Skip to main content

Thank you for visiting You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Unravelling the low-temperature metastable state in perovskite solar cells by noise spectroscopy


The hybrid perovskite methylammonium lead iodide CH3NH3PbI3 recently revealed its potential for the manufacturing of low-cost and efficient photovoltaic cells. However, many questions remain unanswered regarding the physics of the charge carrier conduction. In this respect, it is known that two structural phase transitions, occurring at temperatures near 160 and 310 K, could profoundly change the electronic properties of the photovoltaic material, but, up to now, a clear experimental evidence has not been reported. In order to shed light on this topic, the low-temperature phase transition of perovskite solar cells has been thoroughly investigated by using electric noise spectroscopy. Here it is shown that the dynamics of fluctuations detect the existence of a metastable state in a crossover region between the room-temperature tetragonal and the low-temperature orthorhombic phases of the perovskite compound. Besides the presence of a noise peak at this transition, a saturation of the fluctuation amplitudes is observed induced by the external DC current or, equivalently, by light exposure. This noise saturation effect is independent on temperature, and may represent an important aspect to consider for a detailed explanation of the mechanisms of operation in perovskite solar cells.


A recent breakthrough in dye-sensitized solar cells has been the introduction of organic-inorganic hybrid perovskite materials, such as CH3NH3PbI3, to improve the power conversion efficiency1. Although not very efficient at the beginning, perovskite solar cells have quickly become very promising low-cost alternatives to traditional semiconductors, due to a regular achievement of 15% in efficiency with an NREL certified current record exceeding 22%2.

The use of perovskites in photovoltaics has attracted the scientific community, due to their peculiar chemical and physical properties, associated with a simple synthesis. In particular, it has been found that perovskites have bandgap energies in the near-infrared close to the Shockley-Queisser ideal limit1, elevated charge carrier mobilities, diffusion lengths on the order of micrometers3, and long charge carrier lifetimes4. All these characteristics, added to a certified stability under high proton irradiation, are useful for the development of a new and competitive photovoltaic technology, also functional for space applications5. In addition, hybrid perovskites are an ideal candidate for tandem solar cells with silicon, due to the low sub-bandgap absorption and the high bandgap energies. Various innovative concepts already showed the potential to outperform traditional single junction silicon solar cells6,7,8,9.

However, a clear picture of the electrical transport mechanisms in perovskites has not been achieved. Indeed, while there is a wide scientific literature on the photophysics of these materials in the room and high temperature regimes10,11,12,13,14,15, the understanding of how the lowering of temperature affects the charge carrier dynamics remains, instead, scarce. As is quoted by Loi and Hummelen12: “it is now time to investigate all the physical properties that make hybrid perovskites so promising for solar energy conversion”. In this respect, the carrier kinetic processes after optical excitation have been investigated3, and theoretical calculations have been performed by using experimental findings from: temperature-dependent absorption spectra, millimeter-wave spectroscopy, low-frequency dielectric measurements, and NMR data related to the motion of molecular cations16. Photoluminescence properties, under one-photon and two-photon excitation, have been also studied in CH3NH3PbBr3 microdisks, giving a more comprehensive understanding of the nonlinear effect of organic-inorganic perovskite single crystals17.

Among the available non-destructive characterization techniques, noise spectroscopy has demonstrated its effectiveness in the investigation of advanced photovoltaic and innovative materials18,19,20,21. Preliminary characterizations have also been performed in mesoscopic perovskite photodiodes22. Moreover, by studying the frequency and temperature dependencies of the 1/f spectral noise density, changes in the structural properties of nickel-titanium binary alloys23 and of iron-based superconductors24,25 have been revealed. In the case of perovskite solar cell devices, where a phase transition from a tetragonal to an orthorhombic structure has been observed near 160 K26, noise measurements can be a very useful experimental technique, considering that no clear signature of such a transition is evident in the cell DC properties.

In this work, a detailed analysis of the fluctuation processes has been performed in methylammonium lead iodide (CH3NH3PbI3) samples by varying temperature, bias current, and illumination level. The reported results shine light on the role played by excitons in the photoexcited carrier dynamics, and on the temperature dependence of localization effects, including phonon coupling and charge carrier trapping27,28. These phenomena need to be clarified, because of their potential to influence the efficiency of charge transport within the perovskite film.


