Skip to main content

Thank you for visiting You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Reaching the ultimate energy resolution of a quantum detector


Quantum calorimetry, the thermal measurement of quanta, is a method of choice for ultrasensitive radiation detection ranging from microwaves to gamma rays. The fundamental temperature fluctuations of the calorimeter, dictated by the coupling of it to the heat bath, set the ultimate lower bound of its energy resolution. Here we reach this limit of fundamental equilibrium fluctuations of temperature in a nanoscale electron calorimeter, exchanging energy with the phonon bath at very low temperatures. The approach allows noninvasive measurement of energy transport in superconducting quantum circuits in the microwave regime with high efficiency, opening the way, for instance, to observe quantum jumps, detecting their energy to tackle central questions in quantum thermodynamics.


Almost a century ago, Johnson and Nyquist1,2 presented evidence of fluctuating electrical current and the governing fluctuation dissipation theorem (FDT). Whether, likewise, temperature \(T\) can fluctuate is a controversial topic and has led to scientific debates for several decades3,4,5,6,7. Consider a system with coupling to a heat bath at temperature \(T\) for which the classical FDT of fluctuations \({S}_{\dot{Q}}^{{\rm{eq}}}\) of heat current \(\dot{Q}\) holds in form \({S}_{\dot{Q}}^{{\rm{eq}}}=2{k}_{B}{T}^{2}{G}_{{\rm{th}}}\) in equilibrium. Here, \({G}_{{\rm{th}}}\) is the heat conductance to the bath. We can write the energy balance equation \(\dot{Q}={\mathcal{C}}{\mathrm{d}}\widetilde{T}/{\mathrm{d}}t\) for the temperature of the system \(\widetilde{T}(t)=T+\delta T(t)\) at time \(t\), where \({\mathcal{C}}\) denotes the heat capacity. The heat current is composed of its expectation value \(-{G}_{{\rm{th}}}\delta T\) and fluctuations \(\delta \dot{Q}\) around it. There are two origins of noise in this heat current: (1) the standard randomness of transport known for particle current noise (time randomness), and (2) random energies exchanged, leading to enhancement of fluctuations on top of those known for particle current only. We obtain the noise spectrum of temperature of the system by Fourier transformation as \({S}_{T}(\omega )=\int dt{e}^{i\omega t}\langle \delta T(t)\delta T(0)\rangle\). This yields under steady state conditions

$${S}_{T}(\omega )=\frac{2{k}_{B}{T}^{2}}{{G}_{{\rm{th}}}}\frac{1}{1+{\omega }^{2}{{\mathcal{C}}}^{2}/{G}_{{\rm{th}}}^{2}}.$$

At low frequencies we have


and the spectrum has Lorentzian cutoff at \({\omega }_{c}={G}_{{\rm{th}}}/{\mathcal{C}}\). These results hold also for a system coupled to several equilibrium baths, if one takes \({G}_{{\rm{th}}}\) to represent the sum of all the individual thermal conductances to these baths. For the root-mean-square (rms) fluctuations we obtain the well-known result3 \(\langle \delta {T}^{2}\rangle =\int_{-\infty }^{\infty}\frac{d\omega }{2\pi }{S}_{T}(\omega )={k}_{B}{T}^{2}/{\mathcal{C}}\).

Here, we measure the time-dependent temperature of the absorber of a nano-calorimeter at low mK temperatures both under equilibrium and nonequilibrium conditions. We observe that the equilibrium fluctuations follow the fluctuation dissipation theorem (FDT) for temperature. Ideally, the noise of this calorimeter permits measurements of microwave photons in GHz regime at the lowest temperatures that we achieve. This method is then a way to observe calorimetrically, e.g., the quantum trajectories with superconducting circuits8,9,10.


The calorimeter

In a fermionic system, like the electrons (about \(1{0}^{8}\) of them) in the nano-calorimeter in the present experiment, temperature is coded in the Fermi distribution \(f(\epsilon )={[{e}^{(\epsilon -\mu )/{k}_{{\rm{B}}}T}+1]}^{-1}\), which directly determines the readout signal of our thermometer. Here, \(\epsilon\) and \(\mu\) denote the single particle energy and chemical potential of the system, respectively. We illustrate the calorimeter11,12,13,14,15 principle of our experiment and set-up in Fig. 116. The electron system (absorber), is coupled to the phonon heat bath at constant temperature \(T\) via electron–phonon collisions, which lead to stochastic exchange of heat, as indicated by the many vertical arrows between the two in Fig. 1a. This forms the bottleneck of heat transport in a nano-calorimeter, in contrast to macroscopic calorimeters. The red arrows from the left depict the electronic injection of heat under nonequilibrium conditions, fluctuating due to the stochastic nature of tunneling. By attaching a fast thermometer to the absorber, one records its time \(t\) dependent temperature fluctuations \(\delta T(t)\) as shown by a measured time trace. The actual sample (scanning electron micrograph in Fig. 1b) is realized as a \(\ell =1\,\) µm long copper normal-metal absorber (brown) connected to three superconducting leads (blue). The right one is a tunnel contact of the thermometer and the other tunnel junction on the left the hot electron injector. The third one pointing down and \(50\) nm away from the thermometer, is a direct clean metal-to-metal contact grounded at the sample stage. It provides a fixed chemical potential for the absorber and induces proximity superconductivity to the thermometer facilitating its proper operation. The measuring set-up for the thermometer junction shown on the right side of Fig. 1b consists of a parallel on-chip \(LC\) resonator, coupled to input \({V}_{1}\) and output \({V}_{2}\) RF  (radio frequency)  lines, operating at frequency \({f}_{0}=620\) MHz, which also admits DC biasing at voltage \({V}_{{\rm{th}}}\). The measured signal \({S}_{21}\) obtained from the ratio of \({V}_{2}/{V}_{1}\) yields the conductance of the thermometer junction. It is measured at a finite sampling rate in order to acquire statistics of temporal temperature of the absorber.

Fig. 1: The set-up for measuring temperature fluctuations.
figure 1

a The calorimeter principle applied to the electronic system in this work. The normal-metal absorber in the center is subjected to the fluctuating heat current from the phonon bath below. Additionally we have an option to create nonequilibrium by injecting “hot” electrons as indicated by red arrows on the left. A key element in the calorimeter is a thermometer with sufficient bandwidth to provide temporal temperature traces, of which an example is shown above the absorber. b The measurement set-up including the colored scanning electron micrograph of the sample in the center. The \(\ell =1\,\) µm long Cu absorber (brown) coupled to two superconducting Al leads (blue) via tunnel barriers (bronze). The clean metal-to-metal contact to another superconducting Al lead pointing down at an inclined angle provides the proximity effect for the thermometer and a fixed chemical potential for the absorber. The circuit on the sample stage at low temperature (LT) within the dashed area presents the RF readout of the thermometer junction with tunnel resistance 18 k\(\Omega\) composed of an LC resonator and probed by RF transmission measurement between ports \({V}_{1}\) and \({V}_{2}\). The rest of the set-up at room temperature (RT) is for DC biasing of both the injector \((V)\) and thermometer \(({V}_{{\rm{th}}})\).

Principles of the experiment

In order to calibrate the thermometer we measure \({S}_{21}\) averaged over typically \(1\) s time interval at different bath temperatures of the cryostat, traceable to primary Coulomb blockade thermometry CBT. An example of dependence of thus obtained averaged \(\langle {S}_{21}\rangle\) on \({V}_{{\rm{th}}}\) is shown on a wide bias range in Fig. 2a. The drop of \(\langle {S}_{21}\rangle\) at about ±\(200\,\) µV is due to the superconducting gap \(\Delta\) in aluminum. The main feature, the zero bias anomaly (ZBA) at \({V}_{{\rm{th}}}=0\), which is indicated by the central red arrow, presents the basis of our thermometer. This dip originates from proximity induced supercurrent due to the presence of clean contact. Now it is placed 50 nm away from the tunnel junction, which is to be contrasted to 500 nm in our earlier work17; this way the sensitivity of the thermometer is enhanced substantially. Quantitatively, the temperature dependence of the average transmission \(\langle {S}_{21}\rangle\) at this dip is depicted in Fig. 2b. It manifests approximately linear dependence at sub \(200\) mK temperatures, emphasized by the zoom in the inset of this figure. Owing to the competing quasiparticle tunneling, there is eventually back-bending of the characteristics at temperatures above 300 mK; this leads to loss of sensitivity in the cross-over temperature range. Depending on the range of interest, we employ either linear or nonlinear calibration to convert \(\langle {S}_{21}\rangle\) to temperature. This calibration needs to be done only once for each cooldown.

Fig. 2: The transmission measurement of the RF thermometer at \(-120\) dBm input power.
figure 2

a Wide bias range transmission \(\langle {S}_{21}\rangle\) averaged over 100 repetitions at each bias point \({V}_{{\rm{th}}}\) at bath temperature \(T \sim \,100\) mK. The two red arrows indicate the working points for actual ZBA thermometry at \({V}_{{\rm{th}}}=0\) and background measurement at \({V}_{{\rm{th}}}=85\,\) µV, respectively. b The thermometer calibration against the bath temperature \(T\) in equilibrium. The inset shows the low-temperature end together with the linear fit used for the temperature fluctuation measurements.

Equilibrium fluctuations

Time domain measurements allow detecting temporal fluctuations of the quantity of interest. In our case we monitor \({S}_{21}(t)\), yielding the instantaneous temperature of the absorber at \(10\) kHz sampling rate over a chosen time interval. We collect data under given conditions typically for up to \(1\) hour. As a result we obtain the total fluctuations (variance) \(\langle \delta {S}_{21,{\rm{tot}}}^{2}\rangle\) in a bandwidth of \(\Delta f\approx 10\) kHz. This signal is composed of the amplifier and other instrumental noise \(\langle \delta {S}_{21,{\rm{bg}}}^{2}\rangle\) (“bg” stands for background), in addition to the noise of interest from the actual sample, \(\langle \delta {S}_{21}^{2}\rangle\) = \(\langle \delta {S}_{21,{\rm{tot}}}^{2}\rangle\)\(\langle \delta {S}_{21,{\rm{bg}}}^{2}\rangle\). Here, we assume uncorrelated noise from the different sources. The way we determine the \(\langle \delta {S}_{21,{\rm{bg}}}^{2}\rangle\) is explained in the Methods section. Our quantitative results depend critically on the precision of determining this background noise. Taking the linear calibration as in the inset of Fig. 2b, with the responsivity \({\mathcal{R}}\equiv | d\langle {S}_{21}\rangle /dT|\), we have for the temperature noise of the absorber \(\langle \delta {T}^{2}\rangle\) = \({{\mathcal{R}}}^{-2}\langle \delta {S}_{21}^{2}\rangle\). We exhibit in Fig. 3 the central quantity in the experiment, low-frequency temperature fluctuations \(\sqrt{{S}_{T}}=\sqrt{\langle \delta {T}^{2}\rangle /2\Delta f}\) as a function of bath temperature in equilibrium. From now on we denote \({\rm{NET}}\equiv \sqrt{{S}_{T}}\), which is the noise-equivalent temperature. The data symbols in both panels correspond to the averaged bare noise, where the best guess of the background has been subtracted. The shaded area in Fig. 3a depicts the uncertainty in determining \({\rm{NET}}\) precisely due to this subtraction. Overall, we observe first increase of \({\rm{NET}}\) upon lowering \(T\) and then gradual turn down of it at the lowest temperatures. The dominant contributions to \({G}_{\mathrm{th}}\) arise from electron–phonon coupling at higher temperatures and radiative heat transfer by thermal photons18 towards low \(T\) as

$${G}_{\mathrm{th}}=5\Sigma {\mathcal{V}}{T}^{4}+\alpha gT.$$

Here, \(\Sigma\), \({\mathcal{V}}\) are electron–phonon coupling constant19 and volume of the absorber, respectively. For the photonic contribution18, \({G}_{Q}=gT\) is the quantum of thermal conductance with \(g=\pi {k}_{{\rm{B}}}^{2}/6\hslash\). We assume the coupling coefficient \(\alpha\) to have values \(\ll\! 1\) according to earlier investigations20. Equation (2) predicts then

$${\rm{NET}} =\sqrt{\frac{2{k}_{{\rm{B}}}}{5\Sigma {\mathcal{V}}}}{T}^{-1}\,\,({\rm{high}}\, T)\\ {\rm{NET}} =\sqrt{\frac{2{k}_{{\rm{B}}}}{\alpha g}}{T}^{1/2}\,\,({\rm{low}}\, T),$$

with cross-over between the two regimes with maximum NET at the temperature \({T}_{{\rm{co}}}={(\frac{\alpha g}{10\Sigma {\mathcal{V}}})}^{1/3}\). Using the literature value21 \(\Sigma =2\,\times 1{0}^{9}\ {{\rm{WK}}}^{-5}{\rm{m}}^{-3}\), the measured volume \({\mathcal{V}}=1.0\, \times 1{0}^{-21}\; {{\rm{m}}}^{3}\) and an educated guess \(\alpha \sim 1{0}^{-4}\), we obtain a predicted \({\rm{NET}}\) versus \(T\). Our simple model above predicts a maximum \({\rm{NET}} \sim\! 60\ \mu {\rm{K}}/\sqrt{{\rm{Hz}}}\) at \(\sim\! 20\) mK. This \({\rm{NET}}\) is within the error bars of the measured signal in Fig. 3a, b at low temperatures. Figure 3b makes a quantitative comparison of the measured sub 50 mK equilibrium noise against the presented model. The solid and dashed red lines indicate \({{\rm{NET}}}_{{\rm{eq}}}=\sqrt{2{k}_{{\rm{B}}}{T}^{2}/{G}_{\mathrm{th}}}\) with and without the photon contribution using the parameters given above, respectively. The shaded area exhibits the impermissible range due to the fundamental temperature noise in equilibrium. We reach this bound at temperatures well below 30 mK. The rest of the lines in this figure will be discussed later.

Fig. 3: Temperature fluctuations in equilibrium.
figure 3

a Measured low-frequency fluctuations \({\rm{NET}}=\sqrt{{S}_{T}}\) at different bath temperatures. The symbols are the measured data (both in a and b) with the mean instrumental background noise subtracted as described in the Methods section. The shaded area covers the uncertainty in this subtraction process. The inset shows schematically the thermal model including the absorber with finite heat capacity \({\mathcal{C}}\) coupled to the heat bath at temperature \(T\) via thermal conductance \({G}_{{\rm{th}}}\). b Comparison of the data to the predicted noise-equivalent temperature NET, now on a logarithmic scale, in the absence (\(\alpha =0\), dashed lines) and presence (\(\alpha =1{0}^{-4}\), solid lines) of photon contribution assuming a normal-metal absorber. The error bars on the experimental points are based on the same uncertainty as in a. Red lines show the fundamental noise-equivalent temperature in equilibrium \({{\rm{NET}}}_{{\rm{eq}}}=\sqrt{2{k}_{{\rm{B}}}{T}^{2}/{G}_{\mathrm{th}}}\), and blue and green lines demonstrate \({\rm{NET}}=\delta \epsilon /\sqrt{\mathcal{C}{G}_{\mathrm{th}}}\), which is the required NET of the detector to observe a photon with energies \(\delta \epsilon =1{\rm{K}}\times {k}_{{\rm{B}}}\) and \(\delta \epsilon =10{\rm{K}}\times {k}_{{\rm{B}}}\), respectively. Then \({\rm{NET}}/{{\rm{NET}}}_{{\rm{eq}}}\) gives the expected signal to noise ratio of the experiment.

The analysis above could be improved, provided the parameters of the system were known precisely. Till now we assumed the absorber to be in the normal state. However, the clean absorber-superconductor contact leads to a proximity induced superconductivity in the absorber. This suppresses the density of states around the Fermi level, on the scale of the Thouless energy \({E}_{{\rm{Th}}}=\hslash D/{\ell}^{2} \sim 10\,\) µeV, resulting in a decreased electron–phonon coupling. Here, \(D \sim 0.01\)\({{\rm{m}}}^{2}/{\rm{s}}\) is the diffusion constant of the Cu film. As a consequence, for electron temperatures below \({E}_{{\rm{Th}}}/{k}_{{\rm{B}}} \sim 100\) mK, the thermal conductance \({G}_{{\rm{th}}}\) is decreased22 and, hence, the temperature noise \({\rm{NET}}\) is increased. The experimentally observed \({\rm{NET}} \sim 80\,{\mathrm{\mu}} {\rm{K}}/\sqrt{{\rm{Hz}}}\) at low \(T\) can then be obtained using \(D=0.01\,{{\rm{m}}}^{2}/{\rm{s}}\) and \(\alpha =1{0}^{-3}\). One should also note that the fluctuations \(\delta T\) of temperature become non-negligible as compared to \(T\) based on the estimate \(\delta T/T\simeq \sqrt{{k}_{{\rm{B}}}/\mathcal{C}}\,\gtrsim\, 0.1\) at \(T=10\) mK for our absorber.

Nonequilibrium fluctuations

Let us finally consider the nonequilibrium fluctuations23,24,25,26. In the measurements presented up to now the injector junction with tunnel resistance \({R}_{{\rm{T}}}=20\) k\(\Omega\) on the left in Fig. 1b has been unbiased in order to ensure equilibrium. By applying a voltage \(V\) to it, the system can be driven into nonequilibrium. The well-known influence of such biasing of a superconductor-normal-metal junction is that it serves as a local refrigerator of the normal-metal absorber thanks to the energy gap of the superconductor, i.e., it acts as an evaporative cooler27. This effect is manifested in the bias dependence of the average temperature of the absorber, obtained from the values of \(\langle {S}_{21}\rangle\) in Fig. 4a.

Fig. 4: Temperature and its fluctuations under nonequilibrium conditions.
figure 4

a Average temperature of the absorber when the injecting junction is biased at different voltages \(V\). The data sets correspond to bath temperatures 12, 27, 35, 43, 52, 67, 83, 100, 117, 135, 166, 198, and 233 mK from bottom to top. b Nonequilibrium temperature fluctuations at temperatures 12, 27, 35, 52, 67, 100, 117, 166 mK with the same colors as in a as a function of injector bias.

Injecting electrons does not only change the average temperature of the absorber but, due to the stochastic nature of tunneling, it leads to noise of heat current as well28,29. Quantitatively this noise at low frequencies is given by

$${S}_{\dot{Q}}^{{\rm{in}}}= \;\frac{1}{{e}^{2}{R}_{{\rm{T}}}}\int dE{(E-eV)}^{2}{n}_{{\rm{S}}}(E)\\ \times\{{f}_{{\rm{N}}}(E-eV)[1-{f}_{{\rm{S}}}(E)]+{f}_{{\rm{S}}}(E)[1-{f}_{{\rm{N}}}(E-eV)]\},$$

where \({f}_{{\rm{N}}},\,{f}_{{\rm{S}}}\) are the energy distribution functions for the normal-metal and superconductor electrons, respectively, and \({n}_{{\rm{S}}}(E)=| E| /\sqrt{{E}^{2}-{\Delta }^{2}}\theta (| E| -\Delta )\) denotes the density of states for the superconductor, with \(\theta (x)\) being the Heaviside step function. For typical voltages and temperatures in the regime well below the superconducting gap, the injection noise \(\sqrt{{S}_{\dot{Q}}^{{\rm{in}}}}\) is exponentially suppressed16. In contrast, the equilibrium noise due to phonons, \(\sqrt{{S}_{\dot{Q}}^{{\rm{eq}}}}\), is of a roughly constant magnitude \(\sim\! 1{0}^{-20}\ {\rm{W}}/\sqrt{{\rm{Hz}}}\). Therefore, it is not surprising that the temperature noise in Fig. 4b does not change much at sub-gap voltages \(V\,<\, 200\,\) µV, in particular as the temperature of the absorber is not changing dramatically in this bias range. For these uncorrelated sources the temperature noise is predicted to obey \({S}_{T}=({S}_{\dot{Q}}^{{\rm{eq}}}+{S}_{\dot{Q}}^{{\rm{in}}})/{G}_{{\rm{th}}}\). The sudden decrease of temperature noise NET at \(V\,> \, 200\) µV is natural since \({G}_{{\rm{th}}}\) increases rapidly when the absorber heats up in this regime (see Fig. 4a). The sharp peak at the gap (Fig. 4b) is possibly an artifact arising from unavoidable voltage noise of the injector, which directly transforms to temperature noise due to the strong voltage dependence of temperature at this point. Yet we find close resemblance of our measured bias-dependent noise and the theoretical predictions by Laakso et al.26 calculated for a SINIS (superconductor-insulator-normal metal-insulator-superconductor) device.


The temperature that fluctuates is given by the energy distribution of the electrons in the absorber. It qualifies as temperature for the following reasons. (i) Number of particles is large, about \(1{0}^{8}\). (ii) Owing to fast electron–electron internal relaxation over a time scale of \(\sim\! 1{0}^{-9}\) s30, the carriers form a local Fermi–Dirac distribution: all other relaxation times, most notably the electron–phonon time (\(\sim\! 1{0}^{-5}\) s) are much slower31. Furthermore, the temperature of the absorber is spatially uniform, since the heat diffusion time of electrons in the absorber, \({\tau }_{{\rm{diff}}}\) = \(\gamma \rho {\ell }^{2}/{{\mathcal{L}}}_{0} \sim 1{0}^{-10}\) s is very short. Here, \(c=\gamma T\) is the specific heat due to conductance electrons with \(\gamma \sim 1{0}^{2}\ {{\rm{Jm}}}^{-3}\ {{\rm{K}}}^{-2}\), \(\rho \sim 1{0}^{-8}\ \Omega\)m is the resistivity of the Cu, and \({{\mathcal{L}}}_{0}=2.44\,\times 1{0}^{-8}\ {\rm{W}}\Omega {{\rm{K}}}^{-2}\) is the Lorenz number.

A central question is the projected energy resolution of the presented calorimeter. The objective is to use it for observing quanta in the microwave regime. Unlike some of the previously published works on THz calorimetry32,33, here we aim into the GHz regime common in circuit QED (quantum electrodynamics) experiments. Here, we demonstrated that its resolution is as good as nature can allow, limited only by thermal fluctuations and illustrated by the red lines in Fig. 3b. Indeed, as we present by the blue lines in the figure, the necessary NET of the detector to observe microwave photons, e.g., those emitted by a standard superconducting qubit with \(0.5-1\,{\rm{K}}\times {k}_{{\rm{B}}}\) energy is well above the fundamental fluctuations at sub 30 mK temperatures.


Background measurements

We measure the instrumental noise dominated by that of the low-temperature Caltech CITLF2 cryogenic SiGe low-noise amplifier \(\langle \delta {S}_{21,{\rm{bg}}}^{2}\rangle\) by carefully off-tuning the interesting fluctuations from the sample itself. This is achieved by simultaneously (i) biasing the thermometer junction away from the ZBA regime (\({V}_{{\rm{th}}}\simeq 85\,\) µV), and (ii) measuring at either below or above the resonance at frequency \({f}_{0}\). An example of the corresponding parametric background noise measurement, in form \(\sqrt{\langle \delta {S}_{21,{\rm{bg}}}^{2}\rangle }\) versus \(\langle {S}_{21}\rangle\) is presented in Fig. 5. We see a typical increase of noise when the attenuation increases towards left. This dependence can be understood quantitatively by assuming constant voltage noise independent of \(\langle {S}_{21}\rangle\). The measured transmission can be written as


where \(v\) is the output of the last stage amplifier, \(\widetilde{v}=\sqrt{50\,{\rm{\Omega }}\times 1\,{\rm{mW}}}\simeq 224\) mV. Noise of \(v\) translates then into variations of \({S}_{21}\) in linear regime as

$$\delta {S}_{21}=\frac{20}{{\rm{ln}}10}\frac{\delta v}{v},$$

and can be written with the help of Eq. (6) for the rms values as

$$\sqrt{\langle \delta {S}_{21,{\rm{bg}}}^{2}\rangle }=\frac{20}{{\rm{ln}}10}\frac{\sqrt{\langle \delta {v}^{2}\rangle }}{\widetilde{v}}1{0}^{-\langle {S}_{21}\rangle /20}.$$

Based on the fit parameter \(a\) in Fig. 5a and the total gain of 60 dB of the amplifier chain, we find the input voltage noise to be \(\sim\! 12\) nV corresponding to the noise temperature of the amplifier of \({T}_{{\rm{n}}} \sim \,5\) K, which is in line with its specifications by the manufacturer.

Fig. 5: Background noise measurements.
figure 5

All the data are taken outside the zero bias regime of the thermometer and at nonresonant frequencies to exclude the actual noise from the sample. The inset of a shows an example of \(\langle {S}_{21}\rangle\) measured around the resonance frequency indicated by the central upward arrow. The blue dots in the main frame of a depict parametric plot \(\sqrt{\langle \delta {S}_{21,{\rm{bg}}}^{2}\rangle }\) versus \(\langle {S}_{21}\rangle\) at the bias voltages \({V}_{{\rm{th}}}=85\,\) µV and at frequencies below the resonance down to 614 MHz indicated by a downward arrow. The red solid line shows the predicted dependence of Eq. (8) yielding the noise temperature of the amplifier of \({T}_{{\rm{n}}}=4.9\) K as the only fit parameter of the curve (constant noise voltage at the input). b The full range measurement of the background as in a but now both above and below the resonance with red and blue dots, respectively. The polynomial fits for the two backgrounds separately (black dashed lines) and the average of them (green solid line) are shown, and they define the mean and the shaded area in Fig. 3. The inset of b is simply the zoom-out of the high attenuation range of the main frame.

Figure 5b presents background measurements at frequencies both below and above the resonance over a wide range of attenuation \(\langle {S}_{21}\rangle\). We observe two features that we need to consider when making an accurate evaluation of the \(\langle \delta {S}_{21,{\rm{bg}}}^{2}\rangle\). First, at large attenuations, due to the fact that the changes are not fully linear in the sense of Eq. (7), the exponential dependence of Eq. (8) is not obeyed strictly. Therefore, we resort to polynomial fits in two regimes, to capture the dependence over the full range. Second, there is a weak dependence of the amplifier noise on frequency; thus the data taken below and above the resonance differ from each other slightly. What we do then, e.g., in Fig. 3, is that we take the mean between the two background measurements as the reference and indicate by the shaded area the uncertainty incurred due to the difference between the two extremes. We thus assume that the frequency dependence of the noise is more or less smooth in the narrow range of \(\sim\! 10\) MHz around \({f}_{0}\), and interpolate the data accordingly.

Experimental details

The sample (Fig. 1b) was fabricated on standard oxidized Si substrate using Ge process for achieving robust deposition mask34,35. The electron-beam lithography was used to pattern the structure for three-angle shadow evaporation of metals. First we deposit 20 nm of Al making the leads followed by oxidation in pure \({O}_{2}\) (1 min at 1 mbar). Next another Al layer of 20 nm thickness again provides the clean superconducting contact at the distance of 50 nm from the thermometer junction, and finally we deposit 35 nm Cu to form the absorber. In the main text we give an estimate of the volume of the absorber based on this thickness; the effective thickness may be somewhat smaller due to the partial oxidation of the film. The resonator is a spiral on a separate chip made of 100 nm thick Al by simple one angle evaporation. The heart of the measuring set-up is shown in Fig. 1b with inductance \(L=100\) nH, \({C}_{1}=10.3\) fF and \({C}_{2}=59.3\) fF as coupling capacitors, and \(C=0.2\) pF. The rest of the RF circuitry follows closely to what is presented in ref. 31. All measurements were performed in a carefully shielded and filtered set-up described in ref. 36.

Data availability

The data and the numerical code that support the plots within this article are available from the corresponding author upon reasonable request.


  1. Johnson, J. B. Thermal agitation of electricity in conductors. Phys. Rev. 32, 97–109 (1928).

    CAS  ADS  Article  Google Scholar 

  2. Nyquist, H. Thermal agitation of electric charge in conductors. Phys. Rev. 32, 110–113 (1928).

    CAS  ADS  Article  Google Scholar 

  3. Lifshitz, E. M. & Pitaevskii, L. P. Statistical physics, Part I (Pergamon, Oxford, 1980).

  4. Kittel, C. Temperature fluctuation: an oxymoron. Phys. Today 41, 93 (1988).

    ADS  Article  Google Scholar 

  5. Mandelbrot, B. B. Temperature fluctuation: a well-defined and unavoidable notion. Phys. Today 42, 71–73 (1989).

    ADS  Article  Google Scholar 

  6. Chui, T. C. P., Swanson, D. R., Adriaans, M. J., Nissen, J. A. & Lipa, J. A. Temperature fluctuations in the canonical ensemble. Phys. Rev. Lett. 69, 3005–3008 (1992).

    CAS  ADS  Article  Google Scholar 

  7. Day, P. et al. The fluctuation-imposed limit for temperature measurement. J. Low Temp. Phys. 107, 359–370 (1997).

    CAS  ADS  Article  Google Scholar 

  8. Vijay, R., Slichter, D. H. & Siddiqi, I. Observation of quantum jumps in a superconducting artificial atom. Phys. Rev. Lett. 106, 110502 (2011).

    CAS  ADS  Article  Google Scholar 

  9. Minev, Z. K. et al. To catch and reverse a quantum jump mid-flight. Nature (2019).

  10. Pekola, J. P., Solinas, P., Shnirman, A. & Averin, D. V. Calorimetric measurement of work in a quantum system. New J. Phys. 15, 115006 (2013).

    ADS  Article  Google Scholar 

  11. Stahle, C. K., McCammon, D. & Irwin, K. D. Quantum calorimetry. Phys. Today 52(8), 32 (1999).

    CAS  Article  Google Scholar 

  12. Govenius, J., Lake, R. E., Tan, K. Y. & Möttönen, M. Detection of Zeptojoule microwave pulses using electrothermal feedback in proximity-induced josephson junctions. Phys. Rev. Lett. 117, 030802 (2016).

    CAS  ADS  Article  Google Scholar 

  13. Kokkoniemi, R. et al. Nanobolometer with ultralow noise equivalent power. Comm. Phys. 2, 124 (2019).

    ADS  Article  Google Scholar 

  14. Kuzmin, L. S. et al. Photon-noise-limited cold-electron bolometer based on strong electron self-cooling for high-performance cosmology missions. Comm. Phys. 2, 104 (2019).

    CAS  ADS  Article  Google Scholar 

  15. van den Berg, T. L., Brange, F. & Samuelsson, P. Energy and temperature fluctuations in the single electron box. New J. Phys. 17, 075012 (2015).

    Article  Google Scholar 

  16. Brange, F., Samuelsson, P., Karimi, B. & Pekola, J. P. Nanoscale quantum calorimetry with electronic temperature fluctuations. Phys. Rev. B 98, 205414 (2018).

    CAS  ADS  Article  Google Scholar 

  17. Karimi, B. & Pekola, J. P. Noninvasive thermometer based on the zero-bias anomaly of a superconducting junction for ultrasensitive calorimetry. Phys. Rev. Appl 10, 054048 (2018).

    CAS  ADS  Article  Google Scholar 

  18. Schmidt, D. R., Schoelkopf, R. J. & Cleland, A. N. Photon-mediated thermal relaxation of electrons in nanostructures. Phys. Rev. Lett. 93, 045901 (2004).

    CAS  ADS  Article  Google Scholar 

  19. Wellstood, F. C., Urbina, C. & Clarke, J. Hot-electron effects in metals. Phys. Rev. B 49, 5942–5955 (1994).

    CAS  ADS  Article  Google Scholar 

  20. Timofeev, A. V., Helle, M., Meschke, M., Möttönen, M. & Pekola, J. P. Electronic refrigeration at the quantum limit. Phys. Rev. Lett. 102, 200801 (2009).

    ADS  Article  Google Scholar 

  21. Wang, L. B., Saira, O. -P., Golubev, D. S. & Pekola, J. P. Crossover between electron-phonon and boundary-resistance limits to thermal relaxation in copper films. Phys. Rev. Appl. 12, 024051 (2019).

    CAS  ADS  Article  Google Scholar 

  22. Heikkilä, T. T. & Giazotto, F. Phase sensitive electron-phonon coupling in a superconducting proximity structure. Phys. Rev. B 79, 094514 (2009).

    ADS  Article  Google Scholar 

  23. Averin, D. V. & Pekola, J. P. Violation of the fluctuation-dissipation theorem in time-dependent mesoscopic heat transport. Phys. Rev. Lett. 104, 220601 (2010).

    ADS  Article  Google Scholar 

  24. Heikkilä, T. T. & Nazarov, Y. V. Statistics of temperature fluctuations in an electron system out of equilibrium. Phys. Rev. Lett. 102, 130605 (2009).

    ADS  Article  Google Scholar 

  25. Ciliberto, S., Imparato, A., Naert, A. & Tanase, M. Heat flux and entropy produced by thermal fluctuations. Phys. Rev. Lett. 110, 180601 (2013).

    CAS  ADS  Article  Google Scholar 

  26. Laakso, M. A., Heikkilä, T. T. & Nazarov, Y. V. Theory of temperature fluctuation statistics in superconductor-normal metal tunnel structures. Phys. Rev B 85, 184521 (2012).

    ADS  Article  Google Scholar 

  27. Nahum, M., Eiles, T. M. & Martinis, J. M. Electronic microrefrigerator based on a normal-insulator-superconductor tunnel junction. Appl. Phys. Lett. 65, 3123 (1994).

    CAS  ADS  Article  Google Scholar 

  28. Golubev, D. & Kuzmin, L. Nonequilibrium theory of a hot-electron bolometer with normal metal-insulator-superconductor tunnel junction. J. Appl. Phys. 6464, 6464 (2001).

    ADS  Article  Google Scholar 

  29. Zhan, F., Denisov, S. & Hänggi, P. Power spectrum of electronic heat current fluctuations. Phys. Status Solidi B 250, 23552364 (2013).

    Article  Google Scholar 

  30. Pothier, H., Gueron, S., Birge, N. O., Esteve, D. & Devoret, M. H. Energy distribution function of quasiparticles in mesoscopic wires. Phys. Rev. Lett. 79, 3490–3493 (1997).

    CAS  ADS  Article  Google Scholar 

  31. Viisanen, K. L. & Pekola, J. P. Anomalous electronic heat capacity of copper nanowires at sub-Kelvin temperatures. Phys. Rev. B 97, 115422 (2018).

    CAS  ADS  Article  Google Scholar 

  32. Nahum, M. & Martinis, J. M. Ultrasensitive-hot-electron microbolometer. Appl. Phys. Lett. 63, 3075 (1993).

    CAS  ADS  Article  Google Scholar 

  33. Wei, J. et al. Ultrasensitive hot-electron nanobolometers for terahertz astrophysics. Nature Nanotechnology 3, 496 (2008).

    CAS  ADS  Article  Google Scholar 

  34. Meschke, M., Kemppinen, A. & Pekola, J. P. Accurate Coulomb blockade thermometry up to 60 kelvin. Phil. Trans. R. Soc. A 374, 20150052 (2015).

    ADS  Article  Google Scholar 

  35. Pashkin, Y., Nakamura, Y. & Tsai, J. -S. Implementation of single-electron transistor with resistive gate. Jpn. J. Appl. Phys. 38, 406–409 (1999).

    CAS  ADS  Article  Google Scholar 

  36. Saira, O. -P. Electrostatic Control of Quasiparticle Transport in Superconducting Hybrid Nanostructures. PhD thesis, Aalto Univ., pp. 41–44 (2013).

Download references


We acknowledge J. T. Peltonen, E. T. Mannila, O.-P. Saira and S. Gasparinetti for technical support, W. Belzig, D. Nikolic, I. Khaymovich, and T. Tuukkanen for discussions and tests of thermometry, and M. Campisi and K. Saito for useful discussions. This work was funded through Academy of Finland grants 297240, 312057 and 303677 and from the European Union’s Horizon 2020 research and innovation program under the European Research Council (ERC) program and Marie Sklodowska-Curie actions (grant agreements 742559 and 766025). F.B and P.S. were supported by the Swedish VR. We acknowledge the facilities and technical support of Otaniemi research infrastructure for Micro and Nanotechnologies (OtaNano).

Author information

Authors and Affiliations



The experiment was proposed by J.P. and its realization was conceived by all the authors. B.K. performed the experiment, and designed and fabricated the samples. Data analysis and modeling were performed by B.K. and J.P., with contributions on the noise analysis by F.B. and P.S. The manuscript was written by B.K. and J.P.

Corresponding authors

Correspondence to Bayan Karimi or Jukka P. Pekola.

Ethics declarations

Competing interests

The authors declare no competing interests.

Additional information

Peer review information Nature Communications thanks Olivier Bourgeois, A. Crepieux, and the other, anonymous, reviewer(s) for their contribution to the peer review of this work. Peer reviewer reports are available.

Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary information

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Karimi, B., Brange, F., Samuelsson, P. et al. Reaching the ultimate energy resolution of a quantum detector. Nat Commun 11, 367 (2020).

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI:

Further reading


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.


Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing