Abstract
In this research, the negative effective mass behavior of elastic/mechanical metamaterials is exhibited by a cantileverinmass structure as a proposed design for creating frequency stopping band gaps, based on local resonance of the internal structure. The massinmass unit cell model is transformed into a cantileverinmass model using the BernoulliEuler beam theory. An analytical model of the cantileverinmass structure is derived and the effects of geometrical dimensions and material parameters to create frequency band gaps are examined. A twodimensional finite element model is created to validate the analytical results and excellent agreement is achieved. The analytical model establishes an easily tunable metamaterial design to realize wave attenuation based on locally resonant frequency. To demonstrate feasibility for 3D printing, the analytical model is employed to design and fabricate 3D printable mechanical metamaterial. A threedimensional numerical experiment is performed using COMSOL Multiphysics to validate the wave attenuation performance. Results show that the cantileverinmass metamaterial is capable of mitigating stress waves at the desired resonance frequency. Our study successfully presents the use of one constituent material to create a 3D printed cantileverinmass metamaterial with negative effective mass density for stress wave mitigation purposes.
Introduction
Advancement made to the world of materials over the past few decades has brought on an era of uniquely engineered materials. The highest demand for performance of materials coupled by the fast pace of scientific developments have pushed boundaries beyond the imagination of man to design and engineer materials with exceptional properties not found in nature. An increasing amount of research has been conducted to explore the extraordinary physical effective properties (like negative effective mass density, negative effective elastic modulus and negative Poisson’s ratio, etc) of acoustic/elastic/mechanical metamaterials^{1,2,3,4,5}. Such properties are often realized through the fabrication of specifically designed structures at the meso, micro and nanoscale and not by material chemical composition. The potential applications of these unique metamaterials range from vibration isolation^{6,7,8}, acoustic sound wave control^{9,10,11}, impact and blastwave mitigation^{12,13,14}, etc. The wave attenuation and mitigation mechanism exhibited by the mechanical metamaterials is a result of the formation of frequency band gaps that prohibited transmission of acoustic/mechanical waves^{15,16,17,18,19}.
The control over band gaps in the negative effective mass concept employs a massinmass model which defines a unit cell with an outer mass and an inner mass connected by a spring^{20,21,22}. The system exhibits the dynamic negative mass behavior due to the internal resonance of the unit cell caused by the inner mass and the spring, as depicted in Fig. 1(a). The practical realization of these massinmass metamaterials remains a challenge, as they either represent cumbersome structures^{13,22}, or require more than one constituents for manufacturing (for example, heavy core as inner mass and surrounded by soft elastic layer, acting as spring)^{1,23}, which does not make fabrication easy, particularly if mass production of numerous unit cells is required in the entire structure.
The frequency band gaps of a metamaterial can also be controlled using phononic plates which employ beamlike resonators to induce local resonance^{24,25}. Other studies show wave attenuation in thin metamaterial plates as well as enhancements by introducing springboards^{26}. The plates are created using a cantilevermassmicrostructure, to analyze the dispersion relations for inplane longitudinal waves^{27}. Each design has proven to be effective at impact wave mitigation through the presence of band gaps, where the input frequency falls within the locally resonant band gap frequency of the internal structure. However, there is a lack of design parameters to govern the designed resonance frequency based on analytical model of cantileverinmass metamaterials. Moreover, the prototypes in earlier studies were typically made of metals^{25,27}, thus quick and easy fabrication could not be simply achieved.
Recent progress in threedimensional (3D) printing technology has enabled a rapid prototyping of complex models at a limited cost. Fabrication of metamaterials with complex internal architecture is a challenge in traditional manufacturing methodology. However, 3D printing offers possible realization of mechanical metamaterials, since in 3D printing, complex structural shapes and geometries can be achieved, without incurring assemblage and mold requirement and thus reducing cost and increasing efficiency in fabrication^{28}. Another manufacturing approach of elastic metamaterial is by the precision laser cutting system as demonstrated by Zhu et al.^{29}.
Early research conducted on the rapid prototyping of band gap microstructures revealed that it is possible to use modern 3D printing techniques to create features at a micro level. The outcome exhibits the formation of a frequency band gap in the material^{30}. In the effort to 3D print a massinmass metamaterial with springconnected mass, Buckmann et al.^{31} fabricated the delicate helical Hooke’s spring structures combined with the inner cube’s solid material, but realized that the springs are not smooth and have slightly larger than designed average wire diameter. Although 3D printing provides a lot of flexibility in design, it is still difficult to 3D print springs accurately. As such, there appears a need to reconsider the use of massinmass metamaterial model and possibly consider the better use of a cantileverinmass metamaterial design in 3D printing. The lack of analytical model based design and the need to achieve a one constituent material tunable mechanical metamaterial to enable easy fabrication by 3D printing are the main motivations for this work.
In this work, we propose the design, fabrication and characterization of 3D printable mechanical metamaterials by employing cantilever beamlike resonators to equivalently and effectively represent the spring massinmass model. We develop an analytical model of analogous cantileverinmass metamaterial based on BernoulliEuler beam theory. We perform parametric studies to understand and evaluate the influence of geometrical and material properties on the designed resonance bandgap of the metamaterials, with the aim to achieve tunability. We further validate the analytical model using 2D finite element simulation and investigate the wave attenuation performance of the metamaterial. Finally, we fabricate and demonstrate 3D printable metamaterials using Objet Eden260v 3D printer. We also conduct numerical experiments of the 3D printable metamaterials and validate the 2D simulation results and analytical model to confirm the feasibility of the design.
Results
Massinmass model
This section briefly reviews the theory of negative effective mass density obtained by using a massinmass spring system^{20,21}. Such a system would consist of an outer mass, m_{1} and an inner mass, m_{2} connected by a spring of stiffness k_{2}, as illustrated in Fig. 1(a). Assuming that the external applied force F and masses displacement u_{γ} (γ = 1, 2) are governed by harmonic motion, as in Equations (1) and (2), we can use the harmonic wave behavior to derive equations in terms of the applied force.
Applying Newton’s second law and free body diagram for each of the masses, we obtain the expressions for the forces acting on the mass m_{1} and m_{2}.
Outer mass, m_{1}:
Inner mass, m_{2}:
Solving the above equations using the harmonic wave behavior, we simplify to
where is the locally resonant frequency of the internal resonator.
We equate the motion of the outer mass to that of an effective mass, and use the free body diagram to derive an expression for the forces acting on the effective mass of the system.
Comparing Equations (5 and 6) yields the effective mass, , in terms of the locally resonant frequency of the structure, ω_{2} and the input frequency, ω.
From Equation (7), we see that as the input frequency ω gets close to locally resonant frequency ω_{2}, there is a vertical asymptote which approaches positive infinity from one side and negative infinity from the other. Within a certain range we observe a region where the effective mass of the system exhibits negative behavior, which is also the region where we see the formation of a frequency band gap.
Considering the stationary mass of the system as m_{st} = m_{1} + m_{2}, we derive the normalized mass as a function of the normalized operating frequency . Simplifying Equation (7), we have
We can see from Equation (8) that the normalized mass is a function of the normalized frequency and the term θ which is defined as the ratio of the inner mass to the outer mass, . Plotting the normalized mass against the normalized operating frequency, we observe the negative effective mass of the unit cell as presented in Fig. 1(b). The shaded region highlights the frequency domain where the effective mass is negative for θ = 1. We can see from Fig. 1(b) the effect of varying θ on the negative mass region. As the ratio of the inner mass to the outer mass increases, the frequency range for the negative effective mass of the unit cell also increases. For θ = 1 used in this study, the negative effective mass is in the region of ω_{2} < ω < 1.3ω_{2}.
Cantileverinmass model
We transform the spring massinmass model into a cantileverinmass model to observe the similar negative effective mass phenomenon. Since elastic structures behave like springs‒deflecting when a force is applied, the stiffness of a beam can be defined in the same way as for a spring. In the model depicted in Fig. 1(c), we use BernoulliEuler beam theory to find the deflection of the beam and its equivalent spring constant where Δ is the deflection in the spring or beam.
Linear spring:
Cantilever beam:
where v(x) is the transverse displacement function of beam length L and P is the applied load at the end of the beam (x = L).
The “spring constant”, k_{c} of a cantilever beam is derived in Equation (12), where is the Young’s Modulus of the beam, I_{z} is the moment of inertia about the bending zaxis [formula given in Fig. 1(d) for a rectangular cross section] and L_{eff} is the effective length of the beam. The equivalency of a massinmass unit cell with a cantileverinmass unit cell, is schematically presented in Fig. 1(c). Using the relationship and Equation (12), we can attain the resonance frequency of the cantileverinmass model as.
In the practical design displayed in Fig. 2(a), the resonator mass m_{2} is connected to a cantilever beam of length L_{3}, width h_{2} and thickness t. In order to simplify the approach, we assume the resonator mass to be a square defined by the dimension h_{1}. Given all the dimensions and assuming a one constituent material with density ρ, we have
We substitute Equations (14, 15, 16) into Equation (13) to obtain the resonance frequency in terms of the design parameters. It is important to note that the effective length of the beam L_{eff} is considered from the base to the center of the resonating mass, defined by Equation (16). This assumption was validated during parametric numerical study by varying beam length and comparing the resonance frequency evaluated numerically with that from the analytical model. As such, the resonance frequency of the cantileverinmass model with geometrical and material parameters is given by
It is interesting to note that due to the moment of inertia of the beam, I_{z} and the resonator mass, m_{2}, the resonance frequency of the cantileverinmass model is independent of thickness, t.
Factors influencing locally resonant frequency
Equation (17) can be expressed by the following notation showing the dependence of the resonance frequency on five variables.
These variables are considered and analyzed into two categories: geometric dimensions and material properties. We investigate how the geometric parameters and the material selection influence the locally resonant frequency of the structure in Fig. 2(b–d). We can observe from Fig. 2(b) that as the length of the beam increases, the resonance frequency decreases. Coupling with the effect of mass dimension, we see that as we increase h_{1}, there is a further decrease in the resonance frequency of the structure. This is directly correlated to the decrease in resonance frequency caused by the overall length of the beam, as the increase in dimension of the mass also increases the effective length of the beam, L_{eff}. In contrast, when you increase the width of the beam, h_{2} there is an increase in the resonance frequency, as shown in Fig. 2(c). Figure 2(b,c) demonstrate how the resonance frequency can be tuned and adjusted according to the geometrical parameters (h_{1}, h_{2}, L_{3}).
We also analyze the influence of material properties (E, ρ) on the designed resonance frequency. Figure 2(d) illustrates the effects of varying the Young’s modulus, and the material density, ρ. It is evident that as Young’s modulus increases, the resonance frequency increases as well. However, increasing the material density will decrease the resonance frequency of the cantileverinmass metamaterial. The material properties, influenced by the selection of materials, are particularly important in this work, as the material chosen must be able to be used in the 3D printer Objet Eden260v. The general application of the cantileverinmass analytical model can, however, be applied to any types of materials.
Band gap by frequency sweep
A twodimensional (2D) finite element (FE) model of the cantileverinmass structure was created in COMSOL Multiphysics to validate the derived analytical model. Further details of the 2D FE model should be referred to Methods Section. The frequency sweep result of the 2D FE model is shown in Fig. 3(a), comparing the design case 1 and case 2 (Table 1). In both of the designs we can see dips in the transmission ratio. The blue curve shows the frequency sweep for case 1 and a dip is observed at ω = 100 Hz. The red curve represents the frequency sweep for case 2 with a dip evident at ω = 277 Hz. In both cases, the results from the FE simulation have very good agreement with the designed resonance frequency predicted by the cantileverinmass analytical model Equation (17).
This dip in displacement ratio proves that there is energy reduction as the wave propagates through the metamaterial. According to the negative effective mass model explained in earlier section, as approaches the locally resonant frequency ω_{2} of the structure, the effective mass approaches positive infinity from one side and negative infinity from the other side. This phenomenon is clearly exhibited in the frequency sweep simulation.
It is worth noting that the band gap region for negative mass starts from the dip at the designed resonance frequency and ends when the transmission ratio returns to 1. Case 1 shows a narrower band gap region compare to Case 2. This is expected as the negative effective mass region is dependent on the locally resonant frequency (the region is ω_{2} < ω < 1.3ω_{2} for θ = 1 used in this study), so higher resonance frequency naturally has broader band gap region.
Fast Fourier Transform of internal resonator
Figure 3(b) displays the Fast Fourier Transform (FFT) of the first resonator in both design case 1 and case 2. FFT plot provides clear understanding of the vibrational frequency and energy absorption of the internal mass during wave propagation through the metamaterial. As defined by the negative effective mass of the analytical cantileverinmass model, the internal resonance of the metamaterial is caused by the beam and the resonating internal mass. FFT results presented in Fig. 3(b) clearly show that the resonance peaks of the internal mass correspond in good agreement with the frequency dips seen in frequency sweep results [Fig. 3(a)]. This means that the internal resonators are absorbing the wave propagation energy at their respective designed resonance frequency.
Wave attenuation at band gap region
The locally resonant frequency of the cantileverinmass structure results in the presence of frequency band gaps at the designed frequency region. As introduced in the massinmass model for negative effective mass, when the input frequency approaches the locally resonant frequency, the negative effective mass behavior is exhibited and this causes wave attenuation at the designed frequency. In order to observe wave attenuation at specific frequency input, we plot and compare the displacement of the 10^{th} unit cell (output) and 1^{st} unit cell (input). Figure 4(a) shows the result of the model without resonators (not a cantileverinmass metamaterial). It is clear that stress wave propagates through the material without any attenuation. For the model with resonators (cantileverinmass metamaterial with designed frequency at 277 Hz), three different harmonic input frequencies (according to Equation 18) are given for different cases. We can see that when the input frequency is within the passing band of the metamaterial [77 Hz and 477 Hz shown in Fig. 4(b–d)], waves propagate through the metamaterial without attenuation. However, when the input frequency falls within the stopping band gap of the cantileverinmass structure [277 Hz in Fig. 4(c)], significant wave attenuation is clearly observed.
For frequencies which are outside the band gap (passing band), we can see that the displacement at the 10^{th} unit cell is larger than the input. This is due to the reflection and interaction of the propagating stress waves. At passing band input frequency of 77 Hz, we observe a 24.8% increase in the average displacement. At 477 Hz input frequency, we notice a 16.5% increase in the average displacement of the unit cell. However, when the input frequency is within the stopping band region at 277 Hz, a huge reduction of 52.6% in the average displacement of the 10^{th} unit cell is achieved.
Band gap for 3D numerical experiment
According to the analytical model, the cantileverinmass structure should be independent of thickness. In order to validate this hypothesis, a 3D FE model was created and simulated. The 2D model was given a thickness of 1 centimeter to create the 3D model. A frequency sweep was performed from 0 to 500 Hz. Figure 5(a) reveals the transmission ratio at the 10^{th} unit cell across the frequency sweep. From the data gathered by the FE analysis, we observe a band gap forming around 260–350 Hz, resembling the frequency sweep result for the 2D model [Fig. 3(a)]. In order to validate wave attenuation performance, we plot the displacement profiles of 1^{st} unit cell (input) and 10^{th} unit cell (output) when the input frequency is around 277 Hz [Fig. 5(b)]. It is evident that significant wave attenuation occurs. Again the result obtained is very similar to the results from the 2D FE analysis [Fig. 4(c)]. The slight difference (of ~6%) in the frequency dip can be considered negligible and be attributed to the change in mesh size from the 2D model to a 3D model. The data acquired from the 3D simulation validates the assumption that the cantileverinmass analytical model is indeed independent of thickness, as well as provide numerical experiment demonstration for the cantileverinmass structure.
Realization of 3D printed metamaterials
The Objet Eden260v 3D printer was used to employ the photopolymerization technique to 3D print a prototype of the cantileverinmass structure using single material (one material constituent). Figure 6(a,b) present the ComputerAided Design (CAD) model and the prototype of the actual 3D printed part, thus demonstrating the realization of 3D printed cantileverinmass mechanical metamaterial. The authors plan to verify the analytical model of the cantileverinmass system using experimental data in the next phase of their research study. This will then provide a better understanding of the behavior of the structure in a practical scenario. The use of 3D printing and rapid prototyping will allow us to easily fabricate prototypes with different parameters and materials. We can switch from stiffer polymers such as VeroWhitePlus to more rubbery materials with very low Young’s modulus such as the TangoBlackPlus (E = 0.5MPa). 3D printing provides a valuable opportunity to explore a vast range of methods to fabricate 3D printable cantileverinmass mechanical metamaterial.
Discussion
In this work, we have derived the analytical model of a mechanical metamaterial by converting the massinmass model into a cantileverinmass model using the BernoulliEuler beam theory. The analytical model described by the parameters of the cantileverinmass structure demonstrated tunability of the designed resonance frequency by the influence of both geometrical dimensions and material parameters. A twodimensional finite element model is created to validate the analytical results. Frequency sweep results confirm the frequency band gap as predicted by the analytical model. The negative effective mass behavior of the metamaterial is also exhibited by significant wave attenuation when input frequency is within the stopping band region of the designed resonance frequency. When incoming waves are at frequencies of the passing band, no wave attenuation is observed.
To demonstrate application and feasibility for 3D printing, the cantileverinmass model is further employed to design and fabricate 3D printable mechanical metamaterial. A threedimensional numerical experiment is performed using COMSOL Multiphysics to validate the wave attenuation performance. Results show that the cantileverinmass metamaterial is capable of mitigating stress waves at the desired resonance frequency. This study successfully presents the use of one constituent material to create a 3D printed cantileverinmass metamaterial with negative effective mass density for stress wave mitigation purposes.
The flexibility of the cantileverinmass model will enable the design to be easily tuned and to achieve many different targeted resonance frequencies. In such a simply tunable model, it is more cost efficient to employ the use of 3D printing for the manufacturing of the cantileverinmass structure. With this control over the behavior of the metamaterial, we can design certain microstructures for other specific applications.
The authors believe that it is feasible to perform experimental testing on the 3D printed metamaterials. The input excitation can be created by an electrodynamic shaker and the output response of the metamaterial can be measured using Scanning Laser Doppler Vibrometry (SLDV) techniques to obtain the displacement and transmission ratio. The authors expect experimental testing data to agree well with numerical simulation results. However, the focus of this work is to derive an analytical model for the cantileverinmass metamaterial design, investigate its band gap tunability, demonstrate its 3D printability and validate the design and performance using numerical experiment. The authors hope to demonstrate experimental verification in the near future and share their results with the scientific research community.
It is worth noting that the cantileverinmass structure presented in this manuscript is the simplest and most fundamental design possible. Its complexity can be significantly increased by designing a cantilever head that best utilizes and optimizes the space within the outer mass, yet allowing enough room and freedom to vibrate according to specific application. Moreover, complexity of the structure can be enhanced by using multimaterials and 3D printing allows printing of multimaterials, such that it permits specific tuning of material properties for both the cantilever beam and resonator mass. Manufacturing using conventional technique might be cheaper under mass production, but specific tailoring of material structure and properties and fabrication of small number of complex parts is more economical by using 3D printing. It is true that nonmetal design has its disadvantage in load bearing and reliability. Depending on application, one option is to add a stronger material (metal) as a sacrificial plate when there is direct impact loading of high stress amplitude. Alternatively, one can use a relatively tough polymer that could be sufficient for load bearing purposes. The user has to make the decision on material selection based on design condition and application purposes. Nonetheless, this work proposes the analytical model for cantileverinmass model which could be employed for any materials.
Methods
Twodimensional (2D) finite element model
A twodimensional (2D) finite element (FE) model of the cantileverinmass structure was created in COMSOL Multiphysics to validate the derived analytical model and to prove the assumption that the resonance frequency is independent of thickness (Equation 17). We introduced two cases for the cantileverinmass structure, one at designed resonance frequency of 100 Hz and the other at 277 Hz (Table 1). The aim is to validate each design by comparing the designed resonance frequency (based on analytical model) and the dynamic wave attenuation performance of the system (based on FE simulation). The design parameters (listed in Table 1) were selected based on manufacturing feasibility and reasonable dimensional tolerance using 3D printing techniques. The material chosen in the FE simulation was VeroWhitePlus, which is a material type used in Objet Eden260v 3D printer and was subsequently fabricated by 3D printing. The material properties for VeroWhitePlus were taken from the data sheet provided (E = 2,500 MPa, v = 0.33, ρ = 1,170 kg/m^{3}).
A FE model was created for each design to find the frequency band gap using frequency sweep analysis across the model. The geometry for a unit cell was created in COMSOL Multiphysics and was set to an array of 50 unit cells as shown in Fig. 7(a). The boundary condition represented constraint of the base in the ydirection, with the input given in the xdirection at the first unit cell. Analysis of wave propagation through the model was performed. Figure 7(b) portrayed the finite element mesh of the model.
We provided an input and performed a frequency sweep function (from 0 to 500 Hz) to observe any band gap. The transmission ratio, defined by the ratio of the displacement at the 10th unit cell (output) over the displacement of the 1st unit cell (input), was analyzed. In order to confirm the presence of a band gap, a harmonic excitation was further applied at specific frequency input using Equation (18), where ω is the input frequency in hertz, with the aim to observe wave attenuation at band gap frequency.
Threedimensional (3D) finite element model
In order to validate that the analytical model for the designed resonance frequency of the cantileverinmass metamaterial is independent of its thickness, a 3D FE model was created with a thickness of t = 0.01 m. Other than having a tangible thickness, the 3D FE model resembles that of the 2D FE model with the same material properties, geometrical dimensions, boundary and input conditions. The 3D FE simulation of the model during stress wave propagation is shown in Fig. 7(c). Results were compared to that of the 2D FE model. The data obtained were used to validate the assumption that the cantileverinmass model is independent of thickness. The 3D FE model was created similarly using COMSOL Multiphysics 5.0. More importantly, the 3D FE model represented a numerical experiment that allowed us to use 3D printing to validate our analytical and computational results by gathering experimental data in the next phase of our study.
Fabrication using 3D printing
Based on the same design dimension as the 3D FE model, the feasibility of the design is demonstrated by 3D printing using the Objet Eden260v 3D printer, Stratasys Inc. The Eden260v is a commercialized 3D printer which makes use of the photopolymerization process to build a structure layer by layer. It makes use of photocurable polymers such as VeroWhitePlus which are sprayed by a nozzle onto the build path before being cured using ultra violet light.
Additional Information
How to cite this article: Qureshi, A. et al. Numerical investigation of band gaps in 3D printed cantileverinmass metamaterials. Sci. Rep. 6, 28314; doi: 10.1038/srep28314 (2016).
References
Liu, Z. et al. Locally resonant sonic materials. Science 289, 1734–1736 (2000).
Fang, N. et al. Ultrasonic metamaterials with negative modulus. Nature Mater 5, 452–456 (2006).
Hussein, M. I., Leamy, M. J. & Ruzzene M. Dynamics of phononic materials and structures: historical origins, recent progress and future outlook. ASME Appl. Mech. Rev. 66, 040802 (2014).
Jing, X., Meng, Y. & Sun, X. Soft resonator of omnidirectional resonance for acoustic metamaterials with a negative bulk modulus. Sci. Rep. 5, 16110 (2015).
Yasuda, H. & Yang, J. Reentrant origamibased metamaterials with negative Poisson’s ratio and bistability. Phys. Rev. Lett. 114, 185502 (2015).
Tan, K. T., Huang, H. H. & Sun, C. T. Optimizing the band gap of effective mass negativity in acoustic metamaterials. Appl. Phys. Lett. 101, 241902 (2012).
Finocchio, G. et al. Seismic metamaterials based on isochronous mechanical oscillators. Appl. Phys. Lett. 104, 191903 (2014).
Chen, Y. Y. & Wang, L. F. Bioinspired heterogeneous composites for broadband vibration mitigation. Sci. Rep. 5, 17865 (2015).
Guenneau, S., Movchan, A., Petursson, G. & Anantha Ramakrishna S. A. Acoustic metmaterials for sound focusing and confinement. New J. Phys. 9, 399 (2007).
Popa, B. I. & Cummer, S. A. Design and characterization of broadband acoustic composite metamaterials. Phys. Rev. B 80, 174303 (2009).
Zhang, S., Xia, C. & Fang, N. Broadband acoustic cloak for ultrasound waves. Phys. Rev. Lett. 106, 024301 (2011).
Tan, K. T., Huang, H. H. & Sun, C. T. Blastwave impact mititgation using negative efective mass density concept of elastic metamaterials. Int. J. Impact Eng. 64, 20–29 (2014).
Manimala, J. M., Huang, H., Sun, C. T., Synder R. & Bland S. Dynamic load mitigation using negative effective mass structures. Eng. Struct. 80, 458–468 (2014).
Chen, Y. Y. et al. Dissipative elastic metamaterials for broadband wave mitigation at subwavelength scale. Compos. Struct. 136, 358–371 (2016).
Huang, H. H. & Sun, C. T. Wave attenuation mechanism in an acoustic metamaterial with negative effective mass density. New J. Phys. 11, 013003 (2009).
Li, Y. et al. Enlargement of locally resonant sonic band gap by using composite platetype acoustic metamaterial. Phys. Lett. A 379, 412–416 (2015).
Ma, J., Hou, Z. & Assouar, B. M. Opening a large full phononic band gap in thin elastic plate with resonant units. J. Appl. Phys. 115, 093508 (2014).
Kim, E., Kim, Y. & Yang, J. Nonlinear stress wave propagation in 3D woodpile elastic metamaterials. Int. J. Solids Struct. 58, 128–135 (2015).
Chen, Y. Y. & Wang, L. F. Multiband wave filtering and waveguiding in bioinspired hierarchical composites. Ext. Mech. Lett. 5, 18–24 (2015).
Milton, G. W. & Willis, J. R. On modifications of Newton’s second law and linear continuum elastodynamics. Proc. R. Soc. A. 463, 855–880 (2007).
Huang, H. H., Sun, C. T. & Huang, G. L. On the negative effective mass density in acoustic metamaterials. Int. J. Eng. Sci. 47, 610–617 (2009).
Yao, S., Zhou, X. & Hu, G. Experimental study on negative effective mass in a 1D massspring system. New J. Phys. 10, 043020 (2008).
Lai, Y., Wu, Y., Sheng, P. & Zhang, Z. Q. Hybrid elastic solids. Nature Mater 10, 620–624 (2011).
Oudich, M., Li, Y., Assouar, B. M. & Hou, Z. A sonic band gap based on the locally resonant phononic plates with stubs. New J. Phys. 12, 083049 (2010).
Xiao, Y., Wen, J., Huang, L. & Wen, X. 2013. Analysis and experimental realization of locally resonant phononic plates carrying a periodic arry of beamlike resonators. J. Phys. D: Appl. Phys. 47, 045307 (2014).
Bilal, O. R. & Hussein, M. I. Trampoline metamaterial: Local resonance enhancement by springboards. Appl. Phys. Lett. 103, 111901 (2013).
Zhu, R., Huang, G. L., Huang, H. H. & Sun, C. T. Experimental and numerical study of guided wave propagation in a thin metamaterial plate. Phys. Lett. A. 375, 2863–2867 (2011).
Wang, K. et al. Designable dualmaterial auxetic metamaterials using threedimensional printing. Mater. Des. 67, 159–164 (2015).
Zhu, R., Liu, X. N., Hu, G. K., Sun, C. T. & Huang, G. L. Negative refraction of elastic waves at the deepsubwavelength scale in a singlephase metamaterial. Nature Communications 5, 5510 (2014).
Wanke, M. C. et al. Laser rapid prototyping of photonic bandgap microstructures. Science 275, 1284–1286 (1997).
Buckmann, T., Kadic, M., Schittny, R. & Wegener, M. Mechanical metamaterials with aniotropic and negative effective massdensity tensor made from one constituent material. Phys. Status Solidi B. 252, 1671–1674 (2015).
Acknowledgements
The authors gratefully acknowledge the Faculty StartUp Grant provided by The University of Akron.
Author information
Authors and Affiliations
Contributions
K.T.T. and A.Q. initiated the research; K.T.T. and A.Q. developed the theoretical models; A.Q. and B.L. performed the computation and analyzed the data; all authors contributed to the writing of the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Qureshi, A., Li, B. & Tan, K. Numerical investigation of band gaps in 3D printed cantileverinmass metamaterials. Sci Rep 6, 28314 (2016). https://doi.org/10.1038/srep28314
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep28314
This article is cited by

Metamaterials for simultaneous acoustic and elastic bandgaps
Scientific Reports (2021)

Numerical and Experimental Investigations on Tunable Lowfrequency Locally Resonant Metamaterials
Acta Mechanica Solida Sinica (2021)

Active control on topological immunity of elastic wave metamaterials
Scientific Reports (2020)

Wave attenuation and trapping in 3D printed cantileverinmass metamaterials with spatially correlated variability
Scientific Reports (2019)

Threedimensional resonating metamaterials for lowfrequency vibration attenuation
Scientific Reports (2019)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.