Aqueous copper bioavailability linked to shipwreck-contaminated reef sediments

Abstract

Pollution from the grounding or sinking of ships can have long lasting effects on the recovery and dynamics of coastal ecosystems. Research on the impact of copper (Cu) pollution from the 2011 MV Rena shipwreck at the Astrolabe Reef (Otaiti), New Zealand, 5 years after the grounding, followed a multi-method and multi-disciplinary approach. Three independent measures of aqueous Cu using trace-element-clean-techniques substantiate the presence of high total, total dissolved (<2 µm) and elevated bioavailable Cu in the water column immediately above the aft section of the wreck where the highest sedimentary load of Cu was located. Intermittently elevated concentrations of strong Cu-binding ligands occurred in this location, and their binding strength was consistent with ligands actively produced by organisms in response to Cu induced stress. The recruitment of benthic invertebrates was modified at the high-Cu location. Taxonomic groups usually considered robust to pollution were restricted to this site (e.g. barnacles) or were the most abundant taxa present (e.g. foraminifera). Our results demonstrate that Cu-contaminated sediments can impose a persistent point source of Cu pollution in high-energy reef environments, with the potential to modify the composition and recovery of biological communities.

Introduction

Between 2004 and 2014, 1,271 ships were lost at sea1. The causes may have included collision, adverse weather, loss of stability due to cargo movement or rupture of cargo tanks, explosions, uncontrollable fire, piracy, inadequate vessel maintenance and crew negligence or incompetence. While the environmental effects and legacies of most lost ships are unknown, contamination and subsequently environmental degradation are certain to occur. Metals and other potential contaminants, both organic and inorganic, are present in almost every part of a modern ship, including antifouling paints, electrical and electronic equipment, the hull and other structural components and sacrificial anodes together with fuels, lubricating and hydraulic fluids2. For cargo ships, the range of potential contaminants is greater still because these vessels can transport a variety of commercial and industrial chemicals and materials, raw minerals, oils, paints, plastics, manufactured goods, agricultural and horticultural produce, and personal belongings.

Vessels are typically lost in deep water where the costs and practicalities of salvage or monitoring are prohibitive, or they ground on coastlines of nations where environmental regulations are such that monitoring is limited or non-existent3. Occasionally, shipwrecks do occur on coastlines where there are public or governmental expectations around gaining an understanding of the environmental consequences of maritime casualties. However, unless a wreck occurs in exceptionally benign or accessible waters, it can be difficult to apply the methods that would normally be used to assess pollution and environmental impacts. As such, the ecological consequences of most shipwrecks are unknown.

One example of a relatively accessible shipwreck is the MV Rena4, which grounded and sank in 2011 at Otaiti (Astrolabe Reef; Fig. 1), in New Zealand’s Bay of Plenty. The sinking of the MV Rena generated headlines around the world and has been widely reported as New Zealand’s ‘worst maritime environmental disaster’5. Potentially because of the rarity of large shipwrecks in New Zealand’s recent maritime history, or because of New Zealand’s “clean green” image, the impacts of the MV Rena on Otaiti, both physical and chemical (the latter determined through analysis of sediments and biota6,7,8), have been remarkably well documented8. Otaiti lies 25 km offshore from Tauranga, one of New Zealand’s busiest ports. The reef is a high-energy environment, with a mean annual significant wave height of 1.19 m, with significant wave heights of 5.5 m occurring at a ~6-year Annual Return Interval9. Otaiti is a pinnacle of rock, which rises from a depth of around 70 m with a small section of reef (15 to 25 m2) breaking the water’s surface between mid and low tide. The reef has a base circumference of about 1 km and covers an estimated 461,587 m2 of seafloor. The major components of the shipwreck lie at depths ranging from −3 m to −60 m (Fig. 2). These physical and environmental factors have made it challenging to conduct both salvage and environmental monitoring activities. An extended salvage and recovery effort did much to remove contaminated reef sediments and wreckage8, yet a legacy of sediment contamination remains. Dempsey, et al.6 demonstrated both the contaminant legacy of the Rena and the usefulness of Diffuse Gradients in Thin Film (DGT) passive samplers for identifying and locating contaminants. Perhaps of greatest interest in trying to understand the long-term chemical and ecological impacts of the Rena is the fate of some 7 to 12 tonnes of granulated Cu (clove grade)2,4,5,6,7,8,10 which remain trapped beneath the wreck.

Figure 1
figure1

Map of the Bay of Plenty showing the location of the MV Rena on Otaiti (Astrolabe Reef),Okarapu (Control site), Motiti Island and Tauranga.

Figure 2
figure2

Chart of Otaiti showing the locations of water sampling and DGT deployments (discs) and settlement plate deployments (squares) along the 25 m depth contour. The Cu concentration measured in reef sediments is shown by the coloured cylinders (data from Ross, et al.7). Elongate remnants of the wreck lie on the central reef (south of settlement plate A), overlap with the northeast corner of the reef and lie parallel to its northeastern edge.

Aquatic pollutants, including Cu, have the potential to adversely influence the recovery of marine ecosystems through sub-lethal or lethal effects on resident communities11,12,13 or by altering the rates or locations at which recruitment of early life stages occurs14. This latter process can happen through several mechanisms. One is that the free-swimming larvae of benthic species may use water or substrate chemistry to select a settlement location, thereby selecting against contaminated substrate14. Alternatively, recruitment may occur despite differences in substrate chemistry (or that of the surrounding water), but subsequent survival rates diminish due to environmental or chemical differences, or through chemistry-dependent changes in (biological) species interactions14,15.

In order for Cu to be harmful and toxic, it needs to be present in a bioavailable form to enter the body of an exposed organism and interact with the surface or interior of their cells16. According to the literature17,18 the bioavailability of Cu is primarily related to the labile inorganic Cu fraction (Cu’), consisting of free Cu ions (Cu2+) and Cu complexed to inorganic ligands (CuXIN), rather than the total ([CuT]) or total dissolved Cu concentration ([dCuT]) in a system19,20,21. Some forms of organically complexed Cu are, however, also considered bioavailable22, but it is generally accepted that Cu’ represents the most readily bioavailable and thus toxic form of Cu to marine organisms. Consequently, the labile inorganic Cu fraction (Cu’) is a reasonable indicator of Cu bioavailability and is thus hereinafter referred to as bioavailable Cu (Cu’). The aquatic lifetime of bioavailable Cu (Cu’) (sum of Cu2+ and CuXIN) is considered low due to organic Cu-complexation (CuL) processes (>99%)11, but minor amounts of free Cu2+ ions and labile inorganic and organic Cu complexes can still adversely affect exposed organisms. Furthermore, the uptake of Cu’ by organisms will cause the dissociation of CuL due to the perturbation of the equilibrium between CuL and its products (Cu2+ +L). Additionally, ligands can be oxidised microbiologically or photo-chemically23, thereby changing the relationship between Cu concentration, speciation (i.e. chemical form) and toxicity.

