Skip to main content

Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Quantum non-demolition readout of an electron spin in silicon

Abstract

While single-shot detection of silicon spin qubits is now a laboratory routine, the need for quantum error correction in a large-scale quantum computing device demands a quantum non-demolition (QND) implementation. Unlike conventional counterparts, the QND spin readout imposes minimal disturbance to the probed spin polarization and can therefore be repeated to extinguish measurement errors. Here, we show that an electron spin qubit in silicon can be measured in a highly non-demolition manner by probing another electron spin in a neighboring dot Ising-coupled to the qubit spin. The high non-demolition fidelity (99% on average) enables over 20 readout repetitions of a single spin state, yielding an overall average measurement fidelity of up to 95% within 1.2 ms. We further demonstrate that our repetitive QND readout protocol can realize heralded high-fidelity (>99.6%) ground-state preparation. Our QND-based measurement and preparation, mediated by a second qubit of the same kind, will allow for a wide class of quantum information protocols with electron spins in silicon without compromising the architectural homogeneity.

Introduction

Single electron spins confined in silicon quantum dots hold great promise as a quantum computing architecture with demonstrations of long coherence times1, high-fidelity quantum logic gates2,3,4, basic quantum algorithms5, and device scalability6. However, the ability to measure a qubit in a single-shot QND manner has been lacking, despite its pivotal role in quantum error correction and quantum information processing, as well as its centrality to quantum science7,8,9. An ideal single-shot QND readout process would, in addition to yielding an eigenvalue of the observable with projection probability for the input state (measurement), leave the system in the projected input state (non-demolition), meaning that the measurement is repeatable and that a posterior state can be predicted based on the eigenvalue obtained (preparation)7. These features contrast with conventional readout schemes of a silicon spin qubit, which inherently demolish the spin state by mapping it to a more readily detectable, charge degree of freedom1,2,3,4,5,6,10. Such spin-to-charge conversion techniques are employed to facilitate to measure the small magnetic moment of a single electron spin within its relaxation time, which, although exceptionally long for a solid-state quantum system, is limited to the millisecond timescale. A QND readout requires a mechanism to exquisitely expose the system to external circuitry for readout while maintaining the coherence and integrity of the qubit. Synthesizing an ancilla system which can be repeatedly initialized, controlled conditionally on the qubit state and separately measured, all on the microsecond timescale, constitutes a major challenge for the QND readout of a silicon electron spin qubit.

In this work we demonstrate repeatable measurements of a silicon electron spin qubit. We use a neighboring electron spin as an ancilla, with which we can perform a QND qubit readout at a 60 μs repetition cycle through a conditional rotation and spin-selective tunneling. The highly QND nature is evidenced by the strong correlation between successive ancilla measurement outcomes. We take advantage of the repeatability and construct a QND qubit readout from n consecutive ancilla measurements to improve the overall performance. For complete characterization as a QND readout process, we identify and evaluate three key metrics7: the non-demolition fidelity (FQND = 99% for n = 1); the measurement fidelity (FM = 95% for n = 20); the preparation fidelity (FP = 92% for n = 20). (The numbers are the average of the spin-down and -up cases.) The non-demolition and preparation fidelities (FQND and FP) which are dissimilar to those in the destructive readout illustrate the distinct properties of the QND readout. We further show that the repetitive readout scheme allows us to preselect the cases where the qubit state is prepared with fidelities >99.6%.

Results

Ising-coupled qubit-ancilla system

Our qubit and ancilla are electron spins confined in a double Si/SiGe quantum dot (Fig. 1a) with natural isotopic abundance11. Spin states can be discriminated and reinitialized within 30 μs relying on energy-selective spin-to-charge conversion10,12 and the reflectometry response from a neighboring charge sensor (see Methods for details). An on-chip micromagnet magnetized in an external magnetic field Bext = 0.51 T separates the resonance frequencies of the qubit and ancilla spins by 640 MHz (centered around ~16.3 GHz). This enables frequency-selective electric-dipole-spin resonance rotations of individual spins at several MHz and ensures that the exchange interaction of ~MHz is well represented by the Ising type with minimal disturbance to the spin polarizations13,14.

Fig. 1: Qubit and ancilla system.
figure1

a Schematic of a device. The qubit spin (blue) and the ancilla spin (red) are hosted in two singly-occupied dots in a silicon quantum well layer. A proximal single electron transistor serves as a charge sensor. Scale bar: 200 nm. b Control pulse. Two microwave tones (represented by different colors) are used to selectively rotate qubit and ancilla spins. A controlled-phase shift is induced by applying square pulses simultaneously to VT, VB as well as to VC. c Ancilla spin-up probability after an entangling gate pulse. Traces with and without a π pulse applied to the qubit spin are plotted with filled and open symbols, respectively. d Measured controlled-phase accumulation. The dotted line indicates tCZ = 0.53 μs used for a conditional rotation.