Structural and photoelectric properties

Hybrid perovskites are an efficient light harvester within mesoscopic solar cells29. However, when using such a mesoscopic TiO2 scaffold, good charge carrier transport properties are unnecessary. Performance, instead, is related to the interfacial properties13. Today’s best performing devices, on the other hand, rely on thicker perovskite layers30,31, as it is also the case of the photovoltaic devices studied here. The understanding of the carrier transport mechanisms, therefore, becomes important10,11. Figure 1a shows a typical device scheme of an inverted perovskite solar cell, consisting of the layer stack glass/ITO/PEDOT:PSS/CH3NH3PbI3/PC61BM/BCP/Ag. Figure 1b shows a cross sectional scanning electron micrograph. The perovskite absorber has a thickness of around 430 nm. Identically processed devices revealed an average efficiency about 11% at room temperature and simulated AM 1.5G illumination. The current density-voltage (J-V) characteristics of the best performing device, with an efficiency of 12.1%, is depicted in Fig. 1c. In contrast to perovskite solar cells based on TiO232, the inverted device is hysteresis free33, as evident from the shown J-V sweeps in forward and backward direction. A power point tracking algorithm additionally verifies an efficiency of 12.04% after stabilization, as indicated by the red dot (see also Supplementary Fig. S1). The external (EQE) and internal quantum efficiency (IQE) are depicted in Fig. 1d. The integrated short-circuit current density amounts to 17.4 mA cm−2, and, therefore, matched the current obtained under AM 1.5G illumination.

Figure 1
figure 1

Perovskite solar cell characteristics at room temperature.

(a) Sketch of the used inverted perovskite solar cell structure. (b) Cross sectional scanning electron micrograph. (c) Current density-voltage characteristics of the best performing device. Black and red lines refer to performed forward and backward voltage scans, respectively. The result of a maximum power point tracking after stabilization verifies the power conversion efficiency of 12% (red dot). The inset shows a histogram of the measured efficiency of 20 processed devices. (d) The wavelength-dependent external (EQE) and internal quantum efficiency (IQE) plotted as black and red lines. The blue dashed line refers to the measured reflection R as (1 − R).

In addition to the typical standard test conditions at room temperature, perovskite solar cells were probed as a function of temperature from 300 K down to 60 K. This time, a commercial white Light Emitting Diode (LED) was used as light source (see Methods section for details). In Fig. 2, the temperature dependencies of the open-circuit voltage Voc (left axis) and of the short-circuit current density Jsc (right axis) are shown at three different illumination levels. A change in the behaviour of Voc (black closed symbols), in a temperature range between 150 and 100 K, is clearly evident, while a less pronounced effect is found for Jsc (coloured open symbols) independently on the light intensity. This result suggests the occurrence of a modification in the electrical properties of the photovoltaic device. However, no specific information can be extracted on the typology of the observed phenomenon. The question is whether the structural transition from a tetragonal to an orthorhombic phase (occurring around 160 K) plays any role in the low-temperature conduction regime of perovskite photovoltaic devices. In order to shed light on this aspect, a more sensitive investigation technique is needed.

Figure 2
figure 2

Optoelectronic properties from room temperature down to 60 K.

The temperature dependencies of the open-circuit voltage Voc (left axis) and of the short-circuit current density Jsc (right axis) are shown at three distinct illumination levels, supplied with a cool white LED as light source.

Electric noise spectroscopy

Electric noise analysis is usually made by measuring the spectral density of voltage fluctuations SV in a DC current biased sample. In semiconducting devices, the main noise source is due to charge number fluctuations, therefore, a more representative quantity for the noise spectral density is , where RD is the differential resistance at the DC bias point. In Fig. 3a,c, the I-V characteristics are shown at two temperatures (200 and 300 K, respectively) for two distinct samples, named as sample #1 (“thin”) and sample #2 (“thick”), whose structural difference can be clearly observed in the scanning electron micrographs of Supplementary Fig. S2. Despite the shape of dark I-V curves looks different, the photoelectric parameters of the investigated devices are similar (see the values reported in Supplementary Fig. S3), and a general trend can be also found in the current-noise spectra. This is evident in Fig. 3b,d, where the low-frequency dependence of SI is shown for the corresponding bias points of Fig. 3a,c. More in details, SI increases with the applied bias current until the occurrence of a saturation for values higher than 0.2 mA (see the blue spectral traces 4 in Fig. 3b,d). When the electric noise is saturated, a pure 1/f component is visible, as shown by curves 5 and 6 in Fig. 3b,d. Conversely, in the low bias current limit, SI is characterized by the presence of two cut-off frequencies, each one specific of a change from a 1/f to a 1/f3 dependence of the spectrum (spectral traces 1–3 of Fig. 3b,d). In particular, the highest cut-off frequency can be defined in terms of a time constant which describes the recombination phenomena associated to the defect states18. From noise spectroscopy, this time constant is estimated to assume temperature-dependent values between 4 and 10 μs, giving the experimental quantification of the rate constant for the physical process that produces the electric noise in perovskite solar cells. It is clear, however, that there is a peculiar feature of the charge carrier fluctuation mechanisms, indicating a crossover between distinct noise regimes. This behaviour is confirmed on several devices, and at different temperatures, as shown by Supplementary Fig. S4.

Figure 3
figure 3

Noise spectra at different bias points.

(a,c) Dark I-V characteristics at temperatures of 200 and 300 K are shown for two perovskite solar cells: sample #1 device B and sample #2 device B, respectively. (b,d) The frequency dependence of the current-spectral density SI is shown for the two considered photovoltaic devices. The bias points, at which noise spectra have been acquired, are numbered from 1 (lowest current value used) to 6 (highest current value used).

The existence of a DC bias-induced noise saturation has been observed in dark condition, and is found also under light exposure. This is clearly visible in the inset a and inset b of Fig. 4, where the current noise computed at a reference frequency of 90 Hz is shown as a function of the DC bias current IDC and of the photogenerated current Iph, at a temperature of 255 K. By plotting the total current (IDC + Iph) dependence of the noise amplitude, all the experimental data distribute on a single curve (see Fig. 4). This confirms that the origin of the measured electric noise is due to the fluctuation of total charge carriers present in the device, either photogenerated or injected by the bias leads. In addition, a saturation of the noise amplitude is observed for currents above 0.4 mA, a value that is sample- and temperature-dependent. Although space-charge-limited current measurements may be very useful for a better understanding and, therefore, are currently in progress, an explanation of this behaviour can be given using the well-known excitation-trapping fluctuation model34. In this framework, the noise process derives from the assumption that free carriers are randomly trapped and released by centers with different times. The generation of carriers, induced by DC bias or by photocurrent, increases the trap filling until a noise saturation occurs, when all the traps are active.

Figure 4
figure 4

Noise current dependence in dark and under light exposure.

The spectral density SI, at a frequency of 90 Hz, is shown as a function of the total current for sample #1 device B at a fixed temperature of 255 K. A saturation of the noise amplitude is observed by varying, independently, the DC applied bias IDC (inset a) and the photogenerated current Iph (inset b). By considering the sum IDC + Iph, the noise saturation effect is estimated to occur near 0.4 mA.

An useful quantity to estimate the overall generated noise is the variance of voltage fluctuations Var[V], obtained by computing the integral of SV in the frequency domain between [fmin, fmax] = [1, 100000] Hz (the experimental bandwidth). In Fig. 5 the temperature dependence of Var[V], measured at large bias current (that is in the region of full trap activation), is shown for the investigated samples, characterized by different perovskite grains sizes and cristallinity. The reported values differ by two orders of magnitude, between sample #1 and sample #2, when similar bias currents are applied (2.9 mA for sample #1 and 2.94 mA for sample #2). By excluding a parasitic effect of the involved interfaces, which are identically processed, the measured noise fluctuations are dominated by a defect related trapping/detrapping mechanism within the bulk perovskite absorber. Therefore, the lower Var[V] of sample #2 indicates a lower trap density in the device of large grain size. The finding is consistent with the reported increase of the electron-hole diffusion length with increasing grain size10,35,36. The data of Fig. 5a, acquired both in dark and at different illumination intensity, reveal the presence of a noise peak at temperatures between 150 and 160 K. This feature is independent on the presence of photogenerated carriers, however it shows a clear dependence on the bias current, as visible in Fig. 5b. Moreover, above 160 K and below 130 K, the noise level decreases by increasing the current. Surprisingly, the opposite behaviour is found in the temperature region around the noise peak (see Fig. 5b). It is conceivable that the observed noise peak is related to the perovskite phase transition occurring in the temperature range near 160 K. A detailed discussion on how this influences the fluctuation processes is given below, providing a better understanding on the physical properties of perovskite photovoltaic devices.

Figure 5
figure 5

Temperature dependence of the noise level.

(a) The variance of the measured voltage fluctuations Var[V], at a fixed bias current value of 2.9 mA, is shown as a function of temperature for sample #1 device B. The black squares refer to data taken in dark condition, while red circles, green triangles, and blue diamonds correspond to three different illumination levels reported in the legend. (b) The temperature behaviour of the voltage-noise amplitude is shown for sample #2 device B, by varying the applied bias current. In all the cases considered, the presence of a noise peak is clearly visible between 150 and 160 K.


The repeatability and the intrinsic nature of the observed temperature noise behaviour have been verified by measuring the samples in cooling and heating modes, in the range between 70 and 300 K. The data shown in Supplementary Fig. S5 give a clear indication that hysteretic effects are not present in the experimental results, and no significant difference characterizes the temperature direction change.

After the verification of the reproducibility of the noise peak found near 155 K, a detailed study of the voltage-noise amplitude has been done for different bias points. In order to explain the measured voltage-spectral densities, the overall noise can be expressed as the sum of two independent contributions

In equation (1), the first term represents a current-noise source that is always present and takes into account the fluctuations due to active trapping states in the photovoltaic device. As specified before, this is modeled by the well-known trapping/detrapping mechanism, which induces charge carrier fluctuations and, consequently, a current noise SI34. The second term of equation (1) represents a voltage-noise source that, instead, describes a resistance network fluctuation mechanism SR, occurring in the perovskite phase-transition region where metastable states between local resistive states are established. While conventional silicon-based solar cells have already shown the presence of trapping-detrapping related processes37, resistive-induced fluctuators are usually found in random network systems38 but are unexpected in photovoltaic materials.

In Fig. 6a,c, the measured voltage-spectral density amplitudes are shown in the low (orthorhombic) and high (tetragonal) temperature regions, respectively. The experimental results indicate a direct proportionality of the noise level with the differential resistance squared, and are consistent with the presence of a current-noise source alone (first term of equation (1)). This noise contribution increases with temperature above 200 K, while, below 200 K, is substantially constant. However, in the region around 160 K, the experimental behaviour is completely different and is characterized by the appearance of an excess noise component, which can be extracted by subtracting from the measured noise level the constant current-noise term. The values of this excess noise contribution, shown in Fig. 6b,e as Var[V]trans, seem to scale well with the applied bias squared I2 and, conversely, have no relation with .

Figure 6
figure 6

Behaviour of the noise amplitude in different temperature regions.

(a,c) For sample #2 device B, the normalized noise amplitude is shown by varying the value of the differential resistance. (d,f) The bias current dependence of the normalized noise Var[V]I−2 is also shown for the same photovoltaic device. (b,e) The similar behaviour found for the tetragonal (T > 160 K) and the orthorhombic (T < 130 K) phases is no more observed in the transition region between 160 and 130 K, where the excess noise contribution Var[V]trans has been computed and reported.

The unexpected additional noise observed near 160 K can be explained by considering that, in this temperature region, the structural reorganization of the perovskite material produces a random distribution of microscopic phases, to which a random resistor network can be associated. The resistors fluctuate randomly between the values characteristic of the two perovskite phases, giving rise to a 1/f noise with a quadratic bias current dependence. This is exactly what is shown in Fig. 6e, where the excess noise level scaled with I2 exhibits a constant value, different for the specific temperatures investigated. The highest value is found at 155 K, indicating this as the structural transition temperature of the perovskite compound.

Figure 6d,f show that the quadratic bias scaling is not present outside the phase-transition region, confirming the proposed model. As a consequence, from the noise point of view, the low-temperature crossover between the tetragonal and orthorhombic phases can be clearly identified by the change from a trapping/detrapping to a resistance fluctuation mechanism. The structural reorganization of the microscopic metastable states, established in the transition region, may be characterized by long-term relaxation processes, which are probably connected with the two turning points (around 150 and 100 K) observed in the Voc temperature dependence (see Fig. 2 for details). More information on important electronic parameters of the solar cell defect states can be extracted by using a current-noise theoretical interpretation37, whose applicability to the case of perovskite compounds is currently in progress.


Hybrid perovskites are an ideal absorber for solar cells, but show various structural transitions upon temperature. For example, the CH3NH3PbI3 compound, here studied, changes from a tetragonal to an orthorhombic structure at low temperature. As a result the optoelectronic parameters, such as open-circuit voltage and short-circuit current density, present signs of irregular behaviour between 150 and 100 K. The DC analysis alone, however, is not able to provide clear indications on what is really happening. In this respect, it is possible to obtain much more information by the electric noise spectroscopy. In particular, the appearance of a noise level peak, independently on the illumination condition, allows an estimation of a temperature region where the nature of fluctuation mechanisms changes. Above 160 K (in the tetragonal phase) and below 130 K (in the orthorhombic phase), the electric noise is generally produced by a trapping/detrapping process. Resistance fluctuations, instead, are dominant in the phase-transition region, near the noise level peak. When the active traps are filled by the charge carrier generation, the trapping noise contribution saturates. Conversely, the amplitude of resistance fluctuations increases with the squared bias current, revealing the existence of a metastable state in the crossover between the tetragonal and orthorhombic structures of the perovskite compound. This metastable state may be attributed to a random distribution of microscopic phases. Therefore, in simple and complex mixed perovskite solar cells, where structural reorganizations induced by light, time, and temperature seem to be very relevant, a non-destructive and simple experimental technique, such as noise spectroscopy, can play an important role for the understanding of the physics of such devices.


Solar cells preparation

Perovskite solar cells were prepared following the layer sequence glass/ITO/PEDOT:PSS/CH3NH3PbI3/PC61BM/BCP/Ag. Therefore, patterned glass/ITO substrates were cleaned with acetone, detergent/H2O, H2O, and isopropanol. After a final plasma cleaning, a 60 nm thick PEDOT:PSS layer (Heraeus PH 4083) was prepared by spin-coating at 3000 rpm for 30 s. The obtained films were annealed at 150 °C for 20 min, before being transferred to inert atmosphere. A stoichiometric CH3NH3PbI3 precursor solution, containing either 0.8 M (thin sample) or 1.1 M (thick sample) of PbI2 (Sigma-Aldrich) and CH3NH3I (synthesized from CH3NH2 and HI26, Sigma-Aldrich) in the mixed solvent γ-butyrolactone (GBL) and dimethyl sulfoxide (DMSO) with volume ratio 70/30 (v.%/v.%), was prepared under stirring at 60 °C for 12 h. The CH3NH3PbI3 absorber was spin-coated at 1000 rpm for 10 s, 2000 rpm for 20 s, and 5000 rpm for 20 s. In the final spin-coating stage, 150 μl toluene were dripped onto the sample, according to Jeon et al.39. After crystallization at 100 °C for 10 min, a smooth CH3NH3PbI3 layer was obtained. The electron selective contact was formed by spin-coating a 50 nm thick PC61BM layer (Lumtec, 99.5%, 20 mg ml−1 in chlorobenzene) at 2500 rpm for 60 s. After annealing at 100 °C for 10 min, a thin layer of bathocuproine (BCP, 0.5 mg ml−1 in ethanol, Sigma-Aldrich) was spin-coated at 4000 rpm for 45 s. The devices were completed by thermal evaporation of 100 nm Ag at a base pressure of 10−7 mbar through a shadow mask. The overlap of the patterned ITO and the metal contact defined the active area of prepared devices to 0.16 cm2. For noise measurements, samples were encapsulated using a cover glass and two-component epoxy.

Room temperature DC and structural measurements

The room temperature characterization of perovskite solar cells was performed under simulated AM 1.5G light provided by a “Steuernagel Lichttechnik GmBH”, or Newport LCS-100 class ABB sun simulator, both calibrated using an ISE certified Si reference solar cell. Current density-voltage (J-V) scans were performed with a Keithley 2400 in forward and reverse directions, using a sweep speed of 85 mV s−1. Before measurement, the devices were light soaked in inert atmosphere for 30 min. The external quantum efficiency was measured without bias voltage and bias illumination, using a calibrated “Oriel QEPVSI-b” setup. Reflection was measured with a PerkinElmer UV-vis spectrometer, equipped with an integrating Ulbricht sphere and calibrated from an ISE certified white standard. Cross sectional scanning electron micrographs (SEM) were recorded with a Hitachi S-4100 at 5 kV acceleration voltage.

Low temperature DC and noise measurements

All the measurements, performed by varying the temperature, were carried out in a closed-cycle refrigerator, operating in the 8- to 300-K range. A computer-controlled feedback loop realized the temperature stabilization. The achieved stability, better than 1 K, was sufficient to record stable spectral data at all investigated temperatures, measured with a Cernox resistor thermometer in contact with the sample holder. The photovoltaic devices were biased with a low-noise Keithley DC current source. The DC voltage drop was measured with a digital multimeter, while the AC voltage signal, amplified with a low-noise PAR5113 preamplifier, was analyzed with a dynamic signal analyzer HP35670A. The presence of spurious components in the measured spectral traces was removed by resorting to a specific procedure, based on a sequence of four-probe and two-probe noise measurements40, useful to eliminate unwanted contact noise contributions41. A commercial cool white Light Emitting Diode (LED) was used as light source, for noise investigations. This choice of adopting a LED has been done in order to have a low-noise source and to discriminate intrinsic photoinduced mechanisms from extrinsic ones, potentially related to the complex electronics of the solar simulator.

Additional Information

How to cite this article: Barone, C. et al. Unravelling the low-temperature metastable state in perovskite solar cells by noise spectroscopy. Sci. Rep. 6, 34675; doi: 10.1038/srep34675 (2016).


  • Green, M. A., Ho-Baillie, A. & Snaith, H. J. The emergence of perovskite solar cells. Nature Photon. 8, 506–514 (2014).

    CAS  ADS  Article  Google Scholar 

  • (Year published: 2016) (Date access: –/–/2016).

  • Wehrenfennig, C., Eperon, G. E., Johnston, M. B., Snaith, H. J. & Herz, L. M. High charge carrier mobilities and lifetimes in organolead trihalide perovskites. Adv. Mater. 26, 1584–1589 (2014).

    CAS  Article  Google Scholar 

  • Wehrenfennig, C., Liu, M., Snaith, H. J., Johnston, M. B. & Herz, L. M. Charge-carrier dynamics in vapour-deposited films of the organolead halide perovskite CH3NH3PbI3−xCIx . Energy Environ. Sci. 7, 2269–2275 (2014).

    CAS  Article  Google Scholar 

  • Lang, F. et al. Radiation hardness and self-healing of perovskite solar cells. Adv. Mater. –, In press doi: 10.1002/adma.201603326 (2016).

  • Albrecht, S. et al. Monolithic perovskite/silicon-heterojunction tandem solar cells processed at low temperature. Energy Environ. Sci. 9, 81–88 (2016).

    CAS  Article  Google Scholar 

  • Lang, F. et al. Perovskite solar cells with large-area CVD-graphene for tandem solar cells. J. Phys. Chem. Lett. 6, 2745–2750 (2015).

    CAS  Article  Google Scholar 

  • Löper, P. et al. Organic-inorganic halide perovskite/crystalline silicon four-terminal tandem solar cells. Phys. Chem. Chem. Phys. 17, 1619–1629 (2015).

    Article  Google Scholar 

  • Bailie, C. D. et al. Semi-transparent perovskite solar cells for tandems with silicon and CIGS. Energy Environ. Sci. 8, 956–963 (2015).

    CAS  Article  Google Scholar 

  • Stranks, S. D. et al. Electron-hole diffusion lengths exceeding 1 micrometer in an organometal trihalide perovskite absorber. Science 342, 341–344 (2013).

    CAS  ADS  Article  Google Scholar 

  • Xing, G. et al. Long-range balanced electron- and hole-transport lengths in organic-inorganic CH3NH3PbI3 . Science 342, 344–347 (2013).

    CAS  ADS  Article  Google Scholar 

  • Loi, M. A. & Hummelen, J. C. Hybrid solar cells: Perovskites under the sun. Nature Mater. 12, 1087–1089 (2013).

    CAS  ADS  Google Scholar 

  • Marchioro, A. et al. Unravelling the mechanism of photoinduced charge transfer processes in lead iodide perovskite solar cells. Nature Photon. 8, 250–255 (2014).

    CAS  ADS  Article  Google Scholar 

  • Eames, C. et al. Ionic transport in hybrid lead iodide perovskite solar cells. Nature Commun. 6, 7497 (2015).

    CAS  ADS  Article  Google Scholar 

  • Divitini, G. et al. In situ observation of heat-induced degradation of perovskite solar cells. Nature Energy 1, 15012 (2016).

    CAS  ADS  Article  Google Scholar 

  • Even, J., Pedesseau, L. & Katan, C. Analysis of multivalley and multibandgap absorption and enhancement of free carriers related to exciton screening in hybrid perovskites. J. Phys. Chem. C 118, 11566–11572 (2014).

    CAS  Article  Google Scholar 

  • Yang, B. et al. Low threshold two-photon-pumped amplified spontaneous emission in CH3NH3PbBr3 microdisks. ACS Appl. Mater. Interfaces 8, 19587–19592 (2016).

    CAS  Article  Google Scholar 

  • Landi, G., Barone, C., De Sio, A., Pagano, S. & Neitzert, H. C. Characterization of polymer:fullerene solar cells by low-frequency noise spectroscopy. Appl. Phys. Lett. 102, 223902 (2013).

    ADS  Article  Google Scholar 

  • Barone, C., Landi, G., De Sio, A., Neitzert, H. C. & Pagano, S. Thermal ageing of bulk heterojunction polymer solar cells investigated by electric noise analysis. Sol. Energy Mater. Sol. Cells 122, 40–45 (2014).

    CAS  Article  Google Scholar 

  • Barone, C. et al. Probing transport mechanisms of BaFe2As2 superconducting films and grain boundary junctions by noise spectroscopy. Sci. Rep. 4, 6163 (2014).

    CAS  Article  Google Scholar 

  • Barone, C., Landi, G., Mauro, C., Neitzert, H. C. & Pagano, S. Universal crossover of the charge carrier fluctuation mechanism in different polymer/carbon nanotubes composites. Appl. Phys. Lett. 107, 143106 (2015).

    ADS  Article  Google Scholar 

  • Casaluci, S., Cinà, L., Matteocci, F., Lugli, P. & Di Carlo, A. Fabrication and characterization of mesoscopic perovskite photodiodes. IEEE Trans. Nanotechnol. 15, 255–260 (2016).

    CAS  ADS  Article  Google Scholar 

  • Chandni, U. & Ghosh, A. Simple kinetic sensor to structural transitions. Phys. Rev. B 81, 134105 (2010).

    ADS  Article  Google Scholar 

  • Barone, C. et al. Thermally and voltage activated excess 1/f noise in FeTe0.5Se0.5 epitaxial thin films. Phys. Rev. B 83, 134523 (2011).

    ADS  Article  Google Scholar 

  • Barone, C. et al. Electric field activated nonlinear 1/f fluctuations in Fe(Te, Se) superconductors. Supercond. Sci. Technol. 26, 075006 (2013).

    ADS  Article  Google Scholar 

  • Baikie, T. et al. Synthesis and crystal chemistry of the hybrid perovskite (CH3NH3)PbI3 for solid-state sensitised solar cell applications. J. Mater. Chem. A 1, 5628–5641 (2013).

    CAS  Article  Google Scholar 

  • D’Innocenzo, V. et al. Excitons versus free charges in organo-lead tri-halide perovskites. Nature Commun. 5, 3586 (2014).

    ADS  Article  Google Scholar 

  • Lin, Q., Armin, A., Nagiri, R. C. R., Burn, P. L. & Meredith, P. Electro-optics of perovskite solar cells. Nature Photon. 9, 106–112 (2015).

    CAS  ADS  Article  Google Scholar 

  • Burschka, J. et al. Sequential deposition as a route to high-performance perovskite-sensitized solar cells. Nature 499, 316–319 (2013).

    CAS  ADS  Article  Google Scholar 

  • McMeekin, D. P. et al. A mixed-cation lead mixed-halide perovskite absorber for tandem solar cells. Science 351, 151–155 (2016).

    CAS  ADS  Article  Google Scholar 

  • Saliba, M. et al. Cesium-containing triple cation perovskite solar cells: improved stability, reproducibility and high efficiency. Energy Environ. Sci. 9, 1989–1997 (2016).

    CAS  Article  Google Scholar 

  • Unger, E. L. et al. Hysteresis and transient behavior in current-voltage measurements of hybrid-perovskite absorber solar cells. Energy Environ. Sci. 7, 3690–3698 (2014).

    CAS  Article  Google Scholar 

  • Heo, J. H., Han, H. J., Kim, D., Ahn, T. K. & Im, S. H. Hysteresis-less inverted CH3NH3PbI3 planar perovskite hybrid solar cells with 18.1% power conversion efficiency. Energy Environ. Sci. 8, 1602–1608 (2015).

    CAS  Article  Google Scholar 

  • Kogan, S. Electronic Noise and Fluctuations in Solids (Cambridge University Press, Cambridge, 1996).

  • Huang, J., Shao, Y. & Dong, Q. Organometal trihalide perovskite single crystals: a next wave of materials for 25% efficiency photovoltaics and applications beyond? J. Phys. Chem. Lett. 6, 3218–3227 (2015).

    CAS  Article  Google Scholar 

  • Dong, Q. et al. Electron-hole diffusion lengths &gt;175 μm in solution-grown CH3NH3PbI3 single crystals. Science 347, 967–970 (2015).

    CAS  ADS  Article  Google Scholar 

  • Landi, G., Barone, C., Mauro, C., Neitzert, H. C. & Pagano, S. A noise model for the evaluation of defect states in solar cells. Sci. Rep. 6, 29685 (2016).

    CAS  ADS  Article  Google Scholar 

  • Barone, C., Pagano, S. & Neitzert, H. C. Transport and noise spectroscopy of MWCNT/HDPE composites with different nanotube concentrations. J. Appl. Phys. 110, 113716 (2011).

    ADS  Article  Google Scholar 

  • Jeon, N. J. et al. Solvent engineering for high-performance inorganic-organic hybrid perovskite solar cells. Nature Mater. 13, 897–903 (2014).

    CAS  ADS  Article  Google Scholar 

  • Barone, C. et al. Experimental technique for reducing contact and background noise in voltage spectral density measurements. Rev. Sci. Instrum. 78, 093905 (2007).

    CAS  ADS  Article  Google Scholar 

  • Barone, C. et al. Apparent volume dependence of 1/f noise in thin film structures: role of contacts. Rev. Sci. Instrum. 79, 053908 (2008).

    CAS  ADS  Article  Google Scholar 

Download references


S. Abate of CNR-SPIN Salerno is acknowledged for his valuable technical support. The authors are also grateful to O. Shargaieva for synthesis of CH3NH3I, and C. Klimm for recording SEM micrographs. A further acknowledgement is due to K. Mack from the Competence Centre Thin-Film- and Nanotechnology for Photovoltaics Berlin (PVcomB) for support in UV/VIS measurements.

Author information

Authors and Affiliations



C.B., C.M. and S.P. performed the electric noise measurements and the DC transport investigations by varying the temperature. The photovoltaic devices were prepared, optimized, and characterized at room temperature (under 1 sun illumination condition) by F.L., J.R., N.H.N. and B.R. C.B., S.P., G.L. and H.C.N. contributed to the theoretical interpretation of the experimental findings. All the authors were involved in the manuscript writing, discussing the results and the implications very accurately.

Ethics declarations

Competing interests

The authors declare no competing financial interests.

Electronic supplementary material

Rights and permissions

This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Barone, C., Lang, F., Mauro, C. et al. Unravelling the low-temperature metastable state in perovskite solar cells by noise spectroscopy. Sci Rep 6, 34675 (2016).

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI:

Further reading


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.


Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing