Free-electron lasers (FELs) in the extreme ultraviolet (XUV) and X-ray regime opened up the possibility for experiments at high power densities, in particular allowing for fluence-dependent absorption and scattering experiments to reveal non-linear light–matter interactions at ever shorter wavelengths. Findings of such non-linear effects are met with tremendous interest, but prove difficult to understand and model due to the inherent shot-to-shot fluctuations in photon intensity and the often structured, non-Gaussian spatial intensity profile of a focused FEL beam. Presently, the focused beam is characterized and optimized separately from the actual experiment. Here, we present the simultaneous measurement of XUV diffraction signals from solid samples in tandem with the corresponding single-shot spatial fluence distribution on the actual sample. Our in situ characterization scheme enables direct monitoring of the sample illumination, providing a basis to optimize and quantitatively understand FEL experiments.
The development of free-electron lasers for the extreme ultraviolet (XUV) and X-ray regime has been one of the major leaps in photon-based science in the last few decades. It enabled key advances in the study of ultrafast dynamics of excitations in matter with a unique combination of coherent femtosecond pulses, and ultrahigh fluences up to several J cm−2 for XUV radiation, and several kJ cm−2 in the hard X-ray regime1,2. In recent years, observations of non-linear effects in solids such as wave mixing3,4, stimulated emission5,6,7, and absorption saturation8 have been reported. Conducting such experiments requires sophisticated control of the sample illumination. This includes the in situ control of the focus position and, possibly, the precise alignment of several free-electron laser (FEL) beams. After the experiment, an exact knowledge of the number of photons per unit time and area on the sample is crucial to interpret the measurements.
A number of well-established techniques exist to estimate these pivotal parameters. Gas monitor detectors are able to measure the total photon number in a single, few-femtosecond pulse9, but cannot account for the intensity distribution within the focal spot on the sample. This distribution is typically measured separately from the actual experiment using wave-front sensing10,11,12, ablative imprints13,14, or by detecting the transmitted intensity through a small aperture or behind a sharp knife-edge scanned across the beam in the sample plane2,15. These approaches are highly invasive and cannot be performed in tandem with the majority of FEL experiments. They are in particular incompatible with all scattering experiments in the forward direction and cannot account for the finite acceptance of a sample smaller than the beam size or for the beam position on a larger and potentially inhomogeneous sample. This leads to significant uncertainties, especially in diffract-and-destroy experiments, where a new sample is aligned after every single shot16,17,18.
In this work, we demonstrate the simultaneous measurement of the spatial fluence distribution on the sample in conjunction with the diffraction signal from a solid sample in a single-shot XUV FEL experiment. Our measurement scheme is derived from work on monolithically integrated gratings on carrier membranes19 and from the theoretical treatment of zone-plate diffraction under off-axis illumination20. Via our integrated diffraction monitor design, we are able to map the incident photon distribution on the sample to the detector plane. There, the illumination is recorded simultaneously with the sample’s scattering signal. This allows a precise control of the sample position during the experiment and yields reliable information on the sample illumination that is crucial for the interpretation of the data recorded.
Role of the fluence estimate in non-linear experiments
We demonstrate the importance of a precise fluence measurement for the interpretation of non-linear effects in Fig. 1. Here, we simulate a strongly focused, non-Gaussian FEL beam and consider three different estimates of the spatial fluence distribution f in the sample plane (ξ, η). The distributions represent, respectively, an accurate measurement (Fig. 1a), a blurred, low-resolution estimate as is typically the result of an aperture scan (Fig. 1b) and a constant estimate, where the shot energy is distributed uniformly over a certain area (Fig. 1c). The fluence histograms vary drastically for the different estimates, as shown in Fig. 1d. For each fluence distribution, we calculate the signal levels assuming a linear, power-law, or saturating fluence dependency (Fig. 1e–g, respectively). These non-linear relations occur for example in two-photon absorption or saturable absorption experiments. It is evident that, except for the linear case, an inaccurate fluence assumption obfuscates some or all of the characteristic parameters of the effect under study. Thus, a correct interpretation of fluence-dependent measurements will only be possible with an accurate, in situ characterization of the incident photon distribution on the sample on a shot-by-shot basis.
We consider an FEL diffraction experiment that detects scattered radiation as a function of momentum transfer q on a two-dimensional pixelated detector, as shown in Fig. 2. Note that this geometry also includes standard spectroscopy of the photon beam, where the beam at a selected momentum transfer (such as q = 0) is detected as a function of wavelength. In material and life sciences, thin membranes of Si3N4, Si, or polymers are commonly used to administer samples to the FEL beam. We equip these membranes with a grating structure, that gives rise to an additional scattering signal at a selected detector position19. The key idea of this work is to design the gratings such that each point on the sample surface diffracts the incoming light to a separate position on the detector while preserving the spatial relationship of the originating sample points. Figure 3 sketches the basic idea of our concept as a step-wise evolution from regular, to segmented, and finally to the spatially resolving gratings we discuss here.
We start with the following sinusoidal transmission function for a regular grating21:
Here, ξ and η are spatial coordinates in the sample plane, while p and φ are the grating period and orientation angle, respectively. They are given by the position (x, y, zdet) of the grating’s first diffraction order in the detector plane:
We turn φ and p into functions of the sample coordinates by setting
When inserted into Eq. (1), the result is a grating, the pitch and orientation of which varies continuously and that diffracts an image of its own illumination function, magnified by the dimensionless parameter m and centered at (x0, y0), to the detector. We note that the thereby obtained structures constitute segments of Fresnel zone plates (Supplementary Note 1).
where w0 is the beam’s waist size on the sample.
In simulations with Gaussian beams, we observe that the following condition must simultaneously be satisfied:
This relation enforces that the illumination does not change drastically within a small number of grating periods, which would lead to errors in the diffracted fluence maps (see Supplementary Notes 1 and 2 for a detailed discussion).
We present a single-shot XUV FEL diffraction pattern obtained in this fashion in Fig. 4a. The whole diffraction pattern consists of the ring-shaped primary sample signal (Methods) and the grating’s positive and negative diffraction orders. Note that this particular experiment investigates the non-linear breakdown of the primary sample signal at high XUV fluences22. Under these special circumstances, the measured intensities of both signal contributions are not well matched.
The extracted map (Fig. 4b) reveals a complex focal spot with a bright central area and several side lobes of considerable intensity. Its brightest feature has a full width at half maximum (FWHM) of 3.9 μm and aggregates 58% of the shot energy. The recorded FEL single shot has a moderate pulse energy of 11 μJ. This corresponds to a peak fluence of 40 J cm−2, which is well within the regime of previously reported non-linear XUV light–matter interactions5,8,23. Additionally, the beam’s smallest features (1.9 µm FWHM) are clearly resolved by our grating monitor. The whole spatial distribution is in very good agreement with the independently obtained data for a different single shot via a Hartmann wave-front sensor measurement, shown in Fig. 4c. Both measurements are furthermore consistent with the atomic force microscopy image of a single-shot damage crater in the sample substrate, shown in Fig. 4d. The line scans in Fig. 4e further demonstrate that the relative intensities measured by our grating monitors agree well with the wave-front sensor and damage crater data. Deviations between the three independent measurements are due to uncertainties associated with each technique (e.g., melting and redeposition in the damage crater, choice of numerical propagation parameters for wave-front sensor image, wavelength, and distance-scaling of the diffraction image) and the fact that they originate from different FEL shots.
Figure 5 displays a series of spatial fluence distributions, recorded at various positions along the beam propagation axis. In order to record the diffraction signals (Fig. 5a) without risk of destroying the sample with a particularly high-powered single shot—as might occur due to random intensity fluctuations inherent to the FEL source—we accumulate 2000 strongly attenuated shots per image. Thus, a perfect agreement with the wave-front sensor data (Fig. 5b) cannot be expected since the latter is extrapolated from a single-shot measurement. In particular, the accumulated images are blurred due to spatial jitter, that is, small, random changes of the beam pointing on a shot-to-shot basis. We are able to model the blurred, accumulated image at z = 0 (Fig. 5a, center) by applying a Gaussian filter to a destructive single-shot diffraction image (not shown), recorded at the same position. From this, we estimate the amount of spatial jitter in this particular case to be 3.5 μm (FWHM) in the horizontal, and 1.9 μm (FWHM) in the vertical direction. This is a significant fraction of the brightest feature’s spatial extent of 3.9 μm. It is obvious, that—in addition to mapping the internal structure of the focus—the access to the spatial jitter of the beam on the sample on a single-shot basis is extremely valuable. This applies particularly to laterally inhomogeneous samples with spatially varying material composition, including particles sparsely dispersed on a membrane.
Throughout the series, grating monitor and wave-front sensor data generally agree well. As discussed, the principal cause for the differences to the single-shot wave-front measurement is spatial jitter of the FEL beam. Note that the fluence distribution changes substantially within a few millimeters along the beam axis. This is due to the finite size of the optical elements that act as limiting apertures and introduce diffraction artifacts into the beam. We remark that our in situ fluence-mapping approach can easily be used to track and optimize the sample position with respect to a focus both in the transverse direction as well as along the beam axis, e.g., when aligning samples for an experiment.
The attainable spatial resolution of our approach is closely linked to the manufacturing process. We use focused ion beam (FIB) milling to directly pattern the grating structures into the sample membrane (see Methods section for details on the manufacturing process). This fast and flexible method is capable of producing structure sizes down to a few tens of nanometers with low aspect ratios. As a rule of thumb, the necessary structure size (i.e., the grating half-pitch) to map a particular focal spot is about one-tenth of the spot size. Note that Eq. (7) enforces this condition (Supplementary Note 2 and Supplementary Fig. 1). Given the milling resolution of the FIB process, our approach is directly capable of mapping sub-micrometer focal spots in the XUV and soft X-ray regime.
Moving toward even shorter wavelengths and into the hard X-ray regime, the absorption contrast for most materials—and thereby the grating efficiency—diminishes. This necessitates higher aspect ratios for the grating structures and thus a more challenging manufacturing process. Furthermore, the achievable focal spots of the FEL beam are considerably smaller, extending into the sub-100 nm region2,15. Consequentially, smaller grating structures are necessary to satisfy Eq. (7).
Due to their close relationship to our grating monitors, it seems reasonable to consider recent progresses in hard X-ray zone-plate manufacturing for the discussion of these issues. Zone plates with 15 nm outer zone width have successfully been manufactured for hard X-ray radiation and are used in experiments with 9 keV photon energy24. With such manufacturing capabilities, it is feasible to directly transfer our concept to the hard X-ray regime and focal spot sizes on the order of 100 nm. Additionally, our concept does not require high diffraction efficiencies and aspect ratios can accordingly be smaller than for a zone plate. This makes it possible to utilize even smaller structures, and achieve sub-100 nm resolution. However, the complex manufacturing process might—at the current technological state—prohibit the time- and cost-efficient fabrication of a large number of samples for destructive studies. The actual limit will of course depend on the specific experiment, including photon energy, sample size and thickness, available detector space, and the experiment geometry.
The low absorption of hard X-ray radiation in most of the conceivable grating materials is greatly beneficial when transparent beam monitors are considered. In such cases, our grating concept could provide permanent and reliable in situ feedback of the beam position and spatial structure at critical beam-line positions, such as split-and-delay units25,26 or intermediate focus stages15. This is further encouraged by the fact that spatial constraints in the experimental setup apply to a much lesser degree since high-vacuum conditions are usually not required. We note that no computational treatment of the measured fluence distributions is necessary. This makes the concept suitable for live monitoring, even at very high repetition rates.
Our fluence-mapping approach is a unique tool for true in situ, single-shot-capable monitoring of the fine structure of the sample illumination in transmission-type scattering experiments. It is, to our knowledge, the only approach that allows for a simultaneous, non-invasive mapping of the fluence distribution on the sample together with a scattering signal of interest. The approach provides an instantaneous online signal, which can be interpreted without any further computation, and can thus be used as instant feedback to align the upstream optical system. In the study of fluence-dependent phenomena, it provides crucial information for the correct interpretation of the data. The position and magnification of the photon-fluence map on the detector is, within the discussed constraints and the limits of the particular manufacturing process, freely selectable. Furthermore, the derivation of the grating formula can easily be adapted for diffraction experiments in reflection geometry. This makes our fluence-mapping approach compatible with a large variety of experiments and samples. Given these features, we expect this approach to become a valuable tool for alignment and optimization, and in particular for the study of non-linear light–matter interaction in the XUV and X-ray regime.
We perform small-angle scattering in transmission geometry at the FERMI@Elettra FEL source, using the DiProI end-station27. Focusing is provided via a bendable Kirkpatrik–Baetz optics28. A Princeton Instruments PI-MTE in-vacuum charge-coupled device (CCD) camera (2048 × 2048 pixel, 13.5 μm edge length) detects the scattered radiation 75–150 mm downstream of the sample. For the data in Fig. 4a, the sample–CCD distance is 75 mm. A cross-shaped beam-stop in front of the camera blocks the intense radiation in the forward direction and potential membrane edge scattering. We subtract dark images to flatten the image background. In the single-shot image, we manually remove a linear background that is due to a read-out artifact in the CCD wells that are read after the highest intensity occurs and de-noise the image by applying a Gaussian filter with 2 px width. The incident X-ray pulses are tuned to a wavelength of 20.8 nm (59.6 eV) with single-shot pulse energies ranging from 0.5 to 60 μJ. For accumulating measurements at a repetition rate of 10 Hz, solid-state filters and a gas absorber reduce the pulse energy to a range between 20 and 80 nJ. The Hartmann WFS—manufactured by Imagine Optique—is equipped with a 72 × 72 pinhole grid (pinhole diameter 60 µm, pitch 180 µm) and has a nominal accuracy of λ/100.
The samples consist of Si3N4 membranes of 30 nm thickness with 30–200 μm edge length. For the purpose of other experiments, a magnetic Co/Pt multi-layer is deposited on the membranes by DC magnetron sputtering. In the experiments reported here, this sample layer is in a labyrinth-like domain state with magnetization vectors parallel or anti-parallel to the FEL beam axis. At the selected photon wavelength, these domains give rise to a ring-shaped scattering signal on the CCD detector via the X-ray magnetic circular dichroism effect. We use a focused Ga+ ion beam (FIB) to mill gratings directly into the Si3N4 membrane at 30 kV acceleration voltage and 93 pA beam current. For the milling process, the gratings are generated on a grid of 3500 × 3500 points with x0 = y0 = 9.5 mm, λ = 20.8 nm, z = 150 mm, and m = 80. In this particular case, milling the 35 × 35 μm grating with a nominal topographic amplitude of 2 nm takes 60 s.
The data that support the findings of this study are available from the corresponding authors upon reasonable request.
Feldhaus, J., Arthur, J. & Hastings, J. B. X-ray free-electron lasers. J. Phys. B At. Mol. Opt. Phys. 38, 799–819 (2005).
Yumoto, H. et al. Focusing of X-ray free-electron laser pulses with reflective optics. Nat. Photonics 7, 43–47 (2012).
Bencivenga, F. et al. Four-wave mixing experiments with extreme ultraviolet transient gratings. Nature 520, 205–208 (2015).
Glover, T. E. et al. X-ray and optical wave mixing. Nature 488, 603–608 (2012).
Beye, M. et al. Stimulated X-ray emission for materials science. Nature 501, 191–194 (2013).
Stöhr, J. & Scherz, A. Creation of X-ray transparency of matter by stimulated elastic forward scattering. Phys. Rev. Lett. 115, 107402 (2015).
Yoneda, H. et al. Atomic inner-shell laser at 1.5-Å wavelength pumped by an X-ray free-electron laser. Nature 524, 446–449 (2015).
Nagler, B. et al. Turning solid aluminium transparent by intense soft X-ray photoionization. Nat. Phys. 5, 693–696 (2009).
Tiedtke, K. et al. Gas detectors for X-ray lasers. J. Appl. Phys. 103, 094511 (2008).
Keitel, B. et al. Hartmann wavefront sensors and their application at FLASH. J. Synchrotron Radiat. 23, 43–49 (2016).
Le Pape, S. et al. Electromagnetic-field distribution measurements in the soft X-ray range: full characterization of a soft X-ray laser beam. Phys. Rev. Lett. 88, 183901 (2002).
Schäfer, B. & Mann, K. Determination of beam parameters and coherence properties of laser radiation by use of an extended Hartmann-Shack wave-front sensor. Appl. Opt. 41, 2809–2817 (2002).
Chalupsky, J. et al. Spot size characterization of focused non-Gaussian X-ray laser beams. Opt. Express 18, 27836 (2010).
Nelson, A. J. et al. Soft X-ray free electron laser microfocus for exploring matter under extreme conditions. Opt. Express 17, 18271 (2009).
Mimura, H. et al. Generation of 1020 W cm−2 hard X-ray laser pulses with two-stage reflective focusing system. Nat. Commun. 5, 3539 (2014).
Vartanyants, I. A. et al. Coherence properties of individual femtosecond pulses of an X-ray free-electron laser. Phys. Rev. Lett. 107, 144801 (2011).
Chapman, H. et al. Femtosecond diffractive imaging with a soft-X-ray free-electron laser. Nat. Phys. 2, 839–843 (2006).
Seibert, M. M. et al. Single mimivirus particles intercepted and imaged with an X-ray laser. Nature 470, 78–81 (2011).
Schneider, M., Günther, C. M., von Korff Schmising, C., Pfau, B. & Eisebitt, S. Curved gratings as an integrated photon fluence monitor in X-ray transmission scattering experiments. Opt. Express 24, 13091 (2016).
Janicijevic, L. Diffraction of Gaussian beams through different types of zone plates. J. Opt. 18, 23–42 (1987).
Goodman, J. W. Introduction to Fourier Optics 3rd edn (Roberts & Company Publishers, Englewood, 2007).
Müller, L. et al. Breakdown of the X-ray resonant magnetic scattering signal during intense pulses of extreme ultraviolet free-electron-laser radiation. Phys. Rev. Lett. 110, 234801 (2013).
Mincigrucci, R. et al. Role of the ionization potential in nonequilibrium metals driven to absorption saturation. Phys. Rev. E 92, 011101 (2015).
Mohacsi, I. et al. Interlaced zone plate optics for hard X-ray imaging in the 10 nm range. Sci. Rep. https://doi.org/10.1038/srep43624 (2017).
Roseker, W. et al. Development of a hard X-ray delay line for X-ray photon correlation spectroscopy and jitter-free pump–probe experiments at X-ray free-electron laser sources. J. Synchrotron Radiat. 18, 481–491 (2011).
Osaka, T. et al. Wavelength-tunable split-and-delay optical system for hard X-ray free-electron lasers. Opt. Express 24, 9187 (2016).
Capotondi, F. et al. Invited article: coherent imaging using seeded free-electron laser pulses with variable polarization: first results and research opportunities. Rev. Sci. Instrum. 84, 051301 (2013).
Raimondi, L. et al. Microfocusing of the FERMI@Elettra FEL beam with a K–B active optics system: spot size predictions by application of the WISE code. Nucl. Instrum. Methods Phys. Res. Sect. A 710, 131–138 (2013).
We thank the FERMI accelerator and laser teams for their great support during the experiments.
The authors declare no competing financial interests.
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Schneider, M., Günther, C.M., Pfau, B. et al. In situ single-shot diffractive fluence mapping for X-ray free-electron laser pulses. Nat Commun 9, 214 (2018). https://doi.org/10.1038/s41467-017-02567-0