Ultrathin electronic circuits that can be manufactured by using conventional printing technologies are key elements necessary to realize wearable health sensors and next-generation flexible electronic devices. Due to their low level of power consumption, complementary (CMOS) circuits using both types of semiconductors can be easily employed in wireless devices. Here, we describe ultrathin CMOS logic circuits, for which not only the source/drain electrodes but also the semiconductor layers were printed. Both p-type and n-type organic thin film transistor devices were employed in a D-flip flop circuit in the newly developed stacked structure and exhibited excellent electrical characteristics, including good carrier mobilities of 0.34 and 0.21 cm2 V−1 sec−1 and threshold voltages of nearly 0 V with low operating voltages. These printed organic CMOS D-flip flop circuits exhibit operating frequencies of 75 Hz and demonstrate great potential for flexible and printed electronics technology, particularly for wearable sensor applications with wireless connectivity.
In recent years, there has been great interest in the use of organic thin film transistor (OTFT) device technology in next-generation thin film electronics, due to the performance enhancements enabled by its use in applications such as flexible displays1,2, large-area sensors3,4, radio frequency identification (RFID) tags5,6 and ultrathin electronics7,8,9. In particular, ultrathin devices have received significant consideration for use in practical wearable devices and RFID tags that operate wirelessly and should consume low power and have a small circuit footprint. A complementary (CMOS) logic configuration is suitable for such devices because of its low power consumption and smaller physical layout compared with the unipolar p-MOS or n-MOS circuit configurations.
Fabrication of OTFT-based circuits using conventional printing technologies is considered a promising approach due to advantages such as low capital investment, efficient utilization of material and low production cost, motivating extensive research on the fabrication of organic CMOS integrated circuits either entirely or in part by using printing methods. Some studies have examined the printing of circuits that use organic semiconductors (p and n type)10,11,12, while others have investigated hybrid configurations using both inorganic and organic semiconductors13,14. However, these reports used low performance n-type organic semiconductors or vacuum deposited electrodes.
Currently, the optimization of the electrical characteristics of p-type and n-type OTFT devices requires the modification of the electrode surfaces by using a self-assembled monolayer (SAM)15, oxide layer16, or polymer layer17 processes for the different semiconductor materials. Unfortunately, complex processes such as SAM patterning using a plasma treatment5 are required to form the source and drain electrodes of each of n and p type OTFT devices on the same substrate, which are unsuitable for volume production and prevent the use of organic transistors in practical applications. To overcome this limitation, we have devised a structure for forming vertically stacked p-type and n-type OTFT devices. By combining printing methods with this stacked device structure and using an ultrathin substrate, the processing time is short and total device thickness remains very thin. There have been some reports regarding the use of stacked structures to obtain high density integrated circuits18, to control of OTFT device characteristics19 and to combine inorganic and organic device processes20 for the fabrication of the integrated circuits. However, an electrode surface modification technology for the solution-processed semiconductors has not yet been developed.
In this study, we have demonstrated a CMOS inverter logic gate as well as ring oscillator and D-flip flop (FF) circuits on a micron-thick substrate by stacking the solution-processed OTFT devices. To reduce the complexity of the CMOS inverter circuit fabrication, we developed a sophisticated stacked-structure printing process. This fabrication process exhibits the following advantages: 1) simple electrode surface modification with different SAM layers, 2) use of a common gate electrode layer to simplify the circuit layout, 3) top-gate, bottom-contact (TG-BC) device structure to maximize and take advantage of the performance of the n-type OTFT. As a result, excellent electrical characteristics were achieved in both p and n type OTFT devices with printed electrodes and solution-processed semiconductor layers. In addition, the fabricated CMOS inverter circuit operated successfully at low operating voltages of 1–10 V, as did the master–slave (MS)-type D-FF circuit with the output buffer consisting of forty (40) transistors on the ultrathin substrate. Furthermore, we successfully fabricated these integrated circuits on a 1-μ m thick film substrate and have demonstrated their ability to operate even when this film is compressed.
