Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

# Dynamical nonlinear memory capacitance in biomimetic membranes

### Subjects

An Author Correction to this article was published on 21 August 2019

## Abstract

Two-terminal memory elements, or memelements, capable of co-locating signal processing and memory via history-dependent reconfigurability at the nanoscale are vital for next-generation computing materials striving to match the brain’s efficiency and flexible cognitive capabilities. While memory resistors, or memristors, have been widely reported, other types of memelements remain underexplored or undiscovered. Here we report the first example of a volatile, voltage-controlled memcapacitor in which capacitive memory arises from reversible and hysteretic geometrical changes in a lipid bilayer that mimics the composition and structure of biomembranes. We demonstrate that the nonlinear dynamics and memory are governed by two implicitly-coupled, voltage-dependent state variables—membrane radius and thickness. Further, our system is capable of tuneable signal processing and learning via synapse-like, short-term capacitive plasticity. These findings will accelerate the development of low-energy, biomolecular neuromorphic memelements, which, in turn, could also serve as models to study capacitive memory and signal processing in neuronal membranes.

## Introduction

Neuromorphic computing systems striving to match the density, interconnectivity, and efficiency of the brain require highly parallelized networks of dynamic elements and materials that co-locate signal processing and memory—just like biological synapses1,2,3,4. Although three-terminal transistors are being used5,6,7,8 for this purpose, they require complex circuits to emulate synapses, are power hungry9, and their scaling is limited by the imminent end of Moore’s Law3,10. Two-terminal memory elements, i.e., memelements1,11,12,13,14, that are able to store and process information through history-dependent material reconfigurations at the nanoscale, offer an alternative path to greater functional density and reduced energy consumption. By definition, memelements are devices with resistance, capacitance, or inductance that depend on their past electrical activity14. While many types of memory resistors, i.e., memristors, have been introduced15,16,17,18, to date, only a sparse collection of physically realized memory capacitors19,20,21,22,23,24,25,26,27,28,29,30 and one pseudo-memcapacitor31 have been reported, despite their promise to further lower static power dissipation. Of these, most did not provide evidence of pinched hysteresis in the charge-voltage plane as proof of memory capacitance, as first defined by Chua14,32, or develop realistic, physics-based models to describe and predict the state variables driving capacitive reconfigurations. Devices for which ideal, analogue memcapacitance that originates from geometrical changes in materials at the molecular scale remain unrealized to date.

We recently demonstrated that a synthetic biomembrane (i.e., lipid bilayer) doped with voltage-activated ion channels exhibits volatile memory resistance governed by two voltage-dependent state variables: the areal density of ion channels and the increase in membrane area due to electrowetting16. We have also shown that the spike-rate-dependent plasticity (SRDP) exhibited by these two-terminal memristors enable them to function as resistive synapses for online learning in spike recurrent neural networks built from solid-state neurons33,34. Based on these findings we hypothesized that an insulating lipid bilayer, without conductive ion channels, may exhibit capacitive memory governed solely by voltage-dependent changes to the dimensions of the dielectric dominated by the hydrophobic core of the bilayer.

Here we report that adhering, lipid-encased, aqueous droplets in oil yields an interfacial biomimetic membrane (3–5 nm thick) that exhibits volatile, analogue memcapacitance via voltage-controlled geometric reconfigurability. Pinched hysteresis in both the charge-voltage and capacitance-voltage planes result from dynamic changes in interfacial area and hydrophobic thickness, each of which are nonlinearly dependent on voltage. Through experimentation and modelling, we demonstrate this assembly is a volatile, second-order, generic memcapacitor32 capable of synapse-like temporal filtering and learning through short-term plasticity. Our results forecast new classes of biomimetic, low-power memelements based on soft, organic materials and biomolecules, which, in turn, will aid in exploring capacitive memory and susceptibility in neuronal membranes.

## Results

### A two-terminal biomolecular memcapacitor

Inspired by plasma membranes (Supplementary Note 1)35, we have developed a two-terminal, biomimetic assembly with dynamical, nonlinear memory capacitance via voltage-controlled geometric reconfigurability. The system consists of an elliptical, planar lipid bilayer that forms at an interface between two lipid-coated aqueous droplets (~200 nL each) in oil (Fig. 1a and Supplementary Figs. 13). With this structure, the hydrophobic lipid acyl chains and any residual oil (each with a dielectric constant of ~2–3) form a low-leakage (membrane resistance > 100 MΩ cm2)16,36, parallel-plate capacitor (0.1–1 µF cm−2)37 that inhibits diffusive transport between droplets. As is well established, the series capacitance formed by the electric double layer (~75 μF cm−2)38 of ions on each face of the membrane can be ignored since it is much larger in value than that of the hydrophobic region of the membrane (~0.4–0.65 μF cm−2; Supplementary Note 2). The assembly process, interface geometry, and physical properties are detailed in Supplementary Note 3 and elsewhere16,37. We use synthetic 1,2-diphytanoyl-sn-glycero-3-phosphocholine (DPhPC) lipids, known for their chemical stability and low ion permeability39, to construct capacitive bilayer interfaces, though other lipid types40,41 or polymers42 may also be used. Membranes are assembled in decane (C10H22) and hexadecane (C16H34) oils to study the effect of alkane length and viscosity (0.86 and 3.04 mN s m−2, respectively)43 on voltage-dependent bilayer geometry. At zero membrane potential, the specific capacitance of a DPhPC bilayer in decane is 0.46 μF cm−2 (equivalent hydrophobic thickness, W0 ~ 3.8 nm), versus 0.68 μF cm−2 (W0 ~ 2.6 nm) in hexadecane (Supplementary Fig. 4). A thicker bilayer with decane results from more residual oil in the membrane (~43% by volume) due to the shorter chain length of decane44 (versus ~10% for hexadecane45). By comparison, the specific capacitance of a neural membrane46 is ~0.90 μF cm−2. Further, the zero-volt minor axis radii (R0) of elliptical interfaces formed in decane and hexadecane are ~100 μm and ~250 μm, respectively (see Supplementary Movies 13), due to oil-dependent differences in monolayer tensions37 (see Supplementary Notes 35 and Supplementary Fig. 3).

