A main obstacle in the rational development of heterogeneous catalysts is the difficulty in identifying active sites. Here we show metal/oxide interfacial sites are highly active for the oxidation of benzyl alcohol and other industrially important primary alcohols on a range of metals and oxides combinations. Scanning tunnelling microscopy together with density functional theory calculations on FeO/Pt(111) reveals that benzyl alcohol enriches preferentially at the oxygen-terminated FeO/Pt(111) interface and undergoes readily O–H and C–H dissociations with the aid of interfacial oxygen, which is also validated in the model study of Cu2O/Ag(111). We demonstrate that the interfacial effects are independent of metal or oxide sizes and the way by which the interfaces were constructed. It inspires us to inversely support nano-oxides on micro-metals to make the structure more stable against sintering while the number of active sites is not sacrificed. The catalyst lifetime, by taking the inverse design, is thereby significantly prolonged.
Aldehydes and ketones are widely used as solvents, polymer precursors, high value-added components in perfumes and intermediates of dyes as well as pharmaceuticals1,2. Many of them are synthesized by stoichiometric oxidation of alcohols using expensive and toxic oxidants such as chromate or permanganate1. Gas-phase selective oxidation of alcohols using oxygen or air as the oxidant represents an industrially feasible and environmentally benign protocol, which produces aldehydes and ketones in a solvent-free, continuous manner3,4. Although a number of heterogeneous catalysts, such as supported Cu (ref. 3), Ag (ref. 5), Au (ref. 6) and bimetallic particles (ref. 6), have been developed for this process, the nature of the active sites are still not fully understood and many of the catalysts suffered fast degradation in activity.
The pivotal role of metal/oxide interfaces has been recognized in several catalytic processes. For example, Cu/ZnO/Al2O3 and Cu/CeOx are highly active for methanol synthesis7; ZnPd/ZnO leads to high CO2 selectivity in methanol steam reforming8; Cu/CeOx (ref. 9), Au/CeOx (ref. 10), Pt/CeOx (ref. 11) and PtCox/Co3O4 (ref. 12) exhibit improved efficiency for water-gas shift reaction; Pt/FeOx (ref. 13), Au/TiOx (ref. 14) and Au/FeOx (ref. 15) boost CO (preferential) oxidation. In the context of alcohol oxidation, Abad et al.16,17 observed high and general activity of Au/CeO2 under solvent-free conditions as well as in organic solvents. Their study established a linear correlation between the activity and the total number of external gold atoms, as well as the surface coverage of the cerium support. They proposed that the cerium support stabilize positive gold species which act as Lewis-acid sites to adsorb alcohols, and also facilitate oxygen activation through oxygen vacancies to promote the re-oxidation of preformed metal hydrides. Bauer et al.18 developed an efficient Au-CuOx core–shell catalyst for aerobic oxidation of ethanol. They presumed that the close contact between the metal core and oxide shell generates the active sites. Further mechanistic explanation was attempted by a recent study by Redina et al. They suggested the strong interaction between metallic Au and the isolated Cu2+ ions account for the high activity of the Au–Cu catalysts19.
Here, we report gas-phase selective oxidation of primary alcohols over a series of metal/oxide interfaces with greatly enhanced performance. The underlying mechanism of the promoted activity at the interfacial sites is investigated by scanning tunnelling microscopy (STM) measurements on both FeO/Pt(111) and Cu2O/Ag(111) model catalysts together with theoretical studies. Several common features of different metal/oxide systems are further disclosed after analysing the overall reaction carefully by density functional theory (DFT) calculations. On the basis of these understanding, we conceive an anti-sintering catalyst and extend the concept to a practical monolithic catalytic system based on TMO/Ag/Cu-gauze (transition metal oxide) structure.
STM and DFT studies on FeO/Pt(111) model catalyst
We started our investigation on the gas-phase oxidation of benzyl alcohol over Pt, FeO and Pt/FeO colloidal nanoparticles. Individual Pt or FeO shows much lower conversion (<15%) than Pt/FeO nanocomposite (∼86%) at a temperature from 230 to 270 °C (Supplementary Fig. 1A–C). The apparent activation energy of benzyl alcohol oxidation decreases from 91 kJ mol−1 on FeO and 102 kJ mol−1 on Pt to 64 kJ mol−1 on Pt/FeO nanocomposite (Supplementary Fig. 1D). Encouraged by this interesting observation, we constructed FeO islands on the Pt(111) surface, termed as FeO/Pt(111), to study the benzaldehyde formation using STM. The atomic structure of as-prepared FeO islands is magnified in Supplementary Fig. 2. The curvy shape of step edges of FeO islands with periodic indentation is a typical character for the Fe-terminated step edges of FeO on Pt(111)20 (denoted as Fe-FeO/Pt(111)). When exposed to O2, the Fe-terminated step edges evolve into O-terminated step edges (denoted as O-FeO/Pt(111), Fig. 1a) by O2 dissociation at the coordinatively-unsaturated Fe sites. These steps were found to be the most stable step termination when FeO/Pt(111) was exposed to O2 at room temperature or above21. The evolution of the oxidation state of iron was investigated by X-ray photoelectron spectra (XPS). Upon oxygen adsorption, two-coordinated ferrous sites at the steps of FeO become three-coordinated, as is the case for Fe atoms inside the FeO nanostructures. Thus, FeO should remain the Fe2+ state with oxygen attached to the step edges. Accordingly, in the XPS spectra (Supplementary Fig. 3), Fe 2p3/2 peak from O-FeO/Pt(111) (709.3 eV) is only slightly more positive than that of Fe-FeO/Pt(111) (708.6 eV), indicating the Fe2+ state of FeO nanostructures, regardless of their step termination. Fe3+ on Pt(111) should give a Fe 2p3/2 peak at above 710 eV, as shown in the previous study22. Supplementary Figure 4 shows the surface of O-FeO/Pt(111) after an exposure of ∼0.4 L (1 L=1.0 × 10-6 Torr s) benzyl alcohol at room temperature. The adsorbed species appear to be bright spots on both the Pt(111) surface and the edges of O-FeO islands. Notably, the density of bright spots appears to be more enriched at the step edges of O-FeO islands with smaller size, as marked by circles in Supplementary Fig. 4A. The density of bright spots increases with the increasing exposure of benzyl alcohol (1 L, Fig. 1b). From image analysis, the spot density at the interface corresponds to 0.132 molecule per O/Fe site, while on the Pt(111) surface the number is 0.0096 molecule per Pt site (see detailed analyses in Supplementary Fig. 5). The interfacial adsorption of benzyl alcohol is further compared at Fe-terminated steps (Fig. 1c) and O-terminated steps (Fig. 1d). Benzyl alcohol could stably adsorb at O-FeO steps after the annealing at 350 K (Fig. 1b), whereas at Fe-FeO steps, benzyl alcohol could adsorb at 300 K, but desorb at 350 K (Supplementary Fig. 6). In STM images, benzyl alcohol appears to have a higher apparent height at Fe-FeO steps than at O-FeO steps (Fig. 1e). The species with lower apparent height at the O-FeO steps could be assigned as dissociatively adsorbed benzyl alcohol species, which could be distinguished from molecularly adsorbed benzyl alcohol because of their different apparent heights and desorption temperatures. Due to the dissociation of O–H bond, oxygen tends to withdraw electrons from neighboring atoms, rendering a lowered apparent height of the adsorbate in STM topography. Such character has also been used to distinguish molecular or dissociated alcohol species previously23. The facile deprotonation of alcohols on FeO/Pt(111) has been shown in IRAS and TPD studies by Kim et al.24 A broad water desorption peak at between 200 and 400 K, indicating the facile deprotonation of alcohols, was observed, which does not occur on Pt(111). Accordingly, our STM images suggest that H from benzyl alcohol reacts with O at the edge of FeO to form water, which desorbs at above 200 K. Indeed, under-coordinated oxygen at the edge of FeO is very reactive that, upon the flash to 350 K, part of the edges of FeO islands are reduced (Fig. 1).
To provide insight into the mechanism of benzaldehyde formation, first-principles calculations were carried out on both the Pt(111) surface and the FeO/Pt(111) interface. The free energy profiles of benzaldehyde formation on Pt(111) are illustrated in Supplementary Fig. 7 and discussed in detail in the Supplementary Discussion. The Fe-terminated FeO/Pt(111) interface was constructed by placing a thin FeO ribbon on Pt(111) (Supplementary Fig. 8)21. In our model, the FeO/Pt ribbon can maintain its hexagonal layer configuration during the optimization calculation, indicating that the FeO layer is reasonably stable. The exposed coordinatively-unsaturated Fe sites show a strong oxygen adsorption ability (−1.27 eV) and could readily be oxidized via a low oxygen dissociation barrier (0.34 eV, Supplementary Fig. 9), resulting in the O-FeO/Pt(111) interface (Fig. 2a). This is in accordance with our STM observation and previous results21. On the O-FeO/Pt(111) interface, the hydrogen of hydroxyl in adsorbed benzyl alcohol forms a hydrogen bond with a terminated oxygen (Fig. 2b; Supplementary Fig. 10A). The adsorption of benzyl alcohol is exothermic by 3.62 eV, slightly stronger than that on the Fe-FeO/Pt(111) interface (Supplementary Fig. 11, 3.38 eV). Interestingly, with the aid of the interface oxygen, the O-H bond activation barriers are significantly diminished to below 0.1 eV for both reaction pathways shown in Supplementary Table 1. In pathway 1 (Supplementary Fig. 10B–D), the subsequent C–H bond cleavage can also occur facilely via a low reaction barrier (0.14 eV) with 1.29 eV heat releasing; while in pathway 2 (Supplementary Fig. 10E–H), the activation of C–H bond cleavage is much more difficult (0.40 eV). Clearly, pathway 1 is favoured for the benzaldehyde formation due to a lower overall activation barrier. After the O–H and C–H dissociations, the O-FeO/Pt is converted to HO-FeO/Pt (Fig. 2c) and surface H atoms are produced. Water molecules are then formed through hydrogenating OH by the surface H atoms on the interface to restore the Fe-terminated FeO/Pt interface (Supplementary Fig. 12), completing the catalytic cycle. It is found that the overall activation energy of water formation is below 0.4 eV (Supplementary Table 2), which is not difficult to overcome under the experimental conditions.
By comparing the Pt(111) surface to the FeO/Pt interface, the following striking features can be seen: firstly, the benzyl alcohol adsorption is much stronger on the FeO/Pt interface, indicating that the benzyl alcohol coverage would be increased at the FeO/Pt interface, which coincides well with the STM results. Secondly, for the slow step of O–H bond breaking, the reaction barrier is significantly lower at the O-FeO/Pt(111) interface than on Pt(111) (0.05 eV versus 0.70 eV, Supplementary Fig. 13 and Supplementary Table 3). This is also evidenced by our STM study of the apparent heights of adsorbed species at the O-FeO/Pt(111) interface. It is clear that the strong hydrogen binding between the oxygen at the edge of FeO/Pt interface and the hydrogen of hydroxyl not only increases the adsorption of benzyl alcohol but also effectively weakens the O–H bond of benzyl alcohol, which results in a decrease of the activation barrier. Similar to the O–H bond breaking, the barrier of C–H scission on the interface is also considerably reduced comparing to Pt(111) (0.14 eV versus 0.42 eV), leading to the high overall activity.
Quantitative study on in situ formed PdCux/Cu2O catalyst
The interface-enhanced benzyl alcohol oxidation was quantitatively studied on PdCux/Cu2O interface which evolved from Pd-Cu alloy under reaction conditions. A series of monodisperse Pd-Cu alloys with tunable compositions (Supplementary Figs 14 and 15) were prepared by colloidal synthesis. Using pure Pd as a catalyst, benzyl alcohol conversion is 20% while the selectivity of undesired benzene is up to 9% (Supplementary Table 4, entry 1). However, after incorporating Cu into Pd nanoparticles, the catalyst performance is progressively enhanced (entries 2–7) with the increase of Cu:Pd molar ratio. Notably, with the Cu:Pd ratio above 5:1, the benzyl alcohol conversion and the benzaldehyde selectivity are increased to >93 and >97%, respectively (entries 5–7). Nevertheless, the benzyl alcohol conversion is as low as 21% when pure Cu was used (Supplementary Fig. 16, and entry 8). X-ray diffraction patterns of the used Pd-Cu alloy catalysts indicate that the fresh Pd-Cu alloy (Supplementary Fig. 17) is transformed into PdCux/Cu2O heterostructures (Fig. 3a), and the intensity of Cu2O phase increases along with the Cu:Pd molar ratio. XPS also shows the presence and monotonic increase of Cu+ over the used catalyst surface (Supplementary Figs 14 and 18). More importantly, we found that the benzyl alcohol conversion increased linearly at low surface Cu+ content, and then maintained with a further increase of surface Cu+ content (Fig. 3b). High-resolution transmission electron microscopic (HRTEM) images of PdCu7 catalysts before and after the catalytic reaction visualize the structural evolution from homogeneous alloy to the heterostructure of small Cu2O patches on PdCux particles (Fig. 3c,d; Supplementary Fig. 19). Additional control experiments were further performed, as shown in Supplementary Table 4. Pure Cu2O only delivers a benzyl alcohol conversion of 19% (entry 9). However, the benzyl alcohol conversion is enhanced to >90% (entries 10–13) by even physically mixing Cu2O with low active Pd, Pd3Cu, PdCu or PdCu3. These observations strongly support that the PdCux/Cu2O interface is the active sites for benzyl alcohol oxidation.