We correlate the ancilla and the qubit spins by a controlled-rotation gate (Fig. 1b). During a square gate-voltage pulse for a duration tCZ at a symmetric operation point, the ancilla spin acquires a qubit-state-dependent phase due to enhanced exchange coupling3,15. A Hahn echo sequence converts this phase to the ancilla spin polarization, in a robust manner against a slow drift of the ancilla precession frequency and the qubit-state-independent phase induced by the square gate-voltage pulse (~20π per μs) and the microwave bursts (~0.16π)16,17. We extract the qubit-dependent phase shift by changing the prepared qubit state by the microwave burst time tb (Fig. 1c). The extracted phase grows linearly with tCZ (Fig. 1d), consistent with an induced excess exchange coupling J of 0.94 MHz. Choosing tCZ = 0.53 μs (=1/2J) and an appropriate projection phase θ, we can implement a conditional rotation which maps the qubit state to the ancilla spin, allowing for the ancilla-based measurement of the qubit spin.

Demonstration of repetitive readout

We now demonstrate that the ancilla can be repeatedly entangled with the qubit and measured, using a sequence shown in Fig. 2a. After preparing the qubit state by microwave control, we repeat 30 cycles of a controlled-rotation gate and the ancilla measurement and reinitialization, until we destructively read out and reinitialize the qubit. We use mi and q to denote the outcomes of the i-th ancilla measurement (with i = 1, 2, … 30) and the final qubit readout, respectively. Remarkably, all ancilla measurement outcomes show clear Rabi oscillations (Fig. 2b), indicating each functions as a single-shot QND readout of the qubit. Strong correlations between successive measurements, a hallmark of the QND readout, are verified from joint probabilities P(m1m2), see Fig. 2c.

Fig. 2: Repetitive readout.
figure2

a Quantum circuit for repetitive measurements. b Spin-up probabilities of the i-th ancilla measurement (only i = 1, 5, 10, 20, and 30 are shown for brevity) and the final qubit readout (q) out of 1000 events. Note the oscillation visibility for q is influenced by the compromised sensor sensitivity. c Probabilities of the four joint outcomes for the first and second ancilla measurements. The triangle symbols represent the experimental data, and the solid lines are the fit results to the model which takes into account preparation and measurement imperfections.

The Rabi oscillation visibility of mi is affected by both the probability distribution \(p_{i - 1}^{ \downarrow \left( \uparrow \right)}\) of the prepared qubit spin state si−1 and the i-th QND measurement fidelity \(f_i^{ \downarrow \left( \uparrow \right)}\) given \(s_{i - 1} = \downarrow ( \uparrow )\). We separate the error in the prepared qubit spin state (during the process of initialization, rotation, and preceding ancilla measurements) from the measurement infidelity18 by expressing the joint probability P(mim30) as

$$P\left( {m_im_{30}} \right) = \mathop {\sum }\limits_{s = \downarrow , \uparrow } p_{i - 1}^s{\mathrm{\Theta }}_{s,m_i}\left(\, {f_i^s} \right){\mathrm{\Theta }}_{s,m_{30}}\left( {g_i^s} \right).$$
(1)

Here \(g_i^{ \downarrow \left( \uparrow \right)}\) denotes the measurement fidelity of m30 for si−1 prepared in ↓(↑), and \(\Theta _{s,m}\left( f \right)\) equals f when s = m and 1 − f when s ≠ m. We model \(p_{i - 1}^{ \downarrow ( \uparrow )}\) by an exponentially decaying Rabi oscillation11 and obtain \(p_i^{ \downarrow \left( \uparrow \right)}\), \(f_i^{ \downarrow \left( \uparrow \right)}\), and \(g_i^{ \downarrow \left( \uparrow \right)}\) as a function of i (see Methods and Supplementary Fig. 2). We find that \(f_i^{ \downarrow ( \uparrow )}\) is essentially i-independent as expected, with the average 85% (75%) for i = 1–20.

Characterization of the QND readout

A distinct feature of the QND readout is that it is repeatable, meaning we can potentially gain more accurate information about the qubit state from consecutive measurements. In the following, we leverage this potential by constructing a cumulative QND readout from n outcomes, mn = {m1, m2,… mn} which yields estimators σ for s0 (the input qubit state, projected to either spin-down or -up) and ς for sn (the posterior qubit state), see Fig. 3a. We characterize its performance as a QND readout as a function of n, through three key fidelity figures of merit, FQND, FM, and FP. These fidelities are, as depicted in Fig. 3a, defined by the correspondences between the estimators (σ and ς) and/or the qubit states before and after the process (s0 and sn). Importantly, these together will enable us to test all key criteria that the QND readout should satisfy7—i.e., non-demolition (FQND), measurement (FM), and preparation (FP).

