Abstract
Inspired by the repair of DNA through efficient reformation of hydrogen bonds (H-bonds), herein we report a facile one-step approach to construction of self-healing antifogging thin films on the basis of partly cross-linked poly(vinyl alcohol)(PVA) and poly(acrylic acid)(PAA). By designing the molar ratio of hydroxyl groups to carboxyl groups, the cross-linked polymer thin films maintain abundant free hydroxyl groups to present excellent antifogging property, which is derived from the hydrophilicity and hygroscopicity of the thin films. The thin films showed smart intrinsic self-healing characteristics towards wounds caused by external forces, which is attributed to sufficient free hydroxyl groups at the scratched interfaces to reform H-bonds across the interfaces and a sufficient chain mobility that is indispensable for chain diffusion across the interfaces and hydroxyl groups association to form H-bonds. No synthetic surfaces reported so far possess all the unique characteristics of the polymer thin films: intrinsic self-healing, long-term antifogging, excellent mechanical property, high transmittance and large-scale feasibility.
Similar content being viewed by others
Introduction
It is well known that in biological systems, DNA has repair capability while tissues and organs have regenerative power. Although there is currently no analog in synthetic materials, the phenomenon of self-healing in biological systems has inspired huge research interest and the fabrication of artificial self-healing materials has become an appealing strategy in consideration of lifetime and damage managements1,2,3,4. For example, White5 et al. developed a vascular repair system that can fill and polymerize a defect 10 mm in diameter and 3 mm thick. However, the integrity of repaired defects is not known and the repaired sites do not have the same composition as the native polymer. Therefore, intrinsic self-healing is an appealing strategy of damage management compared with extrinsic self-healing. Inspired by Nepenthes, Aizenberg6 et al. designed a film of lubricating liquid locked in place by micro/nanoporous substrate, providing immediate self-repair through capillary wicking derived from perfluorinated fluid, which unfortunately has limits for long term operation due to the volatility of perfluorinated fluid. In nature, self-healing can occur at the level of single molecules such as the repair of DNA7. The formation and breaking of H-bonds between proteins and nucleic acids have been found to be a vital factor in the process of repairing oxidative damage to the purines8,9. Inspired by the repair of DNA through the efficient reformation of H-bonds, we herein report a facile one-step approach to construction of self-healing antifogging thin films based on partly cross-linked poly(vinyl alcohol)(PVA) and poly(acrylic acid)(PAA).
Owing to the design of the 3:1 ~ 1.45:1 molar ratio between hydroxyl groups and carboxyl groups, even after the esterification reaction of PVA and PAA, the polymer maintains enough free hydroxyl groups to ensure efficient reformation of H-bonds. The efficient intrinsic self-healing of the thin films is attributed to enough free hydroxyl groups at the scratched interfaces to reform H-bonds across the interfaces and a sufficient chain mobility that is indispensable for chain diffusion across the interfaces and hydroxyl groups association to form H-bonds10,11. Excellent antifogging property was observed and is derived from the hydrophilicity and hygroscopicity of the thin films12. No synthetic surfaces reported so far possess all the unique characteristics of the polymer thin films: intrinsic self-healing, long-term antifogging, excellent mechanical property, high transmittance and large-scale feasibility.
The smart design and facile fabrication of the polymer thin films, which were inspired by the self-repair of the DNA damage is a breakthrough and introduction to the device of multifunctional thin films, in consideration of lifetime and damage managements. This notion would stand out as a forerunner to the materials design of our age and future.
Results and Discussion
Self-healing property
Thin films were deposited on substrates by one step dip-coating in an aqueous solution containing PVA and PAA with a 3:1 ~ 1.45:1 molar ratio between hydroxyl groups and carboxyl groups followed by thermal treatment at 130–150°C for 5 min. Top-view scanning electron microscopy (SEM) images show that the thin film is in fact very smooth and scratches (Fig. 1a) created by 6H pencil could self-heal within a few minutes under appropriate environmental temperature and humidity (Fig. 1b). The efficient intrinsic self-healing of the thin film is attributed to sufficient free hydroxyl groups at the scratched interfaces to reform H-bonds across the interfaces and a sufficient chain mobility that is indispensable for chain diffusion across the interfaces and hydroxyl groups association to form H-bonds10,11, as schematically illustrated in Fig. 2a. Attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR)(Fig. 2b) analysis of the thin film shows two characteristic peaks, of which the broad band at 3300 cm−1 is attributed to the hydroxyl group and the band at 1703 cm−1 originates from the carbonyl group of ester. Clearly, even after the esterification reaction, the polymer maintains sufficient free hydroxyl groups to ensure the efficient reformation of H-bonds thanks to the design of the molar ratio between hydroxyl groups and carboxyl groups.
