To catch a quake


A revolution in seismic detection technology is underway, capturing unprecedented observations of earthquakes and their impacts. These sensor innovations provide real-time ground shaking observations that could improve emergency response following damaging earthquakes and may advance our understanding of the physics of earthquake ruptures.


On average, at least one earthquake of magnitude 7 or greater occurs each month somewhere around the globe. Many of these earthquakes go largely unnoticed as they occur in remote locations, but when a major earthquake happens near an urban centre it can result in substantial loss of life and economic losses. For example, the 2011 M9.0 Tohoku earthquake resulted in more than $300 billion USD in losses due to the earthquake and tsunami1, and the 2010 M7.0 Haiti earthquake caused significant loss of life with over 100,000 deaths1. The impacts of earthquakes are typically greater in developing countries where large populations centres are located in regions of high seismic hazard and the traditional building stock is more vulnerable to earthquake shaking1. Understanding the physics of how, when, and why large, potentially damaging earthquakes occur is critical for mitigating their effects. Yet, there are essentially no direct measurements of fault slip at the depths at which earthquakes start, typically a few to tens of kilometres below the Earth’s surface. Seismometers can accurately detect the displacement, velocity, or acceleration of the ground surface due to permanent shifts resulting from fault movement or the transient oscillations as seismic waves pass under a site. However, these data typically provide only scant observations as instruments are spaced too widely or data are not continuous in time.

Cost also presents a large impediment to long-term, dense (stations spaced at less than 10–20 km) ground motion observations. Research-grade, high-resolution seismic sensors are a fairly niche market with limited customers. These expensive specialty instruments are placed in long-term installations that are hardened to withstand strong shaking from earthquakes. Just one of these stations costs tens of thousands of dollars to build and equip, including sensors, on-site data acquisition systems, telecommunications, and back-up power. Multiple ground shaking measurements are required to locate and characterise an earthquake; and, in the event of a major earthquake the data are critical for determining the severity of shaking across the impacted region in order to guide emergency response to the hardest hit areas. Furthermore, earthquake early warning systems that rapidly detect earthquakes could provide critical warnings to affected populations prior to the arrival of damaging seismic waves, but these systems require dense instrumentation as every additional station improves the speed and accuracy of the alerts. Even the densest seismic networks in the world typically do not have more than one sensor every ~20 km, which can cost hundreds of thousands of dollars or more each year to operate and maintain. Operating a state-of-the-art seismic network can be beyond the reach of many developing countries leaving them especially vulnerable given the lack of data to understand local seismic hazards.

However, today earthquake sensing is in the midst of a renaissance as the methods available to more densely observe earthquake ground motions have expanded by leveraging both new types of purpose-built seismic instrumentation and new sensors in the built environment.

The revolution in seismic instrumentation

Advances in sensor and communication technologies are opening up opportunities for very dense purpose-built seismic sensors with lower per-station costs. The energy industry uses seismic sensors to undertake surveys of shallow Earth structure and through recent innovations cabled sensor systems have been converted into wireless nodal instruments2. These sensors eliminate the need for transport and installation of the heavy cables that once connected sensors together, and have batteries that last 30 or more days, making these systems attractive for use in earthquake studies. Without cables, the individual sensors are lightweight and easy to transport to remote locations so that station layouts can be better tailored to specific study targets. A 6-month deployment of 5400 sensors over a ~100 km2 area in Long Beach, California was deployed by industry, but data were made available to academic researchers. The data showed unexpected slip occurring in the deep roots of faults3 and provided insights into how shaking may vary across the region during a large earthquake by imaging the shallow subsurface4. A recent experiment on Mount St. Helens deployed a spiderweb of 904 nodes for 2 weeks providing an order of magnitude increase in the number of earthquakes observed beneath the active volcano compared to the existing traditional seismic network5. And, nodal arrays in Oklahoma are being used to track small earthquakes moving along previously undetected fault structures that are induced by injection of wastewater into deep wells in areas of oil and gas production6,7 (Fig. 1).

Fig. 1

Example of a M3.0 earthquake recorded by an 1800 sensor nodal array in Oklahoma. a Waveforms of the earthquake along one line of sensors; the times of the snapshots shown in b and c are shown by orange dashed lines, b Wavefield observed on 1800 nodes at 3.75 seconds after the earthquake origin time; red and blue colors denote when ground is moving up or down, respectively, and c Wavefield at 5.27 seconds after the origin time. (Image Credit: S. L. Dougherty, USGS)

While nodal array systems provide extremely dense sensor arrays at significantly lower costs than previously possible, they can only record ground motions over relatively short time periods (weeks to months). The advent of low-cost, ‘personal’ seismometers provides opportunities for long-term installations at only a few hundred dollars each, a fraction of the cost of a typical seismic station8,9. These systems utilise compact computers, often called plug computers, that are low power and inexpensive and take advantages of new advances in commercial-grade accelerometer sensors. The accelerometer chips are inexpensive as they are produced in bulk for use in activating car airbags, rotating smart phone screens, and gaming systems. While the sensors are lower resolution than scientific-grade instruments, they are adequate for recording moderate to strong ground motions and cheap enough to allow for building dense networks to observe ground motions on a block-by-block scale. Sensors installed by Community Seismic Network inside buildings have measured how buildings sway in response to passing earthquake waves providing real-world data to test the models that structural engineers have typically relied upon8. Raspberry Shake sensors are adding to local observations of ground motions from moderate to large earthquakes, including in countries with more limited seismic monitoring infrastructure9.

Everyday sensors

With plunging sensor prices, accelerometers are being integrated into many everyday objects making the idea of harnessing interconnected devices, or the so-called Internet of Things (IoT), for earthquake detection ever more attainable. Several groups have been working on collecting and combining data from consumer devices. The Quake Catcher Network pioneered the concept, by exploiting commercial-grade accelerometer inside laptops and smartphones and using distributed computing techniques to record data and detect quakes10. Rapid deployment of these sensors following the 2010 M8.8 Maule, Chile and the 2010 M7.2 Darfield, New Zealand earthquakes expanded the number of available observations from a few tens of research-grade sensors to hundreds of (lower-resolution) sensors used for rapid event detection, characterisation of local geology, and details about the earthquake sources11,12,13. MyShake also uses smartphones but integrates machine-learning techniques to separate quakes from other movement (walking, etc.)14. And, a system deployed in Chile (Fig. 2) uses the smartphone’s accelerometer chip to capture ground accelerations and a Global Positioning System (GPS) chip to capture ground displacements15, with application for earthquake and tsunami warning16.

Fig. 2

Smartphone set up as a dedicated seismic sensor to record earthquakes in Chile. (Image Credit: B. A. Brooks, USGS)

As described by Jousset et al.17 in a recent publication, fibre optic cables used for communication can be transformed into a series of sensors through the use of laser pulses that are backscattered in the fibre and recorded by a receiver. These sensors measure strain, i.e., very small changes in the length of the fibre cable (and the ground in which the fibre is installed) from extension and compression as seismic waves pass. Effective sensor spacing on the order of 1 to 10 m can be achieved, providing ten to fifty times more sensors over a given distance than even nodal systems. A 15-km-long fibre-optic cable with 4-m sensor spacing is providing new images of extraordinary resolution that show the deformation of faults in Iceland and seismic waves trapped within fault zones (Jousset et al.17). Fibre optic cables have also successfully recorded small earthquakes in Alaska and California at resolutions similar to scientific-grade equipment17,18. However, although promising, this approach requires significant development in order to translate and calibrate the data for widespread use.

The future of seismic observations

Each of these novel ground motion sensor networks provide incredible opportunities for recording rich datasets with which to study the movement of waves through the Earth and to decipher the inner workings of faults. Low-cost sensors may transform earthquake science in countries at significant risk of damaging earthquakes, but which may not be able to afford the high cost of installing and maintaining traditional seismic networks. There are still limitations to the resolution of the sensors, interpretation of the resulting data, and efficient management of the resulting large data volumes. Despite the limitations, I look forward to a time when smoke detectors and smart gas meters, or even perhaps millions of toasters provide records useful for seismology.


  1. 1.

    Daniell, J. E., Khazai, B., Wenzel, F. & Vervaeck, A. The CATDAT damaging earthquakes database. Nat. Hazards Earth Syst. Sci. 11, 2235–2251 (2011).

    ADS  Article  Google Scholar 

  2. 2.

    Slater, D. & Hollis, D. California’s dense urban environment spawns friendlier 3D seismic survey design. Oil Gas. J. 110, 54 (2012).

    Google Scholar 

  3. 3.

    Inbal, A., Ampuero, J. P. & Clayton, R. W. Localized seismic deformation in the upper mantle revealed by dense seismic arrays. Science 354, 88–92 (2016).

    ADS  Article  PubMed  CAS  Google Scholar 

  4. 4.

    Lin, F. C., Li, D., Clayton, R. W. & Hollis, D. High-resolution 3D shallow crustal structure in Long Beach, California: Application of ambient noise tomography on a dense seismic array. Geophysics 78, Q45–Q56 (2013).

    Article  Google Scholar 

  5. 5.

    Hansen, S. M. & Schmandt, B. Automated detection and location of microseismicity at Mount St. Helens with a large-N geophone array. Geophys. Res. Lett. 42, 7390–7397 (2015).

    ADS  Article  Google Scholar 

  6. 6.

    Anderson, K., Sweet, J. & Woodward, B. IRIS community wavefield experiment in Oklahoma. Incorporated Research Institutions for Seismology, Other/Seismic Network, (2016).

  7. 7.

    Dougherty, S. L., Cochran, E. S. & Harrington, R. M. Large-N Array Observations of Injection-Induced Seismicity in Northern Oklahoma: the LASSO Experiment. Abstract S23C-0821 presented at 2017 Fall Meeting, AGU, New Orleans, LA, 11–15 Dec. (2017).

  8. 8.

    Clayton, R. W. et al. Community seismic network: a dense array to sense earthquake strong motion. Seismol. Res. Lett. 86, 1354–1363 (2015).

    Article  Google Scholar 

  9. 9.

    Christensen, B. C. & Blanco Chia, J. F. Raspberry shake–a world-wide citizen seismograph network. Abstract S11A-0560 presented at 2017 Fall Meeting, AGU, New Orleans, LA, 11–15 Dec (2017).

  10. 10.

    Cochran, E. S., Lawrence, J. F., Christensen, C. & Jakka, R. The Quake-Catcher Network: Citizen Science expanding seismic horizons. Seismol. Res. Lett. 80, 26–30 (2009).

    Article  Google Scholar 

  11. 11.

    Chung, A. I. et al. The Quake-Catcher Network Rapid Aftershock Mobilization Program Following the 2010 M8.8 Maule, Chile Earthquake. Seismol. Res. Lett. 82, 526–532 (2011).

    Article  Google Scholar 

  12. 12.

    Lawrence, J. F. et al. MEMS accelerometers and distributed sensing for rapid earthquake characterization. Bull. Seismol. Soc. Am. 104, 184–192 (2014).

    Article  Google Scholar 

  13. 13.

    Neighbors, C. J., Cochran, E. S., Ryan, K. J. & Kaiser, A. E. Solving for source parameters using nested array data: a case study from the Canterbury, New Zealand earthquake sequence. Pure Appl. Geophys. 174, 875–893 (2017).

  14. 14.

    Kong, Q., Allen, R. M., Schreier, L. & Kwon, Y.-W. MyShake: a smartphone seismic network for earthquake early warning and beyond. Sci. Adv. 2, e1501055 (2016).

    ADS  Article  PubMed  PubMed Central  Google Scholar 

  15. 15.

    Brooks, B. A. et al. Smartphone-based earthquake and tsunami early warning in Chile. Abstract G31A-1045 presented at 2016 Fall Meeting, AGU, San Francisco, CA, 12–16 Dec (2016).

  16. 16.

    Minson, S. E. et al. Crowdsourced earthquake early warning. Sci. Adv. 1, e1500036 (2015).

    ADS  Article  PubMed  PubMed Central  Google Scholar 

  17. 17.

    Jousset, P. et al. Dynamic strain determination using fibre-optic cables allows imaging of seismological and structural features. Nat. Commun. (2018).

  18. 18.

    Lindsey, N. J. et al. Fiber-optic network observations of earthquake wavefields. Geophys. Res. Lett. 44, 11792–11799 (2017).

Download references


E.S.C. thanks K. Scharer and S. Minson for providing helpful U. S. Geological Survey internal reviews to this contribution.

Author information




E.S.C. solely contributed to the writing of this piece.

Corresponding author

Correspondence to Elizabeth S. Cochran.

Ethics declarations

Competing interests

The author declares no competing interests.

Additional information

Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Cochran, E.S. To catch a quake. Nat Commun 9, 2508 (2018).

Download citation

Further reading

  • Accurate Locations of Felt Earthquakes Using Crowdsource Detections

    • István Bondár
    • , Robert Steed
    • , Julien Roch
    • , Rémy Bossu
    • , Andres Heinloo
    • , Joachim Saul
    •  & Angelo Strollo

    Frontiers in Earth Science (2020)

  • Global quieting of high-frequency seismic noise due to COVID-19 pandemic lockdown measures

    • Thomas Lecocq
    • , Stephen P. Hicks
    • , Koen Van Noten
    • , Kasper van Wijk
    • , Paula Koelemeijer
    • , Raphael S. M. De Plaen
    • , Frédérick Massin
    • , Gregor Hillers
    • , Robert E. Anthony
    • , Maria-Theresia Apoloner
    • , Mario Arroyo-Solórzano
    • , Jelle D. Assink
    • , Pinar Büyükakpınar
    • , Andrea Cannata
    • , Flavio Cannavo
    • , Sebastian Carrasco
    • , Corentin Caudron
    • , Esteban J. Chaves
    • , David G. Cornwell
    • , David Craig
    • , Olivier F. C. den Ouden
    • , Jordi Diaz
    • , Stefanie Donner
    • , Christos P. Evangelidis
    • , Läslo Evers
    • , Benoit Fauville
    • , Gonzalo A. Fernandez
    • , Dimitrios Giannopoulos
    • , Steven J. Gibbons
    • , Társilo Girona
    • , Bogdan Grecu
    • , Marc Grunberg
    • , György Hetényi
    • , Anna Horleston
    • , Adolfo Inza
    • , Jessica C. E. Irving
    • , Mohammadreza Jamalreyhani
    • , Alan Kafka
    • , Mathijs R. Koymans
    • , Celeste R. Labedz
    • , Eric Larose
    • , Nathaniel J. Lindsey
    • , Mika McKinnon
    • , Tobias Megies
    • , Meghan S. Miller
    • , William Minarik
    • , Louis Moresi
    • , Víctor H. Márquez-Ramírez
    • , Martin Möllhoff
    • , Ian M. Nesbitt
    • , Shankho Niyogi
    • , Javier Ojeda
    • , Adrien Oth
    • , Simon Proud
    • , Jay Pulli
    • , Lise Retailleau
    • , Annukka E. Rintamäki
    • , Claudio Satriano
    • , Martha K. Savage
    • , Shahar Shani-Kadmiel
    • , Reinoud Sleeman
    • , Efthimios Sokos
    • , Klaus Stammler
    • , Alexander E. Stott
    • , Shiba Subedi
    • , Mathilde B. Sørensen
    • , Taka'aki Taira
    • , Mar Tapia
    • , Fatih Turhan
    • , Ben van der Pluijm
    • , Mark Vanstone
    • , Jerome Vergne
    • , Tommi A. T. Vuorinen
    • , Tristram Warren
    • , Joachim Wassermann
    •  & Han Xiao

    Science (2020)

  • Crowdsourcing triggers rapid, reliable earthquake locations

    • Robert J. Steed
    • , Amaya Fuenzalida
    • , Rémy Bossu
    • , István Bondár
    • , Andres Heinloo
    • , Aurelien Dupont
    • , Joachim Saul
    •  & Angelo Strollo

    Science Advances (2019)

  • Short Communication: Monitoring rockfalls with the Raspberry Shake

    • Andrea Manconi
    • , Velio Coviello
    • , Maud Galletti
    •  & Reto Seifert

    Earth Surface Dynamics (2018)


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.


Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing