Abstract
We report an all-electric integrable electron focusing lens in n-type GaAs. It is shown that a pronounced focusing peak takes place when the focal point aligns with an on-chip detector. The intensity and full width half maximum (FWHM) of the focusing peak are associated with the collimation of injected electrons. To demonstrate the reported focusing lens can be a useful tool, we investigate the characteristic of an asymmetrically gate biased quantum point contact with the assistance of a focusing lens. A correlation between the occurrence of conductance anomaly in low conductance regime and increase in FWHM of focusing peak is observed. The correlation is likely due to the electron-electron interaction. The reported electron focusing lens is essential for a more advanced electron optics device.
Similar content being viewed by others
Introduction
During the past several years, electronic and optical technologies have seen many encouraging developments. On the electronic end, emergent devices such as spintronics1,2,3 and valleytronics4,5 have been proposed and realized; similarly, devices such as coherent optical memory6 and optical qubit7 have laid the foundation of optical quantum computation. Integrating optical and electronic properties into a single platform or electron optics will provide a unique system for investigating many phenomena emerging from their fusion. The wave nature of electrons in low dimensions, especially ballistic electrons in clean semiconductors, could be exploited for geometrical optical phenomena. In order to realize the potential of electron optics, it is necessary to establish a mapping between the fundamental optical components and their electronic counterparts. In this regard, it is well known that quantum point contacts (QPCs) or other low-dimensional electron sources are equivalent to a coherent optical source8; electronic spin polariser is inspired by an optical polariser9; electronic cavity/mirror shares functional similarities with the optical ones10. Electron focusing with the electrostatic lens has been demonstrated with a double-concave lens11,12. However, the primary parameter that determines the focusing profile has not been addressed.
In the present work, we demonstrate an all-electric electron focusing lens with a more intuitive design and identify the main factor that shapes the focusing profile. A focusing peak occurs whenever the focal point, which is gate-voltage tunable, spatially aligns with the on-chip detector. It is found that the focusing profile is closely associated with the collimation of injected electrons. To give an example of the potential usage of the electronic focusing lens, we utilized this technique to investigate the characteristic of an asymmetrically gate biased QPC. A correlation between the occurrence of conductance anomaly in low conductance regime and increase in FWHM of focusing peak is observed. The correlation is likely due to electron-electron interaction.
Results
To realize an electronic analogue of an optical focusing scheme, it requires both collimated electron source and electron focusing lens Fig. 1(a). The highly collimated ballistic electrons13,14 are injected by two QPCs, i.e., QPC1 and 2 as shown in Fig. 1(b), whereas QPC3 functions as a detector. Electron injection angle concentrates at 0° when the QPC is confined to low conductance regime, but always has a finite angular spread13,14. Before being collected at QPC3, collimated electrons pass through an electronic focusing lens defined via a top gate encapsulating a double-concave shaped hollow regime [Fig. 1(b); see Supplementary Information Note 1 and 2 for comments on lens design. The supplementary information includes results under different experimental conditions and details on simulation, also refs. 15,16,17,18. Electron refraction follows the Snell’s law11,12. The relative refractive index \({N}_{r}=\sqrt{\frac{{n}_{1}}{{n}_{2}}}\), which determines the location of focal point, is adjustable via reducing n2 by applying negative gate voltage (n2 is the electron density under the top-gated regime; n1 is the density within the hollow area or raw 2D density).