Antifogging property
The thin film was found to exhibit excellent antifogging behavior. As shown in Figure 3a, when a substrate partly coated by the polymer was cooled at −6°C for 24 h in a refrigerator and then exposed to humid laboratory air (relative humidity (RH): 20%–40%), the uncoated part fogged immediately and the words below were blurred by strong light scattering of tiny water droplets. In contrast, the polymer-coated part remained highly transparent and the words below were clearly visible. The antifogging mechanism was investigated by ATR-FTIR and quartz crystal microbalance (QCM). Fig. 3b shows the ATR-FTIR spectra of the polymer-coated substrate recorded before and after the antifogging test, respectively. The ATR-FTIR spectra were normalized based on the unchanged peak intensity of –CH2.
The sharp increase of the peak at 3262 cm−1 means the increase of the amount of hydroxyl groups after the antifogging test and the increased hydroxyl groups derive from the absorbed water by the polymer thin film preventing fogging on the polymer thin film, while the water droplets condensate on the blank glass. The absorption of water molecules must give rise to a corresponding mass change. The mass change of polymer thin film arising from the antifogging test was monitored by QCM. The QCM measurements indicate that the amount of water absorbed by the polymer (3.56 × 10−9 g) was 1.71 × 10−10 g. Therefore, the thin film weight increased by nearly 4.80 wt% because of the absorption of water molecules. According to the QCM results, if we assume one H-bond for one water molecule, the amount of H-bonds in 1 g polymer thin film is at least 2.67 × 10−3 mol. On the basis of the experimental results, a plausible antifogging mechanism was proposed for the polymer thin films. When water molecules in moist air from a warmer environment starts to condensate on the antifogging surface, the water molecules are rapidly absorbed into the hydrophilic domains of the polymer by hydrogen bonding and dipole-dipole interaction, preventing microdroplets from forming on the thin film surface. The absorbed water molecules may exist in the nonfreezing state13,14. According to the results on the states of water in different hydrophilic polymers by Ping14, in the case of PVA, the water could be kept liquid even at −100°C when the PVA concentration reaches 80% (w/w). And, our partly cross-linked PVA/PAA thin film maintains sufficient hydroxyl groups and thus the hyrophilic property. Through the interaction of water molecules and hydroxyl groups, the absorbed water by the polymer thin film must have been kept liquid at −6°C which is supported by the repeated antifogging tests. The thin film also remained transparent in the refrigerator even after absorbing water from the moist environment. And recent work by Wang15,16,17 also illustrated that the aqueous lubricating layer can be formed on the water swollen polymer with excellent anti-icing property.
The initial contact angle (CA) of the thin film surface was 62° (Figure 3c), demonstrating that a thin film does not have to be superhydrophilic to be effectively antifogging12. In the absence of long-range interfacial forces, the current understanding of wetting typically centers upon two key results: Young's law for wetting on rigid substrates and Neumann's triangle for wetting on liquid substrates. On soft solids, the total free energy includes an additional contribution from elasticity18,19,20. And with regard to the hygroscopicity of the polymer films, Young's law fails when there is substantial deformation near the three-phase contact line12.
Optical and mechanical properties
The transmission spectra of blank glass substrate and polymer-coated glass substrate are shown in Figure 4a. The thin film only lowers the transmittance slightly as compared with blank glass substrate. Thus the thin film is highly transparent.
Mechanical properties of thin films are a key issue21, especially for outdoor applications. The mechanical properties of prepared thin films were assessed by washability and adhesion-to-substrate. The thin film was washed for up to 50 cycles using a sponge at a speed of 50 cycles per minute. If a thin film is not washed off, it is believed to have good washability and can endure practical washing. After washing, the thin film was kept intact only with a slight decrease in transmittance (Fig. 4b) and it also maintained the excellent antifogging property (Fig. 4c). Tape peeling test was applied to examine the adhesion-to-substrate of thin film. It was carried out by first pressing 3 M Scotch tape (cat.600) on and then peeling off the thin film. One hundred peeling tests were applied and after the tape peeling tests, the thin film was still attached firmly to the substrate surface and maintained the excellent antifogging property (Fig. 4d). Therefore, the current thin films show excellent mechanical properties.
This polymer thin film could also be applied on flexible substrates such as poly(ethylene terephthalate)(PET). The corresponding antifogging, optical and mechanical properties are shown in the Supporting Information.
Conclusion
DNA inspired self-healing antifogging thin films have been developed successfully. These smart polymer thin films exhibit intrinsic self-healing characteristics, outstanding long-term antifogging property, high transmittance, excellent mechanical robustness, strong adhesion to substrate and large-scale feasibility. To our best knowledge, no synthetic surfaces reported so far possess all the unique characteristics simultaneously. The criteria towards such smart polymer thin films include: (1) an appropriate molar ratio of the hydroxyl groups of PVA to the carboxyl groups of PAA in order to maintain necessary hydrophilicity and sufficient free hydroxyl groups even after esterification and (2) cross-linking of PVA and PAA, which is essential to achieve excellent mechanical robustness and stability toward water. The current success in constructing intrinsic self-healing antifogging thin films would have broad technological implications such as eyeglasses, goggles, lenses, mirrors and display devices in analytical and medical instruments. Doubtlessly, the smart design and facile fabrication of polymer thin films, which were inspired by the self-repair of the DNA damage, is a breakthrough and introduction to the device of multifunctional thin films in consideration of lifetime and damage managements. This notion would stand out as a forerunner to the materials design of our age and future.
Methods
Chemicals
Poly(vinyl alcohol)(PVA, Mn = 70000–90000 g/mol, 99% hydrolyzed, Aladdin) and poly (acrylic acid) (PAA, 53 wt% in water, Mw = 4000–7000) were purchased from Shandong Heli water treatment company. Ultrapure water with a resistivity higher than 18.2 MΩ·cm was used in all experiments and was obtained from a three-stage Millipore Mill-Q Plus 185 purification system (Academic).
Thin film preparation
Thin films were depoisited on substrates by one-step dip-coating followed by thermal cross-linking. First, glass and poly(ethylene terephthalate)(PET) substrates were sonicated in water for at least 10 min and then treated with oxygen plasma (84 W, 5 min) at an oxygen flow of 800 mL·min−1. The substrates were then immersed in an aqueous solution containing PVA and PAA for 40 s, where the molar ratio of hydroxyl groups to carboxyl groups was set to 3:1 ~ 1.45:1 (RH: 15–40%) and withdrawn at a speed of 50 mm·min−1 from the solution. Finally, the thin films were thermally cross-linked at 130–150°C for 5 min.
Characterization of thin films
The as-prepared thin films were examined by scanning electron microscopy (SEM) on a Hitachi S-4300 scanning electron microscope operated at 5 kV. Water contact angles on thin films were measured at ambient temperature on a JC2000C contact angle/interface system (Shanghai Zhongchen Digital Technique Apparatus Co.). The angle precision of which is ±0.5°. Water droplets of 4 μl were dropped carefully onto the thin film surfaces. Transmission spectra in the wavelength range of 300–900 nm were recorded using a TU-1901 spectrophotometer (Beijing Purkinje General Instrument Co.). Washability was assessed by an Elcometer 1720 Abrasion Tester. Attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR) analyses were carried out on a Varian Excalibur 3100 spectrometer. The mass change of the thin film arising from the antifogging test was monitored by quartz crystal microbalance (QCM). A drop-coating method was used to coat both sides (5 mm in diameter) of a silver-coated QCM resonator (9 Hz, AT-cut piezoelectric quartz crystal, Beijing Chenjing Electronics) followed by thermal cross-linking. Frequencies were recorded by Agilent 53131A universal counter linked to a computer. For the examination of antifogging property, the substrate with thin film was cooled at ca. −6°C for 24 h in a refrigerator and then exposed to humid laboratory air (room temperature: 20–30°C, relative humidity: 20–40%).
References
Zhang, Y., Broekhuis, A. A. & Picchioni, F. Thermally self-healing polymeric materials: the next step to recycling thermoset polymers? Macromolecules 42, 1906–1912 (2009).
Amarnath, V. et al. Intermediates in the paal-knorr synthesis of pyrroles. J. Org. Chem. 56, 6924–6931 (1991).
Bergman, S. D. & Wudl, F. Mendable polymers. J. Mater. Chem. 18, 41–62 (2008).
Buchwalter, S. L. & Kosbar, L. L. Cleavable epoxy resins: design for disassembly of a thermoset. J. Polym. Sci., Part A. 34, 249–260 (1996).
White, S. R. et al. Restoration of large damage volumes in polymers. Science 344, 620–623 (2014).
Wong, T. S. et al. Bioinspired self-repairing slippery surfaces with pressure-stable omniphobicity. Nature 477, 443–447 (2011).
Hager, M. D., Greil, P., Leyens, C., van der Zwaag, S. & Schubert, U. S. Self-Healing Materials. Adv. Mater. 22, 5424–5430 (2010).