Fabrication of stacked organic complementary logic circuits on ultrathin substrates
The fabricated inverter logic gate has a stacked configuration consisting of n-type OTFT with TG-BC structure overlapping on a p-type OTFT with BG-BC structure of (Fig. 1a). This device structure has several advantages, including and most importantly, the fact that the electrode surface modification process in the complementary configuration is simplified. In an organic transistor with printed electrodes, surface treatment of the source and drain electrodes using a SAM layer is very important for improving the OTFT characteristics22. In this device configuration, the fabrication processes for the p-type and n-type OTFT devices are performed separately. Therefore, the electrode surface treatment for both OTFT device types can be carried out using a simple immersion process. This is in contrast to surface treatment methods using an O2 plasma previously reported in work by Battiato et al.5, which is necessitated by the formation of both OTFT device types on the same layer and is one of the inevitable drawbacks that reduces the benefits of the printing processes. In another study, a staggered device structure was reported to be electrically superior to a planar structure23. Therefore, we used a TG-BC structure for the n-type OTFT device.
Figure 1b shows a photograph of the ultrathin organic CMOS logic circuit. The procedure for device fabrication on an ultrathin film substrate was reported previously21. The substrate consists of parylene diX-SR is only 1 μ m thick, such that the total thickness of the stacked OTFT devices is less than 3 μ m. The fabricated devices can be easily peeled from the supporting glass plate after completing the entire fabrication process. All device layers were fabricated with printing processes except for deposition of the parylene layer. These ultrathin devices demonstrate the feasibility of the multi-layer stacked device structures for highly integrated circuits with lightweight that can adhere to any surface and over large areas.
Figure 1c shows an optical microscope image of the fabricated inverter circuit. To obtain geometric information, we observed the p-type OTFT and n-type OTFT devices with a polarization microscope after fabricating the two OTFT devices in separate areas. Figure 1d shows the polarization microscope image of p-type and n-type semiconductors. Both semiconductor films are polycrystalline, which we concluded is the likely reason for the reduced variations in n-type OTFT device electrical characteristics. (see Supplementary Information, Fig. S1).
Electrical performance of p- and n-type OTFT devices in CMOS inverters
Figure 2a,b show the chemical formula of the organic semiconductors used in the complementary (CMOS) inverter gate. For the p-type semiconductor, we used an ink consisting of a diF-TES-ADT and PS blend, which is known to be a high performance organic semiconductor24,25,26,27. A novel solution-processable n-type semiconductor called TU-328,29,30 was developed in collaboration with Ube Industries, Ltd. Although its basic chemical structure is rigid benzobis(thiadiazole) (BBT), TU-3 shows high solubility in many common organic solvents.
We evaluated the effectiveness of the SAM modification process on a printed silver electrode using photoemission spectroscopy. The work function of the bare electrodes was 4.8 eV, changing to 5.3 and 4.0 eV after pentafluorobenzenethiol (PFBT) and 4-methylbenzenethiol (4-MBT) treatments, respectively. (see Supplementary Information, Fig. S2)
We then measured the transistor characteristics of the OTFT devices that make up the inverter circuit in ambient air conditions. Figure 2c,d show the transfer characteristics of the p-type and n-type OTFT devices, respectively and Fig. 2e,f show the corresponding output characteristics. The channel length (L) and width (W) of the fabricated p-type and n-type OTFT devices were L/W = 52/612 and 41/2012 μ m, respectively. These OTFT devices exhibited excellent TFT device electrical performance at relatively low operating voltages of 10 V. For the p-type OTFT, the estimated hole-mobility and threshold voltage were 0.34 cm2 V−1 sec−1 and 0.17 V, respectively and the on/off current ratio was greater than 107. For the n-type OTFT, the estimated electron-mobility and threshold voltage were 0.21 cm2 V−1 sec−1 and 0.53 V and the on/off current ratio was greater than 107. These threshold voltage values were very close to the ideal value of 0 V.
Accordingly, we have successfully achieved n-type OTFT device performance comparable to that of the p-type OTFT device for balanced complementary logic functionality. These good output characteristics suggest that the contact resistance for each TFT device type is low. Since the contact resistance (Rc) of OTFT with printed electrode and semiconductor layers provides important information for understanding the electrical transport, there have been some reports on the Rc of p-type OTFT devices15,16,21. However, no Rc values have been reported for n-type OTFT devices. We estimated Rc for the n-type transistors using the transmission line method (TLM)31. Here, Rc is given by
where Rtotal is the resistance between the source and drain electrodes and the Rch is the channel resistance. To precisely calculate the contact resistance using equation (1), we fabricated TFT devices with various channel lengths and their total resistance values estimated from the output characteristics. Figure 2g,h show the TLM plots used to calculate the Rc values in n-type OTFTs. Rc is estimated to be as low as 92.6 k Ω cm at VGS = 10 V. Thus, a low Rc for the n-type TFT comparable to that of the p-type TFT was achieved by modifying the electrode surface with a SAM layer for the n-type semiconductor layer and a high-performance printed CMOS OTFT circuit was realized.
Electrical performance of CMOS inverters
To investigate the feasibility of using the stacked structure for the organic CMOS circuits, we have evaluated the inverter logic gate circuit, which is the most basic component for the complementary integrated circuits. The inverter gate operates as follows: when the input voltage (Vin) is low, the output voltage (Vout) is high; on the contrary, when Vin is high, Vout becomes low. Ideally, Vout should be equal to VDD at a high input voltage.
The inverter gate circuit requires the combination of p-type and n-type OTFT devices as shown in the inset of Fig. 3a. Generally, the static and dynamic electrical performances of lf inverter gate circuits are evaluated. In this section, we describe the voltage gain characteristics, trip point and noise margin of the static characteristics with dynamic characteristics described in the subsequent section. Figure 3a,b display the voltage transfer characteristics at various VDD supply voltages. The sharp switching is one of the major advantages of the CMOS logic gates. Inversion characteristics with small hysteresis as low as 3% of VDD are obtained for VDD ranging from 1 to 10 V. Furthermore, voltage gain values are as high as ~20 at a VDD of 5–10 V, ~10 at a VDD of 2.5–3 V and ~3 at a VDD of 1 V. Here, the voltage gain is defined as the absolute value of ∆ Vout/∆ Vin. The trip point is defined as the input voltage Vin at Vout = Vin. In an ideal inverter gate, the trip point should be equal to one half of VDD. Figure 3a,b show that the trip points are indeed close to half of the VDD value and are 6.3, 4.7, 3.1 and 1.3 V at VDD of 10, 7.5, 5 and 2.5 V, respectively.
The noise margin is defined as the side of the largest square that can be inscribed between the transfer characteristics. The maximum noise margin is equal to half of the supply voltage. Our inverter circuit shows a noise margin of greater than 50% at a VDD from 2 to 10 V. This is the highest noise margin reported so far for printed CMOS organic inverters32.
D flip-flop based on CMOS inverters
To further demonstrate the capability of our process, we have fabricated a practical D-FF circuit is a basic circuit to configure registers and bit counters.
A complementary MS-type D-FF circuit construction is depicted in Fig. 4a. This circuit is composed of forty (40) OTFT devices including a buffer inverter (more detailed circuits diagrams are provided in the supplementary information Fig. S3). Figure 4b shows the images of the fabricated devices. Even though some reports show a simpler D-FF circuit configurations, such as a transmission gate type and edge-trigger type5,33,34,35,36,37, we have evaluated a conventional MS-type consisting forty (40) OTFT devices to validate the high yield of our stacked structure. Figure 4c shows the input-output characteristics of the fabricated D-FF circuits at a supply voltage of 10 V. All electrical measurements for the D-FF circuits were carried out in the atmosphere.
This MS-type D-FF circuit reads the state of the input at a clock state of high and changes the output state at the falling edge of the clock. When the clock state is high, the output state is held. At a falling clock edge, the output state is changed or held to coincide with the input D-state. For example, the low output state is changed to and the high output state is held with the same state as the high input state at a falling clock edge. The timing chart in Fig. 4c shows that the fabricated circuit operates properly.
We then changed the clock frequency to evaluate the operating speed of the circuits. We applied a square-wave clock signal with a duty cycle of 50% and showed that the D-FF functions correctly at a clock frequency of 75 Hz (13.3 ms/clock cycle). This value is approximately equal to the 80 Hz estimated by the circuit simulation (see Supplementary Information Fig. S4). In previously reported work by Schwartz et al.38, an MS-type FF with printed electrodes was operated at a speed of 10 ms/clock cycle and a supply voltage of 20 V. Therefore, a clock speed of 13.3 ms is a compatible value with the supply voltage of 10 V.
To demonstrate the light weight and flexibility of the circuit, we operated the circuit while under the influence of strong current of air. Even under these conditions, the circuit functioned without any degradation in electrical performance (see Supplementary Information movie S1).
Mechanical compressibility of the integrated circuits
The stability of the fabricated circuits under compression was evaluated by measuring the oscillation frequency of a 3-stage ring oscillator. Following the procedure used in our previous work21, we affixed the circuit’s film substrate to a pre-stretched elastomer. When the elastomer was released from the stretched condition to the original condition, the circuit film was compressed. Figure 5a shows the oscillation frequency of the ring oscillator at the corresponding compression ratios. In the original state, for which the compression ratio is defined as 0%, the oscillation frequency was 217.7 Hz and the delay time per stage was 0.77 ms. Such a delay time is considered excellent for a solution-processed ring oscillator with low operation voltages39. Upon compression of the film by 20%, the oscillation frequency changed slightly to 194.9 Hz and the delay per stage was 0.86 ms. However, the devices could not function at a compression ratio of 30%. To investigate the origin of this effect, we evaluated the transistor properties in a compressed state. Figure 5a,b show the transfer characteristics of the p-type and n-type OTFT devices at conditions before and after 50% compression, respectively. The mobility of p-type TFT decreased by 6.2% after the compression and the threshold voltage shifted by − 0.11 V.
Compared to the p-type OTFT device, the performance of the n-type OTFT device was much worse after the compression. The mobility was reduced by 40% and the threshold voltage was shifted by − 0.42 V.
In the organic semiconductor, there are decrease of injection efficiency due to the increase of potential barrier at the electrode interface and increase of the contact resistance which induce the mobility degradation and threshold voltage shift simultaneously40. Therefore, it is suggested that the potential-barrier increased by compression is one of the cause for these characteristics variations.
Because normal transistor characteristics were obtained even when the film was compressed by 50%, we suspect that the ring oscillator stopped oscillating because of poor contact through a via hole to the power-supply interconnect lines. Since this is not an essential process for the OTFT device and circuit, this malfunction of the circuit can be eliminated by improving the printing processes for the interconnect and the integrity of the via hole.
In conclusion, we have successfully fabricated complementary (CMOS) logic circuits with low-voltage operation using OTFT devices with a novel stacked configuration, which employs a SAM modification treatment using a simple immersion process and uses printing methods to form the source/drain electrode and semiconductor layers on ultrathin film substrates, thus realizing all-printed n-type and p-type OTFT devices with a total thickness of 3 μ m or less.
Both OTFT devices showed excellent carrier mobilities of more than 0.2 cm2 V−1 sec−1 and the carrier mobility of the n-type semiconductor was the highest ever reported for printed complementary circuits. The threshold voltage of the fabricated devices was sufficiently low; hence, the digital logic gate was driven at a low operating voltage of only 5 V. In addition, the fabricated inverter gate was able to perform the proper inversion operations at very low operating voltages of 1.5 V and was shown to operate successfully even under compression.
As a result, we are the first to demonstrate printed complementary CMOS OTFT process and circuits on an ultrathin film substrate with a thickness of 1 μ m. We believe that this technology will be instrumental in the development of future flexible and printed electronic applications, particularly wearable sensors.
Mesitylene-based 2,8-difluoro-5,11-bis(triethylsilylethynyl)anthradithiophene (diF-TES-ADT)41 2 wt%/Polystyrene (PS, average Mw ~280,000, Sigma-Aldrich) 0.5 wt% blend solution was used for the p-type semiconductor24,25,26,27. The novel n-type semiconductor based on benzobis (thiadiazole) (BBT) derivative (TU-3, Ube Industries, Ltd.)28,29,30 was prepared in a 0.06 wt% solution for printing using 1-methylnaphthalene (TCI).
The complementary (CMOS) inverter logic gates have a stacked structure and the device structure for each of the n-type and p-type OTFT devices are top-gate, bottom-contact (TG-BC) and bottom-gate, bottom contact (BG-BC), respectively.
The CMOS logic gates are based on solution-processable semiconductors and printed electrodes that were fabricated on a 1-μ m-thick parylene film substrate21. A 700-μ m-thick glass substrate with a peeling layer was used as a supporting plate to enable easier handling of the 1-μ m- thick film.
A 1 wt% amorphous fluoropolymer (Teflon AF 1600, DuPont) in Fluorinert (FC-43, 3M Co.) was used for the peeling layer and was formed by spin-coating.
A 1-μ m-thick parylene layer (diX-SR, KISCO LTD.) was deposited on the peeling layer with a PDS 2010 LABCOTER 2 parylene coater (Specialty Coating Systems) and then the substrate was annealed at 120 °C for 1 hour in the ambient conditions.
We have prepared devices using the NPS-JL (Harima Chemicals Inc.) which is commonly available silver nanoparticle ink containing 52–57 wt% silver nanoparticles with an average diameter of 7 nm in tetradecane, resistivity 9.5 μ Ω cm, viscosity 8–15 mPa s42. This silver nanoparticles ink was printed with a piezoelectric ink-jet printer (DMP-2831, Fujifilm Dimatix Co.) using a 10 pL cartridge for all electrodes, including the source, drain and gate electrodes and the interconnect lines. The cartridge temperature and the plate temperature were maintained at 40 °C and 50 °C, respectively. The drop spacing (DS) was 60 μ m; this value was optimized to obtain fine printed electrodes. After the printing processes, the substrates were sintered at 120 °C for 30 min in ambient conditions. Next, solution amorphous fluoropolymer was patterned using a dispenser system (IMAGEMASTER 350, Musashi Engineering, Inc.) to create hydrophobic bank layers that confined the deposited n-type organic semiconductor layer and were subsequently cured at 100 °C for 30 min in air. Prior to the deposition of the semiconductor layer, the source and drain electrode surfaces were modified by immersing them in a 10 mM solution of 4-MBTin isopropanol for 5 min and then rinsing with pure isopropanol43. The n-type semiconductor solution (TU-3) was applied in the areas defined by the bank layers using the dispenser system. During the dispenser printing process, the substrate and nozzle temperatures were 60 °C and 30 °C, respectively. Dispensing conditions were optimized to improve the performance of the n-type OTFT, whereby the discharge pressure was 10 kPa and the discharge time was about 200 ms. The conditions for the crystal growth process (drying process of 1-methylnaphthalene) were maintained in atmosphere at 60 °C for 30 min. After drying the n-type semiconductor layer, the substrates were annealed at 120 °C for 30 min. in a nitrogen ambient. The parylene layer was deposited and annealed under the same conditions as 1 μ m substrate layers to form the 260-nm-thick gate dielectric layer of the n-type OTFT. The silver nanoparticle ink was printed and sintered under the same conditions as the source and drain electrodes to form gate electrodes for both the n-type and p-type OTFT devices at the same time. After printing the gate electrodes, the parylene layer was deposited under the same conditions as that for the n-type OTFT device dielectric layer to form the gate dielectric layer for the p-type OTFT device. The via holes were formed by a YAG laser (VL-C30, V-Technology Co., Ltd.) and the wavelength output 355 nm. Next, the silver nanoparticle ink was patterned and sintered in the same conditions as the other electrodes to form the source and drain electrodes for the p-type OTFT device. Next, hydrophobic bank layers were printed by using the dispenser system for defining the channel width of the p-type OTFT devices under the same conditions as for the n-type OTFT device layer. Prior to the printing of the p-type semiconductor layer, the source and drain electrode surfaces were modified by immersing them in a 30 mM solution of PFBT in isopropanol for 5 min and then rinsing with pure isopropanol44,45. Finally, a mesitylene-based solution containing a p-type semiconductor was printed in the areas defined by bank layer using the ink-jet printer. During this time, the cartridge temperature and the plate temperature were maintained at 30 °C. After drying the semiconductor layer, a 540 nm-thick parylene layer was deposited as the encapsulation layer. These solution-processable CMOS inverter gate fabrication processes were used to create the ring oscillator and D-FF fcircuits.
The electrical characteristics of the fabricated organic TFT devices and static performance of logic circuits were measured using a semiconductor parameter analyzer (Keithley, model 4200-SCS), whereby all electrical measurements were carried out in air. Photographs of the fabricated devices were obtained using a laser microscope (Olympus, model OLS-4000). The metal surface work function was measured using photoemission spectroscopy (Riken Keiki, model AC-3). The dynamic performance of the integrated logic circuits was measured by using a function generator (Keysight, model 33522B) and an oscilloscope (Tektronix, model DPO2024B) with a passive voltage probe (Tektronix, model TPP0200).
How to cite this article: Takeda, Y. et al. Fabrication of Ultra-Thin Printed Organic TFT CMOS Logic Circuits Optimized for Low-Voltage Wearable Sensor Applications. Sci. Rep. 6, 25714; doi: 10.1038/srep25714 (2016).
Mizukami, M. et al. A Solution-Processed Organic Thin-Film Transistor Backplane for Flexible Multiphoton Emission Organic Light-Emitting Diode Displays. IEEE Electron Dev. Lett. 36, 841–843 (2015).
Nomoto, K. Development of flexible displays driven by organic TFTs. SID Symp. Dig. Tech. Paper 41, 1155–1158 (2010).
Someya, T. et al. Integration of organic FETs with organic Photodiodes for a large area, flexible and lightweight sheet image scanners. IEEE Trans. Electron Dev. 52, 2502–2511 (2005).
Zirkl, M. et al. Low-Voltage Organic Thin-Film Transistors with High-k Nanocomposite Gate Dielectrics for Flexible Electronics and Optothermal Sensors. Adv. Mater. 19, 2241–2245 (2007).
Fiore, V. et al. An Integrated 13.56-MHz RFID Tag in a Printed Organic Complementary TFT Technology on Flexible Substrate. IEEE Trans. Circuits and Systems 62, 1668–1677 (2015).
Myny, K. et al. Bidirectional Communication in an HF Hybrid Organic/Solution-Processed Metal-Oxide RFID Tag. IEEE Trans. Electron Dev. 61, 2387–2393 (2014).
Kaltenbrunner, M. et al. An ultra-lightweight design for imperceptible plastic electronics. Nature 499, 458–463 (2013).
White, M. S. et al. Ultrathin, highly flexible and stretch-compatible PLEDs. Nature Photon. 7, 811–816 (2013).
Wu, X. et al. Thermally Stable, Biocompatible and Flexible Organic Field-Effect Transistors and Their Application in Temperature Sensing Arrays for Artifi cial Skin. Adv. Funct. Mater. 25, 3138–2146.
Maiellaro, G. et al. High-Gain Operational Transconductance Amplifiers in a Printed Complementary Organic TFT Technology on Flexible Foil. IEEE Trans. Circuits and Systems 60, 3117–3125 (2013).
Ng, T. N. et al. Scalable printed electronics: an organic decoder addressing ferroelectric non-volatile memory. Sci. Rep. 2, 585 (2012).
Tee, B. C.-K. et al. A skin-inspired organic digital mechanoreceptor. Science 350, 313–316 (2015).
Myny, K. et al. A thin-film microprocessor with inkjet print-programmable memory. Sci. Rep. 4, 7398 (2014).
Guo, X. et al. Low voltage Organic/Inorganic Hybrid Complementary Inverter With Low Temperature All Solution Processed Semiconductor and Dielectric Layers. IEEE Electron Dev. Lett. 35, 542–544 (2014).
Kim, C.-H. et al. Decoupling the Effects of Self-Assembled Monolayers on Gold, Silver and Copper Organic Transistor Contacts. Adv. Mater. Interfaces. 2, 1400384 (2015).
Kumaki, D. et al. Reduced contact resistance and highly stable operation in polymer thin-film transistor with aqueous MoOx solution contact treatment. Org. Electron. 14, 475–478 (2013).
Zhou, Y. et al. A Universal Method to Produce Low–Work Function Electrodes for Organic Electronics. Science 336, 327–332 (2012).
Seo, S.-M. et al. Stacking of Organic Thin Film Transistors: Vertical Integration. Adv. Mater. 20, 1994–1197 (2008).
Baek, C. et al. Vertical organic inverter with stacked pentacene thin film transistors. Appl. Phys. Lett. 94, 153305 (2009).
Kim, J. B. et al. Vertically stacked hybrid organic-inorganic complementary inverters with low operating voltage on flexible substrates. Org. Electron. 12, 45–50 (2011).
Fukuda, K. et al. Fully-printed high-performance organic thin-film transistors and circuitry on one-micron-thick polymer films. Nat. Commun. 5, 4147 (2014).
Yoshimura, Y. et al. High-speed operation in printed organic inverter circuits with short channel length. Org. Electron. 15, 2696–2701 (2014).
Shim, C.-H. et al. Structural Analysis on Organic Thin-Film Transistor With Device Simulation. IEEE Trans. Electron Devices 57, 195–200 (2010).
Hamilton, R. et al. High-Performance Polymer-Small Molecule Blend Organic Transistors. Adv. Mater. 21, 1166–1171 (2009).
Naden, A. B. et al. Structure–function relations in diF-TES-ADT blend organic field effect transistors studied by scanning probe microscopy. J. Mater. Chem. C 2, 245–255 (2014).
Smith, J. et al. Solution-Processed Small Molecule-Polymer Blend Organic Thin-Film Transistors with Hole Mobility Greater than 5 cm2/Vs. Avd. Mater. 24, 2441–2446 (2012).
Smith, J. et al. Percolation behaviour in high mobility p-channel polymer/small-molecule blend organic field-effect transistors. Org. Electron. 12, 143–147 (2011).
Mamada, M. et al. A Unique Solution Processable n-Type Semiconductor Material Design for High Performance Organic Field-Effect Transistors. Chem. Mater. 27, 141–147 (2015).
Tokito, S. et al. UBE Industries, Ltd. and National University Corporation Yamagata University, assignee. Benzobis(Thiadiazole) Derivative and Organic Electronics Device Using Same. Wipo patent WO/2013/141182. 2013 September 26.
Tokito, S. et al. UBE Industries, Ltd. and National University Corporation Yamagata University, assignee. Benzobis (Thiadiazole) Derivative, Ink Containing Same and Organic Electronic Device Using Same. Wipo patent WO/2015/041026. 2015 March 26.
Klauk, H. et al. Contact resistance in organic thin film transistors. Solid-State Electron 47, 297–301 (2003).
Hambsch, M. et al. Comparison of fully printed unipolar and complementary organic logic gates. Org. Electron. 13, 1989–1995 (2012).
Gelinck, G. et al. Organic Transistors in Optical Displays and Microelectronic Applications. Adv. Mater. 22, 3778–3798 (2010).
Xia, Y. et al. Printed Sub-2 V Gel-Electrolyte-Gated Polymer Transistors and Circuits. Adv. Funct. Mater. 20, 587–594 (2010).
Dell’Erba, G. et al. Organic integrated circuits for information storage based on ambipolar polymers and charge injection engineering. Appl. Phys. Lett. 104, 153303 (2014).
Yoo, B. et al. Organic Complementary D Flip Flops Enabled by Perylene Diimides and Pentacene. IEEE Electron Dev. Lett. 27, 737–339 (2006).
Kim, B. et al. Complementary D Flip-Flops Based on Inkjet Printed Single-Walled Carbon Nanotubes and Zinc Tin Oxide. IEEE Electron Dev. Lett. 40, 1245 (2014).
Schwartz, D. E. et al. Comparison of Static and Dynamic Printed Organic Shift Registers. IEEE Electron Dev. Lett. 34, 271–273 (2013).
Jacob, S. et al. High performance printed N and P-type OTFTs enabling digital and analog complementary circuits on flexible plastic substrate. Solid-State Electron. 84, 167–178 (2013).
Kano, M. et al. Improvement of subthreshold current transport by contact interface modification in p-type organic field-effect transistors. Appl. Phys. Lett. 94, 143304 (2009).
Subramanian, S. et al. Chromophore Fluorination Enhances Crystallization and Stability of Soluble Anthradithiophene Semiconductors. J. Am. Chem. Soc. 130, 2706–2707 (2008).
Takeda, Y. et al. Integrated circuits using fully solution-processed organic TFT devices with printed silver electrodes. Org. Electron. 14, 3362–3370 (2013).
Kitamura, M. et al. High-Frequency Organic Complementary Ring Oscillator Operating up to 200 kHz. Appl. Phys. Express 4, 051601 (2011).
Takeda, Y. et al. Flip-flop logic circuit based on fully solution-processed organic thin film transistor devices with reduced variations in electrical performance. Jpn. J. Appl. Phys. 54, 04DK03 (2015).
Hong, J.-P. et al. Tuning of Ag work functions by self-assembled monolayers of aromatic thiols for an efficient hole injection for solution processed triisopropylsilylethynyl pentacene organic thin film transistors. Appl. Phys. Lett. 92, 143311 (2008).
This work was supported by the JSPS KAKENHI Grant Number 15J07917. We also thank Mr. C. Shepherd for his technical support and helpful discussion and Ube industries, Ltd. for providing materials (n-type semiconductor: TU-3). The authors would like to thank Enago (www.enago.jp) for the English language review.
The authors declare no competing financial interests.
About this article
Cite this article
Takeda, Y., Hayasaka, K., Shiwaku, R. et al. Fabrication of Ultra-Thin Printed Organic TFT CMOS Logic Circuits Optimized for Low-Voltage Wearable Sensor Applications. Sci Rep 6, 25714 (2016). https://doi.org/10.1038/srep25714
This article is cited by
High-speed hybrid complementary ring oscillators based on solution-processed organic and amorphous metal oxide semiconductors
Communications Materials (2023)
Nano-Micro Letters (2022)
Communications Materials (2021)
Electrode and dielectric layer interface device engineering study using furan flanked diketopyrrolopyrrole–dithienothiophene polymer based organic transistors
Scientific Reports (2020)
Nature Communications (2019)