Infrasound may be used to detect the approach of hazardous volcanic mudflows, known as lahars, tens of minutes before their flow fronts arrive. We have analyzed signals from more than 20 secondary lahars caused by precipitation events at Fuego Volcano during Guatemala’s rainy season in May through October of 2022. We are able to quantify the capabilities of infrasound monitoring through comparison with seismic data, time lapse camera imagery, and high-resolution video of a well-recorded event on August 17. We determine that infrasound sensors, deployed adjacent to the lahar path and in small-aperture (10 s of meters) arrays, are particularly sensitive to remote detection of lahars, including small-sized events, at distances of at least 5 km. At Fuego Volcano these detections could be used to provide timely alerts of up to 30 min before lahars arrive at a downstream monitoring site, such as in the frequently impacted Ceniza drainage. We propose that continuous infrasound monitoring, from locations adjacent to a drainage, may complement seismic monitoring and serve as a valuable tool to help identify approaching hazards. On the other hand, infrasound arrays located a kilometer or more from the lahar path can be effectively used to track a lahar’s progression.
Lahar hazards and monitoring
In terms of number of lives lost, lahars are the most impactful of volcanic hazards over the last century. For example, the 1985 eruption of Nevado del Ruiz (Colombia) killed between 23,000 and 26,000 people when volcanic mudflows reached the flat valleys where the cities of Armero and Chinchina were located1,2. The catastrophe was particularly devastating given that the lahars originated near the summit and more than two hours before their arrival at Armero at about 70 to 75 km distance3,4,5. Functional early warning systems might have provided an opportunity for local communities to evacuate. In the wake of the Armero tragedy, lahar hazards have been recognized at many active, as well as dormant and extinct volcanoes. Many volcanoes in the Cascades Range, for example, have significant lahar hazards including Mount Rainier6 where large pre-historic flows occurring 500 and 5600 years ago have inundated currently heavily populated areas7. As of 2009, more than 78,000 people resided in Rainier’s lahar hazard zones8. Recognizing this risk, monitoring efforts by the United States Geological Survey have been implemented to integrate seismic and infrasonic early warning systems9. Integrated seismo-acoustic monitoring has previously been used elsewhere, for example in the European Alps to identify and monitor debris flows in non-volcanic regions10.
Geophysical monitoring at volcanoes is pertinent for eruption forecasting and detection of both syn-eruptive hazards (e.g., primary lahars) as well as surveillance of hazards unassociated with eruption (e.g., secondary lahars)11. Efforts to monitor lahar activity have traditionally focused on relatively high frequency (above 10 Hz) seismic measurements using geophones, referred to as acoustic flow monitors (AFMs12); detection of ground vibrations associated with passing mass movements have proven valuable for identifying the occurrence, duration, and relative size of mudflows and debris flows (e.g.13,14,15,16,17). Seismic monitoring of lahar channels at Fuego Volcano, using both short-period (above 1 Hz) and broadband seismometers, has already been implemented by the Guatemalan monitoring agency, the Instituto Nacional de Sismología, Vulcanología, Meteorología e Hidrología (INSIVUMEH; https://insivumeh.gob.gt/), to issue timely public bulletins of lahar activity. Their telemetered monitoring network permits near-real-time notice of lahars generally issued within tens of minutes of a flow’s passage at seismic sites, which at Fuego are situated near several drainages approximately 10 to 15 km from the summit. Flow occurrence is subsequently confirmed by first-hand observations or telemetered webcams. In general, high-frequency seismic waves produced by lahars appear to attenuate rapidly, which is why seismic lahar monitoring at Fuego has been installed adjacent to potential lahar channels and are particularly sensitive to local lahars as they pass by.
Lahars are known to advance at a range of speeds from a few meters per second (e.g.18,19,20) to several tens of meters per second (e.g.21,22), depending upon their size, composition (blocky, concentrated, or non-concentrated), and channel morphology (width, tortuosity and gradient)3. Given these velocities and location of lahar initiation zones, which is often high up on a volcano, timely alerts from AFMs and seismometers could be made reliably using upstream sensors to notify downstream communities of an approaching flow. This is not easily done at Fuego and other volcanoes, however, because logistics, access issues, and site maintenance are complicated higher up on the volcano. At Fuego Volcano, moderate-sized secondary lahars reaching populated areas (generally beyond 10 km) appear to travel with speeds of 4–8 m/s (18, this study). These relatively slow speeds imply that about two to four minutes of advance notice could be possible for each km of flow distance.
Our study of lahars is predicated on the concept that infrasound monitoring may complement seismic monitoring because it is capable of detecting the flows from a distance of many kilometers (e.g.22) and could thus be used to provide time sensitive alerts. Although seismic networks have demonstrated some potential for tracking distant lahar movements23, infrasound arrays have been shown to be particularly effective for identifying and tracking mass movements for a wide range of geophysical moving sources, including debris flows24, icefall and rockfall25,26, snow avalanches27, and pyroclastic density currents28. Here we compare lahar seismic signals with ‘broadband sound’ defined as extending from the near-infrasound band (1–20 Hz) into the low frequency audible band above 20 Hz. This study uses visual observations of flow characteristics, including timing and size, integrated with infrasound for a well-monitored event on August 17 using seismo-acoustic equipment and multiple cameras filming the flows. Following the analysis of this well-monitored flow, we then show that remote detection of relatively small mudflows using a single infrasound site is practical for an entire season of lahar activity using a catalog of more than 20 events from 2022.
We use Fuego Volcano (Guatemala) as a natural laboratory for lahar study given that it frequently produces rainy season lahars, particularly after eruptions that leave pyroclastic flow deposits within its active channels29. Typical Fuego eruptive activity includes small Strombolian to ash-rich eruptions, which deposit ash and tephra on the upper slopes, as well as sporadic larger eruptions, which emplace larger quantities of pyroclastic flow material in valley drainages during hours-to-days long paroxysms30,31,34. Recent paroxysms at Fuego include the disastrous June 3, 2018 event, which buried the community of San Miguel Los Lotes35, as well as more recent, but smaller, paroxysms occurring on March 7 and July 4, 2022. Ample material from the sporadic larger eruptions is available as a ready source of mud and hot debris, which contribute to the bulking materials for the frequent lahars occurring during Guatemala’s rainy season. Between June and October intense thunderstorms and rain events are common at Fuego and induce repeated secondary lahars similar to the activity observed at other frequently erupting monsoonal volcanoes, such as Merapi (Indonesia) and Colima (Mexico)32,33.
Experiment at Fuego volcano
Secondary lahars at Fuego, induced by rainfall, may be reliably observed during targeted short-duration field campaigns, which use proximal (< 100 m from lahar channel) sensors and distant (more than 1 km from channel) infrasound sensor arrays, seismic monitoring apparatus near the drainage, time lapse cameras, and time-synchronized video cameras and their audio channels. Most large drainages radiating from Fuego are active lahar paths; however, our 2022 experiment focused on the Ceniza drainage on the SSW side of the volcano (Fig. 1a) as it has been the most active channel during previous years, with dozens of events typically occurring during the four-month rainy season. Other drainages radiating from Fuego are also active lahar paths (e.g., Las Lajas18), however they are monitored locally and their activity is not readily detected by the Ceniza instrumentation.
Our experiment targeted Ceniza with instruments situated 6 to 16 km from the summit along the stream channel and included both campaign-style, short-term sensor deployments as well as data from the continuous long-term monitoring site known as FG14 (at 14.7 km channel distance from Fuego). The telemetered FG14 station is on the edge of Ceniza drainage and is operated by INSIVUMEH; in 2022 it consisted of a time lapse camera (CF), a 100-m aperture infrasound array (IF), and a short period vertical component seismometer (sF). Temporary stand-alone stations S4, S1, and S2 were broadband triaxial seismometers, while stations IO and IC were ~ 30-m-aperture, 3-element infrasound arrays with flat response between 0.1 and 100 Hz. All stations and sensors were located within 100 m of the channel except for station IO at the Fuego Observatory (1.3 km from the Ceniza channel’s closest approach). The highest concentration of sensors and cameras was situated between 13.5 and 16 km channel distance (inset in Fig. 1a) and included both INSIVUMEH’s time lapse camera CF at FG14 (recording at 40-s intervals) as well as two wide-angle high-definition video cameras at CB and CR recording at 25 frames per second (Fig. 2; Table 1).
The Ceniza drainage near FG14 (at 12 to 16 km) is usually a nearly dry flat-bottomed wash (~ 30–50 m wide) with ankle-to-knee-deep slow-moving water in braided channels (3–5 m wide); however, this stream can change rapidly and dramatically during precipitation events, which occur during common thunderstorms from May through October and often in the late afternoon. Between April 19 and October 13, 2022, at least 35 lahars occurring in Ceniza were reported in bulletins by INSIVUMEH of which approximately 22 occurred during daylight hours and with good webcam observations. These events’ sizes are determined by local observers who combine visual assessment of width and depth of flow, size and number of blocks transported, as well as amplitude and duration of seismic amplitudes at station sF (FG14). During the daylight hours in the 2022 season 14 Ceniza events were characterized as moderate-to-strong (fuerte), 4 as moderate (moderado), 14 as weak-to-moderate, and 3 as weak (debil). These lahar sizes are assessed qualitatively by INSIVUMEH analysists who ranked their size primarily based on seismic amplitudes at sF rather than by the visual observations. The largest of these flows occupy much of Ceniza’s channel when they pass the timelapse camera at CF at a distance of 14.7 km.
We organized our field campaign and sensor deployment in late August 2022 to coincide with anticipated intense lahar activity and had the expectation of approximately two events occurring each week. Our full suite of monitoring instrumentation was in place at Ceniza before August 17 (Fig. 1b) when a high quality, rain-induced event occurred that was ranked by INSIVUMEH staff as moderate. We first analyzed the event with the three-element infrasound array (IO) located at Fuego’s observatory to detect and track coherent sound in the 1 to 100 Hz filtered sound band. Our strategy for this distant array was to identify a moving source and track its progression using signal cross-correlation analysis with overlapping 5-s time windows and 1-s time steps (e.g.22,36, “Methods”). This event was relatively easy to analyze because thunderstorm activity, which can produce high-amplitude transients that can obscure lahar infrasound signal37, was relatively minor on August 17.
Using the onset of sustained highly correlated signal as a detection, the first indications of a lahar at IO was at 13:52 local time (19:52 UTC) (time A in Fig. 1b) and coincides with sound originating from Ceniza between channel distance 8 and 9 km. Its source within the Ceniza drainage is located by matching the expected infrasound time lags, for all candidate locations within the channel, with cross-correlation lag times calculated from the infrasound data recorded by the array (refer to section on “Methods” for more details). Evolving source locations, notable event times, and transitions in the inferred location within Ceniza are summarized in Table 2. For example, at 14:06 (time B) the source of infrasound appeared to migrate downstream towards a region around 11 to 12 km. At times C, D, and E the lahar successively crosses the field-of-view of cameras CB, CF, then CR after which infrasound source detection returns to the region between 8 and 9 km. We note that infrasound signal amplitude and coherence taper by 15:11 (time F) about 80 min after first lahar signal detection. Following time F the detectable infrasound from downstream reaches of Ceniza’s channel remains apparent for several hours. We attribute this non-lahar acoustic signal to turbulent stream features and concentrated flow, which has been shown to radiate infrasound in fluvial environments (e.g.38).
Time elapsed between flow front arrivals and distance difference between the C and E cameras are used to compute an average flow speed of 4.2 m/s for the initial lahar head for the August 17 event. This corresponds to a 7.1-min transit time for the 1.8 km channel transect. Average speed in this section of the channel appears relatively slow compared to some published lahar speeds (e.g.21,22), however it is in line with cited values from smaller secondary lahars elsewhere at Fuego18 and in some other studies where secondary lahars are common, e.g., at Colima and Popocatepetl16,19. The slow flow speed may be attributed to the relatively low gradient between cameras CB and CR, which drops less than 100 m per km.
Interpretation of Lahar infrasound
Lahar infrasound signals are long in duration and appear tremor-like, emerging gradually and decaying even more slowly (e.g.22.). Infrasound recordings from the featured lahar on August 17 appear ‘noisy’ at IO in the sense that the signal is punctuated by high amplitude short-duration pulses, which correspond to two types of transient events including: (1) repeated thunder, which is a spatially-distributed broadband source (e.g.37,39.), and (2) explosive Strombolian activity, which is sourced at Fuego’s vent and has a median frequency value less than 10 Hz (e.g.40). These volcano and thunder signals can ‘contaminate’ lahar signal and impede signal detection, however they can also be identified and excluded given their high-amplitude, short-duration transient nature (refer to Fig. 1b and discussion of thunder and explosion classification in “Methods”). Visual review of the cross-correlation analyses is particularly effective as a tool to identify the lower amplitude tremor-like lahar signals because correlations from these flow signals are extended in time duration and have either gradually-varying or static time lags (see red dashed lines in Fig. 3a). Cross-correlation signal detection is a powerful tool even when infrasound is obscured by incoherent wind noise, which was significant at station IO, where two of three sensors had to be located on the observatory rooftop.
The observatory infrasound array IO, which is situated 1.3 km from Ceniza’s closest approach, is used primarily to identify the lahar onset and to track the movement of an initial energetic flow pulse, which is a common feature for many lahars manifested as a head wave (e.g.20,41.). We note however that once the initial surge propagates sufficiently far downstream the IO array becomes preferentially sensitive to proximal sources occurring in the closest section of the channel. This is most notable as the August 17 flow begins to ebb (shortly after time E) and the primary infrasound source location appears to return to 9 to 10 km along the channel. One of the challenges of tracking lahars, or other types of mass movements (e.g., rockfalls, debris flows, or pyroclastic density currents42), is that sound sources are distributed over large spatial extents and are long-duration lasting tens of seconds to hours. Their non-compact sources are dynamic in size and source position such that different stations may be sensitive to different sections of a flow path. Another challenge is that the lahar generation process is non-instantaneous and may occur over an extended spatial region producing multiple flow surges18, which may or may not coalesce43.
Infrasound detections from arrays located immediately adjacent to the Ceniza drainage at IC and IF show different patterns of lag time evolution compared to IO (Figs. 3a, 4e,f) and they can not generally be used to pinpoint a sound source position within the channel. They can, however, be used to detect lahar sources originating both upstream and/or downstream. For example, both the IC and IF arrays indicate strongly correlated sound beginning soon after time A. This strong signal correlation ends abruptly at times C and D when the flow front reaches the cameras that are co-located with the respective arrays. Thereafter, faint coincident dual sources become evident in the correlation analysis pointing to signals originating from both upstream and downstream azimuths. Coherent sources are detected because these distributed regions of the drainage are filled with flowing debris creating a superposition of sound, which share a common incidence. Because the river geometry is nearly straight for long segments there tends to be strong detections originating from the two distinct directions. In contrast, those acoustic sources in the river adjacent to the arrays do not produce coherent signal because they bombard the array from a wide range of azimuths. This observation is relevant for informing the situation of near-channel infrasound monitoring arrays. Tracking of moving flow sources is generally improved if the array is deployed more than a few hundred meters from the channel and if the array aperture is small relative to the distance between array and lahar source (e.g.18.). Array IO, for instance, is effective for tracking a moving flow source, whereas arrays IC and IF may be better suited for early detections.
The early detection of the lahar with both IC and IF is notable and testament to the remote sensing capabilities of an infrasound monitoring system that is situated at river’s edge and below an extended section of relatively straight channel. This array topology permits detection of 22 min of very clear precursory infrasound prior to the flow’s physical arrival for the August 17 event. Assuming that the flow front advances no slower than 4.2 m/s (and likely faster higher up on the volcano) a 22-min precursor implies that the initial lahar signal detection is associated with a source at least 5.5 km upstream. This coincides with an origination zone less than 8 to 9 km channel distance and in the region where IO first picks up the moving source at time A. This section of the channel also coincides with the inferred depositional region for the July 4, 2022 pyroclastic density current, which likely served as an important source of material that could have contributed to bank collapse and rapid flow bulking. Hot debris is evidenced by the steaming mud and blocks that are visually evident in video about five minutes after the initial flow’s arrival.
Seismic and broadband acoustics
The 22-min lahar sound precursor is dominated by acoustic energy concentrated in the infrasound band, but its frequency content increases noticeably as the flow approaches (Fig. 4b). At around 3 min prior to the flow’s arrival the median frequency increases and crosses into the audible range (above 20 Hz). This frequency shift coincides with an inferred flow front located about 1 km upstream from the monitoring array. Once the flow has arrived the median frequency remains relatively constant at 30 to 35 Hz. Notably, the audible-band sound extracted from cameras CB and CR is only evident as the flow arrives and afterwards (Fig. 4a). Although Fuego observatory staff report that sounds originating from an approaching lahar are common, we conclude that the audible warning precursor is likely only useful as a few tens of seconds warning. Our spectral observations point definitively to the benefit of broadband sound monitoring and early detections of lahars using the infrasound band.
As with infrasound, the seismic spectral content (Fig. 4c) also shows a similar, albeit less pronounced, rising evolution in its frequency content beginning several minutes prior to the arrival of the lahar. Between times C and E the median spectral content of the seismic tremor increases from 6 to 8 Hz and then remains relatively constant. At present we are unable to determine whether the seismic signal is dominated by ground-propagating seismic waves, air-to-ground coupled sound, or a combined-influence seismo-acoustic wavefield.
Both seismic and infrasound channels indicate precursory wave energy reaching IC, IF, and sF well prior to the lahar’s arrival (Fig. 4d). In both infrasound and seismic wavefields the signals are emergent and hard to discern by viewing a linearly scaled pressure or velocity time series; the precursors become more evident following conversion of the waveform signals to power, removal of high amplitude transients (thunder and explosions) using median filters, and displaying in decibels or using logarithmic axes. For the August 17 event, both infrasound and seismic power are identifiable by about 14:00, which is at least 15 min prior to the arrival of the flow at station IF and sF and only a few minutes after cross correlation analysis initial detections (Fig. 4e,f). Following the flow’s arrival there are fluctuations in seismo-acoustic power evident in the logarithmically-scaled displays (Fig. 4d), which are likely associated with oscillating flow levels or small surges similar to those described at Fuego by18. For the August 17 event these pulses correspond to relatively small surges lasting only a few minutes and are evident in the videos from CB and CR (viewable at https://www.youtube.com/watch?v=O9lJT52MVik and at data repository—see Data availability).
Ensemble analysis and utility of infrasound for early warning of Lahars
With lessons learned from the August 17 lahar, we analyzed 22 events occurring in 2022 that were well recorded with the telemetered station FG14 (i.e., sF, IF, and CF) and occurred during daylight hours (Table 3). We performed the same correlation analysis on channels 1 and 3 of array IF that was done in Fig. 4f to highlight the monitoring capabilities of using just two microphones for detections. We then used timelapse video to identify an initial lahar flow surge, which is a common feature of most of Fuego’s secondary lahars in Ceniza. We note that for those events where streamflow is already elevated a definitive lahar flow front surge is sometimes less apparent. INSIVUMEH recognizes these events, which begin gradually in terms of their seismic signature, as correntadas, or currents. Visually, they begin as river flows and do not initially convey large bulky bed load.
Although featured lahar sizes are variable and infrasound signal quality was affected by a wide range of noise (thunder being most pernicious), decent lahar precursors were identifiable in 18 of 22 events (see Table 2 and videos linked at https://www.youtube.com/watch?v=wfzVMHiPI2o in Additional Information). For those four events occurring on August 12, August 24, October 2, and October 13, clear precursors were not evident; we consider that infrasound noise may have been especially high and/or the flow head might not have arrived as a significant surge. Lahars that increase gradually and/or begin as correntadas tend not to present as highly coherent upstream sources because the sound adjacent to the station from low-level fluvial activity is ongoing and/or may dominate.
The observation of strong, easy-to-identify infrasound precursors for flows that begin with a surge is auspicious for monitoring purposes. These are the flows that are potentially the most damaging because they have the capability to arrive suddenly and surprisingly with an energetic lahar head. Some of the larger 2022 lahars exhibit infrasound precursors as long as 30 min detected at FG14. This length of time could avail itself to timely warnings once automated systems are developed. We suspect that in these cases the detected lahar sounds are being picked up in a zone as far away as 7 km above the infrasound array and in the vicinity of 7 to 8 km channel distance. Detections in these locations, if relayed as social media alerts, could allow timely evacuation of downstream locations where vehicles and/or people typically cross the channel.
We propose that infrasound monitoring is an important complement to co-located seismic monitoring. In the case of the Ceniza drainage INSIVUMEH uses ground vibrational tremor amplitudes to successfully issue alerts of a lahar in progress and these are produced with a high degree of reliability and generally less than 10 to 20 min after the lahar has passed FG14. Seismic sensors situated higher up in Ceniza would be capable of definitively detecting earlier lahar movement—at around the same time that downstream infrasound arrays begin to identify flows—however their situation and maintenance high up on the volcano is logistically complicated and costly.
Lahars similar in size to those shown in Table 3 have been frequently recurring at Fuego since the current cycle of activity began in 1999. Although these mudflows are much smaller than the primary lahars at Nevado del Ruiz1, Mount St. Helens3, or Villarrica22, they represent a persistent seasonal hazard for the many road crossings (fords) at active channels, where incidents of vehicles caught by lahars have happened over the last few years. Advanced notice of lahars approaching the crossing points could allow timely closing of the road traffic to avoid such incidents in the future. An important question then becomes how and where to configure seismo-acoustic sensors in the most efficient topology given finite hardware resources and the often-difficult access and maintenance of upstream locales.
The capabilities of infrasound as a lahar monitoring tool are evident for infrasound sensors used in array configuration with as few as two sensors. Application of cross-correlation analysis for sensors spaced 30 to 50 m apart makes it possible to discriminate noise and detect signals originating from upstream sources that combine constructively and reach the sensor array with a consistent direction. Lahar sound distributed along a straight river path can thus ‘pile up’ and be used to identify the onset of subtle or emergent infrasound. Infrasound arrays situated a distance away from the lahar flow path may not be as sensitive to detection of low signal-to-noise infrasound, but they do have the benefit of detecting flow movement reflected by shifting cross correlation time lags and a systematic change in the direction of incident sound; in order to track lahar movements situation of infrasound arrays set back from the lahar channel is thus recommended. Although the lahars featured in this study are small compared with the large primary lahars of Armero (Colombia) in 19851, Mount St. Helens (US) in 198021, or Villarrica (Chile) in 201522, the infrasound radiation is still sufficient to identify an approaching flow even in the presence of substantial background noise. This work contributes to the growing field of environmental seismology42, which has a focus on gravity-driven mass movement and is increasingly making use of both ground-propagating seismic as well as atmosphere-propagating infrasound wavefields. Lahar seismo-infrasound is an example of a geophysical discipline where scientific study and hazard monitoring objectives are closely intertwined.
Data from three-element infrasound mini-arrays were analyzed at stations IO, IC, and IF (where three of the four permanent microphones were utilized). Data were recorded at IO and IC with infraBSU version #2 microphones and DiGOS Datacube 24-bit dataloggers, and with Chapparal microphones and radio telemetry at IF. All data were recorded at 200 Hz (IO and IC) or upsampled from 50 to 200 Hz (at IF) prior to application of a high pass, two-pole 1 Hz filter. More information on the technical specifications and operations of the infraBSU infrasonic microphones can be found in44. Precision relative locations of infrasound sensors is important for array analysis and positional information at IO and IC were surveyed using mapping grade Emlid Reach RS2 GPS. All infrasound waveform data were recorded with a common GPS-enabled clock, which is a feature of the respective digitization systems. The timing of the stand-alone camera video is accurate to within 1 s confirmed by regularly filming of a cell phone digital clock.
Time delays between sound arriving at microphones can be used to extract sound location information from each array (e.g., Fig. 3a). In each time window where correlated time signal is identified the peak correlation lag times are calculated and used to determine the most likely location for the incident sound. From the array data at IO the locations of possible sources were inferred based upon the expected lag times for sources confined to Ceniza’s channel, the known array sensor positions, and an assumed speed of 343 m/s. The channel path of candidate source locations was derived from 8-m resolution digital topography produced after the June 3, 2018 paroxysm by the UN-SPIDER project. The channel was drawn from the summit using a steepest gradient descent in to the Ceniza drainage. Channel distances shown in Fig. 1b are relative to the summit and mapped to time lags at IO such that each discrete time lag corresponds to a distance along Ceniza (Fig. 3a). Forward azimuths for these sources are indicated parenthetically. Assuming a lahar in Ceniza it is thus possible to locate a dominant source with only one pair of sensors, but multiple sensor pairs can be used to corroborate locations. Uncertainty in channel location may be calculated as positional uncertainty for a given cross-correlation time lag variability. We compute an uncertainty ε in terms of km/sample. The inverse, or positional precision, is indicated in Fig. 3c and shows best precision for lahars located between 8 and 11 km. Sensor pairs for channels 3 and 2 and 1 and 3 have better precision than sensor pair 2 and 1 because their orientation is sub-parallel to the drainage. This technique for locating position in Ceniza is the same as that utilized for a lahar occurring at Villarrica Volcano (Chile) in 201522.
Thunder and volcanic vent activity, considered as noise in this study, are identified as short-duration highly-correlated transient events lasting less than 1 min (e.g., Figs. 1b, 4e,f). Nearly all lahar infrasound events from Table 3 have varying amounts of thunder and volcano infrasound, which are identified by calculating a ratio of short term (5 s) to long-term (60 s) average power. We identify and label these transients when the short-term long-term ratio exceeds a threshold value of 3 for events separated by 30 s or more. These values are arbitrary, but work well to identify discrete events, which look to be eruptions or thunder during visual review. We then classify thunder and eruption infrasound based upon their distinct spectral content in the 1 to 100 Hz band. Those events with 50% of their energy below 20 Hz are found to be volcanic in origin, while those with 50% of energy above 20 Hz are categorized as thunder. During the six-hour record of infrasound activity on August 17 transient detections included 30 eruption events and 65 thunder signals (Fig. 1b).
Waveform data for the 17 August event are provided as MATLAB files at Boise State University’s Infrasound Data Repository (https://scholarworks.boisestate.edu/infrasound_data/). These data, along with a README text file, are archived as Dataset for Infrasound Early Warning Detections for Lahars with a dedicated https://doi.org/10.18122/infrasound_data.10.boisestate. Time lapse video and camera footage of the featured lahars are at this repository following publication. They are also posted as YouTube videos (https://www.youtube.com/watch?v=wfzVMHiPI2o and https://www.youtube.com/watch?v=O9lJT52MVik).
Lowe, D. R. et al. Lahars initiated by the 13 November 1985 eruption of Nevado del Ruiz, Colombia. Nature 324, 51–53 (1986).
Pierson, T. C., Janda, R. J., Thouret, J.-C. & Borrero, C. A. Perturbation and melting of snow and ice by the 13 November 1985 eruption of Nevado del Ruiz, Colombia, and consequent mobilization, flow and deposition of lahars. J. Volc. Geotherm. Res. 41, 17–66 (1990).
Pierson, T. C. An empirical method for estimating travel times for wet volcanic mass flows. Bull. Volc. 60, 98–109 (1998).
Huggel, C., Ceballos, J. L., Pulgarĺn, B., Ramírez, J. & Thouret, J.-C. Review and reassessment of hazards owing to volcano–glacier interactions in Colombia. Ann. Glac. 45, 128–136 (2007).
Künzler, M., Huggel, C. & Ramírez, J. M. A risk analysis for floods and lahars: Case study in the Cordillera Central of Colombia. Nat. Hazards 64, 767–796 (2012).
Diefenbach, A. K., Wood, N. J. & Ewert, J. W. Variations in community exposure to lahar hazards from multiple volcanoes in Washington State (USA). J. Appl. Volc. 4, 1–14 (2015).
George, D. L., Iverson, R. M. & Cannon, C. M. Modeling the Dynamics of lahars that Originate as Landslides on the West Side of Mount Rainier (U.S. Geological Survey, 2022). https://doi.org/10.3133/ofr20211118(2022).
Wood, N. & Soulard, C. Variations in population exposure and sensitivity to lahar hazards from Mount Rainier, Washington. J. Volc. Geotherm. Res. 188, 367–378 (2009).
Monitoring Lahars at Mount Rainier. United States Geological Survey. https://www.usgs.gov/volcanoes/mount-rainier/monitoring-lahars-mount-rainier (2022)
Schimmel, A., Hübl, J., McArdell, B. W. & Walter, F. Automatic identification of alpine mass movements by a combination of seismic and infrasound sensors. Sensors (Switzerland) 18, 1–19 (2018).
Smith, G. A., & Lowe, D. R. Lahars: Volcano-hydrologic events and deposition in the debris flow—Hyperconcentrated flow continuum. in Sedimentation in Volcanic Settings (Fisher, R. & Smith, G. A. Eds.). 59–70 (SEPM Society for Sedimentary Geology, 1991).
LaHusen, R. G. Acoustic Flow Monitor System—User Manual. Open-File Report 2002-429. https://pubs.er.usgs.gov/publication/ofr2002429 (U.S. Geological Survey, 2002)
Marcial, S. S., Delos Reyes, P. I., Chu, A. V., & Solidum, R. U. Instrumental lahar monitoring of Mt. Pinatubo. in Fire and Mud: Eruption and Lahars of Mt. Pinatubo, Philippines (Newhall, C. G. & Panongbayan, R. S. Eds.). 1015–1022 (University of Washington Press, 1993).
Lavigne, F. et al. Instrumental lahar monitoring at Merapi Volcano, Central Java, Indonesia. J. Volc. Geotherm. Res. 100, 457–478 (2000).
Coviello, V., Capra, L., Vázquez, R. & Márquez-Ramírez, V. H. Seismic characterization of hyperconcentrated flows in a volcanic environment. Earth Surf. Proc. Land. 43, 2219–2231 (2018).
Vázquez, R., Suriñach, E., Capra, L., Arámbula-Mendoza, R. & Reyes-Dávila, G. Seismic characterisation of lahars at Volcán de Colima, Mexico. Bull. Volc. 78, 1–14 (2016).
Hürlimann, M. et al. Debris-flow monitoring and warning: Review and examples. Earth Sci. Rev. 199, 102981 (2019).
Bosa, A. et al. Tracking secondary lahar flow paths and characterizing pulses and surges using infrasound array networks at Volcán de Fuego, Guatemala. Volcanica 4, 239–256 (2021).
Muñoz-salinas, E., Manea, V. C., Palacios, D. & Castillo-rodriguez, M. Estimation of lahar flow velocity on Popocatépetl volcano (Mexico). Geomorphology 92, 91–99 (2007).
Lube, G. et al. Energy growth of laharic mass flows. Geology 40, 475–478 (2012).
Pierson, T. C. Initiation and flow behavior of the 1980 Pine Creek and Muddy river lahars, Mount St. Helens, Washington. Geol. Soc. Am. Bull. 96, 1056–1069 (1985).
Johnson, J. B. & Palma, J. L. Lahar infrasound associated with Volcán Villarrica’s 3 March 2015 eruption. Geophys. Res. Lett. 42, 6324–6331 (2015).
Kumagai, H., Palacios, P., Maeda, T., Castillo, D. B. & Nakano, M. Seismic tracking of lahars using tremor signals. J. Volcanol. Geotherm. Res. 183, 112–121 (2009).
Kogelnig, A., Hübl, J., Suriñach, E., Vilajosana, I. & McArdell, B. W. Infrasound produced by debris flow: Propagation and frequency content evolution. Nat. Hazards 70, 1713–1733 (2014).
Marchetti, E., Walter, F. & Meier, L. Broadband infrasound signal of a collapsing hanging glacier. Geophys. Res. Lett. 48, e2021GL093579 (2021).
Johnson, J. B. & Ronan, T. J. Infrasound from volcanic rockfalls. J. Geophys. Res. Solid Earth 120, 8223–8239 (2015).
Watson, L. M., Carpenter, B., Thompson, K. & Johnson, J. B. Using local infrasound arrays to detect plunging snow avalanches along the Milford Road, New Zealand (Aotearoa). Nat. Hazards 111, 949–972 (2022).
Yamasato, H. Quantitative analysis of pyroclastic flows using infrasonic and seismic data at Unzen volcano, Japan. J. Phys. Earth 45, 397–416 (1997).
Venske, E. Fuego (342090) in [Database] Volcanoes of the World (v. 5.0.0; 1 Nov 2022). Global Volcanism Program, Smithsonian Institution https://volcano.si.edu/volcano.cfm?vn=342090 (2022)
Lyons, J. J., Waite, G. P., Rose, W. I. & Chigna, G. Patterns in open vent, strombolian behavior at Fuego volcano, Guatemala, 2005–2007. Bull. Volc. 72, 1–15 (2010).
Wolf, R. P. E. Volcanic processes and human exposure as elements to build a risk model for Volcan de Fuego, Guatemala. Doctoral Dissertation, Michigan Technological University (2013).
Lavigne, F. et al. Instrumental lahar monitoring at Merapi Volcano, Central Java, Indonesia. J. Volcanol. Geotherm. Res. 100, 457–478 (2000).
Capra, L., Coviello, V., Borselli, L., Márquez-Ramírez, V.-H. & Arámbula-Mendoza, R. Hydrological control of large hurricane-induced lahars: Evidence from rainfall-runoff modeling, seismic and video monitoring. Nat. Hazards Earth Syst. Sci. 18, 781–794 (2018).
Naismith, A. K. et al. Eruption frequency patterns through time for the current (1999–2018) activity cycle at Volcán de Fuego derived from remote sensing data: Evidence for an accelerating cycle of explosive paroxysms and potential implications of eruptive activity. J. Volc. Geotherm. Res. 371, 206–219 (2019).
Ferrés, D., & Escobar-Wolf, R. Informe Técnico: Volcán de Fuego. (Accion Contra el Hambre, 2018).
Johnson, J. B., Anderson, J. F., Marshall, H. P., Havens, S. & Watson, L. M. Snow avalanche detection and source constraints made using a networked array of infrasound sensors. J. Geophys. Res. Earth Surf. 126, 1–23 (2021).
Johnson, J. B. et al. Imaging thunder. Geophys. Res. Lett. 38, L19807 (2011).
Schmandt, B., Aster, R. C., Scherler, D., Tsai, V. C. & Karlstrom, K. Multiple fluvial processes detected by riverside seismic and infrasound monitoring of a controlled flood in the Grand Canyon. Geophys. Res. Lett. 40, 4858–4863 (2013).
Anderson, J. F., Johnson, J. B., Arechiga, R. O. & Thomas, R. J. Mapping thunder sources by inverting acoustic and electromagnetic observations. J. Geophys. Res. Atmos. 119, 13287–13304 (2014).
Diaz-Moreno, A. et al. Characterization of acoustic infrasound signals at Volcán de Fuego, Guatemala: A baseline for volcano monitoring. Front. Earth Sci. 8, 549774 (2020).
Doyle, E. E., Cronin, S. J. & Thouret, J. C. Defining conditions for bulking and debulking in lahars. Bull. Geol. Soc. Am. 123, 1234–1246 (2011).
Allstadt, K. E. et al. Seismic and acoustic signatures of surficial mass movements at volcanoes. J. Volc. Geotherm. Res. 364, 76–106 (2018).
Doyle, E. E., Cronin, S. J., Cole, S. E. & Thouret, J.-C. The coalescence and organization of lahars at Semeru volcano, Indonesia. Bull. Volc. 72, 961–970 (2010).
Slad, G. & Merchant, B. Evaluation of low cost infrasound sensor packages. Sandia Natl. Lab. https://doi.org/10.2172/1829264 (2021).
This work was made possible through support from INSIVUMEH and Fuego Volcano Observatory staff Amilcar Calderas, Edgar Barrios, Sarai Perez. Their logistical and safety support and historical knowledge of the volcano was critical. Funding for this work was made possible from the National Science Foundation EAR grants 1914491 and 1914526 awarded to Boise State University and Michigan Technological University as a collaborative project. Fuego’s digital topography was provided by the UN-SPIDER program, United Nations Office for Outer Space Affairs (UNOOSA).
The authors declare no competing interests.
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Johnson, J.B., Roca, A., Pineda, A. et al. Infrasound detection of approaching lahars. Sci Rep 13, 6476 (2023). https://doi.org/10.1038/s41598-023-32109-2
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.