Environmental impacts and risks related to carbon dioxide (CO2) capture and storage (CCS) projects may have direct effects on the decision-making process during CCS site selection. This paper proposes a novel method of environmental optimization for CCS site selection using China’s ecological red line approach. Moreover, this paper established a GIS based spatial analysis model of environmental optimization during CCS site selection by a large database. The comprehensive data coverage of environmental elements and fine 1 km spatial resolution were used in the database. The quartile method was used for value assignment for specific indicators including the prohibited index and restricted index. The screening results show that areas classified as having high environmental suitability (classes III and IV) in China account for 620,800 km2 and 156,600 km2, respectively, and are mainly distributed in Inner Mongolia, Qinghai and Xinjiang. The environmental suitability class IV areas of Bayingol Mongolian Autonomous Prefecture, Hotan Prefecture, Aksu Prefecture, Hulunbuir, Xilingol League and other prefecture-level regions not only cover large land areas, but also form a continuous area in the three provincial-level administrative units. This study may benefit the national macro-strategic deployment and implementation of CCS spatial layout and environmental management in China.
Carbon dioxide (CO2) Capture and Storage (CCS) technology will not only play an important role in reducing CO2 emissions from the combustion of fossil fuels, but will also be an important option for significantly reducing direct emissions of CO2 during the production processes of many industries1,2,3,4,5,6,7. Therefore, CCS will have a significant meaning related to low carbon development and new urbanization processes in China8,9,10,11,12. In China, the term CO2 Capture, Utilization and Storage (CCUS) is much more popular than CCS because of its focus on using and storing CO2 13,14,15,16,17. In the past decade, CCS technology has experienced a rapid development, which had been proved to be a feasible and widely used technology worldwide. As an emerging new technology that can be used to combat climate change, CCS faces serious challenges such as uncertainties of reservoir properties18,19,20,21,22,23,24, high energy consumption, high investment and uncertainties of environmental risks during the process of implementation25,26,27. Particularly, the geological complexity of CCS creates uncertain environmental impacts; environmental risks restrict awareness and acceptance of CCS by government agencies and the public for this type of effective CO2 mitigation technology28,29,30.
The environmental risks of CCS mainly include environmental damage caused by CO2 leakage from geological storage sites. The prominent environmental risk is associated with potential CO2 leakage31, 32. CO2 leaks from geological storage reservoirs mainly occur when sequestered CO2 moves up to near the surface from deep subsurface, which may affect the local environment33. When CO2 is injected into underground reservoirs, the CO2 may leak through the following patterns: leaks through pores of low-permeability caprock (such as shale or mudstone); laterally leaks through unconformity (a buried erosional surface located between two formations or strata with different ages, indicating that sediment deposition was not continuous) or leakage through pores in rock; leaks through fractures in the caprock, ruptures or geological faults; leaks through wells or abandoned wells, including leakage between the cement and the outside of the casing, between the cement and the inside of the metal casing, within the cement plug itself, through deterioration (corrosion) of the metal casing, deterioration of the cement in the annulus and leakage in the annular region between the formation and the cement34, 35. The potential leakage pathways mentioned above and resulting environmental risks should be analyzed and evaluated in the pre-feasibility study of CCS sites36.
A proper site selection of CCS projects can effectively avoid potential environmental risks and improve the acceptance of those projects by government authorities and the public. Moreover, site selection is a time-consuming and daunting task37,38,39. In general, the site selection of a CCS project typically includes 2–3 phases: screening, preliminary site selection and preliminary description of the target site40,41,42. The phases used in analyzing site selection may differ slightly around the world, but the baseline content is similar43,44,45,46. The first step in site selection involves screening of suitable regions against specific suitability criteria along with a more or less parallel assessment of storage capacity47,48,49. The site selection of a CCS project described here includes screening at either the national level or a sedimentary basin level, which focuses on a screening framework of environmental indicator construction and regional environmental analysis. This stage does not consider source-sink matching. Bachu1 proposed a systematic approach for the assessment and selection of methods and sites for CO2 sequestration in geological media. The basin selection criteria could be classified into geological, hydrodynamic and geothermal, hydrocarbon potential and basin maturity, economic and political and societal categories. Then, a roadmap for site selection using the transform of the geological space into the CO2 phase space was proposed based on a geoscience based analysis that includes suitability, inventory, safety and capacity50. In addition, a set of 15 criteria with several classes was developed for the assessment and ranking of sedimentary basins in terms of their suitability for CO2 sequestration. A basin’s individual scores are summed to a total score using weights that express the relative importance of different criteria using a parametric normalization procedure37. This screening methodology has been widely adopted and modified by researchers worldwide51,52,53,54, and this method has been successfully applied in some cases in China45, 55. Damen, et al.56 performed a study to identify potential worldwide opportunities for the early application of CO2 sequestration by using a Geographical Information System (GIS) to combine worldwide CO2 point sources with oil and coal fields. They defined an early opportunity as a situation including high-purity CO2 point source that provides CO2 at low costs to oil or coal fields with the goal of enhancing oil production or coal bed methane production, at a site where CO2 is simultaneously sequestered. Li, et al.57 ranked the aquifer storage sites in Japan in terms of potential CO2 storage capacity and potential CO2 supply, both of which significantly affect the storage economics. Meyer, et al.58 reported on regional screening, site selection and geological characterization of a potential storage site in northeastern Germany while considering the capacity limit for pipeline transport distance of up to about 300 km based on economic reasons. Oldenburg38 developed a screening and ranking framework for CO2 geological storage on based on health, safety, and environmental (HSE) risk arising from CO2 leakage. That framework did not explicitly consider the environmental concerns such as national parks and human distribution. Li, et al.59 applied a slightly revised screening and ranking framework based on HSE risk that was developed by Oldenburg38 to evaluate the risk of leakage for China’s first full-chain Shenhua CCS demonstration site in the Ordos Basin. Grataloup, et al.60 proposed a site selection method with different objectives, such as storage optimization and risk minimization, with respect to regulations and spatial constraints, gave full consideration to the social and economic aspects of CCS. The corresponding criteria were classified into “killer criteria” and “site-qualification criteria”. This multi-criteria method was applied on the PICORE study area by a GIS tool. The GIS tool was also used in the METSTOR project in France to look for potential CO2 storage zones based on an interactive map of the CO2 storage capacities of various sites61. Mathias, et al.47 presents a simple method for estimating pressure buildup caused by the injection of supercritical CO2 into a saline formation, and the limiting pressure of fracking in the target formations. Such a method will be useful for screening and selecting sites for CO2 sequestration with the goal of identifying sites that are worthy of further investigation. Ramírez, et al.53 used the main aspects of multi-criteria analysis in a linear aggregation tool as a method used to screen and rank off- and on-shore reservoirs suitable for long-term large scale CO2 storage in the Netherlands. The screening of storage options was based on a set of three criteria, i.e. potential storage capacity, storage costs and the amount of effort needed to manage the risk involved. Hsu, et al.62 proposed an analytic network process approach for the selection of potential sites for CO2 geological storage as a basis for further geological feature exploration and the simulation of transport characteristics. A multi-criteria decision model with eight evaluation criteria was proposed with the consideration of site selection as a complex multi-criteria decision-making problem. Raza, et al.63 presented a general criterion based on local-scale projects under the consideration of storage capacity, injectivity, trapping mechanisms, containment and cost. A group of key parameters including reservoir and well types, classes of minerals, residual gas and water saturations, subsurface conditions, rock types, wettability, properties of CO2, and sealing potentials were analyzed to provide an insight into the suitable selection of storage sites.
