Introduction

Most human activities such as sports, industrial tasks, and daily living activities require dynamic endurance because most muscles are required to work continuously to accomplish these activities1,2,3. The limit of human endurance during a physical task is usually decided by the point at which an individual is unwilling or unable to continue the physical task, and this point is referred to as the point of ‘exhaustion’ or ‘fatigue’4,5. Muscular endurance is thus the measurement of an individual’s level of stamina or fatigue, and it may be limited by numerous physiological, biomechanical, mechanical, and psychological factors6,7,8. Many investigators have defined neuromuscular fatigue as a decreased performance under certain conditions9,10. During dynamic movement, neuromuscular fatigue can be directly assessed by any exercise-induced reduction in the ability to generate power or quantified as a time-dependent loss in power output11,12,13,14. Furthermore, recording surface electromyography (sEMG) during activities is useful to assess and understand muscle fatigue or endurance involved in muscle excitation, recruitment, and contraction12,15,16,17. Hence, sEMG is commonly used as an indirect and non-invasive method for assessing neuromuscular fatigue alongside mechanical variables (e.g., losses of force, torque, or power output)12,18. Furthermore, psychological fatigue is often incorporated as a part of the neuromuscular model of fatigue because fatigue is a psychophysiological symptom underpinned by interactions between performance fatigability and perceived fatigability8,19,20. Psychological alterations and perceived exertion determine the unconscious perception of fatigue, which can reduce power output and lead to the point of exhaustion6,8,21.

Specifically, power output, a combination of dynamic torque and joint angular velocity, and the duration of repetitive contractions are the two key contributors to dynamic endurance22,23,24. Thus, the retentive capacity of muscular power output is of great importance to most kinds of movements2,14. In previous studies, the isometric, isokinetic, or isotonic modes on dynamometers have been used to test muscular power2,3,25,26. Isotonic testing is considered to be more relevant to normal voluntary contractions, as the load is held constant but the velocity can vary27,28, which allows for the measurement of normal human movements during both acceleration and deceleration without controlling the angular velocity and acceleration25,27,28,29. Therefore, the isotonic testing protocol and database of muscular endurance is more applicable to the evaluation of sports science, rehabilitation medicine, and human-factor engineering. Moreover, the relationship between sEMG and power loss is useful for assessing and understanding neuromuscular fatigue, as it can be defined on the basis of electrophysiological or mechanical events30,31,32,33, and linear techniques are often used to estimate muscle fatigue by relating changes in sEMG parameters to changes in power loss. However, myoelectric signals can be better modeled as outputs of a non-linear dynamic system rather than as random stochastic signals, so a non-linear model based on a learning procedure would provide more accurate tracking of power loss using sEMG variables compared to a linear model12,31,34,35. Additionally, combining the subjective estimates of load tolerance and the subjects’ determinations of their own muscular endurance is beneficial for revealing the subjects’ real-world capacity during muscular endurance experiments20,36, and the results can help balance the workload and physical capacity to prevent acute or overuse injuries in actual application37,38. However, in many previous studies, subjects could not independently determine their load tolerance in dynamic fatiguing exercises, which involved fixed sets, repetitions, and rest times with the individual maximum load (e.g., repetition maximum, RM)15,30,31,32,33,39, so the actual muscle fatigue experienced by the subjects in those exercises may have exceeded their voluntary limits.

There is a limited amount of information regarding neuromuscular fatigue assessed during isotonic loading protocols. However, such protocols are the most suitable for measuring dynamic muscular endurance during the everyday movements of humans because these movements can be characterized by ballistic sinusoidal changes in velocity with constant loads rather than movements of constant velocity2,3. Therefore, in this study, the retentive capacity of muscular power output was assessed for the plantar flexors as well as the knee and hip extensors of college-aged males using an isotonic dynamometer and considering the subjective estimates of muscle fatigue. The isotonic endurance data of the lower limb muscles accumulated from the tests provide further insights into the relationships between human performance and muscle endurance required in real-world activities19,40. In addition, to guide the development of more effective electrophysiological evaluation methods of muscular fatigue, the accuracy of a fatigue linear model and a non-linear model were compared for their ability to relate sEMG variables to power loss during dynamic contractions.

Methods

Subjects

Subjects were recruited through advertisement and invitations to participate in the study in a non-random manner. The study was approved by the medical ethics committee of Jilin University and was performed in accordance with relevant guidelines and regulations of the institutional review board after each subject had given written informed consent, and all procedures performed in studies involving human participants were in accordance with the Declaration of Helsinki. Forty healthy college-aged males (age, 21.22 ± 1.10 years; height, 173.81 ± 3.44 cm; weight, 65.29 ± 6.49 kg; body mass index, 21.61 ± 2.09 kg/m2) with no previous history of lower extremity or severe musculoskeletal injury participated in the study.

Experimental procedure

A BTE Primus RS dynamometer (Dynatracä, BTE Co., Hanover, MD, USA) and Noraxon surface electromyography system (Noraxon, Inc. Scottsdale, AZ, USA) were used to collect data synchronously during the tests. Each subject performed a specific warm-up for the lower limbs and was familiarized with the experimental setup before the testing procedures. Next, each subject’s skin was dry-shaved and cleaned with alcohol. Then sEMG activity during the contractions of the right leg muscles was recorded from the medial gastrocnemius (MG), lateral gastrocnemius (LG), vastus medialis (VM), rectus femoris (RF), vastus lateralis (VL), gluteus maximus (GM), and biceps femoris (BF) by a pair of bipolar surface electrodes. Because the interelectrode distance influences the pick-up area, crosstalk, and signal spectrum41,42,43,44, the commonly used 22 mm spacing was selected for the interelectrode distance to enable quantitative comparisons of measured values with previous studies30,31,32.

The protocol consisted of three sets of isometric peak torque (IPT) tests and one set of an isotonic muscular endurance (IME) test for the plantar flexors and the knee and hip extensors (Fig. 1). The right ankle, knee, and hip of the subjects were aligned with the mechanical axis of rotation of the dynamometer in a reclining position, sitting position, and lying position. For the IPT test, three repetitions of maximum voluntary isometric contraction (MVC) were required, where each contraction lasted for 3 s, and there was a 5 s rest period between contractions. A coefficient of variation (CV) of less than 10% was required for the three contractions. Each subject performed gradually increasing isometric contractions with the ankle plantar flexed at 80°, knee extended at 110°, and hip extended at 90°. For the IME test, the resistance level was set to 50% of the subject’s average IPT, and the subject performed a complete repetition for each cycle according to a timing cycle (45–60 cycles/min) displayed on the screen. Specifically, the timing cycle asked subjects to match the pace of a red horizontal “pacing bar” and to keep the work rate the same for the duration of the test. The subjects were asked to keep their range of motion and pace of each cycle consistent and continued the repetitions until they were fatigued. Each subject performed repetitive concentric contractions in the ranges of 80°–130° for ankle plantar flexion, 80°–170° for knee extension, and 90°–180° for hip extension. Although a subject’s fatigue point was indicated by the dynamometer when the amount of power output recorded in two consecutive cycles was below 75% of the amount of power output generated during the first 5 s, verbal encouragement was also provided to motivate the subjects to continue with the test until they experienced fatigue and decided to stop.

Figure 1
figure 1

The change of angle, angular velocity, torque and power output with time during each cycle of the IME test for plantar flexors and knee and hip extensors. Note IME, isotonic muscular endurance. Each cycle included a limb loop in which a limb moves from the starting position to the ending position and then returns to the starting position. The angular presented a bell-curve, indicating that the limb loop moves from the starting position to the ending position, and then returns to the starting position. Correspondingly, with the two acceleration and deceleration movements of the limb segment, and the angular velocity presents two bell-shaped curves with opposite directions.

Full size image

Data acquisition and signal analysis

The length of lever arm (cm), force (N), and torque (N∙m) in three trials of the IPT test, and the work (J), time (s), and distance (°) in one trial of the IME test were recorded by BTE PrimusRS software. Both the sEMG signals and biomechanical signals such as time (s), torque (N∙m), angular position (°), and angular velocity (°/s) of the BTE PrimusRS dynamometer were recorded simultaneously by the TeleMyo 2400 T system (Noraxon, Inc., Scottsdale, AZ, USA) at a sampling rate of 1.5 kHz. Data analysis was performed offline using MATLAB 2014a software (MathWorks Inc., Natick, MA, USA).

Before acquiring the sEMG signal, an analog low-pass filter was used to suppress the high-frequency noise greater than 750 Hz in the system to eliminate the effect of its aliasing on the signal restoration. Then, a band-pass filter composed of a 5th-order high-pass filter and a 10th-order low-pass filter was adopted to digitally filter the collected sEMG signal to retain the frequency range of the signal within 20–250 Hz. Since wavelet transforms can realize the filtering function, wavelet transforms and the Hilbert transform were used when calculating IMNF and IMDF, and the cut-off frequency was 11.7188–350 Hz. In addition, the data of torque, angular position, angular velocity, and power output were smoothed by the adjacent averaging method. The angle of the limb segment increased from zero to the peak value or the positive bell-shaped part of the angular velocity, which was the concentric contractions phase of plantar flexors and knee and hip extensors (Fig. 1). The peak power output and sEMG parameters discussed in “Linear techniques used to estimate muscle fatigue”–“Time-dependent power output and power loss prediction” sections were calculated.

Linear techniques used to estimate muscle fatigue

Amplitude-based parameters and spectral parameters

Two main sEMG amplitude-based parameters, mean absolute value (MAV) and root mean square (RMS), were used to quantify the amplitude or magnitude of the sEMG signal12,28,45. Mean frequency (MNF) and median frequency (MDF) were estimated from the power spectrum using Fourier transform (FT). These two spectral parameters were used to quantify the changes in the spectral content of the sEMG signal12,13,17,30,45,46.

Instantaneous frequency parameters

The sEMG data were analyzed offline with a continuous wavelet transform (CWT) using MATLAB software with the signal processing and wavelet toolbox32,47. The Harr wavelet (db1 wavelet) was used as the mother wavelet, and the sEMG data were decomposed into six layers by the wavelet transform. The approximate scale of wavelet coefficients was retained, and the wavelet coefficients on the high-frequency details were removed to eliminate the clutter. The reserved wavelet coefficients were used to reconstruct the sEMG signal and complete the denoising process after the wavelet transform; the instantaneous mean and median frequency (IMNF and IMDF) of sEMG data were calculated by the Hilbert transform (HT)13,17,48,49.

Non-linear techniques used to estimate muscle fatigue

A multi-layer perception neural network (MLPNN) was chosen to relate changes in sEMG variables and power output because it shows good accuracy to relate sEMG variables and fatigue indices12,31,35. Four sEMG parameters were calculated from each contraction of all of the subjects: (1) MAV is an estimate of the mean absolute value of the signal, as the integrated EMG is divided by the integration time15,34,50; (2) zero crossing (ZC), as the number of times that the waveform crosses zero, is a simple measure of the main frequency of the signal15,34,50; (3) slope sign change (SSC), as the number of times that the slope of the waveform changes sign, provides another measure of frequency content15,34,50; and (4) wavelength (WL) provides information on the waveform complexity in each segment15,34,50. These parameters contain both amplitude and frequency information and have been shown to be useful in other sEMG pattern recognition applications15,31,51. The sEMG data were analyzed offline with MLPNN using MATLAB software with the signal processing and neural network toolbox. The training function adopted Levenberg–Marquardt backpropagation, which includes the gradient descent Weight algorithm and bias items, to learn the parameters of MLPNN. The number of hidden layer nodes was 10, the maximum number of training iterations was set to 100, the maximum mean square deviation of training results was set to 0.00004, the learning rate was set to 0.1, and the maximum number of failures was set to 18.0. Peak power output and sEMG parameters of all the subjects were subdivided into four training segments and one validation segment. This process resulted in a set of 4 × 1 training vectors and validation vectors for each subject and each test condition. Finally, the actual value (AV) and estimated value (EV) of the peak power output in the training-prediction process of five groups were compared to evaluate the performance of MLPNN.

