Article | Open

Three-Dimensional Bi-Continuous Nanoporous Gold/Nickel Foam Supported MnO2 for High Performance Supercapacitors

  • Scientific Reportsvolume 7, Article number: 17857 (2017)
  • doi:10.1038/s41598-017-17872-3
  • Download Citation
Published online:


A three-dimensional bi-continuous nanoporous gold (NPG)/nickel foam is developed though the electrodeposition of a gold–tin alloy on Ni foam and subsequent chemical dealloying of tin. The newly-designed 3D metal structure is used to anchor MnO2 nanosheets for high-performance supercapacitors. The formed ternary composite electrodes exhibit significantly-enhanced capacitance performance, rate capability, and excellent cycling stability. A specific capacitance of 442 Fg−1 is achieved at a scan rate of 5 mV s−1 and a relatively high mass loading of 865 μg cm−2. After 2500 cycles, only a 1% decay is found at a scan rate of 50 mV s−1. A high power density of 3513 W kg−1 and an energy density of 25.73 Wh kg−1 are realized for potential energy storage devices. The results demonstrate that the NPG/nickel foam hybrid structure significantly improves the dispersibility of MnO2 and makes it promising for practical energy storage applications.


The rapid development of the electronics industry has increased demands in corresponding electrical energy storage devices. Among various energy storage devices, pseudocapacitors have attracted significant interest during the past decade due to their high specific capacitance, excellent charge/recharge characteristics, and long cycling life1. The most widely used active electrode materials for pseudocapacitors include transition metal oxides and hydroxides such as RuO22,3, CoO4, NiO5, and MnO26, which possess a range of reversible oxidation states for highly efficient redox charge transfer. Among them, MnO2 has been regarded as one of the most promising pseudocapacitive materials for high performance supercapacitors (SCs) owing to its high theoretical specific capacitance (1370 F g−1), low cost, environmentally friendly nature, and natural abundance7,8. However, MnO2 electrodes often suffer from intrinsically poor conductivity (10−5~10−6 S cm−1)9,10. The respectable theoretical capacitance can only be realized in the form of thin films (ten of nanometers) or nanoparticles with a low loading amount (<10 μg cm−2)11.

To overcome the aforementioned drawback, a variety of strategies have been employed to improve the conductivity of MnO2. Jayan Thomas et al. utilized spin-on nanoprinting to print large area, well-ordered PAN nanopillar arrays for the loading of MnO212. Various carbon based composite materials, such as carbon nanoparticles (CNPs)13, carbon nanotubes (CNTs)14,15,16,17,18, carbon nanowires (CNWs)19,20,21, and graphene22,23,24,25 have also been introduced to create hybrid materials with MnO2 oxides to improve the conductivity. Despite some of the improvements, researchers still suffer from complex fabricating procedures and modest capacitive behavior.

Recently, nanoporous gold (NPG) has attracted much attention for its excellent conductivity, large surface area, chemical stability, and biocompatibility. It has been regarded as a potential candidate for various areas such as supercapacitors26,27, sensors28, catalysis29, fuel cells30, and enhanced fluorescence31. Professor Chen et al. have proposed thick MnO2 layer on free-standing NPG films to close the theoretical gravimetric specific capacitance of MnO227. They also fabricated these electrodes into nonaqueous symmetric supercapacitors for demonstrating the advantages of this structure32. However, traditional NPG films are typically obtained by etching Au-Ag alloy thin film derived from the melting method, which is unsafe and consume much energy. In addition, the highest gravimetric specific capacitance can only be gained when the MnO2 layer is rather thin (very low mass-loading), which is far away from commercial application33.

