Either in bulk form, or in atomically thin crystals, layered transition metal dichalcogenides continuously reveal new phenomena. The latest example is 1T’-WTe2, a semimetal found to exhibit the largest known magnetoresistance in the bulk, and predicted to become a topological insulator in strained monolayers. Here we show that reducing the thickness through exfoliation enables the electronic properties of WTe2 to be tuned, which allows us to identify the mechanisms responsible for the observed magnetotransport down to the atomic scale. The longitudinal resistance and the unconventional magnetic field dependence of the Hall resistance are reproduced quantitatively by a classical two-band model for crystals as thin as six monolayers, whereas a crossover to an Anderson insulator occurs for thinner crystals. Besides establishing the origin of the magnetoresistance of WTe2, our results represent a complete validation of the classical theory for two-band electron-hole transport, and indicate that atomically thin WTe2 layers remain gapless semimetals.
Semimetallic compounds are known to often exhibit many unusual electronic properties, including a non-saturating magnetoresistance (MR) with values among the largest ever reported1,2,3,4,5,6,7,8. Different theoretical scenarios—based on charge inhomogeneity1,3, spin–orbit interaction5, or the linear dispersion relation of charge carriers2,5,7,8 have been proposed in the past to explain such a large MR, but finding experimental evidence to conclusively establish their relevance for experiments has proven extremely difficult. The problem has resurfaced recently with the discovery of a record-high MR in semimetallic9,10 bulk 1T’-WTe2 (ref. 6), which was suggested to originate from the classical magnetotransport properties of two, nearly perfectly compensated electron and hole bands. The results of even more recent quantum oscillations11,12,13,14 and angle resolved photoemission (ARPES)15,16 measurements, however, suggest that more than two bands are present at the Fermi level, and cast doubts about the validity of this conclusion.
To address this issue, we have investigated magnetotransport through exfoliated WTe2 crystals and explored the properties of this material from bulk crystals all the way to atomically thin layers. We find that in all cases—for thicknesses down to six monolayers—the measured longitudinal and transverse MR can be reproduced with remarkable accuracy by a classical two-band model describing simultaneous electron and hole transport. For smaller thicknesses, the transport properties of WTe2 crystals change, and for crystals that are four monolayer or thinner we observe a transition to an insulating state. This insulating state occurs concomitantly with a qualitative change in the magentotransport properties that become fully dominated by quantum interference effects. All the observed phenomenology indicates that the insulating state originates from Anderson localization caused by an enhanced scattering at the outermost (surface) layer of the material, degraded by exposure to air. This finding implies that even down to the ultimate atomic thickness the WTe2 crystals remain un-gapped semimetals.
Magnetotransport of WTe2 in terms of a two-band model
According to theory17,18, classical magnetotransport in a two-band nearly compensated semimetal is described by the following expressions for the longitudinal and transverse resistivity ρxx(B) and ρxy(B) (where n, p, μe and μh are electron and hole densities and mobility and B is the magnetic field):
so that the MR is given by:
The regime of near compensation corresponds to having n sufficiently close to p so that the B2 term in the denominator of equations (1)–(3), , can be neglected in the magnetic field range explored in the experiments (that is, for all values of B in the measurements). In this case, the MR increases quadratically without saturation, , which is why this scenario was originally invoked to explain the behaviour of WTe2 (ref. 6). What is peculiar in this regime is the behaviour of the Hall resistivity ρxy(B): it is proportional to B at low field and to B3 at high field, with the magnitude and sign of the proportionality coefficients of both terms depending sensitively on the relative values of n, p, μe and μh. For nearly compensated systems, small relative changes in p and n (or in μe and μh) can then lead to dramatic changes in the behaviour of ρxy(B), so that—if the values of the system parameters n, p, μe and μh can be tuned experimentally—monitoring the evolution of ρxy(B) allows the validity of the proposed scenario to be proven (or disproven) unambiguously. However, virtually no effort has been devoted so far to investigating ρxy(B) on changing the system parameters, largely because of the experimental difficulties involved in controlling and determining unambiguously p, n, μe and μh.
WTe2 is rather unique in this regard because the material is layered (see Supplementary Fig. 1 for the crystal structure), and the system parameters can be varied by changing the material thickness through a simple exfoliation process. In addition, for WTe2 the comparison between experiment and theory is facilitated by the possibility to extract accurate estimates for the parameters directly from the experiments, which drastically narrows down the parameter range when fitting equations (1)–(3), , to the data. We start with the analysis of magnetotransport of bulk crystals. Figure 1a,b shows—as reported in recent earlier studies6,11,12,13,14—that the relative MR exhibits a large, non-saturating quadratic dependence on B, and that Shubnikov–de Haas (SdH) oscillations are clearly visible (for B≳3 T). The oscillation spectrum exhibits four independent frequencies ranging from ∼90 to 170 T, whose attribution to different families of charge carriers has not yet been conclusively established11,12,13,14. We follow ref. 12 and assume that the Fermi surface is approximately ellipsoidal with a circular cross-section in the plane perpendicular to B, which enables us to extract the value of the Fermi momentum kF and estimate the density of carriers (whose value depends on the assumed degree of anisotropy of the ellipsoidal Fermi surface; see ref. 12 for details). This estimate serves to fix the starting values of n and p that we use in fitting the data with equations (1)–(3), , . From the analysis of the SdH oscillations we also extract fairly precise estimates for μe and μh: the value of B at which the SdH oscillations appear fixes the mobility of one type of charge carriers through the condition μB∼1; the mobility for the other carrier type can then be estimated from the magnitude of the quadratic MR, (determining which type of charge carriers has one or the other mobility value requires the full data analysis).
Starting from the estimated values of n, p, μe and μh, we perform a fully quantitative fit of the experimental data to equations (1)–(3), , . The outcome of the fitting procedure is represented in Fig. 1a,c (see also the inset) with red dashed-dotted lines, for both ρxx(B) and ρxy(B). We obtain an excellent agreement between measurements and theory with values of parameters that are very close to our initial ‘rough’ estimates (for the electron and hole density, the final values are typically within a factor of two of the initial guesses or better, except for very thin layers, in which the SdH oscillations are weak; for the mobility values the deviation between initial guesses and final values is typically around 30%). The agreement between theory and data is particularly remarkable and compelling for ρxy(B): this quantity is ‘independent’ of the measurements used for the initial estimate of the model parameters (that is, ρxy(B) was not used to estimate the values of the parameters), and yet the analysis fully reproduces at a qualitative and quantitative level the extremely unconventional behaviour observed experimentally. As shown in the inset of Fig. 1c, theory even reproduces correctly the change in sign of ρxy(B) as a function of B, whose observation has never been previously reported in a semimetal. As equation (2) predicts the zero crossings to occur at , this observation imposes a tight quantitative constraint on the model parameters. It is the unique nature of the behaviour observed experimentally, together with the excellent agreement between data and equations (1)–(3), , , that allow us to conclude unambiguously that a nearly compensated two-band model in the classical regime explains the magnetotransport properties of WTe2.
Thickness evolution of classical magnetotransport
By following the procedure established for macroscopic crystals, we extend our investigations to layers of increasingly smaller thickness, which enables us to explore whether WTe2 behaves as a compensated two-band semimetal even when its thickness is reduced to the atomic scale19,20. Transport measurements were performed on devices nanofabricated on exfoliated flakes whose thickness was determined—all the way to individual monolayers—through a careful analysis relying on Raman spectroscopy21,22,23, optical contrast measurements and atomic force microscopy (see Supplementary Note 1 and Supplementary Figs 2–4). Figure 2a shows the MR of exfoliated crystals with thickness down to six monolayers, together with the results (red dashed-dotted lines) of the quantitative fitting to equations (1)–(3), , . In all cases, we find that theory fully reproduces all quantitative and qualitative aspects of the data for both ρxx(B) and ρxy(B) (see Fig. 2a,c; clearly, the SdH oscillations that are superimposed on the classical longitudinal and transverse resistivity are of quantum origin and are therefore not reproduced by the classical theory). On varying the thickness, the longitudinal MR always exhibits a B2 dependence, whereas the functional dependence of ρxy(B) varies very considerably (presence or absence of non-monotonicity, strength of the non-linearity, concavity/convexity of the curve and so on.). This rich behaviour—very precisely reproduced by equation (2)—is a manifestation of the changes in sign (and magnitude) of the coefficients of the B-linear and B-cubic terms, determined by the relative magnitude of n and p, and of μe and μh.
The very systematic agreement between data and equations (1)–(3), , is quite remarkable in two important regards. Firstly, it represents a complete quantitative validation of the classical theory of transport for a nearly compensated semimetal with an electron and a hole band, at a notably high level of detail. Secondly, it shows that a two-band nearly compensated semimetal model does reproduce the magnetotransport properties of WTe2 very satisfactorily in a way that is insensitive to the precise details of the material band structure, which on the energy scale of the band overlap—few tens of meV—is certainly different for the bulk and for crystals that are only six or seven monolayer thick. This insensitivity to details is very likely the reason why a two-band model works so well, despite the presence of more bands, as clearly indicated from SdH oscillations and ARPES measurements. It strongly suggest that electrons (and holes) in different bands have essentially the same mobility, so that classical transport is only sensitive to their total density (and not to the density in each one of the bands). Indeed, if we compare the compensation level n/p that we extract from classical transport with values reported earlier, inferred from the total electron and hole density obtained from the SdH oscillations frequencies12,13 or ARPES15,16 measurements in bulk crystals, we find a satisfactory agreement.
As it is apparent from the quality of the agreement between equations (1)–(3), , and the data, the ability to reproduce different qualitative features with a same functional dependence allows all parameters in the model to be extracted precisely. Figure 2d–f summarize the evolution of n, p, μe and μh with decreasing thickness, which allows the identification of several trends. Bulk crystals with thickness on the mm scale (that is, samples B15 and B16) exhibit only small sample-to-sample fluctuations in electron and hole density and mobility: both electron and hole mobility values are rather large (between 5,000 and 10,000 cm2 V−1 s−1) and compensation between electrons and holes is nearly perfect (n/p∼1.1). As the layers are thinned down μe and μh decrease, because the crystal thickness becomes smaller than the mean free path and scattering at the surface becomes relevant. Nevertheless, even for the thinnest layers analysed—only six or seven-layer thick—μe and μh∼1,000 cm2 V−1 s−1. The electron and hole densities n and p exhibit reproducible variations as a function of thickness (the minimum in n seen in Fig. 2e, for instance, has been found in the other crystals measured, having thickness between 30 and 50 nm). The origin of these variations is likely the consequence of different physical phenomena, whose relevance depends on the thickness range considered (such as strain for crystals that are several tens of nanometres thick, and the effect of charge transfer from the surface for thinner layers). The net result is that the compensation level worsens for thinner layers and the data show that n/p ranges from ∼0.7 to 1.5 as the thickness is reduced from bulk crystals to crystals that are only seven-layer thick. The dependence of ρxx(B) remains, nevertheless, quadratic throughout the magnetic field range of our measurements, implying that , so that even thin layers still fall in the theoretical regime characteristic of nearly compensated semimetals. The magnitude of the MR is, however, very significantly suppressed, mainly because of the large drop in carrier mobility. We conclude that, although having comparable values for the density of electrons and holes is important, it is the high mobility of the two carriers that is essential to achieve the very large MR measured in WTe2.
Metal-to-insulator transition in thin WTe2 flakes
As the thickness of WTe2 is decreased even further to approach the ultimate limit of individual monolayers, the transport regime of WTe2 changes qualitatively. The change manifests itself in a metal–insulator transition clearly visible in the temperature dependence of the conductivity, as shown in Fig. 3a. Interestingly, normalizing to the number of layers, we find that the transition occurs when the conductivity per layer is ∼e2/h. WTe2 crystals that are four-layer thick are on the insulating side of the transition—albeit just barely—and the insulating temperature dependence of the conductivity becomes progressively more pronounced for tri and bilayers (we have also fabricated monolayer devices and found that their conductance is unmeasurably low). In all cases, the observed insulating behaviour sets in only at relatively low temperature so that, whereas, the room temperature resistivity increases by only a factor of five when comparing bulk crystals and bilayers, the increase is as large as five orders of magnitude at T=250 mK.
Identifying the origin of the insulating state is important to fully understand the properties of WTe2 down to the ultimate atomic scale. For crystals only a few monolayers thick, changes in the band structure may reduce the overlap between conduction and valence bands, eventually leading to the opening of a band gap, a scenario that would account for the observed metal–insulator transition. Such an explanation, however, does not seem consistent with the experimental results. The analysis of magnetotransport, for instance, shows that the density of electrons and holes does not change significantly on thinning down the material. If anything, the electron density increases, whereas, a decrease in band overlap—and the opening of a small gap—should cause the opposite effect. In addition, the square conductance G□ measured in tri and four-layer WTe2 increases steadily with increasing gate voltage VG (see Fig. 3b), showing no sign of the non-monotonic dependence expected for ambipolar conduction normally observed in the presence of a small band gap. On contrary, the G□(VG) dependence is consistent with the behaviour expected if both types of charge carriers are present, with electrons having a mobility 2-to-3 times larger than the holes (that is, the same behaviour seen in crystals that are 6-to-12 monolayer thick, see Fig. 2e). In this case, we can estimate μe for trilayers and four layers, by applying the relation (with C gate capacitance per unit area) to extend our estimates of carrier mobility; we find μe∼25 cm2 V−1 s−1 and μe∼5 cm2 V−1 s−1 in the two cases. These values, one-to-two orders of magnitude smaller than those found in the thinnest multilayers that still exhibit metallic behaviour (see Fig. 2e), indicate rather unambiguously that the insulating state originates from an increase in disorder strength. Indeed, our observation that the crossover from metallic to insulating behaviour occurs when the conductivity per layer is ∼e2/h strongly suggests that carriers in very thin WTe2 layers are Anderson localized.
Quantum correction to the magnetoconductivity
To find additional experimental evidence supporting the tendency of charge carriers towards localization, we look at magnetotransport measurements of WTe2 crystals that are four layers or thinner. The emergence of quantum corrections to the conductivity in the low temperature MR data—superimposed on the quadratic classical background—becomes clearly apparent as the material thickness is decreased below 10 layers (see Fig. 4a). The phenomenon is known as weak antilocalization (WAL) and originates from the interference of quantum coherent electronic waves undergoing diffusive motion in the presence of spin–orbit interaction, which in WTe2 is large due to the large atomic number of tungsten. The relative strength of the effect increases as the layer thickness is decreased, because the magnitude of the WAL contribution on the conductivity is always ∼e2/h, whereas the classical contribution decreases on thinning down the material (to illustrate this point more clearly, in the Supplementary Fig. 5 the quantum correction signal is shown separately, after subtracting the classical contribution from the measured conductivity; see Supplementary Note 2 for more details). Note also that the magnetic field range in which WAL is visible becomes larger with decreasing thickness, as expected, because thinner flakes have smaller mobility and hence shorter electronic mean free path. Quantum interference effects eventually entirely dominate the MR of crystals thinner than four layers—the same thickness for which the insulating temperature dependence of the conductivity is first observed—that do not any more exhibit the quadratic B dependence expected from equations (1)–(3), , . We conclude that, in passing through the metal–insulator transition, the MR of WTe2 changes qualitatively, and its behaviour is determined by quantum—and not any more classical—processes. The absolute magnitude of the quantum magnetoconductance at T=250 mK is ∼e2/h and it decreases on increasing the temperature (see Fig. 4b), as qualitatively expected for the WAL correction to the conductivity.
Even though the precise nature of the spin–orbit interaction responsible for spin flip cannot be determined from the measurements, we attempt a semi-quantitative analysis of the data by fitting to Hikami–Larkin–Nagaoka theory for WAL, whose expression for the magnetoconductance reads24:
where Ψ is the digamma function, is determined by the electron phase coherence time τφ and the diffusion constant D, and is determined by the spin relaxation time τso. Figure 4b shows that the agreement between measurements performed on trilayer WTe2 and theory is remarkably good. To fit the data we allow Bφ to vary as a function of temperature (as shown in Fig. 4c), and keep Bso constant (6 T), as expected from the physical meaning of these parameters (Bφ is proportional to the inverse of phase coherence time , and the approximately linear T dependence of Bφ is consistent with dephasing induced by electron–electron interactions in a diffusive system25). Irrespective of the precise values extracted for the parameters, which may depend on the specific theory of WAL used to fit, the agreement between equation (4) and the experimental data (as well as the internal consistency of the behaviour observed experimentally) confirm that in WTe2 crystals that are only a few layers thick localization effects dominate. Our results therefore show that—albeit localized—carriers are still present at the Fermi energy. This confirms the results of theoretical calculations19,20 that indicates how WTe2 remains as a gapless semimetal all the way down to monolayer thickness.
The increase in disorder that is responsible for the occurrence of Anderson localization in very thin WTe2 crystals originates from the non-perfect chemical stability of WTe2 in the presence of humidity. Such a non-perfect stability leads to a detectable change in colour and contrast (visible under an optical microscope, see Supplementary Note 3 and Supplementary Fig. 6) if thin crystals (<4 layers) are exposed to the environment for a sufficiently long time. It appears that between one and two layers on each crystal face are affected by the degradation process during the time needed to nano-fabricate devices (that includes optical inspection to identify the crystals, spinning and backing the resist needed for electron-beam lithography to define the metal contacts, and performing the lift off process after the metal deposition). As compared with many other exfoliated materials that react chemically when exposed to air—such as phosphorene26,27,28,29 and NbSe2 (ref. 30), for which strong degradation is visible after 1 h of exposure to air—WTe2 seems to be considerably more stable. Significant degradation, giving optically visible signs, is only seen to occur after exposure to the environment for a day or longer periods.
As it has been demonstrated for highly air-sensitive materials, encapsulation27,28,29 (for example, in between two hBN layers) of WTe2 layers under controlled atmosphere will allow material degradation during the device fabrication process to be eliminated. On the basis of the analysis of transport presented in this paper, we anticipate that preserving the chemical integrity of the crystal surface will prevent the decrease in carrier mobility and will enable the realization of atomically thin layers possessing carrier mobility values comparable to those found in the bulk. Such an advance will have important consequences. In particular, it will drastically increase the magnitude of the MR in atomic scale crystals of WTe2 to the record values observed in the bulk. It will also make WTe2 fully gate tunable: since mono, bi and trilayers are sufficiently thin to vary their carrier density significantly with electrostatic gate electrodes, the realization of gated encapsulated devices will disclose the possibility to perform experiments that are impossible to perform in thicker, bulk-like crystals. Finally, we envision that it will be possible to induce and control strain in encapsulated monolayer WTe2 using techniques similar to those employed in graphene31. This will open the possibility to perform transport experiments to test whether strained monolayers of 1T’-WTe2 are two-dimensional topological insulators as recently predicted theoretically19.
WTe2 crystal growth
All transport measurements described in this paper have been performed on devices based on WTe2 crystals grown by means of chemical vapour transport using WCl6 as a transport agent, as discussed in more detail in the Supplementary Note 4.
For measurements on bulk samples, electrical contacts were made with silver epoxy directly on suitably chosen as-grown crystals. To investigate transport on thinner layers, flakes were exfoliated from bulk crystals using adhesive tape and transferred onto a Si substrate covered with 285 nm of SiO2, after which conventional nano-fabrication techniques (electron-beam lithography, metals evaporation and lift off) were employed to attach electrical contacts (consisting of Ti/Au bilayers, typically 10/70 nm thick). The thickness of the exfoliated crystals was identified by means of atomic force microscopy, optical contrast and Raman spectra as discussed in detail in the Supplementary Note 1. Throughout the process of crystal identification and device fabrication, care was taken to minimize exposure of the material to air to minimize degradation (the exfoliated crystals where stored in either a glove box with sub-p.p.m. concentration of oxygen and water, or in a high vacuum chamber, when not being processed).
All magnetotransport measurements were performed using either a Heliox 3He system (Oxford instruments) operated in a cryostat with a 14 T magnet and a base temperature of 250 mK, or a cryofree Teslatron cryostat with a 12 T magnet and a base temperature of 1.5 K. The measurements were performed in a current-bias configuration using lock-in amplifiers and home-made low-noise electronic current sources and voltage amplifiers.
How to cite this article: Wang, L. et al. Tuning magnetotransport in a compensated semimetal at the atomic scale. Nat. Commun. 6:8892 doi: 10.1038/ncomms9892 (2015).
Xu, R. et al. Large magnetoresistance in non-magnetic silver chalcogenides. Nature 390, 57–60 (1997).
Abrikosov, A. A. Quantum magnetoresistance. Phys. Rev. B 58, 2788–2794 (1998).
Parish, M. M. & Littlewood, P. B. Non-saturating magnetoresistance in heavily disordered semiconductors. Nature 426, 162–165 (2003).
Ishiwata, S. et al. Extremely high electron mobility in a phonon-glass semimetal. Nat. Mater. 12, 512–517 (2013).
Liang, T. et al. Ultrahigh mobility and giant magnetoresistance in Cd3As2: protection from backscattering in a Dirac semimetal. Nat. Mater. 14, 280–284 (2014).
Ali, M. N. et al. Large, non-saturating magnetoresistance in WTe2 . Nature 514, 205–208 (2014).
Chandra, S. et al. Extremely large MR and ultrahigh mobility in the topological Weyl semimetal NbP. Nat. Phys. 11, 645–649 (2015).
Zhang, C. et al. Tantalum monoarsenide: an exotic compensated semimetal. Preprint at http://arxiv.org/abs/1502.00251 (2015).
Kabashima, S. Electrical properties of tungsten-ditelluride WTe2 . J. Phys. Soc. Jpn 21, 945–948 (1966).
Mentzen, B. F. & Sienko, M. J. Preparation and x-ray study of mixed-anion tungsten dichalcogenides. Inorg. Chem. 15, 2198–2202 (1976).
Cai, P. L. et al. Drastic pressure effect on the extremely large magnetoresistance in WTe2: a quantum oscillation study. Phys. Rev. Lett. 115, 057202 (2015).
Zhu, Z. et al. Quantum oscillations, thermoelectric coefficients, and the fermi surface of semimetallic WTe2 . Phys. Rev. Lett. 114, 1–5 (2015).
Rhodes, D. et al. Role of spin-orbit coupling and evolution of the electronic structure of WTe2 under an external magnetic field. Phys. Rev. B 92, 125152 (2015).
Zhao, Y. et al. Anoisotropic MR and exotic longitudianl linear MR in WTe2 crystals. Phys. Rev. B 92, 041104(R) (2015).
Pletikosić, I., Ali, M. N., Fedorov, a. V., Cava, R. J. & Valla, T. Electronic structure basis for the extraordinary magnetoresistance in WTe2 . Phys. Rev. Lett. 113, 1–5 (2014).
Xu, F. et al. Signature of strong spin orbital coupling in the large nonsaturating MR materials WTe2. Phys. Rev. Lett. 115, 166601 (2015).
Sondheimer, E. H. & Wilson, A. H. The theory of the magneto-resistance effects in metals. Proc. R. Soc. London Series A Math. Phys. Sci. 190, 435–455 (1947).
Murzin, S. S., Dorozhkin, S. I., Landwehr, G. & Gossard, A. C. Effect of hole-hole scattering on the conductivity of the two-component 2D hole gas in GaAs/(AlGa)As heterostructures. J. Exp. Theor. Phys. Lett. 67, 113–119 (1998).
Xiaofeng, Q. et al. Quantum spin Hall effect in two-dimensional transition metal dichalcogenides. Science 346, 1344–1347 (2015).
Lv, H. Y. et al. Perfect charge compensation in WTe2 for the extraordinary magnetoresistance: From bulk to monolayer. Europhys. Lett. 110, 37004 (2015).
Kong, W.-D. et al. Raman scattering investigation of large positive magnetoresistance material WTe2 . Appl. Phys. Lett. 106, 081906 (2015).
Jiang, Y. C. & Gao, J. Raman fingerprint of semi-metal WTe2 from bulk to monolayer. Preprint at http://arxiv.org/abs/1501.04898 (2015).
Jana, M. K. et al. A combined experimental and theoretical study of the electronic and vibrational properties of bulk and few layer Td WTe2. J. Phys. Condens. Matter 27, 285401 (2015).
Hikami, S., Larkin, A. I. & Nagaoka, Y. Spin-orbit interaction and magnetoresistance in the two dimensional random system. Prog. Theor. Phys. 63, 707–710 (1980).
Aleiner, I. L., Altshuler, B. L. & Gersheson, M. E. Interaction effects and phase relaxation in disordered systems. Waves Random Media 9, 201–239 (1999).
Li, L. et al. Black phosphorus field-effect transistors. Nat. Nanotechnol. 9, 372–377 (2014).
Wood, J. D. et al. Effective passivation of exfoliated black phosphorus transistors against ambient degradation. Nano Lett. 14, 6964–6970 (2014).
Avsar, A. et al. Air-stable transport in graphene-contacted, fully encapsulated ultrathin black phosphorus-based field-effect transistors. ACS Nano 9, 4138–4145 (2015).
Li, L., Yang, F., Ye, G. J., Zhang, Z. & Zhu, Z. Quantum Hall effect in black phosphorus two-dimensional electron gas. Nat. Nanotechnol. 10, 608–613 (2015).
Geim, a. K. & Grigorieva, I. V. Van der Waals heterostructures. Nature 499, 419–425 (2013).
Bao, W. et al. Controlled ripple texturing of suspended graphene and ultrathin graphite membranes. Nat. Nanotechnol. 4, 562–566 (2009).
We gratefully acknowledge A. Ferreira for technical support, and M. Gibertini and D. Ki for fruitful discussions. Financial support from the Swiss National Science Foundation and from the EU Graphene Flagship project is also acknowledged.
The authors declare no competing financial interests.
Supplementary Figures 1-6, Supplementary Notes 1-4 and Supplementary References. (PDF 894 kb)
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Wang, L., Gutiérrez-Lezama, I., Barreteau, C. et al. Tuning magnetotransport in a compensated semimetal at the atomic scale. Nat Commun 6, 8892 (2015). https://doi.org/10.1038/ncomms9892
This article is cited by
Para-hydrodynamics from weak surface scattering in ultraclean thin flakes
Nature Communications (2023)
Direct observation of vortices in an electron fluid
Growth of bilayer MoTe2 single crystals with strong non-linear Hall effect
Nature Communications (2022)
Terahertz response of monolayer and few-layer WTe2 at the nanoscale
Nature Communications (2021)
Van der Waals thin films of WTe2 for natural hyperbolic plasmonic surfaces
Nature Communications (2020)
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.