Protocol | Published:

Surface-wetting characterization using contact-angle measurements

Nature Protocolsvolume 13pages15211538 (2018) | Download Citation


Wetting, the process of water interacting with a surface, is critical in our everyday lives and in many biological and technological systems. The contact angle is the angle at the interface where water, air and solid meet, and its value is a measure of how likely the surface is to be wetted by the water. Low contact-angle values demonstrate a tendency of the water to spread and adhere to the surface, whereas high contact-angle values show the surface’s tendency to repel water. The most common method for surface-wetting characterization is sessile-drop goniometry, due to its simplicity. The method determines the contact angle from the shape of the droplet and can be applied to a wide variety of materials, from biological surfaces to polymers, metals, ceramics, minerals and so on. The apparent simplicity of the method is misleading, however, and obtaining meaningful results requires minimization of random and systematic errors. This article provides a protocol for performing reliable and reproducible measurements of the advancing contact angle (ACA) and the receding contact angle (RCA) by slowly increasing and reducing the volume of a probe drop, respectively. One pair of  ACA and RCA measurements takes ~15–20 min to complete, whereas the whole protocol with repeat measurements may take ~1–2 h. This protocol focuses on using water as a probe liquid, and advice is given on how it can be modified for the use of other probe liquids.

Access optionsAccess options

Rent or Buy article

Get time limited or full article access on ReadCube.

from $8.99

All prices are NET prices.

Additional information

Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Reliable measurement of the receding contact angle:

Guidelines to measurements of reproducible contact angles using a sessile-drop technique:

Characterization of super liquid-repellent surfaces:


  1. 1.

    Riederer, M. & Schreiber, L. Protecting against water loss: analysis of the barrier properties of plant cuticles. J. Exp. Bot. 52, 2023–2032 (2001).

  2. 2.

    Gao, X. & Jiang, L. Water-repellent legs of water striders. Nature 432, 36 (2004).

  3. 3.

    Barthlott, W. & Neinhuis, C. Purity of the sacred lotus, or escape from contamination in biological surfaces. Planta 202, 1–8 (1997).

  4. 4.

    Parker, A. R. & Lawrence, C. R. Water capture by a desert beetle. Nature 414, 33–34 (2001).

  5. 5.

    Zhao, G. et al. High surface energy enhances cell response to titanium substrate microstructure. J. Biomed. Mater. Res. Part A 74, 49–58 (2005).

  6. 6.

    Pankaj, S. K. et al. Applications of cold plasma technology in food packaging. Trends Food Sci. Technol. 35, 5–17 (2014).

  7. 7.

    Tian, D., Song, Y. & Jiang, L. Patterning of controllable surface wettability for printing techniques. Chem. Soc. Rev. 42, 5184–5209 (2013).

  8. 8.

    Korhonen, J. T., Kettunen, M., Ras, R. H. A. & Ikkala, O. Hydrophobic nanocellulose aerogels as floating, sustainable, reusable, and recyclable oil absorbents. ACS Appl. Mater. Interfaces 3, 1813–1816 (2011).

  9. 9.

    Young, T. An essay on the cohesion of fluids. Philos. Trans. R. Soc. Lond. 95, 65–87 (1805).

  10. 10.

    Extrand, C. W. & Kumagai, Y. An experimental study of contact angle hysteresis. J. Colloid Interface Sci. 191, 378–383 (1997).

  11. 11.

    Marmur, A. Solid surface characterization by wetting. Annu. Rev. Mater. Res. 39, 473–489 (2009).

  12. 12.

    Marmur, A. A guide to the equilibrium contact angles maze in Contact Angle, Wettability and Adhesion Vol. 6 3–18 (ed. Mittal K. L.) (CRC Press, 2009).

  13. 13.

    Quéré, D. Wetting and roughness. Annu. Rev. Mater. Res. 38, 71–99 (2008).

  14. 14.

    Andrieu, C., Sykes, C. & Brochard, F. Average spreading parameter on heterogeneous surfaces. Langmuir 104, 2077–2080 (1994).

  15. 15.

    de Gennes, P. G. Wetting: statics and dynamics. Rev. Mod. Phys. 57, 827–863 (1985).

  16. 16.

    Blake, T. D. The physics of moving wetting lines. J. Colloid Interface Sci. 299, 1–13 (2006).

  17. 17.

    Drelich, J. Guidelines to measurements of reproducible contact angles using a sessile-drop technique. Surf. Innov. 1, 248–254 (2013).

  18. 18.

    Good, R. J. Contact angle, wetting, and adhesion: a critical review. J. Adhes. Sci. Technol. 6, 1269–1302 (1992).

  19. 19.

    Kwok, D. Y. & Neumann, A. W. Contact angle measurement and contact angle interpretation. Adv. Colloid Interface Sci. 81, 167–249 (1999).

  20. 20.

    Lam, C. N. C., Lu, J. J. & Neumann, A. W. Measuring contact angle. in Handbook of Applied Surface and Colloid Chemistry (ed. K. Holmberg) Vol. 2 251–277 (2002).

  21. 21.

    Della Volpe, C. & Siboni, S. The Wilhelmy method : a critical and practical review. Surf. Innov. 6, 120–132 (2018).

  22. 22.

    Liimatainen, V. et al. Mapping microscale wetting variations on biological and synthetic water-repellent surfaces. Nat. Commun. 8, 1798 (2017).

  23. 23.

    Pierce, E., Carmona, F. J. & Amirfazli, A. Understanding of sliding and contact angle results in tilted plate experiments. Colloids Surf. A Physicochem. Eng. Asp. 323, 73–82 (2008).

  24. 24.

    Krasovitski, B. & Marmur, A. Drops down the hill: theoretical study of limiting contact angles and the hysteresis range on a tilted plate. Langmuir 21, 3881–3885 (2005).

  25. 25.

    Rudawska, A. & Jacniacka, E. Analysis for determining surface free energy uncertainty by the Owen-Wendt method. Int. J. Adhes. Adhes. 24, 451–457 (2009).

  26. 26.

    Zhao, Q., Liu, Y. & Abel, E. W. Effect of temperature on the surface free energy of amorphous carbon films. J. Colloid Interface Sci. 280, 174–183 (2004).

  27. 27.

    Hoorfar, M. & Neumann, A. W. Recent progress in axisymmetric drop shape analysis (ADSA). Adv. Colloid Interface Sci. 121, 25–49 (2006).

  28. 28.

    Tavana, H. & Neumann, A. W. On the question of rate-dependence of contact angles. Colloids Surf. A Physicochem. Eng. Asp. 282–283, 256–262 (2006).

  29. 29.

    Korhonen, J. T., Huhtamäki, T., Ikkala, O. & Ras, R. H. A. Reliable measurement of the receding contact angle. Langmuir 29, 3858–3863 (2013).

  30. 30.

    Grundke, K. et al. Experimental studies of contact angle hysteresis phenomena on polymer surfaces - toward the understanding and control of wettability for different applications. Adv. Colloid Interface Sci. 222, 350–376 (2015).

Download references


The protocol is the result of a procedure gradually developed since wetting research was begun in the R.H.A.R. group, and we acknowledge the contributions of H. Mertaniemi, T. Verho and M. Latikka. This work was supported by the European Research Council ERC-2016-CoG (725513-SuperRepel) and the Academy of Finland (Centres of Excellence Programme 2014–2019). X.T. is grateful for the support of the One Hundred Talents Program of SYSU and the One Thousand Youth Talents Program of China.

Author information

Author notes

    • Juuso T. Korhonen

    Present address: Department of Neuroscience and Biomedical Engineering, School of Science, Aalto University, Espoo, Finland


  1. Department of Applied Physics, School of Science, Aalto University, Espoo, Finland

    • Tommi Huhtamäki
    • , Xuelin Tian
    • , Juuso T. Korhonen
    •  & Robin H. A. Ras
  2. School of Materials Science and Engineering, Sun Yat-sen University, Guangzhou, China

    • Xuelin Tian
  3. Department of Bioproducts and Biosystems, School of Chemical Engineering, Aalto University, Espoo, Finland

    • Robin H. A. Ras


  1. Search for Tommi Huhtamäki in:

  2. Search for Xuelin Tian in:

  3. Search for Juuso T. Korhonen in:

  4. Search for Robin H. A. Ras in:


R.H.A.R. coordinated the project. T.H., X.T. and J.T.K. performed the experiments. All authors participated in designing the protocol. T.H. and R.H.A.R. wrote the manuscript with contributions from all authors. J.T.K. wrote the Python code.

Competing interests

The authors declare no competing interests.

Corresponding author

Correspondence to Robin H. A. Ras.

Supplementary information

  1. Supplementary Methods: Python code for solving the Young–Laplace equation.

    The minimum advancing drop volumes (= the recommended starting volume for the receding contact-angle measurement) needed to reach RCA at 10 µL (Fig. 6), were obtained by solving the Young–Laplace equation by numerical integration, using Python programming language with Scipy library. The shape and size of the drop for different pairs of contact angle and drop volume were solved using a code that is provided in this supplementary file

About this article

Publication history




By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.