Chiral discrimination of vapours plays an important role in olfactory perception of biological systems and its realization by artificial sensors has been an intriguing challenge. Here, we report a simple method that tangibly visualizes the chirality of a diverse variety of molecules dissolved from vapours with high sensitivity, by making use of a structural change in a periodic microstructure of a nematic liquid crystal confined in open microchannels. This microstructure is accompanied by a topological line defect of a zigzag form with equal lengths of ‘zig’ and ‘zag.’ We find that a tiny amount of vapour of chiral molecules injected onto the liquid crystal induces the imbalance of ‘zig’ and ‘zag’ depending on its enantiomeric excess within a few seconds. Our liquid-crystal-based ‘chirality balance’ offers a simple, quick and versatile chirality-sensing/-screening method for gas-phase analysis (for example, for odours, environmental chemicals or drugs).
Chiral discrimination of vapours plays an important role in olfactory perception of biological systems1,2. It has been an intriguing challenge to mimic such systems for the realization of artificial analogues such as odour sensors3,4 for specific drug analysis and environmental monitoring. Many of the artificial gas sensors for chiral discrimination so far crucially rely on selective interactions between an analyte enantiomer and a complementary chiral environment. Construction of the latter, however, requires complex and ad-hoc molecular designs and syntheses, and therefore only molecules of specific architecture can be distinguished by these sensors.
A nematic liquid crystal (NLC) is a fluid phase formed by anisotropic molecules that are preferentially aligned along a common axis n called the director5. It is well known that the sensitivity of the optical properties of NLCs to external stimuli has been effectively and ingeniously made use of in liquid crystal (LC) displays (here, the ‘external stimulus’ is an applied electric field), and NLCs have been an attractive candidate for chemical sensing as well. It is because they can exhibit optically-detectable changes in their macroscopic alignment when, for example, doped with chiral molecules6,7,8,9,10,11 or analytes modify the surfaces of NLCs12,13. However, chiral sensing, especially of vapours, using NLCs has been a challenge because volatile small chiral molecules dissolved from a vapour phase can generally induce only a small change in the NLC alignment, which is difficult to detect. Although it was demonstrated half a century ago by Fergason14 that the utility of a chiral NLC for sensing vapour molecules because the pitch of its helical alignment and the resulting structural colour are highly sensitive to the dissolution of vapour molecules, this mechanism cannot be used for chirality sensing, because the helical pitch varies irrespective of whether the absorbed molecules are chiral or not. Another reason why direct detection of the chirality of vapour samples using LC technology has not been achieved yet is that NLCs used for chirality detection are in most cases bounded by solid (or liquid) interfaces, which makes efficient dissolution of chiral molecules from their vapour phases practically impossible (a typical example is a Grandjean–Cano wedge cell6). Still, self-organized non-trivial structures of a NLC confined in specific geometry15,16,17,18,19,20,21,22,23,24,25,26,27,28 could enhance its response to a weak external stimulus so that the response could be manifest as the structural change directly observable using an optical microscope. Indeed, it has been reported that the curvature of a topological line defect in a twisted NLC cell is highly sensitive to chiral molecules doped in advance10.
Here, as a possible means to detect the chirality of vapour samples, we consider an achiral NLC confined within an open microgroove29 with frustrated interfacial alignment (anchoring) conditions. A great advantage of our open geometry is that vapour molecules readily dissolve into the NLC through the NLC/air interface, which is appropriate for efficient chirality detection. The NLC exhibits a topological line defect of the orientational order (a line disclination) of zigzag form26,27,28 in the bulk (Fig. 1a). The formation of a line disclination is a manifestation of the frustrated anchoring conditions that do not allow a continuous orientation profile without singularities. The winding number5 of the line disclination is +1/2, compatible with the anchoring conditions, and the curvature of the groove surface28. This zigzag line disclination is accompanied by self-organized periodic domains with alternating twist distortions along the vertical direction. In our previous work26, we showed that the twist distortions responsible for the formation of the zigzag line disclination is attributable to the smallness of the elastic constant K22 for twist distortions compared with other elastic constants. The boundaries between domains with different twist directions involve a kink of the line disclination, as depicted schematically in Fig. 1a. Note that singularities of the orientational order in the NLC exist only at the line disclination; the kinks of the line disclination are not accompanied by any sheet-like singularities5. The length of a domain with right-handed twist distortion, lR, and that of a domain with left-handed twist distortion, lL, are equal because the free energy densities of both domains are the same (here the lengths are measured along the microgroove direction). This symmetry is attributed to the symmetry of the twist elastic energy, ft, with respect to the sign of the wavenumber of the twist distortion q; ft=½K22(q−q0)2, with q0 being zero for achiral NLCs5.
In general, the dissolution of chiral molecules into a NLC has the effect of transferring the molecular chirality to the macroscopic twisted/helical distortions of the director5,6,7,8,9,10,11. The presence of spontaneous twist distortions amounts to nonzero q0 in ft. Let c± denote the concentrations of (±)-enantiomers of a chiral molecule (the index indicates the sign of the predefined optical rotation), and q0 is then written as q0=β+c++β−c−=β(c+−c−). Here, chiral symmetry dictates that β+=−β−≡ β. β is the twisting power, and its sign is defined such that β>0 when a (+)-enantiomer induces right-handed twist. Nonzero q0 breaks the symmetry of ft with respect to q, and it is expected that, in our system with zigzag disclination lines, this asymmetry will manifest itself as unequal lR and lL, whose detection requires only a conventional polarized optical microscope (POM).
Our experiments presented below clearly demonstrate that the dissolution of chiral molecules indeed brings about the structural change of a zigzag disclination line mentioned above, which is accounted for in a more quantitative manner by a simple theoretical model. The response is rapid enough because of the vapour dissolution/vaporization kinetics discussed below. The rapidness as well as high sensitivity of the response together with the simplicity of the setup makes our system useful as a simple method that tangibly visualizes the chirality of a diverse variety of vapour molecules.
Responses of zigzag defects to a chiral vapour
The setup of our experiments to substantiate the symmetry breaking of a zigzag disclination by chirality is sketched in Fig. 1. The width w and the maximum thickness d of the NLC in the microgrooves are 12±1 μm and 1.8±0.2 μm, respectively. An analyte vapour is injected from a tube nozzle fixed near the surface of the NLC at a constant flow rate r, and the NLC surface is exposed to the steady flow for ~4 s for dissolution (see Methods). Without injection, the system is in contact with ambient air of relative humidity of ~50% at room temperature. The relative vapour concentration is cr=cv/c0, where c0 is the concentration at the equilibrium vapour pressure at room temperature. The vapour injection tests were repeated with an interval of at least 10 min with an air flow for vaporization of the dissolved molecules. The sensor response is constantly monitored by the POM image with crossed polarizers. A sensitive tint plate is also used so that domains with left-handed twist are coloured in blue. Examples of microscope images with balanced and imbalanced zigzag domains, together with schematic illustrations of the orientational order, are shown in Fig. 1b,c.
To characterize the resulting imbalance in the zigzag domain lengths, we introduce the enatiomeric excess of zigzag domains, that is, eez ≡ (lR−lL)/(lR+lL). In Fig. 2, we show time-dependent raw responses of eez for saturated vapour mixtures (cr=1) of (±)-limonene with different enantiomeric excesses of vapour, ee, defined by ee ≡ (c+−c−)/(c++c−). In most cases, |eez| initially exhibits a rapid increase with time t and almost saturated in 4 s of exposure. After the cessation of vapour injection, |eez| decays rapidly with a characteristic time similar to that of the dissolution process, indicating the vaporization of dissolved molecules.
Now let us estimate the characteristic time τ of relaxation of the director orientation that is given by τ ~η0d2/K (for example, ref. 5), with d, η0 and K being the characteristic length, the effective viscosity and the typical elastic constant, respectively. With d~1 μm (thickness of the NLC filament), η0~10−3 Pa s and K~10−11 N, τ is estimated as ~10−3 s. This is much shorter than the timescale of the observed response, a few seconds; the director reorientation well follows the concentration change of the chiral dopant within the experimental timescale of interest. Even when the length of ‘zig’ or ‘zag’ part (10 μm at most from Fig. 1) is taken as d, the estimated τ ~ 10−1 s is still smaller than a few seconds. Therefore, the relaxation of the orientational order (and hence the defects) plays essentially no role in the determination of the characteristic response time and the observed response directly reflects the concentration change governed by the dissolution/evaporation kinetics through the air-NLC interface (Supplementary Discussion).
The observed response shown in Fig. 2 also suggests that the vapour dissolution/vaporization kinetics is a first-order process (Supplementary Discussion). As, in our very thin NLC, the characteristic time should be proportional to d, the quick response of a few seconds owes to the present small spatial scale of the LC confined within microgrooves. A change in |eez| of ~0.2 in such a timescale is readily detected by observing which twisted domains elongate or shrink (Supplementary Movie 1). Additional experiments (Supplementary Fig. 1) indicate that our method enables the detection of induced helical pitch (∝q0) as large as 0.1~1 mm, demonstrating high sensitivity to a chirality-induced structural change.
Responses to various chiral vapours
The sign of β is material dependent, and the present results indicate β<0 for (+)-limonene-rich analytes because they elongate left-handed twist domains. This information is important for the identification of the chirality of analytes, that is, the absolute stereochemical configuration, and is most easily obtained by the present method. Table 1 shows the results for various chiral vapours including major aroma constituents, demonstrating the versatility of the present method. As references, we have also confirmed that achiral vapours, for example, p-menthane and vanillin, yield no detectable change in eez.
The amount of analyte vapours necessary for chiral detection is significantly small owing to the quick response; only a volume of ~0.26 ml was injected within 4 s for each curve shown in Fig. 2. In addition, the quick vaporization also reduces the waiting time for the next test, which is accelerated further by exposure of the NLC to air flow.
The values of eez after 4 s exposure are plotted against ee in inset in Fig. 2. Again this confirms that β<0 for (+)-limonene because d(eez)/d(ee)<0. Point symmetry of the plots with respect to the origin indicates that the present system directly detects the imbalance and the sign of the chirality, and only the knowledge of the sign of β (Table 1) is required as perquisite to discriminate enantiomers. This mechanism is entirely different from that of other conventional chiral sensing3,4 and analytical methods, such as chiral chromatography techniques30, which require the complementary chiral environments for respective enantiomers. The effect of the flow rate r on the responses of eez is also clearly shown; the sensitivity of eez to ee increases with r owing to the enhanced dissolution. By exploiting the plots in inset in Fig. 2 as calibration curves, we can quantify ee of a vapour sample containing (±)-enantiomers of a single species from the observed response at fixed time t, cv and r.
Additional experiments (Fig. 3) demonstrate the ability to quantify cr for different enantiopure chiral compounds, that is, |ee|≈1. The plots of |eez| at t=4 s and r=0.33 ml s−1 with respect to cr also show sublinear dependence with respect to cr and the saturation of |eez|→1 at higher concentrations. These plots can be exploited as calibration curves for the determination of the vapour concentration of the pure enantiomer. The chiral material-dependent curves indicate the difference in the sensitivity; β pinene>limonene>carvone>terpinen-4-ol>menthol. The sensitivity depends on various material-dependent unknown parameters, such as those for dissolution/vaporization kinetics and β, and is difficult to estimate in advance. Nevertheless, once the curves are acquired, the difference would be a useful clue to estimate the major compound especially for a mixture of chiral compounds. Accordingly, the detection limit is also material dependent; for example, the minimum detectable value of cr for carvone is approximately 0.01 corresponding to ~5 p.p.m. This is comparable to or better than that of the previously reported method based on a field effect transistor4.
As examples of a simple analysis of natural vapour mixtures, we determined the signs of eez for the headspace gases taken from vials containing torn orange (Citrus unshiu) peels, torn spearmint (Mentha spicata) leaves and torn immature conifer cone of a Japanese red pine (Pinus densiflora) to be (−), (+) and (+), respectively. If we assume that the major volatile compounds for the orange peel is limonene, that for the spearmint is carvone and those for the pine conifer cone are α/β-pinenes31, the signs of their optical rotations are reasonably estimated from the obtained signs of β for (+)-enantiomers (Table 1); (+)-limonene, (−)-carvone and (−)-α/β-pinenes.
Finally, we discuss the behaviour of lR and lL in response to nonzero q0. We begin with our previous model accounting for the occurrence of a zigzag disclination in an achiral NLC26, and extend it to include the effect of chirality. Refer to Methods for details of the theoretical argument. We find that |eez| increases sublinearly with the increase of |q0| until it reaches 1, in qualitative agreement with our experimental results (Fig. 3). Moreover, the experimental curves fall well onto a single theoretical curve after appropriate rescaling of c (Inset of Fig. 3). Though admittedly crude, our theoretical model accounts for our experimental findings remarkably well. The presence of a master curve shown in the inset of Fig. 3 clearly demonstrates the universality of the chirality-induced symmetry breaking of the zigzag defect, which could be used as a standard for a diverse variety of chiral vapours such as essential oils, aroma constituents and phytoncides.
To conclude, we have shown for the first time that it is possible to detect the existence of chirality in vapour samples with high sensitivity, by making use of a structural change in a periodic microstructure of an achiral NLC confined in open microchannels. Although it is already known that the pitch of a cholesteric LC, and thus its colour, change according to the sign of the chirality of dissolved chiral molecules5, the variation of the pitch cannot be applied to the determination of the existence of chirality because the pitch can vary sensitively in response to the dissolution of achiral14 as well as chiral molecules. Therefore, we stress the advantage of our method over the previous ones based on LCs in that the distinction between chiral and achiral molecules is possible. In addition, our system works at ambient temperature and pressure, and its setup is highly simple and not at all demanding; sinusoidal microgrooves, an achiral NLC of volume less than 1 pl, and an ordinary POM. Moreover, it requires only a few ml of collected or prepared gas-phase analyte for chiral sensing and no condensation, extraction or predissolution into a solvent is necessary. Our zigzag disclination line that responds to the presence of chirality with clear structural changes could be dubbed ‘a chirality balance,’ and offers a simple, quick and economical chirality-sensing method, especially suitable for vapour samples, facilitating the construction of a portable and user-friendly chiral sensor. In addition, our method as an optional chiral-screening technique could complement conventional gas-phase analyses such as gas chromatography30.
Preparation of zigzag defects in a NLC
Microwrinkles with aligned microgrooves filled with a NLC that shows a zigzag defect structure were prepared according to the identical protocols reported in ref. 26. The microwrinkles were self-organized on the top surface of a polyimide-capped polydimethylsiloxane substrate (12 × 12 × 6 mm3). The wavelength of the groove λ was 14.5 μm. The aspect ratio of the microwrinkles was almost constant, 0.13±0.01.
The microgrooves were filled with room temperature NLCs, by spreading a droplet of the NLC placed on the microgrooved surface. With the present aspect ratio, pentylcyanobiphenyl (Sigma-Aldrich) or ZLI-1132 (MERCK) was stabilized within the microgrooves via capillary effect29. The air/liquid and wrinkle/liquid interfaces impose normal anchoring and unidirectional planar anchoring, respectively. The local easy axis of the latter is perpendicular to the groove direction and along tangential direction of the sinusoidal curve on the plane. These antagonistic anchoring conditions lead to frustrated alignment with a wedge disclination line of topological charge +1/2, which spontaneously shows zigzags. The LC alignment was observed using a transmitted polarized microscope (BX-51P, Olympus). To differentiate small optical rotations visually by the colour difference, a 530 nm sensitive tint plate (1λ, U-TP530, Olympus) was used as a test plate compensator under crossed-Nicol conditions.
Preparation of analyte vapours
We prepared a vial (40 ml) with a rubber septum containing 1–5 g of a volatile liquid or solid compound with chirality. The headspace was equilibrated at least for 15 min with rotating magnetic stirrer before sampling. For limonene, 11 mixtures with ee from −1 to +1 with the intervals of 0.2 were prepared by mixing the enantiopure enantiomers, (±)-limonene (Sigma-Aldrich). To prepare diluted vapours, the saturated one was mixed with air with vigorous stirring. Enantiopure compounds used in this study are 2,3-butanediol, 1-phenylethanol, α-pinene, 3-carene, carvone, carveol, menthone, limonene, borneol, linalool, β-citronellol, trans-caryophyllene, 2-butanol, camphene, α-thujone, fenchone, rose oxide, menthol, menthyl chrolide, menthyl acetate and α-bisabolol (Sigma-Aldrich), and terpinen-4-ol (TCI), and 1-phenylethylamine, β-pinene, δ-decanolactone, α-terpineol and ibuprofen (WAKO chemical). Achiral compounds, p-menthane and vanillin (Sigma-Aldrich) were also used as analyte vapour compounds to confirm that the present LC-based chirality sensor show no response to them. Three natural plant-based chiral vapour mixture samples were prepared as follows. The peels of a fresh orange (Citrus unshiu), fresh spearmint (Mentha spicata) leaves and fresh yellow-greenish immature conifer cone of a Japanese red pine (Pinus densiflora) were torn and approximately 2 g of each was put into an individual vial with rubber septa. The vapour mixtures were sampled for tests from the headspace after a 10-min equilibration.
The nozzle of a Teflon tube with an inner diameter of 0.5 mm was fixed above the LC surface. The flow axis was inclined and made an angle of 14° with the surface. The flow rate r was controlled by the injector between 0.033 and 0.33 ml s−1. Soon after 4 ml of an analyte vapour was sampled into a disposable syringe (5 ml, SS-05LZ, Termo) from the headspace of the sample vial, the syringe was connected to the Teflon tube through the syringe needle. The injection, which was electrically controlled using a stepping motor (SGSP-25ACT-B0, Sigma-Koki), was initiated within 1 min after vapour sampling and it was kept for 4 s. After the cessation of injection, the dissolved molecules could evaporate because the NLC was now exposed to an ambient atmosphere. POM images were monitored and zigzag domains lengths were measured by tracking the domain boundaries from the acquired movies (30 frames/s) by a software analysis (2D-PTV, Digimo). Five pairs of analysed zigzag domain lengths were averaged to calculate eez. The observed position was fixed to an area, which was approximately 1.5 mm apart from the nozzle along the nozzle axis. The NLC with the zigzag defects could be repeatedly used for the sensing by expelling the dissolved volatile molecules after each test by air flow or heat and was stable for at least 6 months in an ambient condition.
To discuss the free energy of the NLC with a zigzag defect, we consider three contributions; (i) the elastic energy of a (straight) disclination line E(Ω), as a function of its angle with respect to the groove direction (Ω), (ii) the energetic penalty of the disclination line approaching the groove wall f1, and (iii) the free energy of defect kinks f2 (in the following, ε, f1 and f2 are the free energies per unit length of the groove).
To evaluate E(Ω), we start with the elastic energy of a disclination line given in equation (1) of ref. 26 for an achiral NLC, that is,
and discuss how Equation (1) is extended to the case of a chiral nematic. Here, φ characterizes the twist distortions below the disclination line, γ is the anchoring strength at the groove surface, κ ≡ (πK/4)ln(R/rc). K is the splay/bend elastic constant (they are assumed to be equal for simplicity), and R and rc are the upper/lower cutoff, respectively, for the evaluation of the elastic energy of the disclination line (See ref. 26. R is determined by the depth of the LC, and rc is the size of the disclination core). The first term, the contribution from the elastic distortions around the disclination line (with microscopic cutoff rc and the outer cutoff R) is not affected by chirality. The second term taking care of the contribution from twist distortions is now modified to (1/2)γ(φ−q0)2, where q0 is the wavenumber of spontaneous twist distortions arising from chirality (defined in the main text), and is the thickness of the region in which twist distortions are relevant (see Fig. 4a of ref. 26, where is denoted by d).
We minimize ε(Ω, φ) with respect to φ numerically, and plot ε(Ω) for various values of q0 in Fig. 4. We observe (i) that ε(Ω)→∞ when Ω→π/2 (which is obvious from Eq. (1)), (ii) that the value of Ω giving the minimum of ε(Ω), which will be denoted by Ω0 hereafter, is insensitive to the variation of q0, (iii) convex form of ε(Ω) around Ω0, and (iv) ε(Ω0)≈−ε(−Ω0). From these observations, we can safely model ε(Ω) by,
which facilitates the following numerical analyses. Here, η is a numerical constant of order unity, and Δ characterizes the strength of chirality. (Δ=0 for an achiral case). With a reasonable choice of αc=0.1, K22/K=0.5, γ/κ=0.2, we have η≈1, Ω0≈0.2. We also note that Δ is almost proportional to q0, and Δ/q0≈−0.17 for the above choice of parameters.
f1 has been already presented in ref. 26 and in the present notation, it reads
where g1(x) ≡ x−1ln[(1+x)/(1−x)], λ is the width of the groove, and D ≡ (l/2) × tanΩ, with l being the length of the projection of a segment of line disclination onto the groove direction. When c1≈1 and K≈κ, c1Kh/(λ/2)=α κ with α≈0.25. In the following, we measure the length in units of λ/2.
As we did in ref. 26, we simply assume that the elastic energy per kink is f2≈κ ld, where ld has the dimension of length and is assumed to be small compared with other relevant characteristic lengths.
The energetics of a disclination line with ‘asymmetric’ zigzag form is now given as follows. The ‘zig’ part is characterized by l=lR and D=DR (and tanΩR=2DR/lR), and the ‘zag’ part by l=lL and D=DL. Then the total energy of a zigzag disclination line per unit length of the groove is given by
Note again that all the lengths are measured in units of λ/2 and DR,L, lR,L and ld are now dimensionless.
We minimize fzigzag with respect to DR,L and lR,L. Note that DR+DL must be zero because otherwise the zigzag disclination will eventually reach the wall of the groove. From our experimental observations, we find that the number of kinks per unit length stays constant except when a first-order transition occurs between a disclination with kinks and a straight one. The constancy of the number of kinks is probably attributed to a large energy barrier for the creation or annihilation of kinks. Therefore, we impose lR+lL=(const.) in addition when we minimize fzigzag. We determine the constant lR+lL by minimizing fzigzag for Δ=0 with the constraint DR+DL=0 and no constraint for lR,L (in this case lR=lL).
In the inset of Fig. 3, we plot eez ≡ (lR–lL)/(lR+lL) as a function of Δ for α=0.25, η=1, Ω0=0.2 and ld=0.04. Δ is appropriately rescaled to compare this theoretical eez to experimental ones. This theoretical argument nicely reproduces some qualitative features of the experimental eez; sublinear dependence of eez on cr(∝ q0) and the saturation of eez to 1 for large cr.
How to cite this article: Ohzono, T. et al. A liquid crystalline chirality balance for vapours. Nat. Commun. 5:3735 doi: 10.1038/ncomms4735 (2014).
Leitereg, T. J., Guadagni, D. G., Harris, J., Mon, T. R. & Teranishi, R. Evidence for the difference between the odours of the optical isomers (+)- and (−)-carvone. Nature 230, 455–456 (1971).
Friedman, L. & Miller, J. G. Odor incongruity and chirality. Science 172, 1044–1046 (1971).
Bodenhöfer, K. et al. Chiral discrimination using piezoelectric and optical gas sensors. Nature 387, 577–580 (1997).
Torsi, L. et al. A sensitivity-enhanced field-effect chiral sensor. Nat. Mater. 7, 412–417 (2008).
de Gennes, P. G. & Prost, J. Physics of Liquid Crystals Clarendon (1993).
Solladié, G. & Zimmerman, R. G. Liquid crystals: a tool for studies on chirality. Angew. Chem. Int. Ed. 23, 348–362 (1984).
Renn, S. R. & Lubensky, T. C. Abrikosov dislocation lattice in a model of the cholesteric–to–smectic-A transition. Phys. Rev. A 38, 2132–2147 (1988).
Kikuchi, H., Yokota, M., Hisakado, Y., Yang, H. & Kajiyama, T. Polymer-stabilized liquid crystal blue phases. Nat. Mater. 1, 64–68 (2002).
Coles, H. J. & Pivnenko, M. N. Liquid crystal ‘blue phases’ with a wide temperature range. Nature 436, 997–1000 (2005).
Raynes, E. P. The use of bowed reverse twist disclination lines for the measurement of long pitch lengths in chiral nematic liquid crystals. Liq. Cryst. 33, 1215–1218 (2006).
Goodby, J. W. et al. Transmission and amplification of information and properties in nanostructured liquid crystals. Angew. Chem. Int. Ed. 47, 2754–2787 (2008).
Gupta, V. K., Skaife, J. J., Dubrovsky, T. B. & L. Abbott, N. L. Optical amplification of ligand-receptor binding using liquid crystals. Science 279, 2077–2080 (1998).
Bai, Y. & Abbott, N. L. Enantiomeric interactions between liquid crystals and organized monolayers of tyrosine-containing dipeptides. J. Am. Chem. Soc. 134, 548–558 (2012).
Fergason, J. L. Liquid crystals. Sci. Amer. 211, 77–85 (1964).
Meyer, R. B. On the existence of even indexed disclinations in nematic liquid crystals. Phil. Mag. 27, 405–424 (1973).
Press, M. J. & Arrott, A. S. Elastic energies and director fields in liquid crystal droplets, I. cylindrical symmetry. J. Phys. Colloques. 36, C1-177–184 (1975).
Lavrentovich, O. D. Topological defects in dispersed words and worlds around liquid crystals, or liquid crystal drops. Liq. Cryst. 16, 117–124 (1998).
Link, D. R., Nakata, M., Takanishi, Y., Ishikawa, K. & Takezoe, H. Patterns in hybrid nematic liquid-crystal films: topography and topology. Phys. Rev. Lett. 87, 195507 (2001).
Kleman, M. & Lavrentovich, O. D. Soft Matter Physics: An Introduction Springer-Verlag (2003).
Oswald, P. & Pieranski, P. Nematic and cholesteric liquid crystals Taylor & Francis: New York, USA, (2005).
Palffy-Muhoray, P., Gartland, E. C. & Kelly, J. R. A new configurational transition in inhomogeneous nematics. Liq. Cryst. 16, 713–718 (1994).
Carbone, G., Lombardo, G., Barberi, R., Musevic, I. & Tkalec, U. Mechanically induced biaxial transition in a nanoconfined nematic liquid crystal with a topological defect. Phys. Rev. Lett. 103, 167801 (2009).
Fernández-Nieves, A. et al. Novel defect structures in nematic liquid crystal shells. Phys. Rev. Lett. 99, 157801 (2007).
Buscaglia, M., Lombardo, G., Cavalli, L., Barberi, R. & Bellini, T. Elastic anisotropy at a glance: the optical signature of disclination lines. Soft Matter 6, 5434–5442 (2010).
Fukuda, J. & Žumer, S. Quasi-two-dimensional Skyrmion lattices in a chiral nematic liquid crystal. Nat. Commun 2, 246 (2011).
Ohzono, T. & Fukuda, J. Zigzag line defects and manipulation of colloids in a nematic liquid crystal in microwrinkle grooves. Nat. Commun. 3, 701 (2012).
Ohzono, T. & Fukuda, J. Transition of frustrated nematic order and fluctuation of topological defects in microwrinkle grooves. Soft Matter 8, 11552–11556 (2012).
Ohzono, T., Fukuda, J., Suzuki, K. & Yamaguchi, T. ±1/2 Wedge disclinations stabilized by a sinusoidal boundary in a thin hybrid nematic liquid-crystal film. Phys. Rev. E Stat. Nonlin. Soft. Matter Phys. 86, 030701(R) (2012).
Ohzono, T., Monobe, H., Shiokawa, K., Fujiwara, M. & Shimizu, Y. Shaping liquid on a micrometre scale using microwrinkles as deformable open channel capillaries. Soft Matter 5, 4658–4664 (2009).
Beesley, T. E. & Scott, R. P. W. Chiral Chromatography John Wiley and Sons (1998).
Parry, E. J. The Chemistry of Essential Oils and Artificial Perfumes Scott, Greenwood and Son (1918).
We would like to thank MERCK for supplying some reagents and M. Ishikawa, H. Sakaue, M. Aoyagi, Y. Norikane, Y. Manaka, H. Kihara, M. Yoshida, M. Yoneya and T. Yamaguchi for useful discussions. T.O. was partially supported by the Japanese Ministry of Education, Culture, Sports, Science and Technology (MEXT) via a Grant-in-Aid for Scientific Research on Innovative Areas (Grant No. 24120003), and J.F. was supported by JSPS Grant-in-Aid (KAKENHI) for Scientific Research (C; Grant No. 25400437). All authors were also supported by a fundamental research fund of AIST for ‘Research Party for Emergent Functions of Anisotropic Media’.
The authors declare no competing financial interests.
Supplementary Figure 1, Supplementary Discussion and Supplementary References (PDF 157 kb)
Sensor responses of zigzag defects in nematic liquid crystals confined within microgrooves of self-organized microwrinkles to a chiral vapour. We present a real-time movie showing optical patterns of zigzag defects upon exposure to a saturated chiral vapour of (+)-carvone at two different flow rates. It can be observed visually that the blue domains, which correspond to those with left-handed twist distortions, elongate and the orange ones shrink in a few second after injection is started. (MOV 3089 kb)
About this article
Cite this article
Ohzono, T., Yamamoto, T. & Fukuda, Ji. A liquid crystalline chirality balance for vapours. Nat Commun 5, 3735 (2014). https://doi.org/10.1038/ncomms4735
Scientific Reports (2016)
Spontaneous emergence of chirality in achiral lyotropic chromonic liquid crystals confined to cylinders
Nature Communications (2015)
Nature Communications (2015)
Nature Physics (2014)