The ability to control dynamics of quantum states by optical interference, and subsequent electrical read-out, is crucial for solid state quantum technologies. Ramsey interference has been successfully observed for spins in silicon and nitrogen vacancy centres in diamond, and for orbital motion in InAs quantum dots. Here we demonstrate terahertz optical excitation, manipulation and destruction via Ramsey interference of orbital wavepackets in Si:P with electrical read-out. We show milliradian control over the wavefunction phase for the two-level system formed by the 1s and 2p states. The results have been verified by all-optical echo detection methods, sensitive only to coherent excitations in the sample. The experiments open a route to exploitation of donors in silicon for atom trap physics, with concomitant potential for quantum computing schemes, which rely on orbital superpositions to, for example, gate the magnetic exchange interactions between impurities.
Control of quantum states has already led to many important technologies from pulsed nuclear magnetic resonance to optical lasers. While the early experiments by Rabi et al. have remained influential in atomic physics for the entire period since they were originally performed, their significance has become much greater to engineering physics over the last two decades in the context of the development of quantum information technology. One of the key experiments was that of Ramsey that showed how to use pulsed radiation to measure atomic excitation energies with high resolution1, and at the same time also demonstrated control over the wavefunction of the same two-level atomic systems, in the form of the much-celebrated ‘Ramsey fringes’. A second development has been the electrical read-out of atomic states in semiconductors2,3, recently focusing especially on quantum-controlled spins and charges in silicon and GaAs4,5,6,7,8,9,10,11,12. Here, we take advantage of coherent, tuneable pulsed THz radiation from a free-electron laser (FEL)12,13,14,15,16,17 to demonstrate electrical read-out of coherent orbital excitations for the phosphorous donor in silicon.
Beyond underpinning contemporary information technology, silicon is an excellent substrate for quantum information science9,10,11 partly because of the enormous potential advantage that a large number of atoms can be lithographically deposited with atomic resolution18,19. Most of the attention has been focussed on impurity spins, for which microwave control and electrical read-out have been demonstrated6,7, with the longest decoherence times for any solid-state system8. There has been much less exploration of the orbital degree of freedom because, given the low Rydberg energy in the heavily screened silicon ‘vacuum’2,20, terahertz (THz) technology is a prerequisite. The availability of free-electron lasers has opened this topic, allowing demonstration of incoherent relaxation13,14,17 and photon echoes15, corresponding to T1 and T2 processes for orbital transitions of impurities in silicon. Solid-state THz sources have also been used for field ionization studies22.
In this work, we advance silicon orbitronics by demonstrating electrical detection of Ramsey fringes for the 1s→2p transition of Si:P ensembles containing as few as 105 donors. The fringes, manifestations of the desired wavepacket creation and destruction, are easy to establish in the THz regime—especially compared with the visible21, because in the THz domain free space optics and ordinary mechanical delay stages readily provide sub-wavelength resolution. From the decay of the fringes, we obtain T2*, the inhomogeneous decoherence time, and we show that the electrically detected result is consistent with the T2* obtained via all-optical echo detection after two Ramsey pulses. Apart from showing that a simple silicon wafer with some electrical contacts is sufficient to perform one of the classic experiments of atomic physics, our measurements should lead to future implementations of quantum gates.
Electrically detected Ramsey fringes
Figure 1a shows a schematic of the potential for a phosphorous impurity in silicon (Si:P) under applied bias, along with the 1s and 2p wavefunctions, and the bound Rydberg state energies below the ionization threshold. The electrical detection mechanism2,3, termed photothermal ionization spectroscopy (PTIS), is based on the much higher thermal ionization probability for an excited 2p state than the ground 1s state (see again Fig. 1a), implying that the sample conductivity will be enhanced even after non-ionizing photoexcitation from the 1s to 2p states. The main part of Fig. 1a is the resulting photoconductivity spectrum under small-signal illumination, showing resonances corresponding to transitions between the bound states. Previous workers have taken advantage of PTIS for continuous wave spectroscopy in the small-signal, linear regime2, or even incoherent pulsed dynamics3, but here we exploit it for coherent, time domain experiments.
The free-electron laser ‘FELIX’ is ideally suited as a pump for coherent manipulation of the donor orbitals in silicon because it is tuneable over the required THz (far infrared) range. Ti:sapphire-based THz transient systems are also useful for dynamics22, but have very wide bandwidth and are not appropriate for resonance experiments such as these. FELIX provides transform-limited pulses with controllable duration16, high peak pulse energy and high polarization purity, for use in pulsed experiments.
To visualize the coherent, pulsed excitation of a two-level quantum oscillator such as that defined by the 1s and 2p levels of a hydrogenic atom, one often makes use of the Bloch sphere (Fig. 1b–d), which represents the amplitude and relative phase of the coefficients in the superposition. In this picture, a vector pointing towards either of the poles represents the system in one of the eigenstates (we shall use the south pole to be the ground state, and the north pole to be the excited state), while a 50:50 superposition is represented by an equatorial vector and the phase is given by the azimuthal angle. After coherent, resonant excitation by a laser pulse, the Bloch vector is left with a rotation about the x axis by an angle, θ, proportional to the pulse area (the product of the pulse electric field amplitude and its duration), and in the dark the vector rotates about the z axis with the natural frequency (NB: in this picture we do not use a co-rotating reference frame). The Ramsey sequence (Fig. 1b) consists of a pair of equal pulses. The first Ramsey pulse leaves the Bloch vector rotated by θ and the effect of the second pulse depends on its precise arrival time. If it arrives after a whole number of periods of the natural oscillation, the light constructively interferes with the electronic state producing a final elevation of 2θ. If a half-integer number of periods has elapsed, the light–matter interference is destructive and the final elevation is zero. Inhomogeneous broadening is produced by the random arrangement of the different isotopes of silicon around each phosphorus impurity, which means that the oscillators all have slightly different natural frequencies. The primary effect of this broadening is that Bloch vectors precess at different rates, which means that there is a spread of phases when the second Ramsey pulse arrives and the interference contrast decays. Conventionally, π/2 pulses are used for Ramsey spectroscopy, but any equal area pulses produce the same fringes and π/4 pulses are convenient for echo detection experiments described later.
Mixtures of 1s and 2p states produced by coherent THz pulse sequences, such as Ramsey pairs illustrated in Fig. 1b,c, can be detected in the electrical conductivity, which is sensitive primarily to the 2p occupancy via the subsequent, much-longer lived, ionization. Our method allows us to deduce coherent control of the two-level system because the rectifying nature of electrical detection implies that for given coherent oscillations in the hydrogen-like states of the silicon impurities at given pulse delays, the photocurrent signal allows for read-out of their net amplitude. Said another way, the amplitude of the coherent wave superposition will affect the probability of thermally assisted photoionization.
In our experiments, the FELIX laser was tuned to the frequency of the 1s–2p± transition (see Methods). The beam was separated with a beam splitter into two equal, collinear pump beams (that is, the pulses were split into two, denoted as pulse 1 and pulse 2), each with an independent intensity controller and delay stage (we denote the separation in arrival times as τ12). The beam was then focused onto the sample, which was liquid at helium temperature. The intensities were adjusted so that both beams 1 and 2 were π/4 pulses (corresponding to the 0.15μJ cm−2 peak, in a beam of radius 1 mm and pulse duration 5.7 ps). The photoconductivity signal was measured as a function of τ12 to give the Ramsey fringes (Figs 1b,c and 2).
Figure 2b shows the electrically detected Ramsey fringes in Si:P (see Methods for a description of the laser, optical apparatus and sample). Short expanded sections contain clear interference fringes in the time domain, but they are much more obvious in the frequency domain as shown by the Fourier transform (FT) computed over each section. The peak at the transition frequency is clearly visible and can still be seen even at 60 ps. Figure 2c shows the amplitude of the fringe envelope as a function of time delay produced with a FT filter (see Methods), along with the noise level, and the equivalent analysis for an autocorrelation of the incident FEL beam taken with a reference detector. The Ramsey interference lasts much longer than the autocorrelation reference. The measured laser spectral width was ΔfL=0.066±0.001 THz and the autocorrelation fringe duration (blue line from Fig. 2c) is ΔτL=17.4±1 ps. The Ramsey fringe duration is ΔτR=59±10 ps, (red line in Fig. 2c). In the small-signal PTIS (Fig. 1a) the 1s(A1)–2p± line is approximately Gaussian, as expected for an inhomogeneous line, with width ΔfA=0.028 THz (the spectrum was taken with 0.006 THz resolution).
Optically detected Ramsey fringes
The Ramsey fringes described so far utilize the simplest possible pulse sequence and demonstrate the electrical detection of quantum superpositions of impurity orbitals in silicon. Although the analysis is straightforward and yields an inhomogeneous dephasing time in good agreement with expectations, it relies on taking account of an inelastic scattering process as well as the Ramsey fringes. It is therefore useful to obtain an independent check of the analysis, and more importantly, to verify that electrical detection in this time-resolved experiment is as straightforward as we posit above. To this end, we devised an all-optical echo detection scheme15 that is sensitive only to the coherences produced by the Ramsey fringes and completely eliminates any possible effect of the inelastic scattering component. In this experiment, an initial pump pulse pair (pulses 1 and 2 shown in Fig. 1d for the case that they are π/4 pulses, in phase) forms a coherent superposition of states represented by a rotation of π/2 about the x axis, onto the equator of the Bloch sphere. The superposition rotates around the z axis at the natural frequency and is allowed to dephase until a third rephasing pulse (pulse 3) gives a rotation about x again, this time by π, so that the phase lead/lag is reversed. The superpositions continue to evolve, allowing coherent emission to build up after waiting for a further time τ23. The echo intensity as a function of τ23 gives directly the inverse homogeneous phase decoherence rate, T2−1. Inhomogeneous broadening, due to static random fields, is eliminated in the photon echo experiment because the dephasing for which they are responsible is precisely the same before the π pulse and afterwards. In our echo detection of Ramsey fringes, the echo strength is used as a measure of the strength of the coherent superposition produced by the Ramsey pair. The echo exhibits interference fringes with a contrast that reduces as the delay τ12 approaches the inhomogeneous dephasing time T2*.
In the optical experiment, the collinear pump beams 1 and 2 produce π/4 pulses as in the previous electrical experiment, but now a rephasing beam (producing a π pulse, beam 3) was also incident on the sample at an angle of about 10° to the pump pulses. The emitted photon echo pulse was then detected at the appropriate angle determined by phase matching by focussing it onto a Ge:Ga cooled detector (see Methods).
The results (Fig. 3b, black data) for the photon echo signal as a function of τ12 contain a single-sided exponential, a constant background and large amplitude interference fringes superposed on these features. In the general case of a three-beam experiment, six different echo signals are radiated at different times and directions23 because each combination of laser pulses coherently interacts with the wave-like excitations produced by the previous ones. Here, by using collinear pump beams with a rephasing beam at an angle of 10°, and choosing a specific detection direction, we investigate the interaction of only two echo components—one for each of the pumps—that are emitted as a coherent sum. We turn first to the component that produces the fixed background in the signal of Fig. 3b. This is the echo produced by the rephasing pulse with the pump that arrives τ23 earlier. As τ23 is fixed, the echo is constant.
The second echo component is due to the rephasing pulse with the other pump, which arrives τ12+τ23 earlier. The amplitude is τ12-dependent due to homogeneous dephasing of the polarization and disappears from view when τ12+τ23≤0. It therefore produces the single-sided exponential component rising at τ12=−τ23=−50 ps in the signal of Fig. 3b. We recorded this delay-dependent component of the echo signal separately by blocking the other pump (see the orange data in Fig. 3b), and the time constant is 40 ps corresponding to T2=160 ps (in agreement with ref. 15) where the factor of 4 occurs because the echo intensity is proportional to the square of the amplitude and the time of the echo emission is twice the delay between the pump and rephasing pulses.
The observed Ramsey fringes are produced by interference between the echoes associated with the two pump pulses. Correspondingly, the Ramsey interference signal peaks when the pumps are precisely coincident, that is, for τ12=0. As well as direct interference between the echoes, there is also interference between scattered light from pulses 1 and 3 (due to slight sample and mirror surface roughness), resulting in interference fringes for photons visible to the detector in the echo direction. This interference peaks when τ12 is near −50 ps. Because the laser produces FT-limited pulses, the fringe envelope will be the pulse length, while the fringe period will be the inverse laser frequency.
For quantitative analysis, we have extracted the envelope function for the fringes as described in the Methods section below. Figure 3d shows the outcome, which clearly demonstrates separate peaks due to scatter and to Ramsey fringes, centred at τ12=−50 and 0 ps, respectively. As expected, the former (Fig. 3d, blue line) is almost identical in width to the autocorrelation (Fig. 3e, red line) whose measured full-width at half-maximum (FWHM) is ΔτL=15.7±1.3 ps and corresponds to the measured laser spectral width ΔfL=0.064±0.001 THz (Fig. 4, orange points). The Ramsey fringes are clearly much broader than the autocorrelation, with measured FWHM ΔτR=32.0±1.6 ps (Fig. 3d, green line). The small-signal absorption line (measured by FT infrared spectroscopy with resolution 0.006 THz) had a FWHM ΔfA=0.046 THz.
In the case of a coherent pulse with a Gaussian envelope, the time–bandwidth product for the linear autocorrelation fringe duration (the FWHM of the envelope amplitude) and the FWHM of the intensity spectrum is ΔτL ΔfL=4ln2/π=0.88 (independent of any chirp in the pulses). In the electrical and optical experiments ΔτL ΔfL=1.11±0.07 and 1.00±0.08, respectively, consistent with the fact that pulses show slight departures from Gaussian. When measuring Ramsey interference as a function of the time delay between the pump pulses, the FWHM duration of the fringe amplitude, ΔτR, is inversely proportional to the FWHM spectral absorption line width ΔfA, so it is easy to compare the result with expectation from the frequency domain. Note that one can define a phase coherence time T* or T2* that is simply proportional to ΔτR, but since there are different conventions (for factors of 2 and π) in different research communities, we try to avoid this nomenclature and refer only to the inhomogeneous line width. For a Gaussian inhomogeneous line, the Ramsey fringes follow ΔτR ΔfA=4ln2/π=0.88 (which is coincidentally the same product as for the autocorrelation fringes). The electrical and optical Ramsey fringe products are ΔτR ΔfA=1.6±0.4 and 1.5±0.2, respectively, which is partly due to the fact that the fringes are convolved with a laser pulse of finite width, and is also an indication that the absorption line is not a pure Gaussian.
It is useful also to display the results in the frequency rather than the time domain. Figure 4 shows that the elastic-scattering interference peak for τ12~−50 ps has a width, corresponding to the laser bandwidth, that is substantially larger than the width of the Ramsey interference, corresponding to the narrower width of the 1s→2p absorption.
Figure 4 shows the FT of the autocorrelation fringes (red) and the comparison with the laser spectrum (orange) off-resonance. All of these measures of the pulse bandwidth, including two time domains (unblocked rephasing pulse for τ12 near 0 and blocked rephasing pulse for τ12 near −50 ps) and one frequency domain (measured simultaneously with a grating monochromator) are consistent. We repeated the experiment of Fig. 3 with various pulse durations down to 5.7 ps (corresponding to ~50 cycles at the frequency used here), and while the Ramsey interference is unaffected by the laser pulse duration, the autocorrelation follows the expected time–bandwidth product.
Figure 4 shows that Ramsey spectroscopy is robust and unaffected by the fact that we are pumping slightly off-resonance. It also touches the original intent of Ramsey to see sharp spectral lines in the presence of a broadband source. There are several applications of our results. The first is simply for calibration of pulses to move Bloch vectors to particular locations on the Bloch sphere, useful both for qubits themselves as well as control bits in various quantum computing schemes. The observation of the echo-detected Ramsey fringes themselves entails such control, and the inset of Fig. 3c shows that we are able to achieve mrad settings on the Bloch sphere at 10 THz. Because a phase delay of 2π corresponds to the 36 μm wavelength employed, improvements to our instrument and especially the ability eventually to regulate its settings using piezoelectric transducers with <10 nm resolution should easily allow us to go below a few mrad.
Photon echo detection method to determine T1
There are other applications of our three-beam experiments. For example, we can follow the practice of spin resonance spectroscopy and use echo detection to measure spin–lattice relaxation times T1. This has significant advantages over the more usual pump–probe experiment13, namely that there is no possibility of artefacts from induced absorption changes due to any excitations other than the intended two-level atom. Examples of such artefacts include the induced absorption by photoionized electrons (which could remain free or fall into unrelated traps) and the coherent artefact caused by four-wave mixing when the pump and probe beams overlap in time24. In this case we use the sequence π-τ12-π/2-τ23-π-echo. The first π-pulse is the preparation pulse and the remainder of the sequence produces the read-out echo. If the time delay between the preparation pulse and the echo sequence is very small or very large the polarization is 100% and a full echo is produced in both cases. There is an intermediate delay time for which the populations are equalized, and thus the subsequent pulses produce no echo. For a sequence with general areas and arrival times A1-τ12-A2-τ23-A3-echo, the area of the echo in the direction 2k3–k2 for short pulses, τ12,23≥0, and k1≠k2≠k3 may be shown to be
The first parenthesis is the incoherent population upon arrival of pulse 2, and the remainder is the echo read-out. For experiments on large ensembles such as this one, A1 is a function of position within the beam spot, and Ae must be averaged over the beam cross-section. The measured echo intensity is proportional to Ae2, and the ordinate of Fig. 5 shows Ae2(A1)/Ae2(0), that is, the signal normalized to its value when the preparation beam was blocked. The time constant for the recovery of the echo at large values of τ12 is just T1. The lines on Fig. 5 contain no fitting parameters other than T1, whose value was 180 ps in agreement with previous work13.
Using both electrical and optical read-out we have demonstrated the creation and destruction of wavepackets with the Ramsey pulse sequence. The electrical detection of orbital quantum oscillations in silicon is an essential stepping stone for carrying out quantum information experiments in silicon. Ultimately, the role of thermal ionization in the detection may be replaced by tunnelling through the barrier of a single electron transistor, as used for spins. We have shown both electrically and optically that Ramsey spectroscopy is robust and unaffected by the fact that we are pumping slightly off-resonance. We have also developed photon echo spectroscopy techniques not only to observe Ramsey fringes, but also to obtain a more reliable value for T1 than given by conventional pump–probe spectroscopy. Beyond the obvious applications to basic physics, control and read-out of Rydberg states for the most common impurity in the most common semiconductor will help to implement certain quantum gate architectures for doped silicon10.
Time structure of FELIX output
The free-electron laser, FELIX, provides pulses separated by 40 ns, and in bursts of duration 4 μs and repetition frequency 5 Hz. The pulse duration/spectral width control was obtained by detuning of the laser cavity length. This alters the synchronism between the inverse round-trip time of the light pulses in the cavity and the injection frequency of the electron pulses, so that the light pulse duration may be increased without affecting the time–bandwidth product, which is near unity16. The pulse energy was controllable up to 10 μJ. A grating spectrometer with a pyroelectric detector array collects a small fraction of the laser light from a hole in one upstream mirror to provide a continually updated spectrum.
Electrical read-out experiment
The sample used for electrical read-out was a commercial float zone <110> silicon wafer of 800 μm thickness with a 2 × 1014 cm−3 phosphorus concentration, with four aluminium contacts in a linear arrangement for four-terminal characterization (Fig. 6). For the photoresponse measurements, a voltage of 12 V was applied across the inner two contacts, which produced a current of 135 μA. PTIS requires slightly elevated temperature to provide sufficient phonons at the excited state ionization energy, but not so much that the ground states start to ionize—the sample was mounted in a continuous flow cryostat with polypropylene windows, in vacuum on the cold finger at 10 K. For small-signal spectroscopy (Fig. 1a), the sample was illuminated with the output of a FTIR interferometer. For Ramsey experiments (Fig. 2), radiation from FELIX was used to illuminate the silicon between the inner contacts. With a beam sizes of ~0.5 mm, around 1.25 × 1011 donors were illuminated. The optical arrangement of Fig. 6 was used, but with the detector removed and the rephasing beam blocked.
Photon echo detection
The sample used for the photon echo detection experiment was a commercially produced float zone <111> silicon wafer of 300 μm thickness with a phosphorus concentration of 6 × 1014 cm−3. The arrangement of beams is shown in Fig. 6. Calibrated wire mesh attenuators and/or polarizer/analyzer pairs were used to control the intensities. Upon incidence the polarization of the light was always perpendicular to the plane of the bench (S-polarization). The relative arrival times between the pulses were controlled by a simple stepper motor-driven delay stage with a practical resolution of 0.5 μm, easily allowing sub-wavelength phase control. The rephasing pulse had an incidence angle of about 10° to the Ramsey pulse pair, which were co-linear (that is, k1=k2). When the rephasing process is complete, the system again exhibits a macroscopic electric dipole moment resulting in a burst of coherent radiation. This photon echo signal is subject to phase-matching conditions, and the echo emission signal was detected in the phase matching ke=2k3–k1 direction. After the sample, the beams were collimated, blocked as required and refocused with off-axis parabolic mirrors onto a helium-cooled Ge:Ga detector. A helium-cooled Ge:Ga photoconductor was also used simultaneously to monitor the autocorrelation signal. In the electrical detection experiment the same arrangement of pumps and reference detector was used (and the rephasing beam was blocked).
For the linear autocorrelation in Fig. 3c, we simply blocked the rephasing beam and detuned the laser away from resonance without altering any alignment, that is, the detector measures scattered light from the pumps (for the inset of Fig. 3c only, to allow accurate estimation of the fringe contrast, we eliminated scatter by removing the sample).
For the experimental fringe envelopes (Figs 2c,d and 3d,e), the raw fringe data (Figs 2b and 3b,c) were downconverted to d.c. by multiplying the data by exp(i2πfLτ12), smoothing and then taking the absolute magnitude. This process turns Gaussian noise into low-frequency Ricean noise, which is the reason the noise is smooth, and also why it is positive when the signal is small (giving the impression of a longer tail). For this reason it is crucial to check the noise level by using a similar filter off resonance (as in the examples of Fig. 2c).
For the Gaussian fit to the Fig. 2c autocorrelation data (blue points), the FWHM was a free parameter (along with the height and centre). For the fit to the Ramsey data of Fig. 2c (red points), the sum of two Gaussians was used, but one Gaussian had its parameters fixed equal to the autocorrelation fit, and the other (red line) had its centre fixed equal to the autocorrelation centre with its width and height free.
The Gaussian line-shapes in Figs 3d,e and 4 are all self-consistent: the raw fringe data of Fig. 3b,c were fitted with a sinusoidal fringe pattern having a Gaussian envelope (on top of a background produced by smoothing the data). By fitting only the raw data, instead of the envelopes produced by the FT filtering, we avoid the effects of Ricean noise on the fits (so the fitted envelopes go to zero at large delays as expected). These fits are not shown in Fig. 3b,c (for clarity), but their envelopes are shown in Fig. 3d,e. For the frequency domain (Fig. 4), FTs were applied to the Gaussian fringe fits without further free parameters. In the case of the red and blue curves/points in Fig. 4, the absolute magnitude of the FT (proportional to the power spectrum for an autocorrelation) is shown. In the case of the green curve/points, the magnitude squared of the FT (proportional to the spectral power in a cross-correlation by a short pulse) is shown.
The preparation pulse area A1 is proportional to where tp is the pulse duration (which is simply proportional to ΔτL for bandwidth-limited pulses) and F10 is the fluence (energy per unit area) at the centre of the beam spot. Using the dipole moment of ex12 where x12=0.28 nm for the 1s(A1) to 2p0 transition15, a π-pulse with ΔτL=5.7 ps and a Gaussian spatial profile with e-folding radius of 1 mm occurs with F10=0.3 μJ cm−2 (note that this is the fluence outside the sample, and we have taken account of the losses due to reflection, the dielectric constant, polarization and so on).
How to cite this article: Litvinenko, K. L. et al. Coherent creation and destruction of orbital wavepackets in Si:P with electrical and optical read-out. Nat. Commun. 6:6549 doi: 10.1038/ncomms7549 (2015).
Ramsey, N. F. A molecular beam resonance method with separated oscillating fields. Phys. Rev. 78, 695–699 (1950) .
Ramdas, A. K. & Rodriguez, S. Spectroscopy of the solid-state analogs of the hydrogen-atom—donors and acceptors in semiconductors. Rep. Prog. Phys. 44, 1297–1387 (1981) .
Bowyer, E. T. et al. Picosecond dynamics of a silicon donor based terahertz detector device. Appl. Phys. Lett. 105, 021107 (2014) .
McCamey, D. R., Van Tol, J., Morley, G. W. & Boehme, C. Electronic spin storage in an electrically readable nuclear spin memory with a lifetime >100 seconds. Science 330, 1652–1656 (2010) .
Steger, M. et al. Quantum information storage for over 180 s using donor spins in a 28Si ‘semiconductor vacuum’. Science 336, 1280–1283 (2012) .
Pla, J. J. et al. A single-atom electron spin qubit in silicon. Nature 489, 541–545 (2012) .
Pla, J. J. et al. High-fidelity readout and control of a nuclear spin qubit in silicon. Nature 496, 334–338 (2013) .
Saeedi, K. et al. Room-temperature quantum bit storage exceeding 39 minutes using ionized donors in silicon-28. Science 342, 830–833 (2013) .
Kane, B. E. A silicon-based nuclear spin quantum computer. Nature 393, 133–137 (1998) .
Stoneham, A. M., Fisher, A. J. & Greenland, P. T. Optically driven silicon-based quantum gates with potential for high-temperature operation. J.Phys. Condens. Matter 15, L447–L451 (2003) .
Hollenberg, L. C. L., Wellard, C. J., Pakes, C. I. & Fowler, A. G. Single-spin readout for buried dopant semiconductor qubits. Phys. Rev. B 69, 233301 (2004) .
Planken, P. C. M. et al. Far-infrared picosecond time-resolved measurement of the free-induction decay in GaAs:Si. Phys. Rev. B 51, 9643–9647 (1995) .
Vinh, N. Q. et al. Silicon as a model ion trap: time domain measurements of donor Rydberg states. Proc. Natl Acad. Sci. USA 105, 10649–10653 (2008) .
Litvinenko, K. L. et al. Photon assisted tunnelling in pairs of silicon donors. Phys. Rev. B. 89, 235204 (2014) .
Greenland, P. T. et al. Coherent control of Rydberg states in silicon. Nature 465, 1057–1061 (2010) .
Knippels, G. M. H. et al. Generation and complete electric-field characterization of intense ultrashort tunable far-infrared laser pulses. Phys. Rev. Lett. 83, 1578–1581 (1999) .
Hubers, H.–W. et al. Isotope effect on the lifetime of the 2p0 state in phosphorus-doped silicon. Phys. Rev. B. 88, 035201 (2013) .
Schofield, S. R. et al. Atomically precise placement of single dopants in Si. Phys. Rev. Lett. 91, 136104 (2003) .
Schofield, S. R. et al. Quantum engineering at the silicon surface using dangling bonds. Nat. Commun. 4, 1649 (2013) .
Murdin, B. N. Si:P as a laboratory analogue for hydrogen on high magnetic field white dwarf stars. Nat. Commun. 4, 1469 (2013) .
Heberle, A. P. et al. Coherent control of exciton density and spin. IEEE J. Sel. Top. Quant. Electron 2, 769–775 (1996) .
Mukai, Y., Hirori, H. & Tanaka, K. Electric field ionization of gallium acceptors in germanium induced by single-cycle terahertz pulses. Phys Rev. B. 87, 201202 (2013) .
Steinfeld J. I. ed. Laser Coherence Spectroscopy Plenum Press (1978) .
Shah, J. Ultrafast spectroscopy of semiconductors and semiconductor nanostructures. 1–446 (Springer Series in Solid-State Sciences vol. 115, Springer, (1999) .
We gratefully acknowledge the support of the EPSRC-UK (COMPASSS, grant reference EP/H026622 and COTS, grant reference EP/J017671/1) and the FOM-NL in providing the required beam time on FELIX. B.N.M. is grateful for a Royal Society Wolfson Research Merit Award.
The authors declare no competing financial interests.
About this article
Cite this article
Litvinenko, K., Bowyer, E., Greenland, P. et al. Coherent creation and destruction of orbital wavepackets in Si:P with electrical and optical read-out. Nat Commun 6, 6549 (2015). https://doi.org/10.1038/ncomms7549
Light: Science & Applications (2019)
Scientific Reports (2019)
Nature Photonics (2018)
Coherent superpositions of three states for phosphorous donors in silicon prepared using THz radiation
Nature Communications (2017)
Nature Materials (2015)