Monitoring the effects of daily activities on the physiological responses of the body calls for wearable devices that can simultaneously track metabolic and haemodynamic parameters. Here we describe a non-invasive skin-worn device for the simultaneous monitoring of blood pressure and heart rate via ultrasonic transducers and of multiple biomarkers via electrochemical sensors. We optimized the integrated device so that it provides mechanical resiliency and flexibility while conforming to curved skin surfaces, and to ensure reliable sensing of glucose in interstitial fluid and of lactate, caffeine and alcohol in sweat, without crosstalk between the individual sensors. In human volunteers, the device captured physiological effects of food intake and exercise, in particular the production of glucose after food digestion, the consumption of glucose via glycolysis, and increases in blood pressure and heart rate compensating for oxygen depletion and lactate generation. Continuous and simultaneous acoustic and electrochemical sensing via integrated wearable devices should enrich the understanding of the body’s response to daily activities, and could facilitate the early prediction of abnormal physiological changes.
Intertwined with concepts of telehealth, the internet of medical things, and precision medicine, wearable sensors offer features to actively and remotely monitor physiological parameters. Wearable sensors can generate data continuously without causing any discomfort1,2 or interruptions to daily activity, thus enhancing the self-monitoring compliance of the wearer and improving the quality of patient care2,3,4. Monitoring of single physical parameters, such as the electrocardiogram5,6,7 and blood pressure (BP)8,9,10, as well as biochemical parameters, such as glucose11,12,13,14,15, using non-invasive wearable sensors has been reported. The importance of integrating multiple sensors on a single device has been demonstrated16, where multiple chemical sensors were integrated into a single wrist band. Following this pioneering work, sensor integration is now shifting towards the combination of different sensor modalities. Recent efforts have led to the integration of physical and chemical sensors into a single wearable device—such as combining electrocardiography electrodes with lactate17,18 or glucose19 sensors to monitor the cardiovascular performance, metabolism, electrolyte balance, or the body temperature of an athlete12,16. However, to the best of our knowledge, the in-depth study of the correlation of cardiovascular parameters, particularly BP, with biomarker levels using an integrated hybrid wearable sensor remains unexplored.
Heart rate (HR) and BP, two of the most important vital signs, can dynamically and directly reflect the physiological status of the body. These cardiovascular parameters can be affected by fluctuations of various biomarker concentrations originating from activities such as movement, stress or the intake of food, drinks and drugs that can lead to sudden and sometimes lethal alterations. Parallel BP–chemical sensing could thus have clinical value, especially for people with underlying health conditions—such as the elderly or individuals who are obese, or those affected by diabetes and cardiovascular diseases—as their physiological response to normal day-to-day activities might differ from healthy individuals. Furthermore, the prevention, diagnosis and treatment of many diseases can benefit greatly from simultaneous monitoring of cardiovascular parameters and biomarker levels. These include acute and deadly septic shock, which commonly involves a sudden drop in BP accompanied by rapidly increasing blood-lactate levels20, and hypoglycaemia- or hyperglycaemia-induced hypotension or hypertension, which increase the risk of stroke, cardiac diseases, retinopathy and nephropathy in patients with diabetes21,22,23,24. Tracking of metabolites and haemodynamic parameters using the same device can increase the self-monitoring compliance of a patient, as it simplifies the complex process of using multiple devices for measuring these parameters, thereby circumstantially preventing dangerous cardiac events and saving lives. The combination of transdisciplinary sensing modalities into a single miniaturized skin-conformal wearable device can yield additional advantages. For example, critically ill and premature infants need continuous monitoring of various dangerous conditions, ranging from hypoglycaemia and sepsis-like infection to open-heart surgery, where BP and the level of lactate or glucose need to be monitored continuously25,26. The neonate-monitoring systems available at present require the application of multiple, often invasive, sensors coupled to bulky instruments on their tiny bodies that pose severe injury risks and barriers to parent–baby bonding27. By integrating different sensing modalities on a single flexible, skin-worn tattoo-like patch, vulnerable patients—from neonates to the elderly—can leverage their monitoring device with minimal discomfort or obtrusiveness. The recent global pandemic has also highlighted the urgent need for remote self-monitoring devices, with particular attention to the management of high BP and diabetes, which are major factors in the death of patients with coronavirus disease 2019 (ref. 28). A comprehensive cardiovascular/biomarker self-monitoring system would enhance the self-awareness of users to their health conditions and alert them as well as their caregivers to the occurrence of abnormal physiological changes.
Here we present a conformal, stretchable and integrated wearable sensor that can monitor BP, HR and the levels of glucose, lactate, caffeine and alcohol towards dynamic and comprehensive health self-monitoring. We use ultrasonic transducers to monitor BP and HR, and electrochemical sensors to measure the levels of biomarkers. Through strategic material selection, layout design and fabrication engineering, we integrated rigid and soft sensor components, namely customized piezoelectric lead zirconate titanate (PZT) ultrasound transducers and printed polymer composites via an innovative solvent-soldering process into a single wearable conformal sensor with high mechanical resiliency and an absence of sensor crosstalk. Such rational design overcomes engineering challenges related to the integration of different sensing modalities and materials to allow real-time monitoring of cardiovascular parameters and biomarker levels in connection to parallel sampling of the interstitial fluid (ISF) and sweat biofluids. The resulting epidermal hybrid device can emit ultrasonic pulses and sense echoes from arteries while stimulating sweat and extracting ISF through iontophoresis (IP), thereby allowing parallel measurements of BP and HR along with multiple biomarkers in these biofluids. We carried out on-body trials on several human volunteers undergoing various activities and stimuli (exercise and the intake of alcohol, food and caffeine; Fig. 1d). The correlations between metabolic variations and haemodynamic activities under these stimuli were monitored and evaluated. The improved sensor assembly process, leveraging the styrene-ethylene-butylene-styrene block copolymer (SEBS)-based stretchable materials, allowed a fast and reliable fabrication of the stretchable and conformal epidermal sensor for acoustic and electrochemical sensing. Such a device offers comprehensive tracking of the effect of daily activities and stimuli on the physiological status of the user, and enables the collection of previously unavailable data towards understanding the body response to such stimuli while addressing the critical post-pandemic needs for remote telemetric patient monitoring.
The multimodal sensing wearable patch is depicted in Fig. 1a. SEBS was used as the stretchable and conformal substrate to support the electrodes and connections printed with customized inks (Fig. 1e and Supplementary Fig. 1). The stretchable substrate and inks allow the high conformity, flexibility (Fig. 1f(i)) and stretchability (Fig. 1f(ii)) required for wearable devices. The BP sensor consists of an array of eight piezoelectric transducers that are aligned with the carotid artery on application to the neck to obtain optimal ultrasonic signals (Supplementary Figs. 2–4). During sensing, the piezoelectric transducers were activated with electrical pulses, transmitting ultrasound beams to the artery, and the time of flight of the echoes from the anterior and the posterior walls of the artery was analysed to gauge the dilation and contraction of the arteries (Fig. 1c,h). The optimal BP signal can be selected from the eight transducers with the best alignment to the artery and hence the highest signal quality, thus ensuring reliable BP sensing during movement, when the patch may undergo some displacement (Supplementary Fig. 11). Detailed information regarding the fabrication of the sensor is discussed in Fig. 2m and Supplementary Note 1. The characterization of the BP sensor is discussed in Supplementary Note 3 and Supplementary Fig. 10. Chemical sensing was realized through non-invasive sweat stimulation (via transdermal pilocarpine delivery) at the IP anode, along with ISF extraction at the IP cathode. Lactate, alcohol and caffeine were monitored only in sweat, whereas glucose was monitored only in the ISF. Detailed information regarding the monitoring of the ISF and sweat analytes via IP is presented in Supplementary Note 4 (Fig. 1b). Chronoamperometry (CA) was used for the electrochemical detection of the hydrogen peroxide product of the glucose oxidase, lactate oxidase and alcohol oxidase enzymatic reactions, whereas differential pulse voltammetry (DPV) was used for the detection of caffeine. The detailed electrode modifications and reaction mechanisms are discussed in Supplementary Fig. 5. The analytical performance of each chemical sensor is shown in Fig. 1g, Supplementary Figs. 6–9 and Supplementary Note 2.
Results and discussion
The performance of the integrated sensor for multiplexed sensing requires reliable data generation from the individual sensors, with no crosstalk between the two sensing modalities. Here, signal crosstalk between the acoustic and electrochemical transducers was prevented by spatially separating both components and using solid-state ultrasound and sensing hydrogel layers (Supplementary Figs. 26 and 27). The device was designed with an optimal distance between the individual detection compartments to ensure successful acoustic BP and HR sensing, IP extraction and electrochemical monitoring. The signal generation of the acoustic sensor relies on high-voltage and high-frequency pulses that may induce signal drift in the chemical sensors, whereas the IP extraction, potentiostatic sensing and potential-sweep sensing may also induce noise in the acoustic signals. As shown in Fig. 2a,d, the BP transducers were located 1 cm away from the chemical sensors, a distance that was determined to be optimal by assessing the crosstalk between the neighbouring sensors (Supplementary Fig. 26).
Such crosstalk effects between the electrochemical and BP sensors were evaluated by recording the corresponding signals during on-body operations. The BP signals were acquired while the potentiostatic electrochemical input was repeatedly switched on and off to assess the effect of the electrochemical sensing of the anodic (Fig. 2e and Supplementary Fig. 24) and cathodic (Fig. 2b) sensors on the BP signal. Similarly, the effect of the acoustic sensing on both sides of the electrochemical sensing was examined by recording the amperometric response while switching the acoustic pulses on and off every 30 s (Fig. 2c,f). Note that without optimization, the electrochemical detection was subject to strong signal interference due to the potential drift caused by the biased voltage from the acoustic pulses (Supplementary Figs. 25 and 26).
Mechanical stability is another crucial factor that dictates the reliability of skin-worn sensors when tensile deformations are expected. The impedance of the chemical sensors and the contact resistance to the PZT transducers may vary with the strain applied to the soft conformal device, thereby leading to changes in the measured signals, which affect the reliability of the device. Stability of the PZT contact following mechanical stress was realized by developing a solvent-soldering process based on the fast dissolution and room-temperature curing of SEBS-based materials. During the assembly process, the PZT transducers can be quickly mounted and bonded onto the SEBS substrate and connected to the SEBS-based stretchable silver ink by wetting the electrode surface with toluene (Fig. 2m). The solvent-soldered PZT chips can thus be securely bonded to the printed electrodes without delamination during stretching deformations (Fig. 2n), with substantially improved assembly efficiency in comparison to previous reports10. The effects of stretching on the sensing performance were assessed by stretching tests at a uni-axial strain of 20%. The device was stretched repeatedly in vertical (Fig. 2g) and horizontal (Fig. 2j) directions. The ultrasonic echo signals, against a two-layered Ecoflex, and the current (CA signal) from the bare Prussian-blue electrode (held at −0.2 V), in buffer solution, were recorded after every 200 cycles of stretching at 20% strain. As shown in Fig. 2h,k, although the intensity of the acoustic transducer signal decreased slightly with stretching, the temporal relationship between each peak that corresponded to two echoes did not change; hence, the deformations did not affect the recorded waveform. Similarly, the electrochemical sensors did not show noticeable current change as the stretching cycle progressed (Fig. 2i,l and Supplementary Figs. 12, 13). The device also demonstrated good mechanical resilience after it was transferred to the body. Twisting and bending of the sensor on the skin is shown in Fig. 2o–q. Mechanical-resilience tests were also performed during active 20% stretching deformation. The bare and enzyme-modified electrochemical sensors were evaluated in vitro while stretched in two directions (horizontal and vertical), and the BP device was evaluated while capturing the BP signal when turning the neck 90° to the side; the glucose response did not change during or after 100 stretching cycles, and no changes were observed in the BP waveform while turning the neck (Supplementary Figs. 15–17). Scanning electron microscopy images depicting the structural changes of the surfaces of the printed stretchable silver and carbon traces are in Supplementary Fig. 14, demonstrating that the printed composites are unaffected by the mechanical deformation. A discussion of these images is presented in Supplementary Note 5.
Tracking cardiovascular activities and biomarker levels
The monitoring of both dynamic cardiovascular parameters and biomarker concentrations by the device allows evaluating the effects of common daily activities on the physiological status of an individual and continuously collecting data about their response to these everyday activities. The levels of lactate, glucose, alcohol and caffeine in the body can fluctuate due to common daily activities; furthermore, the impact of these levels on BP also varies based on the physical conditions of the individual. The parallel measurement of biomarkers and BP allows collecting the responses of an individual to such daily activities. The ability of the device to track multiple biomarkers while capturing cardiac parameters can further help deconvolute the additive effects of multiple stimuli on physiological parameters, which has great implications for self-monitoring in personalized health management. To study the effects of each activity on the cardiac parameters, measurements were performed before and after the stimulus. Tests were performed by monitoring BP along with key sweat and ISF biomarkers, corresponding to specific medical situations. More complex patch designs (illustrated in Supplementary Figs. 34 and 35) can be used for the simultaneous monitoring of BP and multiple sweat chemical markers.
Exercise, comprising any action that demands physical effort, has a major impact on the physiological response of the body, including changes in the HR, BP and levels of lactate. During prolonged exercise, the levels of lactate in the blood and sweat increase due to metabolic stress29, the HR is raised to meet the muscle demand for oxygen and the BP surges due to increased availability of vasodilatory mediators such as nitric oxide30. To study these effects, several volunteers were asked to perform stationary cycling at a fixed level for 30 min, followed by 5 min of rest. The artery displacement during cycling was within the device coverage (Supplementary Video 2). The BP was recorded while sweating was stimulated before and after the exercise for the lactate measurements, and the obtained BP and lactate-level data were validated using a commercial cuff-style BP monitor and a blood-lactate meter. As expected, large changes in the BP and HR readings were observed after exercise, increasing to 150 mm Hg and 98 beats per minute (b.p.m.), respectively (Fig. 3a(i),(ii)). The levels of lactate in sweat also increased, with low lactate levels recorded at the beginning, which increased twofold after the exercise (Fig. 3a(iv),(v)). The BP and sweat-lactate data collected from the device agreed well with the validation methods, as shown in Fig. 3a(iii)–(vi). Note that as no exogenous drugs were used to affect the BP of the volunteers, the relaxation and contraction of the elastine- and collagen-rich central arteries due to exercise could be considered negligible and no additional recalibration of the acoustic sensor was thus needed during the experiment.
As another commonly seen unhealthy stimulus, excessive alcohol consumption has been shown to increase cardiovascular risks via alcohol-induced hypotension and hypertension31,32. Alcohol may have different effects on BP, depending on the amount and frequency of its consumption as well as genetic factors related to resistance or sensitivity to alcohol33,34. Variations in BP following alcohol ingestion are related to direct vasodilation, surge in cortisol secretion and reduced insulin sensitivity35. For the sensor experiments focusing on alcohol as the stimulus, the BP and sweat-alcohol levels were measured before and 20 min after drinking 200 ml of an alcoholic beverage (19% vol; Fig. 3b). A commercial alcohol breathalyser was used for correlation with the blood-alcohol level. As shown in Fig. 3b, alcohol consumption resulted in an increase in the HR (from 69 to 85 b.p.m.) and BP (from 120 to 136 mm Hg) of the volunteer (Fig. 3b(i),(ii)). These results are in agreement with studies showing that intake of a single alcoholic beverage by non-heavy drinkers can lead to a temporary BP spike35. Note that for heavy drinkers, there might be a considerable BP morning surge that greatly increases the risk of stroke35. Concurrently, the sensor allows the reliable detection of sweat alcohol, as this small polar molecule can be found in sweat with a 1:1 correlation to blood (Fig. 3b(iv),(v))36.
Metabolites such as glucose can also affect the BP waveform by changing the viscosity of blood. Blood viscosity increases under conditions of insulin resistance, altering the flux of blood in the capillaries and hence the shape of the BP pulse37,38. Studies have shown that individuals with a high BP are prone to higher levels of blood glucose39. To test the effect of the increase in glucose on the BP, healthy individuals without diabetes were asked to consume a sugar-rich meal after fasting. The BP and levels of ISF glucose were recorded using the device before and 15 min after food consumption, with the glucose level validated using a commercial glucometer at both times. As shown in Fig. 3c(i),(ii), the food-consumption experiment resulted in negligible changes in the BP and HR, as detected by the sensor. In contrast, the electrochemical biosensor readily detected changes in the levels of ISF glucose after the meal consumption (Fig. 3c(iv),(v)). These data are within the expectation for individuals without diabetes, as glucose-induced BP changes occur only when glucose levels increase to alter the blood pumping through the arteries, which is uncommon for individuals without diabetes, whose glucose is readily regulated by the responsive release of insulin.
Finally, caffeine was chosen as another chemical stimulus commonly used in our daily lives. Caffeine intake is known to lead to an increase in BP through the inhibition of the adenosine receptor and release of stress hormones, such as norepinephrine or cortisol40. These biochemical changes can result in transient contractions of the arterial smooth muscle and influence the vascular tone by phosphodiesterase inhibition41. The effect of caffeine on BP varies and has been shown to be more pronounced in individuals with hypertension40,41. The epidermal BP and caffeine sensor patch was evaluated on individuals with and without caffeine-intake habits, and their BP and sweat-caffeine levels were measured before and 30 min after the consumption of a caffeine-rich (80 mg) sugar-free energy drink. The amount of caffeine in sweat was validated through a standard addition voltammetric method, spiking caffeine in a collected sweat sample (Supplementary Fig. 19). As illustrated in Supplementary Fig. 29b, the on-body tests on an individual with habitual caffeine intake showed no notable changes in the BP and HR after the consumption of high caffeine doses, reflecting the caffeine tolerance and healthy BP levels of the volunteer. In contrast, BP variation was more pronounced for the individual with no habitual caffeine intake (Fig. 3d). The caffeine sensor displayed a flat DPV baseline response before the caffeine intake, whereas the sweat DPV recorded 30 min after the caffeine intake showed a distinct anodic peak current at 1.2 V, corresponding to the caffeine oxidation (Fig. 3d(iv),(v))42,43. The current levels before and after the caffeine intake were compared with the results obtained through the standard addition method for caffeine, demonstrating a good correlation between both parameters (Fig. 3d(vi)). Note that the in vitro electrochemical characterization of the caffeine sensor in pH 4.5 showed current peaks around 1.1 V (Supplementary Fig. 9). This small potential shift reflects the use of acetate-buffer-loaded agarose gel over the caffeine sensor to minimize the effect of fluctuations in the sweat pH (that is, pH 4.5–7.0).
Device monitoring multiple stimuli
We then evaluated the device in real-life scenarios, where people usually experience multiple activities that may have synergistic or counteracting effects on the physiological responses of the body. The device was evaluated for use in monitoring cardiovascular parameters along with multiple biomarker levels on individuals exposed to multiple stimuli. A common example of a counteracting effect on glucose levels is exercising along with food intake, as glucose can be quickly consumed during exercise to produce energy44. Exercise is also expected to increase the BP and lactate levels in an individual, as was shown in previous single-stimuli tests. To study this scenario, the volunteer was asked to consume a sugar-rich meal and then exercise on a stationary bike for 30 min, and the ISF glucose, sweat lactate and BP were monitored before and after each step. As shown in Fig. 4a, normal systolic BP, high glucose (>100 mg dl−1) and low lactate levels were observed before the cycling activity. After the exercise, the glucose levels decreased, accompanied by a considerable increase in the BP, HR and level of lactate, as predicted from previous tests. Control experiments—performed without any food or exercise—were used to corroborate that the change in signal resulted solely from the increase in the lactate and glucose levels (Supplementary Fig. 32). These findings are in agreement with a previously reported extensive study of a similar wearable electrochemical system15. Figure 4a illustrates that the sensor is able to capture the complex processes resulting from the simultaneous food and exercise stimuli, including the digestion of food to produce glucose as the energy reservoir, the glycolysis reaction consuming the glucose and oxygen to release energy, the increased BP and HR compensating for the oxygen depletion and the lactate generation during the hypoxic condition in exercise.
The influence of the combined intake of alcohol and glucose on BP and HR, simulating a typical scenario of alcohol consumption during meals, was also studied in volunteering individuals. Based on previous observations, increased glucose levels are not expected to cause large changes to the BP of the individuals, whereas an increase in BP is expected after the alcohol intake. Therefore, an additive effect is expected on the glucose levels and BP when combining the intake of alcohol and sugary food. Moreover, the digestion of alcoholic drinks, along with the reduced insulin sensitivity caused by alcohol consumption, can further aggravate the increase in glucose levels and BP15. On the other hand, excessive alcohol intake can lead to severe hypoglycaemia and hypotension, even when combined with glucose intake, particularly for insulin-dependent individuals with diabetes45. Therefore, parallel monitoring of glucose and BP is important to distinguish between cases of moderate or excessive drinking and prevent drinking-induced accidents, especially for individuals with underlying health conditions46,47. Sweat-alcohol, ISF-glucose and BP signals were recorded in the fasting state, after alcohol consumption and after food intake. As shown in Fig. 4b(iv)–(vi), before any consumption of food or alcohol, the blood-glucose and -alcohol readings were typical of a non-diabetic fasting-state reading—that is, 90 mg dl−1 glucose and a blood alcohol concentration of 0%—whereas increased BP, glucose and alcohol signals were observed for 20 min after the stimuli. The observed increase in BP following alcohol intake alone was 16 mm Hg (Fig. 3b(iii)), rising further to 20 mm Hg after the concurrent intake of sugary food (Fig. 4b(iii)). Such BP variations demonstrate the synergetic effect of the combining alcohol and glucose intake on the BP. Smaller changes in HR were observed following the alcohol and food intake compared with alcohol intake alone, indicating that different mechanisms were responsible for the increase in BP. Control experiments, carried out without the intake of food or drink, were used to corroborate that the observed signal changes were solely due to the increase in alcohol and glucose (Supplementary Fig. 33), as supported by early findings15.
Continuous BP and biomarker monitoring
The ability of the sensor to capture the dynamic biomarker and BP fluctuations during physical activity was also demonstrated. Physically active individuals are expected to have a lower resting BP, considerably reducing the risk of heart-failure events48,49. The lower resting BP can further be reflected in a smaller increase in BP during exercise, as physically active individuals signal the body earlier to release nitric oxide to promote enhanced vasodilation48. Smaller increases in lactate levels are also expected for active individuals compared with those who are not active50. The BP of an individual is expected to decrease following intense exercise activity, eventually returning to its original value, regardless of fitness level51. Furthermore, studies have demonstrated a close relationship between the magnitude of the post-exercise decrease in BP and the lactate levels, showing that elevated blood-lactate levels after high-intensity exercise promote larger differences between the pre- and post-exercise BP values52. Thus, such complex dynamic processes require the hybrid sensor to operate continuously to capture these real-time fluctuations throughout the activity. Individuals with different fitness levels (physically active and inactive) were asked to perform a 30-min cycling activity at constant intensity while wearing the device (during the whole experiment), and their BP and sweat-lactate levels were monitored continuously until the exercise was stopped. As sweat was generated spontaneously from the activity, IP was not used for this portion of the study. Validation data were also recorded before, 10 min into and after the exercise. As shown in Fig. 5a (for the physically active individual) and Fig. 5b (for the sedentary individual), considerably higher sweat-lactate levels and increased BP values were observed during the exercise for the sedentary individual compared with the active individual. Higher HR, BP and sweat-lactate levels are expected during exercise for inactive individuals due to the elevated catecholamine levels compared with physically active individuals, thereby leading to differences in BP depending on the fitness levels and cardiovascular system53. To address the potential effect of sweat electrolytes on the activity of the Prussian-blue transducer54, we used an applied potential that was sufficiently negative (−0.2 V) to accommodate small possible shifts in the Prussian-blue peak potential (Supplementary Fig. 38). We also demonstrated a patch design capable of performing parallel potentiometric measurements of the sweat-electrolyte levels to correct for the electrolyte effect (Supplementary Fig. 35). The on-body data are shown in Supplementary Fig. 39.
We have shown a conformal skin-worn device capable of parallel monitoring of BP, HR and multiple biomarkers. This has been realized by addressing major engineering challenges in the integration of rigid ultrasound transducers and soft and stretchable electrochemical sensors into a single flexible and stretchable device while ensuring mechanical performance and avoiding signal crosstalk. The SEBS-based solvent-soldering process has substantially simplified the assembly of a sensor with complex structures, while ensuring reliable mechanical behaviour and continuous epidermal BP- and biomarker-signal recordings under different chemical and physical stimuli and activities. Signal crosstalk between the acoustic and electrochemical transducers was prevented by spatially separating both components and using solid-state sensing hydrogel layers. Repeated mechanical deformation tests demonstrated outstanding durability and reliability of the electrochemical and acoustic sensors.
Such acoustic and electrochemical sensing offers continuous monitoring of the physiological status of the user and its response to multiple everyday activities and stimuli. This multimodal wearable technology has thus been shown to be useful for correlating common daily activities—such as, exercise, drinking and eating—with changes in BP, HR and biomarker levels. These encouraging results support the possibility of developing hybrid wearable sensors with complex integration of chemical and physical sensors on a single conformal wearable patch for the simultaneous monitoring of multiple relevant parameters. Such integration of reliable and comprehensive epidermal sensors can only be realized with judicious selection of materials, optimized structural engineering and a high-throughput fabrication process in mind. Although the integrated device displays attractive features, there are still opportunities for the following improvements to the measurements of BP, HR and metabolites. (i) The integrated patch relies on the IP pilocarpine stimulation of sweat, which limits the operational use due to the depletion of pilocarpine. Long-term sweat-stimulating drugs (for example, carbachol) could be used to extend the operation period and perform multiple measurements using a single sweat-stimulation step. (ii) Testing of multiplexed patch designs to allow for comprehensive multi-analyte monitoring (Supplementary Fig. 34). (iii) Incorporation of a perspiration-rate sensing interface to normalize the ISF marker readings or use of sweat-suppressive drugs along with an internal standard (sodium) to address potential ISF dilution by passive sweating. (iv) Conducting extensive validations involving a large number of individuals with various health conditions, including patients with diabetes and cardiovascular disease. (v) Full miniaturization of the device through the development of electronics with integrated ultrasound and multi-potentiostatic capabilities, along with signal processing and wireless transmission functionalities. Previous examples have shown the successful miniaturization of wearable devices featuring multiplexed sensing modalities, wireless communications and displays16,55,56. The future development of a stand-alone acoustic sensing interface circuit, coupled with artificial intelligence-aided signal processing, will fully transform the present device into a comprehensive skin-worn sensing system. By addressing these opportunities and adding more sensing parameters, we envision a fully integrated multiplexed wearable health-monitoring device that offers insights into the health and physiological status of individuals in the prevention and management of chronic diseases. This device represents a first step towards multimodal wearable sensors that fuse acoustic and electrochemical sensors for more comprehensive monitoring of human physiology and towards telehealth transformation. It thus paves the way into a family of skin-conformal tools capable of providing high-quality and high-density information regarding the status of human health and lays the foundation for next-generation wearable patches capable of hybrid chemical–electrophysiological–physical monitoring.
Materials and reagents
Chitosan, acetic acid, bovine serum albumin, l-lactic acid, NaH2PO4, Na2HPO4, d+-glucose, glucose oxidase from Aspergillus niger type X-S (EC 220.127.116.11), Nafion, agarose, pilocarpine nitrate, Prussian blue (soluble), toluene, ethanol and silver flakes were obtained from Sigma-Aldrich. Graphite powder was purchased from Acros Organics. Lactate oxidase (activity of 101 U mg−1) was purchased from Toyobo Corp. SEBS (G1645) was received from Kraton Corporation, whereas Ecoflex 00–30 was purchased from Smooth-on Inc. Super-P carbon black was obtained from MTI Corporation. The ultrasound gel pad (AQUAFLEX) was purchased from Parker Laboratories Inc. All reagents were used without further purification.
Sensor fabrication, assembly and electrode modification
The screen-printing was carried out using a semi-automatic MPM-SPM printer (Speedline Technologies) and custom stainless steel stencils developed using AutoCAD software (Autodesk) and produced by Metal Etch Services, with the dimensions 30.48 cm × 30.48 cm and a thickness of 125 µm. The electrodes were printed layer-by-layer as illustrated in Supplementary Fig. 1. Bulk PZT was used for the ultrasound transducers, which were diced (Disco Automatic Dicing Saw DAD3220) into rectangular-shaped pixels (0.8 mm × 3 mm) and sandwiched by two layers of stretchable silver inks as electrodes. The connection between the transducers and the silver traces was realized by adding a toluene droplet to the printed silver traces and placing the transducers on the softened ink. After attaching the PZT transducers, the screen-printed ground connection was placed on the sensor by dissolving the printed traces in a similar fashion. Details of the transducer assembling process are illustrated in Supplementary Fig. 2. The biosensor electrodes were subsequently modified by drop casting the respective enzymes and polymer layers. Details of the ink formulation, printing and assembling processes, and the individual drop-casting protocols for different biosensors are provided in Supplementary Note 1.
Sensor in vitro calibration
The fabricated sensors—that is, the lactate, glucose, alcohol and caffeine biosensors—and the PZT acoustic sensors were calibrated separately in in vitro settings. The biosensors were calibrated using 0.1 M PBS (pH 7.4) or 0.01 M acetate buffer (pH 4.5) with successive spiking of the corresponding analytes and recording of the corresponding CA (for lactate, glucose and alcohol) and DPV (for caffeine). Protocols of the in vitro biosensor calibrations are discussed in detail in Supplementary Note 2. The calibration of the BP waveform is discussed in Supplementary Note 3.
Sensor mechanical tests
The mechanical testing was conducted via controlled stretching tests. A programmable motorized linear stage (X-LRQ, Zaber Technologies Inc.) was used to stretch the device with controlled strain and speed. One of the edges of the printed device was taped at the fixed end of the stage and the other to the moving end of the stage. The device was first stretched to 120% of its original length in the horizontal direction at a speed of 3 mm s−1 and then released back to its original size at the same speed. This process was programmed to be repeated 200 times so that the device could be taken from the stage for measurements before remounting for subsequent stretching. The process was repeated until 1,000 cycles of stretching were completed (Supplementary Figs. 12 and 13). This process was repeated for deformations in the vertical direction using the same device. Electrochemical tests under constant deformation of 120% stretching (horizontal and vertical directions) were conducted after every 200 stretching cycles until 1,000 stretching deformations had been performed (Supplementary Figs. 15 and 16). The resiliency of the sensor was visually inspected by attaching the device to the skin and subjecting it to various deformations (Fig. 2); the corresponding printed surfaces were also characterized via scanning electron microscopy imaging before and after repeated stretching (FEI Quanta 250), as shown in Supplementary Fig. 14.
Sensor crosstalk tests
The crosstalk between the acoustic and electrochemical signals was analysed on-body by monitoring the changes in one signal while the other signal was generated intermittently. For analysing the co-sensor interference from the CA electrochemical measurement to the BP waveform, the BP signals were recorded continuously for at least 4 s in two stages: when the CA was already being performed by applying a potential of −0.2 V to the electrochemical sensors and when the detection potential was turned on after the BP recording had already started. The interference tests from the BP sensor on the CA measurements were performed in the same fashion for the anodic and cathodic sensors as follows: for analysing the crosstalk effect of the acoustic signal generation following the acquisition of the electrochemical signal, the CA signal was recorded continuously for 180 s while the electric pulses for the BP measurements were delivered to the PZT transducer in an off-on-off-on pattern with a period of 30 s for each phase. The crosstalk from the DPV and the acoustic signal was evaluated in the same fashion as for the CA tests as follows. The effect of the acoustic signal on the caffeine sensor was evaluated in two stages: first, by recording the DPV signal while the BP recording was being applied, followed by terminating the BP signal when the DPV reached the peak potential and by recording the DPV signal before initiating the BP acquisition at peak potential. The corresponding data obtained are included in Fig. 2 and Supplementary Fig. 24. All signal generation and data acquisition were performed using a μAutolab III electrochemical analyser (Metrohm) for the chemical sensors and the 5077PR pulser-receiver (Olympus) for the acoustic sensors. The potentiostat was configurated with a ±5 V voltage and 1 mA current limit to avoid overcurrent or overvoltage. The device was visually inspected to ensure that the transducers were fully covered by the SEBS substrates for insulation. No capacitive coupling, short-circuiting or breakdown conduction were observed during the experiment.
Sensor on-body test protocols
Epidermal evaluation of the device was performed on healthy consenting individuals with no previous history of heart conditions, diabetes or chronic pain, and in strict compliance with the protocol approved by the Institutional review board at the University of California, San Diego. The device was placed on the neck of the volunteers for all on-body evaluations. The glucose, lactate, alcohol and BP signals were validated with a commercial glucometer (ACCU-CHEK), blood-lactate meter (NOVA Biomedical), breathalyser (BACtrack S80 Pro) and FDA-approved BP cuff (LOVIA), respectively, before every set of measurements using the integrated sensor. Caffeine concentrations were estimated by standard addition methodology using collected sweat (Supplementary Fig. 19). Sweat stimulation and ISF extraction were realized simultaneously using a μAutolab III electrochemical analyser to apply a current density of 0.3 mA cm−2 between the cathode and anode electrodes for 10 min. A pre-conditioning step was carried out on the skin before sweat generation by applying the same current density using agarose gels in the cathode and anode compartments for 10 min, followed by immediate placement of the device with pilocarpine delivery gel on the conditioned area. Before placing the sensor, the skin was thoroughly cleaned with soap and alcohol wipes. The patch was transferred to the skin using double-sided clean laser tattoo transfer adhesive (Papilio, TM). Openings were made in the adhesive film to expose the sensors and IP electrodes to the skin. For all measurements, a single device was used for each volunteer to perform the ‘before’ and ‘after’ tests. The device was kept on the neck of the volunteer throughout the entire experiment, unless otherwise specified. Details of the hydrogel fabrication and skin transfer processes are illustrated in Supplementary Figs. 21–23 and Supplementary Video 1.
The on-body results were acquired using a benchtop CHI 1230A electrochemical analyser for the biosensors and 5077PR pulser-receiver (Olympus) for the acoustic sensors. Food intake refers to the intake of sugar-rich food (100 g cheesecake; 350 kcal, 22 g sugar). Alcohol intake refers to the intake of alcohol (200 ml wine; alcohol, 19% vol). Caffeine intake refers to the intake of a sugar-free caffeinated drink (248 ml; 80 mg caffeine). Exercise refers to a 30-min exercise session on a stationary bike with constant intensity followed by a 5-min cooling period.
Lactate and BP signals were acquired for three healthy volunteers before and after exercise. The device was removed from their skin during the 30-min exercise on a stationary bike and kept in a wet chamber at room temperature. After the exercise, and following a 5-min cooling period, the neck of the volunteer was cleaned with soap and alcohol pads for replacing the same sensor to the same area. The optimal BP signal after the sensor replacement was selected by testing the PZT array in the BP sensor. The influence of device removal or replacement on the signal was studied, as illustrated in Supplementary Fig. 11.
Alcohol levels and BP were measured before and 20 min after alcohol consumption. The device was kept on the neck of the volunteer during the entire experiment.
Signals for BP and ISF glucose were acquired for three healthy volunteers in the fasting state (16 h) and 15 min after consuming the sugar-rich food. The device was kept on the neck of the volunteer throughout the entire experiment.
The caffeine levels in the sweat of the volunteer were monitored before and 30 min after consuming a sugar-free caffeine drink. The device was kept on the neck of the volunteer throughout the entire experiment. For the on-body tests, an agarose gel loaded with acetate buffer pH 4.5 was used, covering only the caffeine sensor. Stimulated sweat was collected before the caffeine ingestion for the standard addition caffeine determination.
Simultaneous alcohol and food intake
The dual modality of the sensor was tested by combining alcohol and food intake. The BP, ISF-glucose and sweat-alcohol levels were measured before and 20 min after the simultaneous consumption of an alcoholic beverage and the sugar-rich food. The device was kept on the neck of the volunteer throughout the entire experiment.
Food intake and exercise
The dual modality of the sensor was tested for the monitoring of BP as well as the levels of glucose and lactate. The volunteer was first asked to consume a sugar-rich food. Fifteen minutes after the food consumption, ISF glucose, sweat lactate and BP were measured. Next, the device was removed from the volunteer and kept in a wet chamber at room temperature, and the volunteer was asked to perform the physical exercise on a stationary bicycle for 30 min, followed by cooldown for 5 min. After the cooldown interval, the skin was cleaned and the same sensor was used for subsequent measurements of the ISF-glucose, sweat-lactate and BP levels.
Continuous lactate and BP sensing during exercise
The sensor was further tested by monitoring dynamic changes in BP and sweat lactate during continuous physical activity. Individuals with different fitness levels (physically active and inactive) were asked to perform 30 min of cycling activity at constant intensity while wearing the sensor. As sweat was generated spontaneously from the activity, IP and the IP gels were not used for this portion of the study. The BP and blood lactate were measured just before the start of the exercise and the initial sweat-lactate level was measured 5 min after starting the exercise when sweat was first generated. The BP and blood-lactate signals were recorded again within approximately 10 min. The BP and blood-lactate levels were also recorded on completion of the exercise for validation.
Further information on research design is available in the Nature Research Reporting Summary linked to this article.
All the data generated and analysed during the study are included in the paper and its Supplementary Information.
The LabView code used for processing the transducer raw signals into blood-pressure waveforms is available at https://doi.org/10.5281/zenodo.4433220.
Kim, J., Campbell, A. S., de Ávila, B. E.-F. & Wang, J. Wearable biosensors for healthcare monitoring. Nat. Biotechnol. 37, 389–406 (2019).
Yu, Y., Nyein, H. Y. Y., Gao, W. & Javey, A. Flexible electrochemical bioelectronics: the rise of in situ bioanalysis. Adv. Mater. 32, 1902083 (2020).
Khan, Y., Ostfeld, A. E., Lochner, C. M., Pierre, A. & Arias, A. C. Monitoring of vital signs with flexible and wearable medical devices. Adv. Mater. 28, 4373–4395 (2016).
Wang, C., Wang, C., Huang, Z. & Xu, S. Materials and structures toward soft electronics. Adv. Mater. 30, 1801368 (2018).
Lee, S. P. et al. Highly flexible, wearable, and disposable cardiac biosensors for remote and ambulatory monitoring. npj Digit. Med. 1, 2 (2018).
Lee, Y.-D. & Chung, W.-Y. Wireless sensor network based wearable smart shirt for ubiquitous health and activity monitoring. Sens. Actuators B 140, 390–395 (2009).
Yapici, M. K., Alkhidir, T., Samad, Y. A. & Liao, K. Graphene-clad textile electrodes for electrocardiogram monitoring. Sens. Actuators B 221, 1469–1474 (2015).
Luo, N. et al. Flexible piezoresistive sensor patch enabling ultralow power cuffless blood pressure measurement. Adv. Funct. Mater. 26, 1178–1187 (2016).
Dagdeviren, C. et al. Conformable amplified lead zirconate titanate sensors with enhanced piezoelectric response for cutaneous pressure monitoring. Nat. Commun. 5, 4496 (2014).
Wang, C. et al. Monitoring of the central blood pressure waveform via a conformal ultrasonic device. Nat. Biomed. Eng. 2, 687–695 (2018).
Bandodkar, A. J. et al. Tattoo-based noninvasive glucose monitoring: a proof-of-concept study. Anal. Chem. https://doi.org/10.1021/ac504300n (2015).
Lee, H. et al. Wearable/disposable sweat-based glucose monitoring device with multistage transdermal drug delivery module. Sci. Adv. 3, e1601314 (2017).
Kim, J., Campbell, A. S. & Wang, J. Wearable non-invasive epidermal glucose sensors: a review. Talanta 177, 163–170 (2018).
Lee, H., Hong, Y. J., Baik, S., Hyeon, T. & Kim, D. H. Enzyme-based glucose sensor: from invasive to wearable device. Adv. Healthc. Mater. https://doi.org/10.1002/adhm.201701150 (2018).
Kim, J. et al. Simultaneous monitoring of sweat and interstitial fluid using a single wearable biosensor platform. Adv. Sci. https://doi.org/10.1002/advs.201800880 (2018).
Gao, W. et al. Fully integrated wearable sensor arrays for multiplexed in situ perspiration analysis. Nature 529, 509–514 (2016).
Imani, S. et al. A wearable chemical–electrophysiological hybrid biosensing system for real-time health and fitness monitoring. Nat. Commun. 7, 11650 (2016).
Bruno, G., Anastasova, S. & Z. Yang, G. A smart wireless ear-worn device for cardiovascular and sweat parameter monitoring during physical exercise: design and performance results. Sensors 19, 1616 (2019).
Hong, Y. J. et al. Multifunctional wearable system that integrates sweat-based sensing and vital-sign monitoring to estimate pre-/post-exercise glucose levels. Adv. Funct. Mater. 28, 1805754 (2018).
Gomez, H. & Kellum, J. A. Lactate in sepsis. JAMA 313, 194–195 (2015).
Zanella, M. T., Kohlmann, O. & Ribeiro, A. B. Treatment of obesity hypertension and diabetes syndrome. Hypertension https://doi.org/10.1161/01.hyp.38.3.705 (2001).
Cheung, B. M. Y. & Li, C. Diabetes and hypertension: is there a common metabolic pathway? Curr. Atheroscler. Rep. 14, 160–166 (2012).
Epstein, M. & Sowers, J. R. Diabetes mellitus and hypertension. Hypertension 19, 403–418 (1992).
Deedwania, P. Hypertension, dyslipidemia, and insulin resistance in patients with diabetes mellitus or the cardiometabolic syndrome: benefits of vasodilating β-blockers. J. Clin. Hypertens. 13, 52–59 (2011).
Murković, I., Steinberg, M. D. & Murković, B. Sensors in neonatal monitoring: current practice and future trends. Technol. Health Care 11, 399–412 (2003).
Ho, K. K. Y. et al. Evaluation of an anti-thrombotic continuous lactate and blood pressure monitoring catheter in an in vivo piglet model undergoing open-heart surgery with cardiopulmonary bypass. Chemosensors 8, 56 (2020).
Chung, H. U. et al. Binodal, wireless epidermal electronic systems with in-sensor analytics for neonatal intensive care. Science 363, eaau0780 (2019).
Yang, J. et al. Prevalence of comorbidities and its effects in patients infected with SARS-CoV-2: a systematic review and meta-analysis. Int. J. Infect. Dis. 94, 91–95 (2020).
Sakharov, D. A. et al. Relationship between lactate concentrations in active muscle sweat and whole blood. Bull. Exp. Biol. Med. 150, 83–85 (2010).
Halliwill, J. R. Mechanisms and clinical implications of post-exercise hypotension in humans. Exerc. Sport Sci. Rev. 29, 65–70 (2001).
Carter, J. R., Stream, S. F., Durocher, J. J. & Larson, R. A. Influence of acute alcohol ingestion on sympathetic neural responses to orthostatic stress in humans. Am. J. Physiol. Metab. 300, E771–E778 (2011).
Roerecke, M. et al. The effect of a reduction in alcohol consumption on blood pressure: a systematic review and meta-analysis. Lancet Public Health 2, e108–e120 (2017).
Chen, L., Davey Smith, G., Harbord, R. M. & Lewis, S. J. Alcohol intake and blood pressure: a systematic review implementing a Mendelian randomization approach. PLoS Med. 5, e52 (2008).
Maheswaran, R., Gill, J. S., Davies, P. & Beevers, D. G. High blood pressure due to alcohol. A rapidly reversible effect. Hypertension 17, 787–792 (1991).
Ohira, T. et al. Effects of habitual alcohol intake on ambulatory blood pressure, heart rate, and its variability among Japanese men. Hypertension 53, 13–19 (2009).
Hauke, A. et al. Complete validation of a continuous and blood-correlated sweat biosensing device with integrated sweat stimulation. Lab Chip 18, 3750–3759 (2018).
Monte-Moreno, E. Non-invasive estimate of blood glucose and blood pressure from a photoplethysmograph by means of machine learning techniques. Artif. Intell. Med. 53, 127–138 (2011).
Çinar, Y. Blood viscosity and blood pressure: role of temperature and hyperglycemia. Am. J. Hypertens. 14, 433–438 (2001).
Filipovsky, J. et al. The relationship of blood pressure with glucose, insulin, heart rate, free fatty acids and plasma cortisol levels according to degree of obesity in middle-aged men. J. Hypertens. 14, 229–235 (1996).
Mort, J. R. & Kruse, H. R. Timing of blood pressure measurement related to caffeine consumption. Ann. Pharmacother. 42, 105–110 (2008).
Nurminen, M.-L., Niittynen, L., Korpela, R. & Vapaatalo, H. Coffee, caffeine and blood pressure: a critical review. Eur. J. Clin. Nutr. 53, 831–839 (1999).
Tai, L.-C. et al. Methylxanthine drug monitoring with wearable sweat sensors. Adv. Mater. 30, 1707442 (2018).
Ciui, B. et al. Chemical sensing at the robot fingertips: toward automated taste discrimination in food samples. ACS Sens. 3, 2375–2380 (2018).
Asano, R. Y. Acute effects of physical exercise in type 2 diabetes: a review. World J. Diabetes 5, 659–665 (2014).
Klaric, D. & Klaric, V. Alcohol-induced coma, hypothermia and hypotension. J. Membr. Sci. Technol. 5, 1000137 (2015).
Wilson, E. & Waring, W. S. Severe hypotension and hypothermia caused by acute ethanol toxicity. Emerg. Med. J. 24, e7 (2007).
Hillbom, M., Saloheimo, P. & Juvela, S. Alcohol consumption, blood pressure, and the risk of stroke. Curr. Hypertens. Rep. 13, 208–213 (2011).
Nystoriak, M. A. & Bhatnagar, A. Cardiovascular effects and benefits of exercise. Front. Cardiovasc. Med. https://doi.org/10.3389/fcvm.2018.00135 (2018).
Fagard, R. H. Effects of exercise, diet and their combination on blood pressure. J. Hum. Hypertens. 19, S20–S24 (2005).
Jia, W. et al. Epidermal biofuel cells: energy harvesting from human perspiration. Angew. Chem. Int. Ed. 52, 7233–7236 (2013).
MacDonald, J. R. Potential causes, mechanisms, and implications of post exercise hypotension. J. Hum. Hypertens. 16, 225–236 (2002).
Crisafulli, A. et al. Effect of differences in post-exercise lactate accumulation in athletes’ haemodynamics. Appl. Physiol. Nutr. Metab. 31, 423–431 (2006).
Kokkinos, P. Cardiorespiratory fitness, exercise, and blood pressure. Hypertension 64, 1160–1164 (2014).
Ricci, F. & Palleschi, P. Sensor and biosensor preparation, optimization and applications of Prussian Blue modified electrodes. Biosens. Bioelectron. 21, 389–407 (2005).
Zhao, J. et al. A fully integrated and self-powered smartwatch for continuous sweat glucose monitoring. ACS Sens. 4, 1925–1933 (2019).
Emaminejad, S. et al. Autonomous sweat extraction and analysis applied to cystic fibrosis and glucose monitoring using a fully integrated wearable platform. Proc. Natl Acad. Sci. USA 114, 4625–4630 (2017).
This research was supported by the UCSD Center of Wearable Sensors (CWS) and National Institutes of Health (grant no. 1R21EB027303-01A1). J.R.S. acknowledges support from CNPq (grant no. 216981/2014-0). E.D.l.p. acknowledges support from a UC MEXUS–CONACYT collaborative fellowship (2017–2022). A.A.K. acknowledges support from the Fulbright Egyptian Scholar Program (grant no. ay2019-2020). T.S.-a. acknowledges the Royal Golden Jubilee PhD scholarship of the Thailand Research Fund. We thank the Kraton Corporation for providing the SEBS samples.
The authors declare no competing interests.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Sempionatto, J.R., Lin, M., Yin, L. et al. An epidermal patch for the simultaneous monitoring of haemodynamic and metabolic biomarkers. Nat Biomed Eng 5, 737–748 (2021). https://doi.org/10.1038/s41551-021-00685-1
Nature Reviews Materials (2021)
Metabo-tip: a metabolomics platform for lifestyle monitoring supporting the development of novel strategies in predictive, preventive and personalised medicine
EPMA Journal (2021)
Journal of Pharmacokinetics and Pharmacodynamics (2021)