In this work, we propose a novel approach for wafer-scale integration of 2D materials on CMOS photonic chip utilising methods of synthetic chemistry and microfluidics technology. We have successfully demonstrated that this approach can be used for integration of any fluid-dispersed 2D nano-objects on silicon-on-insulator photonics platform. We demonstrate for the first time that the design of an optofluidic waveguide system can be optimised to enable simultaneous in-situ Raman spectroscopy monitoring of 2D dispersed flakes during the device operation. Moreover, for the first time, we have successfully demonstrated the possibility of label-free 2D flake detection via selective enhancement of the Stokes Raman signal at specific wavelengths. We discovered an ultra-high signal sensitivity to the xyz alignment of 2D flakes within the optofluidic waveguide. This in turn enables precise in-situ alignment detection, for the first practicable realisation of 3D photonic microstructure shaping based on 2D-fluid composites and CMOS photonics platform, while also representing a useful technological tool for the control of liquid phase deposition of 2D materials.
The recent development of nanocomposites consisting of fluid-dispersed atomically thin two-dimensional (2D) materials has sparked a great level of interest as a highly promising in-situ tailored meta-material device platform for the next generation of multi-functional optoelectronic systems1,2,3,4,5,6,7,8,9,10,11,12,13. Dynamically controlled three-dimensional (3D) self-assembly of fluid-suspended 2D materials not only provides a new breakthrough route for technological applications of 2D material based 3D device architectures14,15,16, but also their fluidic nature allows CMOS-compatible wafer-scale back-end integration on chip using microfluidic technology17,18,19. The practical realisation of dynamically reconfigurable 3D material fluid metastructures integrated into a microfluidic system and coupled with a CMOS photonic circuit (as illustrated in Fig. 1) opens up limitless possibilities in the fabrication of compact and low-power systems for commercially viable, miniaturised, multi-functional light-management devices such as light emitting sources20, tuneable optical filters21 and nanoantenna phased arrays22. For example, 1D photonic crystals of graphene which could act as optical filters have been theoretically explored23 but as yet no method exists for the precise reconfigurable control of such structures. Additionally, self-assembly of fluid dispersed 2D materials represents a remarkable precursor state for liquid phase deposition of ordered lamellae, stacks and other structures in the solid phase24,25,26. Reconfigurability of the metastructures can be achieved by exploiting liquid crystal technology6,15 with in-situ monitoring used to characterise the metastructure formation.
However, the primary challenge for the first realisation of on-chip controlled assembly of 2D flakes into functional metastructures is the lack of a reliable and sensitive method for in-situ characterisation. Such a method is pivotal to the confirmation of the integration of composites in the device and to enable determination of parameters, such as spatial alignment of incorporated 2D materials, dynamically during device operation. Conventional characterisation methods such as Raman spectroscopy5,27,28, coherent anti-Stokes Raman spectroscopy (CARS)29 and Fourier Transform Infrared Spectroscopy (FTIR)30 are not suitable for studies of fluid nanocomposites with relatively low concentrations of nanoparticles dispersed. In this case, the significantly greater scattering volume of the host fluid compared to that of the dispersed nanoparticles always dominates the vibrational signal intensity, rendering the monitoring of the considerably weaker bands of dispersed nanoparticles impossible.
Here we demonstrate, for the first time, the wafer-scale integration of fluid-dispersed 2D materials on Si photonic chip utilising microfluidic technology, and their subsequent electrical and optical manipulation. We also propose and subsequently demonstrate a novel approach for ultra-sensitive, label-free, in-situ detection and monitoring of integrated 2D-fluid composite materials on-chip. Specifically, we propose an in-situ micro-Raman characterisation approach, whereby the Raman signal of 2D dispersed nanoparticles is selectively enhanced through the design of optofluidic waveguide geometry on silicon-on-insulator (SOI) platform. It has previously been shown that the Raman signal from micro-structured silicon cavities can be enhanced due to Fabry-Pérot type resonances31,32,33. Here, the structure is designed to simultaneously enhance different resonant modes relating to different parameters of the optofluidic waveguides, balancing the required enhancement of the signal from multiple vibrational bands with the desire for the greatest achievable intensity for the individual bands. The developed approach demonstrates ultra-high sensitivity to the xyz alignment of 2D nanoparticles within optofluidic waveguides. Hence, for the first time, our findings demonstrate the possibility of monitoring the dynamics of fluid-dispersed 2D nanoparticles on chip. Our work paves the way for the practical realisation of dynamically reconfigurable photonic metastructures based on 2D-fluid composites integrated on CMOS photonics platform with a range of important applications, such as renewable energy, optical communications, bio-chemical sensing, and security and defence technologies4,8,34 or as a precursor to controlled deposition of solid state structures24,25,26.
Typically, large-scale CMOS photonics builds on a SOI platform; a high index-contrast waveguide platform which prevents interference between the photonic integrated circuit components and the substrate. Therefore, we use an SOI based Fabry-Pérot type optofluidic waveguide channel, with an open top cladding (Fig. 1 inset) to allow in-situ micro-Raman detection and monitoring of the integrated 2D fluid nanocomposite system during device operation. To optimise the optofluidic waveguide design for facilitating strong confinement of light on chip and to significantly enhance the Raman back-scattered signal of the individual incorporated 2D nanoplatelets, we model the variation in the intensity of the Raman bands of dispersed nanoparticles while varying parameters that can be experimentally controlled, such as: the waveguide width, w, and the buffer oxide (BOX) layer thickness, hBOX. We consider the specific case of the D and G bands of 2D carbon-based materials (Fig. 2)- such as graphene and graphene oxide (GO)- dispersed in a nematic liquid crystal (LC) host, however the proposed methodology can be utilised for any fluid-dispersed material. The backscattered Raman signal intensity is numerically determined for wavelengths corresponding to the Raman active bands using the scattering matrix method [See Supplementary Methods]. The complex variation of the Raman signal as a result of modifying the optofluidic waveguide parameters can be rationalised as the superposition of Fabry-Pérot resonance effects in different parts of the geometry. Enhancement of up to 100x can be observed between maximising and minimising combinations of the optofluidic waveguide parameters.
In order to experimentally demonstrate the enhancement of the Raman intensity, 2D material-fluid nanocomposites, consisting of graphene and GO nanoplatelets dispersed in LCs, were prepared by a liquid phase dispersion method [See Supplementary Methods]. The optimal parameters for the microfluidic structures were determined from the calculated Raman signal intensity maps shown in Fig. 2. Resonator devices consisting of optofluidic waveguide channels of different widths were fabricated on SOI wafer with a thick buffer oxide (hBOX = 2 μm) layer and with a silicon device layer of 15 μm. The prepared nanocomposites were integrated into optofluidic waveguide channels via infiltration reservoirs on the chip (Fig. 3). The selected microfluidic channels had widths in the ranges 3.7 ± 0.2 μm (narrow channels, strong enhancement) and 10.5 ± 1.5 μm (wide channels, weaker enhancement). Optical microscopy (Fig. 3b) and scanning electron microscopy (Fig. 3c–e) both confirmed the successful integration of the nanocomposite into all channels.
Raman spectra are presented for the GO-LC nanocomposites- with MLC-6608 (Fig. 4a) and with E7 (Fig. 4b) as the fluid host-measured in-situ at three points on the chip; more specifically: in a wide channel (Fig. 4c), in a narrow channel (Fig. 4d) and in an infiltration reservoir (Fig. 4e). Liquid crystal MLC-6608 exhibits weak Raman bands (see Supplementary Results) that have no strong overlap with the D and G bands, allowing for clear determination of the GO bands in gathered spectra. Raman spectra were recorded for individual monolayer flakes of area 1.0 ± 0.1 μm2 in all cases. For GO dispersed in MLC-6608, the D band Raman intensities were observed in the approximate ratio 5:8:16 for an infiltration reservoir, 11.6 μm channel and 3.6 μm channel respectively. For the G band, intensities were observed in the ratio 5:7:16. E7, however, has a strong Raman active vibrational band at around 1605 cm−1 (see Supplementary Results), overlapping with the G band. Nevertheless, utilising the proposed signal enhancing design, the observation of the G band as a broad shoulder on this band is feasible (Fig. 4b). In addition, similar results were obtained for nanocomposites with graphene instead of GO.
The close agreement, in Fig. 4f, between the relative intensities of the D and G bands found experimentally for all nanocomposites (points) and those determined numerically (solid lines) verifies the method for predicting the Raman signal enhancement. For both the D and G bands, the numerically determined enhancement ratio was within the error of the experimental measurements; slight differences occur due to the flake not being positioned precisely at the centre of the channel. Therefore, this technique presents an effective tool for maximising the enhancement of the Raman signal.
Understanding the dynamics of 2D nanoplatelet spatial alignment is essential for the realisation of three-dimensional metastructure formation. External stimuli, such as applied electric field and light coupling6,15 [See Supplementary Results and Supplementary Videos 1,2,3,4], induce dynamic re-ordering of suspended 2D nanoparticles. Here, a Raman laser was exploited to move a GO flake within a channel (Fig. 5a), while simultaneously being used to monitor the xyz alignment over time. The variation in the experimental Raman spectra for different flake positions within the channel is illustrated in Fig. 5b.
The effect of the flake position on the Raman signal intensity was modelled by varying the position of the oscillating dipoles within the optofluidic waveguide channel both laterally and vertically. The ratio of the D and G band intensities is not constant as the position is varied (Fig. 5c–d). For lateral displacements (Fig. 5c), there are ratios of 11 and 32 between the minimal and maximal intensities determined numerically for the D and G bands respectively. For vertical displacements (Fig. 5d), the maximum and minimum values of the average intensity differ by factors of around four and five times for the D and G bands respectively.
For the lateral displacement of the flake, the ratios of the intensities of the GO D and G bands were extracted from experimental spectra when a flake was next to the wall and when moved further towards the centre of the channel. These ratios were then used as a multiplier on the numerically determined intensity for the flake next to the wall (position 2 in Fig. 5a) to determine an approximate displacement. Positions approximated using experimental data in tandem with the numerically determined results are closely matched to the values observed using optical microscopy techniques (See Supplementary Results), falling within the experimental error. The lateral position can therefore be determined with similar precision to optical microscopy (approx. ± 5%) currently, but with scope for the error to be reduced significantly by improving the signal-to-noise ratio.
For the vertical displacement of the flake, again the ratios of the intensities of the GO D and G bands were extracted, this time from data with the flake at the bottom of the channel and further towards the surface. The ratios were then used to multiply the numerically determined intensity with the flake at the bottom of the channel to determine an approximate displacement. The numerical analysis covering the effect of vertical flake position shows close agreement with the experimental data. The vertical position of the flake cannot be determined from optical microscopy but the close agreement of the positions determined separately from the D and G bands confirms that the method is accurate. Therefore, the predictions made from the Raman spectra are the most accurate method of determining the vertical position currently available. While we propose this technique as a method for monitoring self-assembly of 3D metastructures comprised of 2D materials, this approach may also find applications in a wide range of other areas such as controlling flake alignment for liquid phase deposition of 2D materials24,26 or for spatial monitoring of nanoparticle distributions35.
In summary, we propose a novel approach for integration of 2D materials on CMOS photonic chip utilising microfluidics technology. We have successfully demonstrated that this approach can be used for integration of any fluid-dispersed 2D nanoparticles on SOI photonics platform. The optofluidic system design can be optimised to enable in-situ Raman spectroscopy monitoring of 2D dispersed flakes during device operation. In-situ label-free 2D flake sensing via selective enhancement of the Stokes Raman signal at given wavelengths has been determined numerically and confirmed experimentally. This approach has been applied to monitor the individual 2D nanoplatelet dynamic within an optofluidic waveguide with high sensitivity, enabling precise in-situ alignment monitoring for the first practical realisation of 3D photonic metastructure shaping based on 2D-fluid composites and CMOS photonics platform.
How to cite this article: Hogan, B. T. et al. Dynamic in-situ sensing of fluid-dispersed 2D materials integrated on microfluidic Si chip. Sci. Rep. 7, 42120; doi: 10.1038/srep42120 (2017).
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
We acknowledge financial support from: The Engineering and Physical Sciences Research Council (EPSRC) of the United Kingdom via the EPSRC Centre for Doctoral Training in Electromagnetic Metamaterials (Grant No. EP/L015331/1) and also via Grant Nos. EP/N035569/1, EP/G036101/1, EP/M002438/1, and EP/M001024/1, Science Foundation Ireland Grant No. 12/IA/1300, the Ministry of Education and Science of the Russian Federation (Grant No. 14.B25.31.0002) and the Royal Society Research Grant RG2016 R1 and International Exchange Grant 2015/R3. The microfluidic structures were fabricated at Tyndall National Institute under the Science Foundation Ireland NAP368 and NAP94 programs.