It is important to clarify that the aforementioned research on CCS site screening did not fully consider environmental constraints, but was more focused on the potential for underground sequestration and related economic factors. Wei, et al.64 developed a preliminary sub-basin scale evaluation framework of site suitability for onshore aquifer-based CO2 storage in China based on a multi-criteria analysis framework, which considers four objectives: storage optimization, risk minimization and storage security, environmental restrictions regarding surface and subsurface use and economic considerations. That study used GIS-based evaluation tool to conduct the application of the framework. In their research, only three environmental restrictions regarding existing surface and subsurface use were considered. These included the proximity of cities, the distribution of natural resources and coal resources as well as the distance from the CCS site to existing deep coal mines. That study also implemented a screening framework to reflect potential damage or economic impacts to the geological or terrestrial environment. The government of China attaches great importance to environmental impacts and risks related to CCS technology. On 20th June 2016, the Ministry of Environmental Protection of the People’s Republic of China issued Technical Guidelines on Environmental Risk Assessment for Carbon Dioxide Capture, Utilization and Storage (on Trial)65. The authors of this paper were major participants in the formulation of these guidelines. While considering the supervision of the government of China of environmental impacts and risks of a CCS project, the present paper first proposes an environmental optimization method for CCS site selection that mirrors the method of delineation of China’s ecological red line. In addition, this paper establishes a GIS spatial analysis model of environmental optimization for CCS site selection, and carries out a detailed analysis of CCS site selection in China based on environmental optimization.
The ecological red line system (ERLS), initiated in 2013, provides one of the important set of environmental management standards and guidelines in China and designates areas to be protected from human activities66, 67. The ERLS has been stressed by the Communist Party of China (CPC) in the third Plenary Session of the 18th CPC Central Committee, and marks a great breakthrough in environment protection in China. In 2015, the Ministry of Environmental Protection of the People’s Republic of China promulgated a Technical Guideline for Ecological Protection Red Line Delineation ( No. 56) to improve the implementation and delineation methods of ecological red line designation66. The ERLS plays a very important role in the protection of ecological resources, ecologically fragile zones, and biodiversity in China68. The essence of the ERLS is to spatially divide the human land management and activities into different regions, so as to achieve a desirable level of ecological protection for ecosystems. By combining bottom-up with top-down management characteristics in China, the ERLS continues to play an increasingly important role in environment management in China.
Enlightened by the methods and procedures provided in the ERLS, this paper established a spatial model to identify and evaluate the degree of suitability for the implementation of CCS projects in different regions of China, so as to provide a reference for the government’s policy-making and regional layout of CCS projects. Below, Section 2 describes the method and data used for site-specific screening. Section 3 shows the results of the assessment and analysis while Sections 4 provides policy proposals and a discussion of the findings.
Methods and Data
Environmental elements and indices
CO2 leakage from a human-created storage location may be harmful to human health and create negative effects to ecosystems, soils, and groundwater, etc. (Table 1). The leaked CO2 dissolved in the groundwater could induce the motivation of some toxic metal element69, 70. There may also be acidification of soils and displacement of oxygen in soils. Additionally, if leakage to the atmosphere, CO2 may lead to a suffocation of humans or animals, or effect on plants above ground71.
The environmental effects and risks of CCS have caused the United States, European Union, Australia and other developed countries to formulate environmental regulations and provisions to protect ecosystems from the national level, including water sources, groundwater and human health, etc. The Ministry of Environmental Protection of the People’s Republic of China promulgated the Technical Guidelines on Environmental Risk Assessment for Carbon Dioxide Capture, Utilization and Storage, which categorized risk receptors in the CCS environmental assessment as the human population, animals and plants and other life forms and closely related groundwater, surface water, air, soil and other environmental media65, 72, 73. In addition, China has been implementing similar regulations which could be referenced by the site selection criteria of CO2 geological storage, such as the Standards for Pollution Control on the Security Landfill Site for Hazardous Wastes (GB 18598-2001/XG1-2013)74 and the Standards for Pollution Control on the Landfill Site of Municipal Solid Waste (GB 16889-2008)75, etc. The above standards proposed restriction and prohibition requirements for site selection. Considering standards and guidelines of environmental elements (Fig. 1) mentioned above, this paper identified water resource (groundwater and surface water), vegetation and human health as the major environmental elements affected by the environmental risks and environmental impacts of CO2 geological storage. Compared with these elements, other elements are less affected (Table 1). Therefore, during optimization of the environmental impact for the site selection process for CO2 geological storage sites, it is important to consider the characteristics and vulnerability of water resources, vegetation, wildlife, and human health in target areas of CCS projects. In addition, China has strategically implemented sustainable development plans related to main function zoning and ecological function zoning, which forms an important macro guidance plan for China’s economic development and environmental protection. The environmental risks of CO2 geological storage require that site selection must meet the requirements of the state’s macro spatial planning, i.e. China’s main function zoning and the national ecological function division planning. Table 2 describes main environmental elements affected by CO2 geological storage, and elaborates the characterization of indices for environmental elements.
Based on the methods and techniques in the Technical Guideline for Ecological Protection Red Line Delineation ( No. 56), multi-factor analysis and GIS spatial analysis, this paper attempts to determine how to build a spatial evaluation model for CCS site selection with a focus of environment optimization (Fig. 2). The ERLS has a good solution for weight assignments for different indicators, without considering duplication between the indicators. This method defines the importance of each evaluation region based on the most important environmental elements in the region. The quartile method is used for value assignment for specific indicators. This type of statistical analysis is used to describe the data, especially the degree of dispersion for skewed data. The data are arranged in ascending order and then are divided into four equal parts so that each part of the data volume account for 25% of entire data volume. The first quartile, also known as the “lower quartile,” is equal to the smallest 25% of all data. The second and third quartiles, also known as “median”, are equal to 50% data of all data. The fourth quartile, also known as “upper quartile”, equal to the largest 75% of all data. A suitable CCS site may be selected based on the spatial model. Meanwhile, various types of information are analyzed based on the site suitability and characteristics while using case studies to verify the suitability of an area. The spatial boundary of suitable CCS sites and related detailed records will ultimately be created. The GIS spatial analysis model used here allows a thorough analysis of the identification of optimal environments for CO2 geological storage, including the projection and conversion of the original data, buffer analysis using point distribution data, conversion of data from vector to raster format, re-sampling of raster data, quartile classification operations by ArcMap Quantile functions, and spatial calculations. The maps in Figs 2–4, 9, 10 were generated by software ArcGIS 9.2 based on our own data. The China spatial boundary GIS data is from the National Geomatics Center of China (affiliated with National Administration of Surveying, Mapping and Geoinformation of China), which provides the basic GIS data for China.
The basic data required for the model employed in this paper included two parts: suitability evaluation results of CO2 geological storage in sedimentary basins and basic data related to optimal site selection based on environmental issues in China (Table 3 and Fig. 3). Sedimentary basins are considered as suitable sites for CO2 geological storage for the stable structure with the large capacity and well injectivety. Some pilot projects have been constructed and operated in the sedimentary basins, such as Shenhua CCS project in Ordos basin. Additionally, lots of oil and gas fields distrusted in basins provide potential sites for CO2-EOR, CO2-EGS, or CO2 storage in depleted oil or gas fields. For example, the Songliao basin has been proved to have large storage capacity in deep saline aquifers with good reservoir-caprock properties76, moreover, several CO2-EOR experiments have been carried out in the basin since the 1960, and the theoretical storage capacity of CO2 in the oilfields of the Basin is large to 2.36 × 109t77.
We synthetically considered the two evaluation results of CO2 geological storage suitability, issued by the Wuhan Institute of Rock and Soil Mechanics, Chinese Academy of Sciences (WHRSM) and the China Geological Survey Center for Hydrogeology and Environmental Geology Survey (CHEGS). Both results were very similar (Fig. 3) under the same assumption used for the analytic hierarchy process assessment. However, the conclusion of WHRSM was more sophisticated in detail. Through our integrated assessment and consideration, we tend to accept WHRSM assessment results. WHRSM applied four indices, including seismic intensity for crust stability, terrestrial heat flow for geothermal geological conditions of seismic intensity, crater and active faults, and a suitability evaluation conducted for sedimentary basins of CO2 geological storage in China (CAGS1 internal report, 2012)78. The present report divides the evaluation results of suitability into five categories: not suitable, low suitability, normal suitability, high suitability, and very suitable. Most inland sedimentary basins in China are suitable for CO2 geological storage. Areas with active faults and volcanoes such as part of the minority region in the northwestern Ordos and southern Songliao basins are not suitable for CO2 geological storage. Basic data of environmental elements include GIS data of surface water, centralized drinking water source protection areas, nature reserves, national forest parks, national parks of China, and national key ecological function areas. Basic data were organized in the Geodatabase during spatial analysis and pre-processing. The spatial resolution of data was uniformly set to 1 km to facilitate analysis with the spatial model. The environmental suitability of a grid unit was determined as the minimum rating value of the indices. The specific data are shown in Table 3 and Fig. 3.
Data availability statement
The data used in this study may be limitedly or full accessed by contacting the corresponding author.
Results and Discussion
The suitability results of environmental optimization of site selection for CCS in China can be obtained based on the analysis and evaluation of the spatial model employed (Fig. 4). Four categories of suitability classes were developed, i.e. classes I, II, III, and IV. Areas identified as suitability class I are prohibited regions, i.e. regions that are completely unsuitable for carrying out CCS projects. The suitability of classes II, III, and IV indicates that the environmental suitability of a CCS site selection has successively increased. From an environmental perspective, suitability class IV regions are relatively ideal areas for CCS projects. Most regions with a high environmental suitability (classes III and IV) in China are located in western China, and are concentrated in Xinjiang Uyghur Autonomous Region (Xinjiang; Fig. 4). The CCS site selection in eastern China may be greatly affected by the indices of population distribution and population activity intensity. In China’s western region, the CCS site selection may be affected by indices such as the ecological function zoning. Because prohibited areas for CCS sites such as water bodies, national forest parks, and nature reserves are relatively dispersed in China, the CCS site selection should reasonably avoid these areas after field surveys are completed.
Several basins provide ideal regions for CO2 geological storage with good environmental suitability including the central Tarim, northern Qaidam, northern Junggar, and the central Turpan-Hami basins as well as the northern margins of the Ordos and Erlian basins, and the western margin of the Hailar Basin. In particular, the central Tarim, the northern Qaidam, and the northern Junggar basins have larger areas available for CCS with strong environmental suitability. The primary trap of a structural unit in the Tarim Basin has a large potential for geological storage of CO2 64, 79, 80, and the region is mainly located in the Kuqa depression, north depression and the central uplift area. These three target areas may be treated as the main site of CCS projects in the future as because they are also close to the oil and gas reservoirs in the Tarim Basin.
Less suitable sites for CCS in the western margin of the Tarim and Erlian basins, the central Hailar Basin, and the central Ordos Basin based on the environmental constraints of the main function zones. These include areas such as the Tarim River desertification control and ecological area, Yinshan mountain grassland, the Hulunbuir grassland-meadow, and the water and soil conservation areas of the Loess Plateau. Areas that provide only very limited suitability for CCS in the southern Junggar Basin because they are restricted by national ecological function zoning include important regions of water and biodiversity conservation in the Tianshan, and important regions of biodiversity conservation and sand-fixing in the western and eastern Junggar Basin.
Characteristics of suitable regions
The areas that are most suitable for CCS (class IV) in China cover a total area of 620,800 km2 (Table 4) and most of these areas are located in Xinjiang. Xinjiang includes 483,700 km2 of suitability class IV, accounting for 78% of the total area of suitability class IV. Qinghai Province includes an area of 86,400 km2 of suitability class IV, or 14% of the total area in class IV. Inner Mongolia Autonomous Region (Inner Mongolia) covers 42,200 km2 of suitability class IV, with 7% of the total. The regions in suitability class IV in Xinjiang, Qinghai and Inner Mongolia account for 99% of the country’s total area in this class (Fig. 5).
The areas of environmental suitability class III cover 156,600 km2 (Fig. 6), with most of this area lying in Inner Mongolia which has 82,200 km2 and 52% of the total area in suitability class III. Xinjiang has 34,300 km2 (22%) in class III while Qinghai Province has 13,660 km2 (9%). The combined area of Inner Mongolia, Xinjiang, and Qinghai in class III accounts for 83% of the total area of suitability class III.
From an environmental perspective, the regions of suitability class III and IV will be the ideal regions for CCS projects. Therefore, from a macro perspective, the Xinjiang, Qinghai, and Inner Mongolia region, usually called the Big Three region as one collective environment-friendly region for CCS in China, are regarded as the first priority region for strategic deployment of China’s CCS projects. In particular, the Big Three region is well aligned with the location of China’s coal chemical industry planning during the past decade81, 82 and early planning for CO2 enhanced water recovery technology announced during the China-U.S. Joint Announcement on Climate Change and Clean Energy Cooperation released on November 11, 201483, 84.
Vegetation net primary production (NPP), population density and the intensity of the activity of the population are important quantitative indices used during the evaluation of environmental suitability for CCS site selection. Based on the statistical characteristics of various environmental elements of evaluated regions within different classes of suitability (Figs 7 and 8), the analysis results show that regions with relative high environmental suitability (classes III and IV) have relatively low NPP and population density. Regions with the lowest environment suitability (class I) exhibit the highest values for both the maximum and median values of NPP and population density. As for environmental suitability class IV, the statistical distribution of NPP values shows a significant bimodal phenomenon, indicating that this class of region may have two different types of vegetation or quite different land cover types. However, generally speaking, class IV regions have relatively lower NPP compare to other regions.
The probability density curves of the population density have shown multiple peaks in the four classes of environmental suitability regions (Fig. 8). This statistical characteristic indicates that the regions for environmental suitability can still be divided further into sub-regions based on population density or urbanization and economic development, and knowing this will provide more sophisticated guidance for the spatial layout and site selection of CCS projects.
Prefecture-level regions constitute the second level of the administrative structure in China, ranking below provinces and above counties. Considering the relatively manageable area and more powerful governing capacity by means of regulations and standards than counties, prefecture-level regions are regarded to be more fundamental and flexible in carbon mitigation and policy implementation compared to provinces and counties. Considering the region of environmental suitability class IV is the first priority for the selection of sites for CCS projects, this section is focused on the distribution of environmental suitability class IV in Chinese prefecture-level regions.
The spatial extent of environmental suitability class IV is far less than 500 km2 in the majority of Chinese prefecture-level regions. These areas are spatially fragmented and are not favorable as locations for CO2 geological storage projects. Three sedimentary basins, i.e. Tarim, Junggar, and Turpan-Hami, in Xinjiang have rich oil and gas resources. The geological conditions and geological processes for hydrocarbon accumulations in these three basins determine whether or not the reservoirs have good geological traps and reservoir-caprock combinations. Meanwhile, environmental elements which constrain the deployment of CCS projects are relatively fewer. Therefore, Xinjiang has the largest area with good environmental suitability for sites of CCS projects. In Xinjiang, three prefecture-level regions including Bayingol Mongolian Autonomous, Hotan, and Aksu prefectures not only have a large area with a continuous distribution for potential CCS sites with environmental suitability class IV, this region also has a high proportion (56%) of the total class IV area in China (Fig. 9).
Western Hulunbuir of Inner Mongolia has single area of 9,900 km2 of environmental suitability class IV for CCS site selection while eastern Xilingol League has about 26,400 km2. Meanwhile, northern Ordos has about 5,200 km2 and Qinghai Haixi Mongolian-Tibetan Autonomous Prefecture has about 86,300 km2. A single area ranked as class IV in eastern Jiuquan City covers about 4,400 km2, while the class IV area in Yulin and Yan’an in northern Shaanxi Province is more dispersed, with a total area of 145 km2.
Validation for the target area of the Yanchang CCUS project
This section analyzes the appropriateness of environmental suitability division for China’s CCS site selection by using the pilot site, the Yanchang CCUS project in the Ordos Basin, China, as a case study. The full name of the Yanchang CCUS project is the Shaanxi Yanchang Petroleum CO2 capture, utilization and storage project. The Chinese scientists and government regulators believes this CO2 enhanced oil recovery (CO2-EOR) demonstration project is very important. In 2015, the Yanchang Petroleum Jingbian CCUS project passed international certification of the Carbon Sequestration Leadership Forum (CSLF), which became the first independently certified CCS project in China. On 25th September 2015, the U.S.-China Joint Presidential Statement on Climate Change made it clear that the CCUS project mentioned in the U.S.-China Joint Announcement on Climate Change in 2014 will be determined in Yanchang oilfield. In addition, the potential site will be selected in the Yan’an-Yulin area. The Yanchang Petroleum Jingbian CCUS project is located at Qiaojiawa Village, Xiaohe Township, Jingbian County, Shaanxi Province85. The project began in 1st January 2012, and the deadline for releasing the results of the first phase of the research was 30th April 2015. CO2 injection started on Sept. 4th, 2012 with twenty-ton tanker trucks used to transport CO2 during the first phase. The CO2 sources of the Yanchang Petroleum Jingbian CCUS project were purchased from the Xingping fertilizer plant in the western part of Xi’an before the Yulin coal chemical facility with CO2 capture ability of 50,000 tons per year was put into production by Yanchang Petroleum in 201286. By the end of 2015, the total CO2 injection volume reached to 55,000 tons. This CCUS project is located in the Ordos Basin in the north central area of slope of northern Shaanxi, an area with stable regional tectonic conditions and free of large-scale tectonic activity and faults85, 87. Therefore, the geological structure of this region is stable and the occurrence of CO2 leakage caused by large scale tectonic activity or fracturing is relatively low. The Yanchang CCUS project is located in a region of suitability class III (Fig. 10) and the environmental sensitivity of this site is rather low. However, from the regional point of view, the environmental suitability class III of this region is fragmented in scope and water resources protection areas exist in the northwest. Therefore, the next phase of CO2 injection and other activities in this region need to fully consider the nearby environmental elements and conducting an environmental risk assessment is necessary.
As one of the important mitigation measures for global greenhouse gas emissions, CCS technology is attracting a great amount of attention and has been developing rapidly in China. However, environmental risks and impacts of CCS projects have not yet been fully considered by the government and members of the public in China. By analyzing the on-the-ground situation and characteristics of China’s environmental management techniques, this paper uses the ecological red line as a reference, and analyzed the environmental suitability of CCS projects in China based on big data related to basic environmental issues in China. The results showed that regions of suitability classes III and IV, with very good environmental suitability for CCS projects, cover about 620,800 and 156,600 km2, respectively, and are mainly in three provinces in China, i.e. Xinjiang Uyghur and Inner Mongolia autonomous regions and Qinghai Province. In these three regions, the area of suitability class IV, the highest environmental suitability class not only accounts for a large land area, but also forms a continuous unit. These include in Bayingol Mongolian Autonomous Prefecture, Hotan Prefecture, Aksu Prefecture, Hulunbuir, Xilingol League and other prefecture-level regions. This large area may favor the deployment and implementation of CCS projects. In China, the current CCS projects are mainly considered CO2 emission sources and entail economic costs, e.g. Shenhua CCS and Yanchang CCUS. These have not placed adequate emphasis on environmental concerns. Along with the accumulation of experience and technical progress of China’s CCS pilot and demonstration projects, China is gradually considering the planning and deployment of CCS strategically at the national level. This study provides timely and strong support of the spatial layout and environmentally-sound management of CCS projects for decision-makers.
Xinjiang, Qinghai and Inner Mongolia and other western provinces have large areas with optimal environmental suitability for CCS site selection and projects where would have relatively little environmental impact. Furthermore, these regions are currently experiencing a large amount of oil and gas exploration as well as support coal and chemical-related industries. Therefore, the strategic deployment of a national level CCS can prioritize these regions.
The region with the highest potential for acceptable environment suitability for CCS site selection in China is mainly located in the west. However, the largest emission sources in China mainly occur in the east. Environmentally suitable areas for CCS sites do not spatially match with large CO2 emission sources, which create considerable difficulty for CCS planning. On this point, the establishment of a national CCS management network may resolve the problem to a certain degree in the future. Considering transportation costs of CCS projects, although some eastern regions that are close to large CO2 emission sources are less suitable for CSS, these areas should be given our full attention during the careful selection of potential CCS sites. It is appropriate to choose ocean-based geological storage if no on-shore sites are available.
The process of environmental analysis and management during the CCS site selection needs to be strengthened further. The present study was conducted on the national level. The strategic layout for CCS projects in different regions should not only consider the emission sources and economic costs, but should also fully account for environmental issues. In addition, the aforementioned analysis shows that the environmental issues still have large ramifications even for regions with the same level of suitability. Therefore, the refinement of spatial environmental management and further analysis are also crucial.
The present study started by referring to the standard technology and methods provided in China’s ecological red line assessment, which minimizes the need for subjective analysis and assessment. Next, after collecting and analyzing vast amounts of environmental data in as much detail as possible, we carried out model calculations on geographical units with a high spatial resolution. However, future work should still provide some improvements on the baseline established here as follows. (a) Regional differences of environmental elements are considered inadequate for spatial modeling on a national scale. Therefore, our research group plans to consider more precise assessments for each sub-region as the next step. (b) The accuracy of some of the data needs to be improved. For example, some nature reserves were only considered based on the location of the center of reserves and the land areas covered. Therefore, the actual spatial boundaries had to be substituted by a circle in the model used here. (c) It is very necessary to consider source-sink matching characteristics at a regional level, so as to further refine the sequestration potential for regions that are environmentally suitable for CCS projects, and to enhance the analysis of the integrated CCUS system. (d) The input data should be further refined to the level of municipal administrative units. It is crucial to provide a reference of CCUS site selection and make this available for local environmental protection departments.
Bachu, S. Sequestration of CO2 in geological media: Criteria and approach for site selection in response to climate change. Energ. Convers. Manage 41, 953–970 (2000).
Celia, M. A., Nordbotten, J. M., Bachu, S., Kavetski, D. & Gasda, S. Summary of Princeton Workshop on Geological Storage of CO 2 . 60 (Princeton University, 2005).
Holloway, S., Pearce, J. M., Hards, V. L., Ohsumi, T. & Gale, J. Natural emissions of CO2 from the geosphere and their bearing on the geological storage of carbon dioxide. Energy 32, 1194–1201, doi:10.1016/j.energy.2006.09.001 (2007).
Gale, J. Why do we need to consider geological storage of CO2. Geological Society, London, Special Publications 233, 7–15, doi:10.1144/gsl.sp.2004.233.01.02 (2004).
Chu, S. Carbon Capture and Sequestration. Science 325, 1599, doi:10.1126/science.1181637 (2009).
Yan, J. Carbon Capture and Storage (CCS). Appl. Energ. 148, A1–A6, doi:10.1016/j.apenergy.2015.03.019 (2015).
de Coninck, H. & Bäckstrand, K. An International Relations perspective on the global politics of carbon dioxide capture and storage. Global. Environ. Chang. 21, 368–378, doi:10.1016/j.gloenvcha.2011.03.006 (2011).
Li, Q., Wei, Y.-N. & Dong, Y. Coupling Analysis of China’s Urbanization and Carbon Emissions: Example from Hubei Province. Nat. Hazards 81, 1333–1348, doi:10.1007/s11069-015-2135-6 (2016).
Liu, L.-C., Wu, G., Wang, J.-N. & Wei, Y.-M. China’s carbon emissions from urban and rural households during 1992–2007. J. Clean. Prod. 19, 1754–1762, doi:10.1016/j.jclepro.2011.06.011 (2011).
Cai, B. F. & Zhang, L. X. Urban CO2 emissions in China: Spatial boundary and performance comparison. Energ. Policy 66, 557–567, doi:10.1016/j.enpol.2013.10.072 (2014).
Martínez Arranz, A. Hype among low-carbon technologies: Carbon capture and storage in comparison. Global. Environ. Chang. 41, 124–141, doi:10.1016/j.gloenvcha.2016.09.001 (2016).
Wang, K., Lu, B. & Wei, Y. M. China’s regional energy and environmental efficiency: A range-adjusted measure based analysis. Appl. Energ. 112, 1403–1415, doi:10.1016/j.apenergy.2013.04.021 (2013).
Gale, J. CO2 utilisation. Int. J. Greenhouse Gas Control 19, 1–2, doi:10.1016/j.ijggc.2013.08.006 (2013).
Li, X. C., Zhang, J. T., Wei, W. & Huang, K. Y. An overview on the special issue – The assessment of CO2 utilization technology in China. J. CO 2 Util. 11, 1–2, doi:10.1016/j.jcou.2015.03.001 (2015).
Zhang, X., Fan, J.-L. & Wei, Y.-M. Technology roadmap study on carbon capture, utilization and storage in China. Energ. Policy 59, 536–550, doi:10.1016/j.enpol.2013.04.005 (2013).
Li, L., Zhao, N., Wei, W. & Sun, Y. A review of research progress on CO2 capture, storage, and utilization in Chinese Academy of Sciences. Fuel 108, 112–130, doi:10.1016/j.fuel.2011.08.022 (2013).
Oldenburg, C. M. Why we need the ‘and’ in ‘CO2 utilization and storage’. Greenh. Gases 2, 1–2, doi:10.1002/ghg.1274 (2012).
Ampomah, W. et al. Evaluation of CO2 Storage Mechanisms in CO2 Enhanced Oil Recovery Sites: Application to Morrow Sandstone Reservoir. Energ. Fuel. 30, 8545–8555, doi:10.1021/acs.energyfuels.6b01888 (2016).
Ampomah, W. et al. Performance assessment of CO2-enhanced oil recovery and storage in the Morrow reservoir. Geomech. Geophys. Geo-energ. Geo-resour. doi:10.1007/s40948-017-0059-1 (2017).
Ampomah, W. et al. Optimum design of CO2 storage and oil recovery under geological uncertainty. Appl. Energ. 195, 80–92, doi:10.1016/j.apenergy.2017.03.017 (2017).
Ampomah, W. et al. Co-optimization of CO2-EOR and storage processes in mature oil reservoirs. Greenh Gases 7, 128–142, doi:10.1002/ghg.1618 (2017).
Dai, Z. X. et al. Uncertainty quantification for CO2 sequestration and enhanced oil recovery. In 12th International Conference on Greenhouse Gas Control Technologies, Vol. 63 Energy Proc. (eds T. Dixon, H. Herzog, & S. Twinning) 7685–7693 (Elsevier Science Bv, 2014).
Dai, Z. X. et al. CO2 Accounting and Risk Analysis for CO2 Sequestration at Enhanced Oil Recovery Sites. Environ. Sci. Technol. 50, 7546–7554, doi:10.1021/acs.est.6b01744 (2016).
Pan, F. et al. Uncertainty analysis of carbon sequestration in an active CO2-EOR field. Int. J. Greenhouse Gas Control 51, 18–28, doi:10.1016/j.ijggc.2016.04.010 (2016).
Stigson, P., Hansson, A. & Lind, M. Obstacles for CCS deployment: an analysis of discrepancies of perceptions. Mitig. Adapt. Strateg. Glob. Chang. 17, 601–619, doi:10.1007/s11027-011-9353-3 (2012).
Li, J., Liang, X., Cockerill, T., Gibbins, J. & Reiner, D. Opportunities and barriers for implementing CO2 capture ready designs: A case study of stakeholder perceptions in Guangdong, China. Energ. Policy 45, 243–251, doi:10.1016/j.enpol.2012.02.025 (2012).
Bachu, S. CO2 storage in geological media: Role, means, status and barriers to deployment. Prog. Energ. Combust. 34, 254–273, doi:10.1016/j.pecs.2007.10.001 (2008).
Chen, Z.-A. et al. A large national survey of public perceptions of CCS technology in China. Appl. Energ. 158, 366–377, doi:10.1016/j.apenergy.2015.08.046 (2015).
Liang, X., Reiner, D. & Li, J. Perceptions of opinion leaders towards CCS demonstration projects in China. Appl. Energ. 88, 1873–1885, doi:10.1016/j.apenergy.2010.10.034 (2011).
Ashworth, P., Wade, S., Reiner, D. & Liang, X. Developments in public communications on CCS. Int. J. Greenhouse Gas Control 40, 449–458, doi:10.1016/j.ijggc.2015.06.002 (2015).
Oldenburg, C. M. Improved understanding of geologic CO2 storage processes requires risk-driven field experiments. Greenh. Gases 1, 191–193 (2011).
Liu, L.-C., Li, Q., Zhang, J.-T. & Cao, D. Toward a framework of environmental risk management for CO2 geological storage in China: Gaps and suggestions for future regulations. Mitig. Adapt. Strateg. Glob. Chang. 21, 191–207, doi:10.1007/s11027-014-9589-9 (2016).
Koornneef, J., Ramirez, A., Turkenburg, W. & Faaij, A. The environmental impact and risk assessment of CO2 capture, transport and storage - An evaluation of the knowledge base. Prog. Energ. Combust. 38, 62–86, doi:10.1016/j.pecs.2011.05.002 (2012).
Metz, B., Davidson, O., de Coninck, H., Loos, M. & Meyer, L. IPCC 2005: IPCC Special Report on Carbon Dioxide Capture and Storage 431 (Cambridge University Press, Cambridge, England, UK, 2005).
Birkholzer, J. T., Oldenburg, C. M. & Zhou, Q. CO2 migration and pressure evolution in deep saline aquifers. Int. J. Greenhouse Gas Control 40, 203–220, doi:10.1016/j.ijggc.2015.03.022 (2015).
Li, Q. & Liu, G. Risk assessment of the geological storage of CO2: A review. In Geologic Carbon Sequestration: Understanding Reservoir Behavior (eds V. Vishal & T. N. Singh) 249–284 (Springer, 2016).
Bachu, S. Screening and ranking of sedimentary basins for sequestration of CO2 in geological media in response to climate change. Environ. Geol. 44, 277–289, doi:10.1007/s00254-003-0762-9 (2003).
Oldenburg, C. M. Screening and ranking framework for geologic CO2 storage site selection on the basis of health, safety, and environmental risk. Environ. Geol. 54, 1687–1694, doi:10.1007/s00254-007-0947-8 (2008).
Zheng, Z., Larson, E. D., Li, Z., Liu, G. & Williams, R. H. Near-term mega-scale CO2 capture and storage demonstration opportunities in China. Energ. Environ. Sci. 3, 1153–1169 (2010).
GCCSI. Large - Scale CCS Projects - Definitions: Asset lifecycle Definition, http://www.globalccsinstitute.com/projects/large-scale-ccs-projects-definitions (2015).
Det Norske Veritas. Geological storage of Carbon Dioxide. Report No. DNV-RP-J203, 56 (2012).
Canadian Standards Association. CSA Z741-12 Geological storage of carbon dioxide (Mississauga, Ontario, 2012).
NETL. Best Practices: Site Screening, Selection, and Initial Characterization for Storage of CO 2 in Deep Geologic Formations. 110 (National Energy Technology Laboratory, 2010).
CO2CRC. Storage Capacity Estimation, Site Selection and Characterisation for CO 2 Storage Projects. 52 (Cooperative Research Centre for Greenhouse Gas Technologies, Canberra, Australia, 2008).
Administrative Center for China’s Agenda 21 & Center for Hydrogeology and Environmental Geology. Research on the guideline for site selection of CO 2 geological storage in China (Geological Publishing House, 2012).
Det Norske Veritas. CO2QUALSTORE: Guideline for Selection and Qualification of Sites and Projects for Geological Storage of CO 2 . 77 (Det Norske Veritas, Hovik, Norway, 2009).
Mathias, S. A., Hardisty, P. E., Trudell, M. R. & Zimmerman, R. W. Screening and selection of sites for CO2 sequestration based on pressure buildup. Int. J. Greenhouse Gas Control 3, 577–585, doi:10.1016/j.ijggc.2009.05.002 (2009).
Friedmann, S. J. Site characterization and selection guidelines for geological carbon sequestration. 29 (Lawrence Livermore National Laboratory, Livermore, CA, USA, 2007).
Delprat-Jannaud, F. et al. State of the Art review of CO 2 Storage Site Selection and Characterisation Methods. 116 (CO2GeoNet - The European Network of Excellence on the Geological Storage of CO2, France, 2013).
Bachu, S. Sequestration of CO2 in geological media in response to climate change: Road map for site selection using the transform of the geological space into the CO2 phase space. Energ. Convers. Manage. 43, 87–102, doi:10.1016/S0196-8904(01)00009-7 (2002).
Liu, G. & Li, Q. A basin-scale site selection assessment method for CO2 geological storage under the background of climate change. Climate Change Res. Lett. 3, 13–19, doi:10.12677/ccrl.2014.31003 (2014).
Li, Q., Kuang, D., Liu, G. & Liu, X. Acid Gas Injection: A Suitability Evaluation for the Sequestration Site in Amu Darya Basin, Turkmenistan. Geol. Rev. 60, 1133–1146 (2014).
Ramírez, A., Hagedoorn, S., Kramers, L., Wildenborg, T. & Hendriks, C. Screening CO2 storage options in the Netherlands. Int. J. Greenhouse Gas Control 4, 367–380, doi:10.1016/j.ijggc.2009.10.015 (2010).
Rodosta, T. D. et al. U.S. Department of energy’s site screening, site selection, and initial characterization for storage of CO2 in deep geological formations. Energy Proc. 4, 4664–4671, doi:10.1016/j.egypro.2011.02.427 (2011).
Wu, X. Carbon Dioxide Capture and Geological Storage: The First Massive Exploration in China 363 (Science Press, Beijing, 2013).
Damen, K., Faaij, A., van Bergen, F., Gale, J. & Lysen, E. Identification of early opportunities for CO2 sequestration—Worldwide screening for CO2-EOR and CO2-ECBM projects. Energy 30, 1931–1952, doi:10.1016/j.energy.2004.10.002 (2005).
Li, X. C., Ohsumi, T., Koide, H., Akimoto, K. & Kotsubo, H. Near-future perspective of CO2 aquifer storage in Japan: Site selection and capacity. Energy 30, 2360–2369 (2005).
Meyer, R., May, F., Müller, C., Geel, K. & Bernstone, C. Regional search, selection and geological characterization of a large anticlinal structure, as a candidate site for CO2-storage in northern Germany. Environ. Geol. 54, 1607–1618, doi:10.1007/s00254-007-0939-8 (2008).
Li, Q., Liu, G., Liu, X. & Li, X. Application of a health, safety, and environmental screening and ranking framework to the Shenhua CCS project. Int. J. Greenhouse Gas Control 17, 504–514, doi:10.1016/j.ijggc.2013.06.005 (2013).
Grataloup, S. et al. A site selection methodology for CO2 underground storage in deep saline aquifers: Case of the Paris basin. Energy Proc. 1, 2929–2936, doi:10.1016/j.egypro.2009.02.068 (2009).
Bonijoly, D. et al. METSTOR: A GIS to look for potential CO2 storage zones in France. Energy Proc. 1, 2809–2816, doi:10.1016/j.egypro.2009.02.053 (2009).
Hsu, C.-W., Chen, L.-T., Hu, A. H. & Chang, Y.-M. Site selection for carbon dioxide geological storage using analytic network process. Sep. Purif. Technol. 94, 146–153, doi:10.1016/j.seppur.2011.08.019 (2012).
Raza, A. et al. A screening criterion for selection of suitable CO2 storage sites. J. Natural Gas Sci. Eng. 28, 317–327, doi:10.1016/j.jngse.2015.11.053 (2016).
Wei, N. et al. A preliminary sub-basin scale evaluation framework of site suitability for onshore aquifer-based CO2 storage in China. Int. J. Greenhouse Gas Control 12, 231–246, doi:10.1016/j.ijggc.2012.10.012 (2013).
MEP China. Technical Guideline on Environmental Risk Assessment for Carbon Dioxide Capture, Utilization and Storage (on Trial). (Ministry of Environmental Protection of the People’s Republic of China, 2016).
MEP China. Technical Guideline for Ecological Protection Red Line Delineation ( No. 56) (Ministry of Environmental Protection of the People’s Republic of China, 2015).
Lü, Y., Ma, Z., Zhang, L., Fu, B. & Gao, G. Redlines for the greening of China. Environ. Sci. Policy 33, 346–353, doi:10.1016/j.envsci.2013.05.007 (2013).
Bai, Y. et al. New ecological redline policy (ERP) to secure ecosystem services in China. Land Use Policy 55, 348–351, doi:10.1016/j.landusepol.2015.09.002 (2016).
Zheng, L. et al. On modeling the potential impacts of CO2 sequestration on shallow groundwater: Transport of organics and co-injected H2S by supercritical CO2 to shallow aquifers. Int. J. Greenhouse Gas Control 14, 113–127, doi:10.1016/j.ijggc.2013.01.014 (2013).
Du, S., Zheng, L. & Zhang, W. Assessment of shallow aquifer remediation capacity under different groundwater management conditions in CGS field. Arab. J. Geosci. 9, doi:10.1007/s12517-016-2479-6 (2016).
Eriksson, S., Andersson, A., Strand, K. & Svensson, R. Strategic Environmental Assessment of CO 2 Capture, Transport and Storage – Official Report 142 (Vattenfall Research and Development AB, SE-814 26 Älvkarleby, Sweden, 2006).
China’s carbon dioxide geological storage environmental risk research team. Training materials for China’s environmental risk assessment of carbon dioxide geological storage 112 (Chemical Industry Press, 2017).
Li, Q. et al. Application of China’s CCUS Environmental Risk Assessment Technical Guidelines (Exposure Draft) to the Shenhua CCS Project. Energy Proc. doi:10.1016/j.egypro.2017.03.1567 (2017).
MEP China. Standard for Pollution Control on the Security Landfill Site for Hazardous Wastes (GB 18598-2001/XG1-2013) (Ministry of Environmental Protection of the People’s Republic of China, 2013).
MEP China. Standard for Pollution Control on the Landfill Site of Municipal Solid Waste (GB 16889-2008) (Ministry of Environmental Protection of the People’s Republic of China, 2008).
Su, X., Xu, W. & Du, S. Basin-scale CO2 storage capacity assessment of deep saline aquifers in the Songliao Basin, northeast China. Greenh. Gases 3, 266–280, doi:10.1002/ghg.1354 (2013).
Du, S., Su, X. & Xu, W. Assessment of CO2 geological storage capacity in the oilfields of the Songliao Basin, northeastern China. Geosci. J. 20, 247–257, doi:10.1007/s12303-015-0037-y (2015).
Li, Q. et al. Geomechanical Issues of CO2 Storage for Performance and Risk Management. In The 3rd Symposium of the China-Australia Geological Storage of CO 2 (CAGS) (Changchun, Jinlin, China, 2011).
Wei, N., Li, X., Liu, S., Dahowski, R. T. & Davidson, C. L. Early Opportunities of CO2 Geological Storage Deployment in Coal Chemical Industry in China. Energy Proc. 63, 7307–7314, doi:10.1016/j.egypro.2014.11.767 (2014).
Li, X. C. et al. Early opportunities of carbon capture and storage in China. Energy Proc. 4, 6029–6036, doi:10.1016/j.egypro.2011.02.607 (2011).
Zeng, R. et al. New potential carbon emission reduction enterprises in China: Deep geological storage of CO2 emitted through industrial usage of coal in China. Greenh. Gases 3, 106–115 (2013).
Li, Q., Wei, Y.-N. & Chen, Z.-A. Water-CCUS Nexus: Challenges and Opportunities of China’s Coal Chemical Industry. Clean Technol. Environ. Policy 18, 775–786, doi:10.1007/s10098-015-1049-z (2016).
Li, Q., Wei, Y.-N., Liu, G. & Shi, H. CO2-EWR: A cleaner solution for coal chemical industry in China. J. Clean. Prod. 103, 330–337, doi:10.1016/j.jclepro.2014.09.073 (2015).
The White House. U.S.-China Joint Announcement on Climate Change, https://www.whitehouse.gov/the-press-office/2014/11/11/us-china-joint-announcement-climate-change (2014).
Ma, J. et al. Jingbian CCS Project, China: Second Year of Injection, Measurement, Monitoring and Verification. Energy Proc. 63, 2921–2938, doi:10.1016/j.egypro.2014.11.315 (2014).
Shaanxi Yanchang Petroleum (Group) Co. Ltd. CCS: A China Perspective Yanchang Petroleum Report 1: Capturing CO 2 from Coal to Chemical Process. 43 (Global CCS Institute, Melbourne, Australia, 2015).
Yang, Y., Ma, J. & Li, L. Research Progress of 4D Multicomponent Seismic Monitoring Technique in Carbon Capture and Storage. Adv. Earth Sciences 30, 1119–1126, doi:10.11867/j.issn.1001-8166.2015.10.1119 (2015).
EPHC. Environmental Guidelines for Carbon Dioxide Capture and Geological Storage - 2009 (Environment Protection and Heritage Council (EPHC), Australia, 2009).
European Commission. Directive 2009/31/EC of the European Parliament and of the Council of 23 April 2009 on the geological storage of carbon dioxide and amending Council Directive 85/337/EEC, European Parliament and Council Directives 2000/60/EC, 2001/80/EC, 2004/35/EC, 2006/12/EC, 2008/1/EC and Regulation (EC) No 1013/2006. Official Journal of the European Union L140, 114–135 (2009).
US EPA. Federal Requirements Under the Underground Injection Control (UIC) Program for Carbon Dioxide (CO 2) (Environmental Protection Agency, Washington DC, 2015).
MEP China. Quanguo Ziran Baohuqu Minglu (National Nature Reserve List) (China Environmental Science Press, 2014).
State Forestry Administration. National forest park (State Forestry Administration, Beijing, 2014).
State Council. National main function zoning (The People’s Republic of China, Beijing, 2010).
MEP China. National ecological function zoning (Ministry of Environmental Protection of the People’s Republic of China, 2015).
The research was funded by the project entitled An Emission-Transport-Exposure Model Based Study on the Evaluation of the Environmental Impact of Carbon Market (No. 71673107) supported by the National Natural Science Foundation of China, China-Australia Geological Storage of CO2 (CAGS) Project funded by the Australian Government, and China CDM Fund on Update of China’s CCS Technical Roadmap (2013085).
The authors declare that they have no competing interests.
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Cai, B., Li, Q., Liu, G. et al. Environmental concern-based site screening of carbon dioxide geological storage in China. Sci Rep 7, 7598 (2017). https://doi.org/10.1038/s41598-017-07881-7
International Journal of Environmental Science and Technology (2021)
Scientific Reports (2018)