Cochlear-implant (CI) users rely on temporal envelope modulations (TEMs) to understand speech, and clinical outcomes depend on the accuracy with which these TEMs are encoded by the electrically-stimulated neural ensembles. Non-invasive EEG measures of this encoding could help clinicians identify and disable electrodes that evoke poor neural responses so as to improve CI outcomes. However, recording EEG during CI stimulation reveals huge stimulation artifacts that are up to orders of magnitude larger than the neural response. Here we used a custom-built EEG system having an exceptionally high sample rate to accurately measure the artefact, which we then removed using linear interpolation so as to reveal the neural response during continuous electrical stimulation. In ten adult CI users, we measured the 40-Hz electrically evoked auditory steady-state response (eASSR) and electrically evoked auditory change complex (eACC) to amplitude-modulated 900-pulses-per-second pulse trains, stimulated in monopolar mode (i.e. the clinical default), and at different modulation depths. We successfully measured artifact-free 40-Hz eASSRs and eACCs. Moreover, we found that the 40-Hz eASSR, in contrast to the eACC, showed substantial responses even at shallow modulation depths. We argue that the 40-Hz eASSR is a clinically feasible objective measure to assess TEM encoding in CI users.
Electrical stimulation of the auditory nerve, by means of a cochlear implant (CI), restores hearing to severely-hearing impaired people1. CIs are especially successful when listening to speech in quiet. However, performance with a CI deteriorates markedly when listening conditions become more challenging, e.g. speech in noise. Speech intelligibility in challenging listening situations depends heavily on the speech features available to the CI user. CI users do well in quiet listening conditions, since only a limited number of spectral channels are required to perceive speech intelligibly as long as the temporal envelope modulations (TEMs) of speech are preserved2,3. Conventional CI stimulation strategies are based on this phenomenon and predominately transmit the TEMs of the received acoustical signal to the auditory nerve by means of a limited number of spectral channels4. Conventional CIs have between 12 to 24 stimulation electrodes but, due to current spread within the cochlea, listeners only have access to 8 to 10 independent channels of information5,6,7,8. Some CI users, however, benefit from more spectral channels when facing more challenging listening conditions9,10.
The ability of the stimulated neural ensembles to encode the TEMs is, apart from the perceptually unique spectral channels available to the CI user, important for speech perception11. Studies of behavioral and electrophysiological assessments of TEM encoding show that a uniformly poor or highly variable TEM encoding across the stimulated neural ensembles is associated with degraded speech intelligibility in noise12,13. Furthermore, disabling or adjusting stimulation parameters of the CI electrodes that stimulate poor TEM encoding neural ensembles can positively affect speech perception in noise12,14,15. These findings suggest that CI users could benefit from methods that disable or re-program subsets of electrodes based on the TEM encoding abilities of the stimulated neural ensembles12,14.
For the clinical assessment of TEM encoding, reliable and time-efficient measures are needed. Objective assessment of the TEM encoding has its advantage over behavioral methods/metrics, such as the often-used modulation detection thresholds (MDTs), as they do not rely on the active cooperation of the CI recipient. Furthermore, they can be used to evaluate modulation encoding at the supra-threshold modulation depths that are important for speech perception. Potential objective measures are the electrically-evoked 40-Hz auditory steady-state response (eASSR) and the electrically-evoked auditory change complex (eACC). Both can be measured by means of non-invasive EEG techniques.
The 40-Hz eASSR is a phase-locked neural response to the temporal envelope of a 40-Hz modulated stimulus16 and originates from multiple sources across the auditory pathway; including the brainstem, thalamus and auditory cortex17,18. The 40-Hz eASSR is measurable in most adult CI users13,19, its magnitude correlates well with MDTs20, and it can capture the variability in TEM processing across the stimulated neural ensembles which is in turn associated with speech-perception-in-noise outcome13. Moreover, its acoustic analog, the ASSR, is used clinically to assess the frequency specific hearing thresholds in infants with a suspicion of hearing loss21. Measuring eASSRs in CI users is, however, extremely challenging due to the stimulation artifacts that share the same frequency characteristics as the eASSR19,22,23. This makes it difficult, without proper removal, to distinguish between a true neural response and the stimulation artifact.
Although several artifact removal methods have been reported in the literature to record eASSRs free from stimulation artifacts in CI users24,25,26,27, only linear interpolation between artifact free samples before and after the stimulation artifact (Fig. 1A) has resulted in consistent success13,19,22,28,29. Linear interpolation, however, can only be successfully applied if the artifact duration is shorter than the inter-pulse interval of the stimulation sequence. For pulse trains stimulated in monopolar mode and at clinically relevant stimulation rates, which are typically ≥ 500 pulses per second (pps), this is often not the case23. The maximum pulse rate reported in the literature for which linear interpolation is applicable is 500 pps13,19,29. One factor that affects the CI artifact duration is the sampling rate and the inherent anti-aliasing filter applied to record the EEG30. When using conventional EEG-recording this results in a distorted artifact waveform and an artifact duration that exceeds the inter-pulse intervals of clinically relevant pulse rates.
One potential alternative objective assessment of TEM encoding that is less troubled by the stimulation artifact is the ACC. The ACC is a transient cortical response to a change in stimulus—e.g., from unmodulated to modulated—that originates from the auditory cortex31,32. In the following we refer to the ACC when it is evoked in the acoustically stimulated auditory pathway and eACC when it is evoked in the electrically stimulated auditory pathway. In normal-hearing listeners the ACC strength is related to modulation detection32. Given the cortical origin of the ACC it can potentially function as a final detector of how well the TEMs are encoded in the neural signal. The ACC has been successfully used as an electrophysiological measure of gap detection33, frequency change detection34, and the eACC for electrode discrimination35,36,37 in CI users. Furthermore, the eACC N1 amplitude shows a similar pattern as the temporal modulation transfer function of CI users38. It is, however, unclear if the eACC is able to reflect the TEM encoding ability of the stimulated neural ensembles of an individual CI user.
Here we investigate how the 40-Hz eASSR and the eACC reflect TEM encoding in the auditory pathway of ten adult CI users. We use different percentages of modulation depths (MD%) to model the various degrees of TEM encoding at the level of the stimulated neural ensembles, which are known to vary across CI users and stimulation sites12,13,39. We hypothesize that both the 40-Hz eASSR and the eACC are differently affected by modulation depth, due the different origins of the two responses in the ascending auditory pathway. Furthermore, we use a hyper-rate sampling EEG system, which was specially designed—to our specifications—to limit the distortion of the artifact waveform and therefore potentially shorten the stimulation artifact duration. We hypothesize that this approach enables the removal of the stimulation artifacts when measuring neural responses from CI users, especially eASSRs, to clinically relevant stimulation rates and in monopolar mode.
Ten adult CI users took part (mean age = 56.1 years, 9 female); all had a history of long-term hearing impairment with an average CI use of 4.3 years (see “Methods” section). The study consisted of two intertwined EEG experiments. We used, in all experiments a stimulus that is representative of those used in conventional CI systems, namely a train of symmetric biphasic pulses delivered in monopolar mode at a pulse rate of 900 pulses per second (pps). First, the effectiveness of CI artifact removal was assessed. Second, the effect of MD% on the eASSR and the eACC was investigated. In the first experiment we only used amplitude modulated pulse trains so as to measure the effectiveness of artifact removal on the measurement of eASSRs. The second experiment used a stimulus consisting of a constant pulse train immediately followed by a modulated pulse train (i.e., a single trial), and measured the eACC to the change in modulation; this also allowed us to measure an eASSR to the modulated portions. The effect of MD% on the electrophysiological responses was investigated by changing the MD% of the modulated part of the stimulus from 100 to 25% across conditions. Figure 1B shows an illustration of a single stimulation trial used to assess the effect of MD% on the eACC and 40-Hz eASSR.
Behavioral assessment of stimulation levels
Behavioral thresholds, comfort levels, and equal-loudness levels were assessed prior to each EEG experiment. This was done to create subject-appropriate stimuli and to ensure that any eACC to the transition between modulated and unmodulated portions was not attributable to long-term loudness differences between them40,41. Behavioral thresholds, comfort levels and the current needed for each condition to obtain an equal loudness perception across conditions and subjects, were assessed prior to the EEG experiments (see “Methods” section). Threshold (Tunmod) and comfort (Cunmod) levels for the unmodulated pulse train were, on average across subjects, 45.1 dB re 1µA (range 39.3 to 51.8 dB re 1µA) and 51 dB re 1µA (range 46.4 to 56.1 dB re 1µA), respectively. Tunmod served as the minima of the 100% amplitude modulated pulse train. The comfort levels of the 100% AM pulse train (Cmod) were, on average across subjects, 51.3 dB re 1µA (range 47.1 to 56.1 dB re 1µA). The different MDs% were based on the percentage of the dynamic range (dB current) between Tunmod and Cmod, and loudness balancing was used to ensure that the ACC was evoked purely based on the difference in MD and not due to the difference in long-term loudness between the unmodulated and the modulated parts of a trial. During the loudness-balancing procedure (see “Methods” section), Cmod was loudness-balanced to Cunmod while the MD was kept fixed. Although there were individual differences in the Cmod compared to Cunmod (Fig. 1C), there was no significant group level effect of MD% (i.e. 0 to 100%) on the current needed to obtain equal loudness as determined by a one-way ANOVA (F(4,39) = 0.055 p = 0.994).
Artifact removal effectiveness for measuring ASSRs
Figure 2A shows the stimulation artifacts of a representative subject in the time domain when no artifact removal is applied. Due to the asymmetric artifact waveform the artifact also contains a component at the response frequency (Fig. 2B) which leads, if not properly removed, into a false-positive detection of an ASSR.
Artifact removal effectiveness was assessed based on the phase characteristics of the measured response. We measured in addition to the 40-Hz eASSR, eASSRs to three additional frequencies (34, 37, and 43 Hz) and with the same stimulation parameters as the 100% MD stimulus, i.e. stimulated at a maximum perceptual modulation depth (MD% = 100%) and loudness level. These are modulation frequencies have been shown to evoke ASSRs and eASSRs that originate from the same generator(s) as the 40-Hz (e)ASSR both in normal-hearing listeners42,43 and in CI users19,22. The rationale of using the phase characteristics to assess the effectiveness of artifact removal is based on the fact that the latency of the eASSR generator (i.e. the group delay) is identical to the phase slope (i.e. gradient of phase delay) when there is a linear relationship in phase across modulation frequencies. When using closely neighboring modulation frequencies to assess the phase slope, this slope will change accordingly to the latency of the generator(s) that is involved in generating the measured response16,44. The latency of the 34 to 43 Hz eASSR in CI users is around 40 ms13,19. However, if the recording is dominated by the stimulation artifacts the slope will be flat (i.e. a group delay of 0 ms), hence the recorded response does not reflect a neural response but that of the CI stimulation artifact.
Stimulation artifacts could be removed by means of linear interpolation in eight out of ten subjects but only for the contralateral recording electrodes. The latency of the ipsilateral response to the CI recording electrodes was 0 ms, indicating that the artifact could not be removed from these channels (not shown). In the following we only report on the recording electrodes positioned contralateral to the CI and referenced to Cz. Figure 2C,D shows the phase and amplitude characteristics of the obtained responses after artifact removal. Linear interpolation, with a maximum duration, was unable to remove the stimulation artifacts in subjects S4 and S6, resulting in a zero slope (i.e. the artifact duration was longer than the interpolation length). The eASSR strength of S4 was just above the noise floor, which was not the case for S6 (Fig. 2C). The average eASSR magnitude of all artifact-free and significant responses was 0.47 µV (SD = 0.41 µV, range = 0.10 to 1.52 µV). The phase-frequency functions of those responses had an average slope of 14.47°/Hz (Fig. 2C). The corresponding latencies were on average 40.2 ms (SD = 8.9 ms), which is similar to those of CI users stimulated with pulse trains around 500 pps42,43 and to latencies obtained from normal-hearing listeners42,43. Furthermore, the phases of the 40-Hz eASSRs in the modulation depth experiment were, for these eight subjects, consistent across the different MDs% and not centered on a multiple of 180°, i.e. the phase of the stimulation artifact. This was not the case for subject S4 (Fig. 3A), from whose responses the artifact could not be removed. These results show that the 40-Hz eASSRs of these eight subjects were, after artifact removal, true neural responses that are not affected by the stimulation artifacts.
Effect of modulation depth on electrophysiological responses
Figure 3 and 4 show, respectively, the 40-Hz eASSR and eACC as a function of MD% for each subject. The 40-Hz eASSRs could be evoked in ~ 80% of the subjects for MDs% > 25% (Fig. 5A). 40-Hz eASSR magnitudes varied across subjects and showed either a stable or decreasing pattern with decreasing MD%. Although some individual patterns showed a decrease in response strength with decreasing MD%, there was no significant group level effect of MD% on the 40-Hz eASSR amplitude as determined by one-way ANOVA (F(3,23) = 0.167 p = 0.918). 40-Hz eASSR magnitudes were on average 0.37 µV (SD = 0.42 µV) for the 25% MD% condition, 0.45 µV (SD = 0.49 µV), for the 50% MD% condition 0.47 µV (SD = 0.52 µV), for the 75% MD% condition, and 0.56 µV (SD = 0.56 µV) for the 100% MD% condition.
The morphology of the eACC varied across participants and conditions (Fig. 4) and eACCs could only be evoked in ~ 80% of the subjects for the 100% MD: for all the other MDs fewer than 30% of the subjects had a significant response (Fig. 5A). N1 magnitude was on average − 1.35 µV (range − 3.1 to 0.15 µV) and its latency was on average 135.9 ms (range 75.0 to 193.5 ms). The P2 magnitude was on average 1.31 µV (range 0.52 to 2.19 µV) and its latency was on average 226.5 ms (range 138.1 to 279.5 ms).
There was no significant across-subject correlation between the ASSR magnitude and the N1 and P2 magnitude or N1 and P2 latency. This indicates that although both measures are affected by the of the MD, they do not covary. Subject S10 for example has, although prolonged latencies, classical ACC waveforms but very low ASSR magnitudes; in contrast, S7 and S8 have ASSR magnitudes within the normal range of those reported in the literature19,42 but non-classical ACC waveforms.
Association between dynamic range and electrophysiological response strength
To investigate if a larger dynamic range results in a better representation of the TEM in the neural code, hence a larger electrophysiological response, we assess whether the modulation depth in dB current (MDdB) was associated with the strength of both the 40-Hz eASSR and eACC. We found that MDdB correlated significantly with the ASSR magnitude for the 50% (r(5)pearson = 0.89, p = 0.007), and 100% modulation condition (r(5)pearson = 0.83, p = 0.021), but not for the 25% (r(3)pearson = 0.82, p = 0.091) and 75% modulation condition (r(5)pearson = 0.69, p = 0.086) (Fig. 5B). Furthermore, the MDdB of the 100% modulation condition was significantly correlated with the P2 amplitude (r(5)pearson = 0.86, p = 0.013) (Fig. 5C), but not with the N1 amplitude (r(5)pearson = -0.10, p = 0.83) or the N1 (r(5)pearson = 0.19, p = 0.69) and P2 (r(5)pearson = -0.9, p = 0.69) latencies. This indicates that both the 40-Hz eASSR magnitude as the P2 amplitude of the ACC are affected by the dynamic range used for stimulation.
Reliability of the electrophysiological responses
To gain insight in the reliability of the electrophysiological responses, we randomly divided the recordings of the 40-Hz eASSRs and eACCs into equal unique trials (a split-recording half-half) and found that the 40-Hz eASSR magnitude across all subjects and conditions highly correlated between the split-recordings (r(29)pearson = 0.99, p < 0.0001) (Fig. 6A). Furthermore, the difference in magnitude between the split-recordings was within the average across-subjects neural background noise, except for the recordings where the neural background noise of the specific recording exceeded that of the average group neural background level (Fig. 6B). For the eACC we only assessed the MD% 100% condition, since this condition resulted in almost all of the significant responses across subjects. There were only 6 out of 7 eACCs significant in the first split-recording and only 3 out of 7 in the second split-recording, hence further analysis was not possible. These results show that even half of the used trials result in very robust responses for the 40-Hz eASSr. However, the eACC requires more averages. One has to take into account when interpreting these results that the variability in the response magnitude across recordings is directly related to the neural background noise42 which normally decreases with a factor equal to the square root of the number of averages. For example, the average, neural background noise for the 40-Hz eASSR across subjects and conditions, increased from 42.7 to 63.3 nV when halving the number of averaged trials. The variability of the obtained responses when all trials are averaged is therefore less than those reported on the split-recordings, indicating that the responses reported here are robust.
Measuring the neural response to continuous electrical stimulation is inevitably corrupted by the large stimulation artifact in the recorded EEG signal, which is not only specific to CIs but also to other biomedical devices30. This is especially problematic when the neural response cannot be discriminated from the stimulation artifact, as is the case for eASSRs measured from CI users. The removal of stimulation artifacts from the EEG-recording is challenging especially when they result from stimulating at clinically relevant pulse rates, or higher, and in monopolar stimulation mode19,24,25,29,45,46. In order to enable artifact removal—i.e. reducing the artifact waveform distortion and duration—for these clinically relevant stimulation parameters, we used here a newly designed EEG recording system that operates at a sample rate that exceeds those of conventional EEG systems (i.e. at 262 kHz). Our results show that, by using this hyper-rate EEG system and applying linear interpolation, stimulation artifacts could effectively be removed from the EEG recording in the majority of the subjects when recording from locations contralateral to the CI. The maximum pulse rate that effectively can be used to remove the stimulation artifacts, when stimulating in monopolar mode and record the EEG with a conventional sample rate < 16 kHz, was 500 pps13,19,23,29. The advantage of the hyper-rate system, as used here, is that it limits the distortion of the artifact waveform30 and therefore shortens its duration, and hence enable the use of higher pulse rates when using the linear interpolation method for artifact removal.
Temporal envelope encoding in the auditory pathway is of importance for CI users since these are the main features that are transmitted by the CI4. The ability of a CI user to detect modulations in a signal are associated with better speech perception47,48. Furthermore, the processing of TEMs can depend on the stimulated neural ensembles, and disabling electrodes that elicit high MDTs has been shown to improve speech perception in noise12,13,14. Given that a large variation in TEMs processing of the neural ensembles located across the CI electrode array can be detrimental to speech perception, there is a potential for improvement based on fitting methods that take this variability into account. In the search of a clinically feasible method to determine TEM encoding we investigated how both the 40-Hz eASSR and the eACC are affected by MD%. We found that both the 40-Hz eASSR and eACC are affected by MD% but differently. Whereas the 40-Hz eASSR is only slightly affected by the MD%s as used, the eACC could only be elicited by a full modulation in the majority of subjects.
At present, it is unclear if the used MDs% are perceptually different from each other and how this affects the ASSR. Monoghan et al.49 for example, found that CI users, based on psychophysics, are insensitive to differences in modulation depth across a large part of the dynamic range. Nevertheless, the relatively stable patterns as a function of modulation depth as reported here have been also observed in normal-hearing humans when using acoustical stimulation50. Dimitrijevic et al.50 found that there is only a limited growth in ASSR strength with the increase of MD from 50 to 100% and similar results have been reported by Picton et al.43. Furthermore, the variation in 40-Hz ASSR as a function of MD is affected by age, with a shallower/absent growth for MDs > 40% with advancing age50. The comparison of the eASSR obtained in CI users with the ASSRs as obtained in normal-hearing people has to be interpreted with caution. Loudness growth functions differ markedly between acoustic- and electric stimulation; normal-hearing people have a compressive loudness growth function51 whereas CI users have a linear loudness growth51 that steeply increases after a specific knee point41. The relatively stable patterns as a function of modulation depth as observed here indicate that variations in the 40-Hz eASSR amplitude across the CI array, as reported by Gransier et al.13 probably reflect rather large differences in TEM encoding between the stimulated neural ensembles across the CI array, especially since large differences in MD—up to 75% of the dynamic range—did not result into measurable differences in eASSR amplitude in the present study.
Although the 40-Hz ASSR was present for most subjects and MDs, this was not the case for the eACC. Furthermore, there was no association between the eACC and the 40-Hz eASSR. This suggests that the responses reflect different mechanism in the auditory pathway. Whereas the 40-Hz eASSR is a phase-locked response and can only be evoked when there is phase-locking to the temporal envelope, the eACC is elicited by a change in stimulus characteristics. The ACC strength, evoked acoustically in the normal-hearing auditory pathway, has been shown to decrease with decreasing MD32 and has the same lowpass characteristic as the behavioral temporal modulation transfer function32. In contrast, the findings in the acoustically stimulated normal-hearing auditory pathway are not straightforward to translate to the eACCs elicited in the electrically stimulated deafened auditory pathway. One assumes, when acoustically stimulating the normal-hearing auditory pathway, that the mechanisms involved in processing TEMs are relatively equal across subjects. Therefore, by controlling for all other factors that could evoke an ACC—e.g. loudness and pitch—one can assess the ACC as a function of MD. However, this translation is not so straightforward in the case of CI recipients. When interpreting the eACC one has to consider that reduced or absent phase-locking can result in a neural signal that the brain interprets as different from an unmodulated signal, and that this difference can evoke an eACC. The eACC can thus be evoked when the neural encoding of the two stimuli is different, it does, however, not mean that the TEM is represented properly in the neural code, hence an absent or reduced 40-Hz eASSR. S1 and S10 are an example of such a potential effect. S1 has both 40-Hz eASSRs and ACC, whereas S10 has very small or absent 40-Hz eASSRs but eACCs that are about as large as those of S1. Furthermore, one has to consider that at an early stage loudness integration occurs at a timescale of about 7 ms52 compared to the overall-loudness perception which is typically 300 ms53 as assessed with the loudness balancing task used. In addition, eACCs have been measured to gaps as short as 5 ms54. It is therefore difficult to determine based on the protocol used if the eACCs measured were due to the first valley in the modulation or to the processing of several cycles of modulation, since both become less detectible with decreasing MD. Although most subjects reported that they heard the modulation during the experiment, it is not clear what triggered the eACC. Nevertheless, Mathew et al.35,36 successfully used the eACC to assess electrode discrimination, and as long as the alteration made between two alternating stimuli cannot be attributed to confounding factors, this can be a clinically relevant measure which is little troubled by the stimulation artifacts.
The electrophysiological measures used in the present study originate from regions in the auditory pathway beyond the periphery17,38 and are assumed to reflect the processing cascade of all neural ensembles involved in TEM encoding of the ascending auditory pathway up to generator of the neural response. It is therefore difficult to derive from these measures where in the ascending auditory pathway TEM encoding is affected. An important bottleneck in electrical stimulation of the auditory pathway is the electrode-neuron interface55 and there is indirect evidence that measures like the 40-Hz eASSR but also the MDTs as assessed behaviorally reflect the TEM encoding ability at the level of the electrode-neuron interface11,13. Electrophysiological measures from the periphery could potentially be complementary to the more central measures and can provide insight where in the auditory pathway TEM encoding is affected. Studies have shown that ECAPs can be obtained to each pulse of a modulated pulse trains both in animals56 and humans57. Jeng et al.56 found that the electrically-evoked compound action potential (eCAP) modulated response amplitudes (i.e. difference between the minimum and maximum eCAP amplitudes across a modulated cycle) show a compressive non-linear growth with increasing modulation depths, which is in line with the 40-Hz eASSR growth functions that we observed. Furthermore, Tejani et al.57 measured the eCAPs to AM pulse trains with high modulation rates (> 100 Hz) and found that the slope of the ECAP slope as a function of current used in the AM pulse train was correlated with the MDTs of the same stimuli. The combination of peripheral and more central electrophysiological measures can potentially provide more insight in the location of TEM encoding deficits in the electrically-stimulated auditory pathway.
Our results could, in addition to the assessment of TEM processing, potentially pave the way for the objective assessment of detection thresholds in CI users. Threshold determination is of importance for programming the CI sound processor for clinical use4. Nevertheless, this is challenging in CI recipients who are unable to give reliable subjective feedback, such as infants, young children, and adults who are intellectually challenged. Detection thresholds are, however, known to decrease with increasing pulse rate due to multi-pulse integration. The slope of this decrease as a function of pulse rate can be highly variable across subjects and stimulation sites11,58,59, and is associated with the neural health of the stimulated neural ensembles60. This makes it difficult to estimate the stimulation thresholds in CI users based on electrophysiologic measures that use low-rate stimuli, such as the eCAP and eABR58. The advantage of the eASSR is that one can modulate a high-rate carrier to obtain the electrophysiological response, and hence obtain the electrophysiological thresholds with the same pulse rate as used in the clinical device. Hofmann and Wouters22 and Van Eeckhoutte et al.61 both measured the 40-Hz eASSR magnitude as a function of current in bipolar mode and reported that the growth functions corresponded with loudness perception61 and that that the detection thresholds could be estimated from the growth functions22. Our results show that the 40-Hz eASSR can be obtained, free from stimulation artifacts when using a clinically-relevant pulse rate of 900 pps and monopolar stimulation. Furthermore, our results show a relative flat 40-Hz eASSR magnitude as a function of modulation depth, indicating that when using a modulation depth that corresponds to the dynamic range of the average CI user, one should be able to evoke 40-Hz eASSRs in most CI users without a large reduction of the response strength compared to using the maximal perceptual modulation depth. Taking this into account and given that ASSRs are used clinically to determine hearing thresholds of infants with a suspicion of hearing loss21, it should be feasible to determine detection thresholds to clinically-relevant stimulation pulse rates, stimulated in monopolar mode, by the means of the 40-Hz eASSR in adult CI users, when using the hyper-rate EEG system to record the EEG and linear interpolation for artifact removal.
All stimuli were generated in Matlab R2016b and were delivered directly to the implant by the means of a research interface, which consisted of a laptop with custom-written software interfacing with the Nucleus Implant Communicator (version 3) and connected to the implant through a programming device and an L34 research processor. The hardware and the Nucleus Implant Communicator were provided by Cochlear Ltd. The pulse trains used in all experiments were either unmodulated or amplitude modulated and consisted of symmetric biphasic cathodic-first pulses, with a phase width of 25 µs and an interphase gap of 8 µs. Pulse trains were presented at 900 pps to the most apical electrode (e22) in monopolar mode (i.e. both the extracochlear electrode on the casing and the extracochlear ball electrode were used as the return electrodes). The most apical electrode was chosen based on the results of Gransier et al.13 They evoked a 40-Hz eASSR with each stimulation electrode of the electrode array separately and found that, although the 40-Hz eASSR could be evoked in almost all CI users and from all CI electrodes, the most apical electrode had a variable 40-Hz eASSR amplitude across CI users. Furthermore, Luke et al.20 found that the 40-Hz eASSR amplitude is associated with the behavioral MDT (i.e. larger 40-Hz eASSR amplitudes correspond to better MDTs). Based on these results we considered the most apical stimulation electrode to be ideal to assess the association between the 40-Hz eASSR and the eACC.
Behavioral assessment of stimulation levels
Stimulation levels were determined behaviorally at the beginning of each experiment by using a 7-point categorical loudness scale (i.e. “inaudible”, “very soft”, “comfortably loud”, “loud”, “very loud”, and “unbearable”). First, the maximum comfort level for the unmodulated pulse train (Cunmod) was assessed by starting ~ 20 current units, which corresponds to roughly 3 dB below the threshold level of the participant’s clinical map, and the current was then gradually increased to obtain the most comfortable loudness level which is defined the current level prior to the transition between “comfortably loud” and “loud” on the categorical loudness scale. Second, the current was gradually decreased to determine the threshold level of the unmodulated pulse train (Tunmod). Tunmod was defined as the current level below which the participant could not perceive the stimulus anymore. Third, the comfort level of the 40-Hz 100% amplitude modulated stimulus (Cmod) was determined. The minimum of the modulation was fixed at Tunmod and current of the other pulses in the sequence were increased until Cmod was achieved. Cmod was determined the same way as Cunmod. The amplitude modulation of all modulated stimuli was sinusoidal on a linear current scale. Although, the behavioral levels were initially assessed in current levels, the currents reported here are in dB re 1 µA. Equation 1 and 2, as provided by Cochlear ltd, were used to calculate the current in dB re 1 µA from the current levels—as send to the programming device—for the CIC3 and CIC4 implants, respectively.
MDs (25, 50, 75, and 100%) were based on the dynamic range (i.e. 100% MD), which is defined as the difference between Cmod and Tunmod. The different MDs were based on the current (in dB). To minimize the effect of overall loudness differences between the unmodulated and modulated pulse trains on the ACC, the modulated pulse trains were loudness-balanced to the unmodulated pulse train. This procedure was done for each modulation depth separately. During the loudness-balancing task, a two-down, one-up procedure was used and the participant had to indicate which presentation was louder (either the unmodulated or the modulated stimulus) in a two-alternative forced choice paradigm. Step sizes of one or two current units were used depending on the discrimination ability of the participant and the MD was kept constant across trials. The loudness balancing procedure was stopped after eight reversals and the mean of the last six reversals was used as the loudness balanced level.
The electrophysiological measurements consisted of two parts. First, we recorded the EEG to amplitude-modulated pulse trains with modulation frequencies of 34, 37, 40, and 43 Hz. This was done to evaluate the effectiveness of the offline-applied, artifact removal method. The rationale behind these measurements is that the group delay of the generator(s) from which the ASSR originate is constant for closely spaced modulation frequencies42,43. When the artifact is effectively removed and/or the neural response dominates the EEG recording a group delay around 40 ms is expected19,42, whereas a group delay of 0 ms expected if the recordings are dominated by the stimulation artifact19,22. In the following we refer to this part of the EEG experiment as the group delay experiment. We measured the EEG to the different modulated pulse trains at a 100% MD. This MD was chosen since the artifact component at the modulation frequency increases with increasing MD, so by using a 100% modulation we were able to evaluate artifact removal for the most extreme condition per subject. Stimulation levels were subject-specific and were those that were determined during the behavioral assessment of the stimulation levels. The stimulus consisted of 300 epochs each with a duration of 1.024 s, and modulation frequencies and pulse rates were adjusted so that each epoch included an integer number of cycles/pulses, only the rounded modulation frequencies/pulse rates are reported. A trigger was sent at the start of each epoch from the programming device to synchronize the stimulation and recording.
Second, we recorded the EEG to the stimuli that were used to assess the effect of MD on the 40-Hz ASSR and the ACC. A single trial consisted of a 2.024 s unmodulated pulse train and a 2.024 s 40-Hz AM pulse train. The MD of the modulated part was changed across conditions (i.e. 25, 50, 75, and 100%), and the stimulation levels were set to those as determined during the behavioral assessment of the stimulation levels. 100 trials of a specific MD were concatenated and presented in one block, and a trigger was sent at the start of each trial from the programming device to synchronize the stimulation and recording. Two blocks of each MD were presented in random order during a session. Subject S6 perceived the loudness balanced levels as too loud during the EEG experiments. Although stimulation levels were lowered and the EEG experiment was carried out, she was excluded from the analysis since the results were potentially cofounded by loudness cues. For this reason, S6 is only included in the analysis of the first EEG experiment in the “Results” section. In the following we refer to this part of the EEG experiment as the modulation depth experiment.
EEG was recorded with an 8-channel Biosemi ActiveTwo Hyper-Rate EEG recording system designed and built to our specifications. This system is based on the Biosemi ActiveTwo EEG-recording system but with a sample rate of 262.144 kHz/channel and with a built-in analog third-order antialiasing filter having a −3 dB point at 50 kHz. We used Ag/AgCl active recording electrodes to record the EEG. The recording electrodes were placed at the subject’s head using an 8-channel cap according to a 10–20 system62 layout. The position of the recording electrodes on the ipsilateral to the CI site differed across subjects due to the location of the CI, but were always placed in a close proximity to the mastoid, if possible. Individual differences in placement were the result of the location of the RF receiver of the CI, since no recording electrodes could be placed there due to the presence of the research sound processor. The results reported are based on recording electrodes that are placed in close proximity of the left and right mastoid (the recording electrodes contralateral to the CI were always P10 or P9) and referenced to Cz. This electrode configuration was chosen since it optimally captures the electrical potential originating from 40-Hz ASSR generator(s)63.
All EEG recordings were made in a Faraday cage, an electrically shielded sound booth, where participants sat in a comfortable chair. To minimize tension in the muscles supporting the head, the head and neck were supported by the chair and occasionally by a cushion. To reduce artifacts caused by movements, participants were asked to move as little as possible during the recording. A silent movie with subtitles was played to ensure that the attentional state was similar in all conditions and for all participants. This approach was identical to that of Gransier et al.13,19.
All off-line signal processing was done in Matlab (version 2016b)64. CI-stimulation artifacts were first removed from the raw EEG signal by means of linear interpolation between a prestimulation pulse sample and a poststimulation pulse sample. The prestimulation pulse sample was set at 100 µs and the poststimulation pulse sample at 900 µs after the start of each stimulation pulse. After linear interpolation, the time signal of each recording electrode was high-pass filtered using a 2nd order Butterworth high-pass filter with a cutoff frequency of 2 Hz, to remove any DC component in the recordings.
For the ASSR analysis we divided each time signal of each recording into individual epochs, each with a length of 1.024 s for the group delay experiment and 2.048 s for the modulation depth experiment, based on the triggers. The EEG response to the unmodulated part of each trial in the modulation depth experiment was omitted from the analysis. Epochs of the different recording blocks in the modulation depth experiment were combined, resulting in a total of 200 epochs per MD. Five percent of the total number of epochs with the highest peak to peak amplitude were removed from the recordings to minimize the effect of the physiologic and extraphysiologic artifacts containing recording epochs. A Fast Fourier Transform was used to calculate the complex frequency spectrum of each epoch, resulting in a frequency resolution of 0.98 and 0.49 Hz for the group delay and modulation depth experiment, respectively. To remove the common noise across electrodes and to optimally capture the dipoles originating from the 40-Hz ASSR generator(s), the different channels and electrodes were referenced to the electrode positioned at Cz. Referencing was done by subtracting the complex frequency spectrum of the reference electrode from the complex frequency spectrum of each channel and the recording electrode. To compensate for the filter effects on the magnitude of the response, the inverse gain of the high-pass filter was applied to the frequency spectrum of each epoch. For each epoch, the response power, amplitudes, and phases were obtained from the complex frequency spectrum corresponding to the modulation frequencies used during the experiment (i.e. the response spectrum). The mean response amplitude and phase were computed by vector averaging the complex response spectrum across epochs. The neural background noise was calculated as the standard deviation over epochs divided by the square root of the number of epochs42. The Hotelling T2 was used, for each channel, to determine whether the synchronized activity (i.e. the measured response) differed significantly from the nonsynchronized neural background activity. This test compares the average real and imaginary components of the response spectrum with the variability across epochs of the response spectrum22,65. We derived the group delay (i.e. the latency of the generator) in the group delay experiment from the response phase slope across the modulation frequencies.
For the ACC analysis, we referenced the raw-EEG time signals after blanking to Cz and divided each referenced time signal into individual trials based on the triggers. Trials of the different recording blocks were combined, resulting in a total of 200 trials per MD. Five percent of the total number of trials with the highest peak to peak amplitude were removed from the recordings to minimize the effect of the physiologic and extraphysiologic artifacts containing recording trials. A low-pass filter (eegfilt, from EEGLAB) with a cutoff frequency of 14 Hz was then applied for analyzing the ACCs to the change from the constant to the modulated part of the trial. The Golding et al.66 implementation of the Hotelling T2 test was used to determine if an ACC was present, and peaks and latencies were determined using a semi-automatic procedure. We then analyzed the N1 and P2 peak of the ACC separately since both are assumed to originate from different generators and are associated with different auditory processes67,68. All other statistical analyses and figures were done in R (version 3.5.3)69 and a significance level of 5% was used.
Ten adult native Flemish-Dutch-speaking CI users took part. All had a history of long-term hearing impairment with an average CI use of 4.3 years. All participants had a device from Cochlear Ltd. and were followed up at the ear, nose, throat clinic and the Multidisciplinary Center for Logopedics and Audiology (MUCLA) of the University Hospital in Leuven, Belgium. Participant details are shown in Table 1. This study was approved by the Medical Ethics Committee of the University Hospital in Leuven (Approval number: B322201524931) and all methods were carried out in accordance with the relevant guidelines and regulations. Written informed consent was obtained from all participants before testing.
Moore, D. R. & Shannon, R. V. Beyond cochlear implants: Awakening the deafened brain. Nat. Neurosci. 12, 686–691 (2009).
Drullman, R., Festen, J. M. & Plomp, R. Effect of reducing slow temporal modulations on speech reception. J. Acoust. Soc. Am. 95, 2670–2680 (1994).
Shannon, R. V., Zeng, F., Kamath, V., Wygonski, J. & Ekelid, M. Speech recognition with primarily temporal cues. Science 270, 303–304 (1995).
Wouters, J., Mcdermott, H. J. & Francart, T. Sound coding in cochlear implants. IEEE Signal Process. Mag. 32, 67–80 (2015).
Friesen, L. M. et al. Speech recognition in noise as a function of the number of spectral channels: Comparison of acoustic hearing and cochlear implants. J. Acoust. Soc. Am. 1150, 1150–1163 (2001).
Fishman, K. E., Shannon, R. V. & Slattery, W. H. Speech recognition as a function of the number of electrodes used in the SPEAK cochlear implant speech processor. J. Speech Lang. Hear. Res. 40, 1201–1215 (1997).
Garnham, C., O’Driscoll, M., Ramsden, R. & Saeed, S. Speech understanding in noise with a Med-El COMBI 40+ cochlear implant using reduced channel sets. Ear Hear. 23, 540–552 (2002).
Shannon, R. V., Cruz, R. J. & Galvin, J. J. Effect of stimulation rate on cochlear implant users’ phoneme, word and sentence recognition in quiet and in noise. Audiol. Neurotol. 16, 113–123 (2011).
Berg, K. A. et al. Speech recognition as a function of the number of channels in perimodiolar electrode recipients. J. Acoust. Soc. Am. 145, 1556–1564 (2019).
Croghan, N. B. H., Duran, S. I. & Smith, Z. M. maximal speech intelligibility re-examining the relationship between number of cochlear implant channels and maximal speech. J. Acoust. Soc. Am. 142, 537–543 (2017).
Pfingst, B. E. et al. Importance of cochlear health for implant function. Hear. Res. 322, 77–88 (2015).
Garadat, S. N., Zwolan, T. A. & Pfingst, B. E. Across-site patterns of modulation detection: Relation. J. Acoust. Soc. Am. 4030, 4030–4041 (2012).
Gransier, R., Luke, R., Wieringen, A. V. & Wouters, J. Neural modulation transmission is a marker for speech perception in noise in cochlear implant users. Ear Hear. 41, 591–602 (2020).
Garadat, S. N., Zwolan, A. & Pfingst, B. E. Using temporal mdulation sensitivity to select stimulation sites for processor MAPs in cochlear implant listeners. Audiol. Neurotol. 18, 247–260 (2013).
Zhou, N. & Pfingst, B. E. Effects of site-specific level adjustments on speech recognition with cochlear implants. Ear Hear. 35, 30–40 (2014).
Picton, T. W., John, M. S., Dimitrijevic, A. & Purcell, D. Human auditory steady-state responses. Int. J. Audiol. 42, 177–219 (2003).
Luke, R., Vos, A. D. & Wouters, J. NeuroImage source analysis of auditory steady-state responses in acoustic and electric hearing. Neuroimage 147, 568–576 (2017).
Herdman, A. T. et al. Intracerebral sources of human auditory steady-state responses. Brain Topogr. 15, 69–86 (2002).
Gransier, R. et al. Auditory steady-state responses in cochlear implant users: Effect of modulation frequency and stimulation artifacts. Hear. Res. 335, 149–160 (2016).
Luke, R., Deun, L. V., Hofmann, M., Wieringen, A. V. & Wouters, J. Assessing temporal modulation sensitivity using electrically evoked auditory steady state responses auditory steady state responses. Hear. Res. 324, 37–45 (2015).
Luts, H., Desloovere, C. & Wouters, J. Clinical application of dichotic multiple-stimulus auditory steady-state responses in high-risk newborns and young children. Audiol. Neurotol. 11, 24–37 (2006).
Hofmann, M. & Wouters, J. Improved electrically evoked auditory steady-state response thresholds in humans. J. Assoc. Res. Otolaryngol. 13, 573–589 (2012).
Deprez, H. et al. Characterization of cochlear implant artifacts in electrically evoked auditory steady-state responses. Biomed. Signal Process. Control 31, 127–138 (2017).
Deprez, H. et al. Independent component analysis for cochlear implant artifacts attenuation from electrically evoked auditory steady-state response measurements. J. Neural Eng. 15, 016006 (2018).
Deprez, H. et al. Template subtraction to remove CI stimulation artifacts in auditory steady-state responses in CI subjects. IEEE Trans. Neural Syst. Rehabil. Eng. 25, 1322–1331 (2017).
Luke, R. & Wouters, J. Kalman filter based estimation of auditory steady state response parameters. IEEE Trans. Neural Syst. Rehabil. Eng. 25, 196–204 (2017).
Attina, V. et al. A new method to test the efficiency of cochlear implant artifacts removal from auditory evoked potentials. IEEE Trans. Neural Syst. Rehabil. Eng. 25, 2453–2460 (2017).
Hofmann, M. & Wouters, J. Electrically evoked auditory steady state responses in cochlear implant users. J. Assoc. Res. Otolaryngol. 11, 267–282 (2010).
Bahmer, A., Pieper, S. & Baumann, U. Evaluation of an artifact reduction strategy for electrically evoked auditory steady-state responses: Simulations and measurements. J. Neurosci. Methods 296, 57–68 (2018).
Lio, G., Thobois, S., Ballanger, B., Lau, B. & Boulinguez, P. Clinical Neurophysiology Removing deep brain stimulation artifacts from the electroencephalogram: Issues, recommendations and an open-source toolbox. Clin. Neurophysiol. 129, 2170–2185 (2018).
Hine, J. & Debener, S. Late auditory evoked potentials asymmetry revisited. Clin. Neurophysiol. 118, 1274–1285 (2007).
Han, J. H. & Dimitrijevic, A. Acoustic change responses to amplitude modulation: A method to quantify cortical temporal processing and hemispheric asymmetry. Front. Neurosci. 9, 1–15 (2015).
He, S. et al. Gap detection measured with electrically evoked auditory event—Related potentials and speech-perception abilities in children with auditory neuropathy spectrum disorder. Ear Hear. 34, 733–744 (2013).
Liang, C., Houston, M. & Samy, R. N. Cortical processing of frequency changes reflected by the acoustic change complex in adult cochlear implant users. Audiol. Neurotol. 23, 152–164 (2018).
Mathew, R. et al. Development of electrophysiological and behavioural measures of electrode discrimination in adult cochlear implant users. Hear. Res. https://doi.org/10.1016/j.heares.2018.07.002 (2018).
Mathew, R. et al. Objective assessment of electrode discrimination with the auditory change complex in adult cochlear implant users. Hear. Res. 354, 86–101 (2017).
Abbas, P. J. & Brown, C. J. Assessment of responses to cochlear implant stimulation at different levels of the auditory pathway. Hear. Res. 322, 67–76 (2015).
Han, J.-H. & Dimitrijevic, A. Acoustic change responses to amplitude modulation in cochlear implant users: Relationships to speech perception. Front. Neurosci. 14, 1–11 (2020).
Pfingst, B. E., Burkholder-juhasz, J. A., Xu, J. & Thompson, J. S. Across-site patterns of modulation detection in listeners with cochlear implants. J. Acoust. Soc. Am. 1231054, 1054–1062 (2008).
Fraser, M. & McKay, C. M. Temporal modulation transfer functions in cochlear implantees using a method that limits overall loudness cues. Hear. Res. 283, 59–69 (2012).
Mckay, C. M. & Henshall, K. R. Amplitude modulation and loudness in cochlear implantees. J. Assoc. Res. Otolaryngol. 11, 101–111 (2010).
Gransier, R., van Wieringen, A. & Wouters, J. Binaural interaction effects of 30–50 Hz auditory steady state responses. Ear Hear. 38, e305-325 (2017).
Picton, T. W., Skinner, C. R., Champagne, S. C. & Kellett, A. J. C. Potentials evoked by the sinusoidal modulation of the amplitude or frequency of a tone. J. Acoust. Soc. Am. 82, 165–178 (1987).
Regan, D. Some characteristics of average steady-state and transient responses evoked by modulated light. Electroencephalogr. Clin. Neurophysiol. 20, 238–248 (1966).
Deprez, H., Gransier, R., Hofmann, M., Wouters, J. & Verhaert, N. Development and validation of a method to record electrophysiological responses in direct acoustic cochlear implant subjects. Hear. Res. 370, 217–231 (2018).
Mina, F., Attina, V., Duroc, Y., Veuillet, E. & Truy, E. Auditory steady state responses and cochlear implants: Modeling the artifact-response mixture in the perspective of denoising. PLoS ONE https://doi.org/10.1371/journal.pone.0174462 (2017).
Fu, Q. J. Temporal processing and speech recognition in cochlear implant users. NeuroReport 13, 1635–1639 (2002).
Luo, X., Fu, Q. J., Wei, C. G. & Cao, K. L. Speech recognition and temporal amplitude modulation processing by Mandarin-speaking cochlear implant users. Ear Hear. 29, 957–970 (2008).
Monaghan, J.J.M., Carlyon, R.P. & Deeks, J. M. Amplitude modulation depth discrimination by cochlear implant users. in Conference on Implantable Auditory Prostheses, 114 (2019).
Dimitrijevic, A., Alsamri, J., John, M. S., Purcell, D. & George, S. Human envelope following responses to amplitude modulation: Effects of aging and modulation depth. Ear Hear. https://doi.org/10.1097/AUD.0000000000000324 (2016).
Zeng, F.-G. & Shannon, R. V. Loudness-coding mechanisms inferred from electric stimulation of the human auditory system. Science 264, 564–566 (1994).
McKay, C. M. & McDermott, H. J. Loudness perception with pulsatile electrical stimulation: The effect of interpulse intervals. J. Acoust. Soc. Am. 104, 1061–1074 (1998).
Viemeister, N. F. & Wakefield, H. Temporal integration and multiple looks. J. Acoust. Soc. Am. 90, 858–865 (1991).
Pratt, H., Bleich, N. & Mittelman, N. The composite N 1 component to gaps in noise. Clin. Neurophysiol. 116, 2648–2663 (2005).
Bierer, J. A. Probing the electrode—Neuron interface with focused cochlear implant stimulation. Trends Amplif. 14, 84–95 (2010).
Jeng, F., Abbas, J., Brown, J. & Miller, A. Electrically evoked auditory steady-state responses in a guinea pig model: Latency. Audiol. Neuro-otol. 13(3), 161–171. https://doi.org/10.1159/000112424 (2008).
Tejani, V. D., Abbas, P. J. & Brown, C. J. Relationship between peripheral and psychophysical measures of amplitude modulation detection in cochlear implant users. Ear Hear. 38, e268–e284 (2017).
McKay, C. M., Chandan, K., Akhoun, I., Siciliano, C. & Kluk, K. Can ECAP measures be used for totally objective programming of cochlear implants?. J. Assoc. Res. Otolaryngol. 14, 879–890 (2013).
Zhou, N., Xu, L. & Pfingst, B. E. Characteristics of detection thresholds and maximum comfortable loudness levels as a function of pulse rate in human cochlear implant users. Hear. Res. 284, 25–32 (2012).
Pfingst, B. E. et al. Detection of pulse trains in the electrically stimulated cochlea: Effects of cochlear health. J. Acoust. Soc. Am. 3954, 3954–3968 (2011).
Van Eeckhoutte, M., Wouters, J. & Francart, T. Electrically-evoked auditory steady-state responses as neural correlates of loudness growth in cochlear implant users. Hear. Res. 358, 22–29 (2018).
Jasper, H. H. The ten twenty electrode system of the international federation. Electroencephalogr. Clin. Neurophysiol. 10, 370–375 (1957).
Goossens, T., Vercammen, C., Wouters, J. & van Wieringen, A. Aging affects neural synchronization to speech-related acoustic modulations. Front. Aging Neurosci. 8, 1–16 (2016).
The MathWorks Inc. MatLab 2016B. Natick, Massachusetts, United States. (2016).
Hotelling, H. The generalization of the student’s ratio. Ann. Math. Stat. 2, 360–378 (1931).
Golding, M., Dillon, H., Seymour, J. & Carter, L. The detection of adult cortical auditory evoked potentials (CAEPs) using an automated statistic and visual detection. Int. J. Audiol. 48, 834–842 (2009).
Näätänen, R. & Picton, T. The N1 wave of the human electric and magnetic response to sound: A review and an analysis of the component structure. Psychophysiology 24, 375–425 (1987).
Crowley, K. E. & Colrain, I. M. A review of the evidence for P2 being an independent component process: Age, sleep and modality. Clin. Neurophysiol. 115, 732–744 (2004).
R Core Team. R: A language and environment for statistical computing. R Foundation for Statistical Computing. Vienna, Austria. https://www.R-project.org/. (2019).
All CI users that participated in the research are gratefully acknowledge for their time and effort. Wouter David is gratefully thanked for his help during the data collection. Ann Dierckx is thanked for her help with the recruitment of the participants. Michael Hofmann, Hanne Deprez, Franҫois Guérit, John. C. Middlebrooks, and Matt Richardson are thanked for the helpful discussions. This work was funded by a Wellcome Trust Collaborative Award in Science RG91976 to RPC, John C. Middlebrooks, and JW. Also support from Flanders Innovation & Entrepreneurship through the VLAIO research grant HBC.2019.2373 with Cochlear is acknowledged.
The authors declare no competing interests.
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Gransier, R., Carlyon, R.P. & Wouters, J. Electrophysiological assessment of temporal envelope processing in cochlear implant users. Sci Rep 10, 15406 (2020). https://doi.org/10.1038/s41598-020-72235-9
This article is cited by
Electrophysiological and Psychophysical Measures of Temporal Pitch Sensitivity in Normal-hearing Listeners
Journal of the Association for Research in Otolaryngology (2022)
Stimulus-evoked phase-locked activity along the human auditory pathway strongly varies across individuals
Scientific Reports (2021)
Using Interleaved Stimulation to Measure the Size and Selectivity of the Sustained Phase-Locked Neural Response to Cochlear Implant Stimulation
Journal of the Association for Research in Otolaryngology (2021)