Given the complex interplay between Cu speciation, environmental conditions and toxic effects, it was deemed necessary to expand on the work previously conducted at Otaiti6 to examine the aquatic speciation of Cu in the water column and the spatial scale at which water chemistry was affected (site C, Fig. 2)6. This study set out to assess the extent of water column Cu contamination at Otaiti, ascertain its bioavailability, and explore, using settlement plates, the effects of Cu contamination on the recruitment of benthic invertebrates14,24,25. A multi-method approach was implemented in order to obtain an integrated picture and provide complementary data on the concentration, speciation, distribution, as well as bioavailability of Cu in the working area (Fig. 3), thereby increasing the robustness of the results and conclusion. The multi-method analytical approach consisted of trace element clean sampling and analysis protocols of the Otaiti water column to collect Cu samples for High Resolution Sector Field Inductively Coupled Plasma Mass Spectrometery (HR-SF-ICP-MS) analysis, adsorptive cathodic stripping voltammetry (AdCSV)26 with salicylaldoxime (SA) as the complexing agent, and in-situ immersive measurements by diffusive gradients thin films (DGT) (see Section 6.1). HR-SF-ICP-MS was used to quantify total Cu (non-filtered, CuT) concentrations, while AdCSV was implemented to measure total dissolved Cu (filtered at 0.2 µm, dCuT) concentrations and Cu speciation parameters (e.g. CuXIN, Cu2+, L, and logK) of the collected water samples. DGTs were deployed to obtain a temporal integrated view of bioavailable Cu (CuDGT) in the system (see Section 6.1). We define the following terms for different components of Cu in our analysis: [] denote concentration, inorganically bound Cu (CuXIN), hydrated ‘free’ Cu ions (Cu2+), Cu-binding organic ligands (L), conditional stability constant of CuL complexes (logK), total Cu (non-filtered, CuT), total dissolved Cu filtered at 0.2 μm (dCuT), bioavailable Cu (Cu’), and DGT-labile Cu (Cu’+ dissociating Cu2+ from complexes with L) reported as CuDGT calculated using standard DGT theory6.

Figure 3
figure3

Conceptual figure of the three complementary analytical techniques used to analyse the concentration, speciation, and bioavailability of Cu in the study area of the MV Rena at Otaiti (Astrolabe Reef). Depicted AdCSV measurements reflect the Cu speciation analysis, not the dCuT evaluation.

Results

Cu concentrations and DGT measurements

The results of the aqueous [Cu] measurements are given in Table 1.

Table 1 Averaged total (n = 2), total dissolved (n = 2) and DGT-labile (n = 4) Cu concentrations in Otaiti and Okarapu Reef (control site) water samples collected over two sampling campaigns on 15–16th and 22–23rd June, 2016.

The [CuT], [dCuT] and [CuDGT] fractions varied coherently across the sample set (Table 1; Fig. 4) with markedly higher Cu concentrations encountered at the centre site. The results of these measurements were generally consistent with the known hierarchy of detection between techniques27 and indicate that coarse colloids and particles with diameters >0.2 μm were involved in Cu adsorption and mobilisation, driving the exceptionally large variability seen in [CuT] between the sampling campaigns at sites C1-3 (Table 1). We suggest that the dynamic variability in the concentration of colloidal/particulate Cu in these coastal settings also led to disparities between samples collected contemporaneously for CuT and dCuT. These disparities were evident at sites away from the major contamination plume where concentrations of suspended Cu-particles were at their highest (C1-3; Fig. 2, Table 1).

Figure 4
figure4

Averaged [CuT] determined by HR-SF-ICP-MS, [dCuT] determined by AdCSV in water samples collected in June 2016, and [CuDGT] determined from multi-day DGT deployments at Otaiti and Okarapu Reef (control site) in June 2016. Error bars represent the ±1 σ values for measurements carried out on two separate days (i.e. the inter-sample variability rather than analytical errors). [CuDGT] values are calculated from the average of four DGT Chelex-100 probes deployed between three and four days (n = 4). Dashed lines show the Australian and New Zealand Environment and Conservation Council75 water quality guidelines for total dissolved Cu concentrations ([dCuT]) to protect 99–80% of species.

Despite predictable differences between techniques, the overall trend between sites was captured by all three methods. In particular, the Centre sites, located in the vicinity of the Cu deposit, were the most contaminated, consistent with expectations based on previous site assessments7 which documented extremely high Cu sediment loads (up to 780 g kg−1) in this location (Fig. 2). Clearly, entrainment of this sediment by wave action creates the release of dissolved Cu and the resuspension of Cu-bearing particles in the vicinity of the Rena debris (sites C1-3; Table 1).

The overall distributions of [CuT], [dCuT] and [CuDGT] reflected a pronounced, but localised contamination at the centre sites (C1-3; Figs 2,3), when compared to the Cu concentrations at the South, North and Control sites. This analysis demonstrates significant Cu enrichment in the water column at Otaiti, with a localised contamination in a relatively small area in the immediate vicinity of the Cu-contaminated sediments (Fig. 3).

DGT is a dynamic method which measures the Cu fraction capable of diffusing within the DGT hydrogel across a 0.45 µm polycarbonate filter membrane28,29, i.e. consisting of small colloids, nanoparticles and labile Cu-ligand complexes. Only Cu fractions, which dissociate and subsequently bind with the Chelex-100 chelating resin inside the DGT housing within the timeframe of the deployment contribute to the final measurement of [CuDGT]. This means that DGT measurements may be the most analogous to the steady-state bioavailable Cu30 in a given aquatic system, except where Cu is made bioavailable by direct ingestion of Cu particles (e.g. bivalves). The dynamic and time-integrated nature of DGT measurements contribute to the higher values of [CuDGT] compared to [dCuT]. DGT also has the advantage of avoiding artefacts arising from sampling and sample handling27, although care should still be taken at all stages of associated laboratory operations31. Because of the differences in dynamic features between techniques and the potential for analytical artefacts to arise, the multi-method approach to determining aquatic trace metal speciation27 adopted here allows us to characterise the system more fully.

The difference between [CuT] and [CuDGT] highlights the fact that a large fraction of [CuT] was accounted for by Cu-bearing particles with diameters >0.1 μm. The residual between [dCuT] and [CuDGT] is therefore likely to reflect the presence of partially-labile organic Cu complexes which contributed to the time-integrated DGT measurements. The results of the AdCSV Cu speciation measurements are given below and give appropriate context to this finding.

Cu speciation by AdCSV

Samples analysed by AdCSV showed the best fit to a one-ligand model and all titrations demonstrated the presence of one organic ligand class with remarkably uniform Cu-binding capacities of logK 11.6 ± 0.3 throughout the study area for both sampling periods, despite the highly dynamic nature of the reef environment.

The average conditional stability constant (logK) on the 16th of June was 11.5 ± 0.4 and 11.7 ± 0.3 on the 20th of June. Ligand concentrations ranged from as low as [L] = 10.3 ± 1.5 nM for the control station (Okarapu Reef) to 114.8 ± 17.8 nM for the stations adjacent of the MV Rena wreck (sites C1-3). The ligand concentrations were always in excess of the total dissolved Cu-concentrations (Fig. 5) but were markedly higher on the first sampling trip (16th June) at sites C1-3, relative to the second trip (20th June). As would be expected, the availability of strong Cu binding ligands in the reef debris field (sites C1-3; Fig. 2) was a direct determinant of the bioavailability of Cu in this location (Fig. 6b). At low ligand concentrations, Cu was more bioavailable at the centre sites and vice versa (Fig. 6b). Bioavailable Cu-concentrations in solution were low (relative to total), ranging from 2.3 to 81.9 pM or <1% of [dCuT] (Figs 5,6a), being an order-of-magnitude lower than DGT measurements (Fig. 4). As expected from sediment measurements, the highest [Cu’] were detected at sites C1-3 adjacent to the Rena wreck, with average concentrations of 15 ± 9 pM on the 16th of June and 67.5 ± 17.7 pM on the 20th of June. It is important to note that water samples for AdCSV analyses were collected under quiescent ocean conditions, whereas DGT probes measured Cu fluxes under all conditions over the deployment period. Therefore, the DGT probes were likely to have accumulated Cu under more turbulent conditions where higher concentrations of suspended reef sediments are likely to have occurred.

Figure 5
figure5

Results of AdCSV measurements detailing total dissolved Cu concentrations ([dCuT]) and the properties of natural organic Cu-binding ligands in samples from Otaiti and Okarapu Reef (control site) collected on 16th June 2016 (orange columns) and 20th June 2016 (green columns) including ligand concentrations ([L]), conditional stability constants of ligand-Cu (CuL) complexes (logK), and the calculated bioavailable Cu concentration ([Cu’]). Error bars are ±1σ.

Figure 6
figure6

Exploration of AdCSV data: (a) Ratio of [Cu’] to [CuT] in water samples collected from Otaiti and Okarapu Reef (control) on the 16th June 2016 (orange columns) and the 20th June 2016 (green columns); and (b) relationship between Cu-binding ligand concentration and [Cu’].

Settlement plates

Recruitment onto all settlement plates was limited. Percent cover ranged from 4–25%, with coverage lowest at tiles deployed adjacent to the Cu deposit (Site C: 6.7 ± 0.9% cover) compared with the two sets of reference plates positioned between DGT sites N2 and N3 (Site A - 10.8 ± 1.4%; Site B – 12.8 ± 2.6%; Fig. 2 and Table 2). The organisms growing on plates were classified into operational taxonomic units (OTUs) based on their appearance (morphology and colour). OTUs were used due to the difficulty of identifying invertebrate recruits to species level without bringing in additional taxonomic expertise or using genetic identification methods. Settlement plate data (counts and coverage) did not meet the assumptions of parametric analyses so non-parametric Kruskal-Wallis ANOVA were used to test for differences in settlement patterns between sites.

Table 2 Operational taxonomic units (OTUs) recorded on settlement plates.

When analyses were conducted to compare total plate coverage across the three sites (A vs. B vs. C) the observed differences were not significant (p > 0.1). However, when sites A and B were grouped to compare impact (site C) vs. reference sites it became apparent that invertebrate coverage was significantly lower on Cu impacted plates (p = 0.026). A comparison of OTU richness (number of different OTUs recorded on a plate) indicated that there was no difference in diversity between sites (Site A: 3.20 ± 0.40 (OTUs per plate ± s.e.), Site B: 3.60 ± 0.53 and Site C: 3.89 ± 0.39). While OTU richness did not vary between sites, there were clear differences in the communities recruiting between impact and reference sites. Barnacles and hydroids were only recorded on plates at the most Cu affected site (site C) while foraminifera were more abundant at site C than at reference sites (p < 0.001; Table 2). In contrast, pink branching bryozoans were present on plates at sites A and B but were not recorded on plates at site C. For other OTUs there were no apparent differences in abundance between treatments (Site C vs. Sites A and B).

Discussion

Distribution of Cu contamination at Otaiti

The multi-method Cu sampling and analysis strategy deployed here provides definitive proof of a discrete zone of water borne Cu contamination on Otaiti, Astrolabe Reef  6 owing to the 7 to 12 tonnes of granulated Cu2,3,4,5,6,7,8,10 which still remain trapped beneath the wreck. While it is possible that some small proportion of Cu originated from the residual metal components of the MV Rena, we consider the Cu signal observed here primarily originated from the granulated Cu. Results of [dCuT] measurements were much higher than [dCuT] typically recorded in New Zealand coastal waters32 (generally <4 nM). The high [dCuT] also equated to elevated [Cu’] and [CuDGT], with the calculated values falling within the expected hierarchy for these techniques ([CuDGT]» [dCuT])27. Despite the very high [CuT] encountered near the location with the highest sediment Cu concentrations, [CuT] at Otaiti sites distal to the [CuT] maximum were generally equal to, or less than the [CuT] detected at the study control site of Okarapu Reef. This demonstrates that the plume of Cu in the Otaiti water column is localised around the wreck debris. Total dissolved Cu concentrations at all sites were higher than the ANZECC (2000) default trigger values for the protection of 99% of saltwater species, resulting in possible adverse effects for more sensitive species and early life stages. These ANZECC values, together with elevated [CuT], [dCuT], and [CuDGT] and settlement plate data indicate that Cu contamination continues to affect the ecological composition of the Astrolabe Reef ecosystem even after a 5-year recovery from the grounding and breakup of the Rena.

Cu speciation analysis

The data in the present study indicates the presence of only one organic ligand class with conditional stability constants of logK ≥ 11. These logK values fall within the range generally reported for L233,34. The relatively narrow range of observed stability constants (logK = 11.6 ± 0.3) may indicate a relatively uniform composition of the ligands throughout the study area. Culture experiments with a number of species of planktonic mircoorganisms as well as with blue mussel embryos have shown that these organisms can produce Cu-binding ligands under Cu-stress19,35,36,37,38,39. For example, numerous species of marine cyanobacteria (e.g. Synechococcus)19,35,36, brown algae (e.g. Fucus vesiculosus)37 and coccolithophorids (e.g. Emiliania huxleyi)38 are known to produce Cu-chelators (logK > 11) in cultures, exuded as a feedback mechanism against the potential toxicity of Cu2+ ions40,41. However, it should be noted that ligands derived from terrestrial dissolved organic matter (DOM) (i.e., humic and fulvic acids)26,42, anthropogenic inputs (i.e., stormwater/wastewater)43, and antifouling paints44 are also potential sources of Cu-complexing ligands in the marine environment40,45. Further, resuspended sediments could add to the marine organic ligand pool, although the majority of studies have indicated that only weak ligands are derived from sediments (logK < 9)46,47. AdCSV does not inform ligand composition, beyond identifying the stability of the CuL complexes and it is thus not possible to constrain ligand sources. Statements on ligand provenance remain only assumptions based on a correlation (or the lack of a correlation) of [L] with other data in the surrounding water. However, that [L] always exceeded the [CuT] strongly hints toward an active biological response by local biota to mitigate the toxic effects of the elevated Cu-levels around the Rena wreck. This inference is further supported by the fact that [Cu’] and [CuT] were higher in the vicinity of the Rena Cu deposit, during one of the sampling dates, and the [L] followed that trend. Nevertheless, more research regarding the chemical nature of prevalent ligands and the possibility of ligand production by local benthic, planktonic, and microbial communities is needed to validate this conjecture.

The concentration of organic ligands can vary temporally as well as spatially based on a multitude of biotic and abiotic processes present in complex and heterogeneous natural waters, which influence the source as well as the concentration of prevalent organic ligands (e.g. DOM species)48,49. It is well known, that mixing of fresh- and marine waters, riverine discharge levels, hydrological conditions (i.e., currents and mixed layers), as well as meteorological conditions (i.e., precipitation, storm events, photochemical ligand destruction), anthropogenic input and biological processes (e.g. ligand production, microbiological oxidation) can spatially and temporally alter the ligand pool49 and associated Cu’ concentrations. Therefore, differences and fluctuations in [Cu’] and [L], as seen in the study area during the two sampling periods, are normal, especially in dynamic marine reef environments such as Otaiti.

[L] was always in excess of [dCuT] in all samples, which reduced the [Cu’] in solution, but bioavailable [Cu’] measurements at Otaiti were often above 10−11 M (ranging from 2.3 to 81.9 pM), a threshold found to be toxic for some marine phytoplankton species50,51. Although [Cu’] recorded at Otaiti were two orders of magnitude lower than those calculated to be toxic to blue mussel embryos39, the settlement plates in the vicinity of the Rena Cu deposit showed lower benthic invertebrate recruitment. Additionally, different types of organisms were recruiting the settlement plates in high Cu’ areas. This finding illustrates that Cu’ sensitivity is species dependent with varying effects to a broad range of different marine organisms. Consequently, elevated [Cu’], both naturally and anthropogenically derived, can drive differences in organism recruitment or survival and thus alter community diversity, structure, and the functionality of affected ecosystems such as Otaiti14,52. Organisms unable to counteract persistent or intermittent high Cu’ exposures through ligand production, or other metabolic pathways, may struggle to compete with species that are more tolerant of Cu contamination. Furthermore, water samples in the present study were taken under calm conditions and thus represent a quiescent Cu baseline for the Otaiti environment. Sampling under calm conditions is likely to underestimate the [CuT] encountered during storms (due to resuspension of Cu in sediments), which would likely increase [dCuT] and [Cu’] in the water column thereby exceeding acute Cu-toxicity limits for various benthic biota, for at least short periods of time.

Future work could look at the chemical structures of organic Cu-binding ligands, the organisms and sources that produce them41 as well as the abiotic parameters influencing the ligand pool in the Otaiti aquatic environment to gain a deeper understanding of Cu-speciation and associated Cu-risks assessments in the vicinity of the Rena wreck.

Settlement plate study

Although the spatial extent of the settlement plate deployment was limited compared to the deployment of DGTs, the results indicate an effect of Cu on the recruitment of benthic invertebrates. Not only was recruitment lower on plates positioned within the area of maximum [CuT] and [Cu’] but there were differences in the types of organisms recruiting to Cu impacted plates. Some taxonomic groups (e.g. barnacles and foraminifera) were either restricted to, or more abundant, at the site of highest Cu contamination, leading to the interpretation that these organisms were more tolerant of Cu enriched water. Conversely, other OTUs (including bryozoans) were either restricted to reference sites, more abundant at reference sites, or showed no difference in abundance across the Cu contamination gradient. These results are consistent with previous studies identifying varied levels of Cu toxicity to a broad range of aquatic organisms12,53,54,55,56,57,58,59 including invertebrates, which can drive differences in benthic invertebrate recruitment and therefore community structure14,52.

Because of the limitations of the settlement plate study (limited replication and spatial distribution of sampling stations), the results should not be treated as the definitive assessment of the effects of sediment Cu contamination on the recruitment of benthic invertebrates to Otaiti. The experimental design was an economical one (in terms of time and resources), conducted in mid-winter, a time when recruitment was likely to be minimal and designed to give an indication of possible effects. Despite these caveats, the results do appear to confirm the a priori hypothesis that recruitment of invertebrates to hard substrates would be modified by waterborne Cu contamination arising from the Rena. The data indicate that both substrate coverage and community composition were affected. How these effects on recruitment will influence the ecology of sites adjacent to the zone of elevated Cu contamination is uncertain. Furthermore, this study only tested the effects of waterborne Cu contamination rather than the consequences of Cu within the recruitment substrate. In soft sediments where extremely high concentrations of Cu (up to 780 g kg−1)7 have been documented, it can probably be assumed that the ecological consequences are more severe. Water and sediment chemistry data indicate that any effects of Cu clove are localised to areas in the immediate vicinity of the Cu clove deposit. Nevertheless, the halo of [Cu’] at Otaiti could have significant localised effects in the long-term and could extend in a plume in various directions over the reef depending on conditions. While elevated [Cu] is restricted to a small proportion of the subtidal habitat available at Otaiti, the [Cu’] is present at or above the threshold for toxicity to some biota50,51 which may not be able to counteract Cu exposure through ligand production. Further experimentation and monitoring would be needed to better quantify the effects of Cu clove on recruitment and ecology, such as the potentially toxic effects of Cu on surface water phytoplankton communities. Without further research, the toxic or sub-lethal effects of Cu on reef biota and the long-term environmental consequences remain uncertain.

Conclusion

In conclusion, the water sampling and analysis reported here, demonstrate that waterborne [Cu] are elevated at Otaiti in the vicinity of the Cu clove deposit, and are well above background [Cu] recorded at a comparable reference site. Impacted sites are likely to experience episodes of very high [CuT] and [dCuT] in the water column close to sediments, depending on the degree of sediment entrainment, and are likely to have consistently elevated [Cu’] (as indicated by AdCSV and DGT measurements which integrate the average water chemistry over several days). The results of our settlement plate study support the interpretation that localised Cu contamination of the water column is likely to modify the recruitment of benthic invertebrate species at this site. Thus, elevated [CuT], [dCuT], and [Cu’] in the vicinity of the MV Rena has the potential to modify the ecological composition of the Otaiti Reef ecosystem as it recovers from the shipwreck.

Methods

Water column Cu analysis

Sample collection

Water samples were collected from discrete locations along the 25 m contour of Otaiti using a team of SCUBA divers on the 16th and 20th of June 2016. The divers positioned the DGTs at the location of the water samples. DGTs remained in-situ for 4–5 days. Water samples were taken using a pre-acid-cleaned 50 mL polyethylene tube which was connected to a peristaltic pump housed inside a shipboard clean laboratory. Water was pumped for the equivalent of three tube volumes to flush any residual sample prior to sample collection inside a Class 100 laminar flow hood. Samples were pumped directly into pre-acid cleaned60 LDPE bottles (Low-density polyethylene; Nalgene Laboratory, Penfield, NY, United States) which were rinsed three times with the fresh sample and then filled with zero headspace. Samples reserved for dCuT and Cu-speciation analysis were filtered through a 0.2 μm cartridge-filter (AcroPak, Supor)). All samples were kept refrigerated at <5 °C prior to analysis with the exception of samples for AdCSV analysis, which were filled with a 5% headspace and kept frozen prior to analysis.

Sample treatment for total Cu analysis with the HR-SF-ICP-MS

Samples for total Cu were acidified with quartz distilled HCl to a concentration of 0.024 M, resulting in a pH of ~1.8. Samples were left for 1 month prior to further processing. Subsequently, a volume of 15 mL sample was pipetted into an acid cleaned FEP vial. An internal standard (indium and lutetium) at a concentration of 5 nM as well as H2O2 were added (final concentration 26 μM) prior to UV digestion61. Hydrogen peroxide was added to support the complete oxidation of organic matter in the sample under the influence of UV-light.

A seaFAST pico system was used in off-line mode to pre-concentrate the acidified seawater samples with a factor of 10. The eluate was subsequently transferred into an acid cleaned destination vial and was then ready for High Resolution Sector Field Inductively Coupled Plasma Mass Spectrometer (HR-SF-ICP-MS) analysis. A detailed description of the method and sample preparation procedure can be found in Biller and Bruland62, Lagerström, et al.63 and Middag, et al.61.

Samples were analysed using a Nu Attom HR-SF-ICP-MS utilizing wet plasma at a resolution setting of 4000. The system was calibrated using standard additions of a multi-element stock solution to seawater of low metal concentration. Quantitative recovery on the resin was verified by comparing the slope of the calibration line obtained from the standard additions to seawater to standard additions done directly to untreated eluent acid61. Recovery of the method was acceptable (>94%). The accuracy of the method was verified by the measurement of certified reference material (SLEW-3; National Research Council, Canada) and was found to be accurate within 4.6% of the reference value for Cu (reference value: 24.39 ± 1.89 nM Cu; measured value (n = 2): 25.52 ± 0.01 nM Cu).