To resolve this problem, we developed a mild two-step strategy to fabricate high quality NPG films directly supported on Ni foam for the loading of MnO2 which acts as a high-performance supercapacitor. A room temperature electrodeposition method of the Au-Sn alloy was used to integrate the Au-Sn thin film directly onto the Ni foam, followed by selective chemical dealloying of Sn and electrodeposition of MnO2. The fabricating strategy is safe, facile, reproducible, and relatively inexpensive compared to other methods for preparing noble metal substrates. The hierarchical NPG/Ni foam structure is of great importance in our design of a supercapacitor as it not only ensures efficient charge/electrolytes transfer, but also provides a substrate with large surface area to disperse loaded MnO2 and prevent it from agglomerating. Significant improvement was observed by comparing capacitive properties of samples with and without the NPG structure. By introducing NPG structure, the electrode exhibits a capacitance of nearly 3 times higher than the one without. The proposed 3D bi-continuous metal structure may have the potential to be applied to many promising energy storage devices in which the performance is mainly limited by the low conductivity of materials.


Figure 1 shows low and high-magnification SEM images of the MnO2/NPG/Ni foam (denoted as MnO2/NPG) and the MnO2/Ni foam. The Ni foam has the typical morphology of a porous framework, with a pore size of 200–300 μm (Fig. 1a–c). From Fig. 1d–f, it can be seen that a continuous thin film of NPG is uniformly coated on the Ni foam and the nanopores are of 50–150 nm. Few cracks were observed during the dealloying procedure because the initial Sn/Au ratio (about 1:1 in atomic ratio) is not enough to cause a significant shrinkage of volume. After depositing MnO2 on NPG, we can see that some nanosheets were loaded on NPG skeleton (Fig. 1g–i). For the sample with the MnO2 plating amount up to 865 μg cm−2 (examined by ICP), no obvious agglomeration of MnO2 nanosheets was observed on the surface of the NPG film. As a control group, MnO2 directly deposited on Ni foam presents numerous, densely-packed MnO2 nanosheets (Fig. j-l). In contrast, the MnO2/NPG (Fig. 1c and inset) illustrates a bi-continuous nanoporous structure that consists of quasi-periodic nanopores and gold ligaments, on which the MnO2 layer appears much more dispersive. The detailed structure of MnO2/NPG can also be observed in TEM image (inset in Fig. 1i).

Figure 1
Figure 1

SEM images of bare Ni foam (ac) NPG (df) MnO2/NPG (gi) and MnO2/Ni foam (jl) with different magnification. The inset in (i) shows the TEM image of the MnO2/NPG nano structure.

The evidence of successful hybridization can also be verified through the energy-dispersive spectrum (EDS), shown in Fig. 2a. Only three metallic elements in the MnO2/NPG electrode were detected. The corresponding elemental mapping images demonstrated the uniform distribution of O, Mn, Ni, and Au (Fig. 2b), which match the SEM images very well.

Figure 2
Figure 2

Energy-dispersive spectrum of the MnO2/NPG (a), corresponding elemental mapping images of O, Mn, Ni, and Au (b), comparison of the BET specific surface areas of the Ni foam, NPG/Ni foam, and MnO2/NPG (c), and XPS spectra of Mn 2p for the MnO2/NPG and the MnO2/Ni foam electrodes (d).

The BET measurement (Fig. 2c) reveals that the specific surface area of Ni foam approaches zero relative to nanoporous gold’s level (24.8 m2 g−1), and the specific surface area of MnO2/NPG was reduced to approximately 80% (19.84 m2 g−1) as a result of the MnO2 electrodeposition, which is in good agreement with SEM and TEM results.

The XPS spectra of the MnO2/NPG and MnO2/Ni foam electrodes are shown in Fig. 2d. It mainly consists of two distinct peaks centred at 642.8 eV and 654.6 eV, which are respectively ascribed to Mn 2p3/2 and Mn 2p1/234. In this work, the signals of Mn 2p are most likely caused by the Mn4+ chemical state as MnO2. In addition, the Mn4+ peaks of the MnO2/NPG distinctly shift to higher energies than those of the MnO2/Ni foam, indicating the strong chemical interaction between Au and MnO26,35. For a deposition time of 20 min, the amounts of loaded MnO2 are almost the same for the two electrodes, but the peaks’ intensity of Mn4+ in the MnO2/NPG is much higher, revealing that the presence of nanoporous gold significantly improved the dispersibility of MnO2 on the substrate36. These results also suggest that the introduction of nanoporous gold onto nickel foam may contribute to enhanced ion and electron diffusion, resulting in a high-rate performance.