Validation of interfacial effects on Cu2O/Ag(111) catalyst
The metal/oxide interfacial effects on benzyl alcohol oxidation were also validated in inexpensive Ag/TMO system by STM and theoretical studies. We first investigated the benzyl alcohol adsorption at the interface of Cu2O/Ag(111) using STM. Supplementary Fig. 20A shows Cu2O islands of monolayer thickness dispersed on the Ag(111) substrate. The ordered honeycomb structure of Cu2O islands is depicted in Supplementary Fig. 20B, with all Cu atoms resolved as bright dots. The lattice spacing of Cu2O on Ag(111) is measured of 0.60 nm, same as that of Cu2O(111) on Cu(111)25. Supplementary Fig. 20C shows the typical topography of Cu2O/Ag(111) after the exposure of benzyl alcohol at 115 K. Benzyl alcohol molecules, appearing as bright spots, adsorb only at edges of Cu2O islands (Supplementary Fig. 20D). After the annealing at 300 K, adsorbed benzyl alcohol molecules desorb partially, accompanying the formation of new species at the Cu2O–Ag interface (Supplementary Fig. 20E and F). These new species exhibit a smaller apparent size than that of adsorbed benzyl alcohol, and could be attributed as phenol oxy intermediates (Supplementary Fig. 21). We further tested the adsorption and activation of benzyl alcohol at CuOx/Ag(111) interfaces (Supplementary Figs 22 and 23) by DFT calculations. The adsorption of benzyl alcohol is enhanced by 0.8 eV at CuOx/Ag interface in comparison with Ag(111) (−1.06 eV); and the barrier of O-H scission is largely diminished (below 0.1 eV), comparing the much higher barrier on Ag(111) (1.56 eV). The STM and DFT results demonstrate a similar role of Cu2O–Ag interface as FeO–Pt interface in enhancing the adsorption and activation of benzyl alcohol molecules26.
A common descriptor for catalytic activity
To further understand the promotion effect of the oxide/metal systems, the overall reactions were carefully analysed and some common features were obtained using DFT calculations. Firstly, the activation energy of O–H bond cleavage can be significantly decreased in the presence of boundary oxygen, while much higher barriers need to be overcome on metal substrates, including Pt, Pd and Ag surfaces (Supplementary Table 5). Secondly, the activation energies of C–H bond cleavage are in the range from 0.4 to 0.6 eV at the metal surfaces (Ag(111), Pd(111), Pt(111), see Supplementary Table 5), which should be readily overcome under the reaction conditions (over 500 K). Thirdly and perhaps more importantly, the suitable binding strength of oxygen at interfacial sites is found to be of significance to complete the overall catalytic cycle. On one hand, too weak binding strength of oxygen will make the interfacial sites inert for oxygen adsorption and dissociation. On the other hand, the oxygen vacancy formation (that is, hydroxyl removal in our work) will be difficult if the oxygen binding is too strong. Thus, it is crucial to balance the oxygen adsorption and its further removal at the interfacial sites. In the FeO/Pt system, the free energy changes of oxygen adsorption (1/2 O2+*→O*) and its vacancy formation (OH*+H* →H2O+2*) were calculated to be −0.47 and −0.76 eV, respectively, which are both favourable thermodynamically. The thermodynamics of the above two elementary steps were also calculated on other oxide/metal systems, as shown in Supplementary Fig. 24. Indeed, the oxygen binding strength and its removal have the similar features: the free energy changes of both reactions are all below zero, suggesting that the oxygen species are active for benzyl alcohol oxidation at the considered MOx/metal (M=Mn, Fe, Co, Ni, Cu; metal=Pt, Pd, Ag) interfaces. In addition, we also considered the systems of MgO/metal. The binding of oxygen is much stronger at the MgO/metal interfacial sites than other MOx/metal interfaces (Supplementary Fig. 24A). However, the removal of hydroxyl is hindered thermodynamically (Supplementary Fig. 24B), indicating that the overall catalytic cycle will be blocked at MgO/metal interfaces. Experimental results are in good agreement with theoretical prediction. As presented in Supplementary Table 6, the conversion of benzyl alcohol is as low as 12.7% even increasing the reaction temperature to 300 °C. These results suggest that a proper oxygen binding strength is crucial and may be considered as an energy descriptor for such systems.
The size independence of the interfacial effects
Since the metal–oxide interface has been identified as the active sites, we reason that the aerobic alcohol oxidation on the catalysts would be size insensitive. One would expect similarly high catalytic activity among the catalysts with different dimensions, on condition that sufficient interfacial sites have been constructed. To verify this inference, we designed three different forms of Ag/TMO interfaces including Ag–TMO nanocomposite, nano-Ag supported on micro-TMO, and nano-TMO supported on micro-Ag to demonstrate their equivalency (Supplementary Fig. 25). As shown in Fig. 4 and Supplementary Table 7, Ag–Cu2O nanocomposite (Supplementary Fig. 26) exhibits much better performance (Supplementary Table 7, entries 1–3) than pure nano-Ag (Supplementary Fig. 27) and nano-Cu2O (Supplementary Fig. 28). The apparent activation energies of benzyl alcohol oxidation decrease from 68 kJ mol−1 on nano-Ag and 87 kJ mol−1 on nano-Cu2O to 43 kJ mol−1 on Ag–Cu2O nanocomposite (Supplementary Table 8). Even over the physical mixtures of nano-Ag and other nano-TMO such as NiO, CoO, and Mn3O4 (Supplementary Fig. 25), benzyl alcohol conversions are still much higher than that over the pure nano-Ag or nano-TMO (Supplementary Table 7, entries 4–9). Similar to the nanocomposite, both nano-Ag/micro-TMO (Cu2O, NiO, Mn3O4 and CoO) and inverse nano-TMO/micro-Ag deliver higher benzyl alcohol conversion than individual metal or transition metal oxides (>90% versus <15%, Supplementary Table 7, entries 2 and 10–22). This suggests that the interfacial effects are independent of the size of each constituent. Furthermore, we compared quantitatively the activity of normal nano-metal/micro-oxide and inverse nano-oxide/micro-metal interface by taking the nano-Ag/micro-Mn3O4 and the inverse nano-Mn3O4/micro-Ag as a model. We investigated the catalytic performance of the two catalysts with different loadings of nano-Ag and nano-Mn3O4, respectively. The specific surface areas of as-prepared nano-Ag and nano-Mn3O4 were determined as 22 and 37 m2 g−1, respectively, by N2 physical adsorption method (Supplementary Table 9). As shown in Supplementary Fig. 29, the benzyl alcohol conversion increases linearly along with the loadings of nano-Ag or nano-Mn3O4 below 3 wt%, and the slopes are 26 and 42, respectively. The slope ratio (26/42) is almost equal to the specific surface area ratio (22/37), indicating the nearly equivalent catalytic activities at the Ag-Mn3O4 interface over the two catalysts.
