Article | Open

Smart window coating based on F-TiO2-KxWO3 nanocomposites with heat shielding, ultraviolet isolating, hydrophilic and photocatalytic performance

Received:
Accepted:
Published online:

Abstract

A series of smart window coated multifunctional NIR shielding-photocatalytic films were fabricated successfully through KxWO3 and F-TiO2 in a low-cost and environmentally friendly process. Based on the synergistic effect of KxWO3 and F-TiO2, the optimal proportion of KxWO3 to F-TiO2 was investigated and the FT/2KWO nanocomposite film exhibited strong near-infrared, ultraviolet light shielding ability, good visible light transmittance, high photocatalytic activity and excellent hydrophilic capacity. This film exhibited better thermal insulation capacity than ITO and higher photocatalytic activity than P25. Meanwhile, the excellent stability of this film was examined by the cycle photocatalytic degradation and thermal insulation experiments. Overall, this work is expected to provide a possibility in integrating KxWO3 with F-TiO2, so as to obtain a multifunctional NIR shielding-photocatalytic nanocomposite film in helping solve the energy crisis and deteriorating environmental issues.

Introduction

Today, energy crisis and deteriorating environmental issues are posing serious threats to the sustainable development of human society. Thus, an increasing number of researches have focused on utilizing green techniques to deal with these aforementioned concerns in the past years1,2,3,4,5. As a critical component of buildings, windows can lose energy easily. Therefore, energy-efficient window coatings are considered to be the important step for reducing heat transfer between the indoor and outside environments. As a novel near-infrared (NIR) shielding material, the tungsten bronze (MxWO3), which is WO3 doped with monovalent ions such as K+, Na, NH4+ and others, has attracted great attention in recent years6,7. Compared with some transparent thermal insulation coatings like noble metals (Ag, Au)8, black compounds (ruthenium dioxides, rhenium trioxides)9, rare-earth hexaborides (lanthanum hexaborides)10,11, and semiconductor oxides (ITO, ATO, AZO, etc.)12,13,14, the NIR shielding ability and visible (Vis) transmittance of tungsten oxides can be remarkably superior due to the high free electron density, which can be utilized to produce localized surface plasma resonance11,15. Lately, our group have reported that cesium tungsten oxides (CsxWO3) powders could be prepared by a water controlled-release solvothermal process with CsOH and WCl6 as raw materials, and it could exhibit excellent visible transparency and broad waveband absorption of 800 to 15,000 nm16,17. However, these raw materials are not environmentally friendly because of the easy hydrolysis of WCl6 and the volatilization of HCl18. To overcome this drawback, the one-dimensional potassium-doped tungsten bronze (KxWO3) powders were successfully synthesized with K2WO4 and K2SO4 through the hydrothermal process. The products could shield the NIR light with wavelength λ > 1000 nm, and this excellent heat shielding property implies that the KxWO3 might be the potential candidate for the smart window coated materials19.

If a smart window coating could be developed to not only shield the NIR but also degrade harmful pollutants, it would have a huge impact on deteriorating environmental issues and present self-cleaning effect simultaneously. Owing to photocatalytic and hydrophilic properties, semiconductor photocatalysts are widely and frequently employed to purify air and water contaminants20,21. Among various semiconductor photocatalysts, titanium dioxide (TiO2) is the most suitable photocatalyst for widespread environmental applications because of its long-term stability against photocorrosion, excellent photocatalytic activity and strong absorption of harmful ultraviolet (UV) light22,23,24,25,26. Due to the fact that a photocatalytic reaction occurs at the interface between catalyst surfaces and organic pollutants, it is highly feasible that the photocatalytic activity of TiO2 is strongly dependent on its surface properties27,28. Based on this speculation, surface-fluorinated TiO2 (F-TiO2) has been extensively investigated for its wonderful photocatalytic activity, which could be attributed to the enhanced generation of mobile free •OH radicals on the surface of F-TiO229. Thus, F-TiO2 might be a promising photocatalyst to solve the environmental pollution concerns by relying on its highly efficient solar-light-driven photocatalytic activity30.

In our recent research, CsxWO3/ZnO nanocomposite was prepared as a smart coating for photocatalytic environmental cleanup and heat insulation31. Despite numerous advantages of this film, the less environmental friendliness of the preparation process and the instability of ZnO are in urgent need to be solved32,33. In this work, a series of multifunctional NIR shielding-photocatalytic nanocomposite films were fabricated successfully through F-TiO2 and KxWO3. In these smart coatings, KxWO3 plays a part in shielding most of NIR light and holding high Vis light transparency, while F-TiO2 acts as both a photocatalyst to degrade harmful organic pollutants and a barrier to shield harmful ultraviolet light, which makes up the shortage of KxWO3 in the UV region. It’s worth mentioning that the KxWO3 nanorods were synthesized with Na2WO4 as tungsten source instead of K2WO4, which is considered as a lower-cost way than previously reported method of preparing tungsten bronze powders19,34. Furthermore, the heat-shielding and photocatalytic property of F-TiO2-KxWO3 nanocomposite films were evaluated and compared with that of ITO or P25 film to find out the optimal ratio of KxWO3 to F-TiO2 with a synergistic effect.

Results and Discussion

As shown in Fig. 1, XRD analysis has been employed for analyzing the crystalline phase of samples. The reflection in Fig. 1a matches best with the single anatase TiO2 (JCPDS 21-1272) phase, while the main peaks at 2θ values of 13.8o, 23.6o and 27.8o can be indexed respectively to (100), (002) and (200) crystal planes, which are readily indexed to the pure potassium tungsten bronze (K0.26WO3; JCPDS83-1593), as displayed in Fig. 1b. Furthermore, with the increasing content of F-TiO2, the intensities of the TiO2 peaks are increased obviously (Fig. 1c–g), revealing that FT-KWO nanocomposites are obtained successfully during the hydrothermal process. Meanwhile, peaks related to other phases are not observed in the synthesized samples, indicating that the F-TiO2 have not reacted with the KxWO3.

Figure 1
Figure 1

XRD patterns of pure (a) F-TiO2, (b) KxWO3 and different FT-KWO nanocomposites: (c) 3FT/KWO, (d) 2FT/KWO, (e) FT/KWO, (f) FT/2KWO, (g) FT/3KWO.

The morphology of the as-prepared samples was characterized by SEM, which is shown in Fig. 2. As shown in Fig. 2a,b, the pure F-TiO2 is nanoparticles with relatively uniform size and the as-prepared KxWO3 powders exhibit smooth surface, regular nanorods with size of about 300–400 nm, which are corresponding to that of products synthesized with K2WO4 and K2SO419. Figure 2c shows the SEM image of KxWO3 samples after the introduction of the F-TiO2, and it could be clearly seen that F-TiO2 particles are attached to the surface of KxWO3 nanorods, indicating the intimate contact between F-TiO2 and KxWO3. The inset in Fig. 2c shows the SEM image of FT/2KWO film at 45o, and the thickness of the film can be calculated to be about 3.37 μm, according to the equation: t = t’ × sin θ. Where t’ is the thickness shown in SEM image (t’ = 2.38 μm) and θ is the view angle (θ = 45o). In addition, EDX analysis confirms the distribution of Ti, O, F elements in F-TiO2 samples and K, W, O elements in KxWO3 samples as shown in Fig. 2d,e, respectively. As for FT/2KWO nanocomposites (Fig. 2f), it reveals the coexistence of Ti, O, F, K, and W elements as expected, which also indicates the existence of F-TiO2 and KxWO3 in FT/2KWO nanocomposites. Furthermore, according to EDX quantification (insert Fig. 2f), the atom percentages of Ti and W for the as-synthesized FT/2KWO nanocomposites are 9.74% and 6.62%, and the atom ratio of Ti to W is approximately 1.47, which is very close to the nominal value (Ti: W = 1.53). In addition, the Ti: W ratios are corresponding with the nominal ratios in all FT-KWO nanocomposites as displayed in Fig. S1, indicating that the elementary composition is well controlled by the experimental conditions.

Figure 2
Figure 2

SEM images of (a) F-TiO2, (b) KxWO3, (c) FT/2KWO nanocomposites; EDX spectra of (d) F-TiO2, (e) KxWO3, (f) FT/2KWO nanocomposites. The insets in (c) shows SEM image of FT/2KWO films (at 45o angle view).

To further obtain the microscopic morphology and structure information, the TEM and HRTEM analysis of as-synthesized FT/2KWO nanocomposites have been performed, as shown in Fig. 3. The TEM images of FT/2KWO nanocomposites (Fig. 3a,b) show the specific rod-like morphology with some nanoparticles attached, which is in accordance with SEM results. Moreover, The HRTEM image of the magnified view is given in Fig. 3c. The distance of 0.38 nm and 0.19 nm between the adjacent lattice fringes can be assigned to the (002) plane of hexagonal KxWO3 and the (200) plane of anatase TiO2 nanocrystals, respectively. Obviously, the FT/2KWO nanocomposites are formed with favourable nanosizd interfacial contact so as to exhibit multifunctional properties of NIR shielding and photocatalytic degradation.

Figure 3
Figure 3

(a) Low-, (b) High-magnification TEM images and (c) HRTEM images of as-synthesized FT/2KWO nanocomposites.

The chemical composition of the FT/2KWO nanocomposite particles was also examined by XPS. The full range XPS spectra are presented in Fig. S2a. Peaks at binding energies corresponding to Ti, O, F, K, and W are clearly distinguished and no extra elements except carbon can be found in the spectra. The W4f core-level XPS spectra of the as-prepared FT/2KWO samples exhibit detailed information on the chemical state of core level tungsten, as shown in Fig. S2b. There are two spin-orbit doublets in this spectrum, which is attributed to W4f7/2 and W4f5/2: the peaks at 35.8 eV and 37.9 eV are attributed to W6+, while the peaks at 34.8 eV and 36.9 eV are assigned to W5+, which reaches a good agreement with the reported results. Meanwhile, the atomic contents of Ti and W in FT/2KWO were calculated from XPS and found to be 55.23 at. % and 36.21 at. %, corresponding to the nominal value (Ti: W = 1.53). It is suggested that the non-stoichiometric potassium tungsten bronzes are reduced compounds, and the co-existence of W5+ and W6+ is the necessary condition for the NIR shielding performance31.

To study optical properties of the samples, the transmittance spectra of the as-prepared films are shown in Fig. 4. For the pure KxWO3 film (Fig. 4g), a great NIR shielding performance at the range of 780 to 2500 nm was observed, which could be closely related to the plasmon resonance of free electrons, interband transition and small polarons35. However, the visible light transparency and absorption of ultraviolet region (see inset in Fig. 4) are defective. On the contrary, these phenomena above are absent in the case of the film of pure TiO2 displayed in Fig. 4a, which exhibits no NIR shielding ability but excellent ultrviolet light absorption (see inset in Fig. 4) and high visible light transparency capability as a result of the narrow band gap of TiO2. As expected, all of the FT-KWO nanocomposite films retain all advantages of TiO2 and KxWO3 films in the range of UV, Vis and NIR. The inheritance of NIR absorption capability of composite could be attributed to the use of soft chemical method in synthesizing FT-KWO nanocomposite films in which the reduced W5+ ion was preserved. Specifically, with an increase in the KxWO3 content, the NIR shielding property becomes more pronounced while the visible light transmittance and UV shielding capability decreased. Even so, there will be a FT-KWO nanocomposite film with an appropriate mass ratio of F-TiO2 to KxWO3, exhibiting a great synergistic effect on blocking NIR and UV light as well as transmitting most of visible light.

Figure 4
Figure 4

Transmittance spectra of (a) pure F-TiO2, different FT-KWO nanocomposites: (b) 3FT/KWO, (c) 2FT/KWO, (d) FT/KWO, (e) FT/2KWO, (f) FT/3KWO and (g) pure KxWO3 films. The inset shows the absorption spectra of different powders with the wavelength from 200 nm to 420 nm.

On the basis of the aforementioned optical properties of FT-KWO nanocomposite films, it is reasonable to suggest that these films show great potential for application as NIR shielding films. A thermal insulation experiment has been carried out in a sealed box. Figure 5 exhibits the inner temperature variation upon irradiation time and cooling time, and the temperature variations between the initial and final temperature are listed in Table S1. As shown in Fig. 5a, it’s obvious that the temperature increases significantly with irradiation time when the box is covered with blank or F-TiO2 coated glass, which proves that the F-TiO2 film has no NIR shielding capacity as displayed in Fig. 4a. Notably, the heating rates of glasses coated with FT-KWO nanocomposites are much lower than those of box covered with the blank or F-TiO2 coated glass, and the heating rate inside the box decreased distinctly with an increase in the KxWO3 content. For example, within 60 min irradiation, the temperature variation of box covered with 2FT/KWO nanoparticle film coated glass is 11.5 °C, while that of box covered with FT/2KWO film coated glass is depressed to 10.2 °C. In addition, the temperature variation curves with cooling time (Fig. 5b) show similar tendency as discussed above, that is to say, all of the FT-KWO nanocomposite films show good thermal insulation performance. Moreover, the temperature variation between the initial and final temperature slows down with the increasing content of KxWO3, as displayed in Table S1. The relatively slow heating rates during the heating and cooling time indicate the FT-KWO nanocomposite films have great thermal insulation capacity. The ITO glasses are widely used and well-known as effective NIR shielding material, as a control, the simulated experiment was carried out by irradiating the sealed box covered by ITO, FT + 2KWO (mechanically mix F-TiO2 and KxWO3), FT@2KWO (F-TiO2 film coating on the top of KxWO3 film) and 2KWO@FT (KxWO3 film coating on the top of F-TiO2 film) coated glass, respectively, and the temperature changes inside the boxes are plotted in Fig. S3a. By comparison, the box covered with the FT/2KWO film coated glass exhibited a slight lower temperature gradient than the box covered with other coated glasses both during the period of heating (Fig. S3a) and cooling (Fig. S3b). This phenomenon is corresponding to the transmittance spectra inserted in Fig. S3a. The results indicate superior thermal insulation capacity and potential practical application of the FT-KWO nanocomposite film.

Figure 5
Figure 5

The inner temperature dependence on (a) irradiation time and (b) cooling time curves of sealed box covered with different films coated glass.

In order to confirm the photocatalytic activities of FT-KWO nanocomposite films, the degradation of MO by various films was carried out under the irradiation of UV light. As shown in Fig. 6a, F-TiO2 film exhibited high photocatalytic activity and 98% of the initial MO decreased after 80 min, whereas the KxWO3 film shows almost no effect on the degradation. Fortunately, these nanocomposite films are highly efficient for photocatalytic degradation of organic pollutant and the photocatalytic activity will be enhanced with the increase of F-TiO2 content in FT-KWO nanocomposites. For example, about 87% of the initial MO molecules are decomposed by the 3FT/KWO nanocomposite film, while in comparison, only 73% by the FT/3KWO film within 80 min. Based on previous studies, the degradation of dyes can be ascribed to a pseudo-first order reaction with a Langmuir–Hinshelwood model when the initial concentration of dye solution is small: ln (C0/C) = kt36. Where C is the concentration of MO after t min degradation, C0 is the initial concentration of MO, and k is the first-order reaction rate constant. Figure 6b exhibits the plots of ln (C0/C) versus irradiation time. Unusually, the FT/2KWO film exhibits similar photocatalytic activity to FT/KWO film where the k of FT/KWO is only about 1.05 times than that of FT/2KWO. Meanwhile, considering the temperature variation curves displayed in Fig. 5, the thermal insulation capacity of FT/2KWO film has gained a noticeable improvement than that of FT/KWO film. In other words, the FT-KWO film shows the best multifunctional properties when the mass ratio of F-TiO2 to KxWO3 is 1:2. To further investigate the advantages of FT-KWO nanocomposite film, as a comparison, the photocatalytic activities of P25, FT + 2KWO, FT@2KWO, 2KWO@FT and F-TiO2’ (where the F-TiO2 content in this film is equal to that of FT/2KWO film) films were measured under the same condition. As displayed in Fig. S4, the photocatalytic activity sequence of these films is FT/2KWO ~ P25 > FT + 2KWO > F-TiO2’ ~ FT@2KWO > 2KWO@FT and the enhancement of the photocatalytic activity could be attributed to the close interfacial contact and strong interaction between F-TiO2 and KxWO3 in FT/2KWO film. Besides, the introduction of KxWO3 with excellent electronic conductivity can promote the photogenerated electron transport to the surface of the composite more easily, thus inhibiting the recombination between photogenerated electrons and holes34,37,38. However, when it comes to FT + 2KWO film and others, the F-TiO2 and KxWO3 are independent (see SEM image inset Fig. S4) to generate nearly no synergistic effect. It is abnormal that only 53% of the initial MO molecules are decomposed by 2KWO@FT nanocomposite film within 120 min, which might be attributed to the covered surface of F-TiO2 limits the photocatalytic reaction to some extent39. In conclusion, these results mentioned above further confirm that the FT/2KWO nanocomposite film is effective for photocatalytic degradation of organic pollutant and very promising for practical application in smart window.

Figure 6
Figure 6

(a) Variation of MO concentration against irradiation time using F-TiO2 film, FT-KWO nanocomposite films with various KxWO3 contents and pure KxWO3 film under ultraviolet light irradiation and (b) plots of ln (C0/C) versus irradiation time for MO representing the fit using a pseudo-first-order reaction rate.

In consideration of the practical application of these nanocomposite films, the photocatalytic stability of the as-prepared FT/2KWO nanocomposite film was further investigated by the cycle experiment. As shown in Fig. S5a, the photocatalytic activity of the FT/2KWO nanocomposite film remains still unreduced after four consecutive cycles, thus indicating the good stability of the film during the photocatalytic experiment. Furthermore, the thermal insulation capacity of the FT/2KWO film after the fourth photocatalytic experiment was investigated and exhibited in Fig. S5b. It is clear that the temperature variation of box is about 10.5 °C (Fig. S5b-2) when it was covered with the FT/2KWO film coated glass after the fourth photocatalytic experiment, which is slightly higher than that of new FT/2KWO film coated glass (Fig. S5b-3), but much lower than that of blank glass (Fig. S5b-1). It thus indicates the great reusability of the FT-KWO nanocomposite films.

To identify the surface hydrophilic properties of the nanocomposite films, the contact angle (CA) value of the as-prepared FT/2KWO film was measured and compared with that of pure TiO2, KxWO3 film, as shown in Fig. 7. Notably, the CA value of KxWO3 film (CA = 35.48) is significantly higher than that of F-TiO2 film (CA = 14.62), which indicates the F-TiO2 film has good hydrophilic property. Meanwhile, the CA value of FT/2KWO film (CA = 13.96) has not been affected by the introduction of KxWO3 and the similar CA values between F-TiO2 film and FT/2KWO film reveal the hydrophilic nature of prepared FT/2KWO film. Interestingly, the CA value of FT/2KWO film decreased to 7.64° after the fourth photocatalytic experiment, as displayed in Fig. 7d. This phenomenon could be attributed to the photoinduced hydrophilicity caused by reconstruction of surface hydroxyl groups40,41. The above results confirm the FT/2KWO film is advantageous for applications in antifogging and self-cleaning coatings.

Figure 7
Figure 7

Contact angle of a water drop in air on new (a) F-TiO2, (b) KxWO3, (c) FT/2KWO films and (d) FT/2KWO film after the fourth photocatalytic experiment.

A working model illustrating the multifunctionality of the FT-KWO and F-TiO2 coated window is summarized in Fig. 8. Obviously, this smart window plays different roles in various conditions. In summer days, the FT-KWO film side towards the outside; with the irradiation of the solar light, the smart window can not only block most of the NIR lights for heat preservation and keep cool indoor, but also isolate harmful UV light and transmit Vis light. In winter days, this window should be rotated 180° to make the FT-KWO film side towards the inside. In this case, the smart window not only reduces heat loss from inside to outside, but also blocks UV light and transmits Vis light effectively. Meanwhile, the high hydrophilic capacity can control the production of water vapour on the window and enhance the visibility availably. To sum up, this smart window will minimize the usage of air conditioning and heaters to control the redundant electricity consumption and promote the solution of energy crisis. In addition, both sides will absorb UV light to motivate photocatalytic reaction owing to the existence of F-TiO2, so as to degrade the harmful organic air pollutants and help solve the environmental issues subtly.

Figure 8: The working model of the FT-KWO and F-TiO2 coated window applied to different conditions.
Figure 8

In summary, the F-TiO2-KxWO3 multifunctional nanocomposites have been fabricated successfully through a low-cost and eco-friendly method. Moreover, the FT-KWO films exhibited excellent multifunctional performance of NIR, UV light insulation, Vis transparency and photocatalytic activity. A competitive relation was observed between F-TiO2 and KxWO3: the photocatalytic activity will be decreased while the thermal insulation performance improved with the increase of KxWO3 content in FT-KWO nanocomposite films. As the optimal proportion of KxWO3 to F-TiO2, the FT/2KWO nanocomposite film shows a significant multifunctional property of outstanding NIR, UV light shielding performance, high photocatalytic activity on degradation of harmful organic pollutants and excellent hydrophilic capacity. It is worth mentioning that its thermal insulation capacity is better than that of ITO, while the photocatalytic activity is surpassing P25. Therefore, FT-KWO nanocomposite film could have great potential applications as smart windows coating material, so as to help solve the energy crisis and deteriorating environmental issues in a convenient way.

Methods

Preparation of KxWO3 nanorods

KxWO3 nanorods were synthesized on the basis of a procedure reported previously. All reagents were of analytical grade and used without further retreatment. Specifically, 1.6493 g Na2WO4·2H2O and 1.7424g K2SO4 were dissolved in 50 ml deionized water under magnetic stirring followed by adding 3 mol/L HCl to adjust pH to 1.5. After that, the resultant solution was transferred into a dried Teflon-lined autoclave with 100 mL internal volume and kept it at 200 °C for 24 h. After natural cooling to room temperature, the intermediate products were obtained after being washed with water and ethanol for three times respectively and dried at 50 °C overnight. Finally, a certain amount of as-prepared samples was reduced in H2 (5 vol %)/N2 atmosphere at 500 °C for 1 h to obtain the potassium tungsten bronze.

Preparation of FT-KWO nanocomposites

The as-prepared KxWO3 nanorods were redispersed via the assist of ultrasonication in 30 mL deionized water to obtain the homogeneous suspension. Then, 0.0713g NH4HF2 and 7.5 ml absolute ethyl alcohol with 1.71 ml tetrabutyl titanate (TBOT) were added dropwise to the suspensions under vigorous stirring for 30 min. Finally, the above suspensions were transferred into 50 mL Teflon-lined autoclaves and maintained at 150 °C for 10 h. After this hydrothermal reaction, the suspensions were centrifuged at 17000 rpm followed by washing with distilled water and ethanol twice, and then dried in an oven at 80 °C for 2 h. The nominal contents of KxWO3 additives were 25 wt.%, 33 wt.%, 50 wt.%, 67 wt.% and 75 wt.%, respectively for the FT-KWO nanocomposites. These samples are labelled as 3FT (F-TiO2)/KWO (KxWO3), 2FT/KWO, FT/KWO, FT/2KWO, and FT/3KWO, respectively. For comparison, pure F-TiO2 and KxWO3 were synthesized under the same condition.

Preparation of FT-KWO nanocomposite films

The NIR shielding and photocatalysis properties of F-TiO2-KxWO3 nanocomposites were evaluated by coating them onto quartz glass substrates (4 cm*4 cm*1 mm). In a typical film synthesis process, 0.2 g samples were dispersed into a mixed solution with 1.24 g collodion and 1.33 g absolute ethyl alcohol under magnetically stirring, thus forming homogeneous colloidal dispersions. Subsequently, the above slurries were spin-coated on the quartz glass substrates at 2500 rpm for 60 s, rinsed with absolute ethyl alcohol and dried at 60 °C for 30 min. For comparison, the P25, ITO and blank films were prepared under the identical conditions. In addition, the synthesis process of other films was presented in the supporting information.

Characterization

The phase purity of samples was analyzed by X-ray powder diffraction (XRD) using a Bruker D2 PHASER X-ray diffractometer with graphite monochromator using Cu Kα radiation (λ = 1.54184 Å) at room temperature. The morphology of the sample and the energy dispersive X-ray spectroscopy (EDS) spectrum were detected by field emission scanning electron microscopy (FESEM, Hitachi, 30 S-4800). Moreover, the transmittance of films was measured with a Perkin Elmer 950 spectrometer. Besides, transmission electron microscopy (TEM) and high-resolution transmission electron microscopy (HRTEM) images were collected on an F30 S-TWIN electron microscope (Tecnai G2, FEI Company). X-ray photoelectron spectroscopy (XPS, PHI-5702, Physical Electronics) was performed using a monochromated Al Ka irradiation. The chamber pressure was ~3 × 10−8 Torr under testing conditions. The surface hydrophilic properties of the as-prepared films were characterized by detecting the water contact angle measured by a contact angle meter (JC2000C) with 4 μL water droplet under ambient conditions.

Evaluation of NIR shielding property

To evaluate the thermal insulation properties of FT-KWO nanocomposite films, a simulated room was built with a sealed plastic box (11 cm*11 cm*11 cm) covered with different films coated glasses under the irradiation of a 275 W infrared lamp. The experiments were carried out at the room temperature of 25 °C and temperature variation was monitored by a thermodetector with four thermocouples every ten minutes. Meanwhile, the heat preservation performance of these films was evaluated in the same plastic box without the irradiation of infrared lamp, but the glasses were rotated 180° to make the FT-KWO film side toward the inside with the initial temperature being 40 °C.

Evaluation of photocatalytic activity

The photocatalytic activities of the FT-KWO nanocomposite films were evaluated by measuring the degradation ratio of methyl orange (MO). The initial concentration of MO solution was 10 mg/L−1, and the quartz glass substrate coated with FT-KWO nanocomposite film was immersed in 5 mL MO solution. A 500 W high pressure Hg lamp was employed for the ultraviolet irradiation source and positioned 10 cm away from the reactor to trigger the photocatalytic reaction. In addition, a certain volume of MO solution was withdrawn at selected times and analysed by measuring the light absorption of the clear solution at 464 nm (λmax for MO solution) using a spectrophotometer (LG-722SP).

Additional Information

How to cite this article: Liu, T. et al. Smart window coating based on F-TiO2-KxWO3 nanocomposites with heat shielding, ultraviolet isolating, hydrophilic and photocatalytic performance. Sci. Rep. 6, 27373; doi: 10.1038/srep27373 (2016).

References

  1. 1.

    , , , & Facet-Dependent Photocatalytic Properties of TiO2-Based Composites for Energy Conversion and Environmental Remediation. Chem Sus Chem 7, 690–719 (2014).

  2. 2.

    , & Domestic and overseas manufacturing scenarios of silicon-based photovoltaics: Life cycle energy and environmental comparative analysis. Solar Energy 105, 669–678 (2014).

  3. 3.

    et al. Monoclinic dibismuth tetraoxide: A new visible-light-driven photocatalyst for environmental remediation. Applied Catalysis B: Environmental 176–177, 444–453 (2015).

  4. 4.

    , , , & Reaction temperature controlled selective hydrogenation of dimethyl oxalate to methyl glycolate and ethylene glycol over copper-hydroxyapatite catalysts. Applied Catalysis B: Environmental 162, 483–493 (2015).

  5. 5.

    , & Energy crisis, greenhouse gas emissions and sectoral growth reforms: repairing the fabricated mosaic. Journal of Cleaner Production 112, Part 5, 3657–3666 (2016).

  6. 6.

    , , & Simple route to (NH4)(x)WO3 nanorods for near infrared absorption. Nanoscale 4, 3394–8 (2012).

  7. 7.

    , , & Effects of Crystallization Atmospheres on the Near-Infrared Absorbtion and Electroconductive Properties of Tungsten Bronze Type MxWO3 (M = Na, K). Journal of the American Ceramic Society 95, 1634–1639 (2012).

  8. 8.

    & Optical properties of metal clusters. Springer Ser. Mat. Sci 25 (1995).

  9. 9.

    , , & Inventors; Sumitomo Metal Mining Company, Limited, assignee. Coating solution for a heat-ray shielding film and a process for forming a heat-ray shielding film by employing the same. United States patent US 5,840,364. 1998 Nov 24.

  10. 10.

    , & Absorption and scattering of near-infrared light by dispersed lanthanum hexaboride nanoparticles for solar control filters. Journal of Materials Research 25, 510–521 (2010).

  11. 11.

    & Near Infrared Absorption of Tungsten Oxide Nanoparticle Dispersions. Journal of the American Ceramic Society 90, 4059–4061 (2007).

  12. 12.

    , & Fabrication of superhydrophobic and heat-insulating antimony doped tin oxide/polyurethane films by cast replica micromolding. Journal of Colloid and Interface Science 336, 268–272 (2009).

  13. 13.

    , , , & Near-infrared reflection from periodically aluminium-doped zinc oxide thin films. Thin Solid Films 519, 2280–2286 (2011).

  14. 14.

    , , , & A simple two-step method to fabricate highly transparent ITO/polymer nanocomposite films. Applied Surface Science 258, 8564–8569 (2012).

  15. 15.

    , , & Localized surface plasmon resonances arising from free carriers in doped quantum dots. Nat Mater 10, 361–6 (2011).

  16. 16.

    et al. Novel synthesis of homogenous CsxWO3 nanorods with excellent NIR shielding properties by a water controlled-release solvothermal process. Journal of Materials Chemistry 20, 8227 (2010).

  17. 17.

    et al. Photothermal ablation cancer therapy using homogeneous CsxWO3 nanorods with broad near-infra-red absorption. Nanoscale 5, 6469–78 (2013).

  18. 18.

    et al. Hydrothermal Synthesis of CsxWO3 and the Effects of N2 Annealing on its Microstructure and Heat Shielding Properties. Journal of Materials Science & Technology 30, 342–346 (2014).

  19. 19.

    , , & Synthesis of one-dimensional potassium tungsten bronze with excellent near-infrared absorption property. ACS Appl Mater Interfaces 3, 2794–9 (2011).

  20. 20.

    et al. Cu2ZnSnS4-Pt and Cu2ZnSnS4-Au Heterostructured Nanoparticles for Photocatalytic Water Splitting and Pollutant Degradation. Journal of the American Chemical Society 136, 9236–9239 (2014).

  21. 21.

    , , & Fine Tuning of the Face Orientation of ZnO Crystals to Optimize Their Photocatalytic Activity. Advanced Materials 18, 3309–3312 (2006).

  22. 22.

    , , & Comparison of Dye-Sensitized ZnO and TiO2 Solar Cells:  Studies of Charge Transport and Carrier Lifetime. The Journal of Physical Chemistry C 111, 1035–1041 (2007).

  23. 23.

    , & Ultraviolet ray absorbing coatings on glass for automobiles. Thin Solid Films 351, 61–65 (1999).

  24. 24.

    et al. Environmentally effective photocatalyst CoO–TiO2 synthesized by thermal precipitation of Co in amorphous TiO2. Applied Catalysis B: Environmental 182, 449–455 (2016).

  25. 25.

    et al. Efficient Co-B-codoped TiO2 photocatalyst for degradation of organic water pollutant under visible light. Applied Catalysis B: Environmental 183, 242–253 (2016).

  26. 26.

    , , & Improving the photocatalytic activity and anti-photocorrosion of semiconductor ZnO by coupling with versatile carbon. Phys Chem Chem Phys 16, 16891–903 (2014).

  27. 27.

    et al. Selective Surface Modification of SiO2−TiO2 Supports with Phosphonic Acids. Chemistry of Materials 16, 5670–5675 (2004).

  28. 28.

    , , , & Change of Adsorption Modes of Dyes on Fluorinated TiO2 and Its Effect on Photocatalytic Degradation of Dyes under Visible Irradiation. Langmuir 24, 7338–7345 (2008).

  29. 29.

    & Enhanced Remote Photocatalytic Oxidation on Surface-Fluorinated TiO2. Langmuir 20, 11523–11527 (2004).

  30. 30.

    , , & Enhancement of Photocatalytic Activity of Mesporous TiO2 Powders by Hydrothermal Surface Fluorination Treatment. The Journal of Physical Chemistry C 113, 6743–6750 (2009).

  31. 31.

    , , , & A CsxWO3/ZnO nanocomposite as a smart coating for photocatalytic environmental cleanup and heat insulation. Nanoscale 7, 17048–17054 (2015).

  32. 32.

    , , & Enhancement of photocurrent and photocatalytic activity of ZnO hybridized with graphite-like C3N4. Energy & Environmental Science 4, 2922–2929 (2011).

  33. 33.

    et al. Resistive memory for harsh electronics: immunity to surface effect and high corrosion resistance via surface modification. Sci Rep 4, 4402 (2014).

  34. 34.

    et al. Graphene/MxWO3 (M = Na, K) nanohybrids with excellent electrical properties. Carbon 94, 309–316 (2015).

  35. 35.

    , , , & Discovery of an excellent IR absorbent with a broad working waveband: Cs(x)WO3 nanorods. Chem Commun (Camb) 47, 8853–5 (2011).

  36. 36.

    et al. Metolachlor photocatalytic degradation using TiO2 photocatalysts. Applied Catalysis B: Environmental 49, 195–205 (2004).

  37. 37.

    et al. A Facile One-Step Solvothermal Synthesis and Electrical Properties of Reduced Graphene Oxide/Rod-Shaped Potassium Tungsten Bronze Nanocomposite. Journal of Nanoscience and Nanotechnology 15, 7305–7310 (2015).

  38. 38.

    , , , & Synergistic Effect of Dual Electron-Cocatalysts for Enhanced Photocatalytic Activity: rGO as Electron-Transfer Mediator and Fe(III) as Oxygen-Reduction Active Site. Sci Rep 5, 13083 (2015).

  39. 39.

    , & Photocatalytic Properties and Photoinduced Hydrophilicity of Surface-Fluorinated TiO2. Chemistry of Materials 19, 116–122 (2007).

  40. 40.

    , , & Quantitative Evaluation of the Photoinduced Hydrophilic Conversion Properties of TiO2 Thin Film Surfaces by the Reciprocal of Contact Angle. The Journal of Physical Chemistry B 107, 1028–1035 (2003).

  41. 41.

    , , & Enhancement of the Photoinduced Hydrophilic Conversion Rate of TiO2 Film Electrode Surfaces by Anodic Polarization. The Journal of Physical Chemistry B 105, 3023–3026 (2001).

Download references

Acknowledgements

This research was supported by the International Sci. & Tech. Cooperation Foundation of Gansu Provincial, China (Grant Nos 1504WKCA088 and 1304WCGA177), the National Science Foundation for Fostering Talents in Basic Research of National Natural Science Foundation of China (Nos 041105 and 041106), the National Natural Science Funds of China (Grant No. 51372105) and the Network Joint Research Center for Materials and Devices, the Grant-in-Aid for Science Research (No. 23241025).

Author information

Affiliations

  1. Department of Materials Science, School of Physical Science and Technology, Lanzhou University, Lanzhou, 730000, China

    • Tongyao Liu
    • , Bin Liu
    • , Jing Wang
    • , Linfen Yang
    • , Xinlong Ma
    • , Hao Li
    • , Yihong Zhang
    •  & Yuhua Wang
  2. Institute of Multidisciplinary Research for Advanced Materials, Tohoku University, 2-1-1 Katahira, Aoba-ku, Sendai, Japan

    • Shu Yin
    •  & Tsugio Sato
  3. The Institute of Scientific and Industrial Research, Osaka University, Japan

    • Tohru Sekino

Authors

  1. Search for Tongyao Liu in:

  2. Search for Bin Liu in:

  3. Search for Jing Wang in:

  4. Search for Linfen Yang in:

  5. Search for Xinlong Ma in:

  6. Search for Hao Li in:

  7. Search for Yihong Zhang in:

  8. Search for Shu Yin in:

  9. Search for Tsugio Sato in:

  10. Search for Tohru Sekino in:

  11. Search for Yuhua Wang in:

Contributions

T.L. and B.L. conducted the most of investigation for the samples. T.L. wrote the main paper. B.L. designed the concept and the experiment method of the research. B.L. and Y.W. supervised the project, had given valuable advices on the proceeding of this work and revised the manuscript. S.Y., T.S. and T.S. had provided precious suggestions on the selection of tungsten bronze as NIR shielding materials. J.W., Y.Z. and L.Y. supported the characterization of the samples. H.L. and X.M. revised the manuscript. All authors discussed the results and commented on the manuscript at all stages.

Competing interests

The authors declare no competing financial interests.

Corresponding authors

Correspondence to Bin Liu or Yuhua Wang.

Supplementary information

Comments

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

Creative CommonsThis work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/