Fig. 3: Cumulative QND readout and fidelities.
figure3

a Diagram for the cumulative readout protocol and fidelity definitions. We regard n consecutive ancilla measurements (with outcomes m1, m2mn) as a single QND readout (with estimators σ and ς). The projected input spin state s0 (either ↓ or ↑) changes to the posterior state sn after the process. The ideal QND measurement would give sn, identical to s0 (non-demolition); σ, identical to s0 (measurement); and sn, identical to ς (preparation). FQND, FM, and FP quantify these properties. b \(F_{{\mathrm{QND}}}^ \downarrow\), \(F_{{\mathrm{QND}}}^ \uparrow\), and \(( {F_{{\mathrm{QND}}}^ \downarrow + F_{{\mathrm{QND}}}^ \uparrow } )/2\) after n repetitive measurements. The solid lines show the values expected from the extracted \(T_1^{ \downarrow ( \uparrow )}\). c Rabi oscillations of the qubit spin acquired from multiple ancilla measurements. Plotted with a dashed curve is the estimated true qubit spin-up probability, \(p_0^ \uparrow\), consistent with a Rabi oscillation at a 630 kHz frequency detuning. d \(F_{\mathrm{M}}^ \downarrow\), \(F_{\mathrm{M}}^ \uparrow\), and \(F_{\mathrm{M}}^{{\mathrm{avg}}} = ( {F_{\mathrm{M}}^ \downarrow + F_{\mathrm{M}}^ \uparrow } )/2\) as a function of n. State-dependent single-shot measurement fidelities \((f_i^ \downarrow > f_i^ \uparrow )\) produce even-odd effects of \(F_{\mathrm{M}}^{ \downarrow \left( \uparrow \right)}\), whereas the average \(F_{\mathrm{M}}^{{\mathrm{avg}}}\) increases monotonically. Note that \(F_{\mathrm{M}}^{{\mathrm{avg}}}\) can be related to the measurement visibility12 V through \(V = 2F_{\mathrm{M}}^{{\mathrm{avg}}} - 1\). e \(F_{\mathrm{P}}^ \downarrow\), \(F_{\mathrm{P}}^ \uparrow\), and \(( {F_{\mathrm{P}}^ \downarrow + F_{\mathrm{P}}^ \uparrow } )/2\) as a function of n.

We first assess the non-demolition fidelity \(F_{{\mathrm{QND}}}^{ \downarrow \left( \uparrow \right)}\), which addresses the requirement that the measured observable (spin-down or up) should not be disturbed. It represents the correlation between the projected input (s0) and posterior (sn) qubit states, and unlike the other two fidelities, it is expected to decrease as n is increased. \(F_{{\mathrm{QND}}}^{ \downarrow \left( \uparrow \right)}\) can be defined using the conditional probability of sn given s0 as \(F_{{\mathrm{QND}}}^{ \downarrow ( \uparrow )} = P(s_n = s_0|s_0 = \downarrow ( \uparrow ))\). It follows from this definition that \(p_n^ \downarrow = F_{{\mathrm{QND}}}^ \downarrow\; p_0^ \downarrow + ( {1 - F_{{\mathrm{QND}}}^ \uparrow } )p_0^ \uparrow\). The results obtained from the fit to this equation is shown in Fig. 3b, where \(F_{{\mathrm{QND}}}^{ \downarrow ( \uparrow )}\) gradually decreases to 99% (61%) as n is increased up to 20. By modeling the n dependence of \(p_n^ \downarrow\) (see Methods), we estimate \(F_{{\mathrm{QND}}}^{ \downarrow ( \uparrow )}\) for n = 1 to be 99.92% (97.7%), corresponding to the longitudinal spin relaxation time \(T_1^{ \downarrow ( \uparrow )}\) of 78 ms (2.5 ms) given the 60 μs cycle time.

The second requirement for the QND readout is that the measurement result should be correlated with the input state following the Born rule. We test this through the measurement fidelity defined as \(F_{\mathrm{M}}^{ \downarrow \left( \uparrow \right)} = P(\sigma = s_0|s_0 = \downarrow ( \uparrow ))\), where σ is the estimator for the input qubit state s0 based on measurement results mn. When σ is the more likely value of s0, \(P\left( {{\boldsymbol{m}}_n|s_0 = \sigma } \right) > P\left( {{\boldsymbol{m}}_n|s_0 = \bar \sigma } \right)\) with \(\bar \sigma\) denoting the spin opposite to σ. We calculate these likelihoods using a Bayes model that assumes spin-flipping events (see Methods). σ shows larger Rabi oscillations as n is increased (Fig. 3c), demonstrating \(F_{\mathrm{M}}^{ \downarrow \left( \uparrow \right)}\) enhancement by repeating ancilla measurements in our protocol. We obtain \(F_{\mathrm{M}}^{ \downarrow \left( \uparrow \right)}\) (Fig. 3d) through \(P\left( {\sigma = \downarrow } \right) = F_{\mathrm{M}}^ \downarrow p_0^ \downarrow + ( {1 - F_{\mathrm{M}}^ \uparrow } ) p_0^ \uparrow\). While \(F_{\mathrm{M}}^{ \downarrow \left( \uparrow \right)} = 88\hbox{\%}\) (73%) for n = 1, it reaches 95.6% (94.6%) for n = 20, well above the measurement fidelity threshold for the surface code8.

The last feature of the QND readout to be evaluated is the capability as a state preparation device. In order to quantify how precisely our cumulative QND readout process prepares a definite qubit state, we define the preparation fidelity FP as the conditional probability of sn = ς given the estimator ς for the posterior qubit state sn, i.e., \(F_{\mathrm{P}}^{ \downarrow \left( \uparrow \right)} = P\left( {s_n = \varsigma |\varsigma = \downarrow \left( \uparrow \right)} \right)\). We emulate the most relevant situation of a completely unknown input7 by using data with 0.08 μs < tb < 1.3 μs, for which \(p_0^ \downarrow = 0.500\). To optimally determine ς from mn, we again apply the Bayes’ rule (Methods) and compare the likelihoods \(P\left( {{\boldsymbol{m}}_n|s_n = \downarrow } \right)\) and \(P\left( {{\boldsymbol{m}}_n|s_n = \uparrow } \right)\). We estimate sn from another estimator σ′ and convert the conditional probability \(P\left( {\sigma^{ \prime} = \varsigma |\varsigma = \downarrow \left( \uparrow \right)} \right)\) to \(F_{\mathrm{P}}^{ \downarrow \left( \uparrow \right)}\) using the measurement fidelity of σ′ for sn (Methods). We obtain \(F_{\mathrm{P}}^{ \downarrow \left( \uparrow \right)} = 76\hbox{\%}\, \left( {83\hbox{\%} } \right)\) for n = 1, which increments to 95.9% (88.6%) for n = 20 (Fig. 3e).

Heralded high-fidelity state preparation

It is worth noting that for n ≥ 2, these likelihoods \(P\left( {{\boldsymbol{m}}_n|s_n = \varsigma } \right)\) can signal events where we have higher confidence in the final spin state. To explore this potential of heralded high-fidelity state preparation, we calculate the likelihood ratio \({\it{\Lambda}} ^\varsigma = P\left( {{\boldsymbol{m}}_{10}|s_{10} = \varsigma } \right)/P\left( {{\boldsymbol{m}}_{10}|s_{10} = \bar \varsigma } \right)\) (i.e., for n = 10) and select events with \({\it{\Lambda}} ^\varsigma\) above a certain threshold. The conditional probability \(P\left( {\sigma^{\prime} = \varsigma |\varsigma = \downarrow \left( \uparrow \right)} \right)\) is then estimated following the procedure described above (but with more ancilla measurements, see Methods). Indeed, \(F_{\mathrm{P}}^ \downarrow\) increases from 94 to 99% at the median (for \({\it{\Lambda}} ^ \downarrow\) > 1), and \(F_{\mathrm{P}}^ \downarrow\) reaches 99.6% at the 76th percentile, see Fig. 4. The limiting value is higher for the spin-down case, as expected from \(F_{{\mathrm{QND}}}^{ \downarrow \left( \uparrow \right)}\).

Fig. 4: Heralded enhanced preparation fidelity.
figure4

Events with high initialization confidence are selected based on \({\it{\Lambda}} ^\varsigma\). The data include 53,000 events in total and threshold percentiles with more than 5000 selected events are used for the analysis.

Discussion

In the present experiment, 30 ancilla measurements are feasible before we lose strong correlation between the input and the outcome (\(F_{{\mathrm{QND}}}^ \uparrow \;\lesssim\;\) 50%). This is limited by a relatively short electron spin lifetime, compared with single nuclear spins in silicon where 99.8% readout fidelity is achieved as a result of >99.98% non-demolition fidelity19,20. We note that, while both FM and FP are successfully improved by the cumulative QND readout, the observed FQND falls short of our earlier expectations18 and the overall QND performance is impacted by this. The ratio \(T_1^ \downarrow /T_1^ \uparrow = 31\) is deviated from the ideal thermal population ratio (=16) between the Zeeman sublevels at the electron temperature (~50 mK), and the measured \(T_1^ \uparrow\) is roughly 30 times shorter than nominal expectation for an idle spin away from the hotspot21. Indeed, data imply that the qubit relaxation occurs predominantly during the ancilla readout process (see Supplementary Fig. 1). This effect is expected to be suppressed by further quenching the residual exchange coupling (~MHz), e.g., via an interdot gate electrode6 or by fast readout with an ancilla encoded in double-dot spin states22. We anticipate that we will then improve FQND and the QND readout in all aspects, as a higher FQND should raise FM and FP that are achievable by repeating QND measurements.

FM and FP will also improve, particularly for small numbers of n, by decreasing single-shot QND measurement infidelities \(1 - f_i^{ \downarrow ( \uparrow )}\), which are 15% (25%) on average for i = 1–20. We estimate the contribution of charge discrimination error to be 1% (7%) for the spin-down (up) case (see Supplementary Fig. 3), which can be straightforwardly reduced by tuning the charge sensor sensitivity solely for the ancilla dot. The remaining single-shot infidelities (in converting the qubit spin state to an ancilla electron tunneling event) are more significant, 14% and 18% for the spin-down and -up cases, respectively. We believe that these arise from the qubit-ancilla conditional operation and the ancilla spin-to-charge conversion and initialization process, and can be addressed by optimizing the two-qubit gate operation and the spin-selective tunneling process4,10.

To conclude, we have demonstrated a QND readout of a single electron spin in silicon. The presented technique uses an electron spin in a neighboring dot as an ancilla, requiring no increased structural complexity to multiple-dot quantum information processing units. Central to the 99% non-demolition fidelity are a synthesized Ising type qubit-ancilla coupling and the rapid conditional ancilla rotation and measurement. The ancilla-based QND readout is a crucial element in qubit error detection and correction protocols. More specifically, it should be naturally extensible to QND measurements of the parity of multiple qubits with proper choice of single- and two-qubit gate operations, in contrast to the spin blockade-based single-shot readout of a single spin23, which may also allow for repetitive readout24. Combined with high-fidelity single- and two-qubit gates2,4, the demonstrated results will pave the way toward fault-tolerant quantum-information processing in the silicon quantum-dot platform.

Methods

Measurement setup

The device is a dual-gated accumulation-mode Si/SiGe quantum dot reported in ref. 11 and is measured in a dry dilution refrigerator (Oxford Instruments Triton 200). A Tektronix AWG5014 arbitrary waveform generator is used to generate three-channel gate pulses (applied to VC, VT, and VB). To ensure the adiabaticity of the pulses, they are filtered through Bessel analog filters with a 3 dB cutoff frequency at 39 MHz. The AWG5014 triggers a Tabor WX2184 waveform generator which produces I/Q modulation waveforms for two Keysight 8267D microwave sources. We use single-sideband modulation at 20 MHz to suppress the effects from leakage and spurious modes. In order to maintain the device in the symmetric condition throughout a controlled-rotation operation, the pulse heights for VC, VT, and VB are chosen to be +30.0 mV, −23.1 and −21.0 mV, respectively15. Each spin is read out using the energy-selective tunneling to the adjacent reservoir. (The ancilla and qubit electrons tunnel in and out from different reservoirs.) The reflectometry signal (at 205 MHz) is demodulated to baseband, sampled by an AlazarTech digitizer ATS9440 at 10 MSPS, filtered at 1 MHz using a second order Butterworth digital filter and decimated at 2 MSPS for post processing. The lengths of individual traces are 45 μs for experiments in Fig. 1c and 30 μs for those in Fig. 2. Peak-to-peak values (the difference between the maximum and the minimum readings in individual traces) are used to detect the tunneling events.

Bayesian models

We construct a cumulative QND readout from n consecutive outcomes (mn) of ancilla measurements (Fig. 3) based on the performance of single-shot QND measurements (mi) characterized using Eq. (1) as described in the main text. In order to analyze all joint probabilities in a consistent manner, the fitting is performed in the following steps. First, the joint probability P(mim30) for each value of i is fit to Eq. (1) with \(p_{i - 1}^ \downarrow \left( { = 1 - p_{i - 1}^ \uparrow } \right)\), \(f_i^{ \downarrow \left( \uparrow \right)}\), and \(g_i^{ \downarrow \left( \uparrow \right)}\) as fitting parameters, assuming that \(p_{i - 1}^ \downarrow\) is an exponentially decaying Rabi oscillation11, similarly to ref. 18. We then model the i-dependence of \(p_i^ \downarrow\) as \(p_{i\, +\, 1}^ \downarrow = \rho ^ \downarrow p_i^ \downarrow + \left( {1 - \rho ^ \uparrow } \right)p_i^ \uparrow\), where \(\rho ^{ \downarrow \left( \uparrow \right)} = {\mathrm{exp}}\left( { - 60\,\upmu {\mathrm{s}}/T_1^{ \downarrow \left( \uparrow \right)}} \right)\) is the spin conservation probability and \(p_0^ \downarrow\) is parametrized using an exponentially decaying Rabi oscillation again. Finally, we fix \(p_{i - 1}^ \downarrow\) to the values calculated from \(p_0^ \downarrow\) and \(\rho ^{ \downarrow ( \uparrow )}\) in the model above and fit P(mim30) for each value of i with only \(f_i^{ \downarrow \left( \uparrow \right)}\) and \(g_i^{ \downarrow \left( \uparrow \right)}\) as fitting parameters. Values extracted in these initial and later analysis steps are compared in Supplementary Fig. 2.

When we regard a cumulative QND readout process as a measurement device, it should estimate from mn the input spin state s0 to be either ↓ or ↑. Our goal is to precisely determine the estimator σ for s0 such that s0 is more likely σ given mn, i.e., \(P\left( {s_0 = \sigma |{\boldsymbol{m}}_n} \right) > P\left( {s_0 = \bar \sigma |{\boldsymbol{m}}_n} \right)\), assuming no prior knowledge about the probability distribution of P(s0), i.e., \(P\left( {s_0 = \downarrow } \right) = P\left( {s_0 = \uparrow } \right) = 1/2\). From the Bayes theorem, we see that for the more likely value of σ

$$P\left( {{\boldsymbol{m}}_n|s_0 = \sigma } \right) = \frac{{P\left( {s_0 = \sigma |{\boldsymbol{m}}_n} \right)P\left( {{\boldsymbol{m}}_n} \right)}}{{P\left( {s_0 = \sigma } \right)}}\, > \, \frac{{P\left( {s_0 = \bar \sigma |{\boldsymbol{m}}_n} \right)P\left( {{\boldsymbol{m}}_n} \right)}}{{P\left( {s_0 = \bar \sigma } \right)}} = P\left( {{\boldsymbol{m}}_n|s_0 = \bar \sigma } \right),$$
(2)

meaning that the input state estimation comes down to comparing likelihoods \(P\left( {{\boldsymbol{m}}_n|s_0 = \downarrow } \right)\) and \(P\left( {{\boldsymbol{m}}_n|s_0 = \uparrow } \right)\). For optimal performance, we should consider all (2n−1) possible spin trajectories \(\left\{ {s_1,s_2, \ldots s_{n - 1}} \right\}\) following s0, with the realization probabilities taken into account. Using the spin transition probability to calculate the realization probabilities, the likelihood P(mn|s0) can be computed as

$$P\left( {{\boldsymbol{m}}_1|s_0} \right) = {\mathrm{\Theta }}_{s_0,m_1}\left(\, {f_1^{s_0}} \right)$$
(3)

for n = 1 and for n > 1

$$P\left( {{\boldsymbol{m}}_n|s_0} \right) = \mathop {\sum }\limits_{s_1 = \downarrow }^ \uparrow \cdots \mathop {\sum }\limits_{s_{n - 1} = \downarrow }^ \uparrow {\mathrm{\Theta }}_{s_{n - 1},m_n}\left(\; {f_n^{s_{n - 1}}} \right)\mathop {\prod }\limits_{i = 1}^{n - 1} {\mathrm{\Theta }}_{s_{i - 1},s_i}\left( {\rho ^{s_{i - 1}}} \right){\mathrm{\Theta }}_{s_{i - 1},m_i}\left(\; {f_i^{s_{i - 1}}} \right).$$
(4)

When we instead view a cumulative QND readout process as a state preparation device, it prepares the posterior spin state sn in a specific state, either ↓ or ↑, as determined from mn. Our task is then to construct the estimator ς for sn such that sn is more likely ς given mn, i.e., \(P\left( {s_n = \varsigma |{\boldsymbol{m}}_n} \right) > P\left( {s_n = \bar \varsigma |{\boldsymbol{m}}_n} \right)\), assuming no prior knowledge about the probability distribution of P(sn), i.e., \(P\left( {s_n = \downarrow } \right) = P\left( {s_n = \uparrow } \right) = 1/2\). From the Bayes theorem, it follows for the more likely value of ς

$$P\left( {{\boldsymbol{m}}_n|s_n = \varsigma } \right) = \frac{{P\left( {s_n = \varsigma |{\boldsymbol{m}}_n} \right)P\left( {{\boldsymbol{m}}_n} \right)}}{{P\left( {s_n = \varsigma } \right)}}\, > \, \frac{{P\left( {s_n = \bar \varsigma |{\boldsymbol{m}}_n} \right)P\left( {{\boldsymbol{m}}_n} \right)}}{{P\left( {s_n = \bar \varsigma } \right)}} = P\left( {{\boldsymbol{m}}_n|s_n = \bar \varsigma } \right).$$
(5)

This means that we should now compare the likelihoods P(mn|sn = ↓) and P(mn|sn = ↑). Again, for optimal performance, we need to sum up probabilities of all (2n) possible spin trajectories \(\left\{ {s_0,s_1, \ldots s_{n - 1}} \right\}\) ending with sn = ς as

$$P\left( {{\boldsymbol{m}}_n|{\mathrm{s}}_n} \right) = \mathop {\sum }\limits_{s_0 = \downarrow }^ \uparrow \cdots \mathop {\sum }\limits_{s_{n - 1} = \downarrow }^ \uparrow \mathop {\prod }\limits_{i = 1}^n {\mathrm{\Theta }}_{s_{i - 1},s_i}\left( {\rho ^{s_{i - 1}}} \right){\mathrm{\Theta }}_{s_{i - 1},m_i}\left(\; {f_i^{s_{i - 1}}} \right).$$
(6)

In the main text, these Bayesian models are used to determine σ and ς.

Conversion between conditional probabilities

As explained in the main text, \(F_{\mathrm{P}}^{ \downarrow \left( \uparrow \right)}\) is defined by the conditional probability \(P\left( {s_n = \varsigma |\varsigma = \downarrow \left( \uparrow \right)} \right)\). Experimentally, sn can only be estimated with a finite fidelity from the ancilla measurement results \({\boldsymbol{m}}_{j,k}^\prime = \left\{ {m_j,m_{j\, +\, 1}, \cdots ,m_{j\, +\, k - 1}} \right\}\) with j ≥ n + 1. We denote such an estimator for sn as σ′ and its measurement fidelity as \(F_{\mathrm{M}}^{\prime s_n} \equiv P(\sigma^{\prime} = s_n|s_n).\) We can then convert \(P(\sigma^{\prime} = \varsigma |\varsigma )\) and \(F_{\mathrm{M}}^{\prime s_n}\) to \(F_{\mathrm{P}}^\varsigma\), by noting that for ς = ↓ and ↑,

$$\begin{array}{*{20}{l}} {P\left( {\sigma^{\prime} = \varsigma |\varsigma } \right)} \hfill & = \hfill & {P(\sigma ^{\prime} = \varsigma |s_n = \varsigma )P(s_n = \varsigma |\varsigma ) + P(\sigma^{\prime} = \varsigma |s_n = \bar \varsigma )P(s_n = \bar \varsigma |\varsigma )} \hfill \\ {} \hfill & = \hfill & {F_{\mathrm{M}}^{\prime \varsigma }F_{\mathrm{P}}^\varsigma + \left( {1 - F_{\mathrm{M}}^{\prime \bar \varsigma }} \right)\left( {1 - F_{\mathrm{P}}^\varsigma } \right).} \hfill \end{array}$$
(7)

Larger j − n and k would make the result more robust against correlated measurement errors and statistical shot noise, but j + k cannot exceed 30 (in the current experiment). We employ (j, k) = (n + 4,5) for Fig. 3e so that we can measure up to n = 20, and (n + 4,15) for Fig. 4 in order to obtain statistically more reliable results for high percentiles.

Data availability

The data that support the findings of this study are available from the corresponding authors upon reasonable request.

References

  1. 1.

    Veldhorst, M. et al. An addressable quantum dot qubit with fault-tolerant control-fidelity. Nat. Nanotechnol. 9, 981–985 (2014).

    ADS  CAS  Article  Google Scholar 

  2. 2.

    Yoneda, J. et al. A quantum-dot spin qubit with coherence limited by charge noise and fidelity higher than 99.9%. Nat. Nanotechnol. 13, 102–107 (2018).

    ADS  CAS  Article  Google Scholar 

  3. 3.

    Veldhorst, M. et al. A two-qubit logic gate in silicon. Nature 526, 410–414 (2015).

    ADS  CAS  Article  Google Scholar 

  4. 4.

    Huang, W. et al. Fidelity benchmarks for two-qubit gates in silicon. Nature 569, 532–536 (2019).

    ADS  CAS  Article  Google Scholar 

  5. 5.

    Watson, T. F. et al. A programmable two-qubit quantum processor in silicon. Nature 555, 633–637 (2018).

    ADS  CAS  Article  Google Scholar 

  6. 6.

    Zajac, D. M., Hazard, T. M., Mi, X., Nielsen, E. & Petta, J. R. Scalable gate architecture for a one-dimensional array of semiconductor spin qubits. Phys. Rev. Appl. 6, 054013 (2016).

    ADS  Article  Google Scholar 

  7. 7.

    Ralph, T. C., Bartlett, S. D., O’Brien, J. L., Pryde, G. J. & Wiseman, H. M. Quantum nondemolition measurements for quantum information. Phys. Rev. A 73, 012113 (2006).

    ADS  Article  Google Scholar 

  8. 8.

    Fowler, A. G., Mariantoni, M., Martinis, J. M. & Cleland, A. N. Surface codes: towards practical large-scale quantum computation. Phys. Rev. A 86, 032324 (2012).

    ADS  Article  Google Scholar 

  9. 9.

    Devoret, M. H. & Schoelkopf, R. J. Superconducting circuits for quantum information: an outlook. Science 339, 1169–1175 (2013).

    ADS  CAS  Article  Google Scholar 

  10. 10.

    Keith, D. et al. Benchmarking high fidelity single-shot readout of semiconductor qubits. N. J. Phys. 21, 063011 (2019).

    CAS  Article  Google Scholar 

  11. 11.

    Takeda, K. et al. A fault-tolerant addressable spin qubit in a natural silicon quantum dot. Sci. Adv. 2, e1600694 (2016).

    ADS  Article  Google Scholar 

  12. 12.

    Elzerman, J. M. et al. Single-shot read-out of an individual electron spin in a quantum dot. Nature 430, 431–435 (2004).

    ADS  CAS  Article  Google Scholar 

  13. 13.

    Yoneda, J. et al. Robust micromagnet design for fast electrical manipulations of single spins in quantum dots. Appl. Phys. Express 8, 84401 (2015).

    Article  Google Scholar 

  14. 14.

    Meunier, T., Calado, V. E. & Vandersypen, L. M. K. Efficient controlled-phase gate for single-spin qubits in quantum dots. Phys. Rev. B 83, 121403 (2011).

    ADS  Article  Google Scholar 

  15. 15.

    Reed, M. D. et al. Reduced sensitivity to charge noise in semiconductor spin qubits via symmetric operation. Phys. Rev. Lett. 116, 110402 (2016).

    ADS  CAS  Article  Google Scholar 

  16. 16.

    Yoneda, J. et al. Fast electrical control of single electron spins in Quantum dots with vanishing influence from nuclear spins. Phys. Rev. Lett. 113, 267601 (2014).

    ADS  CAS  Article  Google Scholar 

  17. 17.

    Takeda, K. et al. Optimized electrical control of a Si/SiGe spin qubit in the presence of an induced frequency shift. npj Quantum Inf. 4, 54 (2018).

    ADS  Article  Google Scholar 

  18. 18.

    Nakajima, T. et al. Quantum non-demolition measurement of an electron spin qubit. Nat. Nanotechnol. 14, 555–560 (2019).

    ADS  CAS  Article  Google Scholar 

  19. 19.

    Pla, J. J. et al. High-fidelity readout and control of a nuclear spin qubit in silicon. Nature 496, 334–338 (2013).

    ADS  CAS  Article  Google Scholar 

  20. 20.

    Hensen, B. et al. A silicon quantum-dot-coupled nuclear spin qubit. Nat. Nanotechnol. 15, 13–17 (2020).

    ADS  CAS  Article  Google Scholar 

  21. 21.

    Borjans, F., Zajac, D. M., Hazard, T. M. & Petta, J. R. Single-spin relaxation in a synthetic spin-orbit field. Phys. Rev. Appl. 11, 044063 (2019).

    ADS  CAS  Article  Google Scholar 

  22. 22.

    Noiri, A. et al. A fast quantum interface between different spin qubit encodings. Nat. Commun. 9, 5066 (2018).

    ADS  CAS  Article  Google Scholar 

  23. 23.

    Noiri, A. et al. Coherent electron-spin-resonance manipulation of three individual spins in a triple quantum dot. Appl. Phys. Lett. 108, 153101 (2016).

    ADS  Article  Google Scholar 

  24. 24.

    Meunier, T. et al. Nondestructive measurement of electron spins in a quantum dot. Phys. Rev. B 74, 195303 (2006).

    ADS  Article  Google Scholar 

Download references

Acknowledgements

We thank Microwave Research Group at Caltech for technical assistance. Part of this work was financially supported by CREST, JST (JPMJCR15N2, JPMJCR1675), the ImPACT Program of Council for Science, Technology and Innovation (Cabinet Office, Government of Japan), MEXT Quantum Leap Flagship Program (MEXT Q-LEAP) Grant Number JPMXS0118069228, JSPS KAKENHI Grants Nos. 26220710, 17K14078, 18H01819, and 19K14640, RIKEN Incentive Research Projects and The Murata Science Foundation.

Author information

Affiliations

Authors

Contributions

J.Y. acquired and analyzed the data and wrote the paper. K.T. and A.N. set up the measurement hardware with assistance from J.Y., T.N., and S.L. T.N. contributed to the data analysis. K.T. fabricated the device with help from J.K. and T.K. S.T. supervised the project.

Corresponding authors

Correspondence to J. Yoneda or S. Tarucha.

Ethics declarations

Competing interests

The authors declare no competing interests.

Additional information

Peer review information Nature Communications thanks the anonymous reviewers for their contribution to the peer review of this work. Peer reviewer reports are available.

Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary information

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Yoneda, J., Takeda, K., Noiri, A. et al. Quantum non-demolition readout of an electron spin in silicon. Nat Commun 11, 1144 (2020). https://doi.org/10.1038/s41467-020-14818-8

Download citation

Further reading

Comments

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

Search

Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing