Abstract
This paper presents a platform combining an inverse electromagnetic design computational method with additive manufacturing to design and fabricate all-dielectric metadevices. As opposed to conventional flat metasurface-based devices that are composed of resonant building blocks resulting in narrow band operation, the proposed design approach creates non-resonant, broadband (Δλ/λ up to >50%) metadevices based on low-index dielectric materials. High-efficiency (transmission >60%), thin (≤2λ) metadevices capable of polarization splitting, beam bending, and focusing are proposed. Experimental demonstrations are performed at millimeter-wave frequencies using 3D-printed devices. The proposed platform can be readily applied to the design and fabrication of electromagnetic and photonic metadevices spanning microwave to optical frequencies.
Similar content being viewed by others
Introduction
Conventional optical elements that control the polarization, phase and amplitude of electromagnetic (EM) radiation such as lenses, polarizers, beamsplitters, and mirrors are typically engineered at a scale much larger than the wavelength. Within the last two decades, significant amount of research has been devoted to understand light-matter interactions and design novel materials and electromagnetic devices with subwavelength features. Metamaterials, and more generally materials composed of nanostructures with subwavelength feature size, have emerged as a viable platform to manipulate electromagnetic radiation in unconventional manners1,2. In particular, photonic crystals3 and negative-index materials4 have been used to achieve sub-diffraction lensing5,6,7. More recently, metasurfaces8,9,10 have gained substantial interest due to their ability to perform optical functionalities such as lensing11, holograms12,13 and beam shaping14 within an extremely thin layer. Although the ability to control phase, amplitude and polarization using subwavelength-thick metasurfaces is a promising route towards building miniature optical devices, they suffer from several drawbacks prohibiting their potential in replacing conventional bulk optical elements. Initial metasurface designs utilized plasmonic metals that exhibit high optical losses and thus were of relatively low efficiency15. Lossy metals have been replaced with high-index dielectric materials like amorphous silicon16, but such metasurfaces often rely on Mie-type resonances that result in a narrow wavelength range of operation14,17.
Typical metasurface design starts with identification of an optical resonator with a well-defined geometrical shape, such as triangles18, rectangles12,19, ellipses14 or V-antennas8,15. Phase information is then calculated for various geometrical parameters such as radius, width, orientation, etc.16. The number of degrees of freedom in the design of these shapes is very limited, which makes it difficult to optimize both efficiency and bandwidth of metadevices while achieving full control of the polarization. Here, we use an inverse electromagnetic method20,21,22,23,24,25,26 to design high-efficiency (>60%), broadband (Δλ/λ > 25%), dielectric-based thin (≤2λ) electromagnetic metadevices overcoming the aforementioned limitations. Inverse design opens up the entire design space to enable metadevices with increased and enhanced functionalities. In order to demonstrate the feasibility of our inverse design approach, we use additive manufacturing to print a low-loss polymer into a complex geometrical pattern. We demonstrate the design, fabrication and characterization of wavelength-scale metadevices for bending, polarization splitting and focusing of EM radiation at millimeter-wave frequencies.
Design method
First, we design two meta-gratings to behave as polarization beamsplitters for normally incident free-space radiation. As illustrated in Fig. 1A, those devices bend parallel and perpendicular polarizations to opposite diffraction orders. We also design a meta-grating that bends both polarizations to the same diffraction order (Fig. 1B). Finally, we propose a ~λ-thick flat metalens (Fig. 1C) that converts a normally incident plane-wave into a focusing cylindrical wave.
We use the objective-first algorithm22,27,28 in which the electromagnetic wave equation:
is treated as an optimization problem. This nonlinear optimization is decomposed in two subproblems, where each variable (ε and E) is fixed while linear optimization is performed on the other variable, alternatively and iteratively, and where boundary electromagnetic field distributions reprenting the desired behavior are constraints of the model. There is no general method to find the optimum solution of (1), but the proposed method converges most of the times towards solutions that satisfy desired functionality with acceptable performance. An on-chip wavelength splitter22 and an optical diode29 have been successfully demonstrated using such inverse electromagnetic design approach.
