Abstract
Direct removal of 99TcO4− from the highly acidic solution of used nuclear fuel is highly beneficial for the recovery of uranium and plutonium and more importantly aids in the elimination of 99Tc discharge into the environment. However, this task represents a huge challenge given the combined extreme conditions of super acidity, high ionic strength, and strong radiation field. Here we overcome this challenge using a cationic polymeric network with significant TcO4− uptake capabilities in four aspects: the fastest sorption kinetics, the highest sorption capacity, the most promising uptake performance from highly acidic solutions, and excellent radiation-resistance and hydrolytic stability among all anion sorbent materials reported. In addition, this material is fully recyclable for multiple sorption/desorption trials, making it extremely attractive for waste partitioning and emergency remediation. The excellent TcO4− uptake capability is elucidated by X-ray absorption spectroscopy, solid-state NMR measurement, and density functional theory analysis on anion coordination and bonding.
Similar content being viewed by others
Introduction
Uranium/plutonium fission-based nuclear energy is currently one of the most optimal choices for the partial replacement of fossil fuel energy, but faces several key hurdles for further development1,2,3,4. For instance, searching for efficient, reliable, and economically effective strategies for used fuel reprocessing and waste disposal are still in the stage of scientific and technological exploration. Nuclear safety is another concern because several nuclear accidents have occurred in the past several decades and the resulting contamination of tremendous amounts of radioisotopes with combined radiotoxicity and chemotoxicity in the environment is a severe issue. Among them, technetium-99 (99Tc) is a β-emitting radionuclide with a long half-life of 2.13 × 105 years and can be produced in high fission yield (~6%) in a typical uranium fission reactor leading to a large inventory in used nuclear fuel and waste5. It predominately exists in the nuclear fuel cycle and in the environment as the pertechnetate anion (TcO4−), which exhibits high solubility and a nearly non-complexing nature, giving rise to its high environmental mobility with transportation velocity being almost identical as that of groundwater5,6. Tc(VII) complexes are volatile during nuclear waste vitrification process, producing problems for the off-gas system design7. Another serious issue associated with this radioisotope is its capability to greatly interface with the solvent extraction/back extraction process of uranium, neptunium, and plutonium through catalytic redox reactions, generating a notable barrier on the valence state control of these key components in the fuel cycle8,9. Therefore, it would be ideal that TcO4− can be separated at the first stage once used nuclear fuel rods are dissolved in highly concentrated nitric acid solutions even before the plutonium uranium redox extraction (PUREX) process. This is further beneficial because this would eliminate 99Tc discharge into the environment during subsequent waste managing processes. However, this task represents a huge challenge given the combined extreme condition of super acidity (e.g., 3 M nitric acid), high ionic strength (large excess of competing anions), and strong ionizing radiation field (β, γ, and neutron irradiations, etc.).
Although there has been a tremendous amount of effort being paid to designing high-performance anion-exchange materials tailored for the application of TcO4− uptake10, combined features of ultrastability in acids, decent radiation-resistance, high TcO4− uptake kinetics/capacity, and excellent sorption selectivity that are required for the aforementioned task have never been integrated into a single material. For example, traditional commercialized polymeric anion-exchange resins exhibit efficient removal of TcO4− even in acidic conditions11,12,13, but are not radiation-resistant. This clear drawback is greatly amplified given their anion-exchange kinetics are generally quite slow, leading to significant radiation dose received during the long sorption time and subsequent radiation-induced damage of the materials. Purely inorganic cationic materials, such as layered double hydroxides (LDHs)14,15, layered rare-earth hydroxides (LRHs)16, and thorium borates (NDTB-1)17,18, may possess enhanced radiation-resistance, but their relatively low sorption capacity and poor selectivity toward TcO4− impedes real applications. Recently, cationic metal–organic frameworks (MOFs) built from transition metal cations and neutral soft ligands with exchangeable anions in the pores are promising candidates to sequester TcO4−from aqueous solution19,20,21,22, because they display fast sorption kinetics, high capacity, excellent selectivity, and great radiation-resistance. However, none of these materials survives in highly acidic conditions. Therefore, these materials may exhibit potentials in environmental remediation at relatively neutral pHs, but certainly not in fuel reprocessing processes.
Polymeric networks built by repeating organic building blocks have been intensively investigated recently in the area of environmental pollution remediation23,24,25,26,27,28,29,30. They are endowed with a series of excellent features similar with MOFs including predictable reticular synthesis and structure type, controllable pore size/shape/charge, and facile functionalization tailored for trapping targeted environmental pollutants31,32,33,34,35,36,37. More importantly, these materials exhibit superior hydrolytic stability even in highly acidic/basic solutions38,39,40, a clear advantage not possessed by the majority of MOFs. In addition, polymeric network equipped with relatively large conjugated fragments in the structure may also show enhanced radiation-resistance compared to traditional polymeric anion-exchange resins because they can effectively stabilize radiation-induced radical intermediates, another merit critical for nuclear-related applications, especially used fuel reprocessing. Here we report a cationic polymeric network (CPN), SCU-CPN-1 (SCU = Soochow University), which substantially overcomes the long-term challenge of TcO4− separation under the extreme conditions of super acidity, strong irradiation field, and high ionic strength.
Results
Characterization
SCU-CPN-1-Br was derived from the quaternization reaction between 1,1,2,2-tetrakis(4-(imidazolyl-4-yl)phenyl)ethene (TIPE) and 1,4-bis(bromomethyl)benzene (BBB) (Fig. 1a). The degree of cross-linking can be quantified by the ReO4− sorption capacity and the Br− residual after anion-exchange discussed later. SEM (Fig. 1b) images show a uniform spherical morphology with a diameter of ~2 μm. PXRD measurement confirms the amorphous nature of this material (Supplementary Fig. 1), which is similar to many other CPN materials reported41,42. The structure of SCU-CPN-1-Br can be best described as a cationic polymeric network consisting of TIPE and BBB moieties with exchangeable Br− filled in the pores, supported from combined EDS, FT-IR, and solid-state NMR studies. In the FT-IR spectrum, the characteristic peaks of 1074 cm−1 correspond to the quaternary imidazolium species (Supplementary Fig. 2)43. The characteristic peaks at 53.9, 123, 133.9, and 142.9 ppm in the solid-state 13C NMR spectrum of SUC-CPN-1 (Fig. 2) can be ascribed to the sp3-hybridized carbon atoms of methylene, ethylene, sp2-hybridized carbon atoms on benzene rings, and the carbon atoms bound to the nitrogen atom, respectively. Thermogravimetric analysis shows that SCU-CPN-1-Br is stable up to 300 °C (Supplementary Fig. 3). The initial weight loss below 150 °C corresponds to the removal of water and N,N-dimethyl formamide (DMF) molecules. The N2 sorption isotherm measured at 77 K does not yield any noticeable uptake amount, initially suggesting a non-porous structure of SCU-CPN-1, likely because the charge-balancing anions effectively block the transportation pathway of the gas molecule. However, this is not the case for the anion-exchange process demonstrated below.
Sorption kinetics analysis
Before anion-exchange studies, SCU-CPN-1-Br was immersed into saturated NaCl solutions to replace toxic Br− with Cl− (SCU-CPN-1). The anion-exchange process was confirmed by TEM-EDS mapping (Fig. 1c) and SEM-EDS (Supplementary Fig. 4) analysis. The Br− residual after anion-exchange is due to the incomplete quaternization reaction in the material synthesis, because Cl− can be fully exchanged with ReO4− (see discussion below). This residue amount can be therefore used for calculation of degree of cross-linking to be 96.9 ± 0.2%. SCU-CPN-1 also facilitates the complete exchange with NO3− (SCU-CPN-1-NO3) (Supplementary Fig. 5), which is beneficial on used fuel repossessing applications because Cl− is often not desired in these processes given its redox property toward several actinides. It should be noted that the anion-exchange properties of SCU-CPN-1-Cl and SCU-CPN-1-NO3 samples are almost identical.
TcO4− uptake experiments were initially performed by contacting 10 mg samples of SCU-CPN-1 with a 10 ml aqueous solution containing 28 ppm 99TcO4−. The concentration of TcO4−in aqueous solution was monitored by its characteristic absorption feature at 290 nm in the UV–vis spectra (Fig. 3a), as well as liquid scintillation counting measurements (Fig. 3b). SCU-CPN-1 shows a surprisingly high removal rate for TcO4− from aqueous solution. Instantly after the contact (<30 s, which is in fact required for the experimental operation), the characteristic peak of TcO4− in the spectrum completely disappeared, representing the fastest TcO4− sorption kinetics and shortest equilibrium time that has ever been reported for an anion-exchange material (Supplementary Table 1). The desorption of Cl− into the solution was monitored by ion chromatograph to be as rapid as the TcO4−/ReO4− uptake (Supplementary Fig. 6a), supporting the anion-exchange mechanism. The sorption kinetics of TcO4− by Purolite A532E and A530E (Fig. 3b), which are regarded as standard commercial anion-exchange resins for efficiently removing TcO4− from aqueous solution, were also tested under identical sorption conditions. In sharp contrast, SCU-CPN-1 removes more than 99% of TcO4− from aqueous solution in less than 30 s, whereas Purolite A532E and A530E resins take at least 120 min to reach their sorption equilibrium and uptake only 32% and 38% of TcO4− in 5 min, respectively. A further sorption experiment using Purolite A530E with a smaller particle size (<100 μm, denoted as Purolite A530E-ground) shows a much enhanced sorption kinetics, where the sorption equilibrium time is reduced to 5 min (Supplementary Fig. 6b). This suggests the small particle size of SCU-CPN-1 should be a major origin for the faster exchange kinetics observed. Although SCU-CPN-1 is non-porous for N2 uptake, it seems to be porous enough for rapid anion transportation during the exchange process. Comparison of crystalline cationic MOFs with ordered pore channels further highlights the advanced TcO4− removal rate that SCU-CPN-1 exhibits. For example, the two most optimal cationic MOFs, SCU-100 and SCU-101 reported recently, take 30 and 10 min to reach their sorption equilibrium, respectively19,21. Such an advantage would be further beneficial by decreasing the radiation dose received during highly radioactive waste management. This also provides an extremely attractive emergency response material for efficiently controlling the accidental release of 99Tc into the environment, where the sorption rate is the most critical parameter. In order to analyze the sorption mechanism of SCU-CPN-1 in detail, we have investigated the sorption kinetics again by lowering the sorbent loading and ReO4−concentration (Supplementary Fig. 6c), showing a pseudo-second order reaction process (Supplementary Table 2). Under this condition, SCU-CPN-1 still performs much better than Purolite A530E-ground. SCU-CPN-1 reaches the sorption equilibrium in 10 min whereas it takes at least 140 min to reach the sorption equilibrium for Purolite A532E-ground. The rate constant of SCU-CPN-1 is much larger than that of Purolite A530E-ground. Additionally, the distribution coefficient (Kd) of SCU-CPN-1 toward ReO4− reaches as high as 6.2 × 105 ml g−1, which is comparable to the highest reported value (Supplementary Table 3), showing promises in the removal depth for the environmental remediation applications.
Sorption isotherm analysis
We further evaluated the sorption capacity of SCU-CPN-1 toward TcO4−. Due to the limited amount of 99Tc available, as well as the regulation on the amount of radioactive materials that can be handled, ReO4− was used as a surrogate for TcO4− given their almost identical charge densities and therefore chemical behaviors44. In fact, this was further confirmed based on the sorption kinetics data under the same sorption conditions (Fig. 3b). From the sorption isotherm curve (Fig. 4a), the saturated sorption capacity calculated from fitting based on Langmuir model (see details in SI) is 876 mg ReO4− g−1 SCU-CPN-1 material (Supplementary Table 4). When a small excess of ReO4− is present in solution, almost 100% of Cl− anions in SCU-CPN-1 can be quantitatively replaced by ReO4−, as determined from ICP analysis of ReO4− sorbed samples, giving a notably large exchange capacity of 999 ± 20 mg ReO4− g−1 SCU-CPN-1 material (Supplementary Table 5), being very close to the theoretic sorption capacity of 1058 mg g−1 calculated by assuming the complete anion-exchange. This capacity is significantly larger than those of Purolite A532E (446 mg g−1) and A530E (706 mg g−1). As a comprehensive comparison, we summarize the TcO4−/ReO4− sorbent materials into five different categories (Fig. 4b and Supplementary Table 6): (1) purely inorganic materials14,17,18,45,46,47,48, (2) composites49,50,51, (3) resins13,52,53,54,55, (4) MOFs19,20,21,22,56,57,58, and (5) CPNs30. Purely inorganic materials and composites exhibit the lowest sorption capabilities toward ReO4−, with maximum capacities reaching 130 and 141 mg g−1, respectively. The cationic MOF materials hold the maximum sorption capacity of 714 mg g−1, which is close to commercial anion-exchange resins. Banerjee et al30. reported a functionalized porous aromatic framework PAF-1-F with a ReO4− sorption capacity of 420 mg g−1. In this work, SCU-CPN-1 sets a new capacity record for removing TcO4−/ReO4−.
Stability under extreme conditions
More importantly, SCU-CPN-1 exhibits outstanding resistance toward high-energy ionizing radiation, including β-rays and γ-rays, providing a substantial prerequisite for application in used nuclear fuel reprocessing and waste management. The radiation-resistance is confirmed by SEM (Supplementary Fig. 7b, c), FT-IR spectra (Fig. 5a), sorption kinetics (Fig. 5b), and sorption capacity (Fig. 5c, d) measurements on the irradiated samples. Very impressively, the microsphere morphology, sorption rate and capacity for ReO4− by SCU-CPN-1 remains unaffected by either radiation type, even after irradiation with extremely large doses of 1000 kGy of β-rays and γ-ray. In comparison, the sorption capacities of ReO4− by Purolite A532E and A530E gradually decrease as the irradiation dose increases, consistent with the literature reports59. After receiving 1000 kGy of either β-rays or γ-rays, the sorption capacities exhibit an ~30% reduction for both resins (Fig. 5c, d), implying poor performance for treating used fuel solutions. This obvious difference originates from the conjugated-ring-rich nature of SCU-CPN-1 and more specifically that the key functional groups of cationic imidazolium are protected within a large conjugated system, while the quaternary ammonium salts in resin materials are easily subject to radiation-induced degradation.
Furthermore, the ReO4− uptake capacity of SCU-CPN-1 remains almost unchanged over a wide pH range from 2 to 12 (Fig. 6a), initially indicating a good uptake selectivity and hydrolytic stability. The morphology and the characteristic peak of SCU-CNP-1 (1074 cm−1) in the FT-IR spectrum remain unchanged after being immersed in 3 M HNO3 solution for 12 h (Supplementary Fig. 8), consistent with the proposed acidic stability, which can be further confirmed by the material regeneration test discussed below.
Uptake selectivity
In highly radioactive wastes, a large excess of competing anions, such as NO3− and SO42−, often coexist with TcO4−. NO3− is present in the highly acidic solution (e.g., 3 M HNO3) of used fuel and SO42− is often included in the high-level liquid waste. We therefore measured the sorption properties of ReO4− by SCU-CPN-1 as a function of NO3− and SO42− concentration. The results show that the removal of ReO4− occurs at 91% when the molar ratio of NO3− and ReO4− is as high as 100:1 (Fig. 6d). We further prepared a 3 M HNO3 solution containing 343 ppm of ReO4− (NO3−:ReO4− molar ratio = 2186). It should be noted that there is no reported material that can remove ReO4−/TcO4− under this condition. Impressively, SCU-CPN-1 can extract approximately 40% of ReO4− at a solid/liquid ratio of 20. When the solid/liquid ratio was increased to 90 (a number that is relevant to the chromatographic column application), SCU-CPN-1 is able to remove 76% of available ReO4− from solution (Fig. 6b). This feature clearly represents a priority in uptake for ReO4−/TcO4− over NO3−, and attains to one of the most crucial aspects for removing TcO4− from reprocessed used fuel prior to PUREX. Note this is unattainable for any of the cationic MOFs or purely inorganic materials, which are either instable or completely lose their uptake capability under highly acidic condition. Moreover, with the coexistence of a large excess of SO42− with a much higher charge density, SCU-CPN-1 still extracts 85% and 64% of available ReO4− when the SO42−:ReO4− molar ratio are 100:1 and 6000:1, respectively (Fig. 6c). This excellent selectivity is surprising because high-charge anions often outcompete with low-charge anions during the anion-exchange process given their stronger electrostatic interaction with the host materials18,30. Likely, it can be ascribed to the hydrophobic nature of the pores that possess a higher affinity for those anions with lower charge densities, similar with traditional anion-exchange resins and cationic MOF systems19,20,21,22.
Removal from simulated nuclear wastes
Because critical assessment of the sorption kinetics and radiation stability revealed several superior features combined into one material, the next logical step was to test the capabilities that SCU-CPN-1 has when separating TcO4− in simulated nuclear waste solutions. In the Hanford LAW stream (Supplementary Table 7), the amounts of NO3−, NO2−, and Cl− far exceed that of TcO4− by more than 300 times. Following similar experimental conditions as we have used earlier, SCU-CPN-1 was found to sequester almost 90% of available TcO4− from the waste in a solid/liquid ratio of 5 (Supplementary Table 8), which is notably better than the removal using SCU-101 (75.2% at a solid/liquid ratio of 10) and NDTB-1 (13% at a solid/liquid ratio of 5) that have been previously studied17,18,19.
Material recyclability
SCU-CPN-1 is also a completely reversible anion-exchange material and the microsphere morphology remains unchanged after anion-exchange (Supplementary Fig. 7a), making it very cost-effective for separation applications. More than 97% of initially sorbed ReO4− in SCU-CPN-1 could be exchanged with Cl− or NO3− in 1 M NaCl or NaNO3 solutions heated at 80 °C. (Supplementary Table 9). The elevated temperature required for the complete desorption also indicates a strong interaction between SCU-CPN-1 and TcO4−/ReO4−, which is responsible for the excellent TcO4− uptake capability, especially the selectivity. Even after five sorption/desorption cycles, SCU-CPN-1 remains stable and the sorption properties are not influenced (Fig. 6e). More impressively, under the condition of 3 M HNO3, SCU-CPN-1 remains reusable and the sorption properties are unaffected after at least four runs (Fig. 6f), indicating this material is amazingly stable and fully recyclable under the real used fuel repossessing condition.
Sorption mechanism
The anion-exchange process was further confirmed by TEM-EDS (Fig. 1c) and supported by the evolution of a new peak at 896 cm−1 (Re–O ν3 asymmetric stretch) in the FT-IR spectra after anion-exchange with ReO4− (Fig. 7a). In the solid-state 13C NMR spectrum of SCU-CPN-1-Re, the peak feature for carbon atoms bound to the nitrogen atom shifts from 142.9 to 144.1 ppm after ReO4− uptake, while other signals remained unchanged. This result hints for the interaction between ReO4− with the cationic imidazole group in SCU-CPN-1 (Fig. 7b), further confirmed by the theoretical study discussed below. In addition, extended X-ray absorption fine structure (EXAFS) were carried out to investigate the local environment of ReO4− in SCU-CPN-1. The EXAFS spectrum of SCU-CPN-1-Re sample consists of a Re–O shell at a bond distance (R) of 1.73 Å with a coordination number (N) of 4.1 (Fig. 7d and Supplementary Table 10), very similar to those of the reference sample, NaReO4 (R = 1.74 Å, N = 4)60. This indicates that the Re species in SCU-CPN-1-Re exist as perrhenate, keeping the oxidation state of Re(VII), consistent with the XPS analysis result (Fig. 7c).
To unravel the intrinsic driving force for the superior TcO4− separation capabilities by SCU-CPN-1, we performed DFT theoretical studies aimed at analyzing the interaction between the repeating unit as a fragment of SCU-CPN-1 and TcO4−/ReO4−. We also made a comparison with the case of NO3− in order to elucidate the origin of uptake selectivity and the surprising TcO4−/ReO4− removal capability from highly acidic conditions. The framework of our synthetic SCU-CPN-1 material possesses large positive charges since each N3 atom of the imidazole ring should formally be +1 charged when connecting a methylene. DFT calculations on a local fragment of the material, M+ ([C6H5–C3N2H3–CH2–C6H5]+ fragment), show that the positive ESP (blue areas) mainly distributes on the vdW surface and delocalizes on the imidazole ring, propagating on the N1, C2, N3 atoms and three bounded H atoms, as shown in Fig. 8a. The C4 and C5 atoms do not contribute obviously to the positive ESP. In contrast, ESP distributed on the vdW surfaces of all anions are negative (red areas). Therefore, the local imidazole ring of the material should have a crucial role for attracting these anions by strong electrostatic interaction. Figure 8b shows the stable sorption structures of M+ReO4− (M+TcO4−) and M+NO3−. It can be seen that one side of the ReO4−(TcO4−) tetrahedron, consisting of three oxygen atoms, is almost parallel to the imidazole ring, forming a face-to-face stacking structure. However, NO3− (as well as Cl−) is more inclined to be close to the C2 atom, creating a corner-to-corner interaction. The two distinctly different structures result in the binding energies in M+ReO4− (-8.63 kcal mol−1) and M+TcO4− (−8.91 kcal mol−1), being higher than twice of that for M+NO3− (−4.17 kcal mol−1).
The different sorption structure between M+ReO4−(M+TcO4−) and M+NO3− can be further understood by investigating their electronic structures. As discussed above, the C1, N2, and C3 atoms attract one O atom of the anions through strong electrostatic interactions. Furthermore, molecular orbital analyses show that the N1–C2–N3 π bond hybridize with the p lone pair electrons of ReO4− (Fig. 9a), forming relatively strong p-π interactions that leads to the face-to-face stacking M+ReO4− structure. Meanwhile, although the C4 and C5 atoms of the imidazole ring do not contribute to the positive ESP, the C4–C5 π bond could also hybridize with the p lone pair electrons of another O atom of ReO4− simultaneously (Fig. 9a). In contrast, for NO3− (as well as Cl−), the p lone pair electrons of only one O atom can hybridize with the N1–C2–N3 π bond of the of the imidazole ring (Fig. 9b). These results suggest cationic imidazole ring is the key functional group for the selective uptake of TcO4−/ReO4− over NO3−, which should be further considered for anion-exchange material design in the future.
Discussion
In conclusion, we document here our very recent discovery on the significant TcO4− separation capabilities of a cationic polymeric network material (SCU-CPN-1). SCU-CPN-1 has the potential to be applied in many areas, including used nuclear fuel reprocessing prior to PUREX separations, nuclear waste management ahead of vitrification, remediation of 99Tc contamination in the environment, and emergency response in the event of a nuclear accident. Not only does SCU-CPN-1 set new records for TcO4−/ReO4− uptake kinetics and sorption capacity, but it also exhibits excellent uptake performances from highly acidic solutions even in the presence of large excesses of other competing anions. The decent radiation-resistance observed in this material, which is atypical for traditional anion-exchange resins, coupled with the ability to be proficiently recycled make these potential applications more practical and cost-effective. Furthermore, the NO3− exchanged version of SCU-CPN-1 is fully combustible, meeting the CHON-only standard. Such a synthetic and design strategy can be certainly expanded for the separation of actinides (U, Np, Pu, Am, etc.) and other types of fission products. The foregoing results demonstrate that the family of CPN materials show powerful application potentials in the nuclear industry and their utilities may be realized in the near future.
Methods
Safety note
Caution! Although Tc-99 is a low-energy β-emitter (t1/2 = 2.13 × 105 a), it still possesses significant health risks when inhaled or digested. Standard precautions and procedures for handling radioactive materials should be followed, and all Tc-99 studies were conducted in a licensed laboratory dedicated to radiological investigations.
Chemicals and reagents
1,1,2,2-tetrakis(4-(imidazolyl-4-yl)phenyl)ethene (TIPE) and 1,4-bis(bromomethyl)benzene (BBB) were provided by Beijing HWRK Chem Co., LTD and J&K Scientific LTD, respectively. Commercial anion-exchange resins, Purolite A530E and A532E, were provided from Purolite Co., Ltd, and dried at 60 °C for 24 h before use. NaReO4, HCl, NaOH, and other reagents were analytically pure and used as received. 99TcO4− stock solutions were prepared by dissolving desired amounts of NH4TcO4 (99%) solid in deionized water.
Physical property measurements
A Thermo Nicolet iS50 spectrometer was used to collect the FT-IR spectra in the range of 4000–400 cm−1. Powder X-ray diffraction (PXRD) patterns were collected from 5° to 50° on a Bruker D8 Advance diffractometer equipped with Cu Kα radiation (λ = 1.54056 Å) and a Lynxeye one-dimensional detector. Thermogravimetric analysis was carried out in the range of 30−600 °C under a nitrogen flow with a heating rate of 10 °C min−1 on a NETZSCH STA 449F3 instrument. SEM and energy-dispersive spectroscopy (EDS) images were acquired with the energy of the electron beam being 20 keV using a FEI Quanta 200FEG scanning electron microscope (SEM). The morphology and elemental mapping were recorded by a FEI Tecnai G2 field emission high-resolution transmission electron microscope (HRTEM) with an accelerating voltage of 200 kV. The solid-state 13C NMR spectroscopy was performed on a Bruker Avance III 400 HD instrument with a Larmor frequency of 100.65 MHz. The concentrations of TcO4− in solution were measured using a UV–vis spectrometer (Varian Cary 6000i) by monitoring the characteristic absorption peak at 290 nm and the activity of 99TcO4− was also analyzed by a liquid scintillation counting (LSC) system (Perkin Elmer Quantulus 1220). The concentrations of ReO4− in solution were measured by inductively coupled plasma-atomic emission spectrometry (ICP-AES, Thermo Fisher Scientific iCAP 7000). The concentrations of Cl− in solution as the function of sorption time were evaluated by a 930 Compact IC Flex ion chromatograph instrument (Metrohm, Switzerland). Rhenium LIII-edge EXAFS spectra were collected at the Shanghai Synchrotron Radiation Facility (SSRF, BL14W, Shanghai, China) using a silicon (111) double-crystal monochromator in fluorescence mode. The analyses and fitting of the EXAFS data were performed using the Athena and Artemis packages of the IFEFFIT 7.0 software. The surface state and electronic structure of the material were obtained by X-ray photoelectron spectroscopy (XPS) measurement (SPECS Corporation), equipped with a monochromator delivering Al Kα radiation (1486.7 eV) as the excitation source. The Re 4f XPS spectra of SCU-CPN-Re fitting was carried out via Casa XPS software and the energy scale of the high-resolution spectra were calibrated by C1s peak at 284.8 eV.
Synthesis of SCU-CPN-1
Overall, 0.134 g (0.225 mmol) of TIPE and 0.119 g (0.45 mmol) of BBB were added to 16 ml N,N-dimethyl formamide (DMF) in a 35 ml microwave tube (9.0 cm long cylindrical glass tube with the inside diameter of 2.5 cm and the external diameter of 3 cm). The resulting mixture was stirred at 100 °C for 4 h under the pressure of 150 psi and 150 W of power on a microwave synthesis system (CEM DISCOVER S). SCU-CPN-1-Br powders were obtained after centrifugation, then washed three times with DMF, ethanol, and deionized water each, followed by freeze-drying. After soaking the SCU-CPN-1-Br in saturated sodium chloride (NaCl) solution for 12 h, a yellow powder of SCU-CPN-1-Cl was obtained (yield: 61%).
Batch experiments
All the experiments were conducted at 25 °C using the batch sorption method. The pH was adjusted to the desired value with NaOH and/or HNO3 solutions in 5 min. In a typical batch experiment, 10 mg of SCU-CPN-1 was placed into 10 ml of aqueous solution containing various concentrations of ReO4−/TcO4−. After being stirred at a rate of 120 rpm for a desired contact time, the samples were separated with a 0.22 μm nylon membrane filter (SANJIA Biochemical Supplies).
Sorption kinetics study
The experiments were carried out at pH 7 with a solid/liquid ratio of 1 g l−1. In each sample, 10 mg of sorbent material (SCU-CPN-1, Purolite A530E, or A532E) was added to 10 ml of aqueous solution containing 28 ppm TcO4−. The samples were collected after stirring the mixture at a rate of 120 rpm for 30 s, 3 min, 10 min, 30 min, 60 min, and 90 min, respectively. As a comparison, the uptake kinetics experiment was then repeated by using the same molar amount of ReO4− as the surrogate for TcO4−. Besides, the concentration of Cl− during the ion exchange process was measured as a function of time by ion chromatograph method. In order to evaluate the influence of the particle size in sorption kinetics analysis, the Purolite A530E was ground in an agate mortar and filtered using a 0.106 mm sieve and the particle size was further characterized by SEM image (Supplementary Fig. 9). The sorption kinetics of ground version of Purolite A530E was analyzed under the same uptake condition.
In order to study the sorption mechanism of SCU-CPN-1, 25 mg of SCU-CPN-1 was added to 500 ml of aqueous solution containing 14 ppm ReO4−. 1 ml of samples were taken after stirring the mixture at a rate of 120 rpm for 30 s, 1 min, 2 min, 3 min, 4 min, 5 min, 7.5 min, 10 min, 15 min, 30 min, 60 min, 90 min, and 110 min, respectively. The samples were separated using a 0.22 µm nylon membrane filter for ICP analysis. The uptake kinetics experiment was then repeated using Purolite A530E-ground for comparison.
Two kinetic models, including pseudo-first-order model (1) and pseudo-second-order model (2) were used to fit the sorption kinetics data. These two models can be expressed in the following equations:
where k1 and k2 (g mg−1 min−1) are the rate constants of pseudo-first-order and pseudo-second-order, respectively. qt is the sorption capacity at contact time t and can be calculated by the following equation: \(q_t = \frac{{\left( {C_0 - C_t} \right)V}}{m}\), where m and V are the mass of sorbent and solution volume, respectively. C0 and Ct are the concentration of ReO4−/TcO4− at initial time and time t, respectively. The linearized plot of pseudo-first-order model and pseudo-second-order model was obtained when we plotted \({\mathrm{ln}}(q_{\mathrm{e}} - q_t)\) and t/qt against t, respectively.
The distribution coefficient (Kd) of SCU-CPN-1 toward ReO4− was calculated by the following equation: \(K_{\mathrm{d}} = \frac{{\left( {C_0 - C_{\mathrm{e}}} \right)V}}{{mC_{\mathrm{e}}}}\), where Ce is the equilibrium concentration of ReO4−/TcO4−.
Sorption isotherm investigations
The sorption isotherm experiments of SCU-CPN-1 were conducted by varying the initial concentrations of ReO4− ranging from 10 to 2500 ppm. 10 mg of SCU-CPN-1 was added into 10 ml of ReO4− aqueous solution at pH 7 with the solid/liquid ratio of 1 g l−1. After being stirred at a rate of 120 rpm for 12 h, the suspension was separated with a 0.22 µm nylon membrane filter for ICP analysis. Sorption isotherms experiments of resins (Purolite A530E and A532E) were also carried out for comparison.
The Langmuir isotherm is based on the assumption that the sorption is monolayer sorption and all sites were equal. The linear equation of the Langmuir isotherm model is expressed as followed61:
where qm (mg g−1) is the maximum sorption capacity of Re(VII) corresponding to complete monolayer coverage and KL (l mg−1) is a constant indirectly related to sorption capacity and energy of sorption, which characterizes the affinity of the adsorbate with the adsorbent. KL is a constant of Langmuir model.
The Freundlich equation is an empirical equation based on sorption on a heterogeneous surface. The stronger binding sites are occupied first and with the increase of site occupation the binding strengths are decreased. The linear equation can be expressed by:
where KF and n are the Freundlich constants related to the sorption capacity and the sorption intensity, respectively.
pH effect study
The effect of pH value for ReO4− sorption was carried out by ranging pH values from 2 to 12. 10 mg of SCU-CPN-1 was added to 10 ml of aqueous solution containing 400 ppm ReO4−. After being stirred at a rate of 120 rpm for 12 h, the resulting mixture was separated with a 0.22 µm nylon membrane filter for ICP analysis.
Anion-exchange selectivity study
The effect of competing ions was studied by adding different concentration of NaNO3 (0.15 mM, 1.5 mM, 15 mM, and 150 mM) or Na2SO4 (0.015 mM, 0.15 mM, 1.5 mM, 15 mM, 150 mM, and 900 mM) into a 0.15 mM ReO4−solution, respectively. After being stirred at a rate of 120 rpm for 12 h, the suspension was separated with a 0.22 µm nylon membrane filter for ICP analysis.
Exchange experiments with simulated wastes
The simulated Hanford Low Activity Waste (LAW) Melter Recycle Stream was prepared according to a reported protocol18. Overall, 10 mg of SCU-CPN-1 was added to 10 ml of the above simulated wastes. After being stirred at a rate of 120 rpm for 12 h, the suspension was separated with a 0.22 µm nylon membrane filter for LSC analysis.
Batch experiments in 3 M HNO3 system
1 ml of aqueous solution containing 343 ppm ReO4− with 3 M HNO3 was mixed with 1 mg, 10 mg, 20 mg, 30 mg, 45 mg, 60 mg, and 90 mg of SCU-CPN-1-NO3 (SCU-CPN-1-NO3 was obtained by soaking SCU-CPN-1 in sat. NaNO3 solution for 12 h), respectively. After being stirred at a rate of 120 rpm for 12 h, the suspension was separated with a 0.22 µm nylon membrane filter for ICP analysis.
Reusability study
After SCU-CPN-1 was sorbed with 28 ppm of ReO4−at pH 7, 10 mg of ReO4−-sorbed material was eluted by 10 ml of various concentrations of NaCl solution at 25 °C, 60 °C, and 80 °C to search for the optimum desorption condition. 150 mg of SCU-CPN-1 was first sorbed with 150 ml 28 ppm of ReO4−at pH 7, and then the ReO4−-sorbed material was eluted by 150 ml of 1 mol l−1 NaCl solution at 80 °C for 12 h followed by washing with distilled water for three times.
Radiation-resistance measurements
A β irradiation experiment was conducted by irradiating SCU-CPN-1 at a dose rate of 50 kGy h−1 for four different doses (400, 600, 800, and 1000 kGy) and the source of β-ray was provided by an electron accelerator equipped with an electron beam (10 MeV). The γ-ray irradiation was provided by a 60Co irradiation source (92.42 PBq). SCU-CPN-1 was irradiated at a dose rate of 3.125 kGy h−1 or four different doses (400, 600, 800, and 1000 kGy), respectively. The radiation-resistance of SCU-CPN-1 was characterized by FT-IR spectroscopy and further checked by ReO4− uptake kinetics and capacity experiments measured on the irradiated samples.
Computational method
A [C6H5–C3N2H3–CH2–C6H5]+ fragment (M+ for short in the following, as shown in Supplementary Fig. 10) was used as the model for mimicking the positively charged local structure of the amorphous sorbent material of SCU-CPN-1. Four anions, including ReO4−, TcO4−, NO3−, and Cl− were used as the sorbates. The isolated structures of each anion and the complexes of M+A− (A− = ReO4−, TcO4−, NO3− and Cl−) were fully optimized in the gaseous phase using the B3LYP-D3/SDD~6-31G*62,63,64,65. For each complex, we considered various binding sites and the stable structures with lowest total energies are shown in Fig. 8. Higher precision single-point energy calculations were performed for these optimized structures in liquid phase (water as the solvent) at the M06-2×-D3/SDD~6-311++G**62,65,66,67,68 level. The SMD implicit solvent model was employed to consider the solvent effect. Based on the single-point energy calculations, the binding energies, Eb, were calculated as
where E(complex), E(M+), and E(anion) indicate the total energies of each complex, M+, and anions, respectively. All calculations were performed using the Gaussian 09 program69.
Data availability
All data are either provided in the Article and its Supplementary Information or are available from the corresponding author upon request.
References
Hodge, V. F., Koide, M. & Goldberg, E. D. Particulate uranium, plutonium and polonium in the biogeochemistries of the coastal zone. Nature 277, 206 (1979).
Taylor, R. Reaction: a role for actinide chemists. Chem 1, 662–663 (2016).
Dresselhaus, M. S. & Thomas, I. L. Alternative energy technologies. Nature 414, 332–337 (2001).
Ion, S. Reaction: recycling and generation IV systems. Chem 1, 663–665 (2016).
Lee, M. S. et al. Impeding 99Tc(IV) mobility in novel waste forms. Nat. Commun. 7, 12067 (2016).
Dickson, J. O., Harsh, J. B., Flury, M., Lukens, W. W. & Pierce, E. M. Competitive incorporation of perrhenate and nitrate into sodalite. Environ. Sci. Technol. 48, 12851–12857 (2014).
Popova, N. N., Tananaev, I. V., Rovnyi, S. I. & Myasoedov, B. F. Technetium: behaviour during reprocessing of spent nuclear fuel and in environmental objects. Russ. Chem. Rev. 72, 101–121 (2003).
Marchenko, V. I., Dvoeglazov, K. N. & Volk, V. I. Use of redox reagents for stabilization of pu and np valence forms in aqueous reprocessing of spent nuclear fuel: chemical and technological aspects. Radiochemistry 51, 289–302 (2009).
Zhou, X. et al. Chemical behavior of neptunium in the presence of technetium in nitric acid media. Radiochim. Acta 102, 111–116 (2014).
Banerjee, D., Kim, D., Schweiger, M., Kruger, J. & Thallapally, A. A.Removal of TcO4 − ions from solution: materials and future outlook. Chem. Soc. Rev. 45, 2724–2739 (2016).
Bonnesen, P. V. et al. Development of bifunctional anion-exchange resins with improved selectivity and sorptive kinetics for pertechnetate: batch-equilibrium experiments. Environ. Sci. Technol. 34, 3761–3766 (2000).
Pillay, K. K. S. A review of the radiation stability of ion exchange materials. J. Radioanal. Nucl. Chem. 102, 247–268 (1986).
Li, J. et al. Efficient uptake of perrhenate/pertechnenate from aqueous solutions by the bifunctional anion-exchange resin. Radiochim. Acta. 106, 581–591 (2018).
Wang, Y. & Gao, H. Compositional and structural control on anion sorption capability of layered double hydroxides (LDHs). J. Colloid Interf. Sci. 301, 19–26 (2006).
Zhu, L. et al. Selenium sequestration in a cationic layered rare earth hydroxide: a combined batch experiments and EXAFS investigation. Environ. Sci. Technol. 51, 8606–8615 (2017).
Gándara, F. et al. Layered rare-earth hydroxides: a class of pillared crystalline compounds for intercalation chemistry. Angew. Chem. Int. Ed. 45, 7998–8001 (2006).
Wang, S. et al. NDTB-1: a supertetrahedral cationic framework that removes TcO4 − from solution. Angew. Chem. Int. Ed. 49, 1057–1060 (2010).
Wang, S. et al. Selectivity, kinetics, and efficiency of reversible anion exchange with TcO4 − in a supertetrahedral cationic framework. Adv. Funct. Mater. 22, 2241–2250 (2012).
Sheng, D. et al. Efficient and selective uptake of TcO4 − by a cationic metal–organic framework material with open Ag+ sites. Environ. Sci. Technol. 51, 3471–3479 (2017).
Zhu, L. et al. Exceptional perrhenate/pertechnetate uptake and subsequent immobilization by a low-dimensional cationic coordination polymer: overcoming the hofmeister bias selectivity. Environ. Sci. Technol. Lett. 4, 316–322 (2017).
Zhu, L. et al. Identifying the recognition site for selective trapping of 99TcO4 − in a hydrolytically stable and radiation resistant cationic metal–organic framework. J. Am. Chem. Soc. 139, 14873–14876 (2017).
Banerjee, D. et al. Zirconium-based metal–organic framework for removal of perrhenate from water. Inorg. Chem. 55, 8241–8243 (2016).
Diercks, C. S. & Yaghi, O. M. The atom, the molecule, and the covalent organic framework. Science 355, 923 (2017).
Yaghi, O. M. Reticular chemistry—construction, properties, and precision reactions of frameworks. J. Am. Chem. Soc. 138, 15507–15509 (2016).
Liu, Y. et al. Weaving of organic threads into a crystalline covalent organic framework. Science 351, 365–369 (2016).
Alsbaiee, A. et al. Rapid removal of organic micropollutants from water by a porous β-cyclodextrin polymer. Nature 529, 190–194 (2016).
Ding, S. Y. et al. Thioether-based fluorescent covalent organic framework for selective detection and facile removal of mercury (II). J. Am. Chem. Soc. 138, 3031–3037 (2016).
Ma, H. et al. Cationic covalent organic frameworks: a simple platform of anionic exchange for porosity tuning and proton conduction. J. Am. Chem. Soc. 138, 5897–5903 (2016).
Sun, Q. et al. Postsynthetically modified covalent organic frameworks for efficient and effective mercury removal. J. Am. Chem. Soc. 139, 2786–2793 (2017).
Banerjee, D. et al. Removal of pertechnetate-related oxyanions from solution using functionalized hierarchical porous frameworks. Chem. Eur. J. 22, 17581–17584 (2016).
Tilford, R. W., Mugavero, S. J., Pellechia, P. J. & Lavigne, J. J. Tailoring microporosity in covalent organic frameworks. Adv. Mater. 20, 2741–2746 (2008).
Sun, Q. et al. Covalent organic frameworks as a decorating platform for utilization and affinity enhancement of chelating sites for radionuclide sequestration. Adv. Mater. 30, 1705479 (2018).
Li, B. et al. Functionalized porous aromatic framework for efficient uranium adsorption from aqueous solutions. ACS Appl. Mater. Interfaces 9, 12511–12517 (2017).
Li, B. et al. Creation of a new type of ion exchange material for rapid, high-capacity, reversible and selective ion exchange without swelling and entrainment. Chem. Sci. 7, 2138–2144 (2016).
Sun, Q. et al. Bio-inspired nano-traps for uranium extraction from seawater and recovery from nuclear waste. Nat. Commun. 9, 1644 (2018).
Zhu, Y., Wan, S., Jin, Y. & Zhang, W. Desymmetrized vertex design for the synthesis of covalent organic frameworks with periodically heterogeneous pore structures. J. Am. Chem. Soc. 137, 13772–13775 (2015).
Zou, X., Ren, H. & Zhu, G. Topology-directed design of porous organic frameworks and their advanced applications. Chem. Commun. 49, 3925–3936 (2013).
Das, S., Heasman, P., Ben, T. & Qiu, S. Porous organic materials: strategic design and structure–function correlation. Chem. Rev. 117, 1515–1563 (2016).
Rose, M. et al. N-heterocyclic carbene containing element organic frameworks as heterogeneous organocatalysts. Chem. Commun. 47, 4814−44816 (2011).
Nagai, A. et al. Pore surface engineering in covalent organic frameworks. Nat. Commun. 2, 536 (2011).
Kuhn, P., Antonietti, M. & Thomas, A. Porous covalent triazine-based frameworks prepared by ionothermal synthesis. Angew. Chem. Int. Ed. 47, 3450–3453 (2008).
Pachfule, P., Dhavale, V. M., Kandambeth, S., Kurungot, S. & Banerjee, R. Porous-organic-framework-templated nitrogen-rich porous carbon as a more proficient electrocatalyst than pt/c for the electrochemical reduction of oxygen. Chem. Eur. J. 19, 974−–9980 (2013).
Zhao, H., Li, L., Wang, Y. & Wang, R. Shape-controllable formation of poly-imidazolium salts for stable palladium n-heterocyclic carbene polymers. Sci. Rep. 4, 5478 (2014).
Darab, J. G. & Smith, P. A. Chemistry of technetium and rhenium species during low-level radioactive waste vitrification. Chem. Mater. 8, 1004−–11021 (1996).
McIntyre, L. J., Jackson, L. K. & Fogg, A. M. Ln2(OH)5NO3·xH2O (Ln = Y, Gd−Lu): a novel family of anion exchange intercalation hosts. Chem. Mater. 20, 335–340 (2008).
Li, Y. et al. Simultaneous speciation of inorganic rhenium and molybdenum in the industrial wastewater by amino-functionalized nano-SiO2. J. Taiwan Inst. Chem. E 55, 126–132 (2015).
Zu, J. H. et al. Preparation of a new anion exchanger by pre-irradiation grafting technique and its adsorptive removal of rhenium (VII) as analogue to 99Tc. Nucl. Sci. Technol. 26, 69–75 (2015).
Oliver, S. R. Cationic inorganic materials for anionic pollutant trapping and catalysis. Chem. Soc. Rev. 38, 1868–1881 (2009).
Gao, Y. et al. Interaction mechanism of Re (VII) with zirconium dioxide nanoparticles archored onto reduced graphene oxides. ACS Sustain. Chem. Eng. 5, 2163–2171 (2017).
Li, J., Chen, C., Zhang, R. & Wang, X. Reductive immobilization of Re(VII) by graphene modified nanoscale zero-valent iron particles using a plasma technique. Sci. China Chem. 59, 150–158 (2016).
Cui, X., Zhang, P., Wang, Y., Lou, Z. & Shan, W. Improving Re (VII) adsorption on diisobutylamine-functionalized graphene oxide. ACS Sustain. Chem. Eng. 5, 1010–1018 (2017).
Zu, J., Ye, M., Wang, P., Tang, F. & He, L. Design of a strong-base anion exchanger and its adsorption and elution behavior for rhenium (VII). RSC Adv. 6, 18868–18873 (2016).
Shu, Z. & Yang, M. Adsorption of rhenium (VII) with anion exchange resin D318. Chin. J. Chem. Eng. 18, 372–376 (2010).
Xiong, C., Yao, C. & Wu, X. Adsorption of rhenium (VII) on 4-amino-1,2,4-triazole resin. Hydrometallurgy 90, 221–226 (2008).
Jia, M. et al. Adsorption and separation of rhenium (VII) using N-methylimidazolium functionalized strong basic anion exchange resin. J. Chem. Technol. Biot. 88, 437–443 (2013).
Fei, H., Rogow, D. L. & Oliver, S. R. Reversible anion exchange and catalytic properties of two cationic metal−organic frameworks based on Cu(I) and Ag(I). J. Am. Chem. Soc. 132, 7202–7209 (2010).
Fei, H., Bresler, M. R. & Oliver, S. R. A new paradigm for anion trapping in high capacity and selectivity: crystal-to-crystal transformation of cationic materials. J. Am. Chem. Soc. 133, 11110–11113 (2011).
Desai, A. V., Manna, B., Karmakar, A., Sahu, A. & Ghosh, S. K. A water-stable cationic metal–organic framework as a dual adsorbent of oxoanion pollutants. Angew. Chem. Int. Ed. 55, 7811–7815 (2016).
Pillay, K. K. S. A review of the radiation stability of ion exchange materials. J. Radioanal. Nucl. Chem. 102, 247–268 (1986).
Sheng, G. et al. Enhanced immobilization of ReO4 − by nanoscale zerovalent iron supported on layered double hydroxide via an advanced XAFS approach: Implications for TcO4 − sequestration. AppL. Catal. B 192, 268–276 (2016).
Langmuir, I. The adsorption of gases on plane surfaces of glass, mica and platinum. J. Am. Chem. Soc. 40, 1361–1403 (1918).
Lee, C. T., Yang, W. T. & Parr, R. G. Development of the Colle-Salvetti correlation-energy formula into a functional of the electron density. Phys. Rev. B. 37, 785–789 (1988).
Grimme, S., Antony, J., Ehrlich, S. & Krieg, H. A consistent and accurate ab initio parametrization of density functional dispersion correction (DFT-D) for the 94 elements H-Pu. J. Chem. Phys. 132, 154104 (2010).
Hehre, W. J., Ditchfie, R. & Pople, J. A. Self-consistent molecular orbital methods. xii. Further extensions of gaussian—type basis sets for use in molecular orbital studies of organic molecules. J. Chem. Phys. 56, 2257–2261 (1972).
Andrae, D., Häußermann, U., Dolg, M., Stoll, H. & Preuß, H. Energy-adjustedab initio pseudopotentials for the second and third row transition elements. Theor. Chim. Acta 77, 123–141 (1990).
Zhao, Y. & Truhla, R. D. G. The M06 suite of density functionals for main group thermochemistry, thermochemical kinetics, noncovalent interactions, excited states, and transition elements: two new functionals and systematic testing of four M06-class functionals and 12 other functionals. Theor. Chem. Acc. 120, 215–241 (2008).
Mclean, A. D. & Chandler, G. S. Emission of the Hα and Hβ lines excited by electron impact on H2. J. Chem. Phys. 72, 5639–5648 (1980).
Clark, T., Chandrasekhar, J., Spitznagel, G. W. & Schleyer, P. V. Efficient diffuse function-augmented basis sets for anion calculations. III. The 3-21 + G basis set for first-row elements, Li–F. J. Comput. Chem. 4, 294−–2301 (1983).
Frisch, M. J. et al. Gaussian 09 (Gaussian, Inc, Wallingford CT, 2009).
Acknowledgements
This work was supported by the National Natural Science Foundation of China (21790370, 21790374, U1532259, 11605118, U1732112), the Natural Science Foundation of Jiangsu Province (BK20150313), the China Postdoctoral Science Foundation (2016M591901), the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD), and the “Young Thousand Talented Program” in China. O.K.F. and P.L. gratefully acknowledge financial support by Northwestern University and the U.S. Department of Energy, National Nuclear Security Administration under Award Number DE-NA0003763. T.E.A.-S. is supported as part of the Center for Actinide Science and Technology (CAST), an Energy Frontier Research Center funded by the U.S. DOE (DE-SC0016568).
Author information
Authors and Affiliations
Contributions
S.W. conceived and supervised the project. J.L. and C.X. designed and synthesized the material. J.L., C.X., L.Z., J.D., and M.A.S. carried out the uptake experiments and analyzed the data. L.Z., C.X., J.C., and Z.C. performed the Tc-99 experiments. P.L., O.K.F., and T.E.A.-S. aided in the structural analysis and the surface area measurement. L.C. performed the TEM-EDS analysis. D.Z. and H.Z. collected and analyzed the XPS and EXAFS data. Y.L. and D.Z. aided in the irradiation experiments. X.D. carried out the theoretical calculation. J.L., C.X., X.D., and S.W. wrote the paper. All authors discussed the results and commented on the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Li, J., Dai, X., Zhu, L. et al. 99TcO4− remediation by a cationic polymeric network. Nat Commun 9, 3007 (2018). https://doi.org/10.1038/s41467-018-05380-5
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-018-05380-5
This article is cited by
-
Polymer-on-HOF: a new strategy for fabricating “armour-plated” HOFs to sequester radioactive anions
Science China Chemistry (2024)
-
Synthesis of metal-free benzimidazole-based catalysts and its application in CO2 cycloaddition
Environmental Science and Pollution Research (2024)
-
Covalent organic frameworks (COF) materials for selective radionuclides removal from water
Journal of Radioanalytical and Nuclear Chemistry (2023)
-
Efficient removal of iodide/iodate from aqueous solutions by Purolite A530E resin
Journal of Radioanalytical and Nuclear Chemistry (2023)
-
An ionic vinylene-linked three-dimensional covalent organic framework for selective and efficient trapping of ReO4− or 99TcO4−
Nature Communications (2022)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.