Skip to main content

Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Rayleigh scattering in few-mode optical fibers

Abstract

The extremely low loss of silica fibers has enabled the telecommunication revolution, but single-mode fiber-optic communication systems have been driven to their capacity limits. As a means to overcome this capacity crunch, space-division multiplexing (SDM) using few-mode fibers (FMF) has been proposed and demonstrated. In single-mode optical fibers, Rayleigh scattering serves as the dominant mechanism for optical loss. However, to date, the role of Rayleigh scattering in FMFs remains elusive. Here we establish and experimentally validate a general model for Rayleigh scattering in FMFs. Rayleigh backscattering not only sets the intrinsic loss limit for FMFs but also provides the theoretical foundation for few-mode optical time-domain reflectometry, which can be used to probe perturbation-induced mode-coupling dynamics in FMFs. We also show that forward inter-modal Rayleigh scattering ultimately sets a fundamental limit on inter-modal-crosstalk for FMFs. Therefore, this work not only has implications specifically for SDM systems but also broadly for few-mode fiber optics and its applications in amplifiers, lasers, and sensors in which inter-modal crosstalk imposes a fundamental performance limitation.

Introduction

The discovery by Kao that the optical loss of silica fiber could be reduced to below 20 dB/km1 has spurred the growth of fiber optics and its applications in optical communication2. Today, optical fibers have become the backbone that supports the internet. Because of the exponentially-increasing bandwidth demand, optical-communication systems based on single-mode fibers have been driven to their capacity limits. Space-division multiplexing (SDM)3,4,5,6 including mode-division multiplexing (MDM)7 and core multiplexing, has been proposed as the next-generation solution to further increase the transmission capacity8,9,10,11,12,13,14,15,16. Ideally, an N-mode optical fiber could permit N channels to transmit independent data and therefore increasing the transmission capacity by a factor of N, in comparison with a single-mode fiber. Rayleigh scattering is an inherent process that will affect signal propagation in these channels. Additionally, crosstalk among these channels due to random mode-coupling17,18,19 induced either by perturbation or by fiber imperfections exists. Because inter-modal crosstalk renders these channels interdependent17,20, multiple-input-multiple-output18 (MIMO) digital-signal processing (DSP) is needed at the receiver for de-multiplexing the signals. Because the MIMO DSP complexity scales as N2, optical fibers with a few modes, or, so-called few-mode fibers (FMFs), have been deployed for SDM systems.

Rayleigh scattering has been studied in single- and multi-mode optical fibers. And the relevant theories are well established. In particular, with regard to the Rayleigh scattering theory developed for MMFs21, a mode-continuum model was adopted and an incoherent total power transfer formulism was established. However, mode-resolved Rayleigh scattering in few-mode fibers has not been systematically investigated. In this work, we establish a general model for Rayleigh scattering in FMFs and verify the model experimentally. The model permits analytical calculations of time-dependent, mode-resolved power of Rayleigh scattering, including the forward and backward, intra-modal and intermodal cases. This model not only can provide the theoretical foundation for optical time-domain reflectometry in few-mode fibers, but also be used to probe the random mode-coupling dynamics caused by perturbation. Furthermore, we found that even in absence of external perturbation and fiber imperfections, inter-modal crosstalk in FMF still exists due to the existence of forward, inter-modal Rayleigh scattering. Thus, it is the forward, inter-modal Rayleigh scattering that makes crosstalk an inerasable signature in FMFs and sets the crosstalk limit. Our illustration of the role of Rayleigh scattering in FMFs can guide future design and optimizations of hardware and algorithms of SDM transmission systems and networks. The general theoretical framework for Rayleigh scattering in FMFs, on the other hand, can be used to analyze the Rayleigh-scattering signals that are used for probing the mode-coupling dynamics in FMFs, and impact fiber lasers22, amplifiers23, and sensors24, in which FMFs are used and inter-modal crosstalk is therefore a fundamental limitation.

Results

Theory

We used a three-mode optical fiber, containing the LP01, LP11a, and LP11b modes, as an example to study Rayleigh scattering. The theory we developed here, however, can be extended to an arbitrary number of modes. The experiment, in principle, can also be trivially extended with the availability of efficient multiplexers/demultiplexers. In this work we didn’t take polarizations into account and treated Rayleigh scattering as a scalar process.

We derived the equation for mode-resolved time-dependent power of Rayleigh back-scattering received at the front end of the fiber. To develop the theory, we assumed that an optical pulse, with a temporal width of ΔT and a constant power P0 was launched at z = 0 into mode i (i = 1, 2, 3) of the three-mode fiber. In the main text of the paper, as well as in the Supplementary Information (SI), we use subscripts 1, 2, and 3 to represent the LP01, LP11a, and LP11b modes, respectively. The time-dependent power of Rayleigh back-scattering in mode j( j = 1, 2, 3) received at z = 0 can be calculated by

where ; ; ; vgi and vgj are the group velocities of modes i and j, respectively; αi and αj are the optical attenuation coefficients of modes i and j, respectively; αs(z) is the ratio of the total scattered power at z to the incident power at z; Bij(z) is the overall capture fraction, quantifying the ratio of the scattered power into mode j to the total scattered power at z. Detailed derivation of Eq. (1) using space-time diagrams is presented in Section I of SI. If we further assume that αs(z) = αs, Bij(z) = Bij, and (see Section I of SI for justifications), where , Eq. (1) can be approximated as

We note that Eq. (2) becomes identical to the equation for the single-mode case25 if we set i = j = 1, vgi = vgj = vg, and αi = αj = α.

In Eq. (2), the overall capture fraction, Bij, can be calculated by averaging the local capture fraction, bj(R, ϕ), over the near-field intensity distribution of the incident mode i:

where

in which ψNj and ψFj represent the near and far fields (see Section II of SI) of mode j, respectively; ψs is the field radiated by a dipole (see Section III of SI). Rayleigh scattering at (Rs, ϕs) is modeled as the field of a dipole located at (Rs, ϕs). Following derivations detailed in Section IV of SI, we obtain bj(j = 1, 2, 3):

and

where R′ = R/a, a is the radius of the core of the optical fiber, . From Eqs (3), (5), (6) and (7), we obtain Bij:

The parameters Bij satisfy the following relations (see Section V of SI):

and

Figure 1 presents the local capture fraction, bj( j = 1, 2, 3). As expected [see Eqs (5), (6) and (7)], the distribution of bj across the cross-section of the fiber closely mimics the intensity distribution of the near field of mode j. Indeed, we calculated bj using Eq. (4) directly without approximations and found that the maximum relative difference was 6% in the core (see Section IV of SI). This comparison justifies the approximations we used.

Figure 1
figure1

Local capture fraction of Rayleigh back-scattering in few-mode fibers.

(a), (b) and (c) are for the excitations by LP01, LP11a, and LP11b modes, respectively.

Figure 2 presents the overall capture fraction, Bij, as a function of normalized frequency V ≡ 2πaNA/λ, where a is the core radius of the fiber, NA is the numerical aperture of the fiber, and λ is the wavelength in free space. The dashed line shows the normalized cut-off frequency for the LP11a and LP11b modes, at V = 2.405. Our experiment was performed at V = 3.49.

Figure 2
figure2

Overall capture fraction of Rayleigh back-scattering in few-mode fibers.

The dashed vertical line corresponds to V = 2.405, the normalized cut-off frequency for the LP11a and LP11b modes.

The degeneracy and the relative magnitudes of Bij in Eqs (8) and (9) can be clearly seen in Fig. 2, and are understandable from the mode distribution and the associated symmetries. We note that our result of B11 is almost identical with the single-mode result reported in ref. 24 with discrepancies due to the differences of fiber parameters.

Before we further discuss the case of forward scattering and its impact on inter-modal crosstalk, we first verify the newly-developed model via OTDR measurement of the backscattering. This is because the theories for forward- and backward-scattering share significant similarities. After we place the backward-scattering case on a solid ground, we can develop the forward case by analogy.

Experiment

We measured the time-dependent power of Rayleigh back-scattering using the experimental setup schematically shown in Fig. 3. The procedure of the measurement is detailed in the section of Methods. Figure 4 presents the experimental and theoretical results of time-dependent :

Figure 3
figure3

Schematic of the experimental setup used for measuring Rayleigh back-scattering in a three-mode optical fiber.