DGT analysis

Diffusive gradients in thin films (DGT) provide a reliable direct, in-situ measurement of the concentration of the species of interest64. To determine the concentration of labile Cu in the water column at Otaiti, Chelex-100 DGT devices were prepared in-house after Zhang and Davison64. The precision and accuracy of the devices was confirmed before deployment and were found to be accurate within 5% for Cu with respect to [CuT] in a 50 ppb standard solution (n = 5) deployment test. The assembled probes were immersed in 0.01M NaNO3 and transferred to the field in air-tight containers.

Four Chelex DGT probes were secured inside a robust plastic mesh container using cable ties. The container provided protection to the DGT probes from particles >5 mm diameter, whilst being completely permeable to seawater. Divers then transferred the container (attached to heavy weights) to the deployment location. Probes were co-located with two temperature loggers (UTBI-001, TidbiT V2 Temp Loggers) allowing the average DGT deployment temperature to be calculated at each respective depth.

After typically 4–5 days, the probes were retrieved, rinsed with deionised water (resistivity 18 MΩ) and kept in sealed, pre-cleaned individual plastic bags and were transferred to the lab at <5 °C in the dark. DGT probes were dismantled and Chelex-100 resins were eluted in 1 M ppt grade HNO3 and analysed using a Perkin Elmer (Waltham MA) quadrupole ICP-MS calibrated using certified NIST-traceable reference materials from Inorganic Ventures (Christiansburg, VA, USA) with an accuracy better than 1%65. Internal standards of known concentration were also analysed to determine instrumental drift during analysis. DGT blanks (HNO3 eluted Chelex resins) were below detection for Cu (<0.1 ppb). Reported [CuDGT] were calculated using the standard DGT theory6,29 and Cu diffusion coefficients (determined from the average temperature over the deployment).

Voltammetric methods

Total dissolved Cu-concentrations and Cu-speciation were determined by voltammetric analysis using a Metrohm 663 VA stand connected to a PGSTAT10 (Eco Chemie) potentiostat interfaced with GPES v4.9 software. The three-electrode configuration of the system included a hanging mercury drop electrode (HMDE) as the working electrode, an Ag/AgCl 3M KCl reference electrode, and a platinum counter electrode. The system was operated in the differential pulse mode at room temperature. Instrumental settings were adopted from Sander, et al.66. For detailed information on sample preparation and operating conditions of the instrument see Sander, et al.66 and Powell60.

Acidified (q-HCl) aliqouts (4 mL) of each sample (pH: 1.7 ± 0.1) were transferred into acid cleaned Teflon vials. Samples were then UV-digested for at least 12 hours in order to remove natural Cu-complexing species in solution60,67. Once UV-digested each sample was pipetted into a trace metal clean and previously conditioned voltammetric cup. From this 0.01 M salicylaldoxime (Acros Organics; SA: 98%) was added to the sample to a final concentration of 25 µM and the sample was then left to equilibrate for 20 min. Salicylaldoxime was used as the added ligand, since its complexation parameters with Cu in seawater are well characterized68. From this, all samples were buffered to pH 8.1 ± 0.2 using 50 µL of 1M borate buffer (Arcos Organics; H3BO3: 99.99%) and 15 µL trace-metal grade NH4OH (Optima™, Fisher Chemical). The total dissolved Cu concentration in each sample was then determined by adsorptive cathodic stripping voltammetry (AdCSV)67. Prior to analysis, each sample aliquot was deaerated by purging nitrogen gas over the sample for at least 2 min68,69,70. The conditioning potential was set at −0.15 V for 15–30 s with a cathodic scan from −0.15 to −0.6 V. Every measurement was repeated three times67. After the first measurement a four-point standard addition procedure of a known Cu standard (Fisher Scientific) was used to subsequently determine the [dCuT] of the sample71. The accuracy and precision of the voltammetric method was assessed by multiple measurements of a certified reference seawater sample60,67, i.e., SLEW-3. Accuracy and precision of the analytical technique was within an acceptable range of ± 3.5% SD for Cu (reference value: 24.39 ± 1.89 nM Cu; measured value (n = 2): 23.53 ± 1.45 nM Cu).

For the Cu-complexing ligand titrations, 12 aliquots (4 mL each) of each sample were separately transferred into pre-conditioned Teflon vials. Afterwards, 100 µL of 1M borate buffer was added to each sample to maintain the sample pH at 8.2 ± 0.2 during analysis. This was followed by increasing Cu-additions of an atomic absorption Cu-standard, calculated as a geometrically spaced series72, to each aliquot ranging from 0 to 550 nM66. A 20 min equilibration period was implemented to allow the Cu to bind with the natural organic ligands present in solution. Afterwards SA was added to the aliquots at a final concentration of 5 μM. Finally, all samples were left to equilibrate for a minimum of 12 hours, which was found to result in stable Cu–SA peaks66. Once equilibrated, all samples were analysed using the instrumental parameters as described for the total dissolved Cu-measurements. After completion of the titration, Cu-speciation parameters (i.e., [CuXIN], [Cu2+], [L], and logK) of each solution were obtained using the one-ligand and two-ligand complete complexation-fitting model within the ProMCC software73,74. Fitting of each titration data to a two-ligand system failed with the ProMCC software and thus samples were fitted to a one-ligand model, which resulted in reasonable at equilibrium speciation estimates of [L] and logK with derived parameters of [CuXIN] and [Cu2+]. Finally, the bioavailable [Cu’] was calculated as the sum of [CuXIN] and [Cu2+].

Settlement plates

The deployment of settlement plates was opportunistic and as such it was not possible to replicate the spatial arrangement of the DGT deployment. Instead, settlement plates were placed at the site of the Cu deposit (Site C) and at two sites (Sites A and B) between N2 and N3 (Fig. 2). Each settlement plate deployment unit consisted of three settlement plates (15 × 15 cm terracotta tiles) cable tied to a 1 m length of PVC pipe (Fig. 7). One end of the pipe was secured to a plastic coated 15 kg weight plate. The other end of the pipe was secured to a polystyrene net float. Three of these units (a total of nine settlement plates) were deployed at each site by SCUBA divers. After a period of 3 months, the plates were retrieved and photographed. Photographs were loaded into ImageJ (ImageJ, Ver. 1.49) and total plate coverage determined by summing the surface area of all parts of a plate covered by encrusting organisms. The OTUs used for comparing community composition between deployment sites were defined during this initial examination. OTUs definition was based on morphology (viewed under dissecting scope) and colour (Table 2). Once OTUs were defined, coverage (hydroids) of counts either individuals (barnacles and anemones) or colonies (bryozoans and ascidians) were determined for the entire plate. Kruskal-Wallis ANOVAs were performed in Statistica (Ver. 13) to test for differences in plate coverage between all sites (A vs. B vs. C) and between reference and impact sites (sites A and B vs. C). Subsequently, differences in counts and coverage of OTUs between reference and impact sites were assessed, again using Kruskal-Wallis ANOVAs.

Figure 7
figure7

Panel A shows a schematic of settlement plate deployment unit including (a) polystyrene net float, (b) PVC pipe, (c) settlement plates and (d) 15 kg plastic coated weight. Three of these units were deployed at each settlement plate sampling station (Sites A, B and C). Panel B shows an example of a 15 × 15 cm terracotta settlement plate deployed at Otaiti to a depth of 25 m for 3 months.

