Abstract
Cooling a mechanical resonator mode to a subthermal state has been a longstanding challenge in physics. This pursuit has recently found traction in the field of optomechanics in which a mechanical mode is coupled to an optical cavity. An alternate method is to couple the resonator to a wellcontrolled twolevel system. Here we propose a protocol to dissipatively cool a room temperature mechanical resonator using a nitrogenvacancy centre ensemble. The spin ensemble is coupled to the resonator through its orbitallyaveraged excited state, which has a spin–strain interaction that has not been previously studied. We experimentally demonstrate that the spin–strain coupling in the excited state is 13.5±0.5 times stronger than the ground state spin–strain coupling. We then theoretically show that this interaction, combined with a highdensity spin ensemble, enables the cooling of a mechanical resonator from room temperature to a fraction of its thermal phonon occupancy.
Introduction
Cooling a mechanical resonator to a subthermal phonon occupation can enhance sensing by lowering the resonator’s thermal noise floor and extending a sensor’s linear dynamic range^{1,2,3,4}. Taken to the extreme, cooling a mechanical mode to the ground state of its motion enables the exploration of quantum effects at the mesoscopic scale^{5,6,7}. These goals have motivated researchers in the field of optomechanics to invent methods for cooling mechanical resonators through their interactions with light. Such techniques have been able to achieve cooling to the ground state from cryogenic starting temperatures^{6,7} and to near the ground state from room temperature^{8,9,10,11,12}.
A wellcontrolled quantum system coupled to the motion of a resonator can also be used to cool a mechanical mode^{13,14}. Recently, nitrogenvacancy (NV) centres in diamond have been coupled to mechanical resonators through coherent interactions with lattice strain^{15,16,17,18,19,20,21,22}. The opportunity to use these interactions has stimulated the development of singlecrystal diamond mechanical resonators^{23,24,25,26} and motivated several theoretical proposals for cooling such resonators with a single NV centre^{13,14,27,28}. In principle, replacing the single NV centre with a manyNV ensemble can provide a collective enhancement to the strain coupling, which could increase the cooling power of these protocols. In practice, however, ensembles can shorten spin coherence times and introduce inhomogeneities that may make collective enhancement impractical, depending on the proposed mechanism. To make ensemble coupling a useful resource, it thus becomes crucial to design a cooling protocol that is insensitive to these side effects.
In this work, we study the hybrid quantum system composed of an NV centre spin ensemble collectively coupled to a mechanical resonator with the goal of developing a method for cooling the resonator from ambient temperature. Experimentally, we characterize the previously unstudied spin–strain coupling within the room temperature NV centre excited state (ES), and we find that it is 13.5±0.5 times stronger than the ground state (GS) spin–strain interaction. We then propose a dissipative cooling protocol that uses this ES spin–strain interaction and theoretically show that a dense NV centre ensemble can cool a highQ mechanical resonator from room temperature to a fraction of its thermal phonon population. The proposed protocol requires neither long spin coherence times nor strong spinphonon coupling, and the cooling power scales directly with the NV centre density. These properties make our proposed protocol a practical approach to cooling a room temperature resonator.
Results
NV centre–strain interactions
To achieve substantial cooling from ambient conditions, we require a room temperature NV centre–strain interaction that can be enhanced by an ensemble. We first consider the orbitalstrain coupling that exists within the NV centre ES at cryogenic temperatures. This 850±130 THz per strain interaction offers a promising route towards single NV centremechanical resonator hybrid quantum systems^{21,22}. For ensemble coupling, however, inevitable static strain inhomogeneities will strongly broaden the orbital transition and prohibit collective enhancement. Moreover, the orbital coherence begins to dephase above 10 K because of phonon interactions^{29}, limiting applications of orbitalstrain coupling to cryogenic operation.
A weaker (21.5±1.2 GHz per strain) spin–strain coupling exists at room temperature within the NV centre GS (ref. 17). The resonance condition for this interaction is determined by a static magnetic bias field which can be very uniform across an ensemble. This GS spin–strain interaction thus offers a path towards coupling an ensemble to a mechanical resonator. As the NV centre density grows, however, the GS spin coherence will decrease^{30,31}, limiting the utility of the collective enhancement.
Finally, we consider spin–strain interactions in the room temperature ES, which have not been thoroughly investigated but might provide the desired compatibility with dense ensembles. For temperatures above ∼150 K, orbitalaveraging from the dynamic Jahn–Teller effect erases the orbital degree of freedom from the NV centre ES Hamiltonian, resulting in an effective orbital singlet ES at room temperature^{29,32,33,34}. Previously, magnetic spectroscopy measured an unidentified spin splitting within the room temperature ES that is on the order of 10 times stronger than the GS spin–strain interaction. These measurements hinted that this splitting might be a spin–strain interaction in the ES (refs 35, 36). Like the GS spin–strain coupling, the resonance condition for such an interaction would be determined by a static magnetic bias field, enabling collective enhancement with an ensemble. Furthermore, the NV centre density is not expected to affect the ES coherence time, which is limited by the ES motional narrowing rate^{34,37}. Such an ES spin–strain interaction could thus offer a promising path towards coupling a dense NV centre ensemble to a mechanical resonator. Our first goal then becomes to understand and precisely quantify this coupling.
Assuming this ES coupling is the result of a spin–strain interaction, we can write the spin Hamiltonian for an NV centre in the presence of a magnetic field B and nonaxial strain . Both the GS and room temperature ES Hamiltonians then take the form (ħ=1)^{36,38}
where /2π=1.42 GHz and /2π=2.87 GHz are the ES and GS zerofield splittings, γ_{NV}/2π=2.8 MHz/G is the NV centre gyromagnetic ratio, MHz (ref. 39) and MHz are the ES and GS hyperfine couplings to the ^{14}N nuclear spin, S (I) is the electronic (nuclear) spin1 Pauli vector, and the zaxis runs along the NV centre symmetry axis. Perpendicular strain couples the and spin states with a strength in the ES and /2π=21.5±1.2 GHz per strain in the GS (ref. 17). As shown in Fig. 1a, this interaction enables direct control of the magneticallyforbidden ← spin transition within each orbital through resonant strain.
Device details
The combination of a large hyperfine splitting in the ES and a short ES lifetime broadens the spectral features of the ES spin–strain interaction. Measuring such a spectrum then requires large magnetic field sweeps , which in turn require a mechanical driving field with a high carrier frequency . To this end, we fabricate a highovertone bulk acoustic resonator (HBAR) capable of generating large amplitude strain at gigahertzscale frequencies. The resonator used in this work was driven at a ω_{m}/2π=529 MHz mechanical mode that has a quality factor of Q=1,790±20. An antenna fabricated on the opposite diamond face provides highfrequency magnetic fields for magnetic spin control. The final device is pictured in Fig. 1b.
Spin–strain spectroscopy
To measure mechanical spin driving within the ES, we execute the pulse sequences shown in Fig. 2a, as a function of the magnetic bias field B_{z}. In the first sequence, a 532 nm laser initializes the NV centre ensemble into the GS level . A magnetic adiabatic passage (AP) then moves the spin population to . At this point, we pulse the mechanical resonator at its resonance frequency ω_{m} for 3 μs. Just before the end of the mechanical pulse, we apply a =125 ns optical pulse with the 532 nm laser. This excites the ensemble to and allows the spins to interact with the mechanical driving field in the ES. If the driving field is resonant with the ← splitting, population will be driven into . The spins then follow either a spinconserving relaxation down to or a relaxation to the singlet state through an intersystem crossing. The former preserves the spin state information, while relaxing to reinitializes the state, erases the stored signal and reduces the overall contrast of the measurement. After allowing the ensemble to relax, we apply the second magnetic AP to return the spin population in to and measure the population via fluorescence read out. We define this signal as S_{1} and plot it as a function of in Fig. 2b.
In the second pulse sequence, the mechanical pulse occurs between the second AP and fluorescence read out. Applying the mechanical pulse with the ensemble in maintains the same power load on the device but does not drive spin population. This sequence measures S_{2}, the reinitialization of the ensemble from the optical pulse (Fig. 2b). Subtracting S_{2}−S_{1} gives the probability of finding the ensemble in at the end of the first sequence. A third sequence with a single AP and a fourth with two APs (both with =0) normalize the spin contrast at each B_{z}.
Figure 2c shows the resulting experimental signal. The three broad, low peaks correspond to the hyperfinesplit → transition, providing definitive evidence of a spin–strain interaction within the room temperature ES. Population is also driven into by the GS spin–strain interaction when the mechanical driving field is resonant with the ← splitting. Figure 2c thus contains both ES and GS spectra. We fit the data to the sum of three low, broad Lorentzians describing the ES spin–strain interaction and three taller, narrower Lorentzians describing the GS interaction (see Methods). Figure 2d highlights the GS driving with a zoomed in view of Fig. 2c about the GS resonances. The GS peaks have larger amplitudes than the ES peaks because the GS interaction acts for the entire duration of the 3 μs mechanical pulse, whereas the ES interaction only acts during the ∼125 ns that the spin population is in the ES. Also, the reversed sign of relative to is consistent with ab initio calculations^{40} and was confirmed by measurements presented in Supplementary Note 1 that were conditional on the nuclear spin state.
Quantification of
To quantify the strength of the ES spin–phonon interaction, we first calibrate the strain amplitude generated by the HBAR by mechanically driving Rabi oscillations within the GS and extracting the GS mechanical Rabi field Ω_{g} as a function of the applied power (Fig. 3a). Next, we spectrally isolate the ← transition by fixing B_{z}=80 G. At this field, the applied strain is on resonance in the ES but off resonance in the GS (Fig. 2c). We then execute a modified version of the pulse sequence described above. Here, we use ∼20 ns magnetic πpulses to address the ← transition and measure both S_{1} and S_{2} as a function of for each power level applied to the HBAR.
As Fig. 3b shows, taking S_{2}−S_{1} reveals a competition between mechanical driving into and reinitialization into via optical pumping. For nonzero , the ES mechanical driving field Ω_{e} drives spin population from to , increasing , but as grows, optical pumping reinitializes the ensemble into , vacating the m_{s}={+1, −1} subspace and reducing to zero. A sevenlevel master equation model recreates this competition and provides good fits to the data. From these fits, we extract the value of Ω_{e}. The Methods section includes a detailed description of this model, which was designed to account for inhomogeneities within the NV centre ensemble and for the polarization of the nuclear spin sublevels, among other effects. Plotting Ω_{e} against Ω_{g} (Fig. 3c) shows that the transverse spin–strain coupling in the ES is 13.5±0.5 times stronger than the GS coupling, or /2π=290±20 GHz per strain.
Resonator cooling protocol
With quantified, we now present a dissipative protocol for cooling a mechanical resonator with an NV centre spin ensemble. In our proposed protocol, a 532 nm laser continuously pumps the phonon sidebands of the ensemble’s optical transition, and a gigahertz frequency magnetic field continuously drives the ← spin transition. This generates a steady state population surplus in as compared with , enabling the net absorption of phonons by the ensemble. Spontaneous relaxation and subsequent optical pumping continually reinitialize the system, allowing the phonon absorption cycle to continue. Figure 4a summarizes this process.
The dissipative nature of this protocol enables resonator cooling without requiring strong spinphonon coupling. Here, we define strong coupling as a singlespin cooperativity , where λ is the single spinsingle phonon coupling strength, is the inhomogeneous spin dephasing time, γ=ω_{m}/Q is the mechanical dissipation rate and is the thermal phonon occupancy of the resonator mode^{41}. A cooperativity of η>1 marks the threshold for coherent interactions between the spin and the mechanical mode. Nonidealities in spin coherence and resonator fabrication have thus far prevented the experimental realization of NV centre cooperativities approaching unity, especially at room temperature. This makes the proposed dissipative protocol a practical and attractive approach because it does not require coherent interactions for resonator cooling to occur.
To analyse the performance of the protocol we start by considering a single twostate spin system coupled to a mechanical resonator. The resulting dynamics obey the master equation (ħ=1)
where H describes the coherent coupling between the spin and the resonator, describes the incoherent spin processes, and describes the resonator rethermalization. For resonant coupling, the quantized Hamiltonian in the Jaynes–Cummings form is^{42}
where a^{†} (a) is the creation (annihilation) operator for the mechanical mode and S_{±} are the ladder operators for the spin state. The spin relaxation term in equation (2) takes the form , where is the Lindblad superoperator and T_{1} is the transverse (longitudinal) spin coherence time. The resonator rethermalization is described by .
Within this twostate model, an analytic expression for the steady state phonon number n_{f} can be found by using the matrix of second order moments (Supplementary Note 3)^{43}. Under the secular approximation and working in the limit , the dynamical equation for the phonon occupancy n=<a^{†}a> can be simplified to
For an ensemble of N spins coupled to the resonator but not to one another, each spin will add an additional damping term to the resonator dynamical equation. This allows us to rewrite the last term in equation (4) as . If each spin within the ensemble has the same T_{1} and , we can factorize this expression and replace the individual λ_{i} with an effective ensembleresonator coupling . For the case of uniform coupling, this simplifies to , which is equivalent to the effective coupling in the Tavis–Cummings model^{44,45}. Solving for the steady state of the system then gives
The problem now becomes mapping the sevenlevel NV centre structure pictured in Fig. 4a onto this twostate spin system. We do this by distilling the sevenlevel landscape to a toy model that contains only the twostates that couple to the mechanical resonator, and , as shown in Fig. 4b. Within this simplified landscape, we assign to be the ES coherence time (=6.0 ns (ref. 46)) and T_{1} to be the ES lifetime of (T_{1e}=6.89 ns (ref. 47)). At any one moment, only a fraction α of the spins within the ensemble will be in the proper subspace to participate in the cooling. We account for this by modifying . To determine α, we solve for the 7 × 7 density matrix describing the steady state of the ensemble in the absence of the mechanical resonator, calculate the population difference between and , and obtain α=0.017 for optimized control fields (Supplementary Note 4).
Elasticity theory provides a means of calculating the remaining device parameters. For a doublyclamped beam of length l, thickness t and width w, we compute λ_{eff} from the strain because of the zeropoint motion of the resonator (y, z) with coordinates as defined in Fig. 4c (see Methods). For a uniform distribution of properly aligned NV centres at a density ν, we obtain^{41,48}
Evaluating equation (6), we find that λ_{eff} is independent of w and scales as where , κ_{0}=120 GHz·μm, and E=1,200 GPa is the Young’s modulus of diamond. The frequency of the resonator’s fundamental mode scales as ω_{m}=κ_{0}t/l^{2}. As described in Supplementary Note 5, higher order mechanical modes are spectrally isolated from the NV centre spin dynamics in the devices considered here^{17,41}. For any thinbeam resonator in the resolvedsideband regime , the fractional cooling n_{f}/n_{th} is insensitive to the physical dimensions of the resonator because the size of the ensemble scales with the size of the resonator. This can be seen by rewriting equation (5) as n_{f}/n_{th}=(1+χ)^{−1}, where is independent of the resonator dimensions. For illustrative purposes, we choose to examine a resonator with a ω_{m}/2π=1 GHz fundamental mode and assume fully polarized nuclear spins^{49}. Potential device dimensions then become (l, t)=(1.9, 0.19) μm. Finally, phonon–phonon interactions limit the Q of an ideal diamond mechanical resonator at room temperature. For modes satisfying ω_{m}/2π >1/, the maximum Q=2 × 10^{6} is independent of ω_{m} (ref. 50), and we now have all the parameters needed to study the performance of the protocol.
At this point, we note that distilling a sevenstate model to the toy model we employ certainly requires validation. To justify our simplified model, we calculate the cooling predicted within the toy model and compare this both to an analytical Lamb–Dicke treatment of the sevenlevel model^{14,51} and to numerical simulations of a small number of sevenlevel NV centres coupled to a resonator. Because of the exponential growth of the Hilbert space, full sevenlevel numerical simulations were performed on the Titan supercomputer at Oak Ridge National Laboratory, with the most intensive simulations taking ∼10^{4} corehours. Comparing the toy model and Lamb–Dicke results to the numerical simulations, we determined that the twolevel distillation outperforms the Lamb–Dicke approach in all test cases and provides an upper bound on n_{f} (Supplementary Note 6). This indicates that the proposed protocol cools a resonator more efficiently than our toy model predicts^{52,53,54,55}.
Cooling performance
The lowest phonon occupancy that can be reached depends strongly on the density of properly aligned NV centres ν. For instance, Choi, et al. reported measurements of an NV centre ensemble with ν=2.0 × 10^{18} cm^{−3} in singlecrystal diamond^{56}. For this density and Q=2 × 10^{6}, we find that the proposed protocol cools a room temperature resonator to n_{f}=0.86n_{th}. Using the same Q and the density of ν=4 × 10^{20} cm^{−3} reported by Baranov, et al. in nanodiamonds^{57}, however, the protocol can cool to n_{f}=0.03n_{th}.
Increasing the size of the ensemble can thus dramatically increase the protocol’s cooling power. The magnetic field noise from paramagnetic impurities will also grow with ν, degrading the GS coherence time. However, for large magnetic driving fields, this cooling protocol does not require a lengthy GS coherence time (Supplementary Note 4). The only coherence time that effects the protocol is , which is not expected to change with the defect density^{34,37}. This means that large NV centre densities could in principle be used to cool a resonator with the ES spin–strain interaction. To study how increasing ν affects the protocol, we plot n_{f} against ν in Fig. 4d for several different Qvalues. For reference, we have included lines marking values of ν that have been realized in singlecrystal diamonds^{31,56,58} and in nanodiamonds^{57}. The limiting density of NV centres in a singlecrystal diamond nanostructure is currently unknown. Furthermore, while high defect densities have been shown to degrade the Q of frequency resonators^{59}, it remains to be seen how the gigahertz frequency resonators of interest here will be affected by the incorporation of a dense defect ensemble. These questions motivate future experimental work.
Discussion
The insensitivity of the proposed protocol to the GS coherence time makes an ES cooling protocol an attractive and practical route to cooling a room temperature mechanical resonator with NV centres. Alternative approaches that use the GS spin–strain coupling^{18,19,25} are incompatible with the collective enhancement from a dense ensemble that makes the proposed protocol viable. Although the GS inhomogeneous dephasing time can be ∼μs long in high purity diamonds, scales roughly as in bulk diamond and can be <100 ns for dense ensembles^{30,31}. Within a nanostructure, effects such as exchange narrowing and the truncation of the spin bath mitigate this reduction in (refs 57, 60) and make it difficult to predict the decrease in inside a doublyclamped beam. Nevertheless, we can roughly compare the ES and GS spin–strain interactions by calculating η using coherence times measured in bulk diamond (Supplementary Note 7). For a moderate NV centre density of ν=2.8 × 10^{13} cm^{−3} (ref. 18), the singlespin cooperativity for the ES spin–strain interaction is 2.4times larger than in the GS, and for ν=7.0 × 10^{17} cm^{−3} (ref. 31), η is 19times larger in the ES. In both cases, the ES offers the more efficient route to cooling, and as the collective enhancement grows, the ES interaction becomes increasingly more efficient than the GS interaction. A dense ensemble coupled via the ES spin–strain interaction thus becomes the more promising route to cooling a room temperature mechanical resonator with NV centres.
It is important to note that this analysis of the proposed protocol only applies for operation at room temperature. Reducing the bath temperature will lower n_{th} and would thus ideally lower n_{f}. However, the ES coherence time is limited by the ES motional narrowing rate, which increases as the bath temperature decreases^{34,37}. This is expected to lead to a reduction in at lower temperatures, followed by a complete loss of ES spin coherence below ∼150 K (ref. 32). As seen from equation (5), a reduction in will lead to a loss of cooling power. For cryogenic starting temperatures, it thus becomes necessary to use either the GS spinphonon interaction or the orbitalstrain interaction to cool a mechanical resonator with NV centres.
Finally, n_{f} could be lowered further by simultaneously implementing an optomechanical cooling protocol^{8,9,10,11,12} alongside the proposed protocol. Optomechanical cooling has been demonstrated to cool gigahertz frequency resonators to (refs 6, 61). The cooling rate from an optimized realization of the proposed protocol would combine additively with the optomechanical cooling rate, allowing the two complementary techniques to operate in conjunction and enhance the total cooling.
In conclusion, we have proposed a dissipative protocol for cooling a room temperature mechanical resonator that utilizes an ensemble of NV centre spins to realize a collective enhancement in the spinphonon coupling. After experimentally determining that the spin–strain coupling in the room temperature ES is 13.5±0.5 times stronger than the GS spin–strain coupling, we analysed the performance of the cooling protocol. For very dense NV centre ensembles, the proposed protocol can cool a room temperature resonator to a fraction of its thermal phonon occupancy. These results shed further light on the orbitallyaveraged room temperature ES of the NV centre and demonstrate a practical path towards cooling a room temperature mechanical resonator with NV centres.
Methods
Sample details
Our HBAR consists of a 2.5 μmthick ZnO piezoelectric film sandwiched between a 25/200 nm Ti/Pt ground plane and a 250 nm thick apodized Al top electrode, all sputtered on one face of a <100> singlecrystal diamond substrate. Applying a highfrequency voltage to this transducer launches acoustic waves into the diamond, which then serves as a Fabry–Pérot cavity to generate a comb of standing wave resonances. By apodizing the shape of the Al electrode, we mitigate the loss of power into lateral modes formed across the diameter of the HBAR. The antenna fabricated on the opposite diamond face was patterned from 25/225 nm Ti/Pt with a liftoff process.
The CVDgrown diamond used in these measurements contained NV centres at a density of ∼4 × 10^{14} cm^{−3} as purchased. Our measurements thus address an ensemble of ∼70 NV centres oriented with their symmetry axis parallel to B_{z}. NV centres of different orientations are spectrally isolated and contribute only a constant background to the measurements.
Spectrum fitting
The spectrum pictured in Fig. 2 was fit to the function
where c_{e} and c_{g} are constant amplitudes that quantify the driven spin contrast for the ES and GS resonances, a_{i}[B_{z}] are fielddependent scaling factors that account for the dynamic nuclear polarization of the hyperfine sublevels^{49}, Γ_{e} (Γ_{g}) is the FWHM of the ES (GS) resonances, B_{0} is the resonant field for the m_{I}=0 hyperfine sublevel, and the other parameters are as defined above. Of these variables, c_{i}, Γ_{i}, and B_{0} are free parameters in our fitting procedure.
We calibrate a_{i}[B_{z}] by performing hyperfineresolved magneticallydriven electron spin resonance (ESR) measurements within the NV centre GS at different values of the magnetic bias field B_{z}. This is done by fixing B_{z} and monitoring the NV centre photoluminescence as the carrier frequency of a magnetic driving field oriented along B_{x} is swept through the ← spin resonance. We fit the resulting curves to the function
where P is the measured photoluminescence, C accounts for the driven spin contrast, A_{i} is the relative amplitude of each hyperfine sublevel, P_{0} is the background photoluminescence, and we fix ∑ A_{i}=1. Figure 5a,b shows ESR curves measured at B_{z}=20.2 G and 171 G. We have used the values of P_{0} returned from the fits to normalize the photoluminescence.
Figure 5c shows the normalized amplitude of each nuclear sublevel plotted as a function of B_{z}. As expected, the nuclear polarization increases in the direction of the ES level anticrossing at =507 G. In this figure, we have fit each curve to a straight line with a fixed yintercept of to obtain the linear scaling functions a_{i}[B_{z}] in equation (7). The sum of these scaling functions satisfies ∑ a_{i}[B_{z}]=1.
Sevenlevel master equation model
The master equation used to model our ES spin driving measurements is derived in the room temperature NV centre basis defined by the states where, within the e and g subspaces, a subscript denotes the m_{s} value. The 7 × 7 density matrix evolves according to (ħ=1)
In the rotating frame, the Hamiltonian is given by
where Δ_{m} is the mechanical detuning. The incoherent NV centre processes are described by the superoperator
where we define
Here, Γ_{opt} is the optical pumping rate of our 532 nm laser, =6.0±0.8 ns is the ES coherence time^{46}, and the relaxation rates k_{ij} are listed in Table 1. Figure 6a summarizes this landscape^{47}.
Because optical initialization does not generate a pure state, we first simulate the optical pumping process to obtain an initialized density matrix. To do so, we start with a thermal state and apply equation (9) with Ω_{e}, Δ_{m}=0 and Γ_{opt}≠0 for 10 μs. We take the resulting density matrix and apply equation (9) for 5 μs with Ω_{e}, Δ_{m}, Γ_{opt}=0 to simulate the relaxation to . A simulated πpulse then swaps ρ_{22} and ρ_{33}, providing the appropriate starting density matrix ρ_{0} for a given Γ_{opt}. From ρ_{0}, we also extract the minimum and maximum spin contrast ( and ), which allow us to properly normalize our simulations.
Next, we model the measurement of S_{2}, the spin reinitialization. To do so, we apply equation (9) to ρ_{0} with Ω_{e}, Δ_{m}=0 and Γ_{opt}≠0 for a length of time . Allowing the spin to relax as before gives us the measured density matrix ρ_{2}. We normalize using s_{min} and s_{max}, and repeat this simulation as a function of to obtain a simulated S_{2} curve.
To account for spatial inhomogeneities in the optical power within the NV centre ensemble, we perform a weighted average of this simulation over the point spread function (PSF) of our microscope. We approximate the PSF by the function
where Γ_{0} is the peak optical pumping rate, κ[z_{0}] defines the depthdependent PSF width^{15}, z is the distance below the diamond surface, and z_{0}=7.9±0.9 μm is the focus depth of the PSF. An ensemble measurement is then given by
We discretize this integral to make it computationally tractable and perform a least squares fit of to the measured data. Γ_{0} is the only free parameter in the fitting procedure.
With the exception of the datum indicated in Fig. 6b, all of the measurements were taken at the same optical power. We simultaneously fit each of these S_{2} curves and find Γ_{0}=19.1±1.6 MHz. For the measurement at a different optical power, we find Γ_{0}=16.5±1.7 MHz.
To extract Ω_{e}, we then fix Γ_{0} and repeat this procedure with Ω_{e}≠0 to simulate the S_{2}−S_{1} measurement pictured in Fig. 3b. To account for inhomogeneities in the mechanical driving field, we must also include the spatial profile of the strain standing wave inside the weighted average. This function takes the form where λ=31±4 μm is the wavelength of the strain wave. Defining the results of such a simulation as (Ω_{e}, Δ_{m}), we account for the hyperfine sublevels by computing the sum
where the normalized amplitudes (∑ a_{i}=1) account for nuclear spin polarization and have been measured separately via magnetic ESR. A least squares fit of equation (15) to the data then provides Ω_{e}. Here, Ω_{e} is the only free parameter in the fitting procedure.
When fitting the relation between Ω_{e} and Ω_{g} (Fig. 3c), we fix the yintercept of the linear fitting function to be zero.
Elasticity theory
To analyse how strain couples to NV centres within a resonator, we start by assuming that the NV centres are aligned with the direction of beam deflection such that the strain in an oscillating beam is entirely perpendicular to the NV centre symmetry axis. We then use elasticity theory to derive the scaling laws quoted above^{17,41}.
The wave equation for doublyclamped beams is
where φ(t, z) is the transverse displacement in the ydirection, points along the beam as indicated in Fig. 4c, A=wt is the crosssectional area of the resonator, E=1,200 GPa is the Young’s modulus of diamond, ρ_{d}=3.515 g cm^{−3} is the mass density of diamond, and I=wt^{3}/12 is the resonator’s moment of inertia. Solutions are of the form φ(z, t)=u(z)e^{−iωt} where
and the allowed kvectors satisfy cos(k_{n}z) cosh(k_{n}z)=1. The wave vector and amplitudes of the fundamental mode satisfy k_{0}l=4.73 and a_{0}/b_{0}=1.0178.
We normalize u_{n}(z) by setting the free energy of the beam equal to the zero point energy of the mode:
where the eigenfrequencies of the resonator are given by . This expression for ω_{n} can be simplified to ω_{n}=κ_{n}t/l^{2}, where . For the fundamental mode, κ_{0}=120 GHz·μm as quoted above.
The spinphonon coupling for a single NV centre located at (y, z) is given by λ=d_{⊥}(y, z) where is the strain from the zero point motion of the resonator mode. Here, the yaxis is zeroed at the neutral axis of the resonator. To compute the effective ensembleresonator coupling, we assume a uniform distribution of properly aligned NV centres within the resonator and sum the individual couplings in quadrature according to , which gives equation (6).
Data availability
The data that support the findings of this study are available from the corresponding author on reasonable request.
Additional information
How to cite this article: MacQuarrie, E. R. et al. Cooling a mechanical resonator with nitrogenvacancy centres using a room temperature excited state spin–strain interaction. Nat. Commun. 8, 14358 doi: 10.1038/ncomms14358 (2017).
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Change history
29 November 2017
A correction has been published and is appended to both the HTML and PDF versions of this paper. The error has not been fixed in the paper.
References
 1
Albrecht, T. R., Grütter, P., Horne, D. & Rugar, D. Frequency modulation detection using highQ cantilevers for enhanced force microscope sensitivity. J. Appl. Phys. 69, 668–673 (1991).
 2
Cleland, A. N. & Roukes, M. L. A nanometrescale mechanical electrometer. Nature 392, 160–162 (1998).
 3
Rugar, D., Budakian, R., Mamin, H. J. & Chui, B. W. Single spin detection by magnetic resonance force microscopy. Nature 430, 329–332 (2004).
 4
Poggio, M., Degen, C. L., Mamin, H. J. & Rugar, D. Feedback cooling of a cantilever’s fundamental mode below 5 mk. Phys. Rev. Lett. 99, 017201 (2007).
 5
O’Connell, A. D. et al. Quantum ground state and singlephonon control of a mechanical resonator. Nature 464, 697–703 (2010).
 6
Chan, J. et al. Laser cooling of a nanomechanical oscillator into its quantum ground state. Nature 478, 89–92 (2011).
 7
Teufel, J. D. et al. Sideband cooling of micromechanical motion to the quantum ground state. Nature 475, 359–363 (2011).
 8
Metzger, C. H. & Karrai, K. Cavity cooling of a microlever. Nature 432, 1002–1005 (2004).
 9
Gigan, S. et al. Selfcooling of a micromirror by radiation pressure. Nature 444, 67–70 (2006).
 10
Arcizet, O., Cohadon, P.F., Briant, T., Pinard, M. & Heidmann, A. Radiationpressure cooling and optomechanical instability of a micromirror. Nature 444, 71–74 (2006).
 11
Kleckner, D. & Bouwmeester, D. SubKelvin optical cooling of a micromechanical resonator. Nature 444, 75–78 (2006).
 12
Schliesser, A., Del’Haye, P., Nooshi, N., Vahala, K. J. & Kippenberg, T. J. Radiation pressure cooling of a micromechanical oscillator using dynamical backaction. Phys. Rev. Lett. 97, 243905 (2006).
 13
Rabl, P. et al. Strong magnetic coupling between an electronic spin qubit and a mechanical resonator. Phys. Rev. B 79, 041302 (2009).
 14
Kepesidis, K. V., Bennett, S. D., Portolan, S., Lukin, M. D. & Rabl, P. Phonon cooling and lasing with nitrogenvacancy centers in diamond. Phys. Rev. B 88, 064105 (2013).
 15
MacQuarrie, E. R., Gosavi, T. A., Jungwirth, N. R., Bhave, S. A. & Fuchs, G. D. Mechanical spin control of nitrogenvacancy centers in diamond. Phys. Rev. Lett. 111, 227602 (2013).
 16
Teissier, J., Barfuss, A., Appel, P., Neu, E. & Maletinsky, P. Strain coupling of a nitrogenvacancy center spin to a diamond mechanical oscillator. Phys. Rev. Lett. 113, 020503 (2014).
 17
Ovartchaiyapong, P., Lee, K. W., Myers, B. A. & Jayich, A. C. B. Dynamic strainmediated coupling of a single diamond spin to a mechanical resonator. Nat. Commun. 5, 4429 (2014).
 18
MacQuarrie, E. R. et al. Coherent control of a nitrogenvacancy center spin ensemble with a diamond mechanical resonator. Optica 2, 233–238 (2015).
 19
Barfuss, A., Teissier, J., Neu, E., Nunnenkamp, A. & Maletinsky, P. Strong mechanical driving of a single electron spin. Nat. Phys. 11, 820–824 (2015).
 20
MacQuarrie, E. R., Gosavi, T. A., Bhave, S. A. & Fuchs, G. D. Continuous dynamical decoupling of a single diamond nitrogenvacancy center spin with a mechanical resonator. Phys. Rev. B 92, 224419 (2015).
 21
Golter, D. A., Oo, T., Amezcua, M., Stewart, K. A. & Wang, H. Optomechanical quantum control of a nitrogenvacancy center in diamond. Phys. Rev. Lett. 116, 143602 (2016).
 22
Lee, K. W. et al. Strain coupling of a mechanical resonator to a single quantum emitter in diamond. Phys. Rev. Appl. 6, 034005 (2016).
 23
Burek, M. J. et al. Diamond optomechanical crystals. Optica 3, 1404–1411 (2016).
 24
Khanaliloo, B. et al. Singlecrystal diamond nanobeam waveguide optomechanics. Phys. Rev. X 5, 041051 (2015).
 25
Meesala, S. et al. Enhanced strain coupling of nitrogenvacancy spins to nanoscale diamond cantilevers. Phys. Rev. Appl. 5, 034010 (2016).
 26
Mitchell, M. et al. Singlecrystal diamond lowdissipation cavity optomechanics. Optica 3, 963–970 (2016).
 27
Ma, Y., Yin, Z., Huang, P., Yang, W. L. & Du, J. Cooling a mechanical resonator to the quantum regime by heating it. Phys. Rev. A. 94, 053836 (2016).
 28
Lau, H.K. & Plenio, M. B. Laser cooling of a hightemperature oscillator by a threelevel system. Phys. Rev. B 94, 054305 (2016).
 29
Fu, K.M. C. et al. Observation of the dynamic JahnTeller effect in the excited states of nitrogenvacancy centers in diamond. Phys. Rev. Lett. 103, 256404 (2009).
 30
Kittel, C. & Abrahams, E. Dipolar broadening of magnetic resonance lines in magnetically diluted crystals. Phys. Rev. 90, 238–239 (1953).
 31
Acosta, V. M. et al. Diamonds with a high density of nitrogenvacancy centers for magnetometry applications. Phys. Rev. B 80, 115202 (2009).
 32
Batalov, A. et al. Low temperature studies of the excitedstate structure of negatively charged nitrogenvacancy color centers in diamond. Phys. Rev. Lett. 102, 195506 (2009).
 33
Rogers, L. J., McMurtrie, R. L., Sellars, M. J. & Manson, N. B. Timeaveraging within the excited state of the nitrogenvacancy centre in diamond. New J. Phys. 11, 063007 (2009).
 34
Plakhotnik, T., Doherty, M. W. & Manson, N. B. Electronphonon processes of the nitrogenvacancy center in diamond. Phys. Rev. B 92, 081203 (2015).
 35
Fuchs, G. D. et al. Excitedstate spectroscopy using single spin manipulation in diamond. Phys. Rev. Lett. 101, 117601 (2008).
 36
Doherty, M. W. et al. The nitrogenvacancy colour centre in diamond. Phys. Rep 528, 1 (2013).
 37
Fuchs, G. D. et al. Excitedstate spin coherence of a single nitrogenvacancy centre in diamond. Nat. Phys. 6, 668–672 (2010).
 38
Slichter, C. P. in Principles of Magnetic Resonance 3rd edn Springer (1990).
 39
Steiner, M., Neumann, P., Beck, J., Jelezko, F. & Wrachtrup, J. Universal enhancement of the optical readout fidelity of single electron spins at nitrogenvacancy centers in diamond. Phys. Rev. B 81, 035205 (2010).
 40
Gali, A., Fyta, M. & Kaxiras, E. Ab initio supercell calculations on nitrogenvacancy center in diamond: electronic structure and hyperfine tensors. Phys. Rev. B 77, 155206 (2008).
 41
Bennett, S. D. et al. Phononinduced spinspin interactions in diamond nanostructures: application to spin squeezing. Phys. Rev. Lett. 110, 156402 (2013).
 42
Jaynes, E. T. & Cummings, F. W. Comparison of quantum and semiclassical radiation theories with application to the beam maser. Proc. IEEE 51, 89–109 (1963).
 43
WilsonRae, I., Nooshi, N., Dobrindt, J., Kippenberg, T. J. & Zwerger, W. Cavityassisted backaction cooling of mechanical resonators. New J. Phys. 10, 095007 (2008).
 44
Tavis, M. & Cummings, F. W. Exact solution for an Nmoleculeradiationfield Hamiltonian. Phys. Rev 170, 379–384 (1968).
 45
Garraway, B. M. The Dicke model in quantum optics: Dicke model revisited. Philos. Trans. R. Soc. Lond. A: Math. Phys. Eng. Sci. 369, 1137–1155 (2011).
 46
Fuchs, G. D., Falk, A. L., Dobrovitski, V. V. & Awschalom, D. D. Spin coherence during optical excitation of a single nitrogenvacancy center in diamond. Phys. Rev. Lett. 108, 157602 (2012).
 47
Robledo, L., Bernien, H., van der Sar, T. & Hanson, R. Spin dynamics in the optical cycle of single nitrogenvacancy centres in diamond. New J. Phys. 13, 025013 (2011).
 48
Schuster, D. I. et al. Highcooperativity coupling of electronspin ensembles to superconducting cavities. Phys. Rev. Lett. 105, 140501 (2010).
 49
Jacques, V. et al. Dynamic polarization of single nuclear spins by optical pumping of nitrogenvacancy color centers in diamond at room temperature. Phys. Rev. Lett. 102, 057403 (2009).
 50
Tabrizian, R., RaisZadeh, M. & Ayazi, F. Effect of phonon interactions on limiting the f.Q product of micromechanical resonators. in SolidState Sensors, Actuators and Microsystems Conference. TRANSDUCERS 2009, 2131–2134 (IEEE, 2009).
 51
Jaehne, K., Hammerer, K. & Wallquist, M. Groundstate cooling of a nanomechanical resonator via a Cooperpair box qubit. N. J. Phys. 10, 095019 (2008).
 52
Otten, M. et al. Entanglement of two, three, or four plasmonically coupled quantum dots. Phys. Rev. B 92, 125432 (2015).
 53
Saad, Y. & Schultz, M. GMRES: a generalized minimal residual algorithm for solving nonsymmetric linear systems. SIAM J. Sci. Stat. Comput. 7, 856–869 (1986).
 54
Balay, S. et al. PETSc users manual. Tech. Rep. ANL95/11  Revision 3.7, (Argonne National Laboratory, 2016).
 55
Balay, S., Gropp, W. D., McInnes, L. C. & Smith, B. F. in Modern Software Tools in Scientific Computing (eds Arge, E., Bruaset, A. M. & Langtangen, H. P.), 163–202 (Birkhäuser Press, 1997).
 56
Choi, S. et al. Depolarization dynamics in a strongly interacting solidstate spin ensemble. Preprint at http://arxiv.org/abs/1608.05471 (2016).
 57
Baranov, P. G. et al. Enormously high concentrations of fluorescent nitrogenvacancy centers fabricated by sintering of detonation nanodiamonds. Small 7, 1533–1537 (2011).
 58
Wee, T.L. et al. Twophoton excited fluorescence of nitrogenvacancy centers in protonirradiated type Ib diamond. J. Phys. Chem. A 111, 9379–9386 (2007).
 59
Tao, Y., Boss, J. M., Moores, B. A. & Degen, C. L. Singlecrystal diamond nanomechanical resonators with quality factors exceeding one million. Nat. Commun. 5, 3638 (2014).
 60
Smith, M. J. A., Angel, B. R. & Emmons, R. G. Distribution of substitutional nitrogen donors in synthetic diamonds. Nature 210, 692–694 (1966).
 61
SafaviNaeini, A. H. et al. Observation of quantum motion of a nanomechanical resonator. Phys. Rev. Lett. 108, 033602 (2012).
Acknowledgements
Research support was provided by the Office of Naval Research (ONR) (Grant N000141410812). Device fabrication was performed in part at the Cornell NanoScale Science and Technology Facility, a member of the National Nanotechnology Coordinated Infrastructure, which is supported by the National Science Foundation (Grant ECCS15420819), and at the Cornell Center for Materials Research Shared Facilities which are supported through the NSF MRSEC program (DMR1120296). Numerical simulations were performed in part at the Centre for Nanoscale Materials, a U.S. Department of Energy Office of Science User Facility under contract no. DEAC0206CH11357. This research used resources of the Oak Ridge Leadership Computing Facility at the Oak Ridge National Laboratory, which is supported by the Office of Science of the U.S. Department of Energy under Contract No. DEAC0500OR22725.
Author information
Affiliations
Contributions
E.R.M. and G.D.F. developed the concept and procedure for the experiment and the proposed cooling protocol. E.R.M. performed the experiments and analysed the data. E.R.M., M.O., S.K.G. and G.D.F. developed the toy model treatment of the proposed cooling protocol. M.O. and S.K.G. developed and performed the numerical simulations that validate the toy model treatment of the cooling protocol. E.R.M., M.O, S.K.G. and G.D.F. prepared the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Supplementary Information
Supplementary Figures, Supplementary Table 1, Supplementary Notes and Supplementary References (PDF 870 kb)
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
MacQuarrie, E., Otten, M., Gray, S. et al. Cooling a mechanical resonator with nitrogenvacancy centres using a room temperature excited state spin–strain interaction. Nat Commun 8, 14358 (2017). https://doi.org/10.1038/ncomms14358
Received:
Accepted:
Published:
Further reading

Improvement on the manipulation of a single nitrogenvacancy spin and microwave photon at singlequantum level
Communications in Theoretical Physics (2021)

Inhomogeneous response of an ion ensemble from mechanical stress
Physical Review Research (2020)

Mechanical Tunability of an Ultranarrow Spectral Feature of a RareEarthDoped Crystal via Uniaxial Stress
Physical Review Applied (2020)

Enhancing SpinPhonon and SpinSpin Interactions Using Linear Resources in a Hybrid Quantum System
Physical Review Letters (2020)

Cooling of mechanical resonator in a doublecavity system with twolevel atomic ensemble
Journal of Physics B: Atomic, Molecular and Optical Physics (2020)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.