Skip to main content

Thank you for visiting You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

FeO–CeO2 nanocomposites: an efficient and highly selective catalyst system for photothermal CO2 reduction to CO



Solar-driven catalysis is a promising strategy for transforming CO2 into fuels and valuable chemical feedstocks, with current research focusing primarily on increasing CO2 conversion efficiency and product selectivity. Herein, a series of FeO–CeO2 nanocomposite catalysts were successfully prepared by H2 reduction of Fe(OH)3-Ce(OH)3 precursors at temperatures (x) ranging from 200 to 600 °C (the obtained catalysts are denoted as FeCe-x). An FeCe-300 catalyst with an Fe:Ce molar ratio of 2:1 demonstrated outstanding performance for photothermal CO2 conversion to CO in the presence of H2 under Xe lamp irradiation (CO2 conversion, 43.63%; CO selectivity, 99.87%; CO production rate, 19.61 mmol h−1 gcat−1; stable operation over 50 h). Characterization studies using powder X-ray diffraction and high-resolution transmission electron microscopy determined that the active catalyst comprises FeO and CeO2 nanoparticles. The selectivity to CO of the FeCe-x catalysts decreased as the reduction temperature (x) increased in the range of 300–500 °C due to the appearance of metallic Fe0, which introduced an additional reaction pathway for the production of CH4. In situ diffuse reflectance infrared Fourier transform spectroscopy identified formate, bicarbonate and methanol as important reaction intermediates during light-driven CO2 hydrogenation over the FeCe-x catalysts, providing key mechanistic information needed to explain the product distributions of CO2 hydrogenation on the different catalysts.


Modern societies are highly dependent on fossil fuel energy for electricity generation and transportation. Combustion of fossil fuels for energy releases CO2 into the atmosphere, thereby causing global warming and a plethora of associated environmental problems1,2,3. To curb anthropogenic CO2 emissions, researchers are now actively exploring different catalytic approaches for converting CO2 into fuels and valuable commodity chemicals4,5,6,7,8. As a form of CO2 sequestration, these catalytic approaches are particularly desirable, as they can generate economic value from CO2 (thereby transforming CO2 into a resource rather than an environmental problem requiring mitigation)1,4,9. However, transforming CO2 into other useful compounds such as CO, CH3OH, HCOOH, CH4, and C2+ hydrocarbons is challenging, requiring activation of strong C=O bonds10. Accordingly, the rates of CO2 reduction via photocatalytic methods and electrocatalytic methods are currently too low to justify serious consideration from industry11,12. A further challenge with CO2 reduction is achieving high selectivity for a specific product, which is highly desirable since it eliminates the need for separation of different reaction products. Most catalytic technologies for CO2 reduction developed to date are based on hydrogenation approaches, which typically utilize the Sabatier reaction (CO2 + 4H2 → CH4 + 2H2O) and/or the reverse water-gas shift (RWGS, CO2 + H2 → CO + H2O)3,13. While CO2 can be converted into CH4 and H2O via the Sabatier reaction, activation of CH4 for further conversion into other higher-value chemicals requires a considerable energy input14,15; thus, this approach for CO2 conversion to value-added chemicals is not practical. In comparison, the RWGS reaction creates CO, which can be used to synthesize fuels such as methanol or various hydrocarbons via Fischer-Tropsch syntheses6,16,17. In addition, CO can be used as a reducing agent for smelting many metals, such as iron. Therefore, the efficient conversion of CO2 into CO offers great economic and environmental benefits for future societies, motivating efforts to develop active and selective catalyst systems for this reaction.

Industrially, the RWGS reaction is a thermal catalytic process that utilizes transition metal-based catalysts, typically Fe, Co, Ni, Mn, Cu and combinations thereof, as the active phases18,19,20,21. Certain precious metal catalysts, such as Pt and Au, also show good activities for the RWGS reaction22,23,24, though they are not practical for industrial use due to their scarcity and susceptibility to poisoning. Similar to many other thermal catalytic processes, the RWGS reaction operates under relatively harsh reaction conditions (temperatures ranging from 400 to 700 °C and high pressures)25, thus requiring significant energy input to achieve meaningful CO2 conversion rates and yields of CO. Furthermore, at such high reaction temperatures, most RWGS catalysts show significant selectivity to CH4, thus yielding a product stream that contains CO and CH4, necessitating subsequent product separation26. However, lowering the reaction temperature generally improves the selectivity toward CO, though typically at the expense of a much lower CO2 conversion27. Recently, researchers have begun to explore light-driven photothermal processes as a means of driving the RWGS reaction under mild reaction conditions. In photothermal catalysis, strong absorption of solar photons by the catalyst results in catalyst heating to temperatures up to 450 °C, thus allowing traditional thermal catalytic processes to occur at reasonable rates28,29,30. Recently, Ye and coworkers reported photothermal CO2 hydrogenation to CH4 with good efficiency and selectivity over a series of group VIII nanocatalysts31. Subsequently, Zhang and coworkers reported photothermal CO2 hydrogenation to C2+ hydrocarbons using an alumina-supported Co–Fe alloy nanoparticle catalyst30. Similarly, Garcia’s group demonstrated that Co@C nanocomposites showed excellent photothermal catalytic performance for CO2 hydrogenation to C2+ hydrocarbons32. However, the photothermal RWGS reaction has received minimal attention to date, justifying a detailed investigation.

Herein, a series of novel FeO–CeO2 nanocomposite catalysts were prepared by H2 reduction of Fe(OH)3–Ce(OH)3 precursors at temperatures between 200 and 600 °C (the catalysts are denoted as FeCe-x, where x is the reduction temperature). The Fe:Ce molar ratio in the FeCe-x catalysts was varied from 1:2 to 3:1. The performance of the various FeCe-x catalysts for photothermal CO2 hydrogenation under light excitation (Xe lamp) was then examined. An FeCe-300 catalyst with an Fe:Ce ratio of 2:1 exhibited very high selectivity for photothermal CO2 hydrogenation to CO (Scheme 1). The catalyst, comprising FeO and CeO2 nanoparticles, could be heated to 419 °C under Xe lamp irradiation, resulting in a CO2 conversion of 43.63%, a CO selectivity of 99.87%, and a CO production rate of 19.61 mmol h−1 gcat−1. In situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) revealed that the RWGS reaction (CO2 + H2 → CO + H2O) occurred on the FeO component, thus accounting for the high selectivity toward CO shown by the FeCe-300 catalyst. For FeCe-x catalysts synthesized at higher H2 reduction temperatures, the appearance of metallic Fe0 enabled the Sabatier reaction (CO2 + 4H2 → CH4 + 2H2O) and thus decreased the photothermal CO2 hydrogenation selectivity toward CO. To our knowledge, the CO yield of 19.61 mmol h−1 gcat−1 yield and CO selectivity of 99.87% obtained here for the FeCe-300 catalyst are the highest yet reported for solar-driven CO2 hydrogenation. In addition, the FeCe-300 catalyst showed excellent stability during photothermal operation, with no loss in activity or change in CO selectivity detected over 50 h of testing. The results suggest that photothermal approaches can be very effective for solar-driven reduction of CO2 to CO.

Scheme 1

Fabrication of FeCe-x catalysts by hydrogen reduction of Fe(OH)3–Ce(OH)3 precursors at 200–600 °C. The product distribution of each catalyst for CO2 hydrogenation under light irradiation is indicated.

Materials and methods


Ce(NO3)3·9H2O, Fe(NO3)3·9H2O, commercial CeO2, and urea were purchased from Beijing Chemical Works (Beijing, China). All the reagents were of analytical grade and used without further purification. The reaction gas mixture used in the CO2 hydrogenation tests (CO2/H2/Ar = 15/60/25) was purchased from Beijing Sikeda Company (Beijing, China).

Catalyst preparation

The FeCe-x nanocomposite catalysts were prepared by H2 reduction of Fe(OH)3–Ce(OH)3 precursors at temperatures in the range of 200–600 °C. Briefly, precursors were prepared via a simple precipitation reaction. Typically, 0.01 mol of Fe(NO3)3·9H2O, 0.005 mol of Ce(NO3)3·9H2O and 0.1 mol of urea were dissolved in 100 mL of deionized water. The resulting homogeneous solution was then refluxed at 110 °C for 24 h under magnetic stirring. After cooling to room temperature, the product was collected by centrifugation and washed repeatedly with deionized water and finally dried at 60 °C under vacuum. The product, a mixture of Fe(OH)3 and Ce(OH)3, was then transferred to a tubular furnace and reduced at different temperatures between 200 and 600 °C under a hydrogen atmosphere (H2/Ar = 10/90). A heating rate of 5 °C min−1 was used in all experiments. The final products are denoted as FeCe-x, where x refers to the reduction temperature. For the FeCe-300 catalysts, the Fe:Ce molar was also varied to examine the effect of the Fe:Ce ratio on catalyst performance for photothermal CO2 hydrogenation. Commercial CeO2 with a particle size of ~50 nm was purchased from a commercial supplier and used as a reference catalyst.


Powder X-ray diffraction (XRD) patterns for the FeCe-x catalysts were collected on a Bruker D8 Focus X-ray diffractometer equipped with a Cu Kα radiation source (λ = 1.5405 Å) operating at 40 kV. X-ray photoelectron spectroscopy (XPS) data were obtained on a VGESCALABMKII X-ray photoelectron spectrometer using a nonmonochromatized Al-Kα X-ray source. Transmission electron microscopy (TEM) and high-resolution TEM (HRTEM) images were collected on a JEOL-2100F microscope operating at an accelerating voltage of 200 kV. The samples were dispersed on hydrophilic carbon films for the analyses. The instrument was also equipped for high-angle annular dark-field scanning TEM (HAADF-STEM) imaging and energy-dispersive X-ray (EDX) elemental mapping. Quantitative EDX analyses were performed on a Hitachi S-4800 scanning electron microscope. UV-vis diffuse reflectance spectra were collected on a Beijing PGENERAL TU-1901 spectrometer with an integrating sphere attachment. The spectra were recorded over the wavelength range of 200–2000 nm. DRIFTS data were recorded on a Vector 70v (Brucker) infrared spectrometer with a custom-built reaction cell (as described below).

CO2 hydrogenation tests under light irradiation

The CO2 hydrogenation tests were carried out in a flow reaction system consisting of a Teflon-lined stainless reaction chamber (50 cm−3) with a quartz window, a gas inlet and outlet, an electronic flowmeter to monitor the inlet gas flow rate and a thermocouple to measure the catalyst temperature (Figure S1, Supporting Information). For each test, 50 mg of catalyst was uniformly dispersed on a light-permeable quartz fiber filter. Next, the reaction gas mixture (CO2/H2/Ar = 15/60/25, flow rate 15 mL min−1) was introduced into the reactor to achieve a pressure of 0.18 MPa. The system was then kept under these conditions for 1 h to eliminate any residual oxygen in the reactor. Then, the catalyst bed was irradiated with a 300 W Xe lamp (Beijing Perfect-light Co. Ltd, PLS-SXE-300 UV, light intensity 2.2 W cm−2) to initiate photothermal CO2 conversion. After 1 h of irradiation, a gas sample was taken from the reactor by syringe and analyzed by a Shimadzu GC-2014 chromatograph (Shimadzu Co, Japan) equipped with a three-channel analysis system. The first channel analyzed hydrocarbons in an HP PLOT Al2O3 column, with He as the carrier gas and a flame ionization detector (FID). The second channel analyzed CO2, N2, Ar, O2, CH4, and CO using a combination of micro packet Haysep Q, H-N and Molsieve 13× columns, employing He as the carrier gas and a thermal conductivity detector (TCD). The third channel analyzed H2 using a micropacket HayeSep Q and Molsieve 5 Å column with N2 as the carrier gas and a TCD detector. CO2 conversion and product selectivity were determined by an internal standard method that used Ar. The CO yield was calculated from two standard curves with R2 = 0.999.

Blank control experiments were also performed. Blank-1 tests were carried out under the same conditions as a normal test but without any catalyst. Blank-2 tests were carried out under the same conditions as a normal test but without the CO2/H2/Ar = 15/60/25 reaction gas. Both blank tests were performed after 1 h of illumination under a Xe lamp.

In situ DRIFTS studies of light-induced CO2 hydrogenation

In situ DRIFTS was applied to study the surface intermediates formed during photothermal CO2 hydrogenation on the different FeCe-x catalysts. A Vector 70v (Brucker) spectrophotometer equipped with a custom-built in situ diffuse reflectance cell was used for the DRIFTS studies. A 300 W Xe lamp was used as the light source for photothermal experiments. The in situ cell was also equipped with an electric heating device to allow specific reaction temperatures to be reached (i.e., the same temperatures that were realized in the photothermal catalytic tests). For each test, 50 mg of catalyst was loaded into the reaction cell, and a background spectrum was collected under vacuum. Subsequently, a gas mixture containing CO2 and H2 (v/v = 1/4) was introduced to achieve an absolute pressure of 0.18 MPa. The reaction cell was maintained in this state for 30 min to allow adsorption–desorption equilibrium to be attained. Next, the 300 W Xe lamp and the electric heating device were applied to heat the catalyst and thus accurately simulate the temperature profiles realized in the photothermal catalytic tests. In situ DRIFTS spectra were collected every minute over a period of 1 h at 4 cm−1 resolution.


Composition and morphology of the FeCe-x catalysts

The FeCe-x nanocomposite catalysts were prepared by H2 reduction of a mixed hydroxide precursor with an Fe:Ce atom ratio of 2:1 (Figures S2 and S3, Supporting Information) at temperatures ranging from 200 to 600 °C. The obtained FeCe-x catalysts (where x is the reduction temperature) were characterized in detail by XRD and XPS. Figure 1a shows XRD patterns for the catalysts prepared at different reduction temperatures (x = 200–600 °C). The FeCe-200 catalyst showed characteristic reflections for CeO2 (28.5, 33.1, 47.5, 56.3, and 59.1°, JCPDS-34-0394) and Fe2O3 (35.7 and 43.3°, JCPDS-25-1402). The data indicate that heating at 200 °C under H2 was sufficient to transform the mixed hydroxide precursor into a mixed oxide nanocomposite. Upon increasing the reduction temperature to 300 °C, FeO (36.0 and 41.9°, JCPDS-06-0615) became the dominant Fe-containing phase. When the reduction temperature was increased above 400 °C, peaks due to metallic Fe0 appeared (44.7 and 65.0°, JCPDS-65-4899), while the FeO peaks were attenuated, providing direct evidence for FeO reduction to Fe0. At all reduction temperatures (x), CeO2 was the dominant cerium-containing phase. The Fe 2p XPS spectra in Fig. 1b (referenced against the C 1s signal of adventitious hydrocarbons at 284.7 eV) revealed changes similar to those seen by XRD with increasing H2 reduction temperature. At reduction temperatures up to 400 °C, only cationic Fe2+ and Fe3+ states with associated shake-up satellites were observed, consistent with the presence of FeO and Fe2O3, respectively. At reduction temperatures above 400 °C, new peaks appeared at low binding energies relative to the Fe2+/Fe3+ features, which can be readily ascribed to metallic Fe0 (e.g., Fe 2p3/2 = 706.7 eV), in perfect accord with the XRD results.

Fig. 1

a XRD patterns for the different FeCe-x catalysts (Fe:Ce molar ratio = 2:1). b Fe 2p XPS spectra for the FeCe-x catalysts and the FeCe hydroxide precursor. c UV-vis absorption spectra for the FeCe hydroxide precursor, FeCe-x catalysts and commercial CeO2. d Catalyst surface temperature for the FeCe-x catalysts and FeCe hydroxide precursor under light irradiation.

UV-vis absorption spectra were collected for the FeCe-x catalysts to gauge their light absorption properties. Strong absorption at UV, visible and NIR wavelengths was important to their function as photothermal catalysts for CO2 hydrogenation (Fig. 1c). The FeCe precursor and FeCe-200 catalyst showed strong absorption below 500 nm due to the presence of Fe3+ and Ce4+ species. In contrast, the FeCe-x catalysts reduced at temperatures of 300 °C or above absorbed strongly from 200 to 2000 nm, indicating that they possessed excellent light absorption properties (since CeO2 only absorbs light weakly at visible wavelengths, the strong absorption by the FeCe-x catalysts with x = 300–600 can mainly be attributed to the presence of FeO and Fe0). In addition, the light absorption characteristics of FeCe-300 catalysts with different Fe:Ce molar ratios were also studied (Figure S4, Supporting Information). The FeCe-300 catalyst with the highest Fe:Ce molar ratio of 2:1 showed the strongest light absorption ability among the catalysts studied, again consistent with FeO rather than CeO2 being the dominant light absorber in these nanocomposite catalysts. Next, the photothermal heating of the various FeCe-x catalysts under 300 W Xe lamp irradiation was examined. A thermocouple was used to monitor the surface temperature of the catalysts as a function of the irradiation time. As shown in Fig. 1d, the surface temperatures of FeCe-300, FeCe-400, FeCe-500 and FeCe-600 catalysts (Fe:Ce molar ratio 2:1) increased rapidly over the first 25 min of irradiation and then stabilized at 419, 425, 440, and 446 °C, respectively. In comparison, the photothermal heating effects for the FeCe precursor and the FeCe-200 catalyst were obviously weaker, consistent with these two samples being less effective absorbers at UV-visible-NIR wavelengths than the other FeCe-x catalysts.

Photothermal CO2 hydrogenation performance

The CO2 hydrogenation activity of the FeCe-x catalysts and selected reference catalysts (FeCe precursor and commercial CeO2) were evaluated in a flow system under light irradiation (0.18 MPa, 15 mL min−1, CO2/H2/Ar = 15/60/25) without any external heating. The results of the CO2 hydrogenation tests are summarized in Table 1. Blank experiments showed that no hydrocarbons or CO formed in the absence of a catalyst (Blank-1) or reactant gas (Blank-2). These experiments confirmed that the reaction device did not catalyze CO2 hydrogenation and that the catalyst itself did not decompose to produce hydrocarbons or CO. As shown in Fig. 2b and Table 1, the FeCe hydroxide precursor and FeCe-200 showed minimal activity (conversion of CO2 <15%) for CO2 hydrogenation under Xe lamp irradiation, which can be rationalized by their relatively weak absorption properties in the 200–2000 nm range, indicating that photothermal heating was modest (i.e., not in the ideal range for CO2 hydrogenation). In contrast, the FeCe-300 catalyst showed remarkable activity for CO2 hydrogenation under Xe lamp irradiation, achieving a 44.33% CO2 conversion with an excellent selectivity toward CO of 99.87% (Fig. 2a). Upon increasing the precursor reduction temperature to 400 °C and then to 500 °C, there was no significant change in the CO2 conversion (42.05% and 40.89%, respectively), but the CO selectivity decreased progressively (95.65% and 92.01%, respectively). When the precursor reduction temperature was increased to 600 °C, the CO2 conversion dropped sharply to 22.75% (with CO selectivity 94.32%) due to sintering in the nanocomposite catalysts, which reduced the active area of the active Fe component. The decrease in the selectivity to CO from FeCe-300 to FeCe-500 was accompanied by a simultaneous increase in the selectivity to CH4, with the formation of CH4 coinciding with the appearance of Fe0 in the catalysts (see Fig. 1). The specific CO yield for the FeCe-300 catalyst was 19.61 mmol h−1 gcat−1, higher than that obtained using any of the other FeCe-x catalysts. Based on this finding, we then examined the CO2 hydrogenation performance of FeCe-300 catalysts prepared with different Fe:Ce molar ratios (Fig. 2c, Table 1). The Fe:Ce ratio of 2:1 delivered the best performance and highest CO2 conversion among the FeCe-300 catalysts tested, reflecting its superior light absorption abilities (Figure S4, Supporting Information). Interestingly, the selectivity to CO of the various FeCe-300 catalysts was similar, consistent with all these catalysts containing the same active phase (FeO). On the basis of photothermal heating properties, CO2 conversion, CO selectivity and CO yield, the FeCe-300 catalyst with an Fe:Ce molar ratio of 2:1 was identified as the best catalyst for CO2 hydrogenation to CO among the various FeCe-x nanocomposites prepared in the current study. The results also demonstrate that the surface composition of the FeCe-x catalysts, especially the relative proportions of Fe2O3, FeO, and Fe0, strongly influences the product distribution for CO2 hydrogenation. FeO is identified as the active site for the photothermal RWGS reaction and is thus responsible for the very high CO selectivity observed for the FeCe-300 catalyst. Metallic Fe0 promotes photothermal CO2 hydrogenation to CH4 and H2O (i.e., the Sabatier reaction), thus explaining why the FeCe-400, FeCe-500, and FeCe-600 catalysts, which contain both FeO and Fe0, afforded lower selectivities to CO than the FeCe-300 catalyst (containing only FeO).

Table 1 CO2 conversion and product distribution for photoinduced CO2 hydrogenation over various FeCe-x catalysts (Fe:Ce molar ratio = 2:1), FeCe-300 catalysts with different ratios of Fe:Ce molar ratios, commercial CeO2 and blank experiments (Blank-1: no catalyst, Blank-2: no CO2/H2/Ar = 15/60/25 reaction gas)
Fig. 2

a Product selectivity toward CO and CH4 for photothermal CO2 hydrogenation over the FeCe hydroxide precursor and FeCe-x catalysts (Fe:Ce molar ratio = 2:1). b CO2 conversion and product yields of CH4 and CO for the FeCe hydroxide precursor and FeCe-x catalysts. c CO2 conversion and product selectivity to CH4 and CO for FeCe-300 catalysts with different Fe:Ce molar ratios. Data for commercial CeO2 are also shown. d CO2 conversion, product yields and product selectivities over 50 h of CO2 hydrogenation tests. Reaction conditions: 50 mg catalyst, 300 W Xenon lamp, 5 cm irradiation distance, pressure of 0.18 MPa, reaction gas composition of CO2/H2/Ar = 15/60/25.

Cycle tests of photothermal CO2 hydrogenation were conducted on the FeCe-300 catalyst (Fe:Ce 2:1) to verify its stability. As shown in Fig. 2d, the FeCe-300 catalyst showed no significant change in CO2 conversion (fluctuating between 40 and 52%), CO selectivity (97–99.9%) or CO yield (~20 mmol h−1 gcat−1) over 50 h of testing. The test confirmed that the FeCe-300 catalyst possessed excellent stability under the photothermal testing regime used here for CO2 hydrogenation tests.

Morphological evolution of the FeCe-x catalysts

Since the activities and product selectivities of the FeCe-x catalysts for photothermal CO2 hydrogenation were closely related to their surface Fe speciation, TEM and HRTEM were applied to further examine the morphologies and dispersion of FeO and Fe0 in the catalysts. The FeCe-x catalysts all existed as nanoparticle clusters, with the mean size of the nanoparticles in the clusters increasing in size as the reduction temperature increased in the range 200–600 °C (Fig. 3a and Figure S6, Supporting Information). Obviously, increasing the reduction temperature caused nanoparticle sintering and grain growth, which was especially evident at the higher reduction temperature of 600 °C, where large FeO/Fe0 nanoparticles were observed to form (accounting for the loss of the sharp drop in CO2 conversion observed for the FeCe-600 sample during photothermal CO2 hydrogenation tests, see Table 1). The FeCe-300 catalyst with the best CO2 hydrogenation performance was further characterized by HRTEM, HAADF-STEM and EDX elemental mapping (Fig. 3). HRTEM lattice fringes with spacings of 0.31 and 0.25 nm were observed, corresponding to the CeO2(111) and FeO(111) planes, respectively (Fig. 3b). EDX mapping established a very uniform distribution of Ce, Fe, O in the FeCe-300 catalyst (Fig. 3c, d), as was expected given the very small size of the FeO and CeO2 crystallites formed at a reduction temperature of 300 °C. The identification of discrete FeO and CeO2 nanoparticles further confirmed that the sample was indeed a nanocomposite of FeO and CeO2 (in agreement with XRD), as opposed to a ternary oxide phase. Since pure CeO2 demonstrated negligible CO2 hydrogenation activity under Xe lamp irradiation, it can be concluded that the function of CeO2 in the FeCe-x catalysts was to (1) maintain a high dispersion of active FeO and Fe0 components and (2) act as a cocatalyst to assist with the activation of CO2 (e.g., under photothermal reaction conditions, CeO2 will exist as CeO2-x, thus activating CO2 adsorption through surface VO), as suggested by other reports33,34,35.

Fig. 3

Morphological characterization of the FeCe-300 catalyst (Fe:Ce molar ratio = 2:1). a TEM image. b HRTEM image. c HAADF-STEM image. d Overlayed EDS element map and individual EDS maps for O, Fe, and Ce.

In situ DRIFTS studies of photothermal CO2 hydrogenation

To rationalize the different selectivities of FeO and Fe0 for photothermal CO2 hydrogenation, in situ DRIFTS was used to identify key intermediates formed during photoinduced CO2 hydrogenation on FeCe-300 (containing only FeO) and FeCe-500 (containing both FeO and Fe0). For the FeCe-300 catalyst, peaks due to adsorbed CO2, chelating bridged carbonate (c-CO32−, 1704 cm−1), monodentate carbonate (m-CO32−, 1519 and 1315 cm−1) and bidentate carbonate (b-CO32−, 1338 cm−1)36 appeared after reaction for 1 min (Fig. 4a). As the reaction proceeded, additional intermediate species, including bicarbonate (HCO3, 1650 and 1423 cm−1) and CO2 (1681 and 1268 cm−1)37,38, were detected. Bicarbonate is a key intermediate in the RWGS reaction; thus, its detection here was not surprising since the FeCe-300 showed a very high selectivity for CO2 hydrogenation to CO38. As the reaction continued, the characteristic peaks of adsorbed CO2 and all the other intermediate species above decreased in intensity, indicating the consumption of these species as the reaction achieved a high steady-state rate. The development of a broad peak at 3250 cm−1 corresponding to adsorbed water as the reaction time approached 1 h was entirely consistent with expectations for the RWGS (CO2 + H2 → CO + H2O). The DRIFTS data thus provide convincing evidence that the RWGS reaction was the dominant surface reaction on the FeCe-300 catalyst under Xe lamp irradiation, hence explaining the high selectivity of the FeCe-300 catalyst for photothermal CO2 hydrogenation to CO (>99% selectivity). For the FeCe-500 catalyst containing FeO and Fe0, different intermediates emerged (Fig. 4b). In the first few minutes of the reaction, three kinds of adsorbed CO2 (1716, 1519, 1315, and 1338 cm−1), a bicarbonate species (1650 and 1423 cm−1), and CO2 (1681 and 1268 cm−1) were detected. In addition, bands associated with formate (1592 cm−1) and methanol (1050 cm−1) appeared, which are key intermediates of the Sabatier reaction (CO2 + 4H2 → CH4 + 2H2O)38. With increasing reaction time, the peaks associated with adsorbed CO2, bicarbonate and CO2 lost intensity as was observed for FeCe-300, while the bands associated with formate and methanol were more persistent due to their continuous production and consumption. The results suggest that both the RWGS reaction and the Sabatier reaction occurred on the surface of the FeCe-500 catalyst, utilizing FeO and Fe0 active sites, respectively. The product distributions of CO2 hydrogenation over the FeCe-300 catalyst (RWGS pathway yielding only CO) and FeCe-500 catalyst (RWGS yielding CO and Sabatier pathway yielding CH4) can be easily rationalized on this basis, highlighting the value of in situ DRIFTS for mechanistic assessment of working catalysts. To our knowledge, this is the one of the first occasions that DRIFTS has been successfully applied for the mechanistic investigation of a photothermal catalytic reaction.

Fig. 4

In situ DRIFT spectra for photoinduced CO2 hydrogenation on a FeCe-300 and b FeCe-500. For both catalysts, the Fe:Ce molar ratio was 2:1. The spectra were collected at a resolution of 4 cm−1 over a period of 1 h.


In conclusion, a series of FeCe-x nanocomposite catalysts were successfully synthesized by a simple precipitation-reduction method. By varying the H2 reduction temperature (x) in the range of 200–600 °C, the valence state of Fe in the catalysts could be adjusted from Fe2O3 to FeO and then Fe0 at high temperatures (the Fe-containing phases were dispersed by CeO2 at all temperatures). An FeCe-300 catalyst with an Fe:Ce molar ratio of 2:1 exhibited remarkable performance for photothermal CO2 hydrogenation to CO (CO selectivity, 99.87%; CO production rate, 19.61 mmol h−1 gcat−1; and good cycling stability over 50 h). Detailed structural characterization studies and in situ DRIFTS measurements revealed that FeO in the FeCe-300 catalyst efficiently promoted the photothermal RWGS reaction, thus accounting for the very high selectivity to CO. FeCe-x catalysts prepared at higher reduction temperatures contained both FeO and Fe0, the latter catalyzing the Sabatier reaction to CH4 and thus lowering the selectivity of CO2 hydrogenation to CO. This work identifies the photothermal RWGS reaction as a new approach for harnessing solar energy to selectively produce CO from CO2 under mild reaction conditions.


  1. 1.

    Wei, J. et al. Directly converting CO2 into a gasoline fuel. Nat. Commun. 8, 15174 (2017).

    Article  Google Scholar 

  2. 2.

    Zhang, J. et al. Hydrogenation of CO2 into aromatics over a ZnCrOx-zeolite composite catalyst. Chem. Commun. (Camb.) 55, 973–976 (2019).

    CAS  Article  Google Scholar 

  3. 3.

    Jelle, A. A. et al. Highly efficient ambient temperature CO2 photomethanation catalyzed by nanostructured RuO2 on silicon photonic crystal support. Adv. Energy Mater. 8, 1702277 (2018).

    Article  Google Scholar 

  4. 4.

    Gao, P. et al. Direct conversion of CO2 into liquid fuels with high selectivity over a bifunctional catalyst. Nat. Chem. 9, 1019–1024 (2017).

    CAS  Article  Google Scholar 

  5. 5.

    Pan, Y. et al. Design of single-atom Co-N5 catalytic site: a robust electrocatalyst for CO2 reduction with nearly 100% CO selectivity and remarkable stability. J. Am. Chem. Soc. 140, 4218–4221 (2018).

    CAS  Article  Google Scholar 

  6. 6.

    Zhao, Y. et al. Reductive transformation of layered-double-hydroxide nanosheets to Fe-based heterostructures for efficient visible-light photocatalytic hydrogenation of CO. Adv. Mater. 30, 1803127 (2018).

    Article  Google Scholar 

  7. 7.

    Xie, C. et al. Tandem catalysis for CO2 hydrogenation to C2-C4 hydrocarbons. Nano Lett. 17, 3798–3802 (2017).

    CAS  Article  Google Scholar 

  8. 8.

    Wang, L. et al. Hydrogen-treated mesoporous WO3 as a reducing agent of CO2 to fuels (CH4 and CH3OH) with enhanced photothermal catalytic performance. J. Mater. Chem. A 4, 5314–5322 (2016).

    CAS  Article  Google Scholar 

  9. 9.

    Wang, L. et al. Incorporating nitrogen atoms into cobalt nanosheets as a strategy to boost catalytic activity toward CO2 hydrogenation. Nat. Energy 2, 869–876 (2017).

    CAS  Article  Google Scholar 

  10. 10.

    Song, H. et al. Light-enhanced carbon dioxide activation and conversion by effective plasmonic coupling effect of Pt and Au nanoparticles. ACS Appl. Mater. Interfaces 10, 408–416 (2018).

    CAS  Article  Google Scholar 

  11. 11.

    Habisreutinger, S. N., Schmidt-Mende, L. & Stolarczyk, J. K. Photocatalytic reduction of CO2 on TiO2 and other semiconductors. Angew. Chem. Int. Ed. 52, 7372–7408 (2013).

    CAS  Article  Google Scholar 

  12. 12.

    Qiao, J., Liu, Y., Hong, F. & Zhang, J. A review of catalysts for the electroreduction of carbon dioxide to produce low-carbon fuels. Chem. Soc. Rev. 43, 631–675 (2014).

    CAS  Article  Google Scholar 

  13. 13.

    Gouet, A. et al. Study of the origin of the deactivation of a Pt/CeO2 catalyst during reverse water gas shift (RWGS) reaction. J. Catal. 226, 382–392 (2004).

    Article  Google Scholar 

  14. 14.

    Pakhare, D. & Spivey, J. A review of dry (CO2) reforming of methane over noble metal catalysts. Chem. Soc. Rev. 43, 7813–7837 (2014).

    CAS  Article  Google Scholar 

  15. 15.

    Liu, H. et al. Conversion of carbon dioxide by methane reforming under visible-light irradiation: surface-plasmon-mediated nonpolar molecule activation. Angew. Chem. Int. Ed. 54, 11545–11549 (2015).

    CAS  Article  Google Scholar 

  16. 16.

    Zhou, W. et al. Direct conversion of syngas into methyl acetate, ethanol, and ethylene by relay catalysis via the intermediate dimethyl ether. Angew. Chem. Int. Ed. 57, 12012–12016 (2018).

    CAS  Article  Google Scholar 

  17. 17.

    Zhao, B. et al. Direct transformation of syngas to aromatics over Na-Zn-Fe5C2 and hierarchical HZSM-5 tandem catalysts. Chem 3, 323–333 (2017).

    CAS  Article  Google Scholar 

  18. 18.

    Sun, F. M., Yan, C. F., Wang, Z. D., Guo, C. Q. & Huang, S. L. Ni/Ce-Zr-O catalyst for high CO2 conversion during reverse water gas shift reaction (RWGS). Int. J. Hydrog. Energy 40, 15985–15993 (2015).

    CAS  Article  Google Scholar 

  19. 19.

    Williamson, D. L., Herdes, C., Torrente-Murciano, L., Jones, M. D. & Mattia, D. N-Doped Fe@CNT for combined RWGS/FT CO2 hydrogenation. ACS Sustain. Chem. Eng. 7, 7395–7402 (2019).

    CAS  Article  Google Scholar 

  20. 20.

    Álvarez Galván, C. et al. Reverse water-gas shift reaction at the Cu/ZnO interface: influence of the Cu/Zn ratio on structure-activity correlations. Appl. Catal. B-Environ. 195, 104–111 (2016).

    Article  Google Scholar 

  21. 21.

    Liu, C., Cundari, T. R. & Wilson, A. K. Reaction mechanism of the reverse water-gas shift reaction using first-row middle transition metal catalysts L’M (M = Fe, Mn, Co): a computational study. Inorg. Chem. 50, 8782–8789 (2011).

    CAS  Article  Google Scholar 

  22. 22.

    Wang, L. C., Tahvildar Khazaneh, M., Widmann, D. & Behm, R. J. TAP reactor studies of the oxidizing capability of CO2 on a Au/CeO2 catalyst—a first step toward identifying a redox mechanism in the Reverse Wate-Gas Shift reaction. J. Catal. 302, 20–30 (2013).

    CAS  Article  Google Scholar 

  23. 23.

    Goguet, A., Meunier, F. C., Tibiletti, D., Breen, J. P. & Burch, R. Spectrokinetic investigation of reverse water-gas-shift reaction intermediates over a Pt/CeO2Catalyst. J. Phys. Chem. B 108, 20240–20246 (2004).

    CAS  Article  Google Scholar 

  24. 24.

    Roberts, G. W., Chin, P., Sun, X. & Spivey, J. J. Preferential oxidation of carbon monoxide with Pt/Fe monolithic catalysts: interactions between external transport and the reverse water-gas-shift reaction. Appl. Catal. B-Environ. 46, 601–611 (2003).

    CAS  Article  Google Scholar 

  25. 25.

    Daza, Y. A. & Kuhn, J. N. CO2 conversion by reverse water gas shift catalysis: comparison of catalysts, mechanisms and their consequences for CO2 conversion to liquid fuels. RSC Adv. 6, 49675–49691 (2016).

    CAS  Article  Google Scholar 

  26. 26.

    Bustamante, F. et al. High-temperature kinetics of the homogeneous reverse water-gas shift reaction. AIChE J. 50, 1028–1041 (2004).

    CAS  Article  Google Scholar 

  27. 27.

    Chen, C. S., Cheng, W. H. & Lin, S. S. Study of iron-promoted Cu/SiO2 catalyst on high temperature reverse water gas shift reaction. Appl. Catal. A-Gen. 257, 97–106 (2004).

    CAS  Article  Google Scholar 

  28. 28.

    Zhu, X., Huo, P., Zhang, Y.-p, Cheng, D.-g & Liu, C.-j Structure and reactivity of plasma treated Ni/Al2O3 catalyst for CO2 reforming of methane. Appl. Catal. B-Environ. 81, 132–140 (2008).

    CAS  Article  Google Scholar 

  29. 29.

    Li, Z. et al. Co-based catalysts derived from layered-double-hydroxide nanosheets for the photothermal production of light olefins. Adv. Mater. 30, 1800527 (2018).

    Article  Google Scholar 

  30. 30.

    Chen, G. et al. Alumina-supported CoFe alloy catalysts derived from layered-double-hydroxide nanosheets for efficient photothermal CO2 hydrogenation to hydrocarbons. Adv. Mater. 30, 1704663 (2018).

    Article  Google Scholar 

  31. 31.

    Meng, X. et al. Photothermal conversion of CO2 into CH4 with H2 over Group VIII nanocatalysts: an alternative approach for solar fuel production. Angew. Chem. Int. Ed. 53, 11478–11482 (2014).

    CAS  Article  Google Scholar 

  32. 32.

    Liu, L. et al. Sunlight-assisted hydrogenation of CO2 into ethanol and C2+ hydrocarbons by sodium-promoted Co@C nanocomposites. Appl. Catal. B-Environ. 235, 186–196 (2018).

    CAS  Article  Google Scholar 

  33. 33.

    Gamarra, D. & Martínez-Arias, A. Preferential oxidation of CO in rich H2 over CuO/CeO2: Operando-DRIFTS analysis of deactivating effect of CO2 and H2O. J. Catal. 263, 189–195 (2009).

    CAS  Article  Google Scholar 

  34. 34.

    Wang, Y. et al. Nanocasting synthesis of chromium doped mesoporous CeO2 with enhanced visible-light photocatalytic CO2 reduction performance. J. Hazard Mater. 372, 69–76 (2019).

    CAS  Article  Google Scholar 

  35. 35.

    Ju, T. J., Wang, C. H. & Lin, S. D. Insights into the CO2 deoxygenation to CO over oxygen vacancies of CeO2. Catal. Sci. Technol. 9, 2118–2124 (2019).

    CAS  Article  Google Scholar 

  36. 36.

    Yin, G. et al. Hydrogenated blue titania for efficient solar to chemical conversions: preparation, characterization, and reaction mechanism of CO2 reduction. ACS Catal. 8, 1009–1017 (2018).

    CAS  Article  Google Scholar 

  37. 37.

    Wang, L. et al. Selective hydrogenation of CO2 to ethanol over cobalt catalysts. Angew. Chem. Int. Ed. 57, 6104–6108 (2018).

    CAS  Article  Google Scholar 

  38. 38.

    Wang, F. et al. Active site dependent reaction mechanism over Ru/CeO2 catalyst toward CO2 methanation. J. Am. Chem. Soc. 138, 6298–6305 (2016).

    CAS  Article  Google Scholar 

Download references


The authors are grateful for financial support from the National Key Projects for Fundamental Research and Development of China (2018YFB1502002, 2017YFA0206904, 2017YFA0206900, 2016YFB0600901), the National Natural Science Foundation of China (51825205, 51772305, 51572270, U1662118, 21871279, 21802154), the Beijing Natural Science Foundation (2191002, 2182078, 2194089), the Strategic Priority Research Program of the Chinese Academy of Sciences (XDB17000000), the Royal Society-Newton Advanced Fellowship (NA170422), the International Partnership Program of Chinese Academy of Sciences (GJHZ1819, GJHZ201974), the Beijing Municipal Science and Technology Project (Z181100005118007), and the K. C. Wong Education Foundation. The XAFS experiments were conducted on the 1W1B beamline of the Beijing Synchrotron Radiation Facility (BSRF). G.I.N.W. acknowledges funding support from the Energy Education Trust of New Zealand, the MacDiarmid Institute for Advanced Materials and Nanotechnology, the Dodd Walls Centre for Photonic and Quantum Technologies, and the University of Auckland Faculty Research Development Fund.

Author information



Corresponding author

Correspondence to Tierui Zhang.

Ethics declarations

Conflict of interest

The authors declare that they have no conflict of interest.

Additional information

Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary information

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Zhao, J., Yang, Q., Shi, R. et al. FeO–CeO2 nanocomposites: an efficient and highly selective catalyst system for photothermal CO2 reduction to CO. NPG Asia Mater 12, 5 (2020).

Download citation

Further reading


Quick links