducted at room temperature using a Keysight B2912A under dark and illuminated conditions. The dot lasers with wavelengths of 405, 520, and 655 nm were used as the light source. The temperature-dependent electrical characteristics were investigated in a vacuum chamber (below 10−4 Torr) using a Keithley 4200 Semiconductor Parameter Analyzer. UV–Vis absorption spectra were obtained using a V-670 spectrophotometer (Jasco Inc.).
KPFM analysis
NX10 (Park Systems Corp.) AFM system was used to obtain contact potential difference (VCPD) on the surface of the PG-NDT device sample with respect to various gate voltages (VG). KPFM was performed in a non-contact mode in dark and ambient conditions, where the topography was obtained during the first scan and then VCPD distribution was recorded during the second scan. VG was applied through the back partial gate, and source and drain electrodes were grounded. A platinum/iridium (Pt/Ir)-coated Si tip was used and the tip was calibrated on a highly oriented pyrolytic graphite (HOPG) surface. The surface work function of the device samples was obtained from the contact potential difference (CPD) between the tip work function and the HOPG work function (ΦTip – ΦHOPG = VCPD), where the standard HOPG value of 4.6 eV was used.
Extraction of Schottky barrier height
To determine the Schottky barrier height between Pt source/drain electrodes and WSe2, a thermionic emission current equation for a Pt-WSe2-Pt junction was used as follows
where I0 is the saturation current, A is the effective area, A** is the Richardson constant, T is the temperature in Kelvin, q is the elementary charge, ΦB is the Schottky barrier height, kB is the Boltzmann constant, VDS is the voltage across the source and drain, and n is the ideality factor. When a reverse bias was applied, the \({\mathrm{exp}}\left( {\frac{{qV_{{\mathrm{DS}}}}}{{nk_BT}}} \right)\) term was ignorable and the above equation was consequently simplified as follows
Moving the T2 term to the left-hand side of the equation and taking the natural log on both sides, the following equation was obtained
Schottky barrier heights were extracted by plotting \({\mathrm{ln}}\left( {\frac{{I_0}}{{T^2}}} \right)\) as a function of \(\frac{q}{{k_{\mathrm{B}}T}}\) and finding the slope of the line.
Data availability
The data that support the findings of this study are available from the corresponding author upon request.
References
Shi, W., Cuo, Y. & Liu, Y. When flexible organic field‐effect transistors meet biomimetics: a prospective view of the internet of things. Adv. Mater. 31, 1901493 (2019).
Weiser, M. The computer for the 21st Century. Sci. Am. 265, 94–104 (1991).
Ashton, K. That ‘internet of things’ thing. RFID J. 22, 97–114 (2009).
Mattern, F. & Floerkemeier, C. in From Active Data Management to Event-Based Systems and More (eds. Sachs, K., Petrov, I. & Guerrero, P.) 242–259 (Springer Berlin Heidelberg, 2010).
Apte, P. et al. Future interconnect materials and system integration strategies for data-intensive applications. 7th Electronics System-Integration Technology Conference, Dresden, Germany (2018).
Ozer, E. et al. Multiple-valued logic buses for reducing bus ride, transitions and power in deep submicron technologies. Advanced Networking and Communications Hardware Workshop. (2005).
Ozer, E. et al. Multiple-valued logic buses for recuring bus energy in low-power systems. IEEE Proc. Comput. Digit. Technol. 153, 270–282 (2006).
Britnell, L. et al. Resonant tunnelling and negative differential conductance in graphene transistors. Nat. Commun. 4, 1794 (2013).
Zhao, Y. et al. Negative differential resistance in boron nitride graphene heterostructures: physical mechanisms and size scaling analysis. Sci. Rep. 5, 10712 (2015).
Lee, S., Lee, Y. & Kim, C. Extraordinary transport characteristics and multivalue logic functions in a silicon-based negative-differential transconductance device. Sci. Rep. 7, 11065 (2017).
