Abstract
The photonic local density of states (LDOS) governs the enhancement of light–matter interaction at the nanoscale, but despite its importance for nanophotonics and plasmonics experimental local density of states imaging remains extremely challenging. Here we introduce a tomography scheme based on electron microscopy that allows retrieval of the threedimensional local density of states of plasmonic nanoparticles with nanometre spatial and subeV energy resolution. From conventional electron tomography experiments we obtain the threedimensional morphology of the nanostructure, and use this information to compute an expansion basis for the photonic environment. The expansion coefficients are obtained through solution of an inverse problem using as input electronenergy loss spectroscopy images. We demonstrate the applicability of our scheme for silver nanocuboids and coupled nanodisks, and resolve local density of states enhancements with extreme subwavelength dimensions in hot spots located at roughness features or in gaps of coupled nanoparticles.
Introduction
Plasmonics allows confinement of light at the nanoscale. This is achieved by binding light to coherent electron charge oscillations at the boundary of metallic nanoparticles, socalled particle plasmons, which come together with strong and tightly focused electromagnetic nearfields^{1,2,3}. While light confinement to extreme subwavelength dimensions holds promise for many applications, it hinders direct observation of the plasmonic nearfields by optical means because of the diffraction limit of light. An alternative measurement scheme is provided by electron energyloss spectroscopy (EELS) in a scanning transmission electron microscope (STEM), where a focused beam of swift electrons passes by or through metallic nanoparticles and the electrons can lose a small fraction of their kinetic energy through excitation of particle plasmons. By raster scanning the electron beam over the specimen and spectrally analyzing the electron energyloss, one can map the plasmonic nearfields with nanometre spatial and subeV energy resolution. This has been used intensively to investigate particle plasmons in various nanostructures, and has for instance allowed direct observation of coupling and quantum effects or optically dark modes^{4,5,6,7,8,9}.
Although the electron beam is a local probe, interpretation of the EELS signal is not straightforward. First of all the electron energyloss is determined by the integral effect of plasmonic nearfields along the beam path, thus masking information along the beam propagation direction. Second there is no generally valid simple link between a local physical quantity and the EELS signal. Though it was suggested that EELS might directly probe the photonic local density of states (LDOS)^{10}, a quantity of immense importance in nanophotonics, it was later shown that this holds only for special cases^{11}.
Tomographic reconstruction can in principle retrieve the threedimensional (3D) distribution of an unknown physical quantity from a series of projections with different viewing angles, under the assumption that probe–sample interactions are local in space and fulfill the projection requirement^{12}. Generally in the case of EELS the energy loss of electrons to plasmons is a nonlocal process, where the swift electron excites a plasmon oscillation and subsequently performs work against the induced plasmon field^{13}. However, under certain restrictive assumptions, such as the quasistatic approximation, applicable for nanoparticles much smaller than the wavelength of light, and a plasmonic response governed by a single resonance, one can formulate a conventional tomography scheme^{14}. For the quasistatic case, the EELS signal can be interpreted as a probe for the electrostatic potential along the beam trajectory and a threedimensional reconstruction of the potential has been demonstrated for a silver nanocube^{15}. In the same context it is also possible to trace the electrostatic potential back to surface charges^{14}, which has also been demonstrated experimentally^{16}. Unfortunately, these approaches come with several shortcomings (e.g., the schemes of refs. ^{14, 15} require a plasmonic response governed by a single mode and electron trajectories that do not penetrate the nanoparticle) and, more importantly, fail for larger nanoparticles beyond the quasistatic approximation^{14, 17}. In addition to EELS, cathodoluminescence (CL) is another technique based on electron microscopy that provides complementary information about the photonic environment^{18,19,20}. A comparative study between EELS and CL has been presented in ref. ^{21}, and a tomography study using CL is given in ref. ^{22}.
Here we demonstrate tomographic reconstruction of plasmonic nearfields through the solution of an inverse problem, following a recent proposal^{17}, and prove the applicability of this scheme using experimental EELS maps obtained for various nanoparticle geometries.
Results
Tomography scheme
The basic principle underlying our approach is shown in Fig. 1 and can be roughly divided into three steps. In the first step, we perform a tomographic experiment measuring EELS spectrum images (SIs) and highangle annular darkfield (HAADF) images for different tilt angles. From the HAADF data, we reconstruct the particle geometry, using a conventional tomography scheme^{23, 24}, and use the reconstructed particle geometry to compute for each loss energy the complexvalued plasmonic eigenmodes E _{ k }(r)^{17, 25}. A truncated set of these modes serves as a generic basis for the decomposition of the Green tensor^{25}
which, for given expansion coefficients C _{ k }, provides a complete characterization of the photonic environment of the plasmonic nanoparticle^{17, 26}. In a second step, we determine the coefficients C _{ k } using a minimization procedure. For some initial guess of C _{ k }, we compute the reprojected loss probabilities P _{rep}(R, θ) for different beam positions R and tilt angles θ, using the standard EELS equations^{13}, and then update C _{ k } such that
becomes minimized, where P _{exp} denotes the experimental EELS maps. In short, the second expression is minimal when the reprojected maps resemble the experimental ones as closely as possible, whereas the first expression favors a Green function decomposition with as few nonzero expansion coefficients as possible. Such a bias is in the spirit of compressed sensing optimizations^{27, 28} that have proven successful in a large number of applications including different problems in electron tomography^{15, 29,30,31}. μ is a parameter that weights between these two minimization objectives (for details see Methods). Once we have determined the best expansion coefficients C _{ k }, we have completely characterized the photonic environment of the plasmonic nanoparticle and can compute in a third step all quantities of interest, such as for instance the photonic LDOS.
It is worth emphasizing that the plasmonic eigenmodes E _{ k }(r) are solutions of the full Maxwell equations, thus our approach is suited for larger nanoparticles. As these modes provide a complete basis, similar to the Mie solutions for a spherical particle^{2}, in principle any photonic environment can be expressed in terms of Eq. (1) provided that the cutoff parameter n is chosen sufficiently large. However, to render Eq. (1) suitable for a compressed sensing optimization it is necessary that only a few coefficients C _{ k } differ significantly from zero, which can be achieved by using an expansion basis E _{ k }(r) well adapted to the problem (as we do by computing the modes for the tomographically reconstructed particle geometry).
Experiments
To demonstrate the applicability of our tomographic reconstruction scheme, we perform experiments on two types of plasmonic nanostructures created by electronbeam lithography on a thin Si_{3}N_{4} membrane: first a silver nanocuboid (dimensions 300 × 140 × 30 nm^{3}), and second two coupled silver nanodisks (diameter 180 nm, thickness 30 nm, gap 25 nm). While the nanocuboid serves as a proof of principle, investigations of the coupled disks allow direct visualization of coupling effects.
In the microscope, we acquire HAADF STEM images and EELS SIs at different tilt angles. The 3D morphology of the nanostructure is reconstructed using a totalvariation minimization algorithm^{24, 29, 31}. To extract plasmon resonance maps, spectra are pretreated with Richardson–Lucy deconvolution (Supplementary Figs. 1 and 2) and are integrated over a range of 0.19 eV around each resonance energy for each pixel of the SIs. The 3D reconstruction of the nanoparticle shape is used to simulate energyloss spectra and resonance maps for each tilt angle^{24, 32}, which in turn can be compared to experimental data.
For the nanocuboid sample, we identify two prominent resonance peaks in the loss spectra of Fig. 2a, which can be attributed to the dipolar and quadrupolar surface plasmon modes. The case of the coupled nanodisks is more complicated and several resonance peaks are visible in Fig. 2b; the lowest energy mode appears strongly localized at a protrusion attached to one of the nanodisks, the other ones are attributed to coupled edge modes of the disks^{9}.
LDOS reconstruction
Using the reconstructed morphology and angledependent plasmon resonance maps, we employ the scheme proposed above to determine the “best” coefficients C _{ k } and to reconstruct the dyadic Green tensor G of Eq. (1) (see Supplementary Figs. 3 and 4 for a comparison of experimental and reprojected EELS maps). From G we can compute any electrodynamical quantity of interest, such as the projected photonic LDOS^{26}
where ω is the angular frequency and c the speed of light. Similar to solidstate physics, where the LDOS provides the number of states accessible to electrons per unit energy and volume, the photonic LDOS provides the density of photonic states and describes how strongly a quantum emitter (e.g., fluorescent molecule or quantum dot) with dipole moment d oriented along direction n couples to the photonic environment^{10}. The decay rate of a dipole located at position r can be expressed as \({\Gamma _{{\rm{dip}}}} = (2\omega {d^2})/(3\hbar {\varepsilon _0}){\rho _{\bf{n}}}({\bf{r}})\), with ħ being the reduced Planck constant and ε _{0} the permittivity of vacuum. In free space, the photonic LDOS is ρ _{0} = ω ^{2}/(π ^{2} c ^{3})^{26}. Thus, ρ _{ n }(r)/ρ _{0} is the nearfield enhancement of the plasmonic nanoparticle. Below, we will display the photonic LDOS ρ _{ n }(r) in 3D as well as the averaged LDOS (obtained by averaging ρ _{ n } over all possible dipole orientations) at specific twodimensional (2D) slices through the volume. Throughout the LDOS maps are scaled to the respective maxima.
Figure 3 and Supplementary Movie 1 show the photonic LDOS for the dipolar and quadrupolar modes of the nanocuboid as reconstructed from the experimental EELS data. For comparison, we also show the simulated photonic LDOS, which is obtained from simulations using as input the particle geometry only. The different panels of the figure report a 3D view of the photonic LDOS, including the directional information discussed above, as well as slice projections of the averaged LDOS at different planes above and below the particle. We observe excellent agreement between the experimental and simulated LDOS maps, demonstrating the applicability of our reconstruction scheme. The projected LDOS follows the electric nearfield distribution of the dipolar and quadrupolar plasmon modes, however, without any information about forward or backward direction because ρ _{ n }(r) is averaged over the oscillation period of the fields.
The reconstructed photonic LDOS of the coupled nanodisks is shown in Fig. 4 and Supplementary Movie 2 for the five most prominent loss peaks in the EELS spectra (Fig. 2e). Mode (a) is strongly localized around the protrusion on the right particle, which is probably an artifact caused by an incomplete liftoff during electronbeam lithography fabrication. There is additionally a small but noticeable LDOS enhancement in the gap region that we interpret in terms of a hybridization between the localized mode and the bonding dipolar mode (b). For mode (b) the dipole moments of the individual particles are parallely aligned along the x direction. This leads to a strong nearfield and LDOS enhancement in the gap region, a socalled hot spot, which gives no significant signal in 2D EELS maps^{11} but can be clearly resolved in our tomographic reconstruction. For modes (c) and (d), the dipole moments of the individual particles are aligned parellely and antiparallely in the y direction, respectively, whereas for the antibonding mode (e), the individual dipole moments are aligned antiparallely in the x direction. As can be clearly seen in the right figure of panel (e), in the gap region the LDOS becomes strongly reduced and the electric nearfields point into the z direction.
Discussion
The comparison between the experimental and simulated EELS spectra in Fig. 2e is not perfect, although the reprojected EELS maps agree well with the measured ones (Supplementary Fig. 4). This demonstrates that our tomography approach is of general nature and that the plasmonic eigenmodes provide only a generic basis, without any significant bias in the reconstruction. The reason for the differences between experiment and simulation is not yet fully clear. The systematic energy shift of about 0.2 eV is in accordance to previous work^{24} and is most likely due to a different metallic dielectric function with respect to the one used in simulations, caused by silver being not monocrystalline and possible chemical changes between deposition and TEM experiments. Also the thin carbon layer, which is deposited on the samples is not taken into acccount in the simulations and may cause a shift. An additional energy shift is observed during the experiments, which is most likely caused by carbon contamination (Supplementary Figs. 5–7). In the simulated spectra of Fig. 2e, we observe for the protrusion mode a dip, reminiscent of a Fano lineshape^{34}, caused by the interaction with the energetically close bonding mode. As a side effect, the loss peak of the bonding mode is only faint, in contrast to experiment where the peak is clearly visible. Finally, in the experimental EELS maps we observe an additional small protrusion on the left particle that does not appear in the simulated and reprojected maps (Fig. 2 and Supplementary Fig. 4). This deficiency might be due to differences between the true particle morphology and the one used in simulations and reprojections, or a too small eigenmode basis.
As possible extensions of our work, an additional feedback loop between the simulation input, including particle geometry and dielectric functions, and the EELS sinograms could allow for geometry optimizations or dielectric function extractions. Preliminary theoretical work^{17} suggests that the tomographic reconstruction could be done with a significantly smaller number of measurement points, which would allow to diminish contaminationinduced peak shifts during data acquisition.
In conclusion, we have experimentally demonstrated a tomographic approach for reconstructing the complete photonic environment of plasmonic nanoparticles. Our approach is generally applicable to dielectric or metallic nanostructures, regardless of size and complexity. Future work will investigate structures consisting of composite materials and the coupling effects between plasmonic nanoparticles and quantum emitters, such as semiconductor quantum dots. The capability of mapping the threedimensional photonic environment with nanometre resolution is expected to be of great interest for a large variety of nanophotonics systems, such as dielectric spheres or localized cavity modes in photonic crystals.
Methods
Sample preparation
Electron beam lithography in a RAITH eline system was applied to produce silver nanostructures of 30 nm thickness on a 5 nm Si_{3}N_{4} membrane (TEMwindows) using a standard liftoff process with a poly(methylmetacrylate) resist^{9}. Grids with two rectangular Si_{3}N_{4} windows (1.5 mm × 100 μm) were chosen to allow imaging under large tilt angles. Several structures of different shapes and sizes were designed. The structures chosen for the experiments were nanocuboids with lateral dimensions of 300 nm × 140 nm and coupled disks with diameters of 180 nm and a gap distance of 25 nm. The nominal height of all particles was 30 nm. To eliminate charging during the TEM measurements, a thin carbon layer (∼1–2 nm) was sputtered on the sample (EPA 100, LeyboldHeraeus GmbH (Germany)). Without deposition of a carbon layer, movement of samples was observed in the TEM at large tilt angles.
EELS acquisition
Experiments were performed on a C_{S}probecorrected FEI Titan^{3} 60–300 microscope, with an XFEG fieldemission electron gun and a Wientype monochromator operated in decelerated gunlens mode. The acceleration voltage was 300 kV and excitation of the monochromator was set to 1.0. EELS spectra were acquired on a Gatan Imaging Filter (GIF Quantum) in hardwaresynchronized mode without binning. Energy spread of the monochromated beam was measured to 150 meV as fullwidth at halfmaximum of the zeroloss peak. The beam convergence semiangle was 15 mrad and the collection semiangle was 20.5 mrad. All spectrum images (SIs) were acquired with a size of 82 × 52 pixels at a pixel size of 7.7 nm with an exposure time of 5 ms per pixel. The total acquisition time for each spectrum image was 100 s. HAADF STEM survey images were acquired before SI acquisition with a pixel size of 1 nm at 1024 × 1024 pixels.
EELS data processing
All spectrum images were aligned in energy by shifting spectra relative to the positions of the zeroloss peak. After energyshift alignment the spectra were normalized to the maximum intensity of the zeroloss peak and deconvolved using Richardson–Lucy deconvolution with 25 iterations in a homemade analysis program for spectrum images^{36}. Spectra in the four corners of the spectrum images were averaged over 10 × 10 pixels per corner and were used as pointspread function for deconvolution. Supplementary Figs. 1 and 2 show the effects of the Richardson–Lucy deconvolution for spectra and resonance maps, respectively. In the spectra the contribution of the zeroloss peak is well removed and peaks are sharpened, while noise increases in the deconvolved data set. For resonance maps, little difference is visible before and after deconvolution, though removal of the background facilitates reconstruction. To extract 2D maps of surface plasmon resonances, the spectra were integrated over an energy region of 0.19 eV around the peak in the deconvolved spectrum images.
HAADF STEM and EELS SI tilt series acquisition
For the experiments, we used a Fischione 2020 tomography sample holder. For the nanocuboid sample tilt series were acquired between −75° and + 72° with steps of 10° from −70° to + 70° and two additional tilt angles at −75° and +72°, for the coupled disks the tilt range went from −75° to + 69° with steps of 15° from −75° to + 60° and two additional tilt angles at + 65° and + 69°. The additional tilt angles were used to maximize the tilt range at the highest possible sample tilt before shadowing of the sample. EELS SIs at each tilt angle were acquired and processed as described above. For the HAADF STEM reconstruction the survey images were used and rebinned by a factor of 2 to a pixel size of 2 nm.
Tilt series alignment
Alignment of the tomographic tilt series was done using center of mass methods based on the HAADF STEM survey images acquired just before EELS SI acquisition^{24}. The projections were aligned in xdirection and ydirection by calculating their center of mass. The tilt axis was found by calculating rotational centers from sinograms, based on the center of mass. The calculated alignment parameters were used to align both the HAADF STEM tilt series and the tilt series of EELS spectrum images. To compensate for the possible drift between the survey images and SI acquisition, the SIs were aligned to the corresponding survey image by crosscorrelation between the survey image and the HAADF signal acquired during SI acquisition.
Reconstruction of the HAADF STEM tilt series
The HAADF STEM tilt series was reconstructed using a totalvariation (TV) minimization algorithm using the full 3D gradient calculation as described in previous work^{31}. The normalization parameter μ was set to 2^{6}. The HAADF STEM reconstructions were segmented using an Otsu threshold. From the segmented reconstruction, a triangulation of the silver surface was calculated, which was used as input for both simulations and reconstruction of particle plasmon fields.
Reconstruction of photonic LDOS
The reconstruction of the photonic LDOS was performed as described in ref. ^{17}. As input geometry, reconstructions of the surface from HAADF STEM tilt series were used. The input geometry was aligned in xdirection and ydirection to correspond to the measured EELS maps. As an impact, parameters for the evaluation of the trajectory integrals pixel coordinates from the experimental EELS maps were used.
The compressed sensing minimization was performed with a L1/L2 optimization^{28} using the toolbox YALL1 (online at http://yall1.blogs.rice.edu). The mixing parameter was set to μ = 0.95. With the latter choice, we achieved good agreement between the measured and backprojected maps (Supplementary Figs. 3 and 4), while still introducing sufficient compressedsensing bias for a restricted eigenmode basis.
For the computation of the eigenmodes, we used surface reconstructions from HAADF STEM tilt series as described above. The number of triangulation elements was 1700 for the cuboid structure and 2700 for the coupled disks. The eigenmodes were obtained by computing the eigenvalues and eigenvectors of the Σ matrix from a boundary element approach, see Eq. (21) of ref. ^{35}, at the (real) frequencies of the plasmon resonances extracted from the simulated EELS spectra. For the cuboid structure, we also varied the frequencies for the eigenmode evaluation by ±0.2 eV, but did not find any significant changes of the reconstructed quantities. For the reconstruction procedure, we used the 50 eigenmodes of lowest energy. Consideration of more eigenmodes (up to 100) did not noticeably change the reconstructed quantities. Our compressed sensing optimization also turned out to be extremely robust with respect to the number of measurement points, as well as to other parameters such as μ.
For the dipolar and quadrupolar cuboid modes, we used EELS measurement data for angles from −50° to 50°. Because our BEM approach uses boundary elements of finite size, fields close to the boundary may suffer from discretization errors and we thus discarded in the reconstruction procedure impact parameters that were closer than 5 nm to the nanoparticle. Simulations and reprojections of EELS maps are compared with EELS measurements in Supplementary Fig. 3. The photonic LDOS of the coupled disks was reconstructed for five modes. For mode (a) of lowest energy, we used experimental EELS maps for tilt angles from −60° to 0°. EELS maps for larger tilt angles were not taken into account because of the contaminationinduced redshift during data acquisition. The remaining four modes were reconstructed from EELS maps for tilt angles −60° to 60°, −45° to 45°, −45° to 45° and −60° to 30°, respectively. Measured EELS maps and reprojections for different tilt angles are shown in Supplementary Fig. 4.
Simulation of EELS spectra and maps
The electron energyloss simulations for the two geometries were carried out with the MNPBEMToolbox^{17, 32, 37}. For simulations of EELS spectra, the same simplified surface reconstruction as for the calculation of eigenmodes was used. To account for the 5 nm thick Si_{3}N_{4} membrane used in experiment, we added a 5 nm thick layer with a permittivity of 4 at the bottom of the particles. Together with the layer structure, the overall number of triangulation elements was 6000 and 8000 for cuboid and coupled disks, respectively. A dielectric function obtained from optical experiments^{33} was used for both geometries. The reprojected maps were computed without consideration of the thin substrate.
Data availability
The data sets generated during and/or analysed during the current study are available from the corresponding author on reasonable request.
References
 1.
Barnes, W. L., Dereux, A. & Ebbesen, T. W. Surface plasmon subwavelength optics. Nature 424, 824–830 (2003).
 2.
Maier, S. A. Plasmonics: Fundamentals and Applications (Springer, 2007).
 3.
Mühlschlegel, P., Eisler, H. J., Martin, O. J. F., Hecht, B. & Pohl, D. W. Resonant optical antennas. Science 308, 1607–1609 (2005).
 4.
Nelayah, J. et al. Mapping surface plasmons on a single metallic nanoparticle. Nat. Phys. 3, 348–353 (2007).
 5.
Bosman, M., Keast, V. J., Watanabe, M., Maaroof, A. I. & Cortie, M. B. Mapping surface plasmons at the nanometre scale with an electron beam. Nanotechnology 18, 165505 (2007).
 6.
Boudarham, G. et al. Spectral Imaging of Individual SplitRing Resonators. Phys. Rev. Lett. 105, 255501 (2010).
 7.
Koh, A. L., FernándezDomínguez, A. I., McComb, D. W., Maier, S. A. & Yang, J. K. W. Highresolution mapping of electronbeamexcited plasmon modes in lithographically defined gold nanostructures. Nano Lett. 11, 1323–1330 (2011).
 8.
Scholl, J. A., Koh, A. L. & Dionne, J. A. Quantum plasmon resonances of individual metallic nanoparticles. Nature 483, 421–427 (2012).
 9.
Schmidt, F. P., Ditlbacher, H., Hohenester, U., Hohenau, A., Hofer, F. & Krenn, J. R. Dark plasmonic breathing modes in silver nanodisks. Nano Lett. 12, 5780–5783 (2012).
 10.
García de Abajo, F. J. & Kociak, M. Probing the photonic local density of states with electron energy loss spectroscopy. Phys. Rev. Lett. 100, 106804 (2008).
 11.
Hohenester, U., Ditlbacher, H. & Krenn, J. R. Electronenergyloss spectra of plasmonic nanoparticles. Phys. Rev. Lett. 103, 106801 (2009).
 12.
Hawkes, P. W. in Electron Tomography (ed. J. Frank) 17–38 (Plenum, 1992).
 13.
García de Abajo, F. J. Optical excitations in electron microscopy. Rev. Mod. Phys. 82, 209–275 (2010).
 14.
Hörl, A., Trügler, A. & Hohenester, U. Tomography of particle plasmon fields from electron energy loss spectroscopy. Phys. Rev. Lett. 111, 086801 (2013).
 15.
Nicoletti, O. et al. Threedimensional imaging of localized surface plasmon resonances of metal nanoparticles. Nature 502, 80–84 (2013).
 16.
Collins, S. M. et al. Eigenmode tomography of surface charge oscillations of plasmonic nanoparticles by electron energy loss spectroscopy. ACS Photonics 2, 1628–1635 (2015).
 17.
Hörl, A., Trügler, A. & Hohenester, U. Full threedimensional reconstruction of the dyadic green tensor from electron energy loss spectroscopy of plasmonic nanoparticles. ACS Photonics 2, 1429–1435 (2015).
 18.
Colliex, C., Kociak, M. & Stephan, O. Electron energy loss spectroscopy imaging of surface plasmons at the nanoscale. Ultramicroscopy 162, A1–A25 (2016).
 19.
GomezMedina, R., Yamamoto, N., Nakano, M. & Garcia de Abajo, F. J. Mapping plasmons in nanoantennas via cathodoluminescence. New J. Phys. 10, 105009 (2008).
 20.
Zagonel, L. F. et al. Nanometer scale spectral imaging of quantum emitters in nanowires and its correlation to their atomically resolved structure. Nano Lett. 11, 568–573 (2011).
 21.
Losquin, A. et al. Unveiling nanometer scale extinction and scattering phenomena through combined electron energy loss spectroscopy and cathodoluminescence measurements. Nano Lett. 15, 1229–1237 (2015).
 22.
Atre, A. C. et al. Nanoscale optical tomography with cathodoluminescence spectroscopy. Nature Nanotech 10, 429–436 (2015).
 23.
Midgley, P. A., Ward, E. P. W., Hungria, A. B. & Thomas, J. M. Nanotomography in the chemical, biological and materials sciences. Chem. Soc. Rev. 36, 1477–1494 (2007).
 24.
Haberfehlner, G. et al. Correlated 3D nanoscale mapping and simulation of coupled plasmonic nanoparticles. Nano Lett. 15, 7726–7730 (2015).
 25.
Sauvan, C., Hugonin, J. P., Maksymov, I. S. & Lalanne, P. Theory of the spontaneous optical emission of nanosize photonic and plasmon resonators. Phys. Rev. Lett. 110, 237401 (2013).
 26.
Novotny, L. & Hecht, B. Principles of NanoOptics (Cambridge University Press, 2006).
 27.
Candes, E. J. & Walkin, M. B. An introduction to compressed sensing. IEEE Signal Process. Mag. 25, 21–30 (2008).
 28.
Yang, J. & Zhang, Y. Alternating direction algorithms for l1problems in compressed sensing. SIAM J. Sci. Comput. 33, 250–278 (2011).
 29.
Saghi, Z. et al. Threedimensional morphology of iron oxide nanoparticles with reactive concave surfaces. A compressed sensingelectron tomography (CSET) approach. Nano Lett. 11, 4666–4673 (2011).
 30.
Goris, B. et al. Atomicscale determination of surface facets in gold nanorods. Nat. Mater. 11, 930–935 (2012).
 31.
Haberfehlner, G., Orthacker, A., Albu, M., Li, J. & Kothleitner, G. Nanoscale voxel spectroscopy by simultaneous EELS and EDS tomography. Nanoscale 6, 14563–14569 (2014).
 32.
Hohenester, U. & Trügler, A. MNPBEM – a matlab toolbox for the simulation of plasmonic nanoparticles. Comput. Phys. Commun. 183, 370–381 (2012).
 33.
Johnson, P. B. & Christy, R. W. Optical constants of the noble metals. Phys. Rev. B 6, 4370–4379 (1972).
 34.
Luk’yanchuk, B. et al. The Fano resonance in plasmonic nanostructures and metamaterials. Nat. Mater. 9, 707–715 (2010).
 35.
García de Abajo, F. J. & Howie, A. Retarded field calculation of electron energy loss in inhomogeneous dielectrics. Phys. Rev. B 65, 115418 (2002).
 36.
Schmidt, F.P., Hofer, F. & Krenn, J. R. Spectrum image analysis tool—a flexible MATLAB solution to analyze EEL and CL spectrum images. Micron 193, 43–51 (2017).
 37.
Waxenegger, J., Trügler, A. & Hohenester, U. Plasmonics simulations with the MNPBEM toolbox: consideration of substrates and layer structures. Comp. Phys. Commun. 1935, 138–150 (2015).
Acknowledgements
We are grateful to Joachim Krenn and Harald Ditlbacher for providing access to electron beam lithography and for helpful discussion. This work has been supported in part by the Austrian Science Fund FWF under project P27299N27 and the SFB F49 NextLite (F4906N23), by NAWI Graz, and by the European Union within the 7th Framework Program (FP7/2007–2013) under Grant Agreement no. 312483 (ESTEEM2).
Author information
Affiliations
Contributions
F.P.S. prepared the samples, G.H. performed TEM experiments, EELS data processing and reconstruction of the HAADF STEM data. A.H. and A.T. performed reconstruction of the photonic LDOS and simulations. All authors participated in the interpretation of the data and the data analysis, and helped in editing the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Hörl, A., Haberfehlner, G., Trügler, A. et al. Tomographic imaging of the photonic environment of plasmonic nanoparticles. Nat Commun 8, 37 (2017). https://doi.org/10.1038/s41467017000513
Received:
Accepted:
Published:
Further reading

HighFidelity 3D Nanoprinting of Plasmonic Gold Nanoantennas
ACS Applied Materials & Interfaces (2021)

Quantum correlations in electron microscopy
Optica (2021)

Fundamental Limit of Plasmonic Cathodoluminescence
Nano Letters (2021)

Threedimensional vectorial imaging of surface phonon polaritons
Science (2021)

Origin of functionality for functional materials at atomic scale
Nano Select (2020)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.