Particulate matter (PM) and volatile organic compounds (VOCs) are recognised as hazardous air pollutants threatening human health. Disposable filters are generally used for air purification despite frequent replacement and waste generation problems. However, the development of a novel regenerable and robust filter for long-term use is a huge challenge. Here, we report on a new class of facile water-washing regenerable ceramic catalyst filters (CCFs), developed to simultaneously remove PM (>95%) and VOCs (>82%) in single-pass and maximized space efficiency by coating the inner and outer filter channels with an inorganic membrane and a Cu2O/TiO2 photocatalyst, respectively. The CCFs reveal four-fold increase in the maximum dust loading capacity (approximately 20 g/L) in relation to conventional filters (5 g/L), and can be reused after ten regeneration capability with simple water washing retaining initial PM and VOC removal performances. Thus, the CCFs can be well-suited for indoor and outdoor air purification for 20 years, which shows a huge increase in lifetime compared to the 6-month lifespan of conventional filters. Finally, we believe that the development and implementation of CCFs for air purification can open new avenues for sustainable technology through renewability and zero-waste generation.
Particulate matter (PM) and volatile organic compounds (VOCs) are hazardous air pollutants in outdoor and indoor air. The impact of these pollutants on human mortality is well-documented, in which PM is a leading cause of death1, and many VOCs are known carcinogens2. The general approach to controlling air pollution has been to decrease emissions. Air pollution from anthropogenic emissions is not just a local and acute problem; it is also a global and chronic problem as evidenced through terrible events such as the Great smog in London in 1952 caused by sulphates from coal fuel combustion and the Los Angeles smog in 1943 caused by nitrates from automotive emission. However, the removal of pollutants through air filtration can also be an effective approach both indoors and outdoors3,4.
Currently, the high-efficiency particulate air (HEPA) polymers and fibre filtration that utilises electrostatic force is considered to be the best solution for the removal of PMs5,6. However, the replacement and discarding of filters pose a serious issue leading to additional waste and generation of carbon emission from the incineration of used filters. To overcome this disadvantage, ceramic filters (CFs) used in automotive applications are considered as a suitable candidate for the next-generation filter supporting facile regeneration. CFs have generally been used to remove PM from the exhaust gases emitted from diesel engines, which involves two types of filtration mechanisms, namely deep-bed and cake filtrations. The dominant mechanism in a clean filter is initially deep-bed filtration during which the particulates are deposited inside the porous wall. As the dust load increases, a particulate layer (i.e., the “cake”) is formed along the wall surface in the inlet channels and cake filtration becomes the prevailing mechanism7. Soot, which is a PM, is initially captured through the deep-bed filtration and later deposited as a cake. However, the capture of PM via cake filtration would be more preferable because PM captured by deep-bed filtration cannot be easily removed from the CF during regeneration, which requires hot airflow and plasma flame at high temperatures7,8. As to the removal of VOC, activated carbons have generally been used with a sorption method under ambient conditions. However, they have similar problems to PM filters, which are disposable, have a low adsorption capacity, and cannot be used for long periods. To address these problems, a catalytic honeycomb CFs have been utilised. However, the automotive catalysts coated on the CF have been shown to be easily sintered and degraded during regeneration with high temperature9,10,11. Therefore, it is necessary to develop a filter that can be easily regenerated and simultaneously removes PM and VOC operated under ambient conditions. Thus, we considered photocatalysts as one of the most promising candidates owing to their unique properties such as strong oxidation ability, biological and chemical inactivity, and operation at room temperature12. UV photocatalytic oxidation (PCO) reactions using reactive oxygen species (ROS), such as hydroxyl radical (∙OH) and superoxide anion (∙O2−) generated from the photocatalyst under UV light irradiation, not only effectively remove and decompose VOCs13,14 but also disinfect bacteria and viruses15. Although their photocatalytic capability is limited, and their reaction rate is low due to their wide band–gap energy and fast recombination of the photo–induced electron–hole pairs16,17, they still have a great advantage of operating under ambient conditions such as room temperature, unlike general thermal catalysts.
Herein, we introduce a ceramic catalyst filter (CCF) as a new class of filter that simultaneously removes PMs and VOCs as primary air pollutants, and can be regenerated and used for long periods by simple water washing. Our concept aims to achieve a renewable robust filter wherein PMs are collected with the CF, VOC gases are decomposed by a coated photocatalyst operating under ambient conditions, and reuse is by simple washing with water. For proof of concept (PoC), we improved the PM removal efficiency by applying an additional inorganic membrane coating on the channel of the bare-CF for rapidly enhancing the cake filtration step. We also attempted to employ a UV-activated photocatalyst to decompose VOCs, which was coated over the outlet channel surface of the CF to prevent catalyst deactivation by PM. The enhanced photocatalytic activity was obtained by applying the developed Cu2O/TiO2 catalyst. In addition, we proved facile regeneration and use for long-lifetime of CCF compared with conventional HEPA filter by simple water-washing. Finally, we confirmed the CCF performance by employing a CCF filter panel system for purifying the in-flowing air in buildings and a free-standing air purification system as a proto located at the public spaces with ingress of outside air.
Rational design concept of CCF
The design of CCF is based on a novel concept, wherein PMs are collected in the inlet channel of the ceramic filter, and VOC gases are decomposed by a photocatalyst coated in the outlet channel, under ambient conditions. This design concept of CCF can provide a definite advantage of being able to remove various air pollutants in the space of itself. The CF possesses an inlet channel with plugs and a porous inner wall, through which the air flows toward the outlet channel after penetrating the wall (Fig. 1). First, we selected a commercial CF designed with a conjugated plug to allow wall-flow through the porous wall for in-flowing air18,19. The filtration mechanism of CF to remove PM is a combination of deep-bed and cake filtrations, as shown in Fig. 17. The greatest advantage of CF as PM removal filter is that the surface area over volume of the filter porous wall (m2/m3) is much larger than that of other filters prepared by polymers and fibres, which enables it to be used for longer durations19. Concerning regeneration, ceramics fired at high temperatures exhibit strong heat- and water-resistant properties and are also used as water-treatment membranes20. In addition to PM removal, we used it as a support for photocatalysts to oxidise VOCs to CO2 under ambient conditions without thermal sources, as shown in Fig. 1. The photocatalysts can remove VOC by the PCO reaction using ROS such as hydroxyl radical (∙OH) and superoxide anion (∙O2−) generated from the photocatalyst under UV light irradiation at room temperature. Our novel design concept entails that, along sequential air flow, PM are first captured by the ceramic porous wall at the inlet channel with initial deep-bed and following cake filtration mechanism, and then VOCs exiting the porous wall are decomposed using the PCO reaction by the UV–photocatalyst system at the outlet channel. Finally, to realise this concept, we also attempted an uncommon method of catalyst coating over the outlet channel surface for preventing catalyst deactivation by PM.
For the rational design of CCF, we prepared commercial ceramic filters with 100, 200, and 300 CPSI, where CPSI implies cells per square inch of the filter. To determine the optimal length of CCF, we investigated the pressure drop of the filters along the CF length using a pressure drop model developed by Masoudi et al7. and Konstandopoulos & Johnson21 (Supplementary Fig. 1). The flow characteristics such as distributions of velocity and pressure of CFs inside each CF channel were investigated using computational fluid dynamics (CFD) simulations (Supplementary Fig. 2a). Using this developed model, the porous-wall lengths were optimised to 60–120 mm, which indicate the ranges of minimum pressure drop (Supplementary Fig. 2b). The predicted pressure drop was estimated to be 71 Pa at an optimal porous-wall length of 105 mm (Supplementary Table 1). Based on these results, commercial CFs with a filter length of 115 mm with each plug of 5 mm were procured from Corning Co. with 200 CPSI and 8.0 mil wall thickness (0.203 mm). Thus, the CF having an optimal length was carefully employed to prepare the CCF.
PM removal by surface treatment
Figure 2a illustrates the internal cross-section morphology along the filter length describing a specific feature of the CCF. According to the filtration mechanism of the CF, an air flow with PMs and gaseous air pollutants that entered into the filter would penetrate through the porous wall, where only PMs can be captured on and/or in the pores of the wall. The core of the CCF that removes PM is obtained by an additional surface coating treatment of metal oxide, known as the “membrane”. The morphology of the porous surface with microstructures before and after the membrane coating on the bare-CF can be seen in the scanning electron microscope (SEM) images (Fig. 2b, Supplementary Fig. 3). The membrane with a net-type shape was uniformly spread over the wall surface in the filter channel. The vertical cross-section of the CF shows well-coated membrane layers on the inner wall surface (Fig. 2c), and the characteristic membrane component (Bi) is observed along the wall, which is mainly composed of Mg in cordierite (Fig. 2d). The mean pore size after membrane coating was reduced from 11.6 to 8.2 μm while maintaining the porosity of CF (Supplementary Fig. 3c). It is well known that the pore size reduction could affect permeability related to filter efficiency. In particular, the control of mean (average) pore size plays a critical role in determining the quality factor, including filter efficiency (FE) and pressure drop22,23. We evaluated the filter efficiency (FE, %) and pressure drop (Δp, Pa) under a single-pass test condition of an air flow of 1 m/s by using a customised aerodynamic equipment. Compared to the bare-CF, the membrane coated filter achieved an enhanced PM10 (particulate matter, size below 10 μm) FE of 98% and PM2.5 (particulate matter, size below 2.5 μm) FE of 97.7%, respectively (Table 1). It plays an important role in successfully removing PMs by cake filtration mechanism beyond the initial deep-bed filtration through the CF7. Here, we improved the filtration mechanism by membrane coating, which resulted in a significant increase in the FE of PM1 (particulate matter, size below 1 μm) as detailed in Table 1.
VOC removal by coating of synthesized photocatalyst
To remove VOC by the CCF, we developed a Cu2O-TiO2 catalyst based on a TiO2 (anatase) photocatalyst. Cu2O having Cu1+ can act as a co-catalyst in the conduction band as an electron acceptor, further producing ROS such as superoxide anion (∙O2−) (Fig. 1)24,25. The oxidation state of Cu on the surface of TiO2 was confirmed to be Cu1+ by X-ray photoelectron spectroscopy (XPS) analysis and Raman spectroscopy (Supplementary Fig. 4a, b). The basic characterisations, such as UV–visible absorbance and electrochemical impedance spectroscopy (EIS), were measured (Supplementary Fig. 4c, d). The PCO reaction activity of Cu2O/TiO2 catalyst can be improved because Cu2O behaves as an electron acceptor, leading to easy separation of hole–electron pairs and reduction of hole–electron recombination26. To verify this mechanism, we evaluated the electrochemical characteristics by measuring the photocurrent density, Mott–Schottky plot, and photoluminescence (PL) (Fig. 3a–c). With these enhanced characteristics of the Cu2O/TiO2 catalyst, we measured the intrinsic formaldehyde decomposition activity of powder catalysts (TiO2, CuO/TiO2, and Cu2O/TiO2) under relative humidity (RH) 0% and RH 50% conditions, resulting in 93% @ Cu2O/TiO2 > 84% @ CuO/TiO2 > 78% @ TiO2 at RH 50%, which was higher than that at RH 0% owing to the formation of hydroxyl radical (∙OH) by the oxidation reaction with water (Fig. 3d)12,14. Furthermore, we assessed the removal efficiencies with five representative VOCs, namely formaldehyde, ammonia, acetaldehyde, acetic acid, and toluene gas, over 1 g of Cu2O/TiO2 catalyst coated on honeycomb (Fig. 3e). The average removal efficiency was 82.4%, with the highest being 93% for acetic acid and the lowest being 62% for toluene. Therefore, we confirmed the development of a new TiO2-based catalyst via Cu2O as co-catalyst, which improves the photocatalytic activity through facile charge separation and high charge carrier density. For the Cu2O/TiO2 catalyst, we coated similar amounts of catalysts for fabricating CCFs (38–40 g of Cu2O/TiO2 or TiO2 catalysts per apparent volume of the filter (L)), where we initially used the CF without the membrane to confirm the catalyst performance. Enhanced reaction efficiencies (REs: VOC removal and CO2 production) of nearly 90% using the Cu2O/TiO2 catalyst were obtained with CO2 as the product gas, while those using TiO2 were 76% (Fig. 3f). In particular, we extensively monitored the feasible side gas-phased products of PCO reaction, including CO by Fourier transform infrared spectroscopy (FT-IR) along the reaction time, but these were not detected (Fig. 3g). This implies that CO2 was the only product resulting from the PCO reaction. Thus, we concluded that all the reacted HCHO gases were perfectly decomposed into CO2 gas by the PCO reactions over the Cu2O/TiO2 catalyst. We used formaldehyde (HCHO), which is a well-known as highly carcinogenic gas2, as a representative VOC for the removal test (see Methods). The light intensity test and ray tracing simulation (Zemax) were conducted to optimise the UVA-LED system (Supplementary Figs. 5 and 6). We set up the UV-activated system optimally with a light source using a 2 × 2 UVA LED array with a suitable light intensity of 38.1 (centre) and 40.8 mW/cm2 (side), and a maximum light propagation distance of approximately 30 mm inside the CCF.
Fabrication of CCF
Figure 4a shows a snapshot of the dip-coating of the catalyst with membrane-coated CF for CCF fabrication. When the membrane coated CF was dipped in the catalyst coating slurry, the slurry is not absorbed into the cell, implying no penetration beyond the wall. It is an important design rule that the catalyst should be coated on the outlet channel surface against air flow to prevent deactivation by PM. To observe the inside of the cell (channel), we conducted SEM analysis along with Electron Probe X-ray Microanalysis (EPMA) to confirm the spatial distribution of the main elements in the cell. Figure 4b shows the SEM image of cross-sectional CCF and the element mapping of Ti, which indicates a well-coated catalyst layer on the inner channel surface of CCF. The SEM image shows the wall centre of CCF, which indicates the inside pores (black), coated catalysts (grey), and membranes (white). The mapping image of Ti demonstrates that the catalyst was coated on a single side including the inside wall, implying that no penetration of the coating occurred to the other side (membrane coating zone). Although the inability of the slurry to penetrate the membrane was not investigated in this study, it may be caused by the micro/nano structures generated by the surface treatment (membrane coating) as per Cassie–Baxter27. For practical CCF fabrication, we confirmed the relationship among the pressure drop, FE, and RE (or removal efficiency) along the catalyst coating lengths (Fig. 4c, d). The pressure drop increased exponentially along the coating length; however, it was stable up to the 50 mm coating zone. FE decreased gradually as the coating length increased. However, RE achieved an optimum value at the 50 mm coating zone. Thus, we obtained the optimum specifications to fabricate the CCF for practical applications from systematic testing along the catalyst coating length (Fig. 4d, Supplementary Table 2). In addition, to better understand the characterisation along the coating zone length, we investigated the wall-normal velocity along the CF length using CFD simulations (Fig. 4e). The wall-normal velocity passing through the inner wall of the CF increases from above 30% of the total CF length to the maximum at the outlet channel, which implies the photocatalytic reaction might be the most effective within 70% of the total CF length from the outlet.
Regeneration performances of CCF
Among the various regeneration methods such as water washing by water flow and sonication, we found that simple water washing in the direction against PM capture in CF or CCF is the most effective way to clean dust and regenerate the initial pressure drop of the filter (Supplementary Fig. 7a, b). The maximum dust loading capacity of CF up to final pressure drop (~250 Pa) was evaluated to be approximately 20–30 g/L, while the normal disposable HEPA or medium filters (MFs) for 6 months have a maximum capacity of 5 g/L (Supplementary Fig. 7c)28. For ten regenerations by water washing, the CF achieved an accumulated dust loading capacity exceeding 216 g/L, while maintaining an efficiency loss of barely 9% compared to the high initial efficiency of 98% at a high linear velocity of 1 m/s (Fig. 5a). However, as the regeneration cycle progressed, the commercial HEPA filter rapidly decreased in its dust loading capacity (48.4 g/L for ten regenerations) and could no longer be operated (Fig. 5b). The CF may possibly indicate a usage of 2 years without regeneration exceeding the maximum dust loading capacity four times that of the normal HEPA filters. Thus, it implies that we can use the CF for 20 years through ten regenerations of simple water washing. Finally, we simultaneously achieved PM and HCHO removal using CCF (Fig. 5c). For the CCF with Cu2O/TiO2 catalyst, the PM10 FE, HCHO removal efficiency, and pressure drop initially were about 95%, 82%, and 20 Pa at 10 L/min (linear velocity of 0.12 m/s), respectively. Unprecedentedly, these high performances are maintained even after ten regenerations with simple water washing. This result is firstly demonstrated by the CCF as a new class of filter realised using our main concept suggested in this study. Thus, with simple water washing, we achieved the facile regeneration of the CCF.
Application for air purification system
Prior to using the CCF as a prototype for various applications, we first applied the CF panel system to purify the air entering a building to replace current commercial MF (Ultra Low Pressure Drop (ULPD) in heating, ventilation, and air conditioning (HVAC) systems (Fig. 6a). Through this, we confirmed practically that PM2.5 FE remains higher than 98% for 30 months without replacement and regeneration of the CF panel system, while the MF showed low FE (62%) and required replacement every 3–6 months (Fig. 6b). In addition, we developed a free-standing air purification system applying CF as another type of proto system to purify the air in the underground parking lot (Fig. 6c). Note that installation of UV light system for CCF performance is still in progress. The FEs of PM10 and PM2.5 of the system are still observed above 90% for about 12 months for a flow rate of 4000 m3/h (Fig. 6d). Note that all the evaluations are in-operation by now. Furthermore, we conducted a CFD simulation to predict the air flow and PM concentrations in huge underground parking lot (volume of 96,000 m3 for 600 cars). After 21 CCF proto systems were located, air flow was more uniformly distributed without a quiescent zone, and the overall volume averaged PM10 concentration showed a surprising reduction of 32% (Supplementary Fig. 8). To confirm the prediction result of the CFD simulations, we practically test the spatial efficiency using 21 installed CCF proto systems.
In summary, we first designed a new class of facile regenerable CCF for the simultaneous removal of PM and VOC under ambient conditions using membraned porous wall flow filtration and UV-activated photocatalyst in the porous CF for air purification. The structurally innovative design of CCF by two components (membrane and photocatalyst) can offer a great advantage of space efficiency to simultaneously remove various air pollutants. Indeed, the new filter system based on our proposed concept exhibited a PM FE of about 95% and VOC RE of about 82% with perfect PCO reaction to form CO2 under single-pass air flow condition. The Cu2O/TiO2 catalyst can improve the VOC (HCHO) RE by trapping electrons from TiO2 as well as by preventing recombination of electron–hole pairs on the catalyst. Furthermore, we demonstrated that the CCF filter can be fully regenerated by simple water washing, and the high removal performance of the filter is sustained even after ten regeneration cycles. The CCF can possibly indicate a usage of 2 years without regeneration, with nearly four times the maximum dust loading capacity than that of conventional HEPA filters, suggesting long-lifetime for 20 years through ten regeneration cycles via simple water washing. The facile regenerable, long-lifetime filter system proposed in this study is expected to provide a new paradigm for indoor and outdoor air purification through sustainable technology.
Preparation of Cu2O/TiO2 catalyst
The Cu2O/TiO2 catalyst was prepared by an impregnation method. CuCl2 (0.5 wt.%) was dispersed in a TiO2 suspension. The suspension was heated at 90 °C and maintained for 1 h in a water bath under stirring. Glucose and NaOH were added to the prepared suspension, which was heated at 90 °C and maintained for 1 h in a water bath under stirring and then dried at 110 °C. Glucose and NaOH were added to reduce CuO to Cu2O to control the oxidation state of Cu. The chemicals used in this study included TiO2 (ST-01, anatase, Ishihara Inc., Japan), D-(+)-Glucose (Aldrich, USA), CuCl2 (Aldrich, USA), and NaOH (Aldrich, USA).
The UV-visible spectra of the catalyst were recorded by a UV-visible spectrophotometer equipped with a diffuse reflectance attachment (Solidspec-3700, Shimadzu, Japan). The catalysts were characterised by X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, and Brunauer–Emmett–Teller (BET) surface area analysis. The (photo)electroanalytical measurements were obtained through the photocurrent density, electrochemical impedance spectroscopy (EIS) Nyquist plot, and Mott–Schottky plot. Photoluminescence (PL), for evaluating the charge recombination rate, was also performed. A single compartment cell with a three-electrode configuration was employed, which included working, Pt counter, and an Ag/AgCl reference electrodes under UV irradiation (at 365 nm LED).
Preparation of CCF: membrane coating
The Commercial CFs were provided by Corning. The membrane coating in the filter was prepared from metal oxide nanoparticles. The nanoparticle deposition in the filter was performed by passing the particle-laden flow through a targeting filter in the gas-phase during the membrane coating process. Finally, the high porous net-type membrane was prepared after calcination. The CF wall surface was measured using an image from a scanning electron microscope (SEM) (FE-SEM JEOL, JSM-7900 and SEM JEOL, SEM-5610). To observe the SEM image of the cross-sectional CF wall, the CCF fragment was moulded in epoxy and polished to reveal the CF wall surface. In addition, SEM analysis equipped with Electron Probe X-ray Microanalysis (EPMA, EPMA-1720, Shimadzu, Japan) was employed to observe the distribution of main elements.
Preparation of CCF: catalyst washcoating
The CCFs were prepared by washcoating TiO2 (ST-01) and Cu2O/TiO2 (SAIT) catalysts on a 200/8.0 CPSI/mil membrane coated with CFs, conducted by a simple dipping method. Before coating, the catalyst powder was completely suspended in water using a wet-type agitator bead mill (LabStar LS1, NETZSCH, Germany) to maintain a well-mixed solution during washcoating. The mean particle size of the powder in the slurry was 1.84 and 2.57 µm for the TiO2 and Cu2O/TiO2 catalysts, respectively, as determined by the particle size analyser (1090, CILAS, France). The dipping for washcoating was maintained for approximately 2–3 min. The solid content of the catalyst slurry was 40 g/L. Note that g/L indicates the catalyst weight (g) over the apparent volume of CF (L). The wall surface of CCF was measured using an image from a scanning electron microscope (SEM) (FE-SEM, SU-8030, Hitachi, Japan). The catalyst was coated with reasonable uniformity; however, the catalyst thickness on the wall surface could not be quantitatively measured owing to its high porosity which exceeded 50%. The CCFs after washcoating were dried overnight at 80–200 °C.
Regeneration method by simple water washing
The CCF regeneration was conducted by simple washing using distilled ionised water. After performing the PM and VOC removal evaluations, the CCF was treated by water flow against the PM capture direction for 10 min. After this simple regeneration, the filter was dried overnight at 80–100 °C under vacuum conditions.
Evaluation of removal efficiencies of PM and VOCs
For PM removal performance evaluation, the single-pass test for CCF was conducted using customised aerodynamic equipment. The pressure drop was also measured during the test. The air flow velocity was maintained at 1 m/s. The dimensions of the prepared CCF sample were 38 × 38 × 115 mm. For PM generation, a 1.5 wt.% KCl solution was used and the dried KCl particles were exposed to the aerodynamic equipment for the single-pass test. Also, Arizona dust (A1 dust, SiO2: main component) was mainly employed to compare the regeneration performance between CCF and HEPA. Note that, however, KCl particles had to use to avoid the interference effect such as adsorption of VOC on SiO2 (Arizona dust) to conduct the simultaneous removal test of PM and VOC. The particle numbers and weights before and after filtration were obtained by an optical particle sizer (OPS) analyser (Model 3330, TSI, USA). The intrinsic powder catalyst-assisted VOC (HCHO) removal activity was performed in the continuous-flow mode. The VOC gas was continuously fed into the stainless-steel photo-reactor with quartz window at a total flow rate of 0.5 L/min under RH 0% and RH 50% conditions at 25 oC. For the removal test of five VOCs, we used 100 CPSI honeycomb blocks with size of 35 × 70 × 10 mm coated with 1 g of Cu2O/TiO2 powder. The 10 ppm decrease of each VOC by photocatalytic reaction was continuously measured in a 100 L chamber test for 30 min. The measurements were sequential in the following order: formaldehyde, ammonia, acetaldehyde, acetic acid, and toluene gases. For CCF, the customised Teflon reactor was equipped with an optical polished quartz window at a total flow rate of 10 L/min. The HCHO concentration in the air balance was 25 ppm. The sample in the reactor was illuminated using a 365-nm UV-LED (Fibre Optics Korea Co., Republic of Korea). The concentrations of consumed HCHO and formed CO2 were monitored using an FT-IR spectrometer (I4001-E, MIDAC Co., USA) to calculate the VOC removal efficiency and produced CO2 gas, respectively. For simultaneous PM and VOC removal test, we fitted the customised aerodynamic equipment with an optical polished quartz window to apply the UV-LED. The test was performed at a total flow rate of 10 L/min where KCl particles as PM and HCHO as VOC were included in the air flow. The HCHO concentration in the air balance was 10 ppm. The pressure drop, PM concentration, and VOC (reactant) and CO2 (product) concentrations were measured using pressure gauges installed in the customised aerodynamic equipment, OPS, and FT-IR spectrometer for the same time assessment, respectively.
CFD and optic simulations
A CFD simulation was conducted using commercial CFD code (ANSYS Fluent 2020R2). The 3D steady Reynolds-averaged Navier-Stokes (RANS) equations, together with the realisable k-ε model and passive scalar transport equation with gradient-diffusion hypothesis were solved for the fluid flow and dispersion of PM, respectively, where PM was regarded as a passive scalar and the turbulent Schmidt number was taken as 0.729,30. The traffic-related PM emission and the PM removal process of air purification systems were modelled as a source/sink term in the scalar transport equation (see Supplementary information for details). The SIMPLE algorithm was used for pressure-velocity coupling, and second-order discretisation schemes were applied for all spatial derivatives. Ray tracing simulation was performed using Zemax Optical Design Software. All parameters of the LED source were modelled in accordance with manufacturer specifications. For the simulation, surface characterisation of the TiO2 coating was considered to have an absorption/reflection ratio of 73/27 based on the experimental results.
The data that supports the findings of this study are available from the corresponding author on reasonable request.
Murray, C. J. L. et al. Global burden of 87 risk factors in 204 countries and territories, 1990–2019: a systematic analysis for the Global Burden of Disease Study 2019. Lancet 396, 1223–1249 (2020).
Strum, M. & Scheffe, R. National review of ambient air toxics observations. J. Air Waste Manag. Assoc. 66, 120–133 (2016).
Anderson, K. & Peters, G. The trouble with negative emissions. Science 354, 182–183 (2016).
Tanzer, S. E. & Ramirez, A. When are negative emissions negative emissions? Energy Environ. Sci. 12, 1210–1218 (2019).
Brown, R. C. Air filtration: An integrated approach to the theory and applications of fibrous filters (Pergamon Press, 1993).
Zhang, W., Deng, S., Wang, Y. & Lin, Z. Dust loading performance of the PTFE HEPA media and its comparison with the glass fibre HEPA media. Aerosol Air Qual. Res. 18, 1921–1931 (2018).
Masoudi, M. et al. Validation of a model and development of a simulator for prediction the pressure drop of diesel particulate filters. SAE paper No. 2001−01−0911 (2001).
Lee, D. H. et al. Active regenerative DPF using a plasma assisted burner. SAE paper No. 2009−01−1926 (2009).
Zotin, F. M. Z., Gomes, O., de Oliveira, C. H., Neto, A. A. & Cardoso, M. J. B. Automotive catalyst deactivation: Case studies. Catal. Today 107–108, 157–167 (2005).
Bartholomew, C. H. Mechanism of catalyst deactivation. Appl. Catal. A: Gen. 212, 17–60 (2001).
Kwon, H. J., Kim, Y., Nam, I.-S., Jung, S. M. & Lee, J.-H. The hydrothermal stability of paper-like ceramic fiber and conventional honeycomb-type cordierite substrates washcoated with Cu-MFI and V2O5/TiO2 catalysts for the selective catalytic reduction of NOx by NH3. Top. Catal. 53, 439–NH446 (2010).
Hoffmann, M. R., Martin, S. T., Choi, W. & Bahnemann, D. W. Environmental applications of semiconductor photocatalysis. Chem. Rev. 95, 69–96 (1995).
Weon, S. & Choi, W. TiO2 nanotubes with open channels as deactivation-resistant photocatalyst for the degradation of volatile organic compounds. Environ. Sci. Technol. 50, 2556–2563 (2016).
Shayegan, Z., Lee, C.-S. & Haghighat, F. TiO2 photocatalyst for removal of volatile organic compounds in gas phase−A review. Chem. Eng. J. 334, 2408–2439 (2018).
Zheng, X. et al. Photocatalytic disinfection performance in virus and virus/bacteria system by Cu-TiO2 nanofibers under visible light. Environ. Pollut. 237, 452–459 (2018).
Park, H., Park, Y., Kim, W. & Choi, W. Surface modification of TiO2 photocatalyst for environmental applications. J. Photochem. Photobiol. C. 15, 1–20 (2013).
Marschall, R. Semiconductor composites: strategies for enhancing charge carrier separation to improve photocatalytic activity. Adv. Funct. Mater. 24, 2421–2440 (2014).
Mohan, S., Dinesha, P. & Kumar, S. NOx reduction behavior in copper zeolite catalysts for ammonia SCR systems: A review. Chem. Eng. J. 384, 123253–123262 (2020).
Heck, R. M., Farrauto, R. J. & Gulati, S. T. Catalytic air pollution control: Commercial technology, 2nd edition (John Wiley & Sons, 2002).
Pendergast, M. M. & Hoek, E. M. V. A review of water treatment membrane nanotechnologies. Energy Environ. Sci. 4, 1946–1971 (2011).
Konstandopoulos, A. G. & Johnson, J. H. Wall-flow diesel particulate filters-their pressure drop and collection efficiency. SAE Trans. 98, 625–647 (1989).
Li, P., Wang, C., Zhang, Y. & Wei, F. Air filtration in the free molecular flow regime: A review of high-efficiency particulate air filters based on carbon nanotubes. Small 10, 4543–4561 (2014).
Zhang, G.-H. et al. High-performance particulate matter including nanoscale particle removal by a self-powered air filter. Nat. Commun. 11, 1653–1662 (2020).
Kumar, S. et al. Facile synthesis of hierarchical Cu2O nanocubes as visible light photocatalysts. Appl. Catal. B: Environ. 189, 226–232 (2016).
Sang, W., Zhang, G., Lan, H., An, Z. & Liu, H. The effect of different exposed facets on the photoelectrocatalytic degradation of o-chlorophenol using p-type Cu2O crystals. Electrochim. Acta 231, 429–436 (2017).
Wang, M. et al. p-n Heterojunction photoelectrodes composed of Cu2O-loaded TiO2 nanotube arrays with enhanced photoelectrochemical and photoelectrocatalytic activities. Energy Environ. Sci. 6, 1211–1220 (2013).
Cassie, A. B. D. & Baxter, S. Wettability of porous surfaces. Trans. Faraday Soc. 40, 546–551 (1944).
Liu, B., Zhang, S., Wang, X., Yu, J. & Ding, B. Efficient and reusable polyamide-56 nanofiber/nets membrane with bimodal structures for air filtration. J. Colloid Interf. Sci. 457, 203–211 (2015).
Blocken, B., Vervoort, R. & van Hooff, T. Reduction of outdoor particulate matter concentrations by local removal in semi-enclosed parking garages: a preliminary case study for Eindhoven city center. J. Wind Eng. Ind. Aerodyn. 159, 80–98 (2016).
Vervoort, R., Blocken, B. & van Hooff, T. Reduction of particulate matter concentrations by local removal in a building courtyard: Case study for the Delhi American Embassy School. Sci. Total Environ. 686, 657–680 (2019).
This work was supported by Samsung Electronics Co., Ltd. We are grateful to Corning Research Centre China for proving the ceramic filters. We thank the former head of institute Prof. Jhoon Kim of Yonsei University as supervisor for this work. We also thank our new colleagues Dr. Jun Kyu Kim, Dr. Sungwoo Kang, Dr. Kang Hee Cho, Dr. Jaehee Chang, Dr. Joon Woo Park, and Dr. Noho Lee for providing helpful suggestions in preparing this manuscript.
H.J.K., S.M.J., H.C., and H.C.L. are inventors on a registered patent related to this work filed by Samsung Electronics Co. Ltd. (US Patent No. 11,491,475 B2, filed November 8, 2022). The authors declare no other competing interests.
Peer review information
Nature Communications thanks the anonymous reviewer for their contribution to the peer review of this work. Peer reviewer reports are available.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Kwon, H.J., Yang, D.S., Koo, M.S. et al. Long-lifetime water-washable ceramic catalyst filter for air purification. Nat Commun 14, 520 (2023). https://doi.org/10.1038/s41467-023-36050-w
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.