Time-dependent power output and power loss prediction

The sEMG variables (individually and in combination) were used to estimate the power loss, and the relationship between sEMG variables and peak power output of all the subjects was mapped by the artificial neural network or linear regressions. The performance of different approaches was quantified by the signal-to-noise ratio (SNR) for the outputs2,15,31,32,51.

Statistical analysis

The results of torque in the IPT test, and the number of repetitions, work, time, and distance in the IME test were compared using analysis of variance (ANOVA) and multiple comparisons. The power outputs (W) of the first five repetitions and last five repetitions were compared using paired-samples t-test. The association between changes in the percentage of power output and changes in the percentage of sEMG-based parameters, and the relationship between the estimated changes and actual changes in power output of MLPNN were determined by Pearson’s correlation coefficients (r) and multiple linear regression. The differences of slope and intercept from two linear regressions were determined by F-test or equivalent t-test. P-values less than 0.05 were considered statistically significant (two-tailed).

Ethics approval

The study was approved by the medical ethics committee of Jilin University and was performed in accordance with relevant guidelines and regulations of the institutional review board after each subject had given written informed consent, and all procedures performed in studies involving human participants were in accordance with the Declaration of Helsinki.

Consent to participate

Each participant provided informed written consent prior to participation.

Consent for publication

Additional informed consent was obtained from all individual participants for whom identifying information is included in this article.

Results

The results of IPT and IME tests for plantar flexors and knee and hip extensors

The IPT test was first performed to determine the appropriate resistance level for the IME test (i.e., 50% IPT). The results of torque for the plantar flexors and knee and hip extensors were 154.90 ± 25.17 N∙m, 166.45 ± 27.53 N∙m, and 198.56 ± 24.53 N∙m in the IPT test, respectively. Distinct increments were evident in the three muscle groups (P < 0.05) (Fig. 2a). Furthermore, the values of CV were all less than 10%, and they were 5.13 ± 3.10%, 5.11 ± 2.63%, and 4.46 ± 3.21% for the plantar flexors and knee and hip extensors, respectively.

Figure 2
figure 2

The result of IPT and IME test for plantar flexors and knee and hip extensors. Note: IPT isometric peak torque, IME isotonic muscular endurance. PFs plantar flexors, KEs knee extensors, HEs hip extensors. The comparison between PFs and KEs, PFs and HEs, or the power output of the first 5 repetitions and last 5 repetitions, * is p < 0.05, * * is p < 0.01; the comparison between KEs and HEs, # is p < 0.05, ## is p < 0.01.

Full size image

The values of work, distance, and time in the IME test from low to high were the knee extensors (1407.28 ± 456.93 J, 1582.90 ± 635.88°, and 35.20 ± 8.77 s), plantar flexors (2259.56 ± 771.88 J, 2431.07 ± 1088.14°, and 58.65 ± 25.43 s), and hip extensors (6460.69 ± 2521.18 J, 6550.79 ± 2421.75°, and 59.10 ± 18.13 s). Distinct increments were evident in these muscle groups for the work and distance (P < 0.01) (Fig. 2b–d). The number of repetitions in the IME test from low to high were the knee extensors (31.48 ± 9.52), hip extensors (48.42 ± 16.51), and plantar flexors (51.84 ± 13.30). Regarding the number of repetitions and time in the IME test, the results of the hip extensors and plantar flexors were significantly higher than the results of the knee extensors (P < 0.01) (Fig. 2d, e).

Two subjects repeated ankle plantar flexion more than 69 times, four subjects repeated knee extension more than 40 times, and six subjects repeated hip extension more than 65 times (Fig. 2g–i). Except for these more powerful subjects, the power output measured from all other subjects decreased continuously with the number of repetitions for plantar flexors and knee and hip extensors. The power output had a significant difference between the first five repetitions and the last five repetitions for plantar flexors (629.62 ± 13.27 W vs. 388.73 ± 15.96 W), knee extensors (606.21 ± 30.20 W vs. 377.47 ± 15.30 W), and hip extensors (2036.58 ± 180.96 W vs. 1227.73 ± 186.19 W) (P < 0.01) (Fig. 2f).

The association between changes in percentage of power output and changes in percentage of sEMG-based parameters

As shown in Table 1 and Fig. 3, the changes of power output were inversely correlated with amplitude-based parameters, the correlations were significant in most muscle groups (r = 0.077–0.215, P < 0.05), and RMS percentage (RMS%) had a higher correlation coefficient than MAV percentage (MAV%). Also, the changes of power output were positively correlated with spectral parameters, the correlations were significant in most muscle groups (r = 0.078–0.301, P < 0.05), and MDF percentage (MDF%) had a higher correlation coefficient than MNF percentage (MNF%). Moreover, the changes of power output were also positively correlated with instantaneous frequency, the correlations were significant in all muscle groups (r = 0.121–0.443, P < 0.01), and IMDF percentage (IMDF%) had a higher correlation coefficient than IMNF percentage (IMNF%). Furthermore, all of the correlation coefficients and most of the SNRs of instantaneous frequency (SNR = 4.811–8.341) were higher than amplitude-based parameters (SNR = 4.438–7.763) and spectral parameters (SNR = 3.971–7.878).

Table 1 Percent changes of linear time–frequency parameters against percent changes of peak power output and signal-to-noise ratio.
Full size table
Figure 3
figure 3

The association between changes in percentage of power output and changes in percentage of instantaneous frequency parameters (percentage of the first two repetitions). Note: IMNF instantaneous mean frequency, IMDF instantaneous median frequency. MG medial gastrocnemius, LG lateral gastrocnemius, VM vastus medialis, RF rectus femoris, VL,vastus lateralis, GM gluteus maximus, BF biceps femoris.

Full size image

The difference between linear regression and non-linear neural network for predicting the power loss

The square of Pearson’s correlation coefficient (r) was equal to the coefficient of determination (R2) of univariate linear regression, where R2 reflects the percentage of total variation of a dependent variable that can be explained by the regression relationship of an independent variable. Thus, RMS%, MAV%, MNF%, MDF%, IMNF%, and IMDF% as single parameter predictors accounted for 1.02–4.62%, 0.59–2.79%, 0.61–5.95%, 1.02–9.06%, 1.46–15.92%, and 1.49–19.62% of the performance variance of changes in power output, respectively (Table 1 and Fig. 3). Stepwise multiple linear regression showed that the combination of sEMG-based parameters provided more accurate power mapping in a linear mapping than a single sEMG-based parameter predictor and accounted for 5.52–23.72% of the performance variance of changes in power output (Table 2). Moreover, the non-linear neural network based on the combination of sEMG-based parameters also provided higher correlation coefficients and SNR values (r = 0.231–0.491; SNR = 6.692–11.652) compared to multiple linear regression (r = 0.218–0.475; SNR = 5.555–8.590). Furthermore, the comparison between the regression lines of actual versus estimated changes in power output for both techniques indicated statistical significance (P < 0.01) (Table 2 and Fig. 4).

Table 2 The difference between linear regression and non-linear neural network for predicting the power loss.
Full size table
Figure 4
figure 4

Actual changes versus estimated changes in peak power output obtained from both linear and non-linear models. Note: r pearson's correlation coefficients, R2 coefficient of determination. NN neural network, MR multiple regression. MG medial gastrocnemius, LG lateral gastrocnemius, VM vastus medialis, RF rectus femoris, VL vastus lateralis, GM gluteus maximus, BF biceps femoris.

Full size image

Discussion

Losses of force, torque, and power output are typically used as direct mechanical variables to measure muscle fatigue11,12,13,14. Historically, muscle fatigue has been defined as the inability to maintain the required or expected force in isometric testing protocols. This determination of muscular endurance emphasizes the maximum force capacity and assumes strong muscles are also more powerful muscles2,3,52. In the present study, IPT was measured first to determine the appropriate resistance level for the IME test. As a larger muscle has a stronger force-generating capability with a greater physiologic cross-sectional area22,23,53, IPT exhibited a distinct increment in the plantar flexors, knee extensors, and hip extensors. However, isometric testing can only test the ability of the neuromuscular system to generate force or torque rapidly, and it does not determine muscular power, as its stationary nature prevents any assessment of velocity53,54. Therefore, the dynamic assessment of fatigue is not interchangeable with the isometric assessment of fatigue52, and optimal performance of dynamic contractions requires not only muscle force production but also a velocity component2,24. The order of IME differed from the order of IPT for the three tested muscle groups, showing that the ability to sustain maximal power output has a different physiological basis than muscle strength52. Specifically, knee extensors had the weakest endurance, with moderate torque output and minimum repetitions, plantar flexors had moderate endurance with minimum torque output and maximum repetitions, and hip extensors had the most powerful endurance with maximum torque output and moderate repetitions. Muscles must be activated quickly to produce maximal power, and the rapid force also correlates with the function of both neural activation and muscle contraction velocities2,3,52. Thus, the torque–velocity (T–V) and power–velocity (P–V) relationships are frequently used to evaluate the contractile and functional consequences of muscle fatigue52,53,55.

Muscular power is generated and can be measured during dynamic contractions associated with an applied force, regardless of speed55,56. However, muscles must be activated quickly to produce maximal power, and maximal power development usually occurs at velocities where force is moderate3,24,55. Indeed, maximal power output occurred at the point representing one-half of the projected maximal velocity and one-half of the projected maximal torque3,24,55. Thus, 50% IPT was the acceptable highest resistance for subjects to produce the maximal power output during each contraction in the fatigue protocol of the IME test3,14,57, and muscle fatigue was defined as a time-dependent loss in maximal power output. Different from fatigue protocols used by previous studies15,30,31,32,33,58, the duration or number of repetitive contractions of the IME protocol in the present study was the total output until the subject could not carry on and voluntarily gave up. The limit of a subject’s endurance during the IME test, that is, the point at which the subject is unwilling or unable to continue repetitive contractions, has been referred to as the point of ‘exhaustion’, ‘the limit of tolerance’, or the point of ‘fatigue’4,5. I n this study, two of the same mechanical manifestations of muscle fatigue found in previous studies were observed: one was a significant difference in power output between the first five repetitions and the last five repetitions, and the other was a progressive decrease of power output as the number of repetitions increased1,14,39,59. T herefore, by keeping all of the variables consistent except for time, muscular endurance can be measured by considering the amount of work produced or the activity duration via the recommended IME testing protocol in this study.

The electrical activity of muscle fibers can be characterized by sEMG and used to indirectly assess muscle fatigue caused by the prolongation of muscle contractions over time17,60. Traditional parameters such as amplitude-based parameters or spectral parameters based on FT may be questionable for mapping muscle fatigue due to the non-stationarity of the sEMG signal during dynamic contractions12,13,30,46. Similar to previous studies28,30,45, the results of this study also showed that the use of traditional time-domain indices or spectrum indices alone were not sensitive enough to determine muscle fatigue due to their poor association with power output, and these indices as single parameter predictors accounted for a low percentage of the performance variance of changes in power output. Studies addressing the non-stationarity of the sEMG signal confirmed that the CWT had the best accuracy and estimation capacity on a simulated data test and better accuracy for mapping changes in sEMG signals recorded during dynamic contractions when compared with other time–frequency distributions, and the indices of fatigue based on the CWT were instantaneous frequency parameters12,13,32. Using the CWT, which enables variable window sizes in analyzing different frequency components within a signal, a shift toward lower frequencies and, thus, a decrease in the IMNF and IMDF over the fatiguing dynamic contractions were observed32. Practically, these two indices provided greater accuracy to map losses in power output than the traditional sEMG-based parameters. In addition, some common behavior was identified, such as that the RMS was more sensitive than MAV, MDF was more sensitive than MNF17,46,51, and IMDF was preferable to IMNF as it had higher sensitivity and lower estimation error17,51,61,62.

For linear versus non-linear mapping of power loss during dynamic fatiguing contractions, some studies showed that a non-linear model based on a learning procedure provided more accurate tracking of fatigue using sEMG variables during isometric, isokinetic, and random elbow contractions12,34. However, another study showed that the linear and non-linear approaches were equally valid to estimate changes in power loss during a fatiguing repetitive leg extension exercise12,31. In the present study, non-linear techniques were developed using an MLPNN to combine different time and spectral features of the sEMG signal into a fatigue index representing the estimated changes in power output12,31,34,35. The results showed that the estimation errors were smaller when using non-linear mapping of power loss during dynamic contractions compared to linear mapping, as it showed higher SNR and correlation coefficients between the actual and estimated power output in three muscle groups of lower limbs. Therefore, non-linear mapping is a more powerful approach for training the network with data from all subjects, and using just one neural network can provide a more general technique to track changes in power loss for different subjects12,15,51. Differences in accuracy may be associated with different fatigue protocols, muscle groups, and muscle actions, but these differences remain unclear and of potential interest for further studies. Furthermore, it should be noted that non-linear techniques provided more accurate mapping of power loss but required more computational time.

Isotonic and isokinetic movements are two dynamic methods used to assess muscle power and improve muscle strength, and their respective superiority has been demonstrated27,57. Isokinetic testing controls the angular velocity and allows the force or torque to vary as muscle output changes, and it tends to “accommodate” the patient’s effort and is mainly used to measure the muscular power under constant velocity during rehabilitation28,53,63. Isotonic testing is considered to be more relevant to normal voluntary contractions, as the load is held constant but the velocity can vary27,28. Thus, the isotonic testing protocol and corresponding database presented herein should have wide application in the evaluation of sports science, rehabilitation medicine, and human-factor engineering. For instance, it is more important to maximize the neural drive than to increase absolute force levels during the early stages of rehabilitation, so clinicians have been recommended to incorporate early isotonic training and evaluation, as those contractions resulted in greater motor unit activation per unit of work performed2,57. In addition, the isotonic testing protocol is beneficial for developing and evaluating training programs that effectively enhance maximal power production, since sports activities involve the acceleration and deceleration of the lower extremities22,23. Moreover, dynamic contractions are more closely related to day-to-day activities and are psychologically more demanding since they require both movement and postural control36. The debilitating effects of increased physiological strain on endurance performance are accompanied by debilitating effects of increased perceived fatigability19,20. When evaluating physical ability or functionality related to work activities, an IME test might offer more convincing and accurate results that provide further insights into the relationships between human performance and muscle endurance required in real-world activities19,40.

To develop electrophysiological evaluation methods of muscle fatigue in IME tests, linear mapping alone and a combination of sEMG variables with non-linear mapping of power loss were compared, indicating that the non-linear techniques (e.g., MLPNN) might have an advantage in analyzing non-linear dynamic systems (e.g., the IME testing protocol). Practically, the linear technique may be preferable for mapping power changes based on sEMG variables due to the lower computational time required by the linear approach12,17,60. Fatiguability was examined by assessing the subject’s endurance time until they experienced fatigue and decided to stop, and the protocol may better fit the views in which they considered fatigue as a safety mechanism aimed at preventing overuse injuries in previous studies6,7,9. However, there may be different mechanisms behind fatigue development and exhaustion in the IME testing protocol compared with previous dynamic fatiguing protocols using fixed sets, repetitions, and rest times15,30,31,32,33,39. This may partially explain the low correlations between power loss and the sEMG-based parameters, but further research is needed. Moreover, the sensitivity of other proposed fatigue indices, such as Dimitrov’s spectral fatigue index (Finsmk), wavelet spectral parameters, the ratios of EMG power content in the high- and low-frequency ranges (Fihlrx), and other non-linear parameters12,16,17,51,64, was not investigated. Further studies can be conducted to determine more effective electrophysiological evaluation methods of neuromuscular function while considering the parameters in the IME testing protocol.

Conclusion

Muscular endurance required in real-world activities can be determined by measuring the amount of work produced or the activity duration via the recommended IME testing protocol under a psychophysiological termination criterion. Furthermore, non-linear mapping techniques provide more powerful mapping of power loss compared to linear mapping techniques for the IME testing protocol.

Data availability

The datasets used and/or analyzed during the current study are available from the corresponding author on reasonable request.