The functionality of the electronic lens centered between the QPCs can be verified by noticing an enhancement in the detected signal when the focal point aligns with the saddle point of the detector (QPC3). To detect the real focusing signal, the residual signals were simultaneously drained to Ohmic contacts 4 and 5 in Fig. 1(b); otherwise, all the injected electrons would be drained via the detector whether or not the focusing condition was matched. Figure 1(c) shows a representative result with QPC 1–3 set to G0 (G0 = \(\frac{2{e}^{2}}{h}\)). The residual current I4 + I5 measured at Ohmic contacts 4 and 5 resembled a typical pinched-off behaviour; on the other hand, I3 measured at Ohmic contact 3 yielded a series of peaks. Peaks in I3 near pinched-off regime may arise from charging effect or scattering at low electron density limit as suggested by their insensitivity against transverse magnetic field [Fig. S5 of Supplementary Information]; the small fluctuation can be a result of universal conductance fluctuation; peak occurred at lens gate voltage Vlens ≈ −0.90 V [marked by the bold black arrow in Fig. 1(c)] was an indication of electron focusing. The focal length lf at given Vlens can be calculated from lensmaker’s equation:
where R1 = 1.9 μm and R2 = −1.9 μm are the radius of right and left surface of the lens, D = 2 μm is the thickness of lens, Nr can be extracted from capacitance model19,20 as \({N}_{r}=\sqrt{\frac{{V}_{pin}}{{V}_{pin}-{V}_{lens}}}\), where Vpin indicates the pinched-off voltage of the lens gate. Inserting Vpin = −1.60 V and Vlens = −0.90 V, Eq. (1) yielded that Nr = 1.511 and lf = 2.17 μm which agrees very well with the lithographically defined distance (2.25 μm) between geometric centre of the lens and QPC3. The difference in the value may arise from the fact that the effective dimension of the (electrostatic) lens differs from the lithographically defined one; besides, an offset of the lens along primary axis is also possible. An enhancement in I3 happened when the focal point of the electronic lens aligned with the saddle point of QPC3. In addition, the width of the focusing peak also revealed important insights. The focusing peak started forming once the focal point was driven to the vicinity of the entrance of QPC3 and attenuating when the focal point passed the exit; therefore a change in lf within this range of Vlens should match channel length of QPC3. The full-width half maxima (FWHM) of the focusing peak suggested a change in lf of 313 nm which is consistent with the lithographically defined channel length of 300 nm. The difference in values could probably arise from the finite angular spread of injected electrons.
To further validate the existence of the focusing process, we presented data after the sample was illuminated by a red LED in Fig. 1(d) with all QPCs set to G0. According to Eq. ((1)), Nr must remain the same when focusing peak occurred before and after illumination. It was found that the only prominent peak after illumination, the focusing peak, in I3 happened at Vlen = −1.08 V whereas Vpin became −1.90 V as a result of increased 2D electron density, these values suggest Nr = 1.521 just as before illumination.
It might be concerned that the focusing peak may arise from trivial electrostatic effects such as the cross-coupling between the split gates and lens gate, or coherent effects such as universal conductance fluctuation. These interpretations can be excluded by the data obtained with different injector conductance, different combination of grounding scheme (for instance, both Ohmic 4 and 5 are floating or grounded), temperature and transverse magnetic field dependence [see note 4 of Supplementary Information for detailed discussion].
Temperature dependence of the focusing peak
The evolution of focusing peak with lattice temperature elevated from 20 mK to 1.6 K is presented in Fig. 2(a). The focusing peak intensity γ weakened with increasing temperature and followed the trend based on electron collimation as shown in Fig. 2(b). To avoid the constant pre-factor which could not be calculated directly, γ(T) was normalized against γ(1.6 K). γ was closely associated with electron collimation, it was suggested that21
where l is electron propagation length, lm(T) is the mean free path for electron-electron scattering at given temperature T, which is defined as lm(T) = vF × τee(T) where vF is the Fermi velocity and τee(T) is electron-electron scattering time21
where EF is the Fermi energy, kB is the Boltzmann constant, qTF is the Thomas-Fermi screening wave vector, kF is Fermi wave vector. l can be obtained by assuming electrons follow the classical trajectory connecting QPC1 (QPC2) and QPC3 with refraction at the lens taken into account, whereas lm(T) is fully determined by T and electron density in the area between injectors and detector. The non-uniform electron density underneath the lens (including the top-gated regime and hollow area) was a complex situation. To simplify the calculation, we assume a uniform top-gate, without hollow regime, is patterned between the injector and detectors. The upper bound of the calculation [blue solid line in Fig. 2(b)] corresponds to Vlens = −0.90 V applied to the virtual uniform top-gate, whereas lower bound is given by zero-gate voltage [red solid line in Fig. 2(b)]. It turned out that the experimental data lied between the lower and upper bound but much closer to the upper bound.
The agreement between l and classical trajectory length (through a double-convex lens) further supported that peak at Vlen = −0.90 V arose from electron focusing. The temperature dependence data also indicate that the focusing peak is not due to trivial coherent effect [Supplementary Information Note 4].
Focusing peak with asymmetrically gate biased injector
After confirming the lens was capable of focusing electrons, we utilized the technique to investigate the property of an asymmetrically gate biased QPC where lateral spin-orbit coupling (LSOC) was suggested to play a vital role22,23,24,25,26, even in GaAs27.
The behaviour of injector QPCs with asymmetric gate bias was characterized using standard conductance measurement. Taking QPC1 as an example, if gate voltage Vsg was applied to the bottom arm of the split gate [refers to Fig. 1(b)], Vsg + ΔV would be applied to the upper arm. ΔV was kept negative so that the 1D channel shifted towards the primary axis [Fig 1(a)] instead of the tips of the lens, to avoid diffraction at the tips28. A short plateau-like feature, as marked by the red arrow in Fig. 3(a), below 0.7-anomaly started forming with increasing ΔV similar to previous observations22,23,24,25,26,27. We denoted this feature as sub-0.7-anomaly hereafter. However, the sub-0.7-anomaly was unlikely to arise from previously proposed LSOC22,23,24,25,26,27. In GaAs electron gas, the ground-state electrons propagate along the potential minimum of the 1D channel. For the studied device, the lateral electric field at the potential minimum is about 100 V/m with ΔV = −1 V according to simulation in Fig. 4 [Supplementary Information Note 8], which is insufficient to generate noticeable LSOC. Ideally speaking the electric field at the potential minimum should be zero, the finite value obtained here is likely due to the finite grid spacing used in the simulation.
Additional insight into the observed sub-0.7-anomaly can be extracted from the focusing experiment. In this experiment QPC1 (QPC2 was not used) was set to G0 under different ΔV; on the other hand, QPC3 was under symmetric bias and fixed at G0. The results are summarized in Fig. 3(b,c). It was clear that the focusing peak centred at −1.08 V regardless of ΔV. The robustness of focusing peak position indicates that electron injection angle from a QPC tends to concentrate at 0° even with asymmetric confinement. Assuming that the injection angle concentrates at a non-zero angle α, then the injected electrons should be guided to f * instead of the focal point [see upper panel of Fig. 1(a)]; to make f * align with the saddle point of detector, an adjustment on Vlens is necessary, for instance the focusing peak should occur at Vlens = −1.17 V assuming α = 6°. Although the central position of focusing peak showed no explicit dependence on ΔV, FWHM of focusing peak almost increased monotonically against ΔV, as shown in Fig. 3(c). The broadening of FWHM suggests a larger angular spread of injected electrons; in other words, a reduction in collimation [Supplementary Information Note 7]. FWHM started increasing rapidly at ΔV = −0.4 V which was roughly the same ΔV to trigger the sub-0.7-anomaly.
We suggest that the occurrence of sub-0.7-anomaly and increase in FWHM of focusing peak are possibly due to electron-electron interaction. Applying the asymmetric gate-bias ΔV results in a change in the effective length of the 1D channel, whereas the electron-electron interaction (e-e interaction) especially the exchange part is sensitive to the channel length, it has been shown conductance anomaly can occur between 0.8 × \(\frac{2{e}^{2}}{h}\) to 0.4 × \(\frac{2{e}^{2}}{h}\) depends on the channel length29. On the other hand, for a symmetrically gate-biased QPC, the angle α within which the electrons are highly collimated is given by30,31,
where Eb is the potential at the saddle point where minimum 1D channel width Wmin occurs, Wmax is the critical channel width where electron transport still remains non-adiabatic. It is found that α changes from 5.24° (ΔV = 0) to 5.17° (ΔV = −1 V) without e-e interaction; on the other hand, α increases from 5.77° (ΔV = 0) to 6.77° (ΔV = −1 V) after taking e-e interaction into account. It seems that e-e interaction is an essential ingredient for an observable change in FWHM [see Note 9 of Supplementary Information for a more detailed discussion].
It is also important to check the role of disorder, which can result in multiple irregular features on conductance characteristic. If we try to understand the conductance measurement in Fig. 3(a) based on disorder, it is natural to think the magenta trace (the third one from the right side), where several irregular features are observed, corresponds to the case where the effect of disorder is most substantial. The smoothing of the two most right traces indicates the channel is moving away from the disorder. It is then expected that the FWHM of focusing peak should follow a non-monotonic trend if disorder plays a primary role, however, the experimental result shows a monotonic trend.
Extending the focusing scheme to material with strong spin-orbit coupling
It is helpful to apply the focusing scheme to material with strong intrinsic spin-orbit coupling (SOC). The strong intrinsic SOC can causes lateral motion, so that the two spin-branches tend to move along the opposite edges of the 1D channel where the lateral electric field is noticeable22. LSOC is induced as a result of the lateral electric field.
It has been shown that a small out-plane magnetic field can make angular distribution centered at a finite angle rather than 0°32. The effective out-plane magnetic field induced by intrinsic SOC can have similar influence. Therefore, it is expected that the angular spread has two peaks at ± θ in the presence of intrinsic SOC (±sign depends on spin orientation) instead of a single peak at 0° when intrinsic SOC is absent. The spin branches will thus lead to two focusing peaks. Information on both the intrinsic SOC and LSOC can be extracted from the focusing profile.
Conclusion
We have developed a double-convex electron focusing lens which is an essential component for a complete tool kit of electron optics. A focusing peak occurred when the focal point of the lens aligned with the detector, the intensity of focusing was closely associated with the degree of electron collimation. Using the focusing lens, we found that the injection angle of 1D electrons tends to concentrate at 0° even with considerable asymmetric gate bias ΔV. However, the angular spread broadened with increasing ΔV. The increment of FWHM was correlated with the occurrence of a sub-0.7-anomaly, possibly due to electron-electron interaction. The focusing scheme is ready to be extended to material with strong intrinsic spin-orbit interaction, where it allows to selectively polarized electron spin in the injector/detector and study the interplay between local spin states by monitoring the evolution in corresponding focusing peak.
References
Crooker, S. et al. Imaging spin transport in lateral ferromagnet/semiconductor structures. Science 309, 2191–2195 (2005).
Wunderlich, J. et al. Spin Hall effect transistor. Science 330, 1801–1804 (2010).
Betthausen, C. et al. Spin-transistor action via tunable Landau-Zener transitions. Science 337, 324–327 (2012).
Rycerz, A., Tworzydło, J. & Beenakker, C. Valley filter and valley valve in graphene. Nature Physics 3, 172 (2007).
Schaibley, J. R. et al. Valleytronics in 2D materials. Nature Reviews Materials 1, 16055 (2016).
Hill, M. T. et al. A fast low-power optical memory based on coupled micro-ring lasers. nature 432, 206 (2004).
Babichev, S. A., Appel, J. & Lvovsky, A. I. Homodyne tomography characterization and nonlocality of a dual-mode optical qubit. Phys. Rev. Lett. 92, 193601 (2004).
Topinka, M. et al. Imaging coherent electron flow from a quantum point contact. Science 289, 2323–2326 (2000).
Datta, S. & Das, B. Electronic analog of the electro-optic modulator. Applied Physics Letters 56, 665–667 (1990).
Duncan, D. S., Topinka, M. A., Westervelt, R. M., Maranowski, K. D. & Gossard, A. C. Aharonov-Bohm phase shift in an open electron resonator. Phys. Rev. B 64, 033310 (2001).
Sivan, U., Heiblum, M., Umbach, C. P. & Shtrikman, H. Electrostatic electron lens in the ballistic regime. Phys. Rev. B. 41, 7937–7940 (1990).
Spector, J., Stormer, H., Baldwin, K., Pfeiffer, L. & West, K. Electron focusing in two-dimensional systems by means of an electrostatic lens. Applied physics letters 56, 1290–1292 (1990).
Molenkamp, L. W. et al. Electron-beam collimation with a quantum point contact. Phys. Rev. B. 41, 1274–1277 (1990).
Saito, M., Takatsu, M., Okada, M. & Yokoyama, N. Analysis of the angular distribution of electrons injected through a quantum point contact by use of a Green’s function with a weak-magnetic-field approximation. Phys. Rev. B. 46, 13220–13233 (1992).
Ofek, N. et al. Role of interactions in an electronic fabry–perot interferometer operating in the quantum hall effect regime. Proceedings of the National Academy of Sciences (2010).
Davies, J. H., Larkin, I. A. & Sukhorukov, E. V. Modelling the patterned two-dimensional electron gas: Electrostatics. Journal of Applied Physics 77, 4504–4512 (1995).
Martin-Moreno, L., Nicholls, J. T., Patel, N. K. & Pepper, M. Non-linear conductance of a saddle-point constriction. Journal of Physics: Condensed Matter 4, 1323 (1992).
Wang, C. K. & Berggren, K. F. Spin splitting of subbands in quasi-one-dimensional electron quantum channels. Phys. Rev. B54, R14257–R14260 (1996).
Yacoby, A., Sivan, U., Umbach, C. P. & Hong, J. M. Interference and dephasing by electron-electron interaction on length scales shorter than the elastic mean free path. Phys. Rev. Lett. 66, 1938–1941 (1991).
Yan, C. et al. Coherent spin amplification using a beam splitter. Phys. Rev. Lett. 120, 137701 (2018).
Molenkamp, L. W., Brugmans, M. J. P., van Houten, H. & Foxon, C. T. Electron-electron scattering probed by a collimated electron beam. Semiconductor Science and Technology 7, B228 (1992).
Debray, P. et al. All-electric quantum point contact spin-polarizer. Nature Nanotechnology 4, 759 (2009).
Burke, A. et al. Extreme sensitivity of the spin-splitting and 0.7 anomaly to confining potential in one-dimensional nanoelectronic devices. Nano letters 12, 4495–4502 (2012).
Chuang, P. et al. All-electric all-semiconductor spin field-effect transistors. Nature nanotechnology 10, 35 (2015).
von Pock, J. et al. Quantization and anomalous structures in the conductance of Si/SiGe quantum point contacts. Journal of Applied Physics 119, 134306 (2016).
Das, P. P. et al. Dependence of the 0.5 × 2e 2∕h conductance plateau on the aspect ratio of InAs quantum point contacts with in-plane side gates. Journal of Applied Physics 121, 083901 (2017).
Pokhabov, D. et al. Lateral-electric-field-induced spin polarization in a suspended GaAs quantum point contact. Applied Physics Letters 112, 082102 (2018).
Hersch, J. S., Haggerty, M. R. & Heller, E. J. Influence of diffraction on the spectrum and wave functions of an open system. Phys. Rev. E. 62, 4873–4888 (2000).
Jaksch, P., Yakimenko, I. & Berggren, K.-F. From quantum point contacts to quantum wires: Density-functional calculations with exchange and correlation effects. Phys. Rev. B. 74, 235320 (2006).
Beenakker, C. W. J. & Houten, Hv Magnetotransport and nonadditivity of point-contact resistances in series. Phys. Rev. B. 39, 10445–10448 (1989).
Crook, R., Smith, C. G., Barnes, C. H. W., Simmons, M. Y. & Ritchie, D. A. Imaging diffraction-limited electronic collimation from a non-equilibrium one-dimensional ballistic constriction. Journal of Physics: Condensed Matter 12, L167–L172 (2000).
Usuki, T., Takatsu, M., Kiehl, R. A. & Yokoyama, N. Numerical analysis of electron-wave detection by a wedge-shaped point contact. Phys. Rev. B. 50, 7615–7625 (1994).
Acknowledgements
The authors gratefully acknowledge assistance on low-temperature measurement setup from Dr. Sanjeev Kumar. The work was funded by United Kingdom Research and Innovation (UKRI).
Author information
Authors and Affiliations
Contributions
C.Y. designed and performed the experiments; C.Y. and M.P. analyzed the data; P.S. fabricated the devices; J.G. did e-beam lithography; I.F. and D.R. grew the wafer; C.Y. wrote the paper with inputs from M.P., and other co-authors. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Yan, C., Pepper, M., See, P. et al. Demonstration of electron focusing using electronic lenses in low-dimensional system. Sci Rep 10, 2593 (2020). https://doi.org/10.1038/s41598-020-59453-x
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-020-59453-x
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.