Bending and polarization splitting are achieved using meta-gratings that convert an input plane wave to an output plane wave with a different diffraction order than m = 0, with periodic boundary conditions along the x-axis. For metalenses, we aim to focus an input plane wave at a desired focal distance; hence, the output is chosen to be the field of a cylindrical wave centered in the desired focal point, following the equation (approximation at large r):
where r is the distance from the focal point. Metalenses do not perform like a grating; therefore, we set the boundary conditions of a perfectly matched layer (PML) along the x direction. The designs are two-dimensional, which corresponds to metadevices with infinite height along z. In practice, the fabricated devices are ≈10λ thick.
Experimental Section
Design and fabrication
Inverse-designed metadevices are fabricated using additive manufacturing, commonly called 3D-printing. This bottom-up approach allows the fabrication of very complex devices with a large aspect ratio. Furthermore, 3D-printing is an incredibly scalable method, with resolutions ranging from 100 nm to 1 mm30,31,32, allowing the fabrication of electromagnetic devices for applications from the visible to the millimeter- wave and microwave regimes33,34,35,36. Here, we demonstrate the proposed devices in the millimeter-wave regime (f > 30 GHz) using high impact polystyrene (HIPS) and a consumer grade 3D-printer based on fused deposition modeling for the fabrication. The material is chosen for its low cost and very low attenuation in the microwave to millimeter-wave region, with a loss-tangent measured to be \(\tan \,\delta < 0.003\) over the 26–38 GHz band. In this band, the real part of the dielectric constant of HIPS \(\varepsilon ^{\prime} \approx 2.3(n\approx 1.52)\), which is then used as a constraint in our algorithm to design binary devices made of air (ε = 1) and HIPS (ε = 2.3). Because of the low index, the phase difference between the input and output is approximately proportional to the effective thickness of the polymer. Therefore, in order to allow a 2π phase shift between a part full of polymer and a part full of air, the device thickness needs to obey:
which means that the minimum device thickness is around 2λ.
Measurement setup
To test the electromagnetic properties of the devices, a vector network analyzer (VNA) generates the input signal that is transmitted through a high-gain horn antenna placed far away from the sample (distance > 100λ) in order to produce a plane wave perpendicularly incident on the input surface. The device is surrounded by radar absorbing material to prevent reflections from the surroundings. For the three meta-gratings, the transmitted power is measured in the far-field (>100λ) with a low-gain horn antenna as a function of the angle between −40° and 40° in 2° steps and as a function of the frequency between 26 GHz (11.5 mm) and 38 GHz (7.9 mm). For the lenses, the output power is mapped along the axial plane on the right side of the device using a probe antenna attached to a X-Y stage. The measurement starts around 1 cm to the right of the device due to technical limitations of the setup, which is the reason why the experimental intensity maps are truncated when compared to the simulated maps.
Results
Meta-gratings
First, we demonstrate a free-space polarization splitter. The proposed metadevice (Fig. 2A) deflects a normal incident plane-wave polarized along y (parallel) and z (perpendicular) directions into m = +1 and m = −1 diffraction orders respectively with high efficiency and over a broad bandwidth. The width is chosen to be ~2λ to reach desired phase change as explained in the experimental section. The periodicity, L along y is determined by the deflection angle θ of the desired diffraction order m (here m = ±1 for all devices), following the grating equation \(L\,\sin \,\theta =m{\lambda }\). We designed and optimized the metadevice for an operation frequency of 33 GHz (free space wavelength of λ = 9.1 mm) and a deflection angle of θ = ±30°, for which L = 1.8 cm. The inverse-design algorithm generates a binary refractive-index distribution of dielectric and air that is then printed with dimensions of 2 cm × 7.2 cm × 8 cm. A photograph of the 3D-printed metadevice is shown next to the computer-generated pattern in Fig. 2A, which shows the high fidelity of the 3D-printing method.
We measured the far-field angular transmission through the fabricated metadevice to verify the predicted polarization splitting behavior. Figure 2B plots the simulated and measured power distributions at 33 GHz. We observe that a plane wave with parallel polarization is bent at an angle θ = +30°, whereas the perpendicular polarization is deflected with an angle of θ = −30°. The total power transmitted by the metadevice at 33 GHz is measured to be 76% for the parallel polarization and 54% for the perpendicular polarization, which are lower than the simulated values of 90%. The discrepancy is likely due to structure imperfections in the fabricated devices, the finite number of periods in the printed structures as well as an imperfect plane-wave input. The rejection ratio, defined as the ratio between the peak intensity and the maximum intensity outside the main peak, is experimentally found to be 5.2 dB and 7.0 dB for the parallel and perpendicular polarizations, respectively, which are close to the simulated values of 6.6 dB and 9.3 dB, respectively.
We perform full-field electromagnetic simulations to calculate the electromagnetic properties of the metadevice. We plot the vertical fields, i.e. H z for parallel polarization (Fig. 2C) and E z for perpendicular polarization (Fig. 2D), at 33 GHz. The spatial field distribution provides a clear picture of how the EM waves propagate inside the metadevice. In metasurfaces based on resonant geometric elements, the phase change is due to the interaction of the incoming plane-wave to a strong Mie resonance mode14, which typically results in a relatively narrowband operation. Here, the phase change does not stem from the interaction with a specific resonant mode, but rather due to light propagation inside the dielectric structure, with a larger phase shift of 6π in a part filled with dielectric (ε = 2.3) than a 4π shift in a part mostly void (ε = 1.0). The polarization splitting is a result of the different phase-change response of the device to different polarizations owing to its complex dielectric shape.
Although we choose 33 GHz to be the frequency to optimize for highest efficiency in our inverse-design algorithm, we observe broad operation bandwidth that spans a range of frequencies from 27 to 38 GHz, for a relative bandwidth Δλ/λ ≈ 33%, which is enabled by the inverse-design method favoring non-resonant dielectric structures. Figure 2 plots simulated (E,F) and measured (G,H) power transmitted in the far-field as a function of the angle and the frequency for parallel (E,G) and perpendicular (F,H) polarizations. The simulations and measurements agree relatively well.
In order to demonstrate the versatility and flexibility of the inverse-design approach, we designed and fabricated two additional metadevices that bend the millimeter-waves. The first one is a polarization splitter with a bending angle of +/−15° (Fig. 3A). Similar to the 30° splitter, this device presents a gradient of dielectric filling fraction along the y-direction with a larger periodicity (L = 3.5 cm) in order to favor a smaller bending angle. The simulated and measured angular far-field transmitted powers are plotted for both polarizations at 33 GHz in Fig. 3B. The measured rejection ratios for the 15° splitter are 8.2 dB and 10.6 dB for parallel and perpendicular polarizations respectively. The device has a dielectric filling fraction with a similar profile to that of a bending device towards the +15° diffraction order. The polarization splitting is due to the coupling of perpendicular polarization to a resonant wave propagating along the y-direction inside the device, which reverses the bending direction. This explains the lower bandwidth of the device for perpendicular polarization, from 31 to 37 GHz (a relative bandwidth of 18%), compared to a very large bandwidth for the bending behavior of parallel polarization, from 22 to 44 GHz (data not shown). The designs, simulated fields and broadband far-field data are shown in Figure S1 in the supplementary information.
In addition to polarization beam-splitter, we also designed and realized a polarization-independent bending device (Fig. 3C) which bends both polarizations to the same diffraction order. Simulations and experimental results of the far-field power at 33 GHz are shown in Fig. 3D, showing very good agreement between the theory and experiment. The designs, simulated fields and broadband far-field data are shown in Figure S2. Although polarization-independent bending of EM radiation can be achieved with a triangular blazed grating (Fig. 4D), such gratings deflect significant amount of power to higher diffraction orders, as shown in Fig. 4E,F. On average from 26 to 38 GHz, the inverse-designed device reduces the amount of power sent into undesired diffraction orders by a factor of 2.8 for parallel polarization and 2.0 for perpendicular polarization when compared to a blazed grating of similar thickness, which can be seen on the far-field power in Fig. 4B,C. The bending to the first diffraction order extends to 44 GHz with high efficiency (data not shown), which corresponds to a relative bandwidth of 55%, but significant power is diffracted to higher orders for larger frequencies.
Metalenses
Next, we propose and design flat metalenses using the inverse-design algorithm and boundary conditions as illustrated in Fig. 1B. We designed and fabricated two different metalenses with focal lengths of 2λ and 15λ, respectively. Both lenses are optimized and scaled for operation around 38 GHz (λ = 7.9 mm). The first metalens is 1.5-cm wide, 10-cm long, the second is 2.5-cm wide and 15-cm long and both are 10-cm tall. A picture of each device is shown with the computer-generated design in Fig. 5.
The electromagnetic behavior of both devices is simulated with a perpendicularly-polarized incoming plane wave. The electric-field intensity profiles for the short-range and long-range metalenses are plotted in Fig. 5A,B, respectively. We also performed a 2D scan of the transmitted power behind the metalenses using a millimeter-wave probe antenna positioned at z = 5 cm. The measured spatial intensity distribution in the x-y plane for the short-range and long-range lenses are provided in Fig. 5C,D, respectively. The simulated and measured spatial-intensity distributions closely match. As expected, the first device focuses EM radiation 1.5 cm (~2λ) away from the device whereas the second device’s focal point is located 12 cm (~15λ) away. The full-width-at-half-maximum (FWHM) of the focused radiation for both devices are 0.5 cm and 1.1 cm as shown in Fig. 5E,F, respectively, corresponding to practical numerical apertures (NAs) of 0.8 and 0.36 respectively, close to the theoretical values of 0.82 and 0.53, respectively. The proposed devices also show broadband focusing behavior from 28 GHz to 40 GHz. We provide the measured and simulated intensity profiles for operation at 30 GHz in Figure S3.
Conclusion
We have presented a platform combining an inverse electromagnetic design algorithm with additive manufacturing for the design and fabrication of novel millimeter-wave metadevices. The proposed methodology can be generalized to any photonic device where the desired electromagnetic behavior can be defined in terms of input and output field distributions. Although we design and demonstrate metadevices in the millimeter-wave region, due to the scalability of Maxwell’s equations, similar devices can be designed to operate in any wavelength from visible to microwave frequencies provided that low-loss dielectric materials can be additively fabricated with subwavelength feature sizes. The presented platform addresses the need for rapid versatile design and prototyping of compact, low-cost, low-loss, and broadband components that can then be easily integrated into complex electromagnetic systems.
Data availability statement
No datasets were generated or analyzed during the current study.
References
Pendry, J. B., Schurig, D. & Smith, D. R. Controlling electromagnetic fields. Science 312, 1780–1782, https://doi.org/10.1126/science.1125907 (2006).
Leonhardt, U. Optical conformal mapping. Science 312, 1777–1780, https://doi.org/10.1126/science.1126493 (2006).
Cubukcu, E., Aydin, K., Ozbay, E., Foteinopoulou, S. & Soukoulis, C. M. Subwavelength Resolution in a Two-Dimensional Photonic-Crystal-Based Superlens. Physical Review Letters 91, 207401 (2003).
Yao, J. et al. Optical Negative Refraction in Bulk Metamaterials of Nanowires. Science 321, 930–930, https://doi.org/10.1126/science.1157566 (2008).
Pendry, J. B. Negative Refraction Makes a Perfect Lens. Physical Review Letters 85, 3966–3969 (2000).
Shelby, R. A., Smith, D. R. & Schultz, S. Experimental Verification of a Negative Index of Refraction. Science 292, 77–79, https://doi.org/10.1126/science.1058847 (2001).
Fang, N., Lee, H., Sun, C. & Zhang, X. Sub Diffraction-Limited Optical Imaging with a Silver Superlens. Science 308, 534–537, https://doi.org/10.1126/science.1108759 (2005).
Yu, N. et al. Light Propagation with Phase Discontinuities: Generalized Laws of Reflection and Refraction. Science 334, 333 (2011).
Kildishev, A. V., Boltasseva, A. & Shalaev, V. M. Planar Photonics with Metasurfaces. Science 339 (2013).
Yu, N. & Capasso, F. Flat optics with designer metasurfaces. Nat Mater 13, 139–150, https://doi.org/10.1038/nmat3839 (2014).
Lin, D., Fan, P., Hasman, E. & Brongersma, M. L. Dielectric gradient metasurface optical elements. Science 345, 298 (2014).
Khorasaninejad, M., Ambrosio, A., Kanhaiya, P. & Capasso, F. Broadband and chiral binary dielectric meta-holograms. Science Advances 2 https://doi.org/10.1126/sciadv.1501258 (2016).
Zheng, G. et al. Metasurface holograms reaching 80% efficiency. Nat Nano 10, 308–312, https://doi.org/10.1038/nnano.2015.2 http://www.nature.com/nnano/journal/v10/n4/abs/nnano.2015.2.html#supplementary-information (2015).
Arbabi, A., Horie, Y., Bagheri, M. & Faraon, A. Dielectric metasurfaces for complete control of phase and polarization with subwavelength spatial resolution and high transmission. Nat Nano 10, 937–943, https://doi.org/10.1038/nnano.2015.186 http://www.nature.com/nnano/journal/v10/n11/abs/nnano.2015.186.html#supplementary-information (2015).
Qin, F. et al. Hybrid bilayer plasmonic metasurface efficiently manipulates visible light. Science Advances 2 (2016).
Staude, I. & Schilling, J. Metamaterial-inspired silicon nanophotonics. Nat Photon 11, 274–284, https://doi.org/10.1038/nphoton.2017.39 (2017).
Kuznetsov, A. I., Miroshnichenko, A. E., Brongersma, M. L., Kivshar, Y. S. & Luk’yanchuk, B. Optically resonant dielectric nanostructures. Science 354 (2016).
Li, Z., Palacios, E., Butun, S. & Aydin, K. Visible-Frequency Metasurfaces for Broadband Anomalous Reflection and High-Efficiency Spectrum Splitting. Nano Letters 15, 1615–1621, https://doi.org/10.1021/nl5041572 (2015).
Khorasaninejad, M. et al. Metalenses at visible wavelengths: Diffraction-limited focusing and subwavelength resolution imaging. Science 352, 1190–1194, https://doi.org/10.1126/science.aaf6644 (2016).
Borel, P. I. et al. Topology optimization and fabrication of photonic crystal structures. Opt. Express 12, 1996–2001, https://doi.org/10.1364/OPEX.12.001996 (2004).
Jensen, J. S. & Sigmund, O. Topology optimization for nano-photonics. Laser & Photonics Reviews 5, 308–321, https://doi.org/10.1002/lpor.201000014 (2011).
Piggott, A. Y. et al. Inverse design and demonstration of a compact and broadband on-chip wavelength demultiplexer. Nat. Photonics 9, 374, https://doi.org/10.1038/nphoton.2015.69 (2015).
Lalau-Keraly, C. M., Bhargava, S., Miller, O. D. & Yablonovitch, E. Adjoint shape optimization applied to electromagnetic design. Opt. Express 21, 21693–21701, https://doi.org/10.1364/OE.21.021693 (2013).
Sell, D., Yang, J., Doshay, S., Yang, R. & Fan, J. A. Large-Angle, Multifunctional Metagratings Based on Freeform Multimode Geometries. Nano Letters 17, 3752–3757, https://doi.org/10.1021/acs.nanolett.7b01082 (2017).
Shen, B., Wang, P., Polson, R. & Menon, R. Ultra-high-efficiency metamaterial polarizer. Optica 1, 356–360, https://doi.org/10.1364/OPTICA.1.000356 (2014).
Wang, P., Mohammad, N. & Menon, R. Chromatic-aberration-corrected diffractive lenses for ultra-broadband focusing. Scientific Reports 6, 21545, https://doi.org/10.1038/srep21545https://www.nature.com/articles/srep21545#supplementary-information (2016).
Lu, J. & Vuckovic, J. In Numerical Methods for Metamaterial Design Vol. 127 Topics in Applied Physics (ed Kenneth Diest) Ch. 6, 147–173 (Springer Netherlands, 2013).
Lu, J. & Vučković, J. Nanophotonic computational design. Opt. Express 21, 13351–13367, https://doi.org/10.1364/OE.21.013351 (2013).
Callewaert, F., Butun, S., Li, Z. & Aydin, K. Inverse design of an ultra-compact broadband optical diode based on asymmetric spatial mode conversion. Scientific Reports 6, 32577, https://doi.org/10.1038/srep32577, http://www.nature.com/articles/srep32577#supplementary-information (2016).
Zhang, Y. et al. Printing, folding and assembly methods for forming 3D mesostructures in advanced materials. Nature Reviews Materials 2, 17019, https://doi.org/10.1038/natrevmats.2017.19 (2017).
LaFratta, C. N., Fourkas, J. T., Baldacchini, T. & Farrer, R. A. Multiphoton Fabrication. Angewandte Chemie International Edition 46, 6238–6258, https://doi.org/10.1002/anie.200603995 (2007).
Maruo, S. & Fourkas, J. T. Recent progress in multiphoton microfabrication. Laser & Photonics Reviews 2, 100–111, https://doi.org/10.1002/lpor.200710039 (2008).
Liang, M. et al. A 3-D Luneburg Lens Antenna Fabricated by Polymer Jetting Rapid Prototyping. IEEE Transactions on Antennas and Propagation 62, 1799–1807, https://doi.org/10.1109/TAP.2013.2297165 (2014).
Du, G., Liang, M., Sabory-Garcia, R. A., Liu, C. & Xin, H. 3-D Printing Implementation of an X-band Eaton Lens for Beam Deflection. IEEE Antennas and Wireless Propagation Letters 15, 1487–1490, https://doi.org/10.1109/LAWP.2015.2514181 (2016).
Wu, Z., Kinast, J., Gehm, M. E. & Xin, H. Rapid and inexpensive fabrication of terahertz electromagnetic bandgap structures. Opt. Express 16, 16442–16451, https://doi.org/10.1364/OE.16.016442 (2008).
Wu, Z., Ng, W.-R., Gehm, M. E. & Xin, H. Terahertz electromagnetic crystal waveguide fabricated by polymer jetting rapid prototyping. Opt. Express 19, 3962–3972, https://doi.org/10.1364/OE.19.003962 (2011).
Acknowledgements
K.A. acknowledges support from the Office of Naval Research Young Investigator Program and the Robert R. McCormick School of Engineering and Applied Science at Northwestern University.
Author information
Authors and Affiliations
Contributions
F.C. and K.A. conceived the idea. F.C. performed inverse design and full-field electromagnetic simulations, and prepared figures. F.C., V.V. and P.K. did the experimental study of the metalenses. F.C. and A.V.S. did the experimental study of the metagratings. K.A. supervised the study. F.C. and K.A. wrote the paper. All authors discussed the results and reviewed the manuscript.
Corresponding author
Ethics declarations
Competing Interests
The authors declare that they have no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Callewaert, F., Velev, V., Kumar, P. et al. Inverse-Designed Broadband All-Dielectric Electromagnetic Metadevices. Sci Rep 8, 1358 (2018). https://doi.org/10.1038/s41598-018-19796-y
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-018-19796-y
This article is cited by
-
Broadband vectorial ultrathin optics with experimental efficiency up to 99% in the visible region via universal approximators
Light: Science & Applications (2021)
-
Mechanically reconfigurable multi-functional meta-optics studied at microwave frequencies
Scientific Reports (2021)
-
Multifunctional metaoptics based on bilayer metasurfaces
Light: Science & Applications (2019)
-
Global optimization of metasurface designs using statistical learning methods
Scientific Reports (2019)
-
Inverse design in nanophotonics
Nature Photonics (2018)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.