Norman, D. P. G., Chung, S. J. & Verdine, G. L. Structural and biochemical exploration of a critical amino acid in human 8-oxoguanine glycosylase. Biochem. 42, 1564–1572 (2003).
Tang, K., Sun, H., Zhou, Z. & Wang, Z. Density functional theory study on hydrogen-bonded complexes of adenine with polyformamide molecules. Int. J. Quantum Chem. 108, 1287–1293 (2008).
Spoljaric, S., Salminen, A., Luong, N. D. & Seppala, J. Stable, self-healing hydrogels from nanofibrillated cellulose, poly(vinyl alcohol) and borax via reversible crosslinking. Eur. Polym. J. 56, 105–117 (2014).
Zhang, H., Xia, H. & Zhao, Y. Poly(vinyl alcohol) hydrogel can autonomously self-heal. Acs Macro Letters 1, 1233–1236 (2012).
Lee, H., Alcaraz, M. L., Rubner, M. F. & Cohen, R. E. Zwitter-wettability and antifogging coatings with frost-resisting capabilities. Acs Nano. 7, 2172–2185 (2013).
Zhao, J., Meyer, A., Ma, L. & Ming, W. Acrylic coatings with surprising antifogging and frost-resisting properties. Chem. Commun. 49, 11764–11766 (2013).
Ping, Z. H., Nguyen, Q. T., Chen, S. M., Zhou, J. Q. & Ding, Y. D. States of water in different hydrophilic polymers−DSC and FTIR studies. Polymer 42, 8461–8467 (2001).
Chen, J. et al. Robust Prototypical Anti-icing Coatings with a Self-lubricating Liquid Water Layer between Ice and Substrate. Acs Appl. Mater. Interfaces 5, 4026–4030 (2013).
Chen, J., Luo, Z., Fan, Q., Lv, J. & Wang, J. Anti-Ice Coating Inspired by Ice Skating. Small 10, 4693–4699 (2014).
Dou, R. et al. Anti-icing Coating with an Aqueous Lubricating Layer. Acs Appl. Mater. Interfaces 6, 6998–7003 (2014).
Style, R. W. & Dufresne, E. R. Static wetting on deformable substrates, from liquids to soft solids. Soft Matter 8, 7177–7184 (2012).
Duprat, C., Protiere, S., Beebe, A. Y. & Stone, H. A. Wetting of flexible fibre arrays. Nature 482, 510–513 (2012).
Eslami, F. & Elliott, J. A. W. Thermodynamic investigation of the barrier for heterogeneous nucleation on a fluid surface in comparison with a rigid surface. J. Phys. Chem. B. 115, 10646–10653 (2011).
Xu, L. & He, J. A novel precursor-derived one-step growth approach to fabrication of highly antireflective, mechanically robust and self-healing nanoporous silica thin films. J. Mater. Chem. 1, 4655–4662 (2013).
Acknowledgements
This work was financially supported by a Chinese Academy of Sciences Grant (CXJJ-14-M38), the National High Technology Research and Development Program ("863" Program) of China (Grant No. 2011AA050525), the Knowledge Innovation Program of the Chinese Academy of Sciences (CAS) (Grant Nos. KGCX2-YW-370, KGCX2-EW-304-2) and the National Natural Science Foundation of China (Grant no. 21271177). The authors are very grateful to Mr. Binbin Jin for his help in the preparation of the schematic illustration of the self-healing procedure and to Dr. Mingqing Yang and Mr. Zhenqiang Wang for their help in the QCM measurements.
Author information
Authors and Affiliations
Contributions
J.H. designed the research and supervised the whole project. X.Z. designed the research, prepared samples and performed experiments with input from J.H. J.H. and X.Z. wrote the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Electronic supplementary material
Supplementary Information
Supplementary Material for Hydrogen-Bonding-Supported Self-Healing Antifogging Thin Films
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article's Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder in order to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Zhang, X., He, J. Hydrogen-Bonding-Supported Self-Healing Antifogging Thin Films. Sci Rep 5, 9227 (2015). https://doi.org/10.1038/srep09227
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep09227
This article is cited by
-
Hydrophilic nano-SiO2/PVA-based coating with durable antifogging properties
Journal of Coatings Technology and Research (2020)
-
Excellent self-healing and antifogging coatings based on polyvinyl alcohol/hydrolyzed poly(styrene-co-maleic anhydride)
Journal of Materials Science (2019)
-
In Situ Nanopressing: A General Approach to Robust Nanoparticles-Polymer Surface Structures
Scientific Reports (2016)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.