Alkali metal vapors enable access to single electron systems, suitable for demonstrating fundamental light-matter interactions and promising for quantum logic operations, storage and sensing. However, progress is hampered by the need for robust and repeatable control over the atomic vapor density and over the associated optical depth. Until now, a moderate improvement of the optical depth was attainable through bulk heating or laser desorption – both time-consuming techniques. Here, we use plasmonic nanoparticles to convert light into localized thermal energy and to achieve optical depths in warm vapors, corresponding to a ~16 times increase in vapor pressure in less than 20 ms, with possible reload times much shorter than an hour. Our results enable robust and compact light-matter devices, such as efficient quantum memories and photon-photon logic gates, in which strong optical nonlinearities are crucial.
Alkali metal vapors in confined geometries constitute a fertile ground for quantum optical technology1, both as isolated atoms and as coherent ensembles of atoms2. Alkali metal atoms can be viewed as one electron systems, due to the presence of a single electron in the outer shell. The resulting sharp resonances find applications in atom cooling, precision spectroscopy and in the frequency stabilization of lasers on atomic transitions3. Associated Λ-type systems serve as a basis for atomic clocks4,5 and magnetometry (e.g., for cardiograms and encephalograms)6,7,8,9,10, using coherent population trapping (CPT). The CPT effect also leads to electromagnetically induced transparency (EIT). In turn, the sharp variation of refractive index in the narrow frequency region of EIT can slow down light pulses, effectively trapping them in a vapor cell11. Mapping optical quantum states into coherent behaviors of alkali-metal ensembles, for example atomic spin waves, enables quantum memory1,12,13, as required for synchronising single-photon sources and long-range quantum cryptographic networks14.
In alkali-metal atoms, the Rydberg state corresponds to an excitation of the outer shell electron to a state with high principal quantum number n. In such states, the effective dipoles are enlarged by a factor of n2 compared to ground-state atoms. Huge interactions between individual atoms arise, due to overlapping wave functions, and allow controlled entanglement of the atomic ensembles15. Such systems can induce strong nonlinearity even at the single-photon level; absorbing a photon into a Rydberg state causes the energy levels of all the atoms within the ensemble to shift, preventing the absorption of another photon, i.e., the system becomes transparent. This behavior is known as Rydberg blockade and it enables various quantum gates or switches2,16,17,18,19, it has the potential to form quantum logic networks if it can be harnessed in a robust and reliable package. In particular, it allows a system to be transparent to a single photon but absorbing for a photon pair, which is the essence of nonlinearity20,21. In addition, the energy level structure of Rb provides the basis for almost-degenerate two-photon excitation near 780 nm; the resulting off-resonant enhancement boosts nonlinear optical effects such as four-wave mixing22. The latter can yield squeezed states with reduced amplitude or phase uncertainty, giving rise to a nonclassical enhancement of measurement precision in interferometers23,24, (useful for inertial sensors and space-based gravity wave detectors), quantum limited amplifiers25, and quantum delay lines23.
Underlying all these applications is the ability to manipulate the vapor pressure of atomic ensembles within a confined geometry. The resulting optical depth is a key parameter in determining performance metrics such as the strength of the optical nonlinearity2, the efficiency of an alkali-based quantum memory, and the likelihood of exploiting effective photon-photon interactions within the Rydberg blockade volume. In view of the alkali-metal’s reactivity, adsorption to the cell walls typically limits the optical depths achievable. As a passive measure, various optical coatings have been applied to prevent the atoms from reaching the walls and to preserve their quantum states26. Active control of the optical depth is achieved with conventional Light-Induced Atomic Desorption (LIAD)27,28,29. Conventional LIAD proceeds from low-intensity, preferentially blue-ultraviolet illumination, via non-thermal mechanisms30,31,32, or from high-intensity, preferentially infrared illumination, via direct heating/vaporization of alkali-metal structures28. So far, the best control of optical depth was achieved with feedback loops on LIAD in cells29 and hollow-core fibers27,28. However, it is very slow-desorbing atoms take tens of seconds, requiring hours of recovery time and imposing correspondingly long intervals between successive experiments33,34,35.
