Organic–inorganic perovskites such as CH3NH3PbI3 are promising materials for a variety of optoelectronic applications, with certified power conversion efficiencies in solar cells already exceeding 21%. Nevertheless, state-of-the-art films still contain performance-limiting non-radiative recombination sites and exhibit a range of complex dynamic phenomena under illumination that remain poorly understood. Here we use a unique combination of confocal photoluminescence (PL) microscopy and chemical imaging to correlate the local changes in photophysics with composition in CH3NH3PbI3 films under illumination. We demonstrate that the photo-induced ‘brightening’ of the perovskite PL can be attributed to an order-of-magnitude reduction in trap state density. By imaging the same regions with time-of-flight secondary-ion-mass spectrometry, we correlate this photobrightening with a net migration of iodine. Our work provides visual evidence for photo-induced halide migration in triiodide perovskites and reveals the complex interplay between charge carrier populations, electronic traps and mobile halides that collectively impact optoelectronic performance.
Organic–inorganic metal halide perovskites such as CH3NH3PbI3 are generating a great deal of excitement for their potential applications in a variety of high-performance optoelectronic devices including solar cells, light-emitting diodes, photodetectors and lasers1,2. These applications are enabled by the favourable material properties of these perovskites, which include long charge carrier diffusion lengths3,4,5, high absorption coefficients with a sharp absorption edge6 and a remarkably high photoluminescence (PL) quantum efficiency7,8. This latter property is particularly important for approaching the highest photovoltaic device performances at the Shockley–Queisser limit, in which all non-radiative recombination is eliminated9. Nevertheless, we recently reported that the PL lifetimes and intensities vary substantially between different grains even in high-quality films10. These observations are consistent with the presence of trap states that act as non-radiative recombination sites and influence the recombination kinetics8,10,11,12,13. In addition, the bulk optoelectronic properties such as photoluminescence8,14, electroluminescence15,16 and photoconductivity17 have also been shown to rise slowly over time under illumination or current flow. These observations indicate that, despite their remarkable device efficiencies, the perovskite films are still far from optimized for stabilized optoelectronic device performance.
It has been suggested that ionic migration in these perovskite materials could impact optoelectronic performance and affect device operation16,18,19. A substantial amount of recent evidence indicates that the hysteresis effects in current–voltage measurements originate from a migration of mobile ionic species, where positive and/or negative ionic species migrate to opposite electrodes under an internal field and impact charge collection16,18,19,20,21,22,23. Recent poling experiments on architectures with contacts have revealed evidence for the movement of ions under applied fields24,25,26,27,28, which can sometimes lead to degradation24,26. However, there are no reports presenting visual evidence for ionic migration in perovskite films without contacts and the ensuing impact of migration on the optoelectronic properties is not well understood.
Here we use a combination of confocal fluorescence microscopy and chemical imaging through time-of-flight secondary-ion-mass spectrometry (ToF-SIMS) to study high-quality thin films of the neat perovskite CH3NH3PbI3 without any contacts. We show that the PL lifetime and intensity increase significantly over time under illumination, and that these changes correspond to an order-of-magnitude reduction in the bulk trap state density. On the microscale, we find that light-soaking preferentially brightens regions with higher trap state densities and also induces a redistribution in local emission intensities. We use ToF-SIMS depth profiling to show that the rises in PL correlate with a redistribution of iodine in the film, thereby providing strong evidence for a photo-induced halide migration effect. Our results highlight the interplay between free carriers, traps and halide migration and their collective impact on optoelectronic performance.
Bulk changes in photoluminescence under illumination
In Fig. 1a, we show bulk time-resolved PL decays of a neat CH3NH3PbI3 film prepared on glass and corresponding to excellent device performance29 (Supplementary Methods), and the time-integrated intensity in Fig. 1b, over a time period of 10 min under pulsed illumination in vacuo. Initially, the PL lifetime is very fast with a significant fraction of non-radiative decay. However, over a period of tens to hundreds of seconds under illumination, the lifetime and total intensity both increase and eventually stabilize after ∼10 min (refs 8, 14). These observations are consistent with a substantial reduction and stabilization of fast non-radiative decay pathways (herein termed ‘cleaning’), and correlate closely with the rise in open-circuit voltage, as we show in the inset of Fig. 1b. The extent of the PL enhancements is influenced by different atmospheres14,30,31, though the effects are still observed in extremely low oxygen level environments including in vacuo and nitrogen and also in films made using other fabrication routes (see Supplementary Fig. 1; Supplementary Note 1), suggesting that the general photo-induced rise behaviour is intrinsic to these polycrystalline films. We note that the PL spectrum shape and position appears unchanged (Supplementary Fig. 2; Supplementary Note 2), suggesting that we are monitoring the same emissive species over the course of the measurement. We also do not observe any significant changes in X-ray diffraction patterns of the films acquired while light soaking, indicating that the illumination is not inducing large changes in crystal structure or phase composition (Supplementary Fig. 3) (ref. 19).
We have recently developed a model that is able to describe the photoluminescence kinetics in perovskite films in the presence of NT electronic subgap trap states (Supplementary Fig. 4; Supplementary Note 3) (ref. 8). The fits from the model are shown with the grey lines in Fig. 1a, and the extracted trap densities are shown in Fig. 1b, exhibiting the derived inverse dependence with PL intensity (Supplementary Note 4). The initial trap density of the sample just after illumination (t=4 s) is ∼1.7 × 1017 cm−3 and this slowly reduces to eventually stabilize at ∼2.5 × 1016 cm−3 (t=862 s, total photon dose of 258 J cm−2). This order-of-magnitude reduction in trap density under illumination also translates to increased emission and device photovoltage. Importantly, the stabilized values (∼1016 cm−3) are still well above the trap densities reported for single crystals (∼1010 cm−3) (refs 32, 33), suggesting that the polycrystalline films still have significant scope for improvement and that light soaking alone may not close the gap in trap state density with their single crystal counterparts. To make the connection between the trap state density and slow photo-induced optoelectronic improvements explicit, we find that the time taken to reach stabilized emission for both cleaved and uncleaved surfaces of single crystal samples is greatly reduced (Supplementary Fig. 1). We note that these results agree with recent theoretical work investigating the effect of different densities of sub-gap states on the open-circuit voltage, where the authors found that the voltage is significantly reduced below its theoretical limit at trap densities of >1017 cm−3 but not significantly impacted at trap densities of ∼5 × 1015 cm−3 (ref. 34) These findings are also in agreement with recent reports showing a light-induced increase in electron diffusion length35 as well as a reduction in the surface potential barrier at the grain boundaries5.
We show the normalized integrated PL over time at different temperatures in Fig. 1c (see Supplementary Fig. 5, Supplementary Note 5 for decay curves and extracted trap densities at each temperature). At low temperature (190 K), stabilized emission is reached after 10,000 s (∼3,000 J cm−2), whereas at high temperature (340 K), the PL reaches a stable output after just ∼100 s (∼30 J cm−2). This compares with ∼1,000 s (∼300 J cm−2) at room temperature (295 K). We determine an activation energy for the process of Ea=0.19±0.05 eV using an Arrhenius fit to the rises in PL rates (Fig. 1c inset, see Supplementary Fig. 6, Supplementary Note 6). We also find that the time taken to reach stabilized emission varies dramatically with illumination intensity, with higher intensities leading to substantially faster rise times (Supplementary Fig. 7; Supplementary Note 7). The very slow time scales, strong dependencies on temperature and intensity, and an activation energy on the order of hundreds of milli-electronvolts are consistent with a photo-induced ion migration phenomenon18,19,36 and will be discussed further below (also see Supplementary Note 8).
Local changes in photoluminescence under illumination
We now investigate how microstructure impacts the PL rise behaviour by considering the correlated scanning electron microscopy (SEM) micrograph (Fig. 2a) and photoluminescence image shown in Fig. 2b. We observe a heterogeneous distribution of grains with median grain size of ∼0.76 μm (Supplementary Fig. 8; Supplementary Note 9), where some regions are particularly bright in emission, while other grains and grain boundaries are comparatively dark and correspond to higher trap state densities10. In Fig. 2c, we monitor the local emission of different spots over time under continuous-wave (CW) 532-nm illumination at an intensity equivalent to ∼3 suns (188 mW cm−2) with a waist (w) spot size of ∼500 nm. A bright spot (red triangle) starts at a comparatively high emission level but does not substantially increase over time (relative change by a factor of 1.4). In contrast, a dark spot (blue circle) rises in intensity by nearly an order of magnitude after ∼3 min of illumination (factor of 8.7 relative change). An intermediate spot (green square), also rises by a factor of ∼1.6 over the same period.
These results provide important insight into the bulk measurements presented earlier, which represent an average across the distribution of grains (w ∼17 μm). While the bulk PL increases over time under illumination, each individual grain shows dramatically varied rise time behaviour depending on the initial trap state density. Dark spots rise significantly but the relative change in bright spots is much less, and the net result is an increase in spatially averaged PL eventually reaching a stabilized bulk PL, with the enhancements closely following the spatial profile of the laser (Supplementary Fig. 9; Supplementary Note 10).
To investigate the transient behaviour of the perovskite active layer under solar conditions, we show a fluorescence image in Fig. 3a before exposing the entire film to full-simulated sunlight for 60 min (100 mW cm−2, AM 1.5). Following the light soak (yellow shaded area in Fig. 3f), we observe PL enhancements consistent with those reported in Fig. 2c, then we monitor the local retention by taking fluorescence images over extended time intervals (Fig. 3b–d; see Supplementary Fig. 10 for complete series, Supplementary Note 11), where the sample was kept in the dark in between imaging. In Fig. 3f we show the average PL relaxation dynamics of the dark, intermediate and bright regions of interest (ROIs) defined in Fig. 3e (Supplementary Fig. 10) as well as the average relaxation (dotted black trace) across the fluorescence image. The emission from the dark regions relax and eventually reach a stabilized emission after ∼9 h, maintaining a PL level ∼3 × higher than their initial value before illumination. In contrast, the emission from the bright regions relax and stabilize at a lower PL level (0.66) relative to their initial value. Although the emission from all regions generally improves while under illumination, these results suggest that the photo-induced cleaning is locally retained (when left in the dark) in dark regions but not in bright regions (Supplementary Figs 10 and 11; Supplementary Note 11). Importantly, the stabilized average PL intensity of the analysed area after ∼9 h is approximately the same as the average initial PL intensity before illumination (initial and final points of dotted black trace). These observations are consistent with a new equilibrium corresponding to a redistribution of emission intensities with improved grain-to-grain homogeneity, which is only reached after an extended illumination period and several hours in the dark (Supplementary Fig. 12).
Compositional changes after illumination
To ascertain whether the light-induced PL enhancements and redistributions can be directly related to compositional changes, we now investigate the changes in local composition due to illumination by performing ToF-SIMS depth profiling on photo-irradiated films. We first light-soaked a local dark spot for several minutes with pulsed excitation (1.2 kJ cm−2) and recorded the typical slow rises in emission (Fig. 4a). Previously, we have reported enhancements in solar cell performance metrics, namely the open- circuit voltage (Voc), under similar photon doses used for this experiment37. We then performed ToF-SIMS on this same film and report the summed iodide signal through a depth profile at the illuminated region in Fig. 4b. Figure 4c shows the iodide distribution across the line scan (blue arrow) from Fig. 4b, along with the measured laser profile (blue line). We see that the regions of highest illumination intensity corresponding to the spatial profile of the laser show depleted levels of iodide, while the immediately adjacent regions show an enrichment in iodide relative to the background iodide levels (ROI shown in Supplementary Fig. 13). These results suggest a lateral migration of iodine away from the illumination area, which can be attributed to iodine redistribution (Supplementary Fig. 13; Supplementary Note 12). The ToF-SIMS counts suggest that the relative changes in iodine-containing fragments are on the order of a few percent, and since we also observe local variations in other lower intensity fragments, we conclude that iodine migration alone does not encompass the complexity of this ionic redistribution effect (Supplementary Note 12).
To probe the extent of halide redistribution as a function of film depth, we illuminated two different regions, one with a photon dose of 1.2 kJ cm−2 (red circle) and another with 2.4 kJ cm−2 (green circle), as shown in Fig. 5a, and we show the iodide intensity map in Fig. 5b. We again observe the typical PL rises and an anti-correlation between the measured excitation laser beam spatial profile and the resulting iodide intensity (Supplementary Fig. 14). In Fig. 5c, we show ToF-SIMS depth profiling data for iodide. To highlight the differences relative to a control area, the data are displayed as the difference between the light-soaked regions (red and green lines) and the background iodide level from a region that had not been light-soaked (blue line). We also show the carrier generation profile through the film thickness as a guide to the eye. As seen in Fig. 5c, the iodide level is initially lower in the light-soaked areas in comparison with the background region, and this is particularly true for film depths corresponding to high carrier densities. Consistent with this observation, as the carrier generation profile decays through the film, the iodide level increases relative to the background level deeper in the film and at the substrate interface (Supplementary Fig. 14). We observe a greater fraction of iodide deeper in the film when exposed to a photon dose of 2.4 kJ cm−2 (green line) as compared with 1.2 kJ cm−2 (red line), suggesting that the magnitude of iodide displacement is dependent on photon dose. Figure 5d shows the depth profiles of regions adjacent to the illuminated areas (pink and gold lines), where the iodide content is higher in the bulk of the film as well as deeper in the film in comparison to the background profile. These data are consistent with iodine migration away from the illuminated region both laterally and vertically. We also observe similar effects in mixed halide (that is, CH3NH3PbI3-xBrx) films19 (Supplementary Fig. 15) and also from energy-dispersive X-ray spectroscopy (EDS) measurements (Supplementary Fig. 16; Supplementary Note 13).
Proposed mechanism of photobrightening
Our interpretation of these results is that the illumination induces a redistribution of iodide resulting in a photo-cleaned (brightened) region with net reduced trap densities. The redistribution in iodide intensities alone is larger than the changes in iodine concentration associated with trap annihilation (∼p.p.m.). Here we propose a mechanism in Fig. 6 that broadly describes our observations in this study, but it is likely that there are other complex mass transport mechanisms simultaneously occurring. On film formation, some regions contain larger densities of electronic traps, which could arise from iodine vacancies (undercoordinated lead sites, δ+) with associated interstitial iodide ions8,18,29,38,39,40, which are numerous at surfaces and grain boundaries (Fig. 6a) (refs 10, 41, 42). Under illumination, we create a relatively high density of photo-excited electrons and holes, which is highest at the surface and falls off exponentially through the film (Fig. 5c). Many of the photo-excited electrons will become trapped in the vacancies particularly near the surface (Fig. 6b) (refs 13, 29, 42). The trap filling would perturb the system and create electric fields that induce iodide migration and subsequent trap annihilation in several ways: (1) Coulombic repulsion between now-unscreened iodide ions, (2) Spatial charge separation arising from the surface-trapped electrons and diffused holes or (3) A change in band bending at the surface on illumination29. In all cases, this field-induced migration allows the large amount of mobile iodide to fill vacancies and therefore yield a net reduction in the density of vacancies and interstitials which could be responsible for the non-radiative recombination (Fig. 6c)39,40,43,44. By locally illuminating a region we observe both vertical and lateral migration away from the carrier generation profile (cf. Fig. 5). If the entire film is illuminated (cf. Fig. 3), we expect vertical migration to still be prevalent and annihilation of defects under the illumination spot, leading to a net brightening of all grains, but the lateral migration will be dominated by local iodide and (filled) defect density gradients which will vary within and between grains; thus, some regions will locally brighten more than others due to relatively greater excess iodine removal in those regions. At higher excitation intensity, the time to reach stabilized emission will be faster because more traps will be filled by photo-generated electrons, thereby producing a larger field to drive halide migration. Likewise, at higher temperature the ionic conductivity will increase and the system will again reach stabilized emission in a shorter time. In the dark, the photo-excitation profile is removed and some traps remain, which may allow some iodide ions to slowly migrate back laterally or vertically to establish a new equilibrium (Fig. 6d; cf. Fig. 3), thereby leading to a partial reversibility. However, new concentration gradients may appear over time as ions cluster or disperse, thus the dynamics may be much more complicated (Supplementary Fig. 11).
We believe that our mechanism is also consistent with the rapid photo-brightening in perovskite nanocrystals and nanocrystalline domains with few trap sites per crystal, as reported by Tian et al.43 and Tachikawa et al31. Here traps are efficiently filled and the gradient driving ion migration results in the rapid net removal of the few interstitial-vacancy pairs per crystal. The mechanism we propose here may not be able to explain all photo-brightening phenomena. For example, it has been recently shown that oxygen species could contribute to the photo-brightening process14,30. Tian et al.14 recently proposed a model for the photo-brightening in the presence of oxygen, where photo-generated charge carriers and oxygen-related species interact to deactivate the trapping defects. In their mechanism and in ours, the photo-brightening is limited by the interaction volume of photo-excited carriers in the film. We take means to minimize oxygen in our measurements presented here, suggesting that oxygen may not be essential in the process. Nevertheless, the competition between oxygen and iodine in both diffusion and ability to annihilate traps, and any possible synergy between the two, remains an ongoing question for the community.
Tian et al. and others also speculate that the photo-induced brightening could be related to ion migration14,19. Here we provide direct strong visual evidence of photo-induced halide redistribution effects. Hoke et al.19 used PL measurements to calculate a bulk activation energy of 0.27±0.06 eV for halide migration in mixed halide systems (CH3NH3PbI3−xBrx), which roughly agrees with the value we extract here of 0.19±0.05 eV for the pure trihalide systems (Fig. 1c). Indeed, activation energies for iodide migration in CH3NH3PbI3 have been recently estimated to be in the range ∼0.1–0.6 eV (refs 18, 36). The differences may in part be due to different local stoichiometry, that is, iodide-rich or iodide-poor conditions, which has a large influence on the formation energies of iodide interstitials39,45. For example, the formation energy of iodide interstitials in iodide-rich conditions is also ∼0.2 eV, suggesting that the activation energy we extract here could be related to the interstitial/vacancy-mediated transport of iodide18,36. The reversible ion redistribution could also be consistent with the photo-induced structural changes reported elsewhere46,47.
Finally, we discuss how these slow transient effects and our measurements are relevant to full optoelectronic devices. We have observed a light-induced halide migration in neat films, which we attribute to the formation of local fields created by filling traps under illumination. Others have reported methylammonium migration but only in full devices in the presence of a field across the entire film24,25,26. Since the migration in both cases likely arises from electric fields, we could use the light-induced changes as a proxy to learn about the field-induced changes in the full devices. For instance, the depth profile data (Fig. 5) revealed that just by illuminating with light, we can deplete iodine at the top surface and redistribute it to the substrate interface (that is, contact in a full device), which would strongly affect band bending and charge collection16. Furthermore, we learn that the ion migration in full devices is not simply due to defects moving under an applied field, rather there is a dynamic interplay between carriers, traps and mobile ions that needs to be considered. This has direct relevance to the hysteresis phenomena in full solar cells, which has been proposed to be primarily caused by ion migration16,21,23 but also necessitates the presence of trap states22. The rise times to stabilized efficiency at the maximum power point in full n-i-p solar cells closely match the time scales to reach stabilized emission due to photo-induced cleaning under 1-sun equivalent irradiation8,23, which is consistent with both phenomena arising from ion migration. Notably, we observe here that the halide migration is related to the passivation, or deactivation of traps, hence the hysteresis observed in solar cells could be amplified by the activation or deactivation of electron traps depending on whether the mobile iodine is pushed towards, or away from, the n-type charge collection layer. This is consistent with our recent work where we have reduced the perovskite trap density by an order of magnitude by treating the polycrystalline film surface with small molecules, such as pyridine, and we observe that the rise times to stabilized maximum power output are much faster and hysteresis is reduced40,48. In the extreme case of negligibly low trap densities as in single crystals, we show that the emission stabilizes rapidly (see Supplementary Fig. 1), and this is consistent with the minimal hysteresis effects reported for devices comprising single crystals or millimetre-scale grain thin films32,33,49. We can conclude that the rise times to stabilized maximum power are much faster for solar cells incorporating perovskites with lower trap densities, and a lack of transient behaviour strongly suggests that ion migration has been suppressed. It is therefore imperative to reduce the trap density to eliminate unwanted ion migration effects, and future work should concentrate on fabricating perovskites with uniform iodine distributions and low trap densities (by improving growth processes or post-treating samples) to achieve instantaneously stabilized optoelectronic behaviour. It still remains unclear if we require films with a stoichiometric composition, or if in fact halide-deficient regions are more PL active39. The finding that potentially large fractions of iodine are moving under illumination without major changes to crystal structure (cf. X-ray diffraction measurements, Supplementary Fig. 3) needs to be understood and remains an open question for the community.
In conclusion, we have investigated CH3NH3PbI3 films without contacts and find that the PL lifetime and PL intensity rise substantially over time under illumination corresponding to nearly an order-of-magnitude reduction in trap densities. On the microscale, we find that the changes in PL and trap density are particularly significant for the dimmer spots. There is a strong correlation between the increase in PL over time under illumination and a redistribution of iodine away from the illuminated region, where this redistribution is likely connected to the redistribution of stabilized PL intensities. These results are consistent with a photo-induced iodide migration with an activation energy of 0.19±0.05 eV. This work gives direct visualization of photo-induced halide migration in the neat perovskite materials that is related to slow transient optoelectronic phenomena and lowering of the trap densities through ‘cleaning’ effects; the precise mechanism of migration and significance of the activation energy remains an open question for the community. The correlations between local photophysical behaviour and local composition profiled through the film presented in this work will provide an excellent tool set to further understand the impact of chemical-, photo-, field- and atmospheric-induced effects on these slow transients and ion migration in operating devices.
Perovskites were prepared using a method described elsewhere where a methylammonium iodide (CH3NH3I) and lead acetate Pb(Ac)2·3H2O precursor mixture was employed29. To generate the perovskite solution, CH3NH3I (Dyesol) and Pb(Ac)2·3H2O were dissolved in anhydrous N,N-dimethylformamide at a 3:1 molar ratio with final concentration of ∼30 wt%, and the stabilizer hypophosphorous acid (HPA) was added at a molar ratio of 7.5% with respect to Pb(Ac)2·3H2O. Pb(Ac)2·3H2O (316512) and HPA (214906) were purchased from Sigma Aldrich. Microscope slides and coverslips were washed sequentially with soap (2% vol. Hellmanex in water), de-ionized water, isopropanol, acetone and finally treated under oxygen plasma for 10 min. The precursor solution was spin-coated at 2,000 r.p.m. for 45 s in a nitrogen-filled glovebox, and the substrates were then dried at room temperature for 10 min before annealing at 100 °C for 5 min. The samples were then stored in a nitrogen-filled glovebox until used.
Bulk time-resolved PL (TRPL) decays were acquired using a time-correlated single photon counting (TCSPC) setup (FluoTime 300, PicoQuant GmbH). Temperature-dependent measurements were carried out in vacuo using an Oxford Instruments OptistatDN cryostat with a specialized fitting for the TCSPC set-up. Samples were photoexcited using a 507-nm laser head (LDH-P-C-510, PicoQuant GmbH) with pulse duration of 117 ps, fluences of ∼0.03–3 μJ cm−2 per pulse, and a repetition rate of 1 MHz. To acquire PL decays over time under illumination, integration times were kept short (2–10 s). The stated times in the legends are time stamps at the end of each integration window for each curve.
Confocal fluorescence imaging
Optical microscopy and spectroscopy were performed under nitrogen (flow cell) using a custom sample scanning confocal microscope with TCSPC (PicoHarp 300) capabilities built around a Nikon TE-2000 inverted microscope fitted with an infinity corrected × 50 dry objective (Nikon L Plan, NA 0.7, CC 0–1.2). A 470-nm pulsed diode laser (PDL-800 LDH-P-C-470B, 350 ps pulse width) was used for excitation with a repetition rate of 1 MHz for time-resolved PL measurements and 40 MHz for collecting fluorescence images. A 532-nm CW laser (CrystaLaser, GCL532-005-L) was used to excite local regions and monitor the PL rises over time. Samples were excited face-on through the flow cell’s coverslip and the emission was filtered through a 700-nm longpass filter then directed to a Micro Photon Devices (MPD) PDM Series single photon avalanche photodiode with a 50-μm active area. The sample stage was controlled using a piezo controller (Physik Instrumente E-710) with custom software. For collecting fluorescence images, the pixel size was 100 nm with a short pixel dwell time (integration time) of 50 ms, to minimize the extent of photoinduced cleaning prior to collecting longer exposure local measurements. For wide area light-soaking experiments, the entire film was exposed to AM 1.5 G light illumination from a solar simulator (Solar Light Co. model 16S-300) with intensity calibrated to 100 mW cm−2 using a Si reference cell and source meter (Keithley, 2400 Series). Before collecting fluorescence images, the system was calibrated using 200 nm fluorescent microspheres (Life Technologies FluoSpheres Polystyrene Microspheres, 200 nm, red fluorescent, 580/605) to yield a point-spread function of ∼350 nm at full width at half maximum. To correlate fluorescence images with SEM micrographs and ToF-SIMS, we made fiducial markers on the sample and used these markers along with local microstructure to match areas across the separate measurements.
Scanning electron microscopy
SEM images were taken using a FEI Sirion SEM at 5–10 kV accelerating voltage. To prevent charging effects, samples for SEM were imaged after sputtering ∼7 nm of Au/Pd using a SPI-Module Sputter Coater with argon flow.
Time-of-flight secondary-ion-mass spectrometry
ToF-SIMS depth profiles were carried out using an IonToF ToF-SIMS 5 instrument. Dual-beam depth profiles were acquired using a 25-keV Bi3+ ion source in delayed extraction mode for images and a 20-keV argon 1000 gas cluster ion source for sputtering. Sputtering was carried out over a 600 micron × 600 micron area at 3.3 nA current for 2 s for a dose of 1.1 × 1013 ions cm−2 per sputter cycle. Images were acquired over a 50 micron × 50 micron area within the centre of the sputter crater with a current of ∼0.03 pA for a dose per cycle of 5.7 × 1011 ions cm−2. Secondary ions were detected using a time-of-flight mass analyzer. Due to non-linearity in the mass axis introduced when using delayed extraction50, peak identities were determined from spectra acquired using the standard spectroscopy mode of the IonToF instrument using similar settings as described above. The negative ion spectra were calibrated using the CH−, OH− and I− peaks. Calibration errors were kept below 30 p.p.m. Mass resolution (m/Δm) for a typical spectrum was between 4,000 and 6,000 for m/z 25.
The data that support the findings of this study are available from the corresponding author upon request.
How to cite this article: deQuilettes, D. W. et al. Photo-induced halide redistribution in organic–inorganic perovskite films. Nat. Commun. 7:11683 doi: 10.1038/ncomms11683 (2016).
Stranks, S. D. & Snaith, H. J. Metal-halide perovskites for photovoltaic and light-emitting devices. Nat. Nanotechnol. 10, 391–402 (2015).
Johnston, M. B. Optoelectronics: colour-selective photodiodes. Nat. Photon. 9, 634–636 (2015).
Stranks, S. D. et al. Electron-hole diffusion lengths exceeding 1 micrometer in an organometal trihalide perovskite absorber. Science 342, 341–344 (2013).
Xing, G. et al. Long-range balanced electron- and hole-transport lengths in organic-inorganic CH3NH3PbI3. Science 342, 344–347 (2013).
Edri, E. et al. Why lead methylammonium tri-iodide perovskite-based solar cells require a mesoporous electron transporting scaffold (but not necessarily a hole conductor). Nano. Lett. 14, 1000–1004 (2014).
De Wolf, S. et al. Organometallic halide perovskites: sharp optical absorption edge and its relation to photovoltaic performance. J. Phys. Chem. Lett. 5, 1035–1039 (2014).
Deschler, F. et al. High photoluminescence efficiency and optically pumped lasing in solution-processed mixed halide perovskite semiconductors. J. Phys. Chem. Lett. 5, 1421–1426 (2014).
Stranks, S. D. et al. Recombination kinetics in organic-inorganic perovskites: excitons, free charge, and subgap states. Phys. Rev. Appl. 2, 034007 (2014).
Miller, O. D., Yablonovitch, E. & Kurtz, S. R. Strong internal and external luminescence as solar cells approach the Shockley-Queisser limit. IEEE Journal of Photovolt. 2, 303–311 (2012).
deQuilettes, D. W. et al. Impact of microstructure on local carrier lifetime in perovskite solar cells. Science 348, 683–686 (2015).
Wetzelaer, G. J. et al. Trap-assisted non-radiative recombination in organic-inorganic perovskite solar cells. Adv. Mater. 27, 1837–1841 (2015).
Yamada, Y., Nakamura, T., Endo, M., Wakamiya, A. & Kanemitsu, Y. Photocarrier recombination dynamics in perovskite CH3NH3PbI3 for solar cell applications. J. Am. Chem. Soc. 136, 11610–11613 (2014).
Leijtens, T. et al. Electronic properties of meso-superstructured and planar organometal halide perovskite films: charge trapping, photodoping, and carrier mobility. ACS Nano 8, 7147–7155 (2014).
Tian, Y. et al. Mechanistic insights into perovskite photoluminescence enhancement: light curing with oxygen can boost yield thousandfold. Phys. Chem. Chem. Phys. 17, 24978–24987 (2015).
Wojciechowski, K. et al. Heterojunction modification for highly efficient organic-inorganic perovskite solar cells. ACS Nano 8, 12701–12709 (2014).
Tress, W. et al. Understanding the rate-dependent J–V hysteresis, slow time component, and aging in CH3NH3PbI3 perovskite solar cells: the role of a compensated electric field. Energy Environ. Sci. 8, 995–1004 (2015).
Gottesman, R. et al. Extremely Slow Photoconductivity Response of CH3NH3PbI3 Perovskites Suggesting Structural Changes under Working Conditions. J. Phys. Chem. Lett. 5, 2662–2669 (2014).
Eames, C. et al. Ionic transport in hybrid lead iodide perovskite solar cells. Nat. Commun. 6, 7497 (2015).
Hoke, E. T. et al. Reversible photo-induced trap formation in mixed-halide hybrid perovskites for photovoltaics. Chem. Sci. 6, 613–617 (2015).
Unger, E. L. et al. Hysteresis and transient behavior in current-voltage measurements of hybrid-perovskite absorber solar cells. Energy Environ. Sci. 7, 3690–3698 (2014).
Zhang, Y. et al. Charge selective contacts, mobile ions and anomalous hysteresis in organic-inorganic perovskite solar cells. Mater. Horiz. 2, 315–322 (2015).
van Reenen, S., Kemerink, M. & Snaith, H. J. Modeling anomalous hysteresis in perovskite solar cells. J. Phys. Chem. Lett. 6, 3808–3814 (2015).
Snaith, H. J. et al. Anomalous hysteresis in perovskite solar cells. J. Phys. Chem. Lett. 5, 1511–1515 (2014).
Leijtens, T. et al. Mapping electric field–induced switchable poling and structural degradation in hybrid lead halide perovskite thin films. Adv. Energy Mater 5, 1500962 (2015).
Yuan, Y. B. et al. Photovoltaic switching mechanism in lateral structure hybrid perovskite solar cells. Adv. Energy Mater. 5, 1500615 (2015).
Xiao, Z. et al. Giant switchable photovoltaic effect in organometal trihalide perovskite devices. Nat. Mater. 14, 193–198 (2015).
Deng, Y., Xiao, Z. & Huang, J. Light-induced self-poling effect on organometal trihalide perovskite solar cells for increased device efficiency and stability. Adv. Energy Mater 5, 1500721 (2015).
Yang, T. Y., Gregori, G., Pellet, N., Gratzel, M. & Maier, J. The significance of ion conduction in a hybrid organic-inorganic lead-iodide-based perovskite photosensitizer. Angew. Chem. Int. Ed. 54, 7905–7910 (2015).
Zhang, W. et al. Enhanced optoelectronic quality of perovskite thin films with hypophosphorous acid for planar heterojunction solar cells. Nat. Commun. 6, 10030 (2015).
Galisteo-López, J. F., Anaya, M., Calvo, M. E. & Míguez, H. Environmental effects on the photophysics of organic–inorganic halide perovskites. J. Phys. Chem. Lett. 6, 2200–2205 (2015).
Tachikawa, T., Karimata, I. & Kobori, Y. Surface charge trapping in organolead halide perovskites explored by single-particle photoluminescence imaging. J. Phys. Chem. Lett. 6, 3195–3201 (2015).
Dong, Q. et al. Electron-hole diffusion lengths>175 mum in solution-grown CH3NH3PbI3 single crystals. Science 347, 967–970 (2015).
Shi, D. et al. Low trap-state density and long carrier diffusion in organolead trihalide perovskite single crystals. Science 347, 519–522 (2015).
Yang, W., Yao, Y. & Wu, C.-Q. Origin of the high open circuit voltage in planar heterojunction perovskite solar cells: role of the reduced bimolecular recombination. J. Appl. Phys. 117, 095502 (2015).
Kedem, N. et al. Light-induced increase of electron diffusion length in a p–n junction type CH3NH3PbBr3 perovskite solar cell. J. Phys. Chem. Lett. 6, 2469–2476 (2015).
Azpiroz, J. M., Mosconi, E., Bisquert, J. & De Angelis, F. Defect migration in methylammonium lead iodide and its role in perovskite solar cell operation. Energy Environ. Sci. 8, 2118–2127 (2015).
Matsumoto, F., Vorpahl, S. M., Banks, J. Q., Sengupta, E. & Ginger, D. S. Photodecomposition and morphology evolution of organometal halide perovskite solar cells. J. Phys. Chem. C 119, 20810–20816 (2015).
Walsh, A., Scanlon, D. O., Chen, S., Gong, X. G. & Wei, S. H. Self-regulation mechanism for charged point defects in hybrid halide perovskites. Angew. Chem. Int. Ed. Engl. 54, 1791–1794 (2015).
Buin, A. et al. Materials processing routes to trap-free halide perovskites. Nano. Lett. 14, 6281–6286 (2014).
Noel, N. K. et al. Enhanced photoluminescence and solar cell performance via lewis base passivation of organic-inorganic lead halide perovskites. ACS Nano 8, 9815–9821 (2014).
Verwey, J. F. Time and intensity dependence of the photolysis of lead halides. J. Phys. Chem. Solids 31, 163–168 (1970).
Bischak, C. G., Sanehira, E. M., Precht, J. T., Luther, J. M. & Ginsberg, N. S. Heterogeneous charge carrier dynamics in organic-inorganic hybrid materials: nanoscale lateral and depth-dependent variation of recombination rates in methylammonium lead halide perovskite thin films. Nano Lett. 15, 4799–4807 (2015).
Tian, Y. et al. Enhanced organo-metal halide perovskite photoluminescence from nanosized defect-free crystallites and emitting sites. J. Phys. Chem. Lett. 6, 4171–4177 (2015).
Du, M.-H. Density functional calculations of native defects in CH3NH3PbI3: effects of spin–orbit coupling and self-interaction error. J. Phys. Chem. Lett. 6, 1461–1466 (2015).
Yin, W.-J., Shi, T. & Yan, Y. Unusual defect physics in CH3NH3PbI3 perovskite solar cell absorber. Appl. Phys. Lett. 104, 063903 (2014).
Juarez-Perez, E. J. et al. Photoinduced giant dielectric constant in lead halide perovskite solar cells. J. Phys. Chem. Lett. 5, 2390–2394 (2014).
Gottesman, R. et al. Photoinduced reversible structural transformations in free-standing CH3NH3PbI3 perovskite films. J. Phys. Chem. Lett. 6, 2332–2338 (2015).
Nagaoka, H. et al. Zr incorporation into TiO2 electrodes reduces hysteresis and improves performance in hybrid perovskite solar cells while increasing carrier lifetimes. J. Phys. Chem. Lett. 6, 669–675 (2015).
Nie, W. et al. High-efficiency solution-processed perovskite solar cells with millimeter-scale grains. Science 347, 522–525 (2015).
Vanbellingen, Q. P. et al. Time-of-flight secondary ion mass spectrometry imaging of biological samples with delayed extraction for high mass and high spatial resolutions. Rapid Commun. Mass Spectrom. 29, 1187–1195 (2015).
The research leading to these results has received funding from the European Union Seventh Framework Programme (FP7/2007–2013) under grant agreement 604032 of the MESO project, and also from the People Programme (Marie Curie Actions) of the European Union’s Seventh Framework Programme (FP7/2007–2013) under REA grant agreement number PIOF-GA-2013-622630. D.W.D. and D.S.G. acknowledge DOE (DE-SC0013957) for supporting the local imaging work. D.W.D. acknowledges support from an NSF Graduate Research Fellowship (DGE-1256082) and thanks M. Ziffer and J. Mohammed for providing single crystal samples. S.D.S. also thanks R.H. Friend for additional support and R. Brenes for additional PL measurements. W.Z. thanks the EPSRC Supergen Supersolar project for financial support. This research was performed in part at the Molecular Analysis Facility (MAF) which is funded, in part, by the University of Washington, Molecular Engineering and Sciences Institute, and the Clean Energy Institute, as well as infrastructure grants from the National Institutes of Health (NIH) and the National Science Foundation. The argon cluster source used in this research was funded by NIH grant S10 OD010607. V.B. was supported as part of the Center for Excitonics, an Energy Frontier Research Center funded by the U.S. Department of Energy, Office of Science, Office of Basic Energy Sciences under Award Number DE-SC0001088 (MIT). The authors thank MIT Libraries for contributions to open access article processing fees.
The authors declare no competing financial interests.
About this article
Cite this article
deQuilettes, D., Zhang, W., Burlakov, V. et al. Photo-induced halide redistribution in organic–inorganic perovskite films. Nat Commun 7, 11683 (2016). https://doi.org/10.1038/ncomms11683
Nature Reviews Materials (2021)
Study of performance and stability of hole transport layer-free perovskite solar cells with modified electron transport layer
Journal of Materials Science: Materials in Electronics (2021)
Nano Research (2021)
Communications Physics (2020)
Nature Communications (2020)