A commercial OTDR was used for excitation and detection. Laser pulses from the OTDR, at the wavelength of 1550 nm, with 100-ns width and 37-mW peak power, were launched into a free-space mode-multiplexer/de-multiplexer and then into the three-mode optical fiber. The reflected light and Rayleigh back-scattering were demultiplexed, then went through an acousto-optic modulator (AOM), and finally went back into the OTDR through a circulator. The output of the photodetector triggers the signal generator; the output of the signal generator modulates the 55-MHz driving signal of the AOM, generating a 50-μs window that the OTDR receives Rayleigh back-scattering. C: circulator; L: lens; BS: beam splitter; M: mirror; SMF: single-mode fiber; FMF: few-mode fiber; PP1: phase plate 1 for the LP11a channel; PP2: phase plate 2 for the LP11b channel; AOM: acousto-optic modulator; EDFA: erbium-doped fiber amplifier; PD: photodetector; SG: signal generator.

Figure 4
figure4

Optical-time-domain-reflectometer measurement of Rayleigh back-scattering in a three-mode optical fiber and the corresponding theoretical results.

(a) experimental results with LP01 excitation; (b) theoretical results with LP01 excitation; (c) experimental results with LP11a excitation; (d) theoretical results with LP11a excitation; (e) experimental results with LP11b excitation; (f) theoretical results with LP11b excitation; (g) comparison of the experimental and theoretical intercepts relative to Ii1.

The experimental data were raw data obtained by OTDR measurement averaged over 30 seconds, taking into account the insertion and coupling losses, Lij. Section VI of SI presents the measurement of Lij in detail. For calculating the theoretical curves, we used the values obtained by fitting the experimental data of for αi and αj; αs ≈ −0.039/km as in ref. 26; vgi ≈ vgj ≈ 2.067 × 105 km/s. To quantify the relative difference between theoretical and experimental results, we compare the intercepts at z = 0 of the OTDR curves, as relative to , as shown in Fig. 4(g). The uncertainties in our measurement in Fig. 4(g) are primarily from the uncertainties of the measurement of Lij(See Section VII of SI). The differences between theoretical and experimental results for I11-I12, I11-I13, I21-I22, and I31-I33 are 0.15 dB, −0.23 dB, −0.28 dB, and 0.15 dB, respectively, evidencing the validity of our theory that does not take into account the inter-modal coupling of the excitation. However, the differences for I21-I23 and I31-I32 are significantly larger, which are 1.19 dB and 1.22 dB, respectively. The reason for the larger differences is that in our fiber, LP11a and LP11b are degenerate modes and they are strongly coupled. For the case that we launch LP11a and receive LP11b, a portion of the optical power is coupled from the LP11a mode to LP11b mode as the excitation light in the LP11a mode is propagating in the forward direction. Because B33 = 3B23, the measured backscattering in LP11b that contains the backscattering from both the forward-propagating LP11a and LP11b modes is larger than what the theory predicts, i.e., experimental I23 is larger than theoretical I23, and therefore, theoretical I21-I23 is larger than experimental I21-I23. The same argument applies to I31-I32. Using the same method that we developed here, we tested two additional pieces of few-mode optical fibers: one is a step-index fiber and another is a graded-index fiber. Section IX of SI presents the description of the fiber characteristics and the results of the measurement. The results on these three fibers consistently show that in absence of strong coupling as our theory assumes, experimental and theoretical results match, leading us to conclude that our theory on Rayleigh scattering in few-mode optical fiber is valid.

Inter-modal crosstalk due to Rayleigh forward scattering

For the forward-scattering case, following almost identical derivations as in Section I of SI, we can similarly write down the power of Rayleigh scattering excited by mode i, and scattered forward into mode j received at z = lF as:

We simplify Eq. (10) by similarly assuming that αs(z) and Fij(z), the overall capture fraction for forward-scattering, are independent with z, i.e., αs(z) = αs and Fij(z) = Fij. Additionally, we assume that the incident light in mode i is continuous wave (CW) with a constant power Pi. Thus,

From symmetry consideration, Fij = Bij, i.e., the corresponding overall capture fraction of forward and backward scattering are identical. Therefore, the inter-modal crosstalk due to Rayleigh forward scattering is

Figure 5 is the semi-log plot of the non-diagonal elements of crosstalk due to Rayleigh forward-scattering, as functions of distance. Inter-modal Rayleigh forward-scattering between the LP01 and LP11a(b) modes are stronger than that between the LP11a(b) and LP11b(a) modes. Inter-modal Rayleigh forward-scattering increases with z at the beginning because the scattered power from mode i keeps accumulating in mode j. At longer propagation distance, the coupled power decreases as z increases because the incident light in mode i attenuates due to propagating loss and the scattered light in mode j decreases in proportion to the local excitation. A maximum appears in between. Eq. (11) shows that Rayleigh forward-scattering is maximum at

Figure 5
figure5

Crosstalk due to inter-modal Rayleigh forward-scattering, as a function of distance.

The crosstalk in all the cases studied follows the same pattern: it increases with distance first and then decreases.

Discussion

The inter-modal crosstalk induced by forward Rayleigh scattering is difficult to observe experimentally because it is usually shadowed by random mode coupling induced by perturbations and mode coupling resulted from fiber imperfections. One concrete example of fiber imperfections is the imperfections at the interface between the core and cladding layer, which results in so-called small-angle scattering27,28. Random mode coupling induced by perturbations and mode coupling due to small-angle scattering have not been included in our theoretical analysis that only focuses on the effect of Rayleigh scattering. In our case, α1 = 0.209 dB/km, α2 = 0.210 dB/km, and α3 = 0.233 dB/km. We can use Eq. (14) to get km, km, and km. The maximum crosstalk due to Rayleigh forward scattering Tij is - 37 dB, which is 7.51 dB smaller than the minimum total crosstalk (−29.49 dB for the case LP01 → LP11b) due, dominantly, to random mode-coupling and fiber imperfections that we measured in this three-mode optical fiber (See Section X of SI). Random mode crosstalk can be significantly reduced by, for example, increasing the effective index difference between modes29. On the contrary, Rayleigh scattering of optical fibers cannot be significantly reduced because random density fluctuations due to the irregular microscopic structure at the glass softening temperature that are “frozen in”30. Hence, inter-modal Rayleigh forward-scattering will likely set the fundamental baseline for crosstalk in MDM systems. This baseline for crosstalk, similar to the baseline for optical attenuation, can be reduced by, for example, using pure-silica core fiber31, but cannot be eliminated.

In conclusion, we have systematically studied Rayleigh scattering in few-mode optical fibers. We have established a complete model for both backward and forward scatterings that allows us to calculate the time-dependent, mode-resolved Rayleigh scattering power and have verified our theory experimentally. We have found that Rayleigh forward-scattering is a fundamental mechanism for inter-modal crosstalk. Our theoretical and experimental results show that this crosstalk is 7.51 dB smaller than the total crosstalk measured in the three-mode optical fiber used in the current experiment that is due dominantly to random mode coupling and fiber imperfections. While random mode coupling can be significantly reduced by increasing the effective index difference between modes, crosstalk induced by Rayleigh forward-scattering cannot be reduced much further. We anticipate the impact of our work as follows. First, it can guide the design and optimization of hardware and algorithms of SDM communication systems. Second, it can serve as the foundations for optical time-domain reflectometry that uses Rayleigh scattering to probe the perturbation-induced mode-coupling dynamics in SDM systems. In particular, the theory developed here can further include perturbations to quantitatively model the probing signal in this scenario. Finally, in a broader context, it can be useful for designing and implementing various few-mode active and passive devices, including amplifiers, lasers, and sensors, in which Rayleigh scattering imposes a fundamental performance limitation.

Methods

Measurement of Rayleigh backscattering

As shown in Fig. 3, a commercial optical time-domain reflectometer (OTDR) (YOKOGAWA AQ7285) with a 50-dB dynamic range was used to launch optical pulses at the central wavelength of 1550 nm, each with a pulse width of ΔT = 100 ns and peak power of P0 = 37 mW, into a 4.75-km-long three-mode optical fiber through a free-space mode multiplexer/de-multiplexer. The refractive indices of the core and cladding of the fiber are 1.4495 and 1.4440, respectively; the diameter of the core is 13.69 μm; the numerical aperture (NA) of the fiber is 0.1259. The single-pass insertion loss between the first circulator and the last coupling lens of the mode multiplexer/de-multiplexer was 5.85 dB, 9.83 dB and 9.22 dB for the LP01, LP11a, and LP11b channels, respectively. The coupling losses from free space to the fiber were 0.50 dB, 2.51 dB, and 2.89 dB for the LP01, LP11a, and LP11b channels, respectively. Section VI of SI details the measurement of optical losses. The reflected light and Rayleigh back-scattering in these three modes were de-multiplexed and then sent back to the OTDR through circulators. We used an acousto-optic modulator (Brimrose AMM-55-8-70-1550-2FP) to eliminate strong optical reflection at the facet (see Section VIII of SI for more details). This reflection would otherwise generate a dead zone approximately from 0 to 1.5 km. Figure 4 shows the configuration when the excitation is in the LP11b mode and the signal collected is in LP01 mode. We manually reconfigured the fiber connections for other combinations of excitation and collected channels.

Additional Information

How to cite this article: Wang, Z. et al. Rayleigh scattering in few-mode optical fibers. Sci. Rep. 6, 35844; doi: 10.1038/srep35844 (2016).

References

  1. Kao, K. C. & Hockham, G. A. Dielectric-fibre surface waveguides for optical frequencies. Proceedings of the Institution of Electrical Engineers 113, 1151–1158 (1966).

    Article  Google Scholar 

  2. Agrawal, G. P. Optical-fiber communication systems (Wiley, 2003).

  3. Li, G., Bai, N., Zhao, N. & Xia, C. Space-division multiplexing: the next frontier in optical communication. Adv. Opt. Photon 6, 413–487 (2014).

    Article  Google Scholar 

  4. Richardson, D., Fini, J. & Nelson, L. Space-division multiplexing in optical fibres. Nat. Photonics 7, 354–362 (2013).

    CAS  ADS  Article  Google Scholar 

  5. Winzer, P. J. Optical networking beyond WDM. IEEE Photon. Journal 4, 647–651 (2012).

    ADS  Article  Google Scholar 

  6. Zhao, N., Li, X., Li, G. & Kahn, J. M. Capacity limits of spatially multiplexed free-space communication. Nat. Photonics 9, 822–826 (2015).

    CAS  ADS  Article  Google Scholar 

  7. Berdagué, S. & Facq, P. Mode division multiplexing in optical fibers. Appl. Opt. 21, 1950–1955 (1982).

    ADS  Article  Google Scholar 

  8. Yaman, F., Bai, N., Zhu, B., Wang, T. & Li, G. Long distance transmission in few-mode fibers. Opt. Express 18, 13250–13257 (2010).

    ADS  Article  Google Scholar 

  9. Bai, N. et al. Mode-division multiplexed transmission with inline few-mode fiber amplifier. Opt. Express 20, 2668–2680 (2012).

    ADS  Article  Google Scholar 

  10. Watanabe, T. & Kokubun, Y. Over 300 channels uncoupled few-mode multi-core fiber for space division multiplexing. Optical Fiber Communication Conference, Optical Society of America, Th2A.50 (2014).

  11. Takahashi, H. et al. First demonstration of MC-EDFA-repeatered SDM transmission of 40 × 128-Gbit/s PDM-QPSK signals per core over 6,160-km 7-core MCF. Opt. Express 21, 789–795 (2013).

    CAS  ADS  Article  Google Scholar 

  12. Sakaguchi, J. et al. 305 Tb/s space division multiplexed transmission using homogeneous 19-core fiber. J. Lightwave Technol 31, 554–562 (2013).

    ADS  Article  Google Scholar 

  13. Qian, D. et al. 1.05 Pb/s transmission with 109 b/s/Hz spectral efficiency using hybrid single- and few-mode cores. Frontiers in Optics, Optical Society of America, FW6C. 3 (2012).

  14. Yaman, F., Bai, N., Huang, Y., Huang, M., Zhu, B., Wang, T. & Li, G. 10 × 112 Gb/s PDM-QPSK transmission over 5032 km in few-mode fibers. Opt. Express 18, 21342–21349 (2010).

    ADS  Article  Google Scholar 

  15. Li, A., Chen, X., Al, A. A., Ye, J. & Shieh, W. Space-division multiplexed high-speed superchannel transmission over few-mode fiber. J. Lightwave Technol. 30, 3953–3964 (2012).

    ADS  Article  Google Scholar 

  16. Van, U. R. et al. Ultra-high-density spatial division multiplexing with a few-mode multicore fibre. Nat. Photonics 8, 865–870 (2014).

    ADS  Article  Google Scholar 

  17. Antonelli, C., Mecozzi, A., Shtaif, M. & Winzer, P. J. Random coupling between groups of degenerate fiber modes in mode multiplexed transmission. Opt. Express 21, 9484–9490 (2013).

    ADS  Article  Google Scholar 

  18. Ryf, R. et al. Mode-division multiplexing over 96 km of few-mode fiber using coherent 6 × 6 MIMO processing. J. Lightwave Technol. 30, 521–531 (2012).

    ADS  Article  Google Scholar 

  19. Arik, S. O., Askarov, D. & Kahn, J. M. Effect of mode coupling on signal processing complexity in mode-division multiplexing. J. Lightwave Technol. 31, 423–431 (2013).

    ADS  Article  Google Scholar 

  20. Yaman, F., Mateo, E. & Wang, T. Impact of modal crosstalk and multi-path interference on few-mode fiber transmission. Optical Fiber Communication Conference. Optical Society of America, OTu1D. 2 (2012).

  21. Mickelson, A. R. & Eriksrud, M. Theory of the backscattering process in multimode optical fibers. Appl. Opt 21, 1898–1909 (1982).

    CAS  ADS  Article  Google Scholar 

  22. Jeong, Y., Sahu, J. K., Payne, D. N. & Nilsson, J. Ytterbium-doped large-core fiber laser with 1.36 kW continuous-wave output power. Optics Express 12, 6088–6092 (2004).

    CAS  ADS  Article  Google Scholar 

  23. Sheng, Z. X. Theoretical analysis of Rayleigh backscattering noise in fiber Raman amplifiers. Communications in Theoretical Physics 44, 908 (2005).

    ADS  Article  Google Scholar 

  24. Polynkin, P., Polynkin, A., Peyghambarian, N. & Mansuripur, M. Evanescent field-based optical fiber sensing device for measuring the refractive index of liquids in microfluidic channels. Optics Letters 30, 1273–1275 (2005).

    ADS  Article  Google Scholar 

  25. Hartog, A. H. & Gold, M. P. On the theory of back-scattering in single-mode optical fibers. J. Lightwave Technol. 2, 76–82 (1984).

    ADS  Article  Google Scholar 

  26. Tsujikawa, K., Tajima, K. & Zhou, J. Intrinsic loss of optical fibers. Optical Fiber Technology 11, 319–331 (2005).

    CAS  ADS  Article  Google Scholar 

  27. Rawson, E. G. Analysis of scattering from fiber waveguides with irregular core surfaces. Appl. Opt. 13, 2370–2377 (1974).

    CAS  ADS  Article  Google Scholar 

  28. Mazumder, P., Logunov, S. & Raghavan, S. Analysis of excess scattering in optical fibers. J. Appl. Phys. 96, 4042–4049 (2004).

    CAS  ADS  Article  Google Scholar 

  29. Maruyama, R., Kuwaki, N., Matsuo, S. & Ohashi, M. Experimental investigation of relation between mode-coupling and fiber characteristics in few-mode fibers. Optical Fiber Communication Conference, Optical Society of America, M2C.1 (2015).

  30. Tsujikawa, K., Tajima, K. & Ohashi, M. Rayleigh scattering reduction method for silica-based optical fiber. J. Lightwave Technol. 18, 1528–1532 (2000).

    CAS  ADS  Article  Google Scholar 

  31. Kanamori, H. et al. Transmission characteristics and reliability of pure-SiO2-core single-mode fibers. J. Lightwave Technol. 4, 1144–1150 (1986).

    ADS  Article  Google Scholar 

Download references

Acknowledgements

This work was supported by National Basic Research Program of China (973) (No. 2014CB340104/1) and National Science Foundation China (project number: 61377076). The authors want to thank Mr. Zhiqun Yang for helpful discussions and thank Mr. Hao Wu from Yokogawa Shanghai Trading CO., LTD. for lending us the OTDR with a 50-dB dynamic range.

Author information

Affiliations

Authors

Contributions

X.H., G.L. and N.Z. conceived the study. Z.W. and X.H. designed and did the experiment. Z.W., H.W. and X. H. developed the theory and analyzed the data. Q.M. made and provided the three-mode optical fiber used in the experiment. X.H., Z.W., H.W. and G.L. prepared the manuscript.

Ethics declarations

Competing interests

The authors declare no competing financial interests.

Electronic supplementary material

Rights and permissions

This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Wang, Z., Wu, H., Hu, X. et al. Rayleigh scattering in few-mode optical fibers. Sci Rep 6, 35844 (2016). https://doi.org/10.1038/srep35844

Download citation

Further reading

Comments

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

Search

Quick links