The electrochemical measurements of the MnO2/NPG and MnO2/Ni foam electrodes were tested in 1 mol/L Na2SO4. Typical CV curves of the MnO2/NPG electrode at scan rates ranging from 5 to 100 mV s−1 show much better rectangularity than that of the MnO2/Ni foam electrode (Fig. 3a,d). It is obviously seen that the current intensity increases with the scan rates, while the positions of the redox peaks shift slightly6, showing its good electrochemical reversibility. Generally, the energy storage process of MnO2 is a reversible successive surface redox reaction, resulting the shape of CV curves similar to the electric double layer capacitor (EDLC)37, which also can be showed in Fig. 3d. However, the radius of electrolyte ions and the microstructure of the MnO2 can possibly lead to faradic phenomena occur during the charge-storage mechanism, which is not so successive. As described in several previous researches, the microstructure of the MnO2@NPG/Ni foam has a big difference with MnO2/Ni foam, which can make the intercalation/deintercalation of ions in the MnO2 solid phase possible and result in the redox peaks in CV curves32,38,39,40.

Figure 3
Figure 3

CV curves of the MnO2/NPG (a) and the MnO2/Ni foam (d) at different scan rates (5–100 mV s−1), GCD curves of the MnO2/NPG (b) and the MnO2/Ni foam (e) at different current densities (1–10 A g−1), and corresponding specific capacitance comparisons as a function of the scan rate (c) and the current density (f). All the tests above were performed in 1 mol/L Na2SO4 aqueous solution.

The higher current densities obtained by the MnO2/NPG show improved electron transportation and lower internal resistance. The superior performances of the MnO2 loaded on the NPG/Ni foam can be attributed to two main reasons: (1) the large contact area between the current collector and active material can significantly shorten the electron transfer distance and increase the number of electrochemically active sites for the redox reaction and (2) dispersing capacitive materials onto a large surface area greatly improved the conductivity of pseudocapacitive materials12.

Galvanostatic charge-discharge (GCD) curves were performed in Fig. 3b,e. The GCD curves of the MnO2/NPG, with current density ranging from 1 A g−1 to 10 A g−1, are more symmetrical than those of the MnO2/Ni foam, which validate its improved capacitive behavior. In addition, at the start of the discharge curves, the voltage drop is quite small, indicating very low internal resistance between the electrodes.

For specific capacitances at various scan rates, the MnO2/NPG electrode showed an increase of approximately 3 times when compared to the MnO2/Ni foam electrode, as is shown in Fig. 3c. The C v decreases with an increase of the scan rates, and the highest specific capacitance of the MnO2/NPG electrode reached upwards of 442 F g−1 at the scan rate of 5 mV s−1. The consistency of these curves reveals the excellent capacitive behavior of the MnO2/NPG electrode. Besides, this capacitance of this MnO2/NPG electrode was compared with some previous researches based on MnO2 material, demonstrating rather good performance, as presented in Table 1.

Table 1 Capacitance comparison between this work and other previous MnO2 based materials.

The enhanced electrochemical performance of the MnO2/NPG hybrid electrode was further confirmed by the electrochemical impedance spectroscopy (EIS) measurements. Figure 4a and b shows the Nyquist plots for the MnO2/NPG and the MnO2/Ni foam after the 2500th and 1000th cycles respectively. The equivalent electrical circuit in Fig. 4c was obtained by fitting the impedance data. The internal resistance (R s ) is the sum of the ionic resistance of the electrolyte, the intrinsic resistance of active materials, and the contact resistance at the active material/current collector interface. The Faradic reactions corresponded to the interfacial charge transfer resistance (R ct ), which are related to the interface between the electrode and electrolyte, and the electrical charge transfer in the Faradic process of the electrode materials. A constant phase element was used to account for the double-layer capacitance and pseudocapacitance. The Warburg impedance corresponds to the straight line in low-frequency area, which is associated with the ion diffusion in the electrode. The charge-transfer resistances obviously decreased with nanoporous gold coating, which reveals that the bi-continuous nanoporous network of the MnO2/NPG electrode significantly improved the conductivities of the electrode materials, ion transfer, and charge transfer.

Figure 4
Figure 4

Nyquist plots of EIS performed in 1 mol/L Na2SO4 for the MnO2/NPG before and after 2500 cycles (a) and the MnO2/Ni foam before and after 1000 cycles (b), the equivalent circuit diagram of the two electrodes for the EIS analysis (c), and cycling performance of the corresponding electrodes during 2500 cycles and 1000 cycles at the scan rate of 50 mV/s (d).

After cycles, the R ct of the MnO2/NPG electrode decreased from 95.56 Ω to 23.59 Ω where the MnO2/Ni foam electrode evidently increased from 543.1 Ω to 3541 Ω. The increased resistance of the MnO2/Ni foam is mainly attributed to the low conductivity of MnO2, compared with the as prepared MnO2. MnO2 sheets after cycles become larger and thicker after 1000 cycles, which causes lower electron/ion transfer and thereby capacitance fading of pure MnO2 due to the reduced effective surface areas and low electronic conductivity. To prove these, SEM images of MnO2/NPG electrode and MnO2/Ni foam electrode after cycling 2500 time and 1000 time were shown in Figure S1. As seen in the SEM images, after 1000 cycles, most of the MnO2 sheets loaded directly on Ni foam agglomerate tightly, which could be the main reason for the increase of Rct (Figure S1a–c). However, the structure of the MnO2@NPG/Ni foam electrode retained well and distribution of MnO2 sheets seems more uniform, which contributes to the decrease of the Rct (Figure S1d–f). Compared to the bare MnO2 micro-supercapacitor, the MnO2/NPG composite micro-supercapacitor has a lower resistance, which is of great importance since less energy and less power will be wasted to produce unwanted heat during the charge–discharge processes.

Furthermore, the cycling performances of the MnO2/NPG electrode and the MnO2/Ni foam electrode after long-term cycling are shown in Fig. 4d. The specific capacitance of the MnO2/Ni foam electrode rapidly dropped to 65.3% after 1000 cycles, as a result of irreversible reactions. Instead, the MnO2/NPG electrode was found to exhibit an excellent cycle life over the entire cycle-number range. The capacitance retention of the MnO2/NPG electrode is quite stable and still remains 99% of its initial value even after 2500 cycles, indicating that the electrode materials had excellent cycle stability and quite a high degree of reversibility in charge-discharge cycling.


In this work, we have prepared the MnO2/NPG hybrid electrode by electrodeposition of a gold-tin alloy on Ni foam, selective chemical etching in alkaline media, and electrodeposition of MnO2. This 3D nanoporous substrate with high porosity greatly enhances the surface area compared to that of the planar electrode and improves the conductivity and dispersibility of the loaded MnO2. Moreover, the MnO2/NPG hybrid electrode shows remarkable enhancements in specific capacitance, charge-discharge ability, as well as cyclic stability. The simplicity of the nano-architectured electrodes and their excellent performances has shown promising features for practical energy storage systems. The as prepared MnO2/NPG hybrid electrodes exhibit a specific capacitance of 442 F g−1 at a scan rate of 5 mV s−1. The specific capacitance only decreased by 1% after 2500 cycles at a scan rate of 50 mV s−1. Meanwhile, a high power density of 3513 W kg−1 and an energy density of 25.73 Wh kg−1 were achieved. By comparing the properties with those of MnO2/Ni foam electrodes, the NPG structure has shown its importance and advantages in our hybrid electrodes.


Chemicals and materials

The Au-Sn plating solution was purchased from Huizhou Leadao Electronic Material Co. Ltd. Hydrochloric acid (HCl), potassium hydroxide (KOH), hydrogen peroxide (H2O2), sodium sulphate (Na2SO4) and dimethyl sulfoxide (DMSO) was purchased from Guangzhou Chemical Reagent Factory. Ammonium acetate (NH4Ac) and manganese acetate (MnAc2) was purchased from Shanghai Aladdin Biochemical Technology Co., Ltd. Nickel foam was purchased from Kunshan Longshengbao Electronic Material Co., Ltd. Platinum foil electrode and saturated calomel electrode (SCE) were purchased from Shanghai INESA Scientific Instrument Co., Ltd.

Fabrication of MnO2/NPG electrodes

The fabrication procedure consists of four main steps. As illustrated in Fig. 5, Ni foam was cut into the proper size (approximately 1 cm × 7 cm × 1 mm), pre-treated with 5 mol/L HCl solution for 30 min to remove the oxide layer on the surface, and then rinsed thoroughly with deionized water. The Au-Sn alloy electrodeposition was carried out in a two-electrode system with the clean Ni foam as the working electrode and a Pt foil as the counter electrode. The Au-Sn alloy film was galvanostatically electrodeposited on Ni foam in an Au-Sn alloy plating solution (Huizhou Leadao Electronic Material Co. Ltd., China) with a current density of 0.5 A dm−2 for 10 min at 45 °C.

Figure 5
Figure 5

Schematic showing the fabricating procedure of the MnO2/NPG electrode.

After electrodeposition, the electrode was rinsed with deionized water and dried in air. It was then immersed into a 5 mol/L NaOH and 1 mol/L H2O2 solution for 3 days to selectively etch Sn away from the Au-Sn alloy film, leading to the formation of an NPG film on Ni foam. After etching, the Ni foam was carefully rinsed with deionized water and dried in air. Finally, MnO2 was electrodeposited on the NPG/Ni foam electrode from an aqueous solution containing 0.01 M manganese acetate (MnAc2) and 0.02 M ammonium acetate (NH4Ac) in a solvent mixture of 90% DI water and 10% dimethyl sulfoxide (DMSO) by a galvanostatic electrodeposition method. The MnO2 electrodeposition experiments were performed in a standard three-electrode electrochemical cell. The NPG/Ni foam electrode was used as the working electrode, a Pt foil as the counter electrode, and a saturated calomel electrode (SCE) as the reference electrode. The MnO2 electrodeposition was conducted by applying a constant current of 0.8 mA cm−2 for 20 min. As a control experiment, a MnO2/Ni foam electrode, without NPG film, was produced by the same procedure.

Characterization methods

The microstructure of the samples was investigated using field-emission scanning electron microscopy (SEM, JEOL, JSM-6700F, 15 keV). X-ray diffraction (XRD) measurements were performed on a Rigaku D/max-2200/PC diffractometer using Cu Kα radiation. The amount of loaded MnO2 was detected by inductively coupled plasma mass spectrometry (ICP-MS, Thermo Scientific iCAP Qc). Electrochemical measurements were carried out on a Gamry Reference 600 electrochemical workstation in a three-electrode setup with 1 mol/L Na2SO4 as the electrolyte. The MnO2/NPG electrode, platinum foil, and a SCE electrode acted as the working electrode, counter electrode, and reference electrode respectively. The electrochemical impedance spectroscopy (EIS) measurements were conducted in a frequency range from 100 kHz to 0.1 Hz with a perturbation amplitude of 5 mV. All electrochemical measurements were performed at room temperature (25 ± 2 °C).

Calculation methods

Voltammetric specific capacitances (C v , F g−1) were calculated from the CV curves at different scan rates by the following equation:

C v = ( I × d V ) / ( m × s × V )

where I is the current (A), V is the potential (V), m is the mass (g) of the loaded MnO2, and s is the scan rate (V s−1).

Charge-discharge specific capacitances (shown in Fig. 3f) were also calculated from the GCD curves with different current densities using the following equation:

C= ( I × Δ t ) / ( m × Δ V )

where I/m is the current density (A g−1) applied in charge/discharge measurements, ∆t is the discharge time (s), and ∆V is the potential change (V).

Additional information

Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.


  1. 1.

    Gu, T. & Wei, B. All-solid-state stretchable pseudocapacitors enabled by carbon nanotube film-capped sandwich-like electrodes. Acs Appl Mater Interfaces 8, 25243–25250 (2016).

  2. 2.

    Hu, C. et al. Design and tailoring of the nanotubular arrayed architecture of hydrous RuO2 for next generation supercapacitors. Nano Letters 6, 2690–2695 (2006).

  3. 3.

    Wang, W. et al. Hydrous ruthenium oxide nanoparticles anchored to graphene and carbon nanotube hybrid foam for supercapacitors. Scientific Reports 4, 4452 (2014).

  4. 4.

    Xu, J. et al. Preparation and electrochemical capacitance of cobalt oxide (CoO) nanotubes as supercapacitor material. Electrochimica Acta 56, 732–736 (2011).

  5. 5.

    Lee, J. W. et al. Nanosheets based mesoporous NiO microspherical structures via facile and template-free method for high performance supercapacitors. Electrochimica Acta 56, 4849–4857 (2011).

  6. 6.

    Iamprasertkun, P. et al. Charge storage mechanisms of manganese oxide nanosheets and N-doped reduced graphene oxide aerogel for high-performance asymmetric supercapacitors. Scientific Reports 6, 37560 (2016).

  7. 7.

    Guan, C. et al. Nanoporous walls on macroporous foam: rational design of electrodes to push areal pseudocapacitance. Advanced Materials 24, 4186–4190 (2012).

  8. 8.

    Mathieu, T. et al. Charge storage mechanism of MnO2 electrode used in aqueous electrochemical capacitor. Chemistry of Materials 16, 3184–3190 (2004).

  9. 9.

    Lu, X. et al. Facile synthesis of large-area manganese oxide nanorod arrays as a high-performance electrochemical supercapacitor. Energy & Environmental Science 4, 2915–2921 (2011).

  10. 10.

    Wei, W. et al. Manganese oxide-based materials as electrochemical supercapacitor electrodes. Chemical Society Reviews 40, 1697–1721 (2011).

  11. 11.

    Broughton, J. N. & Brett, M. J. Investigation of thin sputtered Mn films for electrochemical capacitors. Electrochimica Acta 49, 4439–4446 (2004).

  12. 12.

    Yu, Z. et al. Highly ordered MnO2 nanopillars for enhanced supercapacitor performance. Advanced Materials 25, 3302–3306 (2013).

  13. 13.

    Yuan, L. et al. Flexible solid-state supercapacitors based on carbon nanoparticles/MnO2 nanorods hybrid structure. Acs Nano 6, 656–661 (2012).

  14. 14.

    Cheng, Y. et al. Synergistic effects from graphene and carbon nanotubes enable flexible and robust electrodes for high-performance supercapacitors. Nano Letters 12, 4206–4211 (2012).

  15. 15.

    Huang, M. et al. Self-assembly of mesoporous nanotubes assembled from interwoven ultrathin birnessite-type MnO2 nanosheets for asymmetric supercapacitors. Scientific Reports 4, 3878 (2014).

  16. 16.

    Choi, C. et al. Stretchable, weavable coiled carbon nanotube/MnO2/polymer fiber solid-state supercapacitors. Scientific Reports 5, 9387 (2015).

  17. 17.

    Liang, K. et al. In situ synthesis of SWNTs@MnO2/polypyrrole hybrid film as binder-free supercapacitor electrode. Nano Energy 9, 245–251 (2014).

  18. 18.

    Yu, D. et al. Scalable synthesis of hierarchically structured carbon nanotube-graphene fibres for capacitive energy storage. Nature Nanotechnology 9, 555–562 (2014).

  19. 19.

    Liu, J. et al. Energy storage: Co3O4 nanowire@MnO2 ultrathin nanosheet core/shell arrays: a new class of high‐performance pseudocapacitive materials (Adv. Mater. 18/2011). Advanced Materials 23, 2076–2081 (2011).

  20. 20.

    Tao, J. et al. Solid-state high performance flexible supercapacitors based on polypyrrole-MnO2-carbon fiber hybrid structure. Scientific Reports 3, 2286 (2013).

  21. 21.

    Yu, D. et al. Transforming pristine carbon fiber tows into high performance solid‐state fiber supercapacitors. Advanced Materials 27, 4895–4901 (2015).

  22. 22.

    Sun, L. et al. From coconut shell to porous graphene-like nanosheets for high-power supercapacitors. Journal of Materials Chemistry A 1, 6462–6470 (2013).

  23. 23.

    Zhou, Z. & Wu, X. F. Graphene-beaded carbon nanofibers for use in supercapacitor electrodes: Synthesis and electrochemical characterization. Journal of Power Sources 222, 410–416 (2013).

  24. 24.

    Raccichini, R., Varzi, A., Passerini, S. & Scrosati, B. The role of graphene for electrochemical energy storage. Nature materials 14, 271–279 (2015).

  25. 25.

    Hu, S. et al. A hierarchical structure of carbon-coated Li3VO4 nanoparticles embedded in expanded graphite for high performance lithium ion battery. Journal of Power Sources 303, 333–339 (2016).

  26. 26.

    Meng, F. & Ding, Y. Sub-micrometer-thick all-solid-state supercapacitors with high power and energy densities. Adv Mater 23, 4098–4102 (2011).

  27. 27.

    Lang, X., Hirata, A., Fujita, T. & Chen, M. Nanoporous metal/oxide hybrid electrodes for electrochemical supercapacitors. Nat Nanotechnol 6, 232–236 (2011).

  28. 28.

    Zhang, L. et al. Nanoporous gold based optical sensor for sub-ppt detection of mercury ions. Acs Nano 7, 4595–4600 (2013).

  29. 29.

    Li, Z. et al. Three-dimensional nanoporous gold–cobalt oxide electrode for high-performance electroreduction of hydrogen peroxide in alkaline medium. Journal of Power Sources 294, 136–140 (2015).

  30. 30.

    Zeis, R., Mathur, A., Fritz, G., Lee, J. & Erlebacher, J. Platinum-plated nanoporous gold: An efficient, low Pt loading electrocatalyst for PEM fuel cells. Journal of Power Sources 165, 65–72 (2007).

  31. 31.

    Yuan, H. et al. Single nanoporous gold nanowire as a tunable one-dimensional platform for plasmon-enhanced fluorescence. Chemical Communications 52, 1808–1811 (2015).

  32. 32.

    Chen, L. Y. et al. High-energy-density nonaqueous MnO2@nanoporous gold based supercapacitors. Journal of Materials Chemistry A 1, 92020–9207 (2013).

  33. 33.

    Gogotsi, Y. & Simon, P. Materials science. True performance metrics in electrochemical energy storage. Science 334, 917–918 (2011).

  34. 34.

    Sumboja, A. et al. Large areal mass, flexible and free-standing reduced graphene oxide/manganese dioxide paper for asymmetric supercapacitor device. Advanced Materials 25, 2809–2815 (2013).

  35. 35.

    Epling, W. S. et al. Surface characterization study of Au/α-Fe2O3 and Au/Co3O4 low-temperature CO oxidation catalysts. Journal of Physical Chemistry 100, 9929–9934 (1996).

  36. 36.

    Kondrat, S. et al. Effect of pore size and its dispersity on the energy storage in nanoporous supercapacitors. Energy & Environmental Science 5, 6474–6479 (2012).

  37. 37.

    Simon, P. & Gogotsi, Y. Materials for electrochemical capacitors. Nat Mater 7, 845–854 (2008).

  38. 38.

    Ghodbane, O. et al. Microstructural effects on charge-storage properties in MnO2-based electrochemical supercapacitors. ACS Appl Mater Interfaces 1, 1130–1139 (2009).

  39. 39.

    Brousse, T. et al. Crystalline MnO2 as possible alternatives to amorphous compounds in electrochemical supercapacitors. Journal of The Electrochemical Society 153, A2171–A2180 (2006).

  40. 40.

    Qu, Q. et al. Electrochemical performance of MnO2 nanorods in neutral aqueous electrolytes as a cathode for asymmetric supercapacitors. The Journal of Physical Chemistry C 113, 14020–14027 (2009).

  41. 41.

    Tsai, Y.-C. et al. An effective electrodeposition mode for porous MnO2/Ni foam composite for asymmetric supercapacitors. Materials 9, 246 (2016).

  42. 42.

    Li, R. et al. Development of electrochemical supercapacitors with uniform nanoporous silver network. Electrochimica Acta 182, 224–229 (2015).

  43. 43.

    Qiu, T. et al. Au@MnO2 core-shell nanomesh electrodes for transparent flexible supercapacitors. Small 10, 4136–4141 (2014).

  44. 44.

    Hu, Z. et al. Al-doped α-MnO2 for high mass-loading pseudocapacitor with excellent cycling stability. Nano Energy 11, 226–234 (2015).

  45. 45.

    He, Y. et al. Freestanding three-dimensional graphene/MnO2 composite networks as ultralight and flexible supercapacitor electrodes. Acs Nano 7, 174–182 (2013).

Download references


The authors gratefully acknowledge the financial support by National Natural Science Foundation of China (51271205, 50801070, 51571093), Excellent Young College Teachers Development Program in Guangdong Province (Yq2013006), Research and Application of Key Technologies Oriented the Industrial Development (90035–3283309, 90035–3283321), the Fundamental Research Funds for the Central Universities (2015ZM094,16lgjc63), “Project of Science and Technology Plan” by Guangzhou city (2013Y2-00102), by Huizhou city (2012B050013012), by DaYa Gulf district in Huizhou city (20110108, 20120212).

Author information


  1. School of Mechanical and Automotive Engineering, South China University of Technology, Guangzhou, 510640, China

    • Jie Zhao
  2. Key Laboratory for Polymeric Composite & Functional Materials of Ministry of Education, School of Chemistry, Sun Yat-sen University, Guangzhou, 510275, China

    • Xilai Zou
    • , Peng Sun
    •  & Guofeng Cui
  3. Key Laboratory of Low-carbon Chemistry & Energy Conservation of Guangdong Province, Sun Yat-sen University, Guangzhou, 510275, China

    • Xilai Zou
    • , Peng Sun
    •  & Guofeng Cui


  1. Search for Jie Zhao in:

  2. Search for Xilai Zou in:

  3. Search for Peng Sun in:

  4. Search for Guofeng Cui in:


J.Z. analyzed the data and wrote the manuscript. X.Z. and P.S. synthesized the materials and performed the sample measurements. All authors have given approval to the final version of the manuscript. G.C. designed and directed the work, discussed the results.

Competing Interests

The authors declare that they have no competing interests.

Corresponding authors

Correspondence to Jie Zhao or Guofeng Cui.

Electronic supplementary material


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

Creative Commons BY

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit