Abstract
Tribotronics has attracted great attention owing to the demonstrated triboelectrification-controlled electronics and established direct modulation mechanism by external mechanical stimuli. Here, a nanoscale triboelectrification-gated transistor has been studied with contact-mode atomic force microscopy and scanning Kevin probe microscopy. The detailed working principle was analyzed at first, in which the nanoscale triboelectrification can tune the carrier transport in the transistor. Then with the manipulated nanoscale triboelectrification, the effects of contact force, scan speed, contact cycles, contact region and charge diffusion on the transistor were investigated, respectively. Moreover, the manipulated nanoscale triboelectrification serving as a rewritable floating gate has demonstrated different modulation effects by an applied tip voltage. This work has realized the nanoscale triboelectric modulation on electronics, which could provide a deep understanding for the theoretical mechanism of tribotronics and may have great applications in nanoscale transistor, micro/nano-electronic circuit and nano-electromechanical system.
Similar content being viewed by others
Introduction
With the development of micro/nano-technology, electronics are expected to be more miniaturized1,2,3, multifunctional4,5,6, and intelligent7,8,9 to promote the information technology advancement. By integrating micro/nano-electronics into multifunctional micro/nano-systems and large-scale networks for environmental monitoring10,11,12, human-machine interfacing13,14,15, biomedical diagnosis/therapy16,17,18,19, and so on, everything could be connected to the Internet for information interaction and intelligent identification in the future20. However, the interaction mechanisms between most of the micro/nano-electronics and human/environment are passive so far, which greatly limits the information acquisition21. Therefore, it is highly desired for micro/nano-electronics to establish active interactions with the external stimuli to achieve direct information acquisition.
Triboelectric nanogenerator (TENG) as an emerging energy technology has been invented by Wang in 201222,23, which could convert a variety of mechanical motions into electrical outputs based on the conjugation effects of triboelectrification and electrostatic induction24,25,26,27,28. In recent years, by coupling the triboelectricity and semiconductor properties, tribotronics, as an emerging research field has been proposed, which has demonstrated various triboelectrification-controlled electronics and established direct modulation mechanism by external mechanical stimuli29,30,31,32. However, the interactive interfaces between external environment and electronics in current tribotronic devices are all in the macro scale, which has limited the integration and modularization of tribotronics. When the size scales down to the micro or nano range, whether the modulation effect still exists is a critical question for tribotronics.
In this work, a nanoscale triboelectrification-gated transistor (NTT) has been studied with contact-mode atomic force microscopy (AFM) and scanning Kevin probe microscopy (SKPM). The detailed working principle was analyzed at first, in which the nanoscale triboelectrification generated on the top dielectric layer by AFM tip can tune the carrier transport in the NTT. Then with the manipulated nanoscale triboelectrification by AFM, the effects of contact force, scan speed, contact cycles, contact region and charge diffusion on the characteristics of the NTT were investigated, respectively. Moreover, the manipulated nanoscale triboelectrification serving as a rewritable floating gate has demonstrated different modulation effects on the NTT by an applied tip voltage. This work has experimentally realized the nanoscale triboelectric modulation on transistor by using AFM and demonstrated micro/nano-scale tribotronics, which could provide a deep understanding for the theoretical mechanism of tribotronics. The implementation of the NTT can provide direct interactions of electronics with external stimuli, which is highly desired for the development of micro/nano-electronics in diversity and functionality. This may have great prospects in nanoscale transistor, micro/nano-electronic circuit and nano-electromechanical system (NEMS) for human-machine interfacing, flexible electronics, biomedical diagnosis/therapy and so on.
Results
Mechanism of the NTT
As schematically illustrated in Fig. 1a, the basic structure of NTT is similar to the traditional metal oxide semiconductor field-effect transistor (MOSFET) without the top gate electrode. And, the top silicon dioxide (SiO2) layer is rubbed by an AFM tip which has a radius of 20–40 nm (Fig. 1b) to ensure the contact area is in nanoscale during the process of triboelectrification. The scanning electron microscope (SEM) images of the NTT in cross-sectional view are shown in Fig. 1c. The test method for NTT is stated as follows. First, the channel region (5 × 5 μm) of the NTT is located with tapping-mode AFM (Fig. 1d). Then, the AFM is switched into the contact mode to scan and rub the top SiO2 surface above the channel region for nanoscale triboelectrification (Fig. 1e). Subsequently, the nanoscale triboelectrification could be quantitatively characterized by measuring the potential distribution of the top SiO2 surface using SKPM (Fig. 1f, g). The electrical characteristics of the NTT are constantly monitored during the whole process to obtain the nanoscale triboelectrification tuned properties.
The working principle of the NTT is illustrated with cross-sectional schematics in Fig. 1h, which could be mainly divided into two stages. During the process of nanoscale triboelectrification, the top SiO2 surface above the channel region is scanned and rubbed by the AFM tip in contact mode. Based on the electron transfer mechanism, electrons from the AFM tip could transfer onto the top SiO2 surface, because the AFM tip used in this work is silicon (Si) probe, which has a smaller effective work function than SiO2. After contact procedure, considerable transferred charges are bound on the top SiO2 surface, resulting in an inner electric field at the channel region, which can attract holes and repel electrons in the P-type silicon (P-Si) layer. Therefore, the concentration of holes as majority carriers at the channel region is enhanced, leading to the formation of enhancement zone, which could increase the drain current Id of NTT.
The energy band diagrams in the vertical direction of the channel region are also utilized to analyze the working mechanism of NTT. As shown in Supplementary Fig. 1, W is the effective work function of the Si probe, E0 is the difference between vacuum level Evcc and the highest filled surface energy states of SiO2. Thus, the Fermi level of the Si probe is above the highest filled surface energy states of SiO2 in the initial state (Supplementary Fig. 1a). Meanwhile, we define a threshold distance z below which electrons could transfer between two surfaces, and above z the barrier is large enough to prevent any tunneling. After contact (Supplementary Fig. 1b), electrons from the Si probe have flowed to the top SiO2 to fill up the surface states as high as the Fermi level of Si. At this time, a built-in electrical field applied on the SiO2 and P-Si layers is formed due to the transferred electrons on the top SiO2 surface, which can upward bend the energy band of P-Si at the interface. Therefore, the concentration of holes in the valence band of P-Si is enhanced, which could induce the increase of drain current.
Characteristics of the NTT
The electrical properties of the transistor are first measured by applying an external bottom gate voltage Vbg (Supplementary Fig. 2a). The Id–Vbg transfer characteristics of the transistor with different Vbg from −30 V to 0 are shown in Supplementary Fig. 2b, which indicate that the drain current monotonously increases with increasing the negative bottom gate voltage, when the negative bottom gate voltage is more than around −17 V. And, drain current has the maximum enhancing speed at a bottom gate voltage of −22 V. Therefore, in order to make the drain current of NTT more sensitive to the nanoscale triboelectrification, a Vbg of −22 V is applied in the following experiments for optimizing test method. The equivalent test circuit diagram is shown in Supplementary Fig. 3.
The effect of contact force F on the characteristics of the NTT is first investigated. In this experiment, the top SiO2 surface above the channel region was scanned by the AFM tip once at a scan speed of 10 μm/s. As shown in Supplementary Fig. 4a-c, the changed top SiO2 surface potential above the channel region ΔV is enhanced with the contact force increasing from 0 to 2.5 nN, and approximately reaches a saturated value of −1.48 V when the contact force is larger than 2 nN. The corresponding drain current Id of the NTT shows a similar trend following the increase of contact force, which is enhanced from 139 μA to 272 μA and reaches saturation when contact force is larger than 2 nN (Supplementary Fig. 4d–e). During the process of nanoscale triboelectrification, the increasing contact force can decrease the potential barrier and induce more electrons to transfer onto the SiO2 surface, until reaching the saturation state when the highest filled surface energy state of SiO2 is as high as the Fermi level of Si. In Supplementary Fig. 4, as the contact force increases in the low range, more charges are transferred that leads to the rise of the highest filled surface energy state of SiO2. When the contact force increases to 2 nN, the amount of transferred charges is large enough to make the highest filled surface energy state of SiO2 almost as high as the Fermi level of Si. So, the contact force larger than 2 nN will hardly lead to more transferred charges, and the KPFM contrast shows the fast saturation.
Then we have investigated the effect of scan speed v on the characteristics of the NTT. In this experiment, the top SiO2 surface above the channel region was scanned by the AFM tip once at a contact force of 1 nN. The changed top SiO2 surface potential above the channel region ΔV is enhanced as the scan speed decreases from 16 μm s−1 to 2 μm s−1, and reaches saturation when scan speed decreases to 4 μm s−1 (Supplementary Fig. 5a–c). The corresponding Id output characteristics also shows an increasing trend with the decreasing of scan speed, and reaches a saturated value of 272 μA when the scan speed is less than 4 μm s−1 (Supplementary Fig. 5d–e). A possible reason is that the decreasing scan speed could allow better contact between the AFM tip and the SiO2 surface until a very low speed, enabling more charges to be transferred onto the SiO2 surface. In addition, the contact force and scan speed are fixed to 1 nN and 10 μm s−1, respectively, in all the next experiments.
According to the previous work33, the transferred charge density σ on the dielectric layer surface is related to contact cycles n, which can be described by Eq. 1:
where σ0 is the surface charge density before contact; σ∞ is the saturated surface charge density after multiple contacts; n0 is the saturation constant that controls the saturation rate. Moreover, based on the parallel plate capacitance model, the changed top SiO2 surface potential above the channel region ΔV could be determined by Eq. 2:
where dSiO2 is the thickness of SiO2, ε0 and εSiO2 are the vacuum dielectric constant and the relative dielectric constant of SiO2, S is the charged area. In Eq. 2, ΔV is not related to S, which means that for the capacitive devices, the voltage generated by triboelectric charges is independent of area. This is meaningful to the miniaturization of tribotronics. Combining Eqs. 1 and 2, the relation between ΔV and n is shown in Eq. 3:
where V0 is the top SiO2 surface potential above the channel region before contact, V∞ is the saturated surface potential after multiple contacts. As for the NTT, the top gate voltage is equivalent to the top SiO2 surface potential above the channel region:
Therefore, in the ideal state the relation between Id and ΔV could be described by Eq. 5:
where W and L are the channel width and length of the NTT, μp is the hole mobility, Vt is the threshold voltage of the NTT. Combining Eqs. 3 and 4, the drain current of the NTT can be determined by Eq. 6:
The corresponding experimental results are shown in Fig. 2. First, the potential distributions of the top SiO2 surface after regionally rubbed by the AFM tip with increasing contact cycles are measured (Fig. 2a). Fig. 2b shows the measured potential distributions in cross-sectional view. And, Fig. 2c plots potential differences between the rubbed and surrounding area with different contact cycles, which fit Eq. 3 very well. By the synchronous electrical measurement of the NTT, drain current continuously increases from 139 μA to 257 μA during the process of nanoscale triboelectrification, as shown in Supplementary Fig. 6. Fig. 2d shows the Id output characteristics at a drain voltage of 5 V with increasing contact cycles from 0 to 3. And, Fig. 2e plots Id–n transfer characteristics of the NTT, which has a good aggrement with Eq. 6. The Id–Vd output characteristics with different contact cycles are shown in Fig. 2f. The experimental results indicate that the drain current is enhanced with increasing contact cycles and reaches to a saturation value of 280 μA, when the contact cycles is more than 2. The increasing contact cycles can induce more transferred charges and leads to the rise of the highest filled surface energy state of SiO2. According to Fig. 2, when the SiO2 surface is scanned twice by the AFM Si tip, the amount of transferred charges is large enough to make the highest filled surface energy state of SiO2 almost as high as the Fermi level of Si. So, the increasing contact cycles (more than 2) will hardly lead to more transferred charges, and the KPFM contrast shows the fast saturation.
Based on the test method for NTT, the contact region on the top SiO2 surface can be accurately controlled by AFM. This provides a direct method to study the influence of charged area of the top SiO2 surface on the electrical properties of NTT. As shown in Fig. 3a and Fig. 3b, the charged area can be effectively manipulated by changing the length l and width w of the contact region, respectively. The Id output characteristics at a drain voltage of 5 V with different contact lengths from 0 to 5 μm are shown in Fig. 3c. And, Fig. 3d depicts Id–l transfer curve of the NTT. Fig. 3e shows the Id–Vd output characteristics with different contact lengths. The experimental results indicate that as the contact length increases the drain current of the NTT is enhanced. Similar variation trend of drain current with increasing contact widths is shown in Fig. 3f–h. The difference is that the increasing rate of drain current with contact length is less than that with contact width in small region. This is because when the contact width is changed, the source and drain electrodes of the NTT remain connected by the charged area, thus the carrier transport channel always exists. By contrast, when the contact length is less than the channel length, the source and drain electrodes of the NTT are not connected by the charged area anymore, so the complete enhanced carrier transport channel no longer exists. Therefore, compared with the contact length, the contact width is more efficient in tuning the carrier transport of the NTT.
The transferred charges from the AFM tip cannot be bounded on the top SiO2 surface forever, and the surface diffusion of electrons is considered to exist. So, we have studied the effect of charge diffusion on the characteristics of the NTT in this work. The top SiO2 surface above the channel region is first scanned twice by the AFM tip in contact mode to ensure that the amount of transferred charges reaches saturation. Then the potential distribution of the top SiO2 surface and the electrical properties of the NTT are measured every 2 h. The potential distributions of the top SiO2 surface with different dissipation times t are shown in Fig. 4a. Fig. 4b depicts the corresponding potential distributions in cross-sectional view, which indicate that, as the dissipation time increases, the absolute value of potential difference between the rubbed and surrounding area is decreased and the area of charged region becomes larger at the same time. The synchronously measured Id output characteristics of the NTT at a drain voltage of 5 V with different dissipation times from 0 to 12 h are shown in Fig. 4c. And, Fig. 4d plots Id–t transfer curve. Fig. 4e shows the Id–Vd output characteristics of the NTT with different dissipation times. The experimental results indicate that with increasing dissipation time, the drain current of the NTT is reduced, and the reduction rate of the drain current is decreased. This is because as the dissipation time increases, the absolute value of potential difference between the rubbed and surrounding area is decreased, which is equivalent to the decreasing of negative top gate voltage, resulting in the reduction of drain current.
The rewritable floating gate for the NTT
The nanoscale triboelectrification has been demonstrated to be effectively manipulated by an applied electric field. In order to realize a variety of modulation effects on the electrical properties of the NTT, a tip voltage VT is applied during the process of nanoscale triboelectrification (Fig. 5a).
The energy band diagrams in the vertical direction of the channel region are utilized to illustrate the working mechanism of NTT with an applied tip voltage (Supplementary Fig. 7). When the tip voltage is negative (VT < 0), which can raise the Fermi level of Si probe, more electrons are transferred from the AFM tip to the top SiO2 layer to fill up the higher surface energy states. Thus, the built-in electric field applied on the top SiO2 and P-Si layers is enhanced, and the energy band of P-Si bends further upwards in the interface, leading to further enhancement of hole concentration in valence band and drain current of the NTT. On the contrary, a positive tip voltage can lower the Fermi level of the Si probe, reducing the number of electrons flowed from the AFM tip to the top SiO2 surface. As the positive tip voltage increases to a certain value (VT = VN), the Fermi level of Si probe can be as low as the highest filled surface states of SiO2. At this condition, no charge can flow between the AFM tip and the top SiO2 surface. When the tip voltage is more positive than the nullified voltage (VT > VN), electrons can flow reversely from the top SiO2 surface to the AFM tip. Therefore, a positive built-in electric field is applied on the top SiO2 and P-Si layers, resulting in downwards bend of the energy band of P-Si in the interface, so the hole concentration in valence band and drain current of the NTT are decreased.
According to the previous work34, the transferred charge density σ can be modulated by the tip voltage VT, which can be described by Eq. 7:
where e is the elementary charge, and \(\overline {N_s} (E)\) is defined as the averaged surface density of states. Combining Eqs. 2 and 6, we have
Further combining Eqs. 5 and 8, the relation between the drain current of the NTT and the tip voltage can be determined by Eq. 8:
This equation means that the drain current of the NTT can be effectively tuned in different ways by the tip voltage.
In the experiments, the effect of contact cycles on the characteristics of the NTT with an applied tip voltage is first measured. As shown in Supplementary Fig. 8, the amount of transferred charges on the top SiO2 surface and the drain current of the NTT saturate after rubbed by the AFM tip once at a tip voltage of −2 V. The potential distributions of the top SiO2 surface with increasing tip voltage are shown in Fig. 5b. Fig. 5c depicts the corresponding potential distributions in cross-sectional view. The potential difference between the rubbed and surrounding area almost linearly increases with the tip voltage, as shown in Fig. 5d. The Id output characteristics with different tip voltages from −10 V to 10 V are shown in Fig. 5e. And, Fig. 5f plots the Id–VT transfer characteristics of the NTT. The transfer curve of the NTT is saturated with the Id of 125 μA in the positive direction, and in the negative direction, the drain current shows a saturation trend and is almost saturated with a value of 443 μA. Fig. 5g shows the Id–Vd output characteristics with different tip voltages. Meanwhile, the modulation of ΔV and Id by the tip voltage are repeatable, which demonstrates a rewritable floating gate for the NTT. In addition, we have fabricated a top metal gate electrode on the transistor (Supplementary Fig. 9a-b). The corresponding Id–Vtg transfer curve is shown in Supplementary Fig. 9c, from which we can calculate the mobility (\(\mu {\mathrm{ = }}\frac{{Lg{}_{\mathrm{m}}}}{{WC_{{\mathrm{OX}}}V_{\mathrm{d}}}}\), where μ, gm, L, W and Cox are the mobility, transconductance, channel length, channel width and gate oxide capacitance), Ion/off ratio, and Vth as 193 cm2 V−1 s−1, 23 and 2.8 V, respectively. As for the NTT, the changed top SiO2 surface potential above channel region ΔV is considered as the actual voltage that applied on the top gate of the NTT by the AFM tip. Thus, we get the Id–ΔV transfer curve of the NTT to compare with the top metal gate transistor. According to the Id–VT curve shown in Fig. 5f, the Id–ΔV transfer curve of the NTT can be plotted as shown in Supplementary Fig. 9d, in which each ΔV corresponds to a tip voltage VT (Fig. 5d). The mobility, Ion/off ratio, and Vth of the NTT can be further calculated as 431 cm2 V−1 s−1, 4 and 1.1 V, respectively. As a contrast, there are a few differences on the mobility, Ion/off ratio, and Vth between top metal gate transistor and the NTT due to the stray capacitance of top metal gate, the residual charge after nanoscale triboelectrification and so on. However, both sets of values are comparable, which indicate that the top metal gate electrode can be replaced by nanoscale triboelectrification-gating. The effect of charge diffusion on the characteristics of the NTT with an applied tip voltage is also studied. The top SiO2 surface above the channel region is first scanned once by the AFM tip in contact mode at a tip voltage of −2 V. Then the potential distribution of the top SiO2 surface and the electrical properties of the NTT are measured every hour. As shown in Supplementary Fig. 10, the absolute value of potential difference between the rubbed and surrounding area is decreased and the area of charged region becomes larger with rising dissipation time. At the same time, the drain current of the NTT is reduced from 312 μA to 265 μA within 8 h.
Discussion
In summary, we have studied the tribotronic transistor gated by nanoscale triboelectrification with contact-mode AFM and SKPM. The detailed working principle was analyzed at first, in which the nanoscale triboelectrification generated on the top dielectric layer by AFM tip can tune the carrier transport in the NTT in a space of less than a few micrometers. Then, the effects of contact force, scan speed, contact cycles, contact region and charge diffusion on the characteristics of the NTT were investigated, and the results have shown a good agreement with the theoretical analysis. Moreover, the controllable nanoscale triboelectrification by an applied tip voltage can serve as a rewritable floating gate, which has demonstrated different modulation effects on the NTT. This work has realized the nanoscale triboelectric modulation on electronics, which could provide a deep understanding for the theoretical mechanism of tribotronics and may have great applications in nanoscale transistor, micro/nano-electronic circuit and NEMS.
Methods
Fabrication of the NTT
The detailed fabrication process of the NTT is shown in Supplementary Fig. 11. First, an SOI wafer with the sandwich structure was prepared, which has a top 380 nm thick P-Si layer, a buried 500 nm thick SiO2 layer and a bottom 500 μm thick P-Si. Then, part of the P-type channel layer was masked by lithography (M1) (SUSS MA/BA 6), and two heavily doped P+-Si areas were formed by Boron ion implantation (Varian 350). A layer of SiO2 with a thickness of 70 nm was formed by thermal oxidization (L4514II2F) on the top and bottom surfaces. The top SiO2 surface was next masked by lithography (M2), and the electrode areas were opened by inductively coupled plasma (ICP) etching the top SiO2 layer (STS Multiplex AOE). The top surface was masked again by lithography (M2), and two Aluminum (Al) pads with a thickness of 1 μm were deposited on the surface of P+-Si areas with Ohmic contacts by RF sputtering (Denton Discovery635) as the drain and source electrodes. At last, the bottom SiO2 layer was etched and a 1 μm thick Al layer was deposited on the surface of bottom P-Si layer serving as the bottom gate electrode.
Characterization of the NTT
First, Si probe was prepared by mechanically removing the Platinum (Pt) layer of the conductive probe (AC240TM from Olympus). More specifically, the probe was scanned on a sapphire film with a contact force of 600 nN for three cycles. The morphology of Si probe was characterized by Hitachi SU8020 with an acceleration voltage of 7 kV. Then a standardized focused ion beam (FIB) method was used to etch the channel region of the NTT (FEI Helios 600I), so that the cross-sectional view of the NTT can be characterized as shown in Supplementary Fig. 12. The measurement platform for the NTT was conducted in an MFP-3D AFM from Asylum Research at ambient environment with the relative humidity of 20–30%. In contact mode, the sensitivity of optical lever and spring constant of the cantilever are 197 nm V−1 and 0.9 N m−1, respectively. And the deflection of cantilever was set to be 0.005 V. Thus, the contact force was controlled as 1 nN during the process of nanoscale triboelectrification. The synchronous Id–Vd output characteristics of the NTT were performed by using a Keithley 4200 A semiconductor characterization system. And the transfer characteristics were measured by using an SR570 low-noise current amplifier (Stanford Research System) and a programmable DC power supply (RIGOL DP832).
Data availability
All data needed to evaluate the conclusions in the paper are present in the paper and/or the Supplementary Information. Additional data related to this paper may be requested from the authors. The source data underlying all figures can be found in the Source Data file.
References
Liu, C.-C. et al. Directed self-assembly of block copolymers for 7 nanometre FinFET technology and beyond. Nat. Electron. 1, 562–569 (2018).
Hui, F. & Lanza, M. Scanning probe microscopy for advanced nanoelectronics. Nat. Electron. 2, 221–229 (2019).
Fahad, H. M., Gupta, N., Han, R., Desai, S. B. & Javey, A. Highly sensitive bulk silicon chemical sensors with Sub-5 nm thin charge inversion layers. ACS Nano 12, 2948–2954 (2018).
Wang, C. et al. User-interactive electronic skin for instantaneous pressure visualization. Nat. Mater. 12, 899–904 (2013).
Chow, P. C. Y. et al. Dual-gate organic phototransistor with high-gain and linear photoresponse. Nat. Commun. 9, 1–8 (2018).
Bu, T. et al. Stretchable triboelectric–photonic smart skin for tactile and gesture sensing. Adv. Mater. 30, 1800066 (2018).
Kim, Y. et al. A bioinspired flexible organic artificial afferent nerve. Science 360, 998–1003 (2018).
Someya, T. & Amagai, M. Toward a new generation of smart skins. Nat. Biotechnol. 37, 382–388 (2019).
Shin, J. et al. Bioresorbable optical sensor systems for monitoring of intracranial pressure and temperature. Sci. Adv. 5, eaaw1899 (2019).
Xi, F. et al. Self-powered intelligent buoy system by water wave energy for sustainable and autonomous wireless sensing and data transmission. Nano Energy 61, 1–9 (2019).
Mercuri, M. et al. Vital-sign monitoring and spatial tracking of multiple people using a contactless radar-based sensor. Nat. Electron. 2, 252–262 (2019).
Binions, R. & Naik, A. J. T. Metal oxide semiconductor gas sensors in environmental monitoring. Semicond. Gas Sensors 433–466, https://doi.org/10.1533/9780857098665.4.433 (2013).
Wang, S. et al. Skin electronics from scalable fabrication of an intrinsically stretchable transistor array. Nature 555, 83–88 (2018).
Roh, E., Hwang, B. U., Kim, D., Kim, B. Y. & Lee, N. E. Stretchable, transparent, ultrasensitive, and patchable strain sensor for human-machine interfaces comprising a nanohybrid of carbon nanotubes and conductive elastomers. ACS Nano 9, 6252–6261 (2015).
Jeong, J. W. et al. Materials and optimized designs for human-machine interfaces via epidermal electronics. Adv. Mater. 25, 6839–6846 (2013).
Gao, W. et al. Fully integrated wearable sensor arrays for multiplexed in situ perspiration analysis. Nature 529, 509–514 (2016).
Gutruf, P. et al. Fully implantable optoelectronic systems for battery-free, multimodal operation in neuroscience research. Nat. Electron. 1, 652–660 (2018).
Lee, S. et al. Ultrasoft electronics to monitor dynamically pulsing cardiomyocytes. Nat. Nanotechnol. 14, 156–160 (2019).
Park, S. et al. Self-powered ultra-flexible electronics via nano-grating-patterned organic photovoltaics. Nature 561, 516–521 (2018).
Tao, F., Zuo, Y., Xu, L. Da & Zhang, L. IoT-Based intelligent perception and access of manufacturing resource toward cloud manufacturing. IEEE Trans. Ind. Inform. 10, 1547–1557 (2014).
Yang, Z. W. et al. Tribotronic transistor array as an active tactile sensing system. ACS Nano 10, 10912–10920 (2016).
Fan, F. R., Tian, Z. Q. & Lin Wang, Z. Flexible triboelectric generator. Nano Energy 1, 328–334 (2012).
Xu, L., Bu, T. Z., Yang, X. D., Zhang, C. & Wang, Z. L. Ultrahigh charge density realized by charge pumping at ambient conditions for triboelectric nanogenerators. Nano Energy 49, 625–633 (2018).
Wang, Z. L. On Maxwell’s displacement current for energy and sensors: the origin of nanogenerators. Mater. Today 20, 74–82 (2017).
Zhang, C., Tang, W., Han, C., Fan, F. & Wang, Z. L. Theoretical comparison, equivalent transformation, and conjunction operations of electromagnetic induction generator and triboelectric nanogenerator for harvesting mechanical energy. Adv. Mater. 26, 3580–3591 (2014).
Liu, J. et al. Direct-current triboelectricity generation by a sliding Schottky nanocontact on MoS2 multilayers. Nat. Nanotechnol. 13, 112–116 (2018).
Liu, J. et al. Sustained electron tunneling at unbiased metal-insulator-semiconductor triboelectric contacts. Nano Energy 48, 320–326 (2018).
Liu, J. et al. Separation and quantum tunneling of photo-generated carriers using a tribo-induced field. Matter 1, 650–660 (2019).
Zhang, C. et al. Tribotronics for active mechanosensation and self-powered microsystems. Adv. Funct. Mater. 29, 1808114 (2019).
Zhang, C. & Wang, Z. L. Tribotronics—A new field by coupling triboelectricity and semiconductor. Nano Today 11, 521–536 (2016).
Zhang, C., Tang, W., Zhang, L., Han, C. & Wang, Z. L. Contact electrification field-effect transistor. ACS Nano 8, 8702–8709 (2014).
Xi, F. et al. Tribotronic bipolar junction transistor for mechanical frequency monitoring and use as touch switch. Microsyst. Nanoeng. 4, 25 (2018).
Zhou, Y. S. et al. In situ quantitative study of nanoscale triboelectrification and patterning. Nano Lett. 13, 2771–2776 (2013).
Zhou, Y. S. et al. Manipulating nanoscale contact electrification by an applied electric field. Nano Lett. 14, 1567–1572 (2014).
Acknowledgements
The authors thank the support of the National Natural Science Foundation of China (Nos. 51922023, 51605033, 61874011), Beijing Natural Science Foundation (No. 4192070).
Author information
Authors and Affiliations
Contributions
T.B., L.X., C.Z., and Z.L.W. conceived the idea and designed the experiment. T.B. and L.X. carried out the nanoscale triboelectrification-gated transistor experiments. Z.Y. and X.Y. contributed to the device fabrication. G.L. and Y.C. helped with the data analysis. T.B., L.X., and C.Z. wrote the paper. All the authors discussed the results and commented on the paper.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Peer review information Nature Communications thanks the anonymous reviewers for their contribution to the peer review of this work. Peer reviewer reports are available.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Source Data
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Bu, T., Xu, L., Yang, Z. et al. Nanoscale triboelectrification gated transistor. Nat Commun 11, 1054 (2020). https://doi.org/10.1038/s41467-020-14909-6
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-020-14909-6
This article is cited by
-
High-performance hybrid nanogenerator for self-powered wireless multi-sensing microsystems
Microsystems & Nanoengineering (2023)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.