One interesting observation in the Ag/TMO systems is that the physical mixtures of the nano-Ag and nano-TMO, such as Mn3O4, NiO and CoO, still exhibit enhanced activity over their parent components (Supplementary Table 7, entries 4–6). It probably arises from the in situ formed Ag-TMO interface via the close contact of each component. We therefore separately loaded both Ag and TMO on inert SiO2 support before mixing them. The inert SiO2 acts as a structural promoter that keeps Ag and TMO spatially isolated. The catalytic performance of these catalysts are summarized in Supplementary Table 10. The low benzyl alcohol conversion (typically below 35%) over ‘Ag/SiO2+TMO/SiO2’ mixtures indirectly validates our assumption that the promoted catalytic performance comes from the direct contact of the metal and the metal oxide. We further confirmed the formation of Ag-TMO interface by charactering the physically-mixed ‘Ag+NiO’ catalyst after use. Energy-dispersive X-ray spectroscopy elemental mapping of the spent catalyst shows the attachment of the Ag domain to the Ni domain (Supplementary Fig. 30A). The lattice fringes depicted in the corresponding HRTEM images (Supplementary Fig. 30B) demonstrate that the two crystal domains are chemically bonded together.
Inverse-interface design leading to more stable catalyst
Having understood the catalytic nature of gas-phase alcohol oxidation over metal/oxide systems, we realize that these insights might enable us to design better catalytic materials with long-term stability. Small metal nanoparticles supported on bulk metal oxides often suffer particle sintering in exothermic or high temperature catalytic processes, leading to fast deactivation of the catalysts27. Particular to gas-phase alcohol oxidation, the long-term stability still remains a challenging task3,4,5,6. The tendency of particle sintering is usually associated with the melting point of the material. It is worth mentioning two points here: (i) the bulk melting points of metal oxides are generally higher than metals; and (ii) the melting points of nanoparticles are size-dependent; the smaller the size is, the lower the melting point is28. In this context, the stability of the nano-metal/micro-oxide catalyst and the inverse counterpart (nano-oxide/micro-metal) must be drastically different, although their catalytic activities are comparable. Taking the Ag–Cu2O interface as an example, the benzyl alcohol conversion starts declining within 2 h over nano-Ag/micro-Cu2O, but it stays quite stable (>90%) for at least 230 h using the inverse nano-Cu2O/micro-Ag catalyst (Supplementary Fig. 31). Nano-Ag supported on micro-Cu2O showed serious particle sintering after the stability test, in sharp contrast to the almost unaffected size distribution of nano-Cu2O supported on micro-Ag (Supplementary Fig. 32). The long-term stability of the inverse catalyst design was also confirmed by nano-CoO/micro-Ag (Supplementary Fig. 33). In addition, the deactivated nano-Ag/micro-CoO can restore the initial activity (conversion: 91%; selectivity: 99%) simply by post-doping CoO nanoparticles on the surface to reconstruct sufficient Ag–CoO interface. This regeneration strategy is of great potential in recovering other thermally deactivated catalysts, such as three-way catalyst in catalytic converters and the catalyst for removing volatile organic compounds.
Selective oxidation of other primary alcohols
The effectiveness of metal-oxide interface in benzyl alcohol oxidation has been extended to straight-chain, benzylic and polynary (1,2-propanediol) alcohols (Table 1) using inverse nano-CoO/micro-Ag. 1-phenylethanol is oxidized to acetophenone at a high conversion of 97% at 270 °C, and the primary linear octanol alcohol (1-ol) conversion is 67%. Cyclohexanol is selectively oxidized to cyclohexanone (a key raw material for many useful chemicals, such as caprolactam for nylon 6 and adipic acid for nylon 66) at a conversion of 79% with a selectivity of 95% at 280 °C. Furthermore, alcohols containing two hydroxyl groups, such as 1,2-propylene glycol that is favourable to form hydroxylketone rather than methyl glyoxal, could also be selectively oxidized to the target product (methyl glyoxal) with a selectivity of 72% at a conversion of 94%.
Rational design of a practical monolithic catalyst
Guided by the interfacial effects revealed here, we designed a monolithic catalyst eligible for future industrial application, that is, Cu2O/Ag/Cu-gauze with three-dimensional open structures (Fig. 5). To realize the Ag–Cu2O interface on the commercially available Cu-gauze, a thin silver film was coated on the surface of Cu-gauze by silver mirror reaction29. Then the copper oxides were deposited on the Ag/Cu-gauze matrix. Scanning electron microscopic images show that the surface of Cu-gauze (Fig. 5a) is coated with Ag and Cu2O (Fig. 5b), and X-ray diffraction patterns also exhibit the characteristic peaks of Ag and Cu2O (Supplementary Fig. 34). The gas-phase selective oxidation of benzyl alcohol was subsequently conducted. Over the Cu2O/Ag/Cu-gauze, benzyl alcohol conversion is 95% at 300 °C and 91% at 260 °C. In contrast, the Ag/Cu-gauze and Cu2O/Cu-gauze show much lower benzyl alcohol conversions at the corresponding reaction temperature (Supplementary Fig. 35). Ex situ characterizations including X-ray diffraction, N2 physical adsorption, and XPS were performed on the monolithic catalyst during the course of on-stream running. As shown in Supplementary Figs 36–38, the phase compositions, surface areas, as well as the oxidation states of Cu and Ag in the spent catalyst stay almost unchanged compared with the fresh one. The outstanding structural stability of the monolithic catalyst leads to exceptionally steady performance. No obvious decay in activity and selectivity was observed upon 250 °C for at least 230 h (Fig. 5). Technically, the monolithic metal-oxide catalysts built on Cu-gauze have many benefits including a wide range of space velocity (4–15 h−1), more efficient heat/mass transfer with lower temperature rising and pressure drop in catalyst bed as shown in Supplementary Fig. 39 (ref. 30), as well as better interphase contact. These benefits can be potentially extended to other related industrial processes, such as vehicle emissions control and volatile organic compounds removal.
In summary, a variety of metal/oxide combinations have been demonstrated as highly active and selective catalysts for the gas-phase aerobic oxidation of benzyl alcohol and other primary alcohols. The metal-oxide interface is identified as the active sites, on the basis of STM measurements on FeO/Pt(111) and Cu2O/Ag(111) model catalysts as well as DFT calculations. The boundary oxygen, which comes from facile O2 dissociation at the interfacial sites, facilitates the adsorption of benzyl alcohol and O–H bond cleavage through a strong binding with the hydrogen of hydroxyl group. A proper oxygen binding strength plays a crucial role in a complete catalytic circle and is proposed to be a general energy descriptor for highly active catalysts. We also prove that the interfacial effects are size insensitive by comparing the three types of interface designs, that is, nanocomposite, nano-metal/micro-oxide, and the inverse nano-oxide/micro-metal. We point out that the inverse nano-oxide/micro-metal catalyst offers a promising solution to particle sintering problem which usually accounts for catalyst deactivation. With these fundamental insights, we further develop a practical monolithic catalyst on Cu gauze, which exhibits exceptional long-term stability, wide space velocity, efficient heat/mass transfer, and low pressure drop. This study highlights the importance of determining the active sites for the rational development of better catalysts beyond laboratory interest.
Pt NPs, Pd NPs, PdCu nano-alloy, Ag-Cu2O nanocomposite, Ag, Cu2O, transition metal oxides (TMO) NPs and the catalyst samples were characterized by powder X-ray diffraction (Bruker D8-advance X-ray powder diffractometer (Cu Kα, λ=1.5406 Å)), transmission electron microscope (TEM, Hitachi model H-800), HRTEM (recorded by a FEI Tecnai G2 F20 S-Twin high-resolution transmission electron microscope working at 200 kV and a FEI Titan 80–300 transmission electron microscope equipped with a spherical aberration (Cs) corrector for the objective lens working at 300 kV), and scanning electron microscope (JSM-6301F). XPS were recorded on a VG EscaLab 220i-XL spectrometer using a standard Al Kα X-ray source (300 W) and an analyzer pass energy of 20 eV. All binding energies were referenced to the adventitious C1s line at 284.9 eV. Specific surface area was determined from N2 adsorption isotherm at −196 °C using standard Brunauer–Emmett–Teller (BET) theory. Before the measurement of N2 adsorption, degassing was conducted at 300 °C for 4 h. The catalyst loadings were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) on a Thermo Scientific iCAP 6300 ICP spectrometer.
Gas-phase alcohol oxidation test
The gas-phase selective oxidation of alcohols was performed on a fixed-bed quartz tube reactor (700 mm in length and 7 mm of inner diameter) under atmospheric pressure. Catalyst was loaded in the tube reactor. Alcohols were continuously fed into the reactor using a high-performance liquid pump in parallel with air feeding using calibrated mass flow controllers. Weight hourly space velocity was calculated by dividing the weight of the fed alcohols per hour by that of catalyst. The effluent was cooled using an ice-salt bath (−15 °C) to liquefy the condensable vapors for analysis using an HP 5890 gas chromatography-flame ionization detector with a 60 m HP-5 ms capillary column. The gas-phase products, such as H2, COx and C1–C3 hydrocarbons, were analysed using an HP-5890 GC with thermal conductivity detector and a 30 m AT-plot 300 capillary column.
The experiments were carried out in a combined ultrahigh vacuum (UHV) system equipped with Createc low temperature scanning tunnelling microscope (LT-STM), XPS, UPS and the cleaning facilities. The STM and preparation chambers have a base pressures of 4 × 10–11 mbar and 6 × 10–11 mbar, respectively. The Pt(111) single crystal (Matek) was cleaned by cycles of Ar ion sputtering (1.5 keV, 10 μA) and annealing at 1,200 K. Nano-sized FeO islands were deposited onto Pt(111) by vapor deposition of Fe atoms in an O2 atmosphere (P(O2)=1 × 10–7 Torr) with the temperature of Pt(111) held at 300 K. The as-deposited surface was then annealed in UHV at 500 K, leading to the formation of well-ordered FeO islands. The Ag(111) single crystal (Matek) was cleaned by cycles of Ar ion sputtering (1.5 keV, 10 μA) and annealing at 800 K. Cu2O islands were deposited onto Ag(111) by vapor deposition of Cu atoms in an O2 atmosphere (P(O2)=1 × 10–7 Torr) with the temperature of Ag(111) held at 117 K. The as-deposited surface was then annealed in UHV at 350 K, leading to the formation of well-ordered Cu2O islands. The sample cleaning, preparation and gas exposure were performed in the preparation chamber and STM imaging were conducted in the LT-STM chamber. STM images were processed and analysed with the SPIP software (Image Metrology, Denmark).
All the relevant data are available from the authors upon request.
How to cite this article: Zhao, G. et al. Metal/oxide interfacial effects on the selective oxidation of primary alcohols. Nat. Commun. 8, 14039 doi: 10.1038/ncomms14039 (2017).
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Enache, D. I. et al. Solvent-free oxidation of primary alcohols to aldehydes using Au-Pd/TiO2 catalysts. Science 311, 362–365 (2006).
Mallat, T. & Baiker, A. Oxidation of alcohols with molecular oxygen on solid catalysts. Chem. Rev. 104, 3037–3058 (2004).
Fan, J. et al. Low-temperature, highly selective, gas-phase oxidation of benzyl alcohol over mesoporous K-Cu-TiO2 with stable copper(I) oxidation state. J. Am. Chem. Soc. 131, 15568–15569 (2009).
Zhao, G., Hu, H., Deng, M. & Lu, Y. Microstructured Au/Ni-fiber catalyst for low-temperature gas-phase selective oxidation of alcohols. Chem. Commun. 47, 9642–9644 (2011).
Yamamoto, R. et al. Promoted partial oxidation activity of supported Ag catalysts in the gas-phase catalytic oxidation of benzyl alcohol. J. Catal. 234, 308–317 (2005).
Pina, C. D., Falletta, E. & Rossi, M. Highly selective oxidation of benzyl alcohol to benzaldehyde catalyzed by bimetallic gold-copper catalyst. J. Catal. 260, 384–386 (2008).
Graciani, J. et al. Highly active copper-ceria and copper-ceria-titania catalysts for methanol synthesis from CO2 . Science 345, 546–550 (2014).
Friedrich, M., Penner, S., Heggen, M. & Armbrüster, M. High CO2 selectivity in methanol steam reforming through ZnPd/ZnO teamwork. Angew. Chem. Int. Ed. Engl. 52, 4389–4392 (2013).
Wang, X. et al. In situ studies of the active sites for the water gas shift reaction over Cu-CeO2 catalysts: complex interaction between metallic copper and oxygen vacancies of ceria. J. Phys. Chem. B 110, 428–434 (2006).
Park, J. B. et al. Gold, Copper, and Platinum nanoparticles dispersed on CeOx/TiO2(110) surfaces: high water-gas shift activity and the nature of the mixed-metal oxide at the nanometer level. J. Am. Chem. Soc. 132, 356–363 (2010).
Xu, W. et al. In situ studies of CeO2-supported Pt, Ru, and Pt–Ru alloy catalysts for the water-gas shift reaction: active phases and reaction intermediates. J. Catal. 291, 117–126 (2012).
Zhang, S. et al. WGS catalysis and in situ studies of CoO1−x, PtCon/Co3O4, and PtmCom′/CoO1−x nanorod catalysts. J. Am. Chem. Soc. 135, 8283–8293 (2013).
Liu, L. et al. Low-temperature CO oxidation over supported Pt, Pd catalysts: particular role of FeOx support for oxygen supply during reactions. J. Catal. 274, 1–10 (2010).
Green, I. X., Tang, W., Neurock, M. & Yates, J. T. Spectroscopic observation of dual catalytic sites during oxidation of CO on a Au/TiO2 catalyst. Science 333, 736–739 (2011).
Herzing, A. A., Kiely, C. J., Carley, A. F., Landon, P. & Hutchings, G. J. Identification of active gold nanoclusters on iron oxide supports for CO oxidation. Science 321, 1331–1335 (2008).
Abad, A., Concepcion, P., Corma, A. & Garcia, H. A collaborative effect between gold and a support induces the selective oxidation of alcohols. Angew. Chem. Int. Ed. Engl. 44, 4066–4069 (2005).
Abad, A., Corma, A. & Garcia, H. Catalyst parameters determining activity and selectivity of supported gold nanoparticles for the aerobic oxidation of alcohols: the molecular reaction mechanism. Chem. Eur. J. 14, 212–222 (2008).
Bauer, J. et al. Silica-supported Au–CuOx hybrid nanocrystals as active and selective catalysts for the formation of acetaldehyde from the oxidation of ethanol. ACS Catal. 2, 2537–2546 (2012).
Redina, E. A. et al. Selective oxidation of ethanol to acetaldehyde over Au–Cu catalysts prepared by a redox method. Catal. Today 241, 246–254 (2015).
Yao, Y., Fu, Q., Wang, Z., Tan, D. & Bao, X. Growth and characterization of two dimensional FeO nanoislands supported on Pt(111). J. Phys. Chem. C 114, 17069–17079 (2010).
Fu, Q. et al. Interface-confined ferrous centers for catalytic oxidation. Science 328, 1141–1144 (2010).
Fu, Q. et al. Reversible structural transformation of FeO(x) nanostructures on Pt under cycling redox conditions and its effect on oxidation catalysis. Phys. Chem. Chem. Phys. 15, 14708–14714 (2013).
Hansen, J. Ø. et al. Direct evidence for ethanol dissociation on rutile TiO2(110). Phys. Rev. Lett. 107, 136102 (2011).
Kim, Y. et al. Reactivity of FeO(111)/Pt(111) with alcohols. J. Phys. Chem. C 113, 20020–20028 (2009).
Yang, F. et al. Identification of 5–7 defects in a copper oxide surface. J. Am. Chem. Soc. 133, 11474–11477 (2011).
Eren, B., Heine, C., Bluhm, H., Somorjai, G. A. & Salmeron, M. Catalyst chemical state during CO oxidation reaction on Cu(111) studied with ambient pressure XPS and NEXAFS. J. Am. Chem. Soc. 137, 11186–11190 (2015).
Lu, J. L. et al. Coking- and sintering-resistant palladium catalysts achieved through atomic layer deposition. Science 335, 1205–1208 (2012).
Goldstein, A. N., Echer, C. M. & Alivisatos, A. P. Melting in semiconductor nanocrystals. Science 256, 1425–1427 (1992).
Atkins, P. & Jones, L. in Chemical Principles (W. H. Freeman, New York, 2008).
Harris, D. K., Cahela, D. R. & Tatarchuk, B. J. Wet layup and sintering of metal-containing microfibrous composites for chemical processing opportunities. Compos. Part A Appl. Sci. Manuf. 32, 1117–1126 (2001).
This work was supported by the National Natural Science Foundation of China (21521091, 21131004, 21390393, 21303195, 21473191, U1463202), Ministry of Science and Technology of China (2013CB933100) and Strategic Priority Research Program of the Chinese Academy of Sciences (XDB17020200). We also appreciate Lin Hu, Jinlong Yang, Yanggang Wang and Jun Li for helpful discussions.
The authors declare no competing financial interests.
About this article
Cite this article
Zhao, G., Yang, F., Chen, Z. et al. Metal/oxide interfacial effects on the selective oxidation of primary alcohols. Nat Commun 8, 14039 (2017). https://doi.org/10.1038/ncomms14039
Fine-tuning inverse metal-support interaction boosts electrochemical transformation of methanol into formaldehyde based on density functional theory
Chinese Chemical Letters (2021)
Nanoscale Advances (2020)
Ag–CoO nanocomposites for gas-phase oxidation of alcohols to aldehydes and ketones: intensified O2 activation at Ag–CoO interfacial sites
Catalysis Science & Technology (2020)
Monolithic Ag-Cu2O/Ti-foam for the gas phase oxidation of alcohols: Synergistic effect between Ag and Cu2O
Catalysis Communications (2020)
In situ observations of the structural dynamics of platinum–cobalt–hydroxide nanocatalysts under CO oxidation