Catalysis by gold supported on reducible oxides has been extensively studied, yet issues such as the nature of the catalytic site and the role of the reducible support remain fiercely debated topics. Here we present ab initio molecular dynamics simulations of an unprecedented dynamic single-atom catalytic mechanism for the oxidation of carbon monoxide by ceria-supported gold clusters. The reported dynamic single-atom catalytic mechanism results from the ability of the gold cation to strongly couple with the redox properties of the ceria in a synergistic manner, thereby lowering the energy of redox reactions. The gold cation can break away from the gold nanoparticle to catalyse carbon monoxide oxidation, adjacent to the metal/oxide interface and subsequently reintegrate back into the nanoparticle after the reaction is completed. Our study highlights the importance of the dynamic creation of active sites under reaction conditions and their essential role in catalysis.
Ever since Haruta, Hutchings and others1,2,3 found that nanosized gold particles, supported by metal oxides, were highly reactive for a variety of important catalytic reactions, gold has been widely used as a catalyst. Extensive studies have been devoted to understanding the chemical nature of high reactivity of oxide supported gold (Au) particles4,5,6,7,8,9,10. Though it is generally recognized that the Au–oxide interfacial perimeter plays an important role, the chemical nature of the active sites and the details of the reaction mechanism are still hotly debated. This is partly because of the complexity of the systems, whose reactivity is affected by many factors, such as the structural and electronic properties of Au particles, the electronic interaction between the support and Au particles, the reactants and products, and finite temperature effects4. Nearly all of the theoretical studies on the Au/oxide system were based on carefully selected model clusters of surfaces, where the tendency of Au nanoparticles and surface to exhibit reconstruction, large amplitude motions and disorder at finite temperatures were not fully accounted for. As a prominent example, ceria (CeO2) has been found to be a particularly effective support for gold particles in catalysing reactions such as CO oxidation and water–gas shift reactions9,10. Generally, the high reactivity is attributed to the excellent redox properties of ceria, such as easy formation and diffusion of oxygen defects, high capacity of oxygen storage and release, and facile acceptance/release and transport of excess electrons in a polaronic state derived from a narrow 4f-band9,10. Various studies11,12,13,14 have identified the interface sites between ceria support and gold particles as vital in the catalytic reactions. Recent evidence15,16,17 has led to the claim that the active sites are, in actuality, positively charged single gold atoms bound to the support by O linkages. Furthermore, environmental transmission electron microscopy analyses18 also showed that gold nanoparticles on a CeO2 support change their shapes at the interfacial area in response to alternating oxidizing and reducing atmospheres. These observations highlight the necessity of understanding the nature of reactive sites on ceria-supported Au nanocatalysts, at actual reaction conditions, that is, at elevated temperature and in the presence of dynamic reacting species.
In our recent report19, we showed that a stable, high-symmetry, tetrahedral Au20 cluster on a rutile TiO2 support exhibited liquid-like motion on charge transfer and CO adsorption. The large adsorbate-induced structural reconstruction also allowed for facile transfer of adsorbed CO to the metal/oxide interface, where the CO2 formation reaction occurs. Connected with this phenomenon was the finding that charge transfer between the nanoparticle and support enabled low-energy redox reactions during the catalytic cycle. These ideas motivated us to consider how generalizable these findings are to other reducible oxides and whether other related phenomena could be involved.
In this work, we present results from density functional theory (DFT)-based ab initio molecular dynamics (AIMD) simulations to explore the reactivity and dynamics of ceria-supported Au catalysts for the CO oxidation reaction. Our simulations take into account both the dynamics of atoms in the Au metal particle, ceria support, reactants and products, as well as the excess charge carriers within the partially reduced ceria surface. We find that, in the presence of CO, a cationic Au+-CO species is created. This species migrates directly onto the ceria support and, via a strong coupling with the redox properties of the ceria, it enables low-energy barriers for redox steps in the catalytic cycle. After the catalytic cycle is complete, the Au single atom is reintegrated into the Au nanoparticle, indicating that the actual catalytic species only exists as a transient under operating conditions.
The behaviour of Au particles on a ceria support
As is known, the geometric and electronic properties of Au particles on the oxide support strongly affect the catalytic activity of Au nanocatalyst4,20,21,22,23. Thus, we first performed AIMD simulations for ceria-supported Au20 cluster to illustrate how the finite temperature and the nature of the adsorbed species influence the morphology of gold nanoparticle, before examining the catalytic mechanism and the effect of particle size. Considering the extensive existence of oxygen vacancies on CeO2, we have removed one surface oxygen atom to model a partially reduced CeO2 support, on which we deposited the Au20 cluster, and allowed it to bind to the surface during a 20-ps AIMD trajectory at T=700 K. In a second step, we added an additional eight CO molecules on the cluster and allowed the system to further equilibrate for another 20 ps. This approach guaranteed a well-thermalized and unbiased structural model of CO adsorbed on a CeO2-supported Au20 cluster.
The distribution of the distance of Au atoms relative to the centre-of-mass of the Au20 cluster, P(rcm) shown in Fig. 1a, can be used to characterize the structural fluctuation within each system. For the isolated Au20 cluster in the gas phase, its tetrahedral configuration is retained at the simulation temperature of 700 K, and the P(rcm) exhibits three well-defined peaks clearly separated by zero probability density between them, corresponding to three types of Au atoms. However, when Au20 is supported on a CeO2(111) surface, Fig. 1b, it exhibits a distinct structural reconstruction and loses its tetrahedral configuration, which is manifested in P(rcm) as broader peaks, compared with the isolated Au20 cluster. The particle–surface interaction are strong due to a gold-to-oxide charge transfer, resulting in partially oxidized Au atoms at the interface as evidenced by the appearance of unpaired electrons localized in the upper layer of Ce atoms when the nanoparticle is adsorbed.
The gold nanoparticle, however, shows appreciably enhanced structural flexibility when CO is co-adsorbed. It is found that Au20 exhibits a strong adsorption-induced surface reconstruction and extrudes many low-coordinated sites to bind CO. As a result, the function P(rcm) for the Au nanoparticle exhibits significantly broader peaks with non-zero density between them. We further observed that CO diffusion proceeds in the same way as reported previously for Au/TiO2 (ref. 19); CO does not move freely from one Au site to another, but rather diffuses as an adsorbed Au–CO species (see Fig. 2 and Supplementary Fig. 1). Since CO oxidation is generally reported to happen at the gold-oxide interface, this finding is vital for understanding how the adsorbed CO species is transported to the perimeter site (Fig. 2a–c). These results indicate that the Au nanoparticle is rather flexible in geometry and can change its morphology on CO adsorption, consistent with previous theoretical studies19,24,25,26. However, the ceria-supported system exhibits one unique feature. As shown in Fig. 1, an Au–CO species migrates away from the gold nanoparticle directly onto the ceria support adjacent to the metal/oxide interfacial area. In the function P(rcm) for Au20, the isolated Au atom could also be identified by a peak at around 6.4 Å that is well separated from the rest of the probability function.
To understand the nature of this specific single-Au atom species, we consider its electronic properties with and without CO adsorption. When CO is removed from the isolated Au–CO, the Au atom is readily reintegrated into the Au nanoparticle (see Fig. 3a), even in the course of a simple local geometry optimization. By monitoring the spin density, we observed four excess electrons in the CeO2 lattice, two more than the number that an oxygen defect can create, indicating that the Au nanoparticle transfers additional charges to the surface27. Once the CO is adsorbed at the Au atom, and the Au–CO moiety becomes isolated from the rest of the Au nanoparticle, an additional excess electron becomes localized on an adjacent Ce site in the topmost layer of the support. Concurrently, the charge of this Au atom increases from +0.10 |e| to +0.42 |e| This indicates that by moving to the oxygen site, the single Au atom transfers one electron to the support, resulting in a species that can be formally described as an adsorbed Au+–CO. Our results are consistent with previous findings28,29 that the single Au atom on CeO2 surface can transfer its 6s electron to the unoccupied 4f orbital of Ce. We note that the observed excess electrons are mobile on the AIMD timescale, showing hops between Ce sites in the topmost surface layer on the order of 2 ps, in accord with our previous work on partially reduced ceria30.
owing to the nature of ligand-to-metal electron donation of the Au–CO bond, CO is expected to energetically favour binding at the positively charge Au site. To understand the formation of single Au atom, we further considered the formation energies of the single Au atom with or without CO adsorption:
where E1 is the energy change by taking one Au atom from the Aun nanoparticle to the next-nearest oxygen site on ceria surface and E2 is the energy associated with taking one Au–CO unit from the Aun nanoparticle to the next-nearest oxygen site. Since in our AIMD simulations CO adsorption can only cause a low-coordinated Au atom to be isolated from the Au nanoparticle at the interface, we only consider a single four-coordinated Au site at the interface. For the Au20 cluster on ceria surface, the calculated E1 is 1.21 eV, indicating that for the bare Au nanoparticle it is energetically unfavourable for the Au atom to break away from the Au nanoparticle. While the calculated E2 is −0.81 eV, it indicates that forming an isolated Au+–CO could be thermodynamically favourable. Our work is consistent with the recent findings31 that CO adsorption on a CeO2-supported Au4 cluster leads to the formation of Au–CO species. Considering the CO oxidation on CeO2-supported Au nanoparticles is reported to proceed at room temperature4,32, we further considered the possible reaction paths for Au–CO dissociation into the adjacent oxygen site on Au20/CeO2 using climbing image nudged-elastic-band method (see Supplementary Fig. 2). The barrier is estimated to be ~0.20–0.62 eV, which indicates that the isolated Au–CO can easily be form at room temperature. Combined with the fact that Au–CO species on the Au cluster are mobile (Fig. 2), we also conclude that even if CO does not initially adsorb directly at the interface site, the isolated Au+–CO will eventually form.
Inasmuch as in our previous simulation19 we did not observe any isolated Au–CO on TiO2 support, we checked the single-atom formation energies on Au20/TiO2 system. The isolated Au atom without adsorbed CO is not stable at the oxygen site and slips to the adjacent five-coordinated Ti site spontaneously during the geometry optimization, in accord with Metiu’s recent report33,34. However, its formation energies are positive (E2=1.25 eV at the oxygen site; E1=0.96 eV and E2=0.90 eV at the Ti site), implying that stabilizing the oxidized Au+–CO on a TiO2 support is unfavourable. This is traced back to the fact that rutile TiO2 is less capable of accepting an electron from an Au–CO to stabilize a cationic species and highlights the point that the CeO2 support, as a stronger oxidizer, can.
Generally, the reactivity for an oxidation reaction is strongly affected by the electronic chemical potential (work function, W) of the catalyst. We found that creation of the isolated Au+–CO increased W from 4.8 to 5.1 eV, which indicates that the Ceria is more likely to take electrons by becoming a stronger oxidizing agent, and it is itself more easily reduced. This implies that the single Au atom at the interfacial area creates an activation centre for oxidation processes and, thus, is expected to be more reactive, in accord with recent reports on highly reactive single-atom catalysts on metal oxide35,36. In the next section, we further consider the possible reaction mechanism for CO oxidation at the isolated Au species on CeO2 surface and directly compare with the process at the cluster/oxide interface
Reaction mechanism for CO oxidation
Recent theoretical studies have proposed9,14,37 three CO oxidation mechanisms on CeO2-supported Au particles: (1) CO oxidation by co-adsorbed O2 on Au particles, (2) CO oxidation by adsorbed O2 at the interfacial site and (3) CO oxidation by a lattice oxygen ion from CeO2 substrate. In the present study, we examined a large number of adsorption configurations of O2 on Au20 cluster or interfacial sites, but we found that the O2 hardly binds at these sites (Eads<−0.2 eV). These results suggest that CO oxidation with preadsorbed O2 at the Au nanoparticle or the interface sites are less likely to be operative for larger Au particles, and lower reduction levels of the support, as is expected to be the case for a reaction that is run under oxidizing conditions. Therefore, we consider the reaction of CO with the lattice oxygen ion, in accord with extensive experimental studies18,38,39,40 that strongly indicate that CO oxidation proceeds via a Mars-van Krevelen mechanism (that is, a redox) mechanism.
We first considered the oxidation of CO that preadsorbs on the gold nanoparticle, comparable with previous theoretical studies14. The detailed pathways and energetics are shown in Supplementary Fig. 3. We found that CO easily reacts with the lattice oxygen ion, and forms a bent CO2− intermediate. This is a highly exothermic process (ΔE=−0.94 eV) with a low-energy barrier (ΔE†=0.25 eV). However, the subsequent CO2 desorption is quite unfavourable, with a desorption energy of 1.29 eV. As the lattice oxygen ion is being extracted, there is a concurrent reduction of the surface that leaves two excess electrons localized on the Ce 4f states. After the formation of an oxygen defect, O2 adsorption from the gas phase at this site is highly favourable in energy and the subsequent oxidization of the second CO to CO2 proceeds with a low-energy barrier (ΔE†=0.45 eV). Overall, the rate determining step for the oxidation of CO preadsorbing on the gold particle involves desorption of the first CO2 with a high-enough energy barrier such that the reaction would not be anticipated to proceed at room temperature. However, the result is in direct contradiction with the experimental findings32,41 that show the reaction of CO oxidation with lattice oxygen ion in the interfacial area at the room temperature. In short, for the current Au20 system on a mildly reduced ceria support, none of the three previously proposed routes corroborate this experimental observation.
As the adsorption of CO at the perimeter sites could lead to the formation of an Au+–CO near the interfacial area, we further consider the reaction mechanism for CO oxidation at this specific isolated site. The reaction pathway and associated energetics are shown in Fig. 4. For convenience of discussion, we also track the Bader charges of the isolated Au and the number of Ce3+ throughout the catalytic process for each stationary point on the potential energy surface, shown in Table 1. In the proposed mechanism, we start the reaction process from the Au nanoparticle without an isolated Au site (Configuration i in Fig. 4). First, the adsorption of CO at the low-coordinate site leads to the formation of an isolated Au+–CO unit (Configuration ii). By overcoming a barrier of 0.77 eV, the CO can react with the adjacent oxygen ion, forming a bent CO2− intermediate (Configuration iii). Further, this bent intermediate only requires 0.27 eV of energy to release the CO2 molecule into the gas phase (Configuration iv). In this process, the single Au atom migrates towards and occupies the oxygen defect after CO2 desorption. The Bader charge of the Au atom significantly decreases from +0.40 to −0.56, while the number of Ce3+ ions remains unchanged. These results indicate that in tandem with the removal of the lattice oxygen ion, the two resulting excess electrons are transferred to the single Au atom, leading to a conversion of the oxidation state from Au+ to a Au− that fills the oxygen vacancy. In other words, this single atom stabilizes the reduction of the ceria surface leading to more facile CO2 desorption. This observation is consistent with our previous analysis of work function, which suggests in the presence of a charged Au++CO, Ceria is locally a stronger oxidizing agent. However, the resulting Au− species, which fills the oxygen vacancy, is in direct contrast with the CO oxidation on the Au nanoparticle where the two resulting excess electrons become localized at two Ce3+ ions.
To complete the catalytic cycle, we consider the second half of the CO oxidation reaction. Once the single Au atom has moved into the oxygen defect, it is harder to bind CO (Eads=−0.16 eV) or O2 (Eads=−0.10 eV) molecules. At first glance, this would indicate that the catalyst is deactivated for further CO oxidation, which is consistent with a recent study17 showing that Au at the oxygen defect has no further reactivity for CO oxidation. However, further CO oxidation can be achieved by extracting the Au atom out of the vacancy back to the Au cluster, so that it could bind the second CO while the vacancy becomes available for O2 adsorption. We noted that our AIMD simulations for Au20/CeO2 with one oxygen vacancy did not show any Au atom permanently occupying the oxygen vacancy, which implies that it may also be possible that the single Au atom may be able to reintegrate with the Au cluster (Configuration vi). With this in mind, we further performed CI-NEB calculations, as well as, constrained AIMD computation of a potential of mean force for the single Au reintegrating into the Au cluster without the presence of CO. We found that the single Au atom, at the oxygen vacancy, can move up and reintegrate within into Au cluster with a barrier of 0.89 eV on the potential energy surface and 0.81 eV on the free energy surface. This process is slightly exothermic with Au preferring energetically to be reintegrating into the Au cluster by −0.10 eV. Note these relatively low barriers are consistent with room temperature activity. Once the Au is back to the Au cluster, the second CO can form another stable Au+–CO species near the interfacial area (Configuration vii), by exothermic adsorption energy of −1.12 eV. During these processes, the Bader charge of the single Au atom increases from −0.54 to 0.40 e−. The surface accumulates two more Ce3+ ions, indicating that by moving out of the oxygen defect, the Au ion returns two excess electrons to the lattice. This result implies that the driving force for the Au moving out of the oxygen defect comes from the attraction of the Au cluster, and it also explains the recent experimental findings42,43 that the clustering of Au from an isolated Au precursor results in an increase of the CO oxidation activity. Recent theoretical studies17,31 also showed that the small Aun cluster (Au2 or Au3) are catalytically reactive for CO oxidation without filling one Au into the oxygen defect site. Since the oxygen vacancy is recreated, the O2 molecule in the gas phase could easily fill into the oxygen defect with a high binding energy of −1.51 eV, eliminating the two excess electrons and forming a peroxo O22− species (Configuration viii). As a result, the CO at the single Au site only needs to overcome a small barrier of 0.65 eV to react with the peroxo O22− species, releasing the second CO2 (Configuration ix). During this process, the Au atom gradually loses its adsorbed CO and returns to the Au nanoparticle, completing the catalytic cycle. Overall, the proposed mechanism suggests that the rate-limiting step for CO oxidation is the removal of the single Au out of the oxygen vacancy. The barrier of the rate-limiting step at the single atom site is 0.89 eV, which is far lower than that at the gold particles (1.29 eV), suggesting that the transient monatomic species are the active sites in CeO2-supported Au catalyst.
For a direct comparison with the experimental observation for the room temperature CO oxidation32,41, we made a simple estimation of the reaction rate in the form of an attempt frequency multiplied by a Boltzmann factor, that is, ν=ν0exp(−Ea/kBT) and assuming ν0=1013 s−1, a reasonable value for most oxides as suggested by Marrochelli and Yildiz44. From this formula, the range of temperatures at which the reaction process could occur, within a minimum range of rate constant 0.01~1 s−1, are estimated to be 300–340 K, consistent with room temperature activity. We also performed constrained MD simulations to obtain the free energy barrier at 300 K for the migration of the Au atom towards the Au cluster (Supplementary Fig. 5). This simulation allows for the sampling of collective motions, such as the restructuring of the entire Au particle on reintegration of the Au ad-atom, and thus would be expected to better account for both the energy and entropic components of the process. The free energy barrier is estimated to be 0.81 eV and based on the transition state theory formalism ν=kBT/h exp(−ΔG†/kBT) the rate constant at 300 K is estimated to be 0.1 s−1, indicating that the process could occur several times per minute at room temperature.
Above, we proposed that the Au cluster could drive the Au atom out of the vacancy. We also noted that an isolated Au atom at the oxygen defect could also be directly pulled out of the oxygen defect by an adsorbed CO, with a barrier of 0.85 eV, and a highly exothermic reaction energy of −1.06 eV. Since the initially CO adsorption is very weak (only −0.16 eV), this process will resemble an Eley–Rideal mechanism (the energy barrier is 0.85–0.16=0.69 eV) with a relatively low rate at reaction conditions where CO oxidation is typically performed. However, it may still happen under CO-rich conditions, where the high partial pressure of CO would significantly increase the sticking possibility of CO at the single Au site, and would enhance the reaction probability for the second CO oxidation step without changing the subsequent steps in reaction mechanism. In addition, recent theoretical studies by Song et al.45,46 also proposed a relevant mechanism for CO oxidation and propylene oxidation at an isolated Au site, which are compatible with our findings.
Since the single Au atom is induced by CO adsorption at the interfacial area, it is its mobility that ultimately determines where the CO oxidation proceeds. In Supplementary Fig. 6, we show the reaction paths and energetics for Au diffusion to another oxygen site away from the Au nanoparticle. With the adsorption of CO, the single Au atom has to overcome a high barrier of 1.14 eV to diffuse from the interface to the next oxygen site, indicating that the diffusion of Au–CO unit on the ceria surface is improbable at ambient conditions. As the barrier for CO reacting with the lattice oxygen is smaller (0.77 eV) than the diffusion barrier, the Au+–CO is expected to oxidize appreciably faster than it can diffuse. We further consider a single Au atom away from the Au nanoparticle without CO adsorption. Similarly, the barrier for the diffusion away from the interface is much higher (1.59 eV). Especially, when considering the inverse diffusion, the Au atom at the oxygen site only needs to overcome a very low barrier of 0.37 eV to diffuse back towards the Au nanoparticle. The process is highly exothermic with a reaction energy of −1.22 eV and is the result of the above-mentioned propensity for the Au atoms to reintegrate with the nanoparticle when CO is not present. Taken together, these results demonstrate that single Au atom catalysis for CO oxidation would occur predominantly at the interfacial area.
Nanoparticle size effects
Since our AIMD simulations for Au20/CeO2 only show the formation of the isolated Au+–CO species at the low-coordinated sites, one may ask if the formation of the isolated Au+–CO species is determined by the specific model cluster and how applicable are these findings to large Au particles. Therefore, we further performed AIMD simulations for a bigger Au50 cluster (~1.5 nm) on CeO2 support, which initially had no low-coordinate site at the interface area, shown in Fig. 5. We observed that the low-coordinate sites formed at the interface area, revealing that for even 1 nm Au particles, or larger, the low-coordination sites should always exist at the interface. We further considered the formation energy of the isolated Au–CO species on the CeO2 surface. In Table 2, we list the single-Au formation energies for Au10, Au20 and Au50. Without CO adsorption, the formation energies are endothermic for all three Au clusters, indicating that the creation of an isolated Au ad-atom is energetically unfavourable in all cases. Conversely, in the presence of CO, the adsorption energies at isolated Au+ sites for all clusters become exothermic, illustrating how formation of this species near the metal/oxide interface becomes thermodynamically favourable. We find that the above-mentioned formation energies are all within the same energy range with a variance of 0.3 eV and no discernible trend indicating that this general result is not particularly influenced by the cluster size. We further performed a short (~5 ps) AIMD simulation for CeO2-supported Au10 and Au50, where CO molecules are initial located at a low-coordination interfacial Au site, to compare with our Au20 results. In agreement with our analysis above, we observe spontaneous formation of an Au++CO atom at the interface for both cases within only a few ps, see Fig. 5c and Supplementary Fig. 7.
In summary, we find that, for both smaller and larger Au nanoparticles, the surface-adsorbed Au+−–CO can be formed readily by CO adsorption. We speculate that under realistic conditions, small-size Au particles, with potentially a higher ratio of low coordinate sites at the interface than the large particles, should produce more single Au atom on CO adsorption. This conclusion is also consistent with our AIMD simulations on Au10/CeO2 with four adsorbed CO molecules, where we observed two single-Au atoms at the interface (Supplementary Fig. 7).
In the present study, we performed static DFT calculations and ab initio molecular dynamic simulations to gain insight on the reaction mechanism of CO oxidation at the interfacial area. A new, dynamic, single-atom catalytic mechanism is established for CO oxidation on Au/CeO2 catalysts, arising from a transient Au+–CO species. During the reaction process, a single Au+ atom acts as charge acceptor for enhanced CO adsorption and transport. This species considerably lowers the barriers for CeO2 reduction, effectively promoting the CO oxidation reaction. However, the active species, an Au+–CO ion, emerges only in the presence of CO, and otherwise reintegrates with the Au nanoparticle. It is this monoatomic species that is able to couple its redox processes effectively with those of the support to enhance the redox processes, whilst the Au nanoparticle shows little evidence of coupling of its charge state with that of the oxide during the catalytic cycle.
Our study touches on a very important concept in the heterogeneous catalysis, namely that the actual catalytic active centre may be created only under reaction conditions and may not necessarily be easy to identify ex situ. The current study adds a layering to this concept by suggesting that, in the present case, the formation of the active site is a dynamic process occurring at the support oxide/metal particle interface. Our results promote the concept that the dynamic behaviour induced by the reactants at the interfacial area may be an overlooked aspect on the catalysis on reducible supports.
All DFT calculations were performed using the CP2K package47. The exchange-correlation energy was described by the generalized-gradient approximation with spin-polarized Perdew–Burke–Ernzerh functional48. The wavefunctions were expanded in an optimized double-ζ Gaussian basis sets30,49 with an auxiliary plane wave basis set with a cutoff energy of 500 Rydberg50. Core electrons have been modelled by scalar relativistic norm-conserving pseudo potentials51 with 12, 6, 1 and 4 valence electrons for Ce, O, H and C, respectively. Brillouin zone integration is performed with a reciprocal space mesh consisting of only the gamma point. The DFT+U method, based on the Mullikan 4f state population analysis, was used to describe the Ce 4f electrons. A U value of 7.0 eV was used to reproduce the correct band gap of 3.2 eV, gap state location of 1.3 eV above the valence band, and work function of 4.6 eV for CeO2, which ensure that the redox chemistry is reproduced correctly. The detail tests and discussion can be found in our recent study30 and in the Supplementary methods. We observed many localized 4f electrons on CeO2-supported Au clsuter, which are mobile and can be localized at many different Ce sites in the simulations. This may lead to 0.1–0.3 eV difference for the energetics, as is discussed in our previous study30. The location and energy of the transition state was performed using the climbing image nudged-elastic-band method (CI-NEB)52,53 including 9 replicas. The convergence criterion for the maximum force is set as 2 × 10−3 atomic units. Vibrational analysis was further used to confirm the transition states corresponded to true saddle points on the potential energy surface with only one imaginary frequency.
The CeO2(111)-p(5 × 6) surface with one oxygen defect was used to model the CeO2 substrate, consisting of 4 O-Ce-O tri-layers (12 atomic layers), and only the bottom Ce atomic-layer were frozen while the remaining layers were allowed to relax. The slab was repeated periodically with a vacuum layer of 20 Å in the direction of the surface normal. A tetrahedral Au20 cluster, which has been well characterized in previous studies, was chosen to model Au particles. The benchmark test of current approach with respect to a family of Au20 isomers can be found in our recent study19. To consider the nanoparticle size effect, Au10 (planar) and Au50 cluster were chose to model the different size of gold nanoparticles (the coordinates are listed in Supplementary Data 1).
All ab initio MD simulations were performed by sampling the canonical ensemble employing Nose–Hoover thermostats54,55 with a time step of 0.5 fs at a finite temperature of 300 or 700 K. On the basis of simple geometry optimization, CeO2-supported Au20 cluster is estimated to be able to bind up to 10 CO molecules and the average binding energy is 0.87 eV per CO. This result is consistent with our recent study19 on TiO2-supported Au20 cluster where we also found the system can at most bind 10 CO. Therefore, in our MD simulations, we considered both low coverage and high coverage of CO on the Au cluster to explore the behaviour of CO-induced reconstruction. Since the relatively short timescales of AIMD limit sampling to only very fast, low-energy barrier events and preclude the observation of slow processes, the high temperature simulations could more rapidly explore a large volume of phase space. On the basis of a simple estimation according to 1013*exp(−Ea/RT), the rate constant for a reaction with an energy barrier of 0.5 eV at 700 K is around 0.0025, ps−1, this means that the process can happen only one time every 400 ps. Therefore, only the reaction process with the energy barrier lower than 0.5 eV may be observed in our MD simulations at 700 K due to the limitation of the timescale (10–30 ps).
How to cite this article: Wang, Y.-G. et al. Dynamic formation of single-atom catalytic active sites on ceria-supported gold nanoparticles. Nat. Commun. 6:6511 doi: 10.1038/ncomms7511 (2015).
Haruta, M., Kobayashi, T., Sano, H. & Yamada, N. Novel gold catalysts for the oxidation of carbon monoxide at a temperature far below 0°C. Chem. Lett. 2, 405–408 (1987).
Haruta, M. Size-and support-dependency in the catalysis of gold. Catal. Today 36, 153–166 (1997).
Hutchings, G. J. Gold catalysis in chemical processing. Catal. Today 72, 11–17 (2002).
Hvolbæk, B. et al. Catalytic activity of Au nanoparticles. Nano Today 2, 14–18 (2007).
Vilhelmsen, L. B. & Hammer, B. Identification of the catalytic site at the interface perimeter of au clusters on rutile TiO2(110). ACS Catal. 4, 1626–1631 (2014).
Green, I. X., Tang, W., Neurock, M. & Yates, J. T. Jr Insights into catalytic oxidation at the Au/TiO2 dual perimeter sites. Acc. Chem. Res. 47, 805–815 (2013).
Wang, J. & Hammer, B. Oxidation state of oxide supported nanometric gold. Top. Catal. 44, 49–56 (2007).
Farnesi Camellone, M. & Marx, D. Nature and role of activated molecular oxygen species at the gold/titania interface in the selective oxidation of alcohols. J. Phys. Chem. C 118, 20989–21000 (2014).
Zhang, C., Michaelides, A. & Jenkins, S. J. Theory of gold on ceria. Phys. Chem. Chem. Phys. 13, 22–33 (2010).
Paier, J., Penschke, C. & Sauer, J. Oxygen defects and surface chemistry of ceria: quantum chemical studies compared to experiment. Chem. Rev. 113, 3949–3985 (2013).
Rodriguez, J. A. Gold-based catalysts for the water–gas shift reaction: active sites and reaction mechanism. Catal. Today 160, 3–10 (2011).
Zhou, Z., Kooi, S., Flytzani-Stephanopoulos, M. & Saltsburg, H. The role of the interface in CO Oxidation on Au/CeO2 multilayer nanotowers. Adv. Funct. Mater. 18, 2801–2807 (2008).
Longo, A. et al. Structure of the metal–support interface and oxidation state of gold nanoparticles supported on ceria. J. Phys. Chem. C 116, 2960–2966 (2011).
Kim, H. Y., Lee, H. M. & Henkelman, G. CO oxidation mechanism on CeO2-Supported Au nanoparticles. J. Am. Chem. Soc. 134, 1560–1570 (2012).
Guan, Y. & Hensen, E. Cyanide leaching of Au/CeO2: highly active gold clusters for 1, 3-butadiene hydrogenation. Phys. Chem. Chem. Phys. 11, 9578–9582 (2009).
Flytzani-Stephanopoulos, M. Gold atoms stabilized on various supports catalyze the water–gas shift reaction. Acc. Chem. Res. 47, 783–792 (2013).
Camellone, M. F. & Fabris, S. Reaction mechanisms for the CO oxidation on Au/CeO2 catalysts: Activity of substitutional Au3+/Au+ cations and deactivation of supported Au+ adatoms. J. Am. Chem. Soc. 131, 10473–10483 (2009).
Ta, N. et al. Stabilized gold nanoparticles on ceria nanorods by strong interfacial anchoring. J. Am. Chem. Soc. 134, 20585–20588 (2012).
Wang, Y.-G., Yoon, Y., Glezakou, V.-A., Li, J. & Rousseau, R. The role of reducible oxide–metal cluster charge transfer in catalytic processes: new insights on the catalytic mechanism of CO oxidation on Au/TiO2 from ab initio molecular dynamics. J. Am. Chem. Soc. 135, 10673–10683 (2013).
Lopez, N. & Nørskov, J. K. Catalytic CO oxidation by a gold nanoparticle: a density functional study. J. Am. Chem. Soc. 124, 11262–11263 (2002).
Yoon, B. et al. Charging effects on bonding and catalyzed oxidation of CO on Au8 clusters on MgO. Science 307, 403–407 (2005).
Remediakis, I. N., Lopez, N. & Nørskov, J. K. CO oxidation on rutile‐supported Au nanoparticles. Angew. Chem. In. Ed. 117, 1858–1860 (2005).
Gates, B. C. Supported gold catalysts: new properties offered by nanometer and sub-nanometer structures. Chem. Commun. 49, 7876–7877 (2013).
Pal, R. et al. Chemisorption-Induced 2D–3D–2D structural transitions in gold heptamer:(CO)nAu7–(n= 1–4). J. Phys. Chem. Lett. 2, 2288–2293 (2011).
Li, W.-K., Chu, L.-N., Gong, X.-Q. & Lu, G. A comparative DFT study of adsorption and catalytic performance of Au nanoparticles at anatase and brookite TiO2 surfaces. Surf. Sci. 605, 1369–1380 (2011).
Zhai, H. J. et al. Chemisorption-induced structural changes and transition from chemisorption to physisorption in Au6(CO)n−(n= 4− 9). J. Phys. Chem. C 112, 11920–11928 (2008).
Zhang, C., Michaelides, A., King, D. A. & Jenkins, S. J. Positive charge states and possible polymorphism of gold nanoclusters on reduced ceria. J. Am. Chem. Soc. 132, 2175–2182 (2010).
Liu, Z. P., Jenkins, S. J. & King, D. A. Origin and activity of oxidized gold in water-gas-shift catalysis. Phys. Rev. Lett. 94, 196102 (2005).
Zhang, C., Michaelides, A., King, D. A. & Jenkins, S. J. Structure of gold atoms on stoichiometric and defective ceria surfaces. J. Chem. Phys. 129, 194708 (2008).
Wang, Y.-G., Mei, D., Li, J. & Rousseau, R. DFT+U study on the localized electronic states and their potential role during H2O dissociation and CO oxidation processes on CeO2(111) surface. J. Phys. Chem. Lett. 4, 2256–2363 (2013).
Ghosh, P., Camellone, M. & Fabris, S. Fluxionaality of Au clusters at ceria surfaces during CO oxidation: relationships among reactivity, size, cohesion, and surface defects from DFT simulations. J. Phys. Chem. C 117, 23082–23089 (2013).
Zhang, S. et al. CO oxidation activity at room temperature over Au/CeO2 catalysts: disclosure of induction period and humidity effect. ACS Catal. 4, 3481–3489 (2014).
Chrétien, S. & Metiu, H. Density functional study of the interaction between small Au clusters, Aun (n= 1–7) and the rutile TiO2 surface. II. Adsorption on a partially reduced surface. J. Chem. Phys. 127, 244708 (2007).
Chrétien, S. & Metiu, H. Density functional study of the charge on Aun clusters (n=1–7) supported on a partially reduced rutile TiO2 (110): are all clusters negatively charged? J. Chem. Phys. 126, 104701 (2007).
Qiao, B. et al. Single-atom catalysis of CO oxidation using Pt1/FeOx. Nat. Chem. 3, 634–641 (2011).
Yang, X.-F. et al. Single-Atom catalysts: a new frontier in heterogeneous catalysis. Acc. Chem. Res. 46, 1740–1748 (2013).
Song, W. & Hensen, E. J. M. A computational DFT study of CO oxidation on a Au nanorod supported on CeO2(110): on the role of the support termination. Catal. Sci. Technol. 3, 3020–3029 (2013).
Shapovalov, V. & Metiu, H. Catalysis by doped oxides: CO oxidation by AuxCe1−xO2 . J. Catal. 245, 205–214 (2007).
Widmann, D., Leppelt, R. & Behm, R. Activation of a Au/CeO2catalyst for the CO oxidation reaction by surface oxygen removal/oxygen vacancy formation. J. Catal. 251, 437–442 (2007).
Qian, K. et al. Influences of CeO2 microstructures on the structure and activity of Au/CeO2/SiO2 catalysts in CO oxidation. J. Mol. Catal. A-Chem. 306, 40–47 (2009).
Deng, W., Carpenter, C., Yi, N. & Flytzani-Stephanopoulos, M. Comparison of the activity of Au/CeO2 and Au/Fe2O3 catalysts for the CO oxidation and the water-gas shift reactions. Top. Catal. 44, 199–208 (2007).
Aguilar-Guerreroa, V. & Gates, B. C. Genesis of a highly active cerium oxide-supported gold catalyst for CO oxidation. Chem. Commun. 30, 3210–3212 (2007).
Aguilar-Guerrero, V., Lobo-Lapidus, R. J. & Gates, B. C. Genesis of a cerium oxide supported gold catalyst for CO oxidation: transformation of mononuclear gold complexes into clusters as characterized by X-ray absorption spectroscopy. J. Phys. Chem. C 113, 3259–3269 (2009).
Marrocchelli, D. & Yildiz, B. First-principles assessment of H2S and H2O reaction mechanisms and the subsequent hydrogen absorption on the CeO2(111) surface. J. Phys. Chem. C 116, 2411–2424 (2012).
Song, W. & Hensen, E. J. M. Structure sensitivity in CO oxidation by a single Au atom supported on ceria. J. Phys. Chem. C 117, 7721–7726 (2013).
Song, W. et al. Selective propylene oxidation to acrolein by gold dispersed on MgCuCr2O4 spinel. ACS. Catal. 5, 1100–1111 (2015).
VandeVondele, J. et al. Quickstep: fast and accurate density functional calculations using a mixed Gaussian and plane waves approach. Comp. Phys. Commun. 167, 103–128 (2005).
Perdew, J. P., Burke, K. & Ernzerhof, M. Generalized gradient approximation made simple. Phys. Rev. Lett. 77, 3865–3868 (1996).
VandeVondele, J. & Hutter, J. Gaussian basis sets for accurate calculations on molecular systems in gas and condensed phases. J. Chem. Phys. 127, 114105 (2007).
Lippert, B. G., Hutter, J. & Parrinello, M. A hybrid Gaussian and plane wave density functional scheme. Mol. Phys. 92, 477–488 (1997).
Goedecker, S., Teter, M. & Hutter, J. Separable dual-space Gaussian pseudopotentials. Phys. Rev. B 54, 1703–1710 (1996).
Mills, G., Jónsson, H. & Schenter, G. K. Reversible work transition state theory: application to dissociative adsorption of hydrogen. Surf. Sci. 324, 305–337 (1995).
Henkelman, G., Uberuaga, B. P. & Jónsson, H. A climbing image nudged elastic band method for finding saddle points and minimum energy paths. J. Chem. Phys. 113, 9901 (2000).
Nosé, S. A unified formulation of the constant temperature molecular dynamics methods. J. Chem. Phys. 81, 511 (1984).
Hoover, W. G. Canonical dynamics: equilibrium phase-space distributions. Phys. Rev. A 31, 1695–1697 (1985).
This work was supported by the US Department of Energy, Office of Science, Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences & Biosciences and performed at Pacific Northwest National Laboratory (PNNL). PNNL is a multi-programme national laboratory operated by Battelle for the US Department of Energy. J.L. and Y.-G.W. were also financially supported by NKBRSF (2011CB932400) and NSFC (91026003, 21101098) of China. Computational resources were provided at W.R. Wiley Environmental Molecular Sciences Laboratory (EMSL), a national scientific user facility located at PNNL and sponsored by the US Department of Energy, Office of Science, Office of Biological and Environmental Research and at the National Energy Research Scientific Computing Center (NERSC) located at Lawrence Berkeley National Laboratory.
The authors declare no competing financial interests.
Supplementary Figures 1-7, Supplementary Methods and Supplementary References (PDF 823 kb)
Coordinates and energies of all stationary points on the potential energy surface (DOC 335 kb)
About this article
Cite this article
Wang, YG., Mei, D., Glezakou, VA. et al. Dynamic formation of single-atom catalytic active sites on ceria-supported gold nanoparticles. Nat Commun 6, 6511 (2015). https://doi.org/10.1038/ncomms7511
Valence state of transition metal center as an activity descriptor for CO2 reduction on single atom catalysts
Journal of Energy Chemistry (2021)
Science China Materials (2021)
Structural evolution of MoS2 supported gold nanoclusters under CO oxidation condition and the effect on reaction activity
Applied Surface Science (2021)
Strain engineering to tune the performance of CO oxidation on Cu2O(1 1 1) surface: A theoretical study
Applied Surface Science (2021)
Advanced Energy Materials (2021)