Abstract
Infrasound is increasing applied as a tool to investigate magma dynamics at active volcanoes, especially at open-vent volcanoes, such as Mt. Etna (Italy), which are prodigious sources of infrasound. Harmonic infrasound signals have been used to constrain crater dimensions and track the movement of magma within the shallow plumbing system. This study interprets the remarkable systematic change in monotonic infrasound signals preceding a lava fountaining episode at Mt. Etna on 20 February 2021. We model the changing tones (0.7 to 3 Hz fundamental frequency) as a rise in the magma column from 172 ± 25 m below the crater rim to 78 ± 8 m over the course of 24 h. The infrasonic gliding disappears approximately 4 h before the onset of lava fountaining as the magma column approaches the flare of the crater and acoustic resonance is no longer supported. The featured 20 February event was just one of 52 lava fountain episodes that occurred at Mt. Etna over the course of 9 months in 2021 and was the only lava fountain episode where dramatic gliding was observed as a subsequent partial collapse of the crater prevented future resonance. The results presented here demonstrate that analysis of infrasonic gliding can be used to track the position of the magma free surface and hence may provide information on the processes taking place within the plumbing system before eruptive activity.
Similar content being viewed by others
Introduction
On 16 February 2021 a volcanic plume deposited ash and lapilli on Catania and other villages near Mt. Etna. The plume reached about 10 km above sea level and originated from a vent located in the area of the South-East Craters (SEC; Fig. 1) where Strombolian explosions, lava flows, and lava fountaining were also observed. The lava fountaining lasted for 3 h and reached a maximum height of 1.5 km. This eruptive episode (or paroxysm) was the first of a sequence of 52 lava fountain episodes that occurred in 2021. Such eruptive behavior is common at Etna’s SEC1 and is reminiscent of eruptive behavior that occurs at other volcanoes, like at Kilauea’s P’u’ ‘O’o vent in 20032.
The 52 lava fountain paroxysms in the 2021 eruptive sequence followed a remarkably consistent pattern with only minor differences in event duration. Each paroxysmal episode was characterized by three main phases articulated in Alparone et al.1 and Andronico et