Passive photonic crystals have been shown to exhibit a multitude of interesting phenomena, including slow-light propagation in line-defect waveguides. It was suggested that by incorporating an active material in the waveguide, slow light could be used to enhance the effective gain of the material, which would have interesting application prospects, for example enabling ultra-compact optical amplifiers for integration in photonic chips. Here we experimentally investigate the gain of a photonic crystal membrane structure with embedded quantum wells. We find that by solely changing the photonic crystal structural parameters, the maximum value of the gain coefficient can be increased compared with a ridge waveguide structure and at the same time the spectral position of the peak gain be controlled. The experimental results are in qualitative agreement with theory and show that gain values similar to those realized in state-of-the-art semiconductor optical amplifiers should be attainable in compact photonic integrated amplifiers.
Slow light is a fascinating physical effect, raising fundamental questions related to our understanding of light–matter interactions as well as offering new possibilities for photonic devices. From the first demonstrations of slow-light propagation in ultra-cold atomic gasses1, solid-state Ruby2 and photonic crystal (PhC) structures3, focus has shifted to applications, with slow light offering the ability to enhance and control light–matter interactions. The demonstration of tuneable delay lines4,5,6, enhanced nonlinearities7,8 and spontaneous emission9, enlarged spectral sensitivity10 and increased phase shifts illustrate the possibilities enabled by slow-light propagation, with microwave photonics emerging as one of the promising applications11.
Stimulated emission of radiation leads to the amplification of a propagating electromagnetic wave, forming the basis for optical amplifiers and lasers. The strength of the process is quantified by the gain coefficient per unit length, and is usually considered to be governed by the material properties. Dowling et al.12 suggested that the slow down of light near the edge of a one-dimensional photonic bandgap structure could be used to enhance the gain coefficient. The slow propagation of the Bloch mode near the band edge, which may be visualized as multiple back-and-forth scattering of the light beam, thus lengthens the local dwell time in the medium and increases the spatial but not the temporal gain coefficient13. Despite obvious applications in optical amplifiers14,15 and lasers16, there is no conclusive experimental demonstration in a waveguide structure. For dye-doped three-dimensional artificial opals, enhancement of gain in certain crystallographic directions and its relation to the directional density of optical states was demonstrated17, and in ref. 18 enhancement effects in multimode InP waveguides related to a ministop band were indicated. Spontaneous emission enhancement was observed in PhC wires19 and dielectric multilayers with oxygen vacancies as light emitters20, and may be used to increase the spontaneous emission factor of a waveguide9. Early measurements on lasers employing PhC waveguides21,22 and coupled resonator structures23 show that the lasing characteristics are improved using slow-light effects. However, as both the cavity quality factor and the spatial gain coefficient may be affected by slow-light propagation, laser measurements cannot easily distinguish between the two effects. Thus, measurements on open structures are required.
In this study we experimentally demonstrate that the gain of an active waveguide can indeed be enhanced using slow-light effects in PhCs, enabling compact linear and nonlinear devices suitable for photonic integration, as well as providing opportunities for spectral and spatial control of the gain. The effect was theoretically predicted but not yet experimentally demonstrated. The maximum achievable gain is limited by amplified spontaneous emission, as well as multiple-scattering and localization due to disorder.
Theory of slow-light-enhanced gain
Before describing our experimental results, we briefly summarize the theoretical status. An extensive analysis for a periodic PhC lattice shows that the gain scales with the density of optical states16. For a one-dimensional defect waveguide, based on qualitative considerations of the effective path length, Dowling et al.12 suggested a linear scaling of gain with group index. By expansion into Bloch waves, we derived the following approximate expression for the modal gain coefficient (see Supplementary Methods)
with gmat being the material gain, g0 the bare material gain in absence of a PhC waveguide, ng the group index, nb the background refractive index of the active material and Γ a generalized confinement factor describing the field overlap with the active material. The importance of the latter was demonstrated experimentally in absorption-type measurements24. Equation (1) agrees with the result of a perturbative analysis25. The predicted scaling of the modal gain (or absorption) with group index has, despite its intuitive appeal, been the subject of some controversy, and it was shown that one needs to distinguish between slow light originating from structural perturbations, for example a PhC waveguide, and material dispersion, such as electromagnetically induced transparency26. For the latter, equation (1) does not hold, as also demonstrated experimentally27. Moreover, for translationally invariant systems, such as a fibre, the gain enhancement due to slow light induced by mode dispersion is exactly cancelled by the resulting transversal expansion of the mode26.
