Photoelectrochemical water splitting uses solar power to decompose water to hydrogen and oxygen. Here we show how the photocatalytic activity of thylakoid membranes leads to overall water splitting in a bio-photo-electro-chemical (BPEC) cell via a simple process. Thylakoids extracted from spinach are introduced into a BPEC cell containing buffer solution with ferricyanide. Upon solar-simulated illumination, water oxidation takes place and electrons are shuttled by the ferri/ferrocyanide redox couple from the thylakoids to a transparent electrode serving as the anode, yielding a photocurrent density of 0.5 mA cm−2. Hydrogen evolution occurs at the cathode at a bias as low as 0.8 V. A tandem cell comprising the BPEC cell and a Si photovoltaic module achieves overall water splitting with solar to hydrogen efficiency of 0.3%. These results demonstrate the promise of combining natural photosynthetic membranes and man-made photovoltaic cells in order to convert solar power into hydrogen fuel.
The need for cost effective and sustainable solutions for storing intermittent solar power has spurred a growing interest in artificial photosynthesis and solar fuels1,2,3. The most elementary solar fuel production process relies on the water–hydrogen cycle, . The forward reaction is work-consuming (endergonic). Under standard conditions it requires a minimum input of 237 kJ of entropy-free energy (that is, work) to dissociate one mole of water, which is the standard Gibbs free energy of the reaction (ΔG0). The reaction products, H2 and O2 gases, serve as fuel that can be stored in separate vessels and converted back into power by the reverse reaction. Thus, H2 can be produced sustainably by water electrolysis using renewable power sources such as solar power. Replacement of the entire worldwide primary energy consumption (12,910 million tons oil equivalent in 2014; ref. 4) by solar H2 produced at an average solar to hydrogen (STH) conversion efficiency of 1%, equivalent to the solar to biomass conversion efficiency of high efficiency crop plants5, would demand a net area of 9.7 million km−2 of solar collectors. This accounts for 6.5% of the total land area or 70.3% of the estimated arable land area on earth, a scenario which is not very practical6.
This limitation motivates research on other routes to store solar energy as chemical bonds in fuel products, for example through biotechnological or artificial photosynthesis processes. Bio-processes for renewable H2 production have been explored using fermentative and photosynthetic organisms as cellular factories for H2 production. Traditionally, these bio-processes are categorized into: (i) dark fermentation, (ii) photo-fermentation and (iii) biophotolysis7. Through the fermentative processes, protons serve as electron acceptors from catabolized organic compounds, while H2 production by biophotolytic processes make use of organisms capable of oxygenic photosynthesis, for example, green microalgae or cyanobacteria. For the latter, sunlight drives the oxidation of water molecules that serve as the electron donor, and protons generated are subsequently reduced to molecular hydrogen. A major barrier to commercialization of these technologies is the necessity to impose substantial restrictions on the bioreactor operating conditions in order to generate significant quantities of H2; H2 production with green algae occurs only under near anaerobic conditions, as the primary catalytic enzyme involved ((Fe–Fe)-hydrogenase) is inhibited by oxygen. Sustained H2 production using algae can be achieved only when photosynthetic O2 evolution is severely inhibited by sulfur deprivation, to such an extent that it equals the O2 consumption in the cellular respiration. Similarly, H2 production from filamentous or unicellular cyanobacteria requires the removal of O2 from the growth medium8.
The work described here puts forward a different approach that brings together light and photosynthetic membranes in a bio-photo-electro-chemical (BPEC) cell that generates, under illumination, an electromotive force that facilitates the water splitting reaction and funnels electrons and protons for the generation of H2. The operation of the BPEC cell requires the concerted operation of three components: (i) a photochemical module that captures light and produces separated charge carriers with excess chemical potential, (ii) a catalytic module that employs the photo-excited charge carriers to carry out endergonic oxidative or reductive chemistry, and (iii) an efficient method for transferring the charge carriers between the two modules while keeping as much of their excess free energy as possible8. In previous studies, photosystem I (PSI) complexes isolated from thermophilic cyanobacteria and tethered to either Pt nanoparticle catalyst9 or [NiFe]-hydrogenase10 were reported to produce up to 170 mol H2 (mol PSI min)−1, under illumination, in the presence of sacrificial electron donor (sodium ascorbate). McCormick et al.11 reported a BPEC cell that uses a two-step process to produce H2 at a rate of 2.4 μmol H2 (mg Chlh)−1, using live culture of the cyanobacteria Synechocystis PCC 6803, electron mediator (ferricyanide, Fe(III)CN), and a Pt cathode. Recently, Wang et al.12 reported the overall water splitting by self-assembled photosystem II (PSII) membranes on artificial catalysts, achieving H2 production rate of 9.1 μmol H2 (mg Chlh)−1. In this system, the PSII membranes were irreversibly attached to particles containing ruthenium or rhodium, along with other inorganic components, in the presence of Fe(III)CN. In another recent study, Mersch et al.13 presented a BPEC cell that couples PSII membranes and hydrogenase to mesoporous transparent electrodes, using 2,6-dichloro-1,4-benzoquinone (DCBQ) as an electron mediator. A benchmark water splitting photocurrent of 450 μA cm−2 was obtained at an applied bias of 0.9 V under red light illumination (λ=660 nm) at an intensity of 10 mW cm−2, corresponding to a light-to-hydrogen conversion efficiency of (1.5±0.1)%.
Unlike conventional (first generation) biofuel production technologies from crop plants, a process that has been reported to work at an average efficiency of up to 1% and creates a serious competition for food5, BPEC cells make use of leaves, and are not limited to a particular plant species. Leaves of most crops do not have high commercial value, being mostly used as feedstock. We envision the utilization of crop leaves for green and benign H2 production, as an intermediate step after the crop plant has given its fruits, and before being fed to animals. Thus, in this work we present a BPEC cell that produces H2 gas using crude thylakoid membranes (henceforth called thylakoids) extracted from spinach, which is used here as a plant model. The thylakoids are extracted with minimal preparatory effort and then applied simply by letting them settle onto the surface of a transparent electrode, thereby enabling easy replacement of photodamaged thylakoids by fresh ones. Under illumination, a photocurrent is produced, mediated by Fe(III)CN, and channelled to evolve H2 at the cathode at applied bias far below the reversible voltage of water electrolysis (1.23 V in standard conditions). Furthermore, we present a stand-alone mode of operation, wherein the BPEC cell is coupled in tandem to a Si photovoltaic (PV) module that provides the bias required to produce H2. Thus, H2 is produced by this hybrid tandem cell from oxidized water molecules without any external power source or sacrificial electron donors.
Our BPEC cell design meets the following principles: (i) Utilization of crude thylakoids without chemical immobilization or modification. This prevents the deleterious outcomes of immobilization procedures to the photosystems14, and therefore, it is expected to retain high photosynthetic activity, as well as enable easy replacement of photodamaged thylakoids; (ii) Utilization of a durable and inexpensive transparent electrode; and (iii) Use of a stable electron mediator (Fe(III)CN) to allow efficient electron extraction from the thylakoids and fast charge transfer to the anode11,12. The use of crude thylakoids purified from spinach in a BPEC cell is schematically illustrated in Fig. 1a. The anode is a transparent electrode made of fluorinated-tin-oxide (FTO) coated glass substrate onto which the thylakoids were applied simply by letting them to settle from a slurry of crude spinach thylakoids in buffer solution onto the anode. Figure 1b shows scanning electron microscopy images of the thylakoids on the FTO surface. For clarity of observation, only a small amount of thylakoids was used in the preparation of the scanning electron microscopy specimen. The thylakoids were not tightly attached to the anode, and could easily be washed away by gently flushing with buffer solution. Thus, stirring of the thylakoids during operation of the BPEC cell was impossible and not deemed critical for performance.
Significant photocurrent from spinach thylakoids
Under solar-simulated illumination, water oxidation is catalysed by the PSII complex embedded in the thylakoids, releasing O2 and protons. A mediated photocurrent is obtained in the system by use of the redox couple ferri/ferrocyanide (Fe(III)/Fe(II)CN) that extracts electrons from the photosynthetic membranes and transfers them to the anode. The photocurrent dependence on the applied potential is presented in Fig. 2a, showing saturation of 450±50 μA cm−2 at an anode potential of 0.5 VAg/AgCl. The measurements were carried out in buffer A solution with a thylakoid content of 0.1 mg Chl and a Fe(III)CN concentration of 3 mM. The dependencies of the photocurrent, measured at 0.5 VAg/AgCl, on the Fe(III)CN concentration (at a thylakoid content of 0.1 mg Chl) and thylakoid content (at a Fe(III)CN concentration of 3 mM) are presented in Fig. 2b,c, respectively. A maximal photocurrent density of ca. 0.5 mA cm−2 was obtained using 3 mM Fe(III)CN and thylakoid content of 0.1 mg Chl.
Previous reports have shown photo-induced electron transfer from PSII and PSI15 and the production of photocurrent from spinach thylakoids utilizing Fe(III)CN as electron shuttle, as well as using other thylakoid sources, different types of electron mediators, and a variety of electrode compositions. For example, Calkins et al.16 immobilized spinach thylakoids onto multi-walled carbon nanotubes, and achieved a maximal photocurrent of 68 μA using Fe(III)CN as the electron mediator. We have previously reported a photocurrent density of 100 μA cm−2 using a graphite electrode and DCBQ as an electron shuttle17. Hasan et al.18 reported a maximal photocurrent density of 130 μA cm−2 using a gold electrode and para-benzoquinone electron transfer mediator. Thylakoids have also been used without an electron mediator19,20, though the reported photocurrents were lower compared with reports with an electron mediator. Larom et al.21 reported the production of an unmediated photocurrent density of 16 μA cm−2 using crude Synechocystis membranes and N-acetyl cysteine-modified gold electrode. A photocurrent density of 42 μA cm−2 was reported by Hamidi et al.22, using immobilized spinach thylakoids in osmium polymer network on a graphite electrode. Other studies reported high photocurrents using purified PSI or PSII. A solid state electrochemical device23 that combines purified photosynthetic complexes with a transparent electrode coated with a sandwich of metallic nanolayers reached a photocurrent density of 120 μA cm−2. This study is mentioned in a recent review article on photosynthetic protein based PV devices24 as setting the record for these devices. Isolated PSII membranes were also employed by Mersch et al.13, reporting photocurrent densities as high as 930 μA cm−2 at an applied potential of 0.5 V versus the normal hydrogen electrode (NHE). However, the photocurrent in this study was measured under red light illumination (λ=679 nm, 10 mW cm−2), which makes it difficult to compare with our results that were measured under solar-simulated white light illumination. Hence, the photocurrent density reported here sets a new record for solar-simulated measurements of BPEC cells utilizing any photosynthetic membranes, crude or purified ones. Furthermore, the preparation of isolated reaction centers is expensive, time and energy consuming and requires the use of polluting detergents, and the photocurrent quickly decays due to irreversible degradation of the reaction centers13,16,18,19,22. Our approach alleviates these drawbacks by using crude thylakoids that can be readily replaced by fresh ones, as demonstrated below.
To estimate the efficiency of the charge transfer from the thylakoids to the electric circuit we calculated the ratio between the total photo-induced charge, Qphoto, measured by integrating the photocurrent (Iphoto) over time, , and the amount of O2 that evolved by the photosynthetic membranes, ΔO2 (measured in (mol O2)). Thus, the charge transfer efficiency (ηct) was calculated according to equation (1):
where F is the Faraday constant. In order to calculate ΔO2 we measured the increase in oxygen concentration after 10 min of illumination using a Clark electrode (see Supplementary Fig. 1a). The charge transfer efficiency was (94±11)% (Supplementary Fig. 1b). This value indicates that under these conditions almost all of the electrons derived from water photo-oxidation were successfully transferred to the electric circuit.
Fe(III)CN reduction by isolated chloroplasts or sub-chloroplast components is one of the early facilitators of the Hill reaction and has been known since the 1950’s. Studies have suggested that Fe(III)CN is reduced by several separate donor sites located in PSII, plastoquinone (PQ) and the cytochrome b6f or PSI25. Earlier studies have made clear that the reduction is accompanied by an adverse effect which rapidly inhibits photosynthesis. A dose-dependent perturbation of 20–50% in the oxygen evolution rate was reported for spinach chloroplasts that were dark-incubated in 0.5–20 mM Fe(III)CN for 20 min26. Furthermore, Kirilovsky et al.27 investigated the complex light-dependent PSII inactivation caused by Fe(III)CN incubation by electron paramagnetic resonance (EPR) spectroscopy and fluorescence induction techniques. Their report suggests that the inhibition is the result of a dual effect; the first one is the over-oxidation of the donor site in PSII, which uncouples the oxygen evolving center, and the second one is the formation of abnormal states of reduced QA at the acceptor site.
Here we study a system that exploits Fe(III)CN as an electron mediator from photo-activated thylakoids. As expected, photocurrent degradation was observed, especially at high photocurrent densities (see inset of Fig. 2b). Thus, we sought to elucidate the nature of the photocurrent degradation. Towards this end, spinach thylakoids were placed in the BPEC cell and incubated in light or dark in the presence or absence of ferricyanide (Fe(III)CN) or ferrocyanide (Fe(II)CN) as a control, and then used, subsequently, for photocurrent and photosynthetic electron flow measurements. Figure 3a presents the residual photocurrent that was measured following 10 min of different incubation treatments. The residual activities are expressed as the ratio between the photocurrent and PSII activities obtained after the incubation to those obtained in a control experiment using identical thylakoids without 10 min of incubation. Incubations in light or dark without Fe(III)CN were found to reduce the photocurrent to about 60 and 80% of the initial photocurrent, respectively, indicating that light enhances the degradation of the photocurrent. In addition, there is significantly more reduction of the photocurrent when the thylakoids are incubated with Fe(III)CN in the light, resulting with only 20% of the initial photocurrent (Fig. 3a). To rule out the possibility that the reduced form of the electrolyte, that is Fe(II)CN obtained from the reduction of Fe(III)CN in the light, degraded the photocurrent, thylakoids were also incubated with Fe(II)CN under the same conditions. The degradations that were observed following incubation with Fe(II)CN in the dark or light were comparable to that of thylakoids that were incubated without Fe(III)CN (Fig. 3a). This observation is consistent with reports that Fe(II)CN ions are harmless to chloroplast or sub-chloroplast components in the mM concentration range28.
Since the BPEC cell makes use of only a small amount of thylakoids in the presence of excess Fe(III)CN in solution, we hypothesized that the light-dependent photocurrent decay may have occurred as a result of the PSII membranes reaching their turnover number limit, after which PSII was damaged. To examine this hypothesis and to determine the fraction of photosynthetically active electron flow in the thylakoids in each of the incubation conditions, thylakoids were collected from the BPEC cell after 10 min of incubation, the Fe(III)CN was washed out by centrifugation, the thylakoids were re-suspended in fresh medium (as explained in the experimental procedures), and analysed for 2,6-dichlorophenolindophenol (DCPIP) reduction. The results are presented in Fig. 3a. There is correlation between the photocurrent degradation and the DCPIP reduction degradation. A residual photosynthetic electron flow activity of 10% was observed for thylakoids that were incubated with Fe(III)CN in light, compared with 60% of this activity that was retained in thylakoids that were incubated in light without Fe(III)CN. This observation suggests that the combination of light and Fe(III)CN is most harmful to the thylakoids, enhancing the photoinhibition of the photosynthetic electron flow. Thus, we conclude that the photocurrent degradation was caused in part by the photoinhibition deactivation of photosynthetic electron flow which is enhanced in the present of Fe(III)CN. Additional contribution of the Fe(III)CN to the degradation of the photocurrent and the photosynthetic electron flow occurred in the dark (Fig. 3a). In order to overcome the degradation problem, the thylakoids were replaced with fresh ones every 10 min in a time course of 1 h, while continuously monitoring the photocurrent. As shown in Fig. 3b, the photocurrent was kept at a high level throughout the entire hour, except for the intermittent exchange points every 10 min. This demonstrates that the electrodes and mediator solution may be reused for a long time.
The photocurrent is derived from photosynthetic electron transfer
To examine whether the source of electrons was indeed photosynthetic water photolysis and not spurious side reactions, the photosynthesis inhibitor 3-(3,4-dichlorophenyl)-1,1-dimethylurea (DCMU) was introduced to the system as a probe. DCMU is known to effectively block the electron transfer from QA to QB in PSII29,30, as illustrated in Fig. 4a (see also Supplementary Fig. 2). Hence, it inhibits continuous water photo-oxidation. Figure 4b shows the relative photocurrent with and without DCMU as a function of DCMU concentration. It is evident that an inhibitory effect governs the process, with a complete photocurrent arrest at 500 μM DCMU. The inhibition by DCMU implies that the source of electrons reducing the Fe(III)CN mediator must be at or down-stream the QB site, which is the site blocked by the herbicide30 (see Fig. 4a). Unlike the quinone acceptors DCBQ and DCPIP which accept electrons mostly from the quinone-binding sites of PSII (QB) and Cytochrome b6f (cyt b6f), Fe(III)CN can accept electrons from several electron donor sites under different conditions, including QA30, the PQ pool31, cyt b6f and PSI32. To further investigate the electron source of the reduction of Fe(III)CN in our system, we performed a series of experiments with the photosynthesis inhibitor 2,5-dibromo-6-isopropyl-3-methyl-1,4-benzoquinone (DBMIB). At low concentrations DBMIB blocks the electron transfer from the PQ pool to cyt b6f (refs 30, 33). This inhibition was observed in our system, as shown by the persistence of electron transfer from H2O to DCBQ but not from H2O to methyl viologen dichloride (MV) in the presence of 5 μM DBMIB, see Fig. 4c. DBMIB did not inhibit the photocurrent, as well as the H2O to Fe(III)CN electron transfer rate, indicating that Fe(III)CN extracts electrons before cyt b6f. Together with the observation that DCMU suppressed the photocurrent (Fig. 4b), namely, it blocked the Fe(III)CN reduction, the observation that DBMIB did not inhibit these photoactivities (Fig. 4c) implied that the first site to reduce Fe(III)CN along the electron transfer chain must be the PQ pool and/or the reduction of cyt b6f site (see Fig. 4a). Interestingly, the photocurrent increased in the presence of 5 μM DBMIB (Fig. 4c), indicating that electrons were extracted from PQ at a faster rate than from all the sites without the inhibitor, as reported elsewhere30,32.
Additional support to this conclusion was obtained by comparing the photoactivities of PSII particles prepared by the Berthold, Babcock and Yoccum (BBY) method (ref. 34) with those of crude thylakoids, see Fig. 4d. The photocurrent and H2O to Fe(III)CN electron transfer rate of the PSII particles were much lower than the respective values obtained with intact thylakoids (see Supplementary Fig. 3), despite the fact that PSII particles gave rise to higher specific activity when measured at a lower chlorophyll concentration than what was used here (see note in the legend of Fig. 4d). The PSII particles are enriched in PSII but contain less PQ and negligible amounts of cyt b6f and PSI34, compared with the thylakoids35. An additional explanation to the reduced photocurrent produced by the PSII particles as compared with that produced by intact thylakoids takes into account the reduced amount of PQ pool, which is about 3-fold lower in the PSII particles than in crude thylakoids35. The solution reduction potential is controlled by the concentrations of Fe(III)CN and Fe(II)CN, and is in equilibrium with the redox poise of the PQ pool, which is smaller and its turnover rate is slower in the PSII particles. Therefore, if PQ is reducing the exogenous Fe(III)CN, its reduced amount and turnover rate in the PSII particles results in a smaller photocurrent, as shown by the measurement of the H2O to Fe(III)CN electron transfer rate in Fig. 4d. Evidences for the beneficial contribution of PSI and cyt b6f complex to the photocurrent were reported by Calkins et al.16 and by Rasmussen and Minteer36 in similar systems. In the latter work, it was found that the dominant electron donor was PSI, followed by PSII and the cyt b6f complex36. In order to analyse whether or not Fe(III)CN is reduced by PSI in the present system, MV, which is a competitor to ferredoxin for accepting electrons from the Fa/Fb site of PSI16, was added to the system resulting with the reduction of the photocurrent by about 30% (see Supplementary Fig. 4). Altogether, the results in Fig. 4 show that the photocurrent was inhibited by DCMU but not by DBMIB, and that the PSII particles produced lower photocurrent than intact thylakoids, as well as the partial inhibition by MV, indicating that the mediator Fe(III)CN extracts photosynthetic electrons mostly from PQ, and possibly also from cyt b6f and PSI (to a lesser extent).
Further evidence to the involvement of photosynthesis in the photoactivity was obtained by analysing the spectral response of the photocurrent. We hypothesized that the photocurrent would be proportional to the light intensity absorbed by chlorophyll, the dominant pigment in plant thylakoids. Thus, we anticipated the maximal photocurrent to be obtained at wavelengths of 460 and 660 nm, where the light absorption of chlorophyll is maximal (see Supplementary Fig. 5). In order to examine this hypothesis, we measured the external quantum efficiency (EQE) spectrum using thylakoids in the amount equivalent to 100 μg Chl placed in the cell. The results are shown in Fig. 5, displaying two peaks at the same wavelengths as the peaks in the absorption spectrum of the spinach thylakoids (Supplementary Fig. 5). A maximum EQE of (17±4)% was obtained at 650–660 nm. A similar value was reported by Mersch et al.13, using mesoporous transparent electrodes with a much larger amount of PSII than we used here.
Low bias hydrogen generation
Photoelectrochemical water splitting has been proposed as a promising strategy for capturing and storing solar energy in the form of chemical energy, for example hydrogen fuel37. Towards this end, we sought the conditions in which the photocurrent could give rise to the reduction of protons in order to form H2 at the cathode. Thus, the anode and cathode were connected to the potentiostat in two-electrode mode of operation, and the photocurrent was measured as a function of the voltage between the two electrodes. In addition, the potential of the cathode was monitored simultaneously by measuring the voltage drop between the cathode and a reference electrode, as illustrated in Supplementary Fig. 6a. This enabled simultaneous measurement of the photocurrent as function of the applied voltage between the anode and cathode, as well as the potentials of the two electrodes. The results are shown in Fig. 6a. For hydrogen evolution, the cathode must be at a potential lower than 0 V with respect to the reversible hydrogen electrode (RHE) scale. This condition is reached at a minimum voltage of 0.8 V (see Fig. 6a), where the onset of the water photoelectrolysis reaction takes place. In a control experiment using the same setup without the thylakoids, a voltage of 2 V was required to initiate the water electrolysis reaction (see cyclic voltammogram in Supplementary Fig. 6b). Furthermore, in the experiment without the thylakoids the potential of the cathode was higher than 0 VRHE in the entire bias range of 0–1.5 V (see Supplementary Fig. 6c), indicating that no hydrogen evolution occurred in this range. Thus, the introduction of thylakoids to the BPEC cell reduced the minimum bias for the onset of the water splitting reaction from 2 to 0.8 V. The onset at 0.8 V is equal to the difference between the redox potential of the Fe(III) /Fe(II)CN redox couple and the hydrogen evolution reaction (HER) potential at a Pt electrode. This indicates that the light reactions split water and reduce Fe(III)CN, thus the Fe(III)/Fe(II)CN redox couple sets the anode potential, whereas the cathode potential reaches the HER potential at the onset of hydrogen evolution, giving rise to a bias of 0.8 V at the onset of water splitting with hydrogen evolution at the cathode. It is noteworthy that some photocurrent was measured below the onset of the water splitting reaction (see Fig. 6a). This photocurrent arose from other electrochemical side reactions, most likely the redox cycle of the Fe(III) /Fe(II)CN couple. The photocurrent associated with these processes saturated at ∼100 μA cm−2 at a bias of 0.5 V (see Fig. 6a). Between 0.5 and 0.8 V the photocurrent was constant, starting to increase again above 0.8 V and reaching ∼300 μA cm−2 at 1.4 V. Thus, the net water photoelectrolysis current density reached approximately 200 (=300–100) μA cm−2 at 1.4 V, indicating that the Faradaic efficiency for the water splitting reaction was ca. 67%.
In order to confirm this indirect estimation, the gases that evolved at the cathode headspace were collected and analysed by gas chromatography (GC). The H2 evolution rate at several time intervals during GC measurements at a bias of 0.6 or 1.0 V are presented in Fig. 6b. The H2 evolution rate between 5 and 15 min was found to be 3.4−3.5 μmol (mg Chl h)−1, being among the highest reported values for BPEC devices that operate without sacrificial electron donors. In control experiments, under a bias of 1 V and in the presence of 0.5 mM DCMU, or in the presence of Fe(III)CN but without thylakoids, H2 production could not be detected at all (Fig. 6b and Supplementary Fig. 6c), demonstrating that electron flow down-stream of PSII is crucial for H2 production. These observations are summarized in a schematic illustration of the proposed electron transfer pathways in the cell as depicted in Fig. 6c. Finally, the Faradaic efficiency (ηF) is calculated from the ratio between the slops of the H2 versus Q (Fig. 6d), indicating that the total charge that transfers between the working and counter electrodes produces hydrogen at a (69±3)% efficiency. This value is consistent with the dual electron pathway suggested in Fig. 6c, wherein 2/3 of the photocurrent supports proton reduction at the cathode, whereas the remaining 1/3 feeds the Fe(III)/Fe(II)CN electron transfer cycle.
Hybrid BPEC–PV tandem cell for solar water splitting
The photo-activated spinach thylakoids in the BPEC cell significantly reduced the voltage needed to produce H2 from water. Nonetheless, an external bias of at least 0.8 V was still needed to energize the process. Aiming to construct a stand-alone solar-powered device that does not require an external power source to operate, the BPEC cell was coupled in tandem with a Si PV cell (see photograph in Fig. 7a) that provides the bias needed for the water splitting reaction, as illustrated in Fig. 7b. This design mimics the Z-scheme in photosynthesis, wherein PSI reenergizes the electrons from PSII. In the BPEC–PV tandem cell, water oxidation is energized by the short wavelength radiation of the sunlight spectrum, harvested by the thylakoids. In addition, the long wavelength radiation transmitted through the thylakoids is captured by the PV cell, activating it to produce the power needed to support the overall water splitting reaction. In other words, the PV cell replaces the potentiostat that was used in the experiments described in the previous sections. Such a tandem design has two important merits in regards to solar water splitting. First, coupling the cells in series to increase the photovoltage produced by the device enables overall water splitting, which neither one of the cells could drive alone. Second, unlike a single absorber system, where only photons possessing sufficient energy to drive the water photolysis reaction are used to stimulate the PV cell, in the tandem cell less energy is needed from each photon. This allows a larger wavelength threshold (that is, more efficient light harvesting) and smaller thermalization loss, thereby increasing the power conversion efficiency of the system38,39. To evaluate the performance of the hybrid BPEC–PV tandem cell, the gases produced in the BPEC cell were analysed by GC (Fig. 7c). H2 gas formation was observed only in the presence of all the components, namely the electrolyte solution, thylakoids and PV cell. Maximal H2 production rate was obtained within the first 15 min of operation, after which the rate decreased and finally plateaued after 20 min. These observations are consistent with the results obtained for the BPEC cell alone (see inset of Fig. 2b and Fig. 6b). Expectedly, the addition of the herbicide DCMU totally inhibited the H2 evolution (see Fig. 7c).
Last, the effect of light intensity on the photocurrent produced by the BPEC–PV tandem cell was examined. The power output of the cell was calculated according to equation (2):
where ηF is the faradaic efficiency for the water splitting reaction (69%, see Fig. 6d), Jphoto is the photocurrent density and ΔG0 is the chemical potential of the water splitting reaction (1.23 V per electron in standard conditions). The maximal photocurrent density and power output of the cell were obtained under illumination of 80 mW cm−2 (see Fig. 7d), yielding Jphoto=300±25 μA cm−2 and Pout=250±20 μW cm−2. This corresponds to STH conversion efficiency, ηSTH=Pout/Pin where Pin is the power density of the incident light, of (0.31±0.03)%. It is noteworthy that the hybrid BPEC–PV tandem cell reached maximum performance at 80 mW cm−2, less than full 1 Sun conditions (100 mW cm−2). The decrease in photocurrent at light intensities above 80 mW cm−2 (see Fig. 7d) is most likely due to photo-saturation of the thylakoids at this light intensity threshold.
We presented here a BPEC cell comprising of plant thylakoids in electrolyte solution that produced photocurrents as high as 0.5 mA cm−2 derived from photosynthetically catalysed water oxidation. Powering the cell with additional bias greater than 0.8 V leads to overall water splitting with hydrogen and oxygen production at a Faradic efficiency of (69±3)%. A stand-alone tandem cell comprising the BPEC cell and a Si PV cell was demonstrated, reaching STH conversion efficiency of 0.3%. This innovative hybrid system brings together natural photosynthetic membranes and man-made PV technology in order to solve one of the greatest challenges in renewable energy development, that is solar energy conversion and storage in hydrogen fuel. Further development of this promising approach should aim to enhance the STH conversion efficiency, for example, by replacing flat transparent electrodes with porous ones.
Plant material and thylakoid membrane isolation
Spinach (Spinacia oleracea) grown in fields of the lower Galilee between the coordinates 33o4′18.4″N to 32o51′50.5″N and 35o16′32.8″E to 35o6′24.2″E was obtained from the local growers. The results presented in this work were obtained using three independent biological preparations. The thylakoid membranes preparation was carried out by grinding the young leaves in buffer A (50 mM 2-(N-morpholino)ethanesulfonic acid (MES)/NaOH pH=6.0, 15 mM NaCl, 5 mM MgCl, 2 mM CaCl2), and precipitating the thylakoids according to the procedure described by Andreasson et al.40 PSI I enriched membrane fragments (BBY membranes) were extracted using the detergent Triton X-100 (Sigma), as described by Berthold et al.34 The chlorophyll content in thylakoid preparations was determined according to the procedure described by Arnon41.
The photocurrent produced by the thylakoids was measured in the BPEC cell illustrated in Fig. 1a. The measurements were carried out at ambient temperature (25±2 °C). 0.1 mg Chl a of the thylakoids in buffer A solution containing 10% v/v glycerol were set on a FTO-coated glass electrode placed at the bottom of the BPEC cell. The BPEC cell was illuminated from the top by a solar simulator (Oriel Sol3A class AAA solar simulator, Newport, USA) calibrated to provide solar simulated (AM1.5G) light intensity of 1 Sun (100 mW cm−2) at the BPEC cell. The operating conditions were chosen based on a series of cyclic voltammetry measurements, and carried out using a potentiostat (Zennium, ZAHNER-elektrik, Germany) connected either in a three-electrode mode with an Ag/AgCl (in 3 M NaCl solution) reference electrode (RE-1B, CH Instruments, USA) and a platinum wire counter electrode, or in a two-electrode mode to a platinum wire counter electrode. Fe(III)CN mediated photocurrents were measured chrono-amperometrically at different potentials in buffer A solutions with different amounts of potassium ferricyanide (K3Fe(CN)6, Sigma Aldrich) as described in the text, under cyclic exposure to light–dark pulses. In order to examine the electron source, the herbicides DCMU (Fluka) and DBMIB (Aldrich) were used. The photocurrent density was calculated as the quotient of the current under illumination minus the dark current, divided by the projected area of the electrode (1.08 cm2) that was exposed to the light and in direct contact with the solution containing the thylakoids (Fig. 1a). The standalone solar water splitting tests were carried out by coupling the BPEC cell in tandem with a Si PV module (IXOLAR XOB17-04x3 SolarBit, IXYS, Korea). The photocurrent between the working (TEC15) and counter (Pt wire) electrodes and the voltage drop between the working and reference (Ag/AgCl) electrodes were monitored by digital multimeters (34401A DMM, Agilent Technologies, USA) and recorded digitally using LabVIEW (National Instruments, USA).
Quantum efficiency measurements
The EQE of the BPEC cell with 0.1 mg Chl and 3 mM Fe(III)CN was measured at a potential of 0.5 VAg/AgCl. The thylakoids were illuminated by monochromatic light obtained by coupling a white light source to a monochromator (Cornerstone CS260, Newport, USA) with a spectral band width of 10 nm. Fresh thylakoid membranes were used in each measurement, and the maximum photocurrent was recorded. This was repeated at different wavelengths, three times for each wavelength. The photon flux was obtained from the light intensity measured by a power meter (918D High Performance Photodiode Sensor, Newport, USA), and the EQE was calculated according to equation (3):
where q is the electron charge.
Photoinhibition experiments were done in the BPEC cell described above and with the same conditions as the photocurrent and hydrogen evolution measurements. Membranes were collected from the cell after 10 min incubation in the different conditions: dark/light, ±Fe(III)CN or ±Fe(II)CN. The thylakoids were re-suspended in fresh buffer to wash out the Fe(III)CN. Ten percent of the sample was taken for the measurement of the photosynthetic electron flow by spectroscopic analysis of the rate of DCMU and light dependent reduction of DCPIP (Sigma) serving as an indicator for oxygen production42, and the remaining 90% was used for photocurrent measurements. The photocurrent was measured using three electrode mode voltammetry (Ivium-n-Stat multichannel potentiostat, Ivium Technologies, The Netherlands) in fresh medium (buffer A, 3 mM Fe(III)CN, 0.09 mg Chl) under solar simulated illumination (model 10500 solar simulator, ABET Technologies, USA). DCPIP reduction was measured in 1 ml cuvette containing: buffer A, 50 μM DCPIP, thylakoids (10 μg Chl). The sample was illuminated with a white light halogen projector (0.15SU lamp, MRC). The DCPIP concentration was measured every 20 s with a monochromatic illumination at 600 nm for 100 s (using CO8000 cell density meter, WPA Biowave). The DCPIP reduction and the photocurrent values were normalized to the values measured when the membranes were placed in the BPEC cell (without Fe(III)CN) and immediately removed, centrifuged, re-suspended and divided 10% to DCPIP and 90% to photocurrent measurements.
O2 evolution and consumption
For comparison with the photocurrent measurements the O2 evolution rate was measured in a Clark electrode (Hansatech Instruments, UK) with 0.1 mg Chl membranes and 3 mM Fe(III)CN as an electron acceptor. The sample was illuminated with a solar simulator (model 10500 solar simulator, ABET Technologies, USA) at 1 Sun for 10 min. For other measurements the O2 evolution rate was calculated for 0.1 mg Chl with 3 mM DCBQ, Fe(III)CN or 1,1′-dimethyl-4,4′-bipyridinium (MV, Aldrich) as electron acceptors with or without DCMU and DBMIB, under white light illumination (MRC). Reduced MV reduces the O2 and therefore it measures the consumption rate of O2.
H2 evolution quantification
The H2 evolved at the cathode was collected into a designated glass tube, which was perforated at the bottom to allow buffer transfer, and sealed at the top with a rubber septum. Samples were collected from the headspace of the cell using a gas-tight syringe, and analysed by GC (7890A GC, Agilent Technologies, USA). The Faradaic efficiency for H2 generation was calculated from the ratio between the amount of H2 generated in the cell (, number of H2 moles generated during time interval t) and the amount of charge () that was transferred between the working and counter electrodes during the same time interval (t) according to equation (4):
Data supporting the findings of this study are available within the article and its supplementary information file and from the corresponding author upon request.
How to cite this article: Pinhassi, R. I. et al. Hybrid bio-photo-electro-chemical cells for solar water splitting. Nat. Commun. 7:12552 doi: 10.1038/ncomms12552 (2016).
Barber, J & Tran, P. D. From natural to artificial photosynthesis. J. R. Soc. Interface 10, 20120984 (2013).
Cook, T. R. et al. Solar energy supply and storage for the legacy and nonlegacy worlds. Chem. Rev. 110, 6474–6502 (2010).
Lewis, N. S. & Nocera, D. G. Powering the planet: chemical challenges in solar energy utilization. Proc. Natl Acad. Sci. USA 103, 15729–15735 (2006).
British-Petroleum. Statistical review of world energy. Available at http://www.bp.com/en/global/corporate/energy-economics/statistical-review-of-world-energy.html (2015).
Zhu, X.- G., Long, S. P. & Ort, D. R. Improving photosynthetic efficiency for greater yield. Annu. Rev. Plant Biol. 61, 235–261 (2010).
Michel, H. The nonsense of biofuels. Angew. Chem. Int. Ed. 51, 2516–2518 (2012).
Azwar, M., Hussain, M. & Abdul-Wahab, A. Development of biohydrogen production by photobiological, fermentation and electrochemical processes: a review. Renew. Sust. Energ. Rev. 31, 158–173 (2014).
Lubner, C. E. et al. Solar hydrogen-producing bionanodevice outperforms natural photosynthesis. Proc. Natl Acad. Sci. USA 108, 20988–20991 (2011).
Utschig, L. M., Silver, S. C., Mulfort, K. L. & Tiede, D. M. Nature-driven photochemistry for catalytic solar hydrogen production: a photosystem I–transition metal catalyst hybrid. J. Am. Chem. Soc. 133, 16334–16337 (2011).
Krassen, H. et al. Photosynthetic hydrogen production by a hybrid complex of photosystem I and [NiFe]-hydrogenase. ACS Nano. 3, 4055–4061 (2009).
McCormick, A. J. et al. Hydrogen production through oxygenic photosynthesis using the cyanobacterium Synechocystis sp. PCC 6803 in a bio-photoelectrolysis cell (BPE) system. Energy Environ. Sci. 6, 2682–2690 (2013).
Wang, W., Chen, J., Li, C. & Tian, W. Achieving solar overall water splitting with hybrid photosystems of photosystem II and artificial photocatalysts. Nat. Commun. 5, 4647 (2014).
Mersch, D. et al. Wiring of photosystem II to hydrogenase for photoelectrochemical water splitting. J. Am. Chem. Soc. 137, 8541–8549 (2015).
Purcell, M., Carpentier, R., Bélanger, D. & Fortier, G. Immobilized plant thylakoid membranes as a biosensor for herbicides. Biotechnol. Tech. 4, 363–368 (1990).
Agostiano, A., Goetze, D. C. & Carpentier, R. Photoelectrochemistry of thylakoid and sub-thylakoid membrane preparations: cyclic voltammetry and action spectra. Electrochim. Acta 38, 757–762 (1993).
Calkins, J. O., Umasankar, Y., O'Neill, H. & Ramasamy, R. P. High photo-electrochemical activity of thylakoid–carbon nanotube composites for photosynthetic energy conversion. Energy Environ. Sci. 6, 1891–1900 (2013).
Pinhassi, R. I. et al. Photosynthetic membranes of synechocystis or plants convert sunlight to photocurrent through different pathways due to different architectures. PLoS ONE 10, e0122616 (2015).
Hasan, K. et al. Photoelectrochemical communication between thylakoid membranes and gold electrodes through different quinone derivatives. ChemElectroChem. 1, 131–139 (2014).
ArianitaáDewi, H. Investigation of electron transfer from isolated spinach thylakoids to indium tin oxide. RSC Advances 4, 48815–48820 (2014).
Lee, J. & Kim, S. Mediator-free solar energy conversion by the artificially installed thylakoid membrane on the functionalized electrode. Electrochem. Commun. 49, 55–59 (2014).
Larom, S. et al. The photosystem II D1-K238E mutation enhances electrical current production using cyanobacterial thylakoid membranes in a bio-photoelectrochemical cell. Photosynth. Res. 126, 161–169 (2015).
Hamidi, H. et al. photocurrent generation from thylakoid membranes on osmium‐redox‐polymer‐modified electrodes. ChemSusChem. 8, 990–993 (2015).
Das, R. et al. Integration of photosynthetic protein molecular complexes in solid-state electronic devices. Nano Lett. 4, 1079–1083 (2004).
Ravi, S. K. & Tan, S. C. Progress and perspectives in exploiting photosynthetic biomolecules for solar energy harnessing. Energy Environ. Sci. 8, 2551–2573 (2015).
Barr, R., Troxel, K. S. & Crane, F. L. EGTA, a calcium chelator, inhibits electron transport in photosystem II of spinach chloroplasts at two different sites. Biochem. Biophys. Res. Commun. 92, 206–212 (1980).
Brewer, J. M. & Jagendorf, A. T. Damage to spinach chloroplasts induced by dark preincubation with ferricyanide. Plant Physiol. 40, 303 (1965).
Kirilovsky, D., Rutherford, A. W. & Etienne, A. L. Influence of DCMU and ferricyanide on photodamage in photosystem II. Biochemistry 33, 3087–3095 (1994).
Macdowall, F. & Lumry, R. Mechanism of the photochemical activity of isolated chloroplasts: VII. Inactivation of a photoact by dilute ferricyanide ion. Plant Physiol. 50, 305–307 (1972).
Cady, C. W., Crabtree, R. H. & Brudvig, G. W. Functional models for the oxygen-evolving complex of photosystem II. Coord. Chem. Rev. 252, 444–455 (2008).
Trebst, A. Inhibitors in the functional dissection of the photosynthetic electron transport system. Photosynth. Res. 92, 217–224 (2007).
Melis, A. Functional properties of Photosystem II β in spinach chloroplasts. Biochim. Biophys. Acta Bioenergetics 808, 334–342 (1985).
Ouitrakul, R. & Izawa, S. Electron transport and photophosphorylation in chloroplasts as a function of the electron acceptor. II. Acceptor-specific inhibition by KCN. Biochim. Biophys. Acta Bioenergetics 305, 105–118 (1973).
Roberts, A. G., Bowman, M. K. & Kramer, D. M. The inhibitor DBMIB provides insight into the functional architecture of the Qo site in the cytochrome b 6 f complex. Biochemistry 43, 7707–7716 (2004).
Berthold, D. A., Babcock, G. T. & Yocum, C. F. A highly resolved, oxygen-evolving photosystem II preparation from spinach thylakoid membranes: EPR and electron-transport properties. FEBS Lett. 134, 231–234 (1981).
Kurreck, J., Seeliger, A., Reifarth, F., Karge, M. & Renger, G. Reconstitution of the endogenous plastoquinone pool in photosystem II (PS II) membrane fragments, inside-out-vesicles, and PS II core complexes from spinach. Biochemistry 34, 15721–15731 (1995).
Rasmussen, M. & Minteer, S. D. Investigating the mechanism of thylakoid direct electron transfer for photocurrent generation. Electrochim. Acta 126, 68–73 (2014).
Brillet, J. et al. Highly efficient water splitting by a dual-absorber tandem cell. Nat. Photonics 6, 824–828 (2012).
De Vos, A. Detailed balance limit of the efficiency of tandem solar cells. J. Phys. D: Appl. Phys. 13, 839 (1980).
Bolton, J. R., Strickler, S. J. & Connolly, J. S. Limiting and realizable efficiencies of solar photolysis of water. Nature 316, 495 (1985).
Andreasson, E., Svensson, P., Weibull, C. & Albertsson, P.-Å. Separation and characterization of stroma and grana membranes—evidence for heterogeneity in antenna size of both photosystem I and photosystem II. Biochim. Biophys. Acta Bioenergetics 936, 339–350 (1988).
Arnon, D. I. Copper enzymes in isolated chloroplasts. Polyphenoloxidase in Beta vulgaris. Plant Physiol. 24, 1–15 (1949).
West, J. & Hill, R. Carbon dioxide and the reduction of indophenol and ferricyanide by chloroplasts. Plant Physiol. 42, 819–826 (1967).
This work was funded by the I-CORE Program of the Planning and Budgeting Committee, the Israel Science Foundation (grant no. 152/11), a grant from the transformative program of the US-Israel Binational Science Foundation (BSF grant no. 2011556), and a grant from the Deutsche Forschungsgemeinschaft (DIP project LU315/17-1). The results reported in this work were obtained using central facilities at the Technion’s Photovoltaic Laboratory, supported by the Nancy & Stephen Grand Technion Energy Program (GTEP) and by the Russell Berrie Nanotechnology Institute (RBNI), and at the Technion’s Hydrogen Technologies Research Laboratory (HTRL), supported by the Adelis Foundation and by the Solar Fuels I-CORE. We thank Dr Anatoly Bekkerman and the Faculty of Chemistry technical team for constructing the photocell; Dr Guy Ankonina from the PV lab for assistance in design and execution of electrochemical tests; Dr Nurit Waldman and Dr Shany Hershkovitz from the hydrogen lab for assistance in quantification the hydrogen production. R.P., D.K. and G.Sa. are supported by fellowships of the Nancy & Stephen Grand Technion Energy Program (GTEP). R.P. and D.K. are supported by fellowships of the Israeli Ministry of Science, Technology and Space. G.Sa. is supported by a Schulich Graduate fellowship.
The authors declare no competing financial interests.
About this article
Cite this article
Pinhassi, R., Kallmann, D., Saper, G. et al. Hybrid bio-photo-electro-chemical cells for solar water splitting. Nat Commun 7, 12552 (2016). https://doi.org/10.1038/ncomms12552
This article is cited by
Linker-free chemical preparation of palladium nanoparticles on aluminum-doped zinc oxide electrodes for electrochemical water oxidation
Journal of Materials Science: Materials in Electronics (2022)
Nature Reviews Chemistry (2019)
Nature Communications (2019)
Facile Surface Engineering of Ag–In–Zn–S Quantum Dot Photocatalysts by Mixed-Ligand Passivation with Improved Charge Carrier Lifetime
Catalysis Letters (2019)
NPG Asia Materials (2018)