Chen, J., Reed, M. A., Rawlett, A. M. & Tour, J. M. Large on-off ratios and negative differential resistance in a molecular electronic device. Science 286, 1550–1552 (1999).
Mishchenko, A. et al. Twist-controlled resonant tunnelling in graphene/boron nitride/graphene heterostructures. Nat. Nanotech. 9, 808–813 (2014).
Perrin, M. L. et al. Large negative differential conductance in single-molecule break junctions. Nat. Nanotech. 9, 830–834 (2014).
Choi, W. S. et al. Resonant tunnelling in a quantum oxide superlattice. Nat. Commun. 6, 7424 (2015).
Kim, Y. J. et al. Demonstration of complementary ternary graphene field-effect transistors. Sci. Rep. 6, 39353 (2016).
Huang, M. et al. Multifunctional high-performance van der Waals heterostructures. Nat. Nanotechnol. 12, 1148–1154 (2017).
Lim, J.-H. et al. Double negative differential transconductance characteristic: from device to circuit application toward quaternary inverter. Adv. Funct. Mater. 29, 1905540 (2019).
Lin, Y.-C. et al. Atomically thin resonant tunnel diodes built from synthetic van der Waals heterostructures. Nat. Commun. 6, 7311 (2015).
Kim, K.-H. et al. A multiple negative differential resistance heterojunction device and its circuit application to ternary static random access memory. Nanoscale Horiz. 5, 654–662 (2020).
Wang, Y. et al. Light induced double ‘on’ state anti-ambipolar behavior and self-driven photoswitching in p-WSe2/n-SnS2 heterostructures. 2D Mater. 4, 025097 (2017).
Shim, J. et al. Phosphorene/rhenium disulfide heterojunction-based negative differential resistance device for multi-valued logic. Nat. Commun. 7, 13413 (2016).
Nourbakhsh, A., Zubair, A., Dresselhaus, M. S. & Palacios, T. Transport properties of a MoS2/WSe2 heterojunction transistor and its potential for application. Nano Lett. 16, 1359–1366 (2016).
Shim, J. et al. Light-triggered ternary device and inverter based on heterojunction of van der Waals materials. ACS Nano 11, 6319–6327 (2017).
Shim, J. et al. Electronic and optoelectronic devices based on two-dimensional materials: from fabrication to application. Adv. Electron. Mater. 3, 1600364 (2017).
Wang, L. et al. One-dimensional electrical contact to a two-dimensional material. Science 342, 614–617 (2013).
Jo, S.-H. et al. A high-performance WSe2/h-BN photodetector using a triphenylphosphine (PPh3)-based n-doping technique. Adv. Mater. 28, 4824–4831 (2016).
Shim, J. & Park, J.-H. Optimization of graphene-MoS2 barristor by 3-aminopropyltriethoxysilane (APTES). Org. Electron 33, 172–177 (2016).
Mueller, T. & Malic, E. Exciton physics and device application of two-dimensional transition metal dichalcogenide semiconductors. NPJ 2D Mater. Appl. 2, 29 (2018).
Zribi, J. et al. Strong interlayer hybridization in the aligned SnS2/WSe2 hetero-bilayer structure. NPJ 2D Mater. Appl. 3, 27 (2019).
Lee, C.-H. et al. Atomically thin p–n junctions with van der Waals heterointerfaces. Nat. Nanotech. 9, 676–681 (2014).
Hong, X. et al. Ultrafast charge transfer in atomically thin MoS2/WS2 heterostructures. Nat. Nanotech. 9, 682–686 (2014).
Choi, C. et al. Enhanced interlayer neutral excitons and trions in trilayer van der Waals heterostructures. NPJ 2D Mater. Appl. 2, 30 (2018).
Shim, J. et al. Recent progress in Van der Waals (vdW) heterojunction-based electronic and optoelectronic devices. Carbon 133, 78–89 (2018).
Lim, J. Y. et al. Van der Waals junction field effect transistors with both n- and p-channel transition metal dichalcogenides. NPJ 2D Mater. Appl. 2, 37 (2018).
Kremser, M. et al. Discrete interactions between a few interlayer excitons trapped at a MoSe2–WSe2 heterointerface. NPJ 2D Mater. Appl. 4, 8 (2020).
Kim, S. et al. Gate-switchable rectification in isotype van der Waals heterostructure of multilayer MoTe2/SnS2 with large band offsets. NPJ 2D Mater. Appl. 4, 15 (2020).
Novoselov, K. S., Mishchenko, A., Carvalho, A. & Castro Neto, A. H. 2D materials and van der Waals heterostructures. Science 353, aac9439 (2016).
Seo, S. et al. Artificial optic-neural synapse for colored and color-mixed pattern recognition. Nat. Commun. 9, 5106 (2018).
Chaves, A. et al. Bandgap engineering of two-dimensional semiconductor materials. NPJ 2D Mater. Appl. 4, 29 (2020).
Seo, S. et al. Recent progress in artificial synapses based on two-dimensional van der Waals materials for brain-inspired computing. ACS Appl. Electron. Mater. 2, 371–388 (2020).
Liang, S.-J., Cheng, B., Cui, X. & Miao, F. Van der Waals heterostructures for high‐performance device applications: challenges and opportunities. Adv. Mater. 32, 1903800 (2020).
Seo, S. et al. Artificial van der Waals hybrid synapse and its application to acoustic pattern recognition. Nat. Commun. 11, 3936 (2020).
Kinoshita, K. et al. Dry release transfer of graphene and few-layer h-BN by utilizing thermoplasticity of polypropylene carbonate. NPJ 2D Mater. Appl. 3, 22 (2019).
Shim, J. et al. Polarity control in a single transition metal dichalcogenide transistor for homogeneous complementary logic circuits. Nanoscale 11, 12871–12877 (2019).
Paul, A. K. et al. Photo-tunable transfer characteristics in MoTe2–MoS2 vertical heterostructure. NPJ 2D Mater. Appl. 1, 17 (2017).
Jung, K.-S. et al. Double negative differential resistance device based on hafnium disulfide/pentacene hybrid strcutrue. Adv. Sci. 7, 200991 (2020).
Chen, Y.-H. et al. Oxidized-monolayer tunneling barrier for strong Fermi-level depinning in layered InSe transistors. NPJ 2D Mater. Appl. 3, 49 (2019).
Kim, S. et al. Ferroelectrid polymer-based artificial synapse for neuromorphic computing. Nanoscale Horiz. 6, 139–147 (2021).
Lei, L. et al. High-speed graphene transistors with a self-aligned nanowire gate. Nature 467, 305–308 (2010).
Lee, J. et al. Ion gel-gated polymer thin-film transistors: operating mechanism and characterization of gate dielectric capacitance, switching speed, and stability. J. Phys. Chem. C. 113, 8972–8981 (2009).
Acknowledgements
This research was supported by the Samsung Research Funding & Incubation Center of Samsung Electronics under Project Number SRFC-MA1701-02.
Author information
Authors and Affiliations
Contributions
S.S., J.K., J.-W.C., and J.-H.P. designed the experiments and analyzed the data. J.-H.P. supervised the research. All authors have discussed the results and commented on the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Seo, S., Koo, J., Choi, JW. et al. Controllable potential barrier for multiple negative-differential-transconductance and its application to multi-valued logic computing. npj 2D Mater Appl 5, 32 (2021). https://doi.org/10.1038/s41699-021-00213-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41699-021-00213-4
This article is cited by
-
Charge transfer mechanism for realization of double negative differential transconductance
npj 2D Materials and Applications (2024)
-
Two-dimensional materials based on negative differential transconductance and negative differential resistance for the application of multi-valued logic circuit: a review
Carbon Letters (2023)
-
Multivalued Logic Inverter Using Multiple Channel Field Effect Transistor (MCFET)
Silicon (2022)