References

  1. 1.

    Dobie, G. Global claims review. (Allianz Global Corporate & Specialty, 2014).

  2. 2.

    Dimitrakakis, E., Hahladakis, J. & Gidarakos, E. The “Sea Diamond” shipwreck: Environmental impact assessment in the water column and sediments of the wreck area. International Journal of Environmental Science and Technology 11, 1421–1432, https://doi.org/10.1007/s13762-013-0331-z (2014).

  3. 3.

    Leichenko, R. & O’Brien, K. Environmental Change and Globalization: Double Exposures (2008).

  4. 4.

    Battershill, C. N., Ross, P. R. & Schiel, D. R. The MV Rena shipwreck: time-critical scientific response and environmental legacies. New Zealand Journal of Marine and Freshwater Research 50, 173–182, https://doi.org/10.1080/00288330.2015.1134593 (2016).

  5. 5.

    Chapman, P. In The Telegraph (2012).

  6. 6.

    Dempsey, T., Ross, P. M., Hartland, A., McSweeney, C. & Battershill, C. N. Measurement of shipwreck-derived waterborne trace metals using DGT samplers. New Zealand Journal of Marine and Freshwater Research 50, 115–130, https://doi.org/10.1080/00288330.2015.1127829 (2016).

  7. 7.

    Ross, P. M., Battershill, C. N. & Loomb, C. The wreck of the MV Rena: spatio-temporal analysis of ship-derived contaminants in the sediments and fauna of Astrolabe Reef. New Zealand Journal of Marine and Freshwater Research 50, 87–114, https://doi.org/10.1080/00288330.2015.1077873 (2016).

  8. 8.

    Schiel, D. R., Ross, P. M. & Battershill, C. N. Environmental effects of the MV Rena shipwreck: cross-disciplinary investigations of oil and debris impacts on a coastal ecosystem. New Zealand Journal of Marine and Freshwater Research 50, 1–9, https://doi.org/10.1080/00288330.2015.1133665 (2016).

  9. 9.

    Beamsley, B. J. In New Zealand Environment Court (2016).

  10. 10.

    Faaui, T. N., Morgan, T. K. K. B. & Hikuroa, D. C. H. Ensuring objectivity by applying the Mauri Model to assess the post-disaster affected environments of the 2011 MV Rena disaster in the Bay of Plenty, New Zealand. Ecological Indicators 79, 228–246, https://doi.org/10.1016/j.ecolind.2017.03.055 (2017).

  11. 11.

    Dong, Y., Rosenbaum, R. K. & Hauschild, M. Z. Assessment of Metal Toxicity in Marine Ecosystems: Comparative Toxicity Potentials for Nine Cationic Metals in Coastal Seawater. Environmental Science and Technology 50, 269–278, https://doi.org/10.1021/acs.est.5b01625 (2016).

  12. 12.

    Dang, F., Zhong, H. & Wang, W. X. Copper uptake kinetics and regulation in a marine fish after waterborne copper acclimation. Aquatic Toxicology 94, 238–244, https://doi.org/10.1016/j.aquatox.2009.07.011 (2009).

  13. 13.

    Simpson, S. L. & Spadaro, D. A. Performance and sensitivity of rapid sublethal sediment toxicity tests with the amphipod Melita plumulosa and copepod Nitocra spinipes. Environmental Toxicology and Chemistry 30, 2326–2334, https://doi.org/10.1002/etc.633 (2011).

  14. 14.

    Hill, N. A., Simpson, S. L. & Johnston, E. L. Beyond the bed: Effects of metal contamination on recruitment to bedded sediments and overlying substrata. Environmental Pollution 173, 182–191, https://doi.org/10.1016/j.envpol.2012.09.029 (2013).

  15. 15.

    Johnston, E. L. & Keough, M. J. Competition modifies the response of organisms to toxic disturbance. Marine Ecology Progress Series 251, 15–26 (2003).

  16. 16.

    Tercier-Waeber, M.-L., Stoll, S. & Slaveykova, V. I. Trace metal behavior in surface waters: Emphasis on dynamic spéciation, sorption processes and bioavailability. Vol. 65 (2012).

  17. 17.

    Morel, F. M. M. Principles of aquatic chemistry. Vol. 30 (John Wiley & Sons, Inc., Somerset, N.J., 1983).

  18. 18.

    Deruytter, D. et al. The Combined Effect of Dissolved Organic Carbon and Salinity on the Bioaccumulation of Copper in Marine Mussel Larvae. Vol. 48 (2013).

  19. 19.

    Brand, L. E., Sunda, W. G. & Guillard, R. R. L. Reduction of marine phytoplankton reproduction rates by copper and cadmium. Journal of Experimental Marine Biology and Ecology 96, 225–250, https://doi.org/10.1016/0022-0981(86)90205-4 (1986).

  20. 20.

    Kozelka, P. B. & Bruland, K. W. Chemical speciation of dissolved Cu, Zn, Cd, Pb in Narragansett Bay, Rhode Island. Marine Chemistry 60, 267–282, https://doi.org/10.1016/S0304-4203(97)00107-2 (1998).

  21. 21.

    Lorenzo, J. I., Nieto, O. & Beiras, R. Effect of humic acids on speciation and toxicity of copper to Paracentrotus lividus larvae in seawater. Vol. 58 (2002).

  22. 22.

    Semeniuk, D. M., Bundy, R. M., Payne, C. D., Barbeau, K. A. & Maldonado, M. T. Acquisition of organically complexed copper by marine phytoplankton and bacteria in the northeast subarctic Pacific Ocean. Marine Chemistry 173, 222–233, https://doi.org/10.1016/j.marchem.2015.01.005 (2015).

  23. 23.

    Amon, R. M. W. & Benner, R. Photochemical and microbial consumption of dissolved organic carbon and dissolved oxygen in the Amazon River system. Geochimica et Cosmochimica Acta 60, 1783–1792, https://doi.org/10.1016/0016-7037(96)00055-5 (1996).

  24. 24.

    Lawes, J. C., Clark, G. F. & Johnston, E. L. Contaminant cocktails: Interactive effects of fertiliser and copper paint on marine invertebrate recruitment and mortality. Marine Pollution Bulletin 102, 148–159, https://doi.org/10.1016/j.marpolbul.2015.11.040 (2016).

  25. 25.

    Lawes, J. C., Dafforn, K. A., Clark, G. F., Brown, M. V. & Johnston, E. L. Multiple stressors in sediments impact adjacent hard substrate habitats and across biological domains. Science of the Total Environment 592, 295–305, https://doi.org/10.1016/j.scitotenv.2017.03.083 (2017).

  26. 26.

    Sander, S. G., Buck, K. N. & Wells, M. The effect of natural organic ligands on trace metal speciation in San Francisco Bay: Implications for water quality criteria. Marine Chemistry 173, 269–281, https://doi.org/10.1016/j.marchem.2014.09.015 (2015).

  27. 27.

    Sigg, L. et al. Comparison of analytical techniques for dynamic trace metal speciation in natural freshwaters. Environmental Science and Technology 40, 1934–1941, https://doi.org/10.1021/es051245k (2006).

  28. 28.

    Zhang, H. & Davison, W. Diffusional characteristics of hydrogels used in DGT and DET techniques. Analytica Chimica Acta 398, 329–340 (1999).

  29. 29.

    Davison, W. & Zhang, H. Progress in understanding the use of diffusive gradients in thin films (DGT) – back to basics. Environmental Chemistry 9, 1–13, https://doi.org/10.1071/EN11084 (2012).

  30. 30.

    Menegário, A. A., Yabuki, L. N. M., Luko, K. S., Williams, P. N. & Blackburn, D. M. Use of diffusive gradient in thin films for in situ measurements: A review on the progress in chemical fractionation, speciation and bioavailability of metals in waters. Analytica Chimica Acta 983, 54–66, https://doi.org/10.1016/j.aca.2017.06.041 (2017).

  31. 31.

    Dabrin, A. et al. Metal measurement in aquatic environments by passive sampling methods: Lessons learning from an in situ intercomparison exercise. Environmental Pollution 208, 299–308, https://doi.org/10.1016/j.envpol.2015.08.049 (2016).

  32. 32.

    Croot, P. L. & Hunter, K. A. Trace metal distributions across the continental shelf near Otago Peninsula, New Zealand. Marine Chemistry 62, 185–201, https://doi.org/10.1016/S0304-4203(98)00036-X (1998).

  33. 33.

    Coale, K. H. & Bruland, K. W. Copper complexation in the Northeast Pacific. Limnology and Oceanography 33, 1084–1101, https://doi.org/10.4319/lo.1988.33.5.1084 (1988).

  34. 34.

    Tang, D., Warnken, K. W. & Santschi, P. H. Organic complexation of copper in surface waters of Galveston Bay. Limnology and Oceanography 46, 321–330, https://doi.org/10.4319/lo.2001.46.2.0321 (2001).

  35. 35.

    Moffett, J. W. & Brand, L. E. Production of strong, extracellular Cu chelators by marine cyanobacteria in response to Cu stress. Limnology and Oceanography 41, 388–395, https://doi.org/10.4319/lo.1996.41.3.0388 (1996).

  36. 36.

    Moffett, J. W., Zika, R. G. & Brand, L. E. Distribution and potential sources and sinks of copper chelators in the Sargasso Sea. Deep Sea Research Part A. Oceanographic Research Papers 37, 27–36, https://doi.org/10.1016/0198-0149(90)90027-S (1990).

  37. 37.

    Gledhill, M., Nimmo, M., Hill, S. J. & Brown, M. T. The Release of Copper-Complexing Ligands by the Brown Alga Fucus Vesiculosus (Phaeophyceae) in Response to Increasing Total Copper Levels. Journal of Phycology 35, 501–509, https://doi.org/10.1046/j.1529-8817.1999.3530501.x (1999).

  38. 38.

    Leal, M. F. C., Vasconcelos, M. T. S. D. & van den Berg, C. M. G. Copper-induced release of complexing ligands similar to thiols by Emiliania huxleyi in seawater cultures. Limnology and Oceanography 44, 1750–1762, https://doi.org/10.4319/lo.1999.44.7.1750 (1999).

  39. 39.

    Zitoun, R. et al. Copper toxicity to blue mussel embryos (Mytilus galloprovincialis). Vol. 653 (2018).

  40. 40.

    Shank, G. C., Skrabal, S. A., Whitehead, R. F. & Kieber, R. J. Strong copper complexation in an organic-rich estuary: the importance of allochthonous dissolved organic matter. Marine Chemistry 88, 21–39, https://doi.org/10.1016/j.marchem.2004.03.001 (2004).

  41. 41.

    Vraspir, J. M. & Butler, A. Chemistry of Marine Ligands and Siderophores. Annual Review of Marine Science 1, 43–63, https://doi.org/10.1146/annurev.marine.010908.163712 (2009).

  42. 42.

    Hartland, A., Lead, J. R., Slaveykova, V. I., O’ Carroll, D. & Valsami-Jones, E. The environmental significance of natural nanoparticles. Nature Educ. Knowl. 4, 7 (2013).

  43. 43.

    DePalma, S. G. S., Ray Arnold, W., McGeer, J. C., George Dixon, D. & Scott Smith, D. Effects of dissolved organic matter and reduced sulphur on copper bioavailability in coastal marine environments. Ecotoxicology and Environmental Safety 74, 230–237, https://doi.org/10.1016/j.ecoenv.2010.12.003 (2011).

  44. 44.

    Swope, B. L., Barbeau, K., Bundy, R., McDonald, J. A. & Rivera-Duarte, I. Life cycle contributions of copper from vessel painting and maintenance activities AU - Earley, Patrick J. Biofouling 30, 51–68, https://doi.org/10.1080/08927014.2013.841891 (2014).

  45. 45.

    Arnold, W. R., Cotsifas, J. S., Smith, D. S., Le Page, S. & Gruenthal, K. M. A comparison of the copper sensitivity of two economically important saltwater mussel species and a review of previously reported copper toxicity data for mussels: Important implications for determining future ambient copper saltwater criteria in the USA. Environmental Toxicology 24, 618–628, https://doi.org/10.1002/tox.20452 (2009).

  46. 46.

    Skrabal, S. A., Donat, J. R. & Burdige, D. J. Fluxes of copper-complexing ligands from estuarine sediments. Limnology and Oceanography 42, 992–996, https://doi.org/10.4319/lo.1997.42.5.0992 (1997).

  47. 47.

    Jacquot, J. E. & Moffett, J. W. Copper distribution and speciation across the International GEOTRACES Section GA03. Deep-Sea Research Part Ii-Topical Studies in Oceanography 116, 187–207, https://doi.org/10.1016/j.dsr2.2014.11.013 (2015).

  48. 48.

    Town, R. M. & Filella, M. A comprehensive systematic compilation of complexation parameters reported for trace metals in natural waters. Aquatic Sciences 62, 252–295, https://doi.org/10.1007/pl00001335 (2000).

  49. 49.

    Osterholz, H., Kirchman, D. L., Niggemann, J. & Dittmar, T. Environmental Drivers of Dissolved Organic Matter Molecular Composition in the Delaware Estuary. Frontiers in Earth Science 4, https://doi.org/10.3389/feart.2016.00095 (2016).

  50. 50.

    Sunda, W. G., Tester, P. A. & Huntsman, S. A. Effects of cupric and zinc ion activities on the survival and reproduction of marine copepods. Marine Biology 94, 203–210, https://doi.org/10.1007/bf00392932 (1987).

  51. 51.

    Sunda, W. G., Tester, P. A. & Huntsman, S. A. Toxicity of trace metals to Acartia tonsa in the Elizabeth River and southern Chesapeake Bay. Estuarine, Coastal and Shelf Science 30, 207–221, https://doi.org/10.1016/0272-7714(90)90048-V (1990).

  52. 52.

    Burton, G. A. & Johnston, E. L. Assessing contaminated sediments in the context of multiple stressors. Environmental Toxicology and Chemistry 29, 2625–2643, https://doi.org/10.1002/etc.332 (2010).

  53. 53.

    Bosse, C. et al. Copper bioavailability and toxicity to Mytilus galloprovincialis in Shelter Island Yacht Basin, San Diego, CA. Marine Pollution Bulletin 85, 225–234, https://doi.org/10.1016/j.marpolbul.2014.05.045 (2014).

  54. 54.

    Campbell, A. L., Mangan, S., Ellis, R. P. & Lewis, C. Ocean acidification increases copper toxicity to the early life history stages of the polychaete arenicola marina in artificial seawater. Environmental Science and Technology 48, 9745–9753, https://doi.org/10.1021/es502739m (2014).

  55. 55.

    Deruytter, D. et al. Salinity and dissolved organic carbon both affect copper toxicity in mussel larvae: Copper speciation or competition cannot explain everything. Environmental Toxicology and Chemistry 34, 1330–1336, https://doi.org/10.1002/etc.2924 (2015).

  56. 56.

    Lewis, C. et al. Ocean acidification increases copper toxicity differentially in two key marine invertebrates with distinct acid-base responses. Scientific Reports 6, https://doi.org/10.1038/srep21554 (2016).

  57. 57.

    Patel, P. P. & Bielmyer-Fraser, G. K. The influence of salinity and copper exposure on copper accumulation and physiological impairment in the sea anemone, Exaiptasia pallida. Comparative Biochemistry and Physiology Part - C: Toxicology and Pharmacology 168, 39–47, https://doi.org/10.1016/j.cbpc.2014.11.004 (2015).

  58. 58.

    Roberts, D. A., Poore, A. G. B. & Johnston, E. L. Ecological consequences of copper contamination in macroalgae: Effects on epifauna and associated herbivores. Environmental Toxicology and Chemistry 25, 2470–2479, https://doi.org/10.1897/05-661R.1 (2006).

  59. 59.

    Tait, T. N., Cooper, C. A., McGeer, J. C., Wood, C. M. & Smith, D. S. Influence of dissolved organic matter (DOM) source on copper speciation and toxicity to Brachionus plicatilis. Environmental Chemistry 13, 496–506, https://doi.org/10.1071/EN15123 (2016).

  60. 60.

    Powell, Z. Voltammetric Studies on the Stabilisation of Dissolved Copper in Hydrothermal Vent Fluids PhD thesis, University of Otago (2015).

  61. 61.

    Middag, R. et al. Intercomparison of dissolved trace elements at the Bermuda Atlantic Time Series station. Marine Chemistry 177, 476–489, https://doi.org/10.1016/j.marchem.2015.06.014 (2015).

  62. 62.

    Biller, D. V. & Bruland, K. W. Analysis of Mn, Fe, Co, Ni, Cu, Zn, Cd, and Pb in seawater using the Nobias-chelate PA1 resin and magnetic sector inductively coupled plasma mass spectrometry (ICP-MS). Marine Chemistry 130-131, 12–20, https://doi.org/10.1016/j.marchem.2011.12.001 (2012).

  63. 63.

    Lagerström, M. E. et al. Automated on-line flow-injection ICP-MS determination of trace metals (Mn, Fe, Co, Ni, Cu and Zn) in open ocean seawater: Application to the GEOTRACES program. Marine Chemistry 155, 71–80, https://doi.org/10.1016/j.marchem.2013.06.001 (2013).

  64. 64.

    Zhang, H. & Davison, W. Performance characteristics of diffusion gradients in thin films for the in situ measurement of trace metals in aqueous solution. Analytical Chemistry 67, 3391–3400 (1995).

  65. 65.

    Hartland, A., Andersen, M. S. & Hamilton, D. P. Phosphorus and arsenic distributions in a seasonally stratified, iron- and manganese-rich lake: microbiological and geochemical controls. Environmental Chemistry 12, 708–722, https://doi.org/10.1071/EN14094 (2015).

  66. 66.

    Sander, S. G., Koschinsky, A., Massoth, G., Stott, M. & Hunter, K. A. Organic complexation of copper in deep-sea hydrothermal vent systems. Environmental Chemistry 4, 81–89, https://doi.org/10.1071/EN06086 (2007).

  67. 67.

    Kleint, C. et al. Organic Cu-complexation at the shallow marine hydrothermal vent fields off the coast of Milos (Greece), Dominica (Lesser Antilles) and the Bay of Plenty (New Zealand). Marine Chemistry 173, 244–252, https://doi.org/10.1016/j.marchem.2014.10.012 (2015).

  68. 68.

    Lucia, M., Campos, A. M. & van den Berg, C. M. G. Determination of copper complexation in sea water by cathodic stripping voltammetry and ligand competition with salicylaldoxime. Analytica Chimica Acta 284, 481–496, https://doi.org/10.1016/0003-2670(94)85055-0 (1994).

  69. 69.

    Protti, P. Introduction to Modern Voltammetric and Polarographic Analysis Techniques. IV Edition edn, 37 (AMEL Electrochemistry, 2001).

  70. 70.

    Louis, Y. et al. Characterisation and modelling of marine dissolved organic matter interactions with major and trace cations. Marine Environmental Research 67, 100–107, https://doi.org/10.1016/j.marenvres.2008.12.002 (2009).

  71. 71.

    Henze, G. In Metal Speciation in the Environment (eds Broekaert, J. A. C., Güçer, Ş.& Adams, F.) 391–408 (Springer Berlin Heidelberg, 1990).

  72. 72.

    Garnier, C., Pižeta, I., Mounier, S., Benaı̈m, J. Y. & Branica, M. Influence of the type of titration and of data treatment methods on metal complexing parameters determination of single and multi-ligand systems measured by stripping voltammetry. Analytica Chimica Acta 505, 263-–275, https://doi.org/10.1016/j.aca.2003.10.066 (2004).

  73. 73.

    Omanović, D. et al. Significance of data treatment and experimental setup on the determination of copper complexing parameters by anodic stripping voltammetry. Analytica Chimica Acta 664, 136–143, https://doi.org/10.1016/j.aca.2010.02.008 (2010).

  74. 74.

    Omanović, D. G. C. & Pižetaa, I. ProMCC software, https://sites.google.com/site/mccprosece/download (2015).

  75. 75.

    ANZECC. (ed. Ministry for the Environment) (2000).

Download references

Acknowledgements

This work was made possible in large part by the financial support of Konstantinos Zacharatos and P & I Services, the owner and insurer of the MV Rena. The IAEA is grateful to the Government of the Principality of Monaco for the support provided to its Environment Laboratories. R.Z. received a scholarship from the University of Otago. A.H. completed the manuscript with the support of a Rutherford Discovery Fellowship (RDF-UOW1601). P.M.R. completed the manuscript with the support of a Royal Society of New Zealand Marsden FastStart grant (contract number UOW 1503). We are grateful to Rex Fairweather and David Culliford for technical and scientific diving assistance during fieldwork, and Steve Cameron for ICP-MS analysis of DGT eluents.

Author information

This study is the result of a team effort. Sample materials (acid washed bottles, portable laminar flow cabinet, pump and other equipment) were prepared by University of Otago (UoO) staff R.M., S.S. and R.Z. and shipped to the University of Waikato (UoW). UoW staff P.R., A.H. and A.L. planned and completed the field sampling campaign with guidance from S.D.L. Shipboard sample processing for aquatic chemistry was completed by A.H. while P.R. and A.L. completed associated scientific diving activities involving water sampling, DGT and settlement plate deployments and ran overall logistics. P.R. and A.L. completed the taxonomic analysis of the settlement plates. H.S. manufactured the DGT probes and prepared them for ICP-MS analysis post-deployment. R.M. completed HR-SF-ICP-MS analysis of the water samples and R.Z. completed the AdCSV measurements under the supervision of S.S. The manuscript was written by A.H. with equal contributions from R.Z. and P.R. and with further contributions from all the authors.

Correspondence to Philip M. Ross.

Ethics declarations

Competing Interests

The authors declare no competing interests.

Additional information

Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Hartland, A., Zitoun, R., Middag, R. et al. Aqueous copper bioavailability linked to shipwreck-contaminated reef sediments. Sci Rep 9, 9573 (2019). https://doi.org/10.1038/s41598-019-45911-8

Download citation

Comments

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.