Subjected to a nonzero bias, v(t), ions rapidly accumulate on both sides of the membrane where they exert parallel and perpendicular forces that can affect the geometry of the interface. For a typical bilayer with nominal capacitance of ~500–1000 pF and aqueous droplets with solution resistance of ~10 kΩ, the time constant for charging or discharging the membrane is ~10 µs. Therefore, at frequencies well below ~15 kHz, ion movements within the electric double layer are quasi-static with respect to AC voltage. Voltage-driven geometrical changes can include: (1) the formation of new bilayer area at constant thickness37 due to charge-induced reductions in bilayer tension—electrowetting (EW)37—described by the Young-Lippmann equation47 (Supplementary Movies 4 and 5); and (2) a decrease in thickness—electrocompression (EC)16—that may or may not affect bilayer area. In oil-free membranes, EC of the hydrophobic acyl chains is explicitly coupled to increased area at constant volume, due to the Poisson effect48. However, EC of bilayers containing residual oil trapped between lipid leaflets (e.g., DPhPC bilayers in decane or hexadecane) expels the oil rather than deforming the acyl chains. Thus, changes in thickness do not affect membrane area (i.e., no stretching)45 (see Supplementary Note 5 and Supplementary Fig. 4).

Because radius, R(t), and hydrophobic thickness, W(t) are affected via EW and EC in our system, we expect the relationship between charge, Q, and applied voltage, v, to be described by

$$Q = C\left( {R,W} \right)v$$
(1)

where R and W are voltage-controlled state variables, and the memcapacitance, C, for a parallel-plate capacitor with planar ellipticity, a, and equivalent dielectric constant, ε, is given by

$$C\left( {R,W} \right) = \frac{{\varepsilon \varepsilon _0\left( {a\pi R\left( t \right)^2} \right)}}{{W(t)}}.$$
(2)

Because the dielectric constants of decane, hexadecane, and the hydrophobic core of the bilayer (2, 2.09, and 2.1 respectively) are very similar, we do not anticipate significant changes in the effective dielectric constant upon EC-induced thinning that depletes the amount of oil between lipid leaflets. Based on the full derivation in Supplementary Notes 6 and 7, the dynamical state equation for R is given by

$$\frac{{\mathrm{d}R(t)}}{{\mathrm{d}t}} = \frac{1}{{\xi _{{\mathrm{ew}}}}}\left( {\frac{{a\varepsilon \varepsilon _0}}{{2W\left( t \right)}}v\left( t \right)^2 - k_{{\mathrm{ew}}}\left( {R\left( t \right) - R_0} \right)} \right)$$
(3)

where $$\xi _{{\mathrm{ew}}}$$ and $$k_{{\mathrm{ew}}}$$ are the effective damping (N s m−2) and stiffness (N m−2) coefficients, respectively, in the tangential direction. Similarly, the state equation for W is given by

$$\frac{{\mathrm{d}W(t)}}{{\mathrm{d}t}} = \frac{1}{{\xi _{{\mathrm{ec}}}}}\left( { - \frac{{\varepsilon \varepsilon _0a\pi R\left( t \right)^2}}{{2W\left( t \right)^2}}v\left( t \right)^2 + k_{{\mathrm{ec}}}\left( {W_0 - W\left( t \right)} \right)} \right)$$
(4)

where $$\xi _{{\mathrm{ec}}}$$, and $$k_{{\mathrm{ec}}}$$ are the effective damping (N s m−1) and stiffness (N m−1) coefficients, respectively, in the normal direction. These nonlinear, implicitly-coupled state equations stem from electrical forces exerted on the membrane that are themselves functions of R and W (see Supplementary Note 7 and Supplementary Fig. 5).

### Dynamical response and pinched hysteresis

We first measure the dynamical capacitance of DPhPC lipid membranes in response to a bipolar alternating bias, v(t), at room temperature (RT ~ 22 °C) (Fig. 2). These data reveal basic information about the dynamical responses of our biomimetic system: First, bilayer capacitance exhibits a positive DC offset at steady state, following an exponential transient period of 2–20 s, induced by the root mean square of the voltage. Second, dynamical capacitance shows a doubling of the excitation frequency due to the squaring of membrane voltage in Eqs. 3, 4, indicating the process is proportional to the power and independent of the sign of the applied AC voltage. Third, for symmetric membranes at steady state, the capacitance is minimum at zero applied potential (Fig. 3a, b) and the amplitude of capacitance oscillations decreases with increasing excitation frequency, consistent with Chua’s explanation that memristor pinched hysteresis collapses to a simple curve (Fig. 3) at high frequency because the system cannot follow the driving excitation14. Finally, these measurements highlight the fact that the capacitance of a bilayer formed in decane is more responsive to voltage compared to one in hexadecane, especially at 1.7 Hz (Fig. 2d), due to the reduced viscosity of decane and the fact that greater increases in area and decreases in thickness are possible due to higher zero-volt thickness and zero-voltage monolayer tension of DPhPC membranes in decane that make them more susceptible to EC and EW.

To investigate the memcapacitance, we plot both the steady-state dynamic capacitance versus voltage (C-v) and charge versus voltage (Q-v) relationships (Fig. 3, see “Methods”). For both oils, we observe: (1) symmetric, nonlinear, nonhysteretic relationships at lower frequencies (<0.005 Hz) (Supplementary Fig. 6); (2) symmetric, nonlinear, pinched hysteresis Q-v loops at intermediate frequencies (Fig. 3c, d); and (3) symmetric, linear, nonhysteretic relationships implying fixed capacitance, C, at higher frequencies (>5 Hz and >2 Hz for decane and hexadecane, respectively) (Figs. 2, 3).

The nonlinear changes and pinched hysteresis in Q-v responses at low and intermediate frequencies arise from reversible, hysteretic changes in C (Fig. 3a, b and upper insets of Fig. 3c, d), caused by EW and EC as described in Fig. 1b and Eqs. 24. These bipolar sweeps also show that a DPhPC bilayer in decane displays larger relative changes in C-v, and both stronger nonlinearity and more pronounced hysteresis in Q-v compared to hexadecane. Membranes in decane also exhibit a wider range of intermediate frequencies where pinched hysteresis in Q-v occurs. The former makes sense because oil-rich membranes display higher tensions and thicknesses, conditions where EW and EC can create larger geometrical changes (Supplementary Fig. 7)44 compared to oil-poor bilayers with weaker voltage dependencies (Supplementary Fig. 8). The latter is consistent with the fact that lower oil viscosity allows changes to occur more quickly (Supplementary Fig. 4). We also obtain Q-v measurements for a bilayer in hexadecane at 50 °C (Supplementary Fig. 9) to demonstrate that oil viscosity impacts hysteresis separately from alkane tail length. As expected, the heated system exhibits more pronounced Q-v hysteresis compared to room temperature. The lower insets in Fig. 3c, d display the memory-associated energy (Methods) dissipated in response to a sinusoidal v(t) at 0.017 Hz. These energy results demonstrate that a lipid bilayer memcapacitor is a passive device that dissipates energy to drive geometrical changes at the interface and dynamically reconfigure C. And because changes in geometry and C are not stored (i.e., R and W return to R0 and W0, respectively, when the voltage is removed), this system exhibits volatile memcapacitance.

We also measure C induced by stepwise changes in voltage from 0 to 150 mV (0.025 Hz, 50% duty cycle) to estimate time constants for increases and decreases in C (Supplementary Figure 7). For both oils, increases in C are slower ($$\tau _{{\mathrm{rise}}}\sim$$ 2.2 s and 3.7 s for decane and hexadecane, respectively) than decreases in C ($$\tau _{{\mathrm{decay}}}\sim$$ 0.46 s and 1.59 s, respectively). Faster decreases in C are helpful in creating pinched hysteresis during decreasing voltage portions of a sweep. Not only are $$\tau _{{\mathrm{rise}}}$$ and $$\tau _{{\mathrm{decay}}}$$ for decane smaller than for hexadecane, but the ratio $$\tau _{{\mathrm{rise}}}/\tau _{{\mathrm{decay}}}$$ is higher. Furthermore, we found that the percentage increase in C in hexadecane matches that of the membrane area (~25%), indicating that only EW causes the change in C, and EC is negligible. Conversely, a bilayer in decane exhibited an increase in C of 150%, even though the bilayer area only increased by 80%. This discrepancy suggests W had to have decreased by ~28% to create the additional 70% rise in net capacitance. Comparing the dynamic changes in C to membrane area (Supplementary Fig. 7) also reveals that EW $$\left( {\tau _1\;\sim \;2.2\;{\mathrm{s}}} \right)$$ results in faster increases in C than EC $$\left( {\tau _2\sim 16\;{\mathrm{s}}} \right)$$. Coincidentally these time constants for geometric reconfiguration are quite similar to the time constants (~1 s) attributed to hysteretic ion rearrangement on the surfaces of charged, glass nanopores49,50, despite the differences in physical origins for hysteretic charging versus ac voltage. Note that if ion channels were present in the lipid membrane, the Q-v relationship would resemble that of a leaky capacitor (i.e., hysteretic, but not pinched due to additional ohmic current). Still, the capacitive memory will be present as both EW and EC phenomena remain.

Unlike many memelements, our system is highly modular and uniquely bio-inspired. By changing the composition of one leaflet of the bilayer from DPhPC to DOPhPC (1,2-di-O-phytanoyl-sn-glycero-phosphocholine) lipids (Fig. 4), we create an asymmetric bilayer with a constant intrinsic bias, analogous to the resting potential of a cell (~−70 mV)51, produced by the difference of lipid dipole potentials52. This means when v= 0, the net membrane potential, vm = v + vint, equals vint (~−137 mV), which results in a thinner membrane (W ~3.5 nm) with larger interfacial area (R ~170 μm), due to EC and EW, compared to symmetric leaflets for which vm = vint= 0. The value of v for which the effects of EW and EC on C are minimized is equal to + 137 mV, not zero (Fig. 4a, b and Supplementary Fig. 10). Plotting the Q-v relationships for the asymmetric devices (Fig. 4c, d) displays asymmetric pinched-hysteresis loops, where the largest hysteresis lobes occur in the third quadrant where the magnitudes of v and vint add.

### Signal processing via short-term plasticity

Storing and processing information in the brain depends on continuously changing the strength of synaptic communication between neurons, a process known as synaptic plasticity. Ubiquitous in the brain, short-term synaptic plasticity (STP) is thought to play a significant role in information transfer and neural processing, including spatiotemporal filtering that enables selective transmission of specific patterns of neural activity53. Presynaptic STP can last from milliseconds to minutes and is often divided into three categories: depression, facilitation, and augmentation. Facilitating and augmenting synapses act as high-pass filters by increasing their conductances during subsequent bursts of incoming signals, which strengthen communication between connected neurons53. On the other hand, depressing synapses function as low-pass filters by reducing their conductances during bursts of activity, resulting in lower transmission rates and connection strengths between neurons.

To investigate short-term plasticity in purely capacitive, lipid-only interfaces, we stimulate them with trains of voltage pulses and record their dynamic current responses (Fig. 5). We discover that for a fixed ON-time (2 ms), and a range of OFF-times (1–50 ms), bilayers accumulate changes in capacitance, causing sequential increases in peak capacitive current $$( {I_{{\mathrm{peak}}} = C \cdot {\mathrm{d}}v/{\mathrm{d}}t} )$$, which emulate high-pass filtering via short-term facilitation in synapses53. Figure 5b–e shows responses of DPhPC bilayers to 150 mV, 2 ms ON pulses separated by 0 mV, 1 ms OFF periods. For all cases, peak capacitive currents increased monotonically across successive pulses until reaching steady state (Supplementary Fig. 11 provides total current responses). Consistent with Supplementary Figure 7, bilayers in decane exhibited an initial faster adaptation to the stimulus ($$\tau _1$$ ~ 2 s) caused by EW, followed by a slower adaptation ($$\tau _2$$ ~ 16 s) linked to EC. In contrast, bilayers in hexadecane exhibited only one time constant ($$\tau$$ ~ 3.7 s), attributed to EW.

As discussed earlier, asymmetric devices can exhibit minimum capacitance at a nonzero applied potential. The consequence of this shift is that an asymmetric DPhPC:DOPhPC membrane exhibits a depression-like cumulative decrease in peak current (Fig. 5e) in response to a pulse stimulation of v = + 150 mV (vm = v + vint = + 13 mV)—emulating another vital type of STP54. Moreover, short-term learning responses also become asymmetric with respect to polarity: applying −150 mV causes faciliatory behaviour, as the magnitudes of both v and vint sum (vm ~−287 mV) to increase C (Fig. 5e). Facilitating responses are also possible for positive v by sufficiently raising the pulse amplitude; however, dielectric breakdown is common for |vm| > 300 mV.

Figure 5f compares facilitation-like responses versus stimulus interval from symmetric membranes in decane and hexadecane. These signal processing features suggest this type of device could be tuned for use as a high-pass or low-pass filter, or as a memcapacitive synapse with online short-term learning capabilities31,54. We are currently combining multiple symmetric and asymmetric leaflet membranes to achieve facilitation followed by depression, and vice versa.

### Simulations of memory capacitance

After confirming volatile memcapacitance, we applied a simultaneous, nonlinear least squares fitting routine (Supplementary Methods) to independent, representative measurements of both C and R induced by sine wave voltages to estimate values (Table 1) for the equivalent damping and stiffness terms in Eqs. 3, 4 and, for decane, assess the relative contributions of EW and EC on Q-v shape. Estimates of $$k_{{\mathrm{ew}}}$$ (units of tension/length) for bilayers in hexadecane are significantly higher than those in decane, confirming that bilayers in decane are more compliant to EW forces. The lower mean values of EW time constants, $$\tau _{{\mathrm{ew}}} = \xi _{{\mathrm{ew}}}/k_{{\mathrm{ew}}}$$, for decane also confirm that EW is faster for the smaller, less viscous alkane. The values of the EC-fitted parameters in Table 1 highlight the fact that EC results in slower dynamics and greater resistance to changes in membrane geometry (thickness versus area) compared to EW. Moreover, we found that the damping and stiffness parameters for EW and EC varied with frequency. From this, we surmise this variation in measured materials properties stems from the interfacial membrane not being a closed system with constant volume, since the amount of oil trapped within the hydrophobic core of the membrane at steady state changes with the driving frequency. This variation is expected to yield differences in the measured material properties. Similar phenomena have been observed for squeeze-film damping systems, where both damping and stiffness parameters are functions of the spacing between the plates55.

With these values, we simulated responses of the membrane to sinusoidal applied voltages (Fig. 68 and Supplementary Figs. 1219) and computed the percent contributions of EW (changes in R) and EC (changes in W) to dynamic capacitance at steady state as functions of excitation frequency for decane (Fig. 5a). These comparisons reveal that: (1) EW contributes more than 80% of the change in C at all frequencies; and (2) the contributions of EC, which has a larger time constant, diminish with increasing frequency. As a result, we conclude that EW is the dominant mechanism for changing capacitance (and thus hysteresis) for DPhPC bilayers, and that bilayers in decane exhibit greater changes in capacitance, more pronounced nonlinearity (Supplementary Fig. 13), and greater Q-v hysteresis than hexadecane due to greater compliance of bilayers in decane to EW and the reduction of bilayer thickness due to EC, which is negligible for hexadecane.

Figures 6 and 8b show simulated R(t), W(t), and Q-v relationships (at steady state), respectively, induced by sinusoidal voltages for DPhPC bilayers in hexadecane and decane, proving the model captures the frequency dependence of this system. Further, the model can predict the dynamic responses to rectangular voltage pulses, such as those measured experimentally for Fig. 5. Figure 8c shows that the minor axis radius of a bilayer in decane grows quickly by ~35%, accompanied by a slower, smaller (~20%) decrease in thickness. Based on these geometrical reconfigurations of the capacitance, the model also predicts facilitation and depression, respectively, of the peak currents for both symmetric and asymmetric membranes, with the latter simulated by replacing v(t) with v(t)−137 mV in Eqs. 3, 4 (Fig. 8d).

## Discussion

Using a soft, modular, and biomimetic membrane that mimics the composition and structure of cellular membranes, we demonstrate volatile memcapacitance via geometrical reconfigurability. Memcapacitive and nonlinear dynamical behaviours, including capacitive short-term facilitation and depression, are found to be governed by two implicitly-coupled, voltage-dependent state variables: membrane radius, R, and hydrophobic thickness, W. When the bilayer contained less residual oil (e.g., hexadecane), electrowetting is the sole mechanism for variable capacitance (i.e., resulting in a first-order memcapacitor). But when more oil was retained between leaflets (decane) and when this oil had a lower viscosity, both EW and EC contribute to the total change in capacitance, causing Q-v to exhibit stronger nonlinearity and reconfigure more quickly to changes in voltage (the decane system is considered a second-order memcapacitor).

In addition to their possible implementation as capacitive synaptic mimics56 in spike recurrent neural networks for online learning and computation, we envision this system to have impact in two major areas: (1) modular, low-power materials that could interface with cells and tissues for biosensing and processing of biological signals due to their soft and biocompatible nature57; and (2) as a model system to study capacitive excitability in neuronal membranes. The current system differs from biological membranes by having residual oil in the hydrophobic core of the membrane. However, choosing a higher molecular weight oil and naturally-derived lipids could yield more biologically-relevant interfaces with specific capacitances closer to those of biological neurons. We have previously found that membranes from natural sources such as porcine brain total lipid extract, which contains hundreds of distinct lipid types and large amounts of cholesterol, undergo entropic, higher-order phase transitions detectable with capacitance40. Higher-order transitions such as these are believed to be important in cell signalling and dynamic lipid domain (i.e., raft) formation, based on high-amplitude yet nanoscopic and fleeting stochastic fluctuations located near critical points, instead of abrupt changes in molecular composition or density inherent to first-order enthalpic transitions, which tend to be more disruptive to membranes. In the presence of electric fields, charges exert forces on the membrane that can change its molecular ordering via electrostriction (EW and EC). This results in a capacitive susceptibility that replaces the common assumption of constant capacitance, which, up to now, has dominated electrophysiological descriptions and characterizations of biomembranes. Such experiments could bring completely new insights regarding the capacitive susceptibility of neuronal membranes, and therefore, may impact the Hodgkin-Huxley model for excitability, which assumes capacitance to be a constant.

## Methods

### Preparation of lipid solutions and membrane assembly

The aqueous droplets consist of deionized water (18.2 MΩ.cm) containing 2 mg ml−1 of either DPhPC or DOPhPC liposomes, 500 mM potassium chloride (KCl, Sigma), and 10 mM 3-(N-morpholino)propanesulfonic acid (MOPS, Sigma), with a pH of 7.0. Both DPhPC and DOPhPC liposomes vesicles are prepared and stored as described elsewhere37. To help the droplets anchor to the silver/silver chloride (Ag/AgCl) wires (Goodfellow), we coat their ball-ended tips with a 1% agarose gel solution. The oil surrounding the droplets consists of either decane (≥95%, Sigma) or hexadecane (≥99%, Sigma). Lipid membranes are formed between two aqueous droplets anchored to wire-type electrodes in a transparent reservoir filled with oil, as described elsewhere16,37,41.

### Electrical measurements

To record the lipid membrane formation, which is reflected as an increase in membrane capacitance, we supply a 10 Hz, 10 mV triangular wave to the electrodes using a function generator. Due to the capacitive nature of the membrane, the resulting current response is square-like (Supplementary Fig. 2). As the area of the thinned lipid membrane grows, the peak-to-peak current amplitude increases until reaching a steady state (Supplementary Fig. 2). To obtain the C-v and Q-v plots, we use a custom LabView code to apply a low-frequency, high-amplitude sinusoidal voltage waveform (amplitude and frequencies are mentioned in the main text) overlaid with a 10 mV, 100 Hz triangular voltage waveform output from an Agilent 33210A waveform generator. While the low-frequency, sinusoidal waveform drives geometrical changes at the lipid interface (i.e., EW and EC), the capacitance measurements are based on the lipid membrane’s current response to the higher frequency triangular waveform. The capacitance of the lipid interface is then extracted from sections of the square-wave current response using a custom MATLAB script (available upon request). In parallel, to monitor the changes in the membrane’s minor axis radius, R, we acquire images of the droplets as viewed from below through a 4x objective lens on an Olympus IX51 inverted microscope using a QI Click CCD. We then post-process the images using custom scripts in MATLAB to extract values of R. For the signal pulse experiments, we use a custom LabView code to generate pulses with specific amplitudes and ON and OFF times. All current recordings are made using an Axopatch 200B patch clamp amplifier and Digidata 1440 data acquisition system (Molecular Devices). For all measurements, droplets and measurement probes are placed under a lab-made Faraday cage to minimize noise from the environment. To obtain the energy dissipation displayed in Fig. 3, we integrate with respect to time the product of applied voltage bias, v(t), and capacitive current, Ic, given by

$$I_{\mathrm{c}} = C\frac{{\mathrm{d}v(t)}}{{\mathrm{d}t}} + v\left( t \right)\frac{{\mathrm{d}C}}{{\mathrm{d}t}},$$
(5)

where C the memcapacitance of the lipid membrane and v(t) is the voltage bias.

## Data availability

All relevant data that support the findings of this study are available from the corresponding authors on reasonable request.

## Change history

• ### 21 August 2019

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

## References

1. 1.

Di Ventra, M. & Pershin, Y. V. The parallel approach. Nat. Phys. 9, 200–202 (2013).

2. 2.

Bresniker, K. M., Singhal, S. & Williams, R. S. Adapting to thrive in a new economy of memory abundance. Computer 48, 44–53 (2015).

3. 3.

Williams, R. S. What’s next? Comput. Sci. Eng. 19, 7–13 (2017).

4. 4.

van de Burgt, Y., Melianas, A., Keene, S. T., Malliaras, G. & Salleo, A. Organic electronics for neuromorphic computing. Nat. Electron. 1, 386–397(2018).

5. 5.

Mead, C. Neuromorphic electronic systems. Proc. IEEE 78, 1629–1636 (1990).

6. 6.

Merolla, P. A. et al. A million spiking-neuron integrated circuit with a scalable communication network and interface. Science 345, 668–673 (2014).

7. 7.

Furber, S. Large-scale neuromorphic computing systems. J. Neural Eng. 13, 051001 (2016).

8. 8.

Furber, S. B., Galluppi, F., Temple, S. & Plana, L. A. The spinnaker project. Proc. IEEE 102, 652–665 (2014).

9. 9.

Williams, R. S. How we found the missing memristor. IEEE Spectrum 45, 28–35 (2008).

10. 10.

Waldrop, M. M. The chips are down for Moore’s law. Nature 530, 144–147 (2016).

11. 11.

Chua, L. O. Nonlinear circuit foundations for nanodevices. I. The four-element torus. Proc. IEEE 91, 1830–1859 (2003).

12. 12.

Chua, L. Memristor-the missing circuit element. IEEE Trans. Circuit Theory 18, 507–519 (1971).

13. 13.

Di Ventra, M., Pershin, Y. V. & Chua, L. O. Circuit elements with memory: memristors, memcapacitors, and meminductors. Proc. IEEE 97, 1717–1724 (2009).

14. 14.

Yin, Z., Tian, H., Chen, G. & Chua, L. O. What are memristor, memcapacitor, and meminductor?. IEEE T. Circuits-II 62, 402–406 (2015).

15. 15.

Strukov, D. B., Snider, G. S., Stewart, D. R. & Williams, R. S. The missing memristor found. Nature 453, 80–83 (2008).

16. 16.

Najem, J. S. et al. Memristive ion channel-doped biomembranes as synaptic mimics. ACS Nano 12, 4702–4711 (2018).

17. 17.

Prodromakis, T., Toumazou, C. & Chua, L. Two centuries of memristors. Nat. Mater. 11, 478 (2012).

18. 18.

Li, Y., Wang, Z., Midya, R., Xia, Q. & Yang, J. J. Review of memristor devices in neuromorphic computing: materials sciences and device challenges. J. Phys. D 51, 503002 (2018).

19. 19.

Bessonov, A. A. et al. Layered memristive and memcapacitive switches for printable electronics. Nat. Mater. 14, 199 (2015).

20. 20.

Chu, H.-L. et al. Exploration and characterization of the memcapacitor and memristor properties of Ni–DNA nanowire devices. NPG Asia Mater. 9, e430 (2017).

21. 21.

Yan, Z. & Liu, J.-M. Coexistence of high performance resistance and capacitance memory based on multilayered metal-oxide structures. Sci. Rep. 3, 2482 (2013).

22. 22.

Park, D. et al. Analog reversible nonvolatile memcapacitance in metal-oxide-semiconductor memcapacitor with ITO/HfOx/Si structure. Appl. Phys. Lett. 113, 162102 (2018).

23. 23.

Wang, D. et al. Transmembrane potential across single conical nanopores and resulting memristive and memcapacitive ion transport. J. Am. Chem. Soc. 134, 3651–3654 (2012).

24. 24.

Lai, Q. et al. Analog memory capacitor based on field-configurable ion-doped polymers. Appl. Phys. Lett. 95, 213503 (2009).

25. 25.

Qingjiang, L. et al. Memory impedance in TiO 2 based metal-insulator-metal devices. Sci. Rep. 4, 4522 (2014).

26. 26.

Valov, I. et al. Nanobatteries in redox-based resistive switches require extension of memristor theory. Nat. Commun. 4, 1771 (2013).

27. 27.

Park, M., Park, S. & Yoo, K.-H. Multilevel nonvolatile memristive and memcapacitive switching in stacked graphene sheets. ACS Appl. Mater. Interfaces 8, 14046–14052 (2016).

28. 28.

Shuai, Y. et al. Coexistence of memristive and memcapacitive effects in oxide thin films. Jpn. J. Appl. Phys. 57, 121502 (2018).

29. 29.

Martino, N. & Randriamahazaka, H. N. Memcapacitive properties of poly (3, 4-ethylenedioxythiophene) modified electrodes. Electrochem. Commun. 28, 63–66 (2013).

30. 30.

Pershin, Y. V. & Di Ventra, M. Memory effects in complex materials and nanoscale systems. Adv. Phys. 60, 145–227 (2011).

31. 31.

Wang, Z. et al. Capacitive neural network with neuro-transistors. Nat. Commun. 9, 3208 (2018).

32. 32.

Leon, C. Everything you wish to know about memristors but are afraid to ask. Radioengineering 24, 319 (2015).

33. 33.

Weiss, R. et al. A soft-matter biomolecular memristor synapse for neuromorphic systems. In 2018 IEEE Biomedical Circuits and Systems Conference (BioCAS). (IEEE, Cleveland, 2018).

34. 34.

Hasan, M. S. et al. Biomimetic, soft-material synapse for neuromorphic computing: from device to network. In 2018 IEEE 13th Dallas Circuits and Systems Conference (DCAS). (IEEE, Dallas, 2018).

35. 35.

Edidin, M. Lipids on the frontier: a century of cell-membrane bilayers. Nat. Rev. Mol. Cell Biol. 4, 414 (2003).

36. 36.

Sarles, S. A. & Leo, D. J. Regulated attachment method for reconstituting lipid bilayers of prescribed size within flexible substrates. Anal. Chem. 82, 959–966 (2010).

37. 37.

Taylor, G. J., Venkatesan, G. A., Collier, C. P. & Sarles, S. A. Direct in situ measurement of specific capacitance, monolayer tension, and bilayer tension in a droplet interface bilayer. Soft Matter 11, 7592–7605 (2015).

38. 38.

Peitzsch, R. M., Eisenberg, M., Sharp, K. A. & McLaughlin, S. Calculations of the electrostatic potential adjacent to model phospholipid bilayers. Biophys. J. 68, 729–738 (1995).

39. 39.

Andersson, M. et al. Vesicle and bilayer formation of diphytanoylphosphati-dylcholine (DPhPC) and diphytanoylphosphatidylethanolamine (DPhPE) mixtures and their bilayers’ electrical stability. Colloids Surf. B: Biointerfaces 82, 550–561 (2011).

40. 40.

Taylor, G. J. et al. Capacitive detection of low-enthalpy, higher-order phase transitions in synthetic and natural composition lipid membranes. Langmuir 33, 10016–10026 (2017).

41. 41.

Taylor, G. J. & Sarles, S. A. Heating-enabled formation of droplet interface bilayers using Escherichia coli total lipid extract. Langmuir 31, 325–337 (2014).

42. 42.

Tamaddoni, N., Taylor, G., Hepburn, T., Kilbey, S. M. & Sarles, S. A. Reversible, voltage-activated formation of biomimetic membranes between triblock copolymer-coated aqueous droplets in good solvents. Soft Matter 12, 5096–5109 (2016).

43. 43.

Lal, K., Tripathi, N. & Dubey, G. P. Densities, viscosities, and refractive indices of binary liquid mixtures of hexane, decane, hexadecane, and squalane with benzene at 298.15 K. J. Chem. Eng. Data 45, 961–964 (2000).

44. 44.

McIntosh, T., Simon, S. & MacDonald, R. The organization of n-alkanes in lipid bilayers. Biochim Biophys. Acta Biomembr. 597, 445–463 (1980).

45. 45.

Gross, L. C., Heron, A. J., Baca, S. C. & Wallace, M. I. Determining membrane capacitance by dynamic control of droplet interface bilayer area. Langmuir 27, 14335–14342 (2011).

46. 46.

Gentet, L. J., Stuart, G. J. & Clements, J. D. Direct measurement of specific membrane capacitance in neurons. Biophys. J. 79, 314–320 (2000).

47. 47.

Requena, J. & Haydon, D. The Lippmann equation and the characterization of black lipid films. J. Colloid Interf. Sci. 51, 315–327 (1975).

48. 48.

Jadidi, T., Seyyed-Allaei, H., Tabar, M. & Mashaghi, A. Poisson’s ratio and Young’s modulus of lipid bilayers in different phases. Front. Bioeng. Biotechnol. 2, 8 (2014).

49. 49.

Wang, D. et al. Hysteresis charges in the dynamic enrichment and depletion of ions in single conical nanopores. Chem. Electro Chem. 5, 3089–3095 (2018).

50. 50.

Wang, D. et al. Physical origin of dynamic ion transport features through single conical nanopores at different bias frequencies. Chem. Sci. 5, 1827–1832 (2014).

51. 51.

Hodgkin, A. L. & Huxley, A. F. A quantitative description of membrane current and its application to conduction and excitation in nerve. J. Physiol. 117, 500–544 (1952).

52. 52.

Najem, J. S., Rowe, I., Anishkin, A., Leo, D. J. & Sukharev, S. The voltage-dependence of MscL has dipolar and dielectric contributions and is governed by local intramembrane electric field. Sci. Rep. 8, 13607 (2018).

53. 53.

Jackman, S. L. & Regehr, W. G. The mechanisms and functions of synaptic facilitation. Neuron 94, 447–464 (2017).

54. 54.

Fortune, E. S. & Rose, G. J. Short-term synaptic plasticity as a temporal filter. Trends Neurosci. 24, 381–385 (2001).

55. 55.

Galisultanov, A., Le Moal, P., Bourbon, G. & Walter, V. Squeeze film damping and stiffening in circular CMUT with air-filled cavity: influence of the lateral venting boundary conditions and the bias voltage. Sens. Actuators A-Phys. 266, 15–23 (2017).

56. 56.

Pershin, Y. V. & Di Ventra, M. Memcapacitive neural networks. Electron. Lett. 50, 141–143 (2014).

57. 57.

Villar, G., Graham, A. D. & Bayley, H. A tissue-like printed material. Science 340, 48–52 (2013).

## Acknowledgements

Financial support was provided by the National Science Foundation Grant NSF ECCS-1631472. A portion of this research was conducted at the Center for Nanophase Materials Sciences, which is a DOE Office of Science User Facility. The graphics in Figs. 1, 5 and Supplementary Fig. 1 were modified from Servier Medical Art (http://smart.servier.com), licensed under a Creative Common Attribution 3.0 Generic License (https://creativecommons.org/licenses/by/3.0/). This manuscript has been authored by UT-Battelle, LLC, under Contract No. DE-AC0500OR22725 with the U.S. Department of Energy. The United States Government retains and the publisher, by accepting the article for publication, acknowledges that the United States Government retains a non-exclusive, paid-up, irrevocable, world-wide license to publish or reproduce the published form of this manuscript, or allow others to do so, for the United States Government purposes.

## Author information

Authors

### Contributions

J.S.N., S.A.S., R.S.W. and C.P.C. designed experiments; J.S.N. performed experiments with input from S.A.S., R.S.W., G.J.T. and C.P.C.; J.S.N. analyzed data with input from S.A.S., R.S.W., M.S.H. and C.P.C.; J.S.N. and M.S.H. developed mathematical models with input from R.S.W., S.A.S. and C.P.C.; M.S.H. performed the data fitting and model simulations with inputs from J.S.N., R.S.W., R.J.W. and G.S.R.; J.S.N., M.S.H., S.A.S., R.S.W. and C.P.C. wrote the paper; J.S.N. prepared figures and videos; J.S.N. and M.S.H. prepared Supplementary Information; J.S.N., R.S.W., S.A.S. and C.P.C conceived the concept; S.A.S. and C.P.C. managed and supervised the project. All discussed the results and commented on the manuscript at all stages.

### Corresponding authors

Correspondence to Stephen A. Sarles or C. Patrick Collier.

## Ethics declarations

### Competing interests

The authors declare no competing interests.

Peer review information: Nature Communications thanks Paschalis Gkoupidenis and the other anonymous reviewer(s) for their contribution to the peer review of this work. Peer reviewer reports are available.

Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

## Rights and permissions

Reprints and Permissions

Najem, J.S., Hasan, M.S., Williams, R.S. et al. Dynamical nonlinear memory capacitance in biomimetic membranes. Nat Commun 10, 3239 (2019). https://doi.org/10.1038/s41467-019-11223-8

• Accepted:

• Published:

• ### Characterizing the Structure and Interactions of Model Lipid Membranes Using Electrophysiology

• Joyce El-Beyrouthy
•  & Eric Freeman

Membranes (2021)

• ### Droplet-Based Membranous Soft Materials

• Michelle M. Makhoul-Mansour
•  & Eric C. Freeman

Langmuir (2021)

• ### Memristive synapses with high reproducibility for flexible neuromorphic networks based on biological nanocomposites

• Jun Ge
• , Dongyuan Li
• , Changqiao Huang
• , Xuanbo Zhao
• , Jieli Qin
• , Huanyu Liu
• , Weiyong Ye
• , Wenchao Xu
• , Zhiyu Liu
•  & Shusheng Pan

Nanoscale (2020)

• ### Instantaneous tension measurements in droplet interface bilayers using an inexpensive, integrated pendant drop camera

• Justin Rofeh
•  & Luke Theogarajan

Soft Matter (2020)

• ### An Artificial Optoelectronic Synapse Based on a Photoelectric Memcapacitor

• Lei Zhao
• , Zhen Fan
• , Shengliang Cheng
• , Lanqing Hong
• , Yongqiang Li
• , Guo Tian
• , Deyang Chen
• , Zhipeng Hou
• , Minghui Qin
• , Min Zeng
• , Xubing Lu
• , Guofu Zhou
• , Xingsen Gao
•  & Jun‐Ming Liu