Here, we report a new coating for alkali-metal vapour containers, based on plasmonic nanoparticles (NPs). Illuminating the coated vapor cells with visible light dispenses Rb atoms >1000 faster than previously reported, in a reproducible manner. We exploit the plasmonic absorption of the NPs to efficiently transduce electromagnetic energy into localized thermal energy. We report on the photothermal behavior of plasmonic gold NPs in the presence of highly reactive alkali vapor that is capable of forming aurides and of disrupting the molecular bonds in the coating. The photothermal process causes desorption of Rb atoms near the NPs, whose small size is also responsible for the fast response time. Contrary to conventional LIAD33, the Rb desorption per photon, as a function of photon energy, does not depend linearly on the photon energy of the incident light; rather it follows the trend of the plasmonic absorption resonance. In addition, the Au NP coating shows no permanent magnetism and therefore does not influence the coherence of the Rb atoms.
Atomic vapor cell coating based on plasmonic nanoparticles
Figure 1a illustrates the crux of our experiment. The inside of a Rb vapor cell was coated with gold nanoparticles, whose surface plasmon resonance (SPR) was excited by illumination from a 532 nm (green) laser. The excited SPR causes increased light absorption by the NPs, which then transduce light energy into heat. The heat causes Rb atoms in the vicinity of the NPs to desorb from the walls and increase the atomic vapor pressure inside the cell. The D2 transition of Rb was probed with a 780 nm laser to measure absorption by mobile Rb atoms. Due to the very small volume of the nanoparticles, the heating process and associated Rb desorption are much faster than previously reported33,34. Hence, rapid increases in the absorption, as well as higher optical depths, are measured in our coated cells.
For our experiments, we prepared four Rb filled vapor cells of identical dimensions, as illustrated by the photograph in Fig. 1b. In order to investigate the effects of the cell coating, first we prepared an uncoated reference cell. Next, a cell was coated with Au NPs, capped with octadecylamine (ODA)35. The ODA molecules serve as linkers between the cell walls and the Au NPs. In order to preserve the atomic state of Rb, in quantum optics technology, the cell walls are often coated with polydimethylsiloxane (PDMS). Consequently, to demonstrate the benefits of our Au NP coating in such technologies, we prepared two more cells: one had only PDMS coating, and the other had both PDMS and ODA-capped Au NPs coating.
The Au NPs diameter was characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM), and UV-visible spectroscopy, see Fig. 1c, d. Figure 1c shows the line profile of an AFM topography (in inset) of a microscope glass slide that was coated with ODA-capped Au NPs. The height of the line profile suggests that the synthesized NPs are 5 nm (±1 nm) in size. This is in good agreement with the extinction spectrum in Fig. 1d. This spectrum was obtained from a dilute solution of the ODA-capped Au NPs in hexane, with the hexane background subtracted. The spectrum shows a clear plasmon resonance centered at 516 nm, which corresponds to NPs of <8 nm diameter. Moreover, Fourier transform analysis of the TEM image in Fig. 1d indicates that the NPs have an average diameter of 5 nm (±2 nm). Gold nanoparticles from the characterized batch are then deposited inside two vapor cells. This size of the obtained nanoparticles is typical for the technology of Amine-caped Au-NPs preparation35,36,37,38.
Figure 1e shows a dark field microscopy from the inside wall of the reference vapor cell (without Au NPs). The experimental configuration for taking the microscope image is presented in the inset. In the micrograph, the pale blue dots correspond to scattering from Rb crystalline particles, condensed on the inside window. By contrast, Fig. 1f shows a similar dark field micrograph from the vapor cell with Au NPs. The latter can be seen as green patches and yellow aggregates. These Rb cells are then placed within the optical setup.
Dramatic increase in vapor pressure upon light illumination
The optical setup used to study the Rb desorption is sketched schematically in Fig. 2. The 780 nm distributed feedback (DFB) laser was externally modulated to scan over the full frequency range of the Doppler-broadened D2 absorption line of Rb. The DFB laser beam was split, deflecting some of the light towards photodiode 1 through an off-the-shelf reference cell filled with Rb in a natural mixture of isotopes. The rest of the beam was guided through the Au NP coated cell and the Rb absorption spectrum was monitored at photo diode 2. For the desorbing illumination, we used four different laser wavelengths: 406 nm, 430 nm, 532 nm, and 655 nm. In all cases, the light was modulated with an electronically controlled shutter. Subsequently, using beam splitter 2, part of the beam was directed to photo diode 3, which recorded the shutter duty cycles. The desorbing laser light was further attenuated using a neutral density filter wheel and it was then coupled into an optical fiber, used to illuminate the vapor cell.
Figure 3 demonstrates that illuminating the nanoparticles, with desorbing laser light, dramatically increases the vapor pressure in the cells; moreover, the process is highly reproducible. Figure 3a shows the Doppler-broadened D2 absorption line of the natural Rb mixture inside the Au NP coated vapor cell (recorded with PD2). Two pronounced dips can be seen, corresponding to the 87Rb (and 85Rb) Fg = 2 (and Fg = 3) transition lines, respectively. The depth of 85Rb Fg = 3 transition line is indicated as δ. The DFB laser frequency is then stabilized at the maximum absorption of the Fg = 3 line, as shown in Fig. 3b. The recorded trace clearly demonstrates the stability of the DFB laser over an entire second. This period is much larger than the desorbing light pulses which, for 532 nm, 31.5 mW/cm2 laser light, were 45 ms in duration. In response, the absorption by Rb vapor inside the cell rapidly increases, as shown in Fig. 3c, where the maximum is reached in ~14 ms. This increase is evidenced by the depth of the Rb absorption line δ0, which is much larger than δ. It should be noted that the fast decrease of the Rb absorption line, here <20 ms, is equally important, for instance in magneto-optical traps39. Indeed, once such a trap is constructed, the remaining free atoms are disruptive and need to be quickly extracted from the vicinity of the trap. In our case, the fast increase/decrease is observed at various desorbing laser wavelengths and is highly reproducible.
In Fig. 3d, we show ten consecutive illuminations of the vapor cell with 31,5 mW/cm2 but at a different desorbing laser wavelength (406 nm). For each desorbing light pulse, a sharp increase δ0 can be seen, on illumination. As the shutter closes, a sharp decrease of light absorption occurs. This behavior is clearly reproducible over all light pulses. Compared to Fig. 3c, the longer duration (7 s) of the light pulses in Fig. 3d allows us to observe the behavior of the Rb vapor in more detail, during illumination. The initial spike in the absorption depth is followed by a gradual decrease, due to the depletion of the Rb atoms in the coating. At the end of the desorbing light pulse, the absorption depth decreases, together with the Rb vapor density, towards the thermal equilibrium. After each illumination, the coating requires time to recover and load with Rb atoms. For each consecutive light pulse, the initial spike in absorption depth diminishes. This is because, over time, the Rb atoms migrate through the cell volume and aggregate in the cold parts of the cell, for example the two stems outside the region illuminated by desorbing light. For the rest of the experiments in this paper, the coating was allowed to recover for 1 h before each illumination with the desorbing light. In a miniaturized cell, this recovery time will be much shorter.
Rb desorption yield and NP extinction
Figure 4 indicates that the Rb desorption is caused by plasmonic heating of the gold nanoparticles. To establish this, we studied the initial rate of Rb desorption vs. the desorbing light intensity at four different wavelengths, as shown in Fig. 4a. For each wavelength there is a linear dependence of desorption rate on intensity; the gradient of the relationship is smallest for 655 nm, i.e., where the Au NPs have low absorption (Fig. 1d) and so generate the least heat. For reference, the uncoated vapor cell shows no measurable increase in δ0 (see star symbols) in the absence of heat generating NPs. Two separate data sets (full and empty symbols) demonstrate that the data are robust.
To further emphasize the role of plasmonic heating, we perform a linear fit to the data in Fig. 4a and estimate the yield (γ) of the desorption process per photon, at each wavelength. The calculation procedure is detailed in the Supporting Information. Figure 4b shows the calculated values of γ, measured in desorbed atoms per photon, as a function of photon energy. For clarity, the four wavelengths in Fig. 4a are represented by symbols of identical shape and color to the ones in Fig. 4b. Because our coating consists of both Au NPs and linker molecules (ODA), it is important to differentiate between their respective effects on the Rb desorption. This can be achieved by comparing our results to those from Octadecyltrichlorosilane (OTS) molecules33, which are very similar to ODA. The OTS data are obtained at 25 °C and are shown as a black line in Fig. 4b, from which it is immediately obvious that the efficiency of the Au NP coating is far superior to that of the OTS coating. Moreover, the desorption efficiency of OTS depends linearly upon photon energy33, whereas this is not the case for our coating. In fact, the shape of our data is reminiscent of the measured extinction spectrum in Fig. 1d, here plotted as function of photon energy as a gray dashed line. It should be noted that the Au NPs spectrum in solution is red-shifted in comparison to that of Au NPs in vacuum40,41. This spectral shift contributes to the difference between the symbols and the gray line.
Combination with conventional polymer coating
To illustrate the advantage of using our Au NPs in potential quantum photonics applications, we applied it in conjunction with PDMS—a standard anti-relaxation coating for these applications. Figure 5 shows the behavior of the Rb absorption line when illuminated for 1 s with a 532 nm laser pulse; data are shown for each of the four cells presented in Fig. 1b. The traces were recorded in a similar fashion to that in Fig. 3c. It is immediately obvious that for this desorbing wavelength, the cell coated with Au NPs and PDMS (green line) undergoes a clear increase in Rb absorption, compared to the PDMS only cell—following a much faster initial increase, δ is doubled after 1 s, i.e., by the end of the light pulse. This result is very significant, given the suboptimal position of the NPs with respect to the PDMS. Indeed, the purpose of our coating is to interact with Rb atoms and the thick PDMS layer effectively acts as a separator. Even better coating performance can therefore be expected from, for instance, dispersing the Au NPs within the PDMS.
The reach of the thermal processes discussed so far is limited by the thermal conductivity of the system. Within the smaller volumes of the plasmonic excitation, Rb desorption can also result from hot electron-induced photodissociation of Rb from the ODA molecules, by transfer of a hot electron into the anti-bonding orbital of the atom42,43,44,45.
Our study is the first to investigate the triple system (Au + Octadecylamine + Alkali atoms), in the steady state and upon excitation of the plasmon resonance. Although ODA-coated-Au nanoparticles are well-known, their properties and stability have never been tested in the presence of highly reactive alkali atoms. There are very good reasons to doubt this stability.
Separately, the (Alkali atom + Amine)46,47, (Alkali atom + Gold)48,49, and (Amine + Gold)35,36,37,38 have all been investigated, for alternative applications. The results show that thermally excited alkali atoms and gold form aurides, whose properties can greatly differ from gold. Moreover, amines form bonds with the alkali atoms, whereby their reactivity significantly decreases, for longer hydrocarbon-tails. In our system, ODA chains on the spherical NP-surface do not form an atom-tight coating. Consequently, Rb atoms can penetrate to the Au bonded amine head and can influence the strength of this bond. Rb can also attach to the tail of the ODA molecule.
To demonstrate the long-term stability of the ODA-Au-NP coating, we compare the case where it is exposed directly to the alkali atom vapor with the case where it is protected by a PDMS layer. PDMS was chosen because of its well-established desorption and anti-relaxation properties. We observe that the unprotected ODA-Au-NPs coating displays excellent stability, presenting no visible changes 20 months after its production.
Our coating can further be optimized, for example using layer-by-layer methods50. Further optimization of Au-NPs density, size, shape, aspect ratio, ordering, and design (core-shell)51 can tailor the plasmonic particles to specific quantum optical applications.
Although bulk gold presents well-established diamagnetism, gold nanoparticles can have curious magnetic properties. Ref. 52 summarizes significant examples and presents a range of possible physical mechanisms for the origin of a permanent magnetic moment in Au NPs. In our experiments, such a magnetic moment would constitute a source of stray magnetic field at the cell wall and may potentially influence the magnetic polarization and coherence of Rb atoms, limiting applications.
We tested our ODA-Au-NPs coating material by measuring the width of the magnetically sensitive Electromagnetically Induced Transparency (EIT) resonance in Hanle-type configuration53,54. Figure 6 shows the experimental setup used to investigate the anti-relaxation properties of the coating. The 780 nm distributed feedback (DFB) laser is tuned over the full frequency range of the Doppler-broadened D2 absorption line of Rb. The DFB laser beam is split, deflecting some of the light towards photodiode 1 through an off-the-shelf reference cell filled with Rb, in a natural mixture of isotopes. The rest of the beam is guided through the Au NP coated cell and the Rb absorption spectrum is monitored at photo diode 2. Next, the laser is frequency stabilized to the maximum absorption of the transition, starting from Fg = 2 hyperfine ground-state. The light polarization is set to circular and the beam diameter is expanded to 10 mm to cover the entire cell diameter. The cell is situated in the center of a pair of Helmholtz coils with diameter of d = 20 cm. In this way, homogeneous magnetic field B is applied orthogonally to the laser beam direction. The amplitude of B is linearly scanned in ranges up to ±1.7 G. The entire setup (and the sample cell) is situated in the center of three pairs of Helmholtz coils (~3 meters in diameter), compensating all 3 Cartesian components of the Earth’s magnetic field. This 3D Helmholtz setup produces highly homogeneous magnetic-field-compensation in the volume of our experimental setup. This volume is free of any ferromagnetic objects to prevent sources of stray magnetic field. The light transmitted through the Rb cell is then focused on PD2 and monitors the cell absorption.
The results show no sign of permanent magnetic moment on the Au NPs—the obtained resonance width is 33.5 times narrower compared to the EIT from uncoated cell. In fact, the resonance is of the same order of magnitude as one of the most established coatings—Octadecyltrichlorosilane (OTS)55. Moreover, our results are in agreement with several reports in the literature56,57,58 stating that the weak N-Au bond in amines-capped Au NPs does not lead to the creation of unpaired spins; the experiments therein detected no permanent magnetic moments.
The question of magnetism in Au NPs is the subject of intense debate. According to Nealon et al.52, “upon looking at all of the literature, one can only be surprised by the obvious lack of reproducibility”. Moreover, the same authors state that “It seems difficult to observe this magnetism with techniques other than SQUID magnetometry”. Within this context, our coatings combined with EIT measurements present a new opportunity to study the magnetism in plasmonic NPs. Whereas no net magnetic moment is observed in the case of ODA capping, other molecules, in particular thiol-based ones, could yield a different result.
In conclusion, we have presented a type of optical coating for alkali-metal vapor containers. Our coating allows fast and reproducible external control of the vapor density and related optical depth, crucial for quantum optics in these confined geometries. In this proof of principle, it was demonstrated that illuminating our coating significantly outperforms conventional LIAD and is compatible with standard polymer coatings used to preserve quantum states of single atoms and coherent ensembles. Further improvements of our coating are possible by tuning particle size, material composition and polymer environment. The coating can find applications in various containers, including optical cells, magneto-optical traps, micro cells, capillaries, and hollow-core optical fibers.
The datasets generated and analyzed during the current study are available in the University of Bath repository, https://doi.org/10.15125/BATH-00529.
Reim, K. F. et al. Towards high-speed optical quantum memories. Nat. Photonics 4, 218–221 (2010).
Lahad, O. & Firstenberg, O. Induced cavities for photonic quantum gates. Phys. Rev. Lett. 119, 113601 (2017).
Millerioux, Y. et al. Towards an accurate frequency standard at/lambda = 778 nm using a laser-diode stabilized on a hyperfine component of the doppler-free two-photon transitions in rubidium. Opt. Commun. 108, 91–96 (1994).
Camparo, J. The rubidium atomic clock and basic research. Phys. Today 60, 33–39 (2007).
Knappe, S. et al. Atomic vapor cells for chip-scale atomic clocks with improved long-term frequency stability. Opt. Lett. 30, 2351 (2005).
Kominis, I. K., Kornack, T. W., Allred, J. C. & Romalis, M. V. A subfemtotesla multichannel atomic magnetometer. Nature 422, 596–599 (2003).
Kawabata, R., Fukuda, K. & Kandori, A. Optimized condition for buffer gas in optical-pumped magnetometer operated at room temperature. Jpn. J. Appl. Phys. 49, 082401 (2010).
Seltzer, S. J. & Romalis, M. V. High-temperature alkali vapor cells with antirelaxation surface coatings. J. Appl. Phys. 106, 114905 (2009).
Grujić, Z. D., Koss, P. A., Bison, G. & Weis, A. A sensitive and accurate atomic magnetometer based on free spin precession. Eur. Phys. J. D. 69, 135 (2015).
Belfi, J. et al. Cesium coherent population trapping magnetometer for cardiosignal detection in an unshielded environment. J. Opt. Soc. Am. B 24, 2357 (2007).
Phillips, D. F., Fleischhauer, A., Mair, A., Walsworth, R. L. & Lukin, M. D. Storage of light in atomic vapor. Phys. Rev. Lett. 86, 783–786 (2001).
Sprague, M. R. et al. Broadband single-photon-level memory in a hollow-core photonic crystal fibre. Nat. Photonics 8, 287–291 (2014).
Hosseini, M., Campbell, G., Sparkes, B. M., Lam, P. K. & Buchler, B. C. Unconditional room-temperature quantum memory. Nat. Phys. 7, 794–798 (2011).
Gisin, N., Ribordy, G., Tittel, W. & Zbinden, H. Quantum cryptography. Rev. Mod. Phys. 74, 145–195 (2002).
Li, L., Dudin, Y. O. & Kuzmich, A. Entanglement between light and an optical atomic excitation. Nature 498, 466–469 (2013).
Baur, S., Tiarks, D., Rempe, G. & Dürr, S. Single-photon switch based on Rydberg blockade. Phys. Rev. Lett. 112, 073901 (2014).
Kübler, H., Shaffer, J. P., Baluktsian, T., Löw, R. & Pfau, T. Coherent excitation of Rydberg atoms in micrometre-sized atomic vapour cells. Nat. Photonics 4, 112–116 (2010).
Dawes, A. M. C. All-optical switching in rubidium vapor. Science 308, 672–674 (2005).
Firstenberg, O. et al. Attractive photons in a quantum nonlinear medium. Nature 502, 71–75 (2013).
Peyronel, T. et al. Quantum nonlinear optics with single photons enabled by strongly interacting atoms. Nature 488, 57–60 (2012).
Kash, M. M. et al. Ultraslow group velocity and enhanced nonlinear optical effects in a coherently driven hot atomic gas. Phys. Rev. Lett. 82, 5229–5232 (1999).
Vernier, A., Franke-Arnold, S., Riis, E. & Arnold, A. S. Enhanced frequency up-conversion in Rb vapor. Opt. Express 18, 17020 (2010).
Marino, A. M., Pooser, R. C., Boyer, V. & Lett, P. D. Tunable delay of Einstein–Podolsky–Rosen entanglement. Nature 457, 859–862 (2009).
Biedermann, G. W. et al. Atom Interferometry in a Warm Vapor. Phys. Rev. Lett. 118, 163601 (2017).
Pooser, R. C., Marino, A. M., Boyer, V., Jones, K. M. & Lett, P. D. Low-noise amplification of a continuous-variable quantum state. Phys. Rev. Lett. 103, 010501 (2009).
Ghosh, S. et al. Low-light-level optical interactions with rubidium vapor in a photonic band-gap fiber. Phys. Rev. Lett. 97, 023603 (2006).
Slepkov, A. D., Bhagwat, A. R., Venkataraman, V., Londero, P. & Gaeta, A. L. Generation of large alkali vapor densities inside bare hollow-core photonic band-gap fibers. Opt. Express 16, 18976 (2008).
Kaczmarek, K. T. et al. Ultrahigh and persistent optical depths of cesium in Kagomé-type hollow-core photonic crystal fibers. Opt. Lett. 40, 5582 (2015).
Bogi, A. et al. Full control of sodium vapor density in siloxane-coated cells using blue LED light-induced atomic desorption. Opt. Lett. 34, 2643 (2009).
Gozzini, A. et al. Light-induced ejection of alkali atoms in polysiloxane coated cells. Nuovo Cim. D. 15, 709–722 (1993).
Xu, J. H., Gozzini, A., Mango, F., Alzetta, G. & Bernheim, R. A. Photoatomic effect: light-induced ejection of Na and Na2 from polydimethylsiloxane surfaces. Phys. Rev. A 54, 3146–3150 (1996).
Yakshinskiy, B. V. & Madey, T. E. Photon-stimulated desorption as a substantial source of sodium in the lunar atmosphere. Nature 400, 642–644 (1999).
Cappello, A. et al. Light induced atomic desorption from dry-film coatings. J. Chem. Phys. 127, 044706 (2007).
Karaulanov, T. et al. Controlling atomic vapor density in paraffin-coated cells using light-induced atomic desorption. Phys. Rev. A 79, 012902 (2009).
Leff, D. V., Brandt, L. & Heath, J. R. Synthesis and characterization of hydrophobic, organically-soluble gold nanocrystals functionalized with primary amines. Langmuir 12, 4723–4730 (1996).
Shen, M., Du, Y., Hua, N. & Yang, P. Microwave irradiation synthesis and self-assembly of alkylamine-stabilized gold nanoparticles. Powder Technol. 162, 64–72 (2006).
Yang, G.-J. et al. Preparation of glassy carbon electrode modified by hydrophobic gold nanoparticles and its application for the determination of ethamsylate in the presence of cetyltrimethylammonium bromide. Sens. Actuators B Chem. 128, 258–265 (2007).
Qu, Q. et al. Open-tubular capillary electrochromatography using a capillary coated with octadecylamine-capped gold nanoparticles. Electrophoresis 29, 901–909 (2008).
Agustsson, S. et al. Enhanced atomic desorption of 209 and 210 francium from organic coating. Sci. Rep. 7, 4207 (2017).
Chang, W.-S. et al. Radiative and nonradiative properties of single plasmonic nanoparticles and their assemblies. Acc. Chem. Res. 45, 1936–1945 (2012).
Link, S. & El-Sayed, M. A. Spectral properties and relaxation dynamics of surface plasmon electronic oscillations in gold and silver nanodots and nanorods. J. Phys. Chem. B 103, 8410–8426 (1999).
Brongersma, M. L., Halas, N. J. & Nordlander, P. Plasmon-induced hot carrier science and technology. Nat. Nanotechnol. 10, 25–34 (2015).
Mukherjee, S. et al. Hot electrons do the impossible: plasmon-induced dissociation of H 2 on Au. Nano Lett. 13, 240–247 (2013).
Boerigter, C., Campana, R., Morabito, M. & Linic, S. Evidence and implications of direct charge excitation as the dominant mechanism in plasmon-mediated photocatalysis. Nat. Commun. 7, 10545 (2016).
Sarina, S., Waclawik, E. R. & Zhu, H. Photocatalysis on supported gold and silver nanoparticles under ultraviolet and visible light irradiation. Green. Chem. 15, 1814 (2013).
Ri, G.-C. et al. First-principles study of ternary graphite compounds cointercalated with alkali atoms (Li, Na, and K) and alkylamines towards alkali ion battery applications. J. Power Sources 324, 758–765 (2016).
Maluangnont, T., Bui, G. T., Huntington, B. A. & Lerner, M. M. Preparation of a homologous series of graphite alkylamine intercalation compounds including an unusual parallel bilayer intercalate arrangement. Chem. Mater. 23, 1091–1095 (2011).
Pelton, A. D. The Cu–Li (Copper-Lithium) system. Bull. Alloy Phase Diagr. 7, 142–144 (1986).
Liu, T. L. Optical properties of RbAu and CsAu. Phys. Rev. B 12, 3008–3012 (1975).
Ward, B. Development, synthesis and characterization of multifunctional nanomaterials. (KU Leuven, Belgium, 2014).
Harris, N., Ford, M. J. & Cortie, M. B. Optimization of plasmonic heating by gold nanospheres and nanoshells. J. Phys. Chem. B 110, 10701–10707 (2006).
Nealon, G. L. et al. Magnetism in gold nanoparticles. Nanoscale 4, 5244 (2012).
Hanle, W. Uber magnetische Beeinflussung der Polarisation der Resonanzfluoreszenz. Z. fur Phys. D. At., Mol. Clust. 18, 5–10 (1991).
Lehmann, J. C. & Cohen-Tannoudji, C. Pompage optique en champ magnetique faible. C. R. Acad. Sci. Paris 258, 4463–4466 (1964).
Hafiz, M. A. et al. Characterization of Cs vapor cell coated with octadecyltrichlorosilane using coherent population trapping spectroscopy. J. Appl. Phys. 117, 184901 (2015).
Pakiari, A. H. & Jamshidi, Z. Nature and strength of M-S bonds (M = Au, Ag, and Cu) in binary alloy gold clusters. J. Phys. Chem. A 114, 9212–9221 (2010).
Crespo, P. et al. Permanent magnetism, magnetic anisotropy, and hysteresis of thiol-capped gold nanoparticles. Phys. Rev. Lett. 93, 087204 (2004).
Guerrero, E. et al. Surface plasmon resonance and magnetism of thiol-capped gold nanoparticles. Nanotechnology 19, 175701 (2008).
The authors thank Josh Nunn for useful discussion. D.S. is indebted to Anguel Brankov, Nikolaj Baynov, Gueorgui Todorov, Zahari Peshev and Peter Petrov for support with experimental equipment and facilities. V.K.V. acknowledges support from the Royal Society through the University Research Fellowships and through Grant Nos. CHG/R1/170067, PEF1/170015, and RGF/EA/180228, as well as from the STFC Grant No. ST/R005842/1. This work was supported by the EPSRC UK Quantum Technology Hub “Networked Quantum Information Technologies” (EP/M013243/1) through the partnership project “Plasmon-enhanced alkali-metal vapours in hollow-core fibre”. VKV and DS acknowledge the support of COST Action MP1403: Nanoscale Quantum Optics.
The authors declare no competing interests.
Journal peer review information: Nature Communications thanks Mikhail Balabas and other anonymous reviewer(s) for their contribution to the peer review of this work.
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
About this article
Cite this article
Rusimova, K.R., Slavov, D., Pradaux-Caggiano, F. et al. Atomic dispensers for thermoplasmonic control of alkali vapor pressure in quantum optical applications. Nat Commun 10, 2328 (2019). https://doi.org/10.1038/s41467-019-10158-4
Assembly-induced microwave band resonance in gold nanoparticles-based ultrathin and flexible spoof localized surface Plasmon
Materials & Design (2021)
Advanced Optical Materials (2020)