Abstract
The pursuit of better atomic clocks has advanced many research areas, providing better quantum state control, new insights in quantum science, tighter limits on fundamental constant variation and improved tests of relativity. The record for the best stability and accuracy is currently held by optical lattice clocks. Here we take an important step towards realizing the full potential of a manyparticle clock with a stateoftheart stable laser. Our ^{87}Sr optical lattice clock now achieves fractional stability of 2.2 × 10^{−16} at 1 s. With this improved stability, we perform a new accuracy evaluation of our clock, reducing many systematic uncertainties that limited our previous measurements, such as those in the lattice ac Stark shift, the atoms’ thermal environment and the atomic response to roomtemperature blackbody radiation. Our combined measurements have reduced the total uncertainty of the JILA Sr clock to 2.1 × 10^{−18} in fractional frequency units.
Introduction
Precise and accurate optical atomic clocks^{1,2,3,4,5} have the potential to transform global timekeeping, enabling ordersofmagnitude improvements in measurement precision and sensor resolution for a wide range of scientific and technological applications. The pursuit of better atomic clocks has also had strong impact on many fundamental research areas, providing improved quantum state control^{6,7}, deeper insights in quantum science^{8,9}, tighter limits on fundamental constant variation^{10,11} and enhanced sensitivity for tests of relativity^{12}. Techniques developed for optical atomic clocks, such as advanced laser stabilization^{13,14}, coherent manipulation of atoms^{15} and novel atom trapping schemes^{16}, have given rise to new research opportunities in quantum physics.
The continued advances in clock stability and accuracy go hand in hand. In an optical atomic clock, shortterm stability originates from an ultrastable laser that serves as a local oscillator. Clock stability can be extended from seconds to hours by referencing the ultrastable laser to a highqualityfactor optical transition of an atom^{17}. In this work, we use an ultrastable laser with 10 s coherence time, referenced at 60% duty cycle to thousands of strontium atoms in an optical lattice, to achieve a record fractional frequency stability of 2.2 × 10^{−16} at 1 s.
Better clock stability allows for faster evaluations of systematic uncertainties and enables the discovery of new physical effects^{18}. Here we describe a set of innovations implemented to improve the accuracy of the ^{87}Sr clock: an optical lattice with no measurable ac Stark shift at 1 × 10^{−18}, blackbody radiation (BBR) thermometry with millikelvin level accuracy, atomic structure measurements that characterize the atomic response to BBR and active servo stabilization of electric and magnetic fields. With these developments, we achieve an overall systematic uncertainty of 2.1 × 10^{−18}, which is more than a threefold improvement over the previous best atomic clock^{1}. This corresponds to a gravitational redshift for a height change of 2 cm on Earth.
Results
Clock stability
After preparing ultracold strontium atoms in an optical lattice (see Methods), we probe the ^{1}S_{0}→^{3}P_{0} 1 mHz clock transition with a 698nm laser stabilized to 26 mHz^{14}. The laser frequency offset from the clock transition is determined with Rabi spectroscopy, with lineshapes shown for 1 and 4 s probe times in Fig. 1a. For longer probe times, atomic interactions affect the measured linewidth^{18}. Here we use Fourierlimited probe times (≤1 s) to study the clock stability and systematics. The clock transition is probed once on each side of the resonance centre; the difference in excited state fraction between these two measurements provides the error signal used to lock the laser to the clock transition.
Our clock stability at short averaging times is limited by the Dick effect^{19}—aliased highfrequency noise of the clock laser—that surpasses quantum projection noise^{20} with 2,000 atoms. At long averaging times, the only mechanism that can limit the stability is drifting systematic shifts. We have demonstrated that after careful control of systematic effects, residual drifts did not affect clock stability at 2 × 10^{−18} after thousands of seconds of averaging time^{1}. Furthermore, stability data taken over the course of a month was robust and repeatable.
With longterm drift under control at the low 10^{−18} level, we can obtain a complete characterization of the clock stability with shortterm stability measurements. Both the quantum projection noise and the Dick effect have been confirmed to be correctly determined with a selfcomparison, which agrees with the measurement from a twoclock comparison^{21}. A selfcomparison approach compares two independent frequency locks operating on alternate experimental cycles^{22}. Unlike synchronous stability^{5,21}, which is useful for systematic evaluations but which does not demonstrate how a system would perform as an independent frequency standard, a selfcomparison reproduces the shortterm stability of an independent clock.
Taking this approach, we use 1s probe pulses to achieve the best independent clock stability of 2.2 × 10^{−16}/τ^{1/2}, where τ is the averaging time in seconds (red solid line in Fig. 1b). This is consistent with our estimate of the Dick effect based on the known laser noise spectrum^{14}. We now reach 1 × 10^{−17} stability in <500 s, in contrast to the previous record of 1,000 s (blue dashed line in Fig. 1b)^{1,3,21}.
This improved stability motivates the implementation of new strategies to reduce systematic uncertainties. Table 1 provides an uncertainty budget for our clock. We measure many of these uncertainties with lockin detection, which involves modulating one parameter of our experiment between two values and recording the resulting frequency shift of the clock transition^{1,22}. We present some of the important systematic shifts that are measured using lockin detection, such as the lattice ac Stark and background dc Stark shifts. We also discuss two advances that reduce the BBR shift uncertainty: improved radiation thermometry and a direct measurement of the ^{3}D_{1} state lifetime to determine the atomic spectral response to BBR.
Lattice ac Stark shift
The lattice ac Stark shift is measured by performing lockin detection of the frequency shift between different lattice intensities. Atoms are confined in an optical lattice with a tight trapping potential that eliminates Doppler and recoil shifts during clock spectroscopy. A magic wavelength optical trap^{16,23,24} induces identical ac Stark shifts for the two clock states, making the clock transition frequency independent of the intensity of the optical trap.
The differential ac Stark shift of the two electronic clock states Δν_{ac} is given by^{25},
where and are the lattice polarization and propagation vectors, respectively, ξ is the lattice polarization ellipticity (0 indicates linear polarization), is the bias magnetic field direction, which defines the quantization axis, f is the lattice laser frequency, U_{0} is the trap depth, and Δκ_{s}, Δκ_{v} and Δκ_{t} are the differential scalar, vector, and tensor shift coefficients, respectively. In our onedimensional optical lattice geometry, we reduce sensitivity to drifts by aligning the bias magnetic field, the lattice light polarization and the clock laser polarization (ξ=0, , ), as well as independently stabilizing the magnetic field^{1}. To remove any residual vector Stark shift, we probe the stretched m_{F}=±9/2 spin states and average their transition frequencies^{26}.
By varying both the lattice wavelength and U_{0}, we find the magic wavelength for m_{F}=±9/2, where the scalar and tensor components of the differential Stark shift cancel^{27,28} (Fig. 2b), and we operate our lattice there. The lattice laser is locked to an optical frequency comb that is referenced to the National Institute of Standards and Technology (NIST) Boulder hydrogen maser. Our operating wavelength is c/(368.5544849(1) THz), where c is the speed of light. Here we measure an ac Stark shift of (−1.3±1.1) × 10^{−18} for a trap depth of 12 μK, or 71 times the lattice photon recoil energy. At this lattice wavelength we do not observe a change in the clock frequency with lattice depth (Fig. 2a, open circles), in contrast to our previous measurement (Fig. 2a, open squares). We applied a linear fit to the data, because an Ftest did not justify adding a term that is nonlinear in U_{0} (see Methods).
Modulating the lattice depth changes the sample density, potentially adding a parasitic density shift. We account for this by employing density shift cancellation^{1} based on the experimentally verified relation that the density shift is proportional to NU_{0}^{3/2}, where N is the atom number. As U_{0} is modulated, N is correspondingly changed and monitored to ensure commonmode cancellation of the density shift.
Dc Stark shift
The dc Stark shift is an important systematic effect that has been measured in lattice clocks^{1,27,29}. Here we demonstrate active control of the dc Stark along the axis that was found to have a measureable background field. Electrodes placed outside the vacuum chamber allow us to apply an external electric field and change its direction. As the dc Stark shift is proportional to the square of the total electric field, a background field leads to a frequency difference when we reverse the applied field direction. This frequency difference, which is linearly proportional to the background electric field magnitude, serves as an error signal that is processed by a digital loop filter, which controls the electrode voltages to cancel the background Stark shift. This active servo, operated under a 0.1Hz sampling rate, nulls the dc Stark shift with 1 × 10^{−19} uncertainty.
Radiation thermometry
The largest systematic uncertainty in our clock comes from the Stark shift Δν_{BBR} due to the background BBR field^{30,31}. Δν_{BBR} can be approximated as,
where T is the ambient temperature, T_{0}=300 K, ν_{stat} and ν_{dyn} are the static and dynamic coefficients, respectively, which describe the atomic response to ideal BBR, and higher order terms are negligible^{32}. The static shift scales as T^{4}, because it is proportional to the total energy contained in the BBR electric field. The dynamic shift comes from coupling to atomic transitions out of the clock states that spectrally overlap with room temperature BBR and it is sensitive to deviations from an ideal BBR spectrum. As ν_{stat} has already been accurately determined^{32}, the systematic uncertainty in Δν_{BBR} comes from ν_{dyn} and T. Although the dynamic term accounts for only 7% of the total BBR shift, uncertainty in ν_{dyn} is the dominant source of BBR shift uncertainty^{1}.
We measure the BBR environment of the atoms with thinfilm platinum resistance thermometers^{33} (PRTs), which are selected for good stability when thermally cycled over a test interval of 200 °C. Two PRTs (primary sensors) are painted black to increase radiative coupling and mounted to the ends of glass tubes sealed to vacuum flanges. Electrical feedthroughs allow for fourwire measurements (Fig. 3a). The PRTs are calibrated on their mounts at the NIST Sensor Science Division temperature calibration facilities in Gaithersburg. Calibration is accomplished using Standard Platinum Resistance Thermometers traceable to the NIST ITS90 temperature scale and a water comparison bath. When there are temperature gradients across the mounting structures, heat that conducts from the flanges to the sensors (known as ‘immersion error’) biases the BBR temperature measurements. To calibrate the bias, we embed a pair of secondary NISTcalibrated PRTs in the vacuum flanges (flange sensors) to measure these gradients. As a function of an applied gradient, we compare the primary sensor resistance in vacuum (R_{vacuum}), when the parasitic conductance is substantial, to the primary resistance in helium (R_{He}), when the parasitic conductance is negligible (see Fig. 3b and Methods). After calibration, the sensors were returned under vacuum to JILA and installed in the clock vacuum chamber, where we observe that residual gradients in the clock chamber are very small and immersion errors are negligible.
Only in an inhomogeneous thermal environment do emissivities play a role in determining the dynamic BBR shift. Therefore, to predict the dynamic BBR shift correctly from the sensor resistance, we must ensure that the atoms are in a sufficiently thermal BBR environment. This is accomplished by surrounding the clock vacuum chamber with a BBR shield that achieves ≤1 K spatial temperature inhomogeneity (Fig. 3a). One sensor is moveable and it measures a 1.5mK temperature difference between the atom location and a retracted position 2.5 cm away. Accounting for our vacuum chamber emissivities and geometry, this small temperature gradient confirms a correction of <1 × 10^{−19} to the clock uncertainty due to a nonthermal spectrum^{1} (see Methods).
The final temperature uncertainties of the movable and fixed sensors are 5 and 11 mK, respectively. The agreement between the moveable and fixed sensors (Fig. 3c), which have markedly different immersion error coefficients (Fig. 3b), further ensures that the gradients in the clock chamber are small and supports the conclusion that no calibration shifts occurred during transport and installation. Using the movable sensor, with uncertainty summarized in Table 2, we reach an uncertainty of 3 × 10^{−19} in the static BBR shift. This approach allows us to operate the clock at room temperature while achieving a similar uncertainty to invacuum radiationshielded lattice clocks at cryogenic^{5} or room temperatures^{34}.
^{3}D_{1} decay rate
We now discuss our largest systematic uncertainty, which arises from the BBR dynamic coefficient ν_{dyn}. The dominant source of uncertainty in ν_{dyn} comes from that of the oscillator strength of the 2.6 μm transition from the 5s5p^{3}P_{0} clock state to the 5s4d^{3}D_{1} state^{30,32}. This is the only transition from a clock state that overlaps significantly in frequency with the room temperature BBR spectrum. According to ref. 30, an accurate measurement of the 5s4d^{3}D_{1} state lifetime τ_{3D1} will improve the ν_{dyn} accuracy. As shown in Fig. 4a, we first use our clock laser to drive the ^{1}S_{0}→^{3}P_{0} transition and then use a 2.6μm distributedfeedback laser to drive the ^{3}P_{0}→^{3}D_{1} transition with a 200ns pulse. The atoms decay from the ^{3}D_{1} state into the ^{3}P manifold^{35}. Those that decay into the ^{3}P_{1} state then decay to the ^{1}S_{0} state, spontaneously emitting a 689nm photon that is collected on a photomultiplier. A photon counter time bins the data and we fit it to a double exponential function^{35} to extract τ_{3D1} and the ^{3}P_{1} lifetime τ_{3P1} (Fig. 4b).
We use the fit function y(t)=y_{0}+A{exp[–(t–t_{0})/τ_{3P1}]–exp[–(t–t_{0})/τ_{3D1}]}, where t_{0} is the time offset, y_{0} is the background counts and A is the amplitude. This functional form is valid after the 200ns excitation pulse is extinguished as long as t_{0} is a free fit parameter. Both an analytical model and a numerical simulation confirm that this functional form gives an unbiased fit. Another potential concern is densitydependent effects^{35} such as radiation trapping and superradiance. However, as shown in Fig. 4c, we vary the density and observe no statistically significant density dependence of τ_{3D1}. From our result of τ_{3D1}=(2.18±0.01) μs, we determine ν_{dyn}=(−148.7±0.7) mHz, improving the uncertainty in ν_{dyn} by a factor of 2 and agreeing with refs. 30, 32. As shown in Table 3, this measurement is limited by statistical error. The dynamic BBR uncertainty is reduced to 1.4 × 10^{−18}. We also improve the uncertainty of the ^{3}P_{1} lifetime by an order of magnitude, finding τ_{3P1}=(21.28±0.03) μs.
Finally, we have greatly reduced the uncertainties in the first and secondorder Zeeman shifts and the probe Stark shift to the low 10^{−19} level or better (see Methods).
Discussion
The current generation of stable lasers with >10 s coherence time and manyparticle clocks have ushered in a new era of clock accuracy near the 1 × 10^{−18} level. Even now, this coherence time has opened the possibility to eliminate the Dick effect by alternatively interrogating two separate atomic samples at >50% duty cycle with a single laser^{36,37}. Soon, the next generation of ultrastable lasers will come online^{13,38}, with coherence times rivaling that of the 160s natural lifetime of the Sr clock transition. The enhanced stability will not only bring clock accuracy to a new level, but also set the stage for quantum metrology where quantum correlations will be harnessed to advance the frontier of measurement precision beyond the standard quantum limit^{39,40,41,42}.
Methods
Sample preparation
We first laser cool a hot strontium beam to 1 mK using a Zeeman slower and threedimensional magnetooptical trap (MOT) on the ^{1}S_{0}→^{1}P_{1} 32 MHz transition at 461 nm. The atoms are further cooled to a few μK with a threedimensional MOT operating on the ^{1}S_{0}→^{3}P_{1} 7.5 kHz intercombination transition at 689 nm. About 2,000 atoms are then loaded into a cavityenhanced onedimensional optical lattice at 813.4 nm. The cavity mirrors are placed outside the vacuum chamber and the lattice light, generated with an injectionlocked Ti:Sapphire laser, is stabilized to the cavity using the PoundDreverHall technique, using a doublepassed acoustooptic modulation as a frequency actuator.
Stable laser
The ^{87}Sr sample is probed on the ^{1}S_{0}→^{3}P_{0} 1 mHz clock transition with a 698nm diode laser, which is stabilized to 26 mHz using a 40cm UltralowExpansion glass (ULE) cavity^{14,21}. The cavity enclosure features bipolar temperature control, a passive heat shield, a doublechambered vacuum, active vibration cancellation and acoustic shielding. The stabilized laser passes through an independent acoustooptic modulator (AOM) to steer the frequency of the clock laser light reaching the atoms.
Atomic servo
The offset of the clock laser frequency relative to the clock transition is determined with Rabi spectroscopy. In this work, measurements use Rabi pulse lengths from 160 ms to 4 s. The excited state population fraction after clock spectroscopy is measured by counting the number of ^{1}S_{0} ground state atoms using ^{1}S_{0}→^{1}P_{1} fluorescence, repumping the ^{3}P_{0} excited state population to the ground state and again counting the number of ground state atoms. To lock the clock laser to the atoms, two excited state population measurements are performed on the clock transition (one on each side of the resonance centre). The difference between these measurements is used as an error signal, which is processed by a digital proportionalintegralderivative (PID) controller to steer the laser frequency onto the clock transition resonance.
Lockin measurements with the atomic servo
Many systematic uncertainties are measured using a digital lockin technique. In this scheme, an experimental parameter is set at one value, the clock transition is interrogated and the atomic servo computes a frequency correction^{22}. The same procedure is then performed for a different value of the experimental parameter, using a second, independent atomic servo loop. As the experiment alternates between these two states, data are recorded and time stamped. Demodulation occurs in post processing. In all cases we seek the difference between the resonance centres measured by these control loops.
Density shift
The use of spinpolarized ultracold fermions suppresses swave interactions among our atoms; however, pwave interactions that shift the clock transition can be significant at high precision. This density shift is proportional to the atomic density and insensitive to temperature (due to its pwave nature and the onedimensional lattice^{18}). The density shift is greatly reduced compared with our previous generation Sr clock, due to the use of a cavityenhanced optical lattice^{21}. To measure this shift, we perform a lockin measurement by modulating the atom number and looking for a frequency shift. Extrapolating this result to an operating atom number of 2,000 and trap depth of 71 E_{rec} (where E_{rec} is the lattice photon recoil energy), we reach a density shift of (−3.5±0.4) × 10^{−18} (Fig. 5).
Lattice Stark shift
A lockin measurement is performed for different lattice powers to study the intensity dependence of the lattice Stark shift. We determine this shift as a function of the optical trap depth at the location of the atoms, U_{0}, which is proportional to the lattice intensity. The value of U_{0} is determined from the trap frequency along the lattice axis, which is measured using resolved sideband spectroscopy.
Changing U_{0} also modulates the trap volume, which creates a parasitic density shift that can mimic a lattice light shift. A Gaussian density profile predicts that the density shift scales similar to NU_{0}^{3/2}. In our system, we experimentally verify this relation with negligible uncertainty. To cancel effects of the density shift on this measurement, we modulate the atom number according to the NU_{0}^{3/2} scaling such that there is commonmode density shift cancellation. To further ensure that the density shift is removed, in post processing we remove data with the largest atom number fluctuations until the average differential density shift is well below the final measurement precision.
U_{0} is stabilized with a laser intensity servo by monitoring the cavity lattice transmission. The lattice frequency is locked to a Yb fibre laser opticalfrequency comb referenced to the NIST maser array. Varying the lattice intensity and frequency, we find the magic wavelength where the clock shift is not responsive to changes in U_{0}.
Drifting background magnetic fields can cause the atom’s quantization axis to vary with respect to the clock laser polarization. This creates a drifting ac Stark shift. To solve this problem, we run a background magnetic field servo^{1} during the ac Stark shift measurement.
At some level, terms nonlinear in U_{0} (such as hyperpolarizability and M1E2 shifts) will be required to precisely model the lattice intensity. To measure these small terms, ref. 43 relied on the ability to obtain lattices as deep as 10^{3} E_{rec}, to achieve a large lattice intensity modulation amplitude. However, the measurement could have been susceptible to technical issues such as a noisy tapered amplifier^{43} used to generate lattice light or parasitic density shift effects, which could be significant for such large changes in lattice trap^{25}. To check whether our data supports terms nonlinear in U_{0} to model the lattice light shift, we use an Ftest^{44} yielding F=0.17 for 22 degrees of freedom (corresponding to unbinned data). Therefore, within our measurement precision, our data only supports a linear model (Fig. 6). We note also that all our lattice Stark shift measurements are made near the clock operating condition, with each data point reaching the statistical uncertainty at the 1 × 10^{−17} level. Together, these points determine the Stark shift correction at the 1 × 10^{−18} level for the relevant condition of our clock.
If we were to assume significant hyperpolarizability, we can use our data to infer a hyperpolarizability shift coefficient of (0.3±0.3) μHz E_{rec}^{−2}. This is consistent with the value reported in ref. 43. We could also use the hyperpolarizability coefficient of ref. 43 to correct our data, resulting in a minimal increase in our total uncertainty (from 2.1 × 10^{−18} to 2.4 × 10^{−18}). However, as our statistical tests do not justify hyperpolarizability, only linear behaviour is assumed in our quoted ac Stark shift.
Temperature sensors
The invacuum temperature sensors, Heraeus thinfilm PRTs, are mounted on the end of borosilicate glass tubes sealed to mini vacuum flanges. PRTs are a wellestablished technology for accurate thermometry and are ultrahighvacuum (UHV) compatible. The PRTs are prequalified by cycling their temperatures between an ice melting point (temperature stable to 1 mK) and 200 °C, and then choosing sensors that shifted <1 mK over four cycles. Fourwire phosphorbronze connections to the sensors are soldered to electrical feedthroughs in the flanges. The sensor resistance is measured with a bridge circuit, comparing the PRTs with a 1p.p.m. resistance standard. Resistance measurements are taken with forward and reversed excitation currents for data processing that removes thermocouple effects. Electrical error is quantified in Table 2 of the main text.
The mounting structures were installed in a test chamber and hand carried on a passenger flight to Gaithersburg, Maryland, for calibration at the NIST Sensor Technology Division. At NIST, the sensors were calibrated by comparing them with standard PRTs, traceable to NIST’s ITS90 temperature scale and accurate to 1 mK, using a water comparison bath with 1 mK temperature stability^{45}. The temperature uniformity in the isothermal region of the bath is within 1 mK. As thinfilm PRT calibration shifts are quasirandom, mechanisms that could affect the calibrations would cause the two sensors to disagree. Agreement between the sensors throughout the shipping and installation process strongly suggests that no calibration shifts have occurred. Thinfilm PRTs are generally robust against calibration shifts due to impacts.
We deal with immersion error by a twostage process. First, the test chamber is filled with pure helium and the sensors are calibrated to the standard PRTs. Data are fit to the Callendar van Dusen equation, R_{He}=R_{0}(1+AT+BT^{2}), where R_{0}, A and B are fit parameters. The helium acts as an exchange gas, enabling radial heat exchange along the glass stem and suppressing immersion error. Second, we measure the sensor resistance under vacuum, R_{vacuum}, as a function of T_{flange}–T_{primary}. To quantify immersion error, we fit R_{vacuum}–R_{He}=C(T_{flange}–T_{primary})+Δ, where C and Δ are fit parameters. These two equations are used to obtain T_{primary} as a function of R_{vacuum} and T_{base}. Sensor selfheating is studied by varying the excitation current and extrapolating the results to zero current.
The sensors are installed in the clock chamber using a gas backflow. After installation, sensor baking at 150 °C means that 1.0 mK uncertainty, from thermal cycling, must be added to Table 2. One of the sensors can be translated inside the vacuum chamber with an edgewelded bellows. For clock operation, this sensor is positioned 2.5 cm from the atoms to prevent coating with strontium. The temperature difference between the atom location and 2.5 cm away is (1.45±0.03) mK, which is included in Table 2.
The sensor translation measurements and temperature measurements throughout the inside of the BBR shield confirm that temperature gradients are small, indicating a wellthermalized environment. Compared with previous efforts^{1}, temperature gradients in the clock chamber are now smaller, because greater care was taken to minimize heat sources inside the BBR shield. To quantify the nonthermal heat shift, we model the geometry and emissivities of the vacuum chamber^{1}. We find that our simulation is insensitive to changes in the emissivity values, and that the nonthermal heat correction is bounded below the 1 × 10^{−19} level for our level of temperature uniformity. The nonthermal correction has been included in the ‘Static BBR’ entry of Table 1 rather than listed in Table 2.
Decay measurement
After population is driven to the ^{3}D_{1} state (Fig. 4a), 689 nm fluorescence from the ^{3}D_{1}→^{3}P_{1}→^{1}S_{0} cascade is collected with a photomultiplier tube and then read out and time binned (using a 40ns bin size) with an SR430 event counter. This photon counting setup provides 0.4 ns of timing uncertainty.
Our statistics have confirmed that the noise in this measurement is Poissonian. Simulating the measurement with the appropriate noise process shows that our fits should be given Poisson weighting to correctly obtain the fit uncertainty.
Other simulations show that the fit does not accrue an appreciable bias due to the specific pulse shape when we use pulses shorter than 300 ns or when we remove data when the pulse is on from the fit. To ensure that this fit bias is doubly suppressed, we take both approaches. We take 0.1 ns as a conservative bound on the remaining uncertainty.
We have calculated the correction due to the ^{3}D_{1} hyperfine structure to be at the negligible 0.001% level. Therefore, we choose 0.1 ns as a comfortable upper bound on this effect.
We quantify systematic bias from stray distributedfeedback (DFB) laser light by switching off the AOM used to pulse this laser, while attempting to scan the ^{3}P_{0}→^{3}D_{1} transition. We are able to observe this transition with stray light for exposure times of hundreds of milliseconds. By simulating the results of this scan, we can put a small 0.01 ns upper bound on stray laser light effects. We put the same bound on systematic bias from stray 2.6 μm radiation originating from the ambient heat in our lab.
We study the measured decay rate as a function of atom number to check for density dependence. We confirm that the decay rate is constant in density within our precision using an Ftest, comparing a constant with a model linear in density. With a value of F=0.045 for the statistic (where there are 11 degrees of freedom), this test indicates no density dependence.
Dc Stark shift
A background dc electric field can arise from various sources, such as patch charges^{29} or electronics^{27}. We have only measured a significant background dc Stark shift along one direction. This axis passes through the two largest viewports and the centre of the MOT coils.
To combat possible changes in the dc Stark shift, we actively suppress this shift with electrodes placed on the two large viewports. We measure ν_{+}, the total dc Stark shift with the applied field in one direction, and ν_{}, the shift with the applied field flipped in direction. The background field is proportional to (ν_{+} −ν_{−}), which is processed by a digital Proportional–Integrator servo. The servo applies a voltage to the electrodes to null the background field. The nonlinearity of the shift in electric field means that shift measurements average down rapidly when the background field is well cancelled. We measure a low 10^{−20} level shift with an uncertainty of (−0.1±1.1) × 10^{−19} in 20 min of averaging time.
Probe Stark shift
We perform this measurement by locking two independent atomic servos to 20 and 180 ms πpulses. By keeping the pulse area, which is proportional to the square root of the probe intensity, fixed at a πpulse, we can perform lownoise measurements of the probe Stark shift, which is linear in probe intensity. To resolve the shift well, we perform a large amplitude probe intensity modulation using a motor to move a neutral density filter in and out of the clock laser beam path. Control measurements confirm that this filter does not introduce systematic bias.
To prevent issues with manybody effects that might shift the clock transition frequency as a function of atom number, we study the probe Stark shift with a clock operation atom number of 2,000. Extrapolating this result to an operating clock pulse of 1 s, we observe a probe Stark shift of (−3.2±1.7) × 10^{−20}.
Firstorder Zeeman shift
The firstorder Zeeman shift is greatly suppressed by averaging locks to the two m_{F}=±9/2 stretched states^{26}. A residual firstorder Zeeman shift could occur if there is appreciable magnetic field drift in between clock interrogations. We combat this by employing active background magnetic field cancellation^{1}.
The difference between the m_{F}=±9/2 stretched state frequency measurements is proportional to the background magnetic field. Drifts in this difference indicate a residual firstorder Zeeman shift. Averaging down this difference, we measure a firstorder Zeeman shift of (−1.6±2.0) × 10^{−19}.
Secondorder Zeeman shift
We measure the secondorder Zeeman shift by monitoring the atomic frequency shift while modulating between high and lowbias magnetic field values. We then extrapolate the observed frequency shift to operating conditions, using the fact that the shift is proportional to the bias field squared. The secondorder Zeeman shift is measured as a function of the frequency difference between the m_{F}=±9/2 stretched states, Δν_{stretch}, which is proportional to the bias field magnitude. For clock operation, Δν_{stretch}=300 Hz.
Background field drift can change the direction of the bias field, creating a timevarying lattice tensor ac Stark shift that would affect the measurement. To prevent this, we operate a background field cancellation servo. In addition, we reduce the sensitivity to drifts by aligning the field and the clock laser polarization. This is done by minimizing the amplitude of m_{F} changing σ transitions. With this setup, we put a 10^{−20} level upper bound on systematic bias from field drift.
We measure the secondorder Zeeman shift coefficient, the shift normalized by , to be (−5.82±0.07) × 10^{−16} kHz^{−2}. This number is an atomic property and is independent of a particular measurement; thus, we average this result with four other determinations of this coefficient^{1,25,46,47}. The final value for the shift at Δν_{stretch}=300 Hz is (−51.7±0.3) × 10^{−18}. We use a reduced inflated uncertainty to account for nonstatistical variations between these data points.
Other shifts
Line pulling occurs when offresonant spectroscopic features can slightly shift the clock transition frequency. This can be caused by imperfect spin polarization leaving population in m_{F} states aside from ±9/2, clock laser ellipticity causing us to drive σ transitions, or clock transition sidebands that result from tunnelling between lattice sites. Calculations and data allow us to put a conservative upper bound on this effect at 1 × 10^{−19}.
The firstorder Doppler effect is not present in an optical lattice probed along the lattice axis, where the optical phase of the lattice and that of the clock probe lasers are referenced to a common mirror. A secondorder Doppler shift is, in principle, present, but it is estimated to be at the 10^{−21} level. We put a comfortable 1 × 10^{−19} bound on this effect.
Collisions with the background gases in our UHV chamber can shift the clock transition frequency. At normal operating vacuum pressure, the background gas is largely hydrogen. We use the model of ref. 48 to put an upper bound on this effect of 6 × 10^{−19}.
Steadystate error in the atomic servo could shift the measured clock transition frequency. We average lock data and find a servo offset of (−5±4) × 10^{−19}.
Clock operation uses an AOM to scan the frequency and pulse the intensity of the clock laser. Phase transients occurring when this AOM pulses would appear as frequency shifts in clock measurements. We study the AOM phase transients by looking at the beat of the first AOM order with the 0th order on a digital phase detector. We also calibrated the phase transients of the detector itself. Drawing on the analysis of ref. 49, we infer an AOM phase chirp shift of (6±4) × 10^{−19}.
Statistical methods
To calculate the shift of a given record, we perform a post processing demodulation of the data to extract a signal. The shift represents the mean of this signal. The statistical uncertainty is calculated from the s.e.m. If the reduced , the statistical uncertainty is inflated by . To remove the effects of residual laser drift, which is highly linear, from lockin measurements, we use ‘threepoint strings’. This analysis involves processing successive triplets of frequency measurements in linear combinations meant to cancel linear drift^{50}.
Additional information
How to cite this article: Nicholson, T. L. et al. Systematic evaluation of an atomic clock at 2 × 10^{−18} total uncertainty. Nat. Commun. 6:6896 doi: 10.1038/ncomms7896 (2015).
References
 1.
Bloom, B. J. et al. An optical lattice clock with accuracy and stability at the 10^{−18} level. Nature 506, 71–75 (2014).
 2.
Chou, C. W., Hume, D. B., Koelemeij, J. C. J., Wineland, D. J. & Rosenband, T. Frequency comparison of two highaccuracy Al^{+} optical clocks. Phys. Rev. Lett. 104, 070802 (2010).
 3.
Hinkley, N. et al. An atomic clock with 10^{−18} instability. Science 341, 1215–1218 (2013).
 4.
Madej, A. A., Dubé, P., Zhou, Z., Bernard, J. E. & Gertsvolf, M. ^{88}Sr^{+} 445THz Singleion reference at the 10^{−17} level via control and cancellation of systematic uncertainties and its measurement against the SI second. Phys. Rev. Lett. 109, 203002 (2012).
 5.
Ushijima, I., Takamoto, M., Das, M., Ohkubo, T. & Katori, H. Cryogenic optical lattice clocks. Nat. Photonics 9, 185–189 (2015).
 6.
Wineland, D. J. Nobel Lecture: superposition, entanglement, and raising Schrödinger’s cat. Rev. Mod. Phys. 85, 1103–1114 (2013).
 7.
Haroche, S. Nobel Lecture: controlling photons in a box and exploring the quantum to classical boundary. Rev. Mod. Phys. 85, 1083–1102 (2013).
 8.
Zhang, X. et al. Spectroscopic observation of SU(N)symmetric interactions in Sr orbital magnetism. Science 345, 1467–1473 (2014).
 9.
Scazza, F. et al. Observation of twoorbital spinexchange interactions with ultracold SU(N)symmetric fermions. Nat. Phys. 10, 779–784 (2014).
 10.
Godun, R. M. et al. Frequency ratio of two optical clock transitions in Yb^{+} and constraints on the time variation of fundamental constants. Phys. Rev. Lett. 113, 210801 (2014).
 11.
Huntemann, N. et al. Improved limit on a temporal variation of m_{p}/m_{e} from comparisons of Yb^{+} and Cs atomic clocks. Phys. Rev. Lett. 113, 210802 (2014).
 12.
Cacciapuoti, L. & Salomon, C. Space clocks and fundamental tests: The ACES experiment. Eur. Phys. J. Spec. Top. 172, 57–68 (2009).
 13.
Kessler, T. et al. A sub40mHzlinewidth laser based on a silicon singlecrystal optical cavity. Nat. Photonics 6, 687–692 (2012).
 14.
Bishof, M., Zhang, X., Martin, M. J. & Ye, J. Optical spectrum analyzer with quantumlimited noise floor. Phys. Rev. Lett. 111, 093604 (2013).
 15.
Schmidt, P. et al. Spectroscopy using quantum logic. Science 85, 749–752 (2005).
 16.
Ye, J., Kimble, H. J. & Katori, H. Quantum state engineering and precision metrology using stateinsensitive light traps. Science 320, 1734–1738 (2008).
 17.
Boyd, M. M. et al. Optical atomic coherence at the 1second time scale. Science 314, 1430–1433 (2006).
 18.
Martin, M. et al. A quantum manybody spin system in an optical lattice clock. Science 341, 632–637 (2013).
 19.
Dick, J. G. In Proc 19th Precise Time Time Interval Meet. 133–147 (1987).
 20.
Itano, W. et al. Quantum projection noise: Population fluctuations in twolevel systems. Phys. Rev. A 47, 3554 (1993).
 21.
Nicholson, T. L. et al. Comparison of two independent Sr optical clocks with 1 × 10^{−17} stability at 10^{3} s. Phys. Rev. Lett. 109, 230801 (2012).
 22.
Boyd, M. et al. ^{87}Sr lattice clock with inaccuracy below 10^{−15}. Phys. Rev. Lett. 98, 083002 (2007).
 23.
Katori, H. In Proc. 6th Symp. Freq. Stand. Metrol. Univ. St. Andrews, Fife, Scotl 323–330 (2002).
 24.
Kimble, H. J. In Proc. XIV Int. Conf. Laser Spectrosc. 80–89 (1999).
 25.
Westergaard, P. et al. Latticeinduced frequency shifts in Sr optical lattice clocks at the 10^{−17} level. Phys. Rev. Lett. 106, 210801 (2011).
 26.
Takamoto, M. et al. Improved frequency measurement of a onedimensional optical lattice clock with a spinpolarized fermionic ^{87}Sr isotope. J. Phys. Soc. Jpn 75, 104302 (2006).
 27.
Falke, S. et al. A strontium lattice clock with 3 × 10^{−17} inaccuracy and its frequency. New J. Phys. 16, 073023 (2014).
 28.
Mcdonald, M., Mcguyer, B. H., Iwata, G. Z. & Zelevinsky, T. Thermometry via light shifts in optical lattices. Phys. Rev. Lett. 114, 023001 (2015).
 29.
Lodewyck, J., Zawada, M., Lorini, L., Gurov, M. & Lemonde, P. Observation and cancellation of a perturbing dc Stark shift in strontium optical lattice clocks. IEEE Trans. Ultrason. Ferroelectr. Freq. Control 59, 411–415 (2012).
 30.
Safronova, M. S., Porsev, S. G., Safronova, U. I., Kozlov, M. G. & Clark, C. W. Blackbodyradiation shift in the Sr optical atomic clock. Phys. Rev. A 87, 012509 (2013).
 31.
Porsev, S. & Derevianko, A. Multipolar theory of blackbody radiation shift of atomic energy levels and its implications for optical lattice clocks. Phys. Rev. A 74, 020502 (2006).
 32.
Middelmann, T., Falke, S., Lisdat, C. & Sterr, U. High accuracy correction of blackbody radiation shift in an optical lattice clock. Phys. Rev. Lett. 109, 263004 (2012).
 33.
Boguhn, D. & Koepke, M. Typical R(T_{90}) characteristics of platinum thinfilm resistance thermometers in the temperature range from −50 °C to +660 °C. Int. J. Thermophys. 32, 2379–2387 (2011).
 34.
Beloy, K. et al. Atomic clock with 1 × 10^{−18} roomtemperature blackbody Stark uncertainty. Phys. Rev. Lett. 113, 260801 (2014).
 35.
Beloy, K. et al. Determination of the 5d6s^{3}D_{1} state lifetime and blackbodyradiation clock shift in Yb. Phys. Rev. A 86, 051404(R) (2012).
 36.
Dick, G., Prestage, J., Greenhall, C. & Maleki, L. In Proc. 22nd Precise Time Time Interval Meet. 487–508 (1990).
 37.
Biedermann, G. W. et al. Zerodeadtime operation of interleaved atomic clocks. Phys. Rev. Lett. 111, 170802 (2013).
 38.
Cole, G. D., Zhang, W., Martin, M. J., Ye, J. & Aspelmeyer, M. Tenfold reduction of Brownian noise in highreflectivity optical coatings. Nat. Photonics 7, 644–650 (2013).
 39.
Kómár, P. et al. A quantum network of clocks. Nat. Phys. 10, 582–587 (2014).
 40.
Bohnet, J. G. et al. Reduced spin measurement backaction for a phase sensitivity ten times beyond the standard quantum limit. Nat. Photonics 8, 731–736 (2014).
 41.
Leroux, I. D., SchleierSmith, M. H. & Vuletić, V. Implementation of cavity squeezing of a collective atomic spin. Phys. Rev. Lett. 104, 073602 (2010).
 42.
Appel, J. et al. Mesoscopic atomic entanglement for precision measurements beyond the standard quantum limit. Proc. Natl Acad. Sci. USA 106, 10960–10965 (2009).
 43.
Le Targat, R. et al. Experimental realization of an optical second with strontium lattice clocks. Nat. Commun. 4, 2109 (2013).
 44.
Bevington, P. R. & Robinson, D. K. Data Reduction and Error Analysis for the Physical Sciences McGraw Hill (2002).
 45.
Tew, W. L. et al. Calibration of thinfilm platinum sensors for use in the JILA Sr II Clock. Natl Inst. Stand. Technol. Intern. Rep. http://dx.doi.org/10.6028/NIST.IR.8046 (2015).
 46.
Ludlow, A. D. et al. Sr lattice clock at 1 × 10^{−16} fractional uncertainty by remote optical evaluation with a Ca clock. Science 319, 1805–1808 (2008).
 47.
Falke, S. et al. The ^{87}Sr optical frequency standard at PTB. Metrologia 48, 399–407 (2011).
 48.
Gibble, K. Scattering of coldatom coherences by hot atoms: frequency shifts from backgroundgas collisions. Phys. Rev. Lett. 110, 180802 (2013).
 49.
Falke, S., Misera, M., Sterr, U. & Lisdat, C. Delivering pulsed and phase stable light to atoms of an optical clock. Appl. Phys. B 107, 301–311 (2012).
 50.
Swallows, M. D. et al. Suppression of collisional shifts in a strongly interacting lattice clock. Science 331, 1043–1046 (2011).
Acknowledgements
We thank X. Zhang and M. Bishof for useful discussions, and B. Bjork, L. Sonderhouse and H. Green for technical assistance. This research is supported by the National Institute of Standards and Technology, Defense Advanced Research Projects Agency QuASAR Program and NSF Physics Frontier Center at JILA. M.D.B. acknowledges support from the JILA Visiting Fellows programme. G.E.M. acknowledges support from the NIST Director’s Office Fellowship. Any mention of commercial products does not constitute an endorsement by NIST.
Author information
Author notes
 B.J. Bloom
Present address: Intel, Hillsboro, OR, USA
Affiliations
JILA, National Institute of Standards and Technology and University of Colorado, Boulder, Colorado 803090440, USA
 T.L. Nicholson
 , S.L. Campbell
 , R.B. Hutson
 , G.E. Marti
 , B.J. Bloom
 , R.L. McNally
 , W. Zhang
 , M.D. Barrett
 & J. Ye
Department of Physics, University of Colorado, Boulder, Colorado 803090390, USA
 T.L. Nicholson
 , S.L. Campbell
 , R.B. Hutson
 , G.E. Marti
 , B.J. Bloom
 , R.L. McNally
 , W. Zhang
 & J. Ye
Centre for Quantum Technologies, 3 Science Drive 2, Singapore 117543, Singapore
 M.D. Barrett
University of Delaware, Newark, Delaware 19716, USA
 M.S. Safronova
Joint Quantum Institute, NIST and the University of Maryland, College Park, Maryland 20899, USA
 M.S. Safronova
National Institute of Standards and Technology, Gaithersburg, Maryland 20899, USA
 G.F. Strouse
 & W.L. Tew
Authors
Search for T.L. Nicholson in:
Search for S.L. Campbell in:
Search for R.B. Hutson in:
Search for G.E. Marti in:
Search for B.J. Bloom in:
Search for R.L. McNally in:
Search for W. Zhang in:
Search for M.D. Barrett in:
Search for M.S. Safronova in:
Search for G.F. Strouse in:
Search for W.L. Tew in:
Search for J. Ye in:
Contributions
T.L.N., S.L.C., R.B.H., G.E.M., B.J.B., R.L.M., W.Z., M.D.B. and J.Y. contributed to the overall operations of the experiments. M.S.S. carried out theory calculations of the atomic structure responsible for the dynamic BBR frequency shift. G.F.S. and W.L.T. calibrated the platinum sensors and established a rigorous thermometry procedure. All authors discussed the results, contributed to the data analysis and worked together on the manuscript.
Competing interests
The authors declare no competing financial interests.
Corresponding author
Correspondence to J. Ye.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Further reading

Innershell clock transition in atomic thulium with a small blackbody radiation shift
Nature Communications (2019)

Optical clock comparison for Lorentz symmetry testing
Nature (2019)

The concept of laserbased conversion electron Mössbauer spectroscopy for a precise energy determination of 229mTh
Hyperfine Interactions (2019)

An optical clock to go
Nature Physics (2018)

Carrier thermometry of cold ytterbium atoms in an optical lattice clock
Scientific Reports (2018)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.