To confirm equation (1) and quantify the impact of slow light on the modal gain, we carried out extensive calculations of gain spectra in different structures, see Fig. 1. As the mode frequency (Fig. 1a) approaches the band edge, the group index (Fig. 1b) of the PhC waveguide strongly increases, leading to a significant increase of the modal gain coefficient of the corresponding active PhC waveguide (Fig. 1c, a=380 nm). Gain spectra for two other PhC lattice constants and the same electronic density of states and carrier distributions are also shown. The gain spectra may be compared with that of a rectangular waveguide (nanowire) embedded in air, which is proportional to the material gain spectrum and has a confinement factor similar to the PhC structures (~40%, see Supplementary Fig. 1 for additional detail). In Fig. 1d, the gain enhancement factor is shown as a function of the group index. The enhancement factor is defined as the modal net gain of the PhC waveguide divided by the modal gain of the nanowire waveguide, (Γg0ng/nb−α)/(Γrefg0), where Γref is the confinement factor of the reference waveguide and α is the loss of the PhC waveguide (see Supplementary Methods). Notice that this provides a conservative estimate of the gain enhancement, as losses in the reference waveguide are neglected. The dashed line in Fig. 1d indicates the linear scaling with group index that is obtained when the impact of structure disorder is neglected. For the regime of large group index (approximated by ng>40, shaded grey), disorder limits the maximum gain enhancement factor that can be reached. Close to the transparency wavelength around 1,500 nm, where the net gain is zero, additional waveguide loss in the PhC waveguide slightly shifts the transparency wavelength for the net gain. As the group index at the transparency point is larger for the structures with larger lattice constant, the gain enhancement in this spectral region is smaller for those structures.
It is well known that as the band edge is approached, scattering losses are enhanced due to slow-light propagation28,29,30,31. This loss enhancement was included phenomenologically using a third-order polynomial dependency on ng. We note that, typically, a second-order polynomial is assumed where the squared term accounts for the backscattering losses and the linear term accounts for out-of-plane losses. However, as noted in refs 28, 29, 30, 31, for passive photonic crystal waveguides (PCW) this is a crude model, as it does not account for the mode shape being dependent on ng. The assumed third-order dependency may partially account for this mode-shape dependency. Throughout the remainder of this work, we shall refer to the modal gain minus waveguide losses as the net gain, g. These results thus predict that the net gain can be enhanced and controlled via the photonic environment rather than the usual approach of modifying the epitaxial structure.
Measurement of slow-light-controlled gain spectra
PhC waveguides with one missing air hole (W1 type) are fabricated in a 340-nm-thick air-embedded InGaAsP membrane with a triangular-lattice pattern of air holes (see Methods). The waveguide is terminated by tapers32 to suppress residual reflections and improve coupling. Similar passive structures have been used for investigating slow-light propagation3,4 and nonlinearities7,8, but in our case an active material is incorporated inside the membrane and the structures are designed such that the slow-light regime spectrally overlaps with the region where positive net material gain can be achieved by optical pumping. A schematic of the setup as well as scanning electron microscopy pictures of fabricated samples are shown in Fig. 2. Figure 3 shows measured spontaneous emission spectra for three 1-mm-long waveguides with different PhC lattice parameters, corresponding to a progressive wavelength shift of the slow-light region by 20 nm.
The devices have identical ten quantum-well (QW) epitaxial structures and the measurements thus clearly show that the emission spectrum can be controlled via the PhC lattice parameters. The different spectra shown for each of the samples correspond to different excitation stripe lengths, defined by blocking part of the pump light in close vicinity to the sample. If the modal gain exceeds the total losses, the spontaneous emission is amplified along the waveguide. To measure the net gain, including propagation losses due to non-resonant residual absorption as well as disorder-induced scattering, we use a standard method originally introduced in the seminal work of Shaklee et al.33 The output intensity may be written as
where l is the excitation stripe length and A is proportional to the local rate of spontaneous emission. To measure the gain, we fitted the data using the normalized function I(l)/I(L), which is independent of A, where L is a reference length given by the longest length included in the fit. Inserts in Fig. 3 show example variations of intensity with stripe length, with the intensity increasing by more than three orders of magnitude, and the corresponding fits. For long stripe lengths, the intensity saturates, the origin of which is discussed later, and this part is omitted in the fit (see Methods for details). Figure 3 shows the extracted gain spectra for the three waveguides under similar pumping conditions. The spectra are seen to shift in good qualitative agreement with the simulations shown in Fig. 1c. Our measurement scheme avoids the problem of Fabry–Perot resonances induced by facet reflections, as the far-side facet is preceded by unpumped material with strong absorption. The caveat is that due to the absence of a well-defined cavity, we do not have access to independent measurements of the absolute group index variation of the structures.
To confirm that our waveguides do display the generally accepted variation of group index with wavelength28,29,31, we present in Fig. 4 the measured emission spectrum of a structure with a=380 nm and r/a=0.25 (same as the waveguide plotted in red in Fig. 3) but implementing a 10-μm-long PhC cavity by terminating the waveguide at both ends by holes. A tenfold light slow down is observed close to the band edge of this device. The slight shift in band edge position, compared with the samples in Fig. 3, is related to the lower relative permittivity of this waveguide, which contains one layer of quantum dots instead of ten QWs. To get information on the location of the band edge for the exact same samples as investigated in Fig. 3, we analyse the fringe spacing, δλ, in the spectra, most clearly noticed for the sample with a=380 nm close to the band edge. We attribute these fringes to imperfections in the lattice that cause reflections. We may calculate the variation of the optical path length as ngL=λ2/(2δλ). To estimate the absolute value of the group index, we compare with the measured group index of the reference QD sample in Fig. 4. Assuming the wavelength dependence of the group index to be the same for the reference sample and the samples used in the gain spectra measurements, which is reasonable considering that they are nearly identical except for absolute shifts of the band edge, we calibrate the group indices for the shortest wavelengths, ng(λ<), to be 6.5, 9 and 11, for the three structures. Using this, we may estimate the group indices as ng(λ)L/[ng(λ<)L]·ng(λ<), giving a maximum ng of 40–50, see Fig. 4a, corresponding to slow-down factors of 11–14. The position of the band edge extracted from these measurements correlate well with the position at which the measured gain spectra attain their maxima, cf. Fig. 3, thus confirming that the gain enhancement is a slow-light effect. Moreover, the magnitudes of the calculated group indices near the band gap are in good agreement with the measured group index of the terminated waveguide structure in Fig. 4 (bottom). Comparing the estimated slow-down factor with the calculated gain enhancement in Fig. 1d, we notice that the latter is slightly smaller, as is expected from the slow-down enhancement of the propagation losses. We have also performed transmission measurements (see Supplementary Fig. 4) confirming that the maximum transmission varies according to the PhC band edge.
As mentioned, the output intensity is observed to saturate beyond a certain length, Lmax, (see Methods). Figure 5a shows the variation of Lmax as a function of measured net gain. The maximum stripe length is observed to decrease with increasing gain, and for large gain values Lmax is seen to scale inversely with gain. By plotting the gain-length product, gLmax, versus net gain (Fig. 5b), we find that gLmax saturates at a value of 8–9, corresponding to a maximum gain of 35–39 dB. This is in good qualitative agreement with findings for bulk amplifiers34, where a maximum gain of about 34 dB, limited by amplified spontaneous emission, was found. We also notice that for a given structure, the product gLmax decreases for small gain values. This is consistent with the attribution of gain saturation to amplified spontaneous emission (ASE). The depletion of the carrier density thus lowers the Fermi levels for conduction and valence bands, and the gain therefore decreases more readily at shorter wavelengths than at longer wavelengths, where the occupation probabilities are close to 1. We take these observations as strong indications that the saturation of the intensity with stripe length is due to carrier depletion and subsequent gain reduction due to amplified spontaneous emission. Notice that the carrier density may also be reduced due to lasing in random cavities formed due to unintentional structural disorder, as discussed later. The prospect of slow-light amplifiers is thus not to increase the absolute gain, but rather to provide high gain in a short device, as required for photonic integration.
In the presence of disorder, multiple scattering events may dominate the propagation of light for long stripe lengths, thus invalidating the Beer–Lambert expression on which equation (2) is based (see ref. 31). Although, in our case, amplified spontaneous emission appears to be the governing cause of saturation, the role of disorder could be experimentally investigated by introducing deliberate, random disorder in the PhC structures.
With present technology, passive PhC waveguides exhibit a propagation loss of ~2 dB mm−1 in the conventional ‘fast-light’ region, while propagation losses strongly depend on ng in the slow-light regime28. Even though the propagation loss therefore is much higher than for well-designed ridge waveguides, a positive net gain coefficient up to ~700 cm−1 is measured (Fig. 3). Gain spectra of electrically contacted standard ridge waveguides, with five QWs of the same composition and thickness as employed here were measured to have a maximum gain of 10 cm−1 per QW, thus revealing a gain enhancement of roughly 700/(10 × 10)=7. Here, a factor ~2 is expected from the tighter confinement of the waveguide (see Supplementary Methods) and the remaining factor ~3.5 can thus be ascribed to slow-light enhancement. From Fig. 4, a slow-light enhancement factor of ~8 at the measured group index of ~50 is expected, when comparing with a reference waveguide of nearly the same confinement factor as the PhC waveguide. The lower experimental enhancement factor is most likely to be due to additional heating and higher carrier loss due to surface recombination in the PhC waveguide structures as well as multiple-scattering effects due to fabrication disorder. However, recent work has demonstrated the feasibility of realizing a buried heterostructure and electrical pumping35, which will strongly reduce these limitations. Furthermore, dispersion engineering4 may be applied to optimize the group index variation relative to the gain peak.
From the gain spectra in Fig. 3, one notices that the transparency point (where the net gain is zero) appears blue shifted for the smallest PhC lattice periodicity. This indicates that the resulting carrier density is higher for that structure despite the near-identical pumping conditions and is likely to be due to suppression of spontaneous emission at longer wavelengths caused by the photonic bandgap. This suggests a way of increasing the quantum injection efficiency into the desired levels without changing the electronic level structure and would be very interesting from a pump efficiency point of view. So far, such tailoring was accomplished by exploiting quantum confinement effects in low-dimensional semiconductors. Further investigations with improved measurement accuracy and implementation of electrical pumping are, however, required to conclude on this, and three-dimensional PhC structures are desirable for exercising complete suppression of undesired recombination channels.
Similar to conventional semiconductor optical amplifiers, the gain of a PhC amplifier will be limited by carrier depletion caused by the injected signal or by amplified spontaneous emission. Slow-light propagation may cause additional effects. As already mentioned, random scattering due to fabrication-induced disorder reduces the maximum attainable group index and increases the loss. As the band edge is approached, local cavities may even form, leading to random lasing36. Even in the absence of disorder, distributed feedback (band edge) lasing22 may set in close to the Brillouin zone edge and these lasing effects will lead to further carrier depletion, thus limiting the maximum gain. It was recently predicted that the slow down of the light itself will be limited by the presence of gain, due to broadening of the optical density of states37. This effect, not yet experimentally observed, may also be contributing to the gain saturation that we observe experimentally, but we cannot presently separate that from the effect of gain depletion due to amplified spontaneous emission.
In conclusion, we have demonstrated that the gain of a waveguide can be enhanced and spectrally controlled by exploiting slow-light propagation. This is promising for the realization of compact integrated PhC amplifiers, which are essential, presently missing, components for integrated photonic chips. The use of slow light may also reduce the power consumption of amplifiers, as less active material needs to be inverted to achieve a given gain. Furthermore, the control of the gain profile via the photonic structure, rather than the electronic, epitaxial structure, provides new design freedom, for example, allowing varying the gain coefficient along the waveguide, which may be exploited for ultrafast low-power signal processing applications. The present work also demonstrates a platform for fundamental studies of propagation and random scattering effects in structures under the combined effect of slow light and net gain, which are topics that have proved very rich, even for passive structures.
The wafers were grown by metal-organic vapour phase epitaxy on InP substrates. The membrane is InGaAsP (λg=1.15 μm) with a total thickness of 340 nm containing one or ten strain-compensated QWs (6 nm In0.75Ga0.25As0.86P0.14 well, 7.2 nm In0.49Ga0.51As0.86P0.14 barrier) in the centre. Sacrificial layers underneath were formed by a stack of 100 nm InP, 100 nm InAlAs and 800 nm InP with a total thickness of 1 μm. A 200-nm layer of SiNx was deposited by plasma-enhanced chemical vapor deposition (PECVD) followed by a 500-nm-thick layer of a positive e-beam resist (zep520A). The patterning was done using e-beam writing by a JEOL-JBX9300FS. The pattern was transferred to the SiNx by CHF3/O2 reactive ion etch and further transferred to the semiconductor by cyclic CH4/H2—O2 reactive ion etch after resist removal. Beneath the active slab, there is a 1 μm-thick sacrificial layer, which is etched away using 1HCl:2H2O selective wet-etching to obtain an air-slab structure.
The devices are optically excited along a stripe by focusing pump laser light onto the waveguide using a cylindrical lens. To avoid effects of heating, the samples are pumped with pulses from a mode-locked Ti:Sapphire laser (wavelength 800 nm, duration ~1 ps, repetition rate 270 kHz) with an average power of 6 mW (corresponding to 40 W cm−2 average power or a pulse fluence of ~1.5 pJ μm−2). The stripe width was ~15 μm. The waveguide output is coupled to a lensed fibre using a PhC waveguide taper. A series of spontaneous emission spectra from well-defined excitation stripe lengths are acquired using a cooled InGaAs array detector on a spectrograph. The excitation stripe lengths are measured from calibrated camera microscope images of the spontaneously emitted near infrared light scattered out from the top of the waveguide.
Gain extraction and error bar estimation
The gain spectrum was extracted by fitting to equation (2) using the maximum likelihood method. Shot noise was found to be negligible and the noise rather resulted from fluctuations due to waveguide–fibre coupling. Accordingly, as the statistical error is proportional to the mean output signal, we assume a log-normal (rather than a normal) distribution corresponding to the logarithm of the output signal being normally distributed. The fits thus minimize the sum of squared residuals for the logarithm of the measured ASE. The error bars shown are the calculated 95% confidence intervals. It might be expected that the uncertainty should be at a minimum where the ASE spectrum peaks, as here the output signal shows the largest variation with stripe length. However, the signal is observed to saturate at a shorter stripe length for higher gain, limiting the useful fitting range where the exponential dependence in equation (2), which neglects saturation, holds true. Examples of fits with indication of the fitting range employed are shown in the insets of Fig. 3. To systematically determine the fitting range, we carried out fits for all wavelengths versus maximum pump lengths and used the set of wavelengths and fitting ranges resulting in an R2 value (coefficient of determination), closest to 1. R2 is a standard measure for the goodness of a fit and was evaluated as R2=1−Serr/Stot, where Serr=∑i[ln (yi)−ln (Ii)]2 and Stot=∑i[ln (yi)− <ln (y)>]2 and yi (Ii) is the measured ASE with pump stripe length zi.
How to cite this article: Ek, S. et al. Slow-light-enhanced gain in active photonic crystal waveguides. Nat. Commun. 5:5039 doi: 10.1038/ncomms6039 (2014).
Hau, L., Harris, S., Dutton, Z. & Behroozi, C. Light speed reduction to 17 metres per second in an ultracold atomic gas. Nature 397, 594–598 (1999).
Bigelow, M., Lepeshkin, N. & Boyd, R. Observation of ultraslow light propagation in a ruby crystal at room temperature. Phys. Rev. Lett. 90, 7–10 (2003).
Vlasov, Y. A., O’Boyle, M., Hamann, H. F. & McNab, S. J. Active control of slow light on a chip with photonic crystal waveguides. Nature 438, 65–69 (2005).
Baba, T. Slow light in photonic crystals. Nature Photon. 2, 465–473 (2008).
Thévenaz, L. Slow and fast light in optical fibres. Nature Photon. 2, 474–481 (2008).
Sancho, J. et al. Integrable microwave filter based on a photonic crystal delay line. Nat. Commun. 3, 1075 (2012).
Corcoran, B. et al. Green light emission in silicon through slow-light enhanced third-harmonic generation in photonic-crystal waveguides. Nature Photon. 3, 206–210 (2009).
Colman, P. et al. Temporal solitons and pulse compression in photonic crystal waveguides. Nature Photon. 4, 862–868 (2010).
Lund-Hansen, T., Stobbe, S. & Julsgaard, B. Experimental realization of highly efficient broadband coupling of single quantum dots to a photonic crystal waveguide. Phys. Rev. Lett. 101, 113903 (2008).
Shi, Z., Boyd, R., Gauthier, D. & Dudley, C. Enhancing the spectral sensitivity of interferometers using slow-light media. Opt. Lett. 32, 915–917 (2007).
Capmany, J., Gasulla, I. & Sales, S. Harnessing slow light. Nature Photon. 5, 731–733 (2011).
Dowling, J. & Scalora, M. The photonic band edge laser: a new approach to gain enhancement. J. Appl. Phys. 75, 1896–1899 (1994).
Benisty, H. et al. From modal control to spontaneous emission and gain in photonic crystal waveguides. Photon. Nanostruct. 4, 1–11 (2006).
Mizuta, E., Watanabe, H. & Baba, T. All semiconductor low- photonic crystal waveguide for semiconductor optical amplier. JPN J. App. Phys. 45, 6116–6120 (2006).
Chen, Y. & Mørk, J. Theory of carrier depletion and light amplification in active slow light photonic crystal waveguides. Opt. Express 21, 29392–29400 (2013).
Sakoda, K. Optical Properties of Photonic Crystals Springer-Verlag (2005).
Sapienza, R. et al. Optical amplification enhancement in photonic crystals. Phys. Rev. A 83, 023801 (2011).
Schwoob, E. et al. Enhanced gain measurement at mode singularities in InP-based photonic crystal waveguides. Opt. Express 12, 1569–1574 (2004).
Viasnoff-Schwoob, E. et al. Spontaneous emission enhancement of quantum dots in a photonic crystal wire. Phys. Rev. Lett. 95, 183901 (2005).
Kuroda, K., Sawada, T., Kuroda, T., Watanabe, K. & Sakoda, K. Doubly enhanced spontaneous emission due to increased photon density of states at photonic band edge frequencies. Opt. Express 17, 13168–13177 (2009).
Kiyota, K., Kise, T., Yokouchi, N., Ide, T. & Baba, T. Various low group velocity effects in photonic crystal line defect waveguides and their demonstration by laser oscillation. Appl. Phys. Lett. 88, 201904 (2006).
Sugitatsu, A. & Noda, S. Room temperature operation of 2D photonic crystal slab defect-waveguide laser with optical pump. Electron. Lett. 39, 213–215 (2003).
Happ, T. D., Kamp, M., Forchel, A., Gentner, J. -L. & Goldstein, L. Two-dimensional photonic crystal coupled-defect laser diode. Appl. Phys. Lett. 82, 4–6 (2003).
Dicaire, I., De Rossi, A., Combrié, S. & Thévenaz, L. Probing molecular absorption under slow-light propagation using a photonic crystal waveguide. Opt. Lett. 37, 4934–4936 (2012).
Mortensen, N. A. & Xiao, S. Slow-light enhancement of Beer-Lambert-Bouguer absorption. Appl. Phys. Lett. 90, 141108 (2007).
Mørk, J. & Nielsen, T. R. On the use of slow light for enhancing waveguide properties. Opt. Lett. 35, 2834–2836 (2010).
Chin, S., Dicaire, I., Beugnot, J. C., Mafang, S. F., Herraez, M. G. & Thévenaz, L. Material slow light does not enhance Beer-Lambert absorption. (OSA OSA/IPNRA/NLO/SL Conference, Washington DC, USA), paper SMA3 (2009).
Le Thomas, N. et al. Light transport regimes in slow light photonic crystal waveguides. Phys. Rev. B 80, 125332 (2009).
O’Faolain, L. et al. Loss engineered slow light waveguides. Opt. Express 18, 27627–27638 (2010).
Mazoyer, S., Hugonin, J. & Lalanne, P. Disorder-induced multiple scattering in photonic-crystal waveguides. Phys. Rev. Lett. 103, 063903 (2009).
Patterson, M. et al. Disorder-induced incoherent scattering losses in photonic crystal waveguides: Bloch mode reshaping, multiple scattering, and breakdown of the Beer-Lambert law. Phys. Rev. B. 80, 195305 (2009).
Tran, Q. V., Combrie´, S., Colman, P. & De Rossi, A. Photonic crystal membrane waveguides with low insertion losses. Appl. Phys. Lett. 95, 061105 (2009).
Shaklee, K. L. & Leheny, R. F. Direct determination of optical gain in semiconductor crystals. Appl. Phys. Lett. 18, 475–477 (1971).
Liu, T., Obermann, K. & Petermann, K. Effect of saturation caused by amplified spontaneous emission on semiconductor optical amplifier performance. Electron. Lett. 33, 2042–2043 (1997).
Matsuo, S. et al. High-speed ultracompact buried heterostructure photonic-crystal laser with 13 fJ of energy consumed per bit transmitted. Nature Photon. 4, 648–654 (2010).
Liu, J. et al. Random nanolasing in the Anderson localized regime. Nat. Nanotechnol. 9, 285–289 (2014).
Grgić, J. et al. Fundamental limitations to gain enhancement in periodic media and waveguides. Phys. Rev. Lett. 108, 183903 (2012).
We thank M. Schubert, University of Konstanz, for developing the PhC membrane process, W. Xue, Technical University of Denmark, for performing the measurement of the spectrum reported in Fig. 4, and A. de Rossi and S. Combrié for help with the taper technology. Villum Fonden is acknowledged for financial support via the NATEC Centre of Excellence.
The authors declare no competing financial interests.
Supplementary Methods, Supplementary Figures 1-4 and Supplementary References. (PDF 1080 kb)
Rights and permissions
About this article
Cite this article
Ek, S., Lunnemann, P., Chen, Y. et al. Slow-light-enhanced gain in active photonic crystal waveguides. Nat Commun 5, 5039 (2014). https://doi.org/10.1038/ncomms6039
This article is cited by
Structurally engineered colloidal quantum dot phosphor using TiO2 photonic crystal backbone
Light: Science & Applications (2022)
Synthesis, crystal growth and characterization of semi-organic NLO materials: L-valine copper chloride as optoelectronic sensor
Indian Journal of Physics (2022)
Universal lasing condition
Scientific Reports (2021)
Enhanced light–matter interaction in a hybrid photonic–plasmonic cavity
Applied Physics A (2021)
Slow waves in locally resonant metamaterials line defect waveguides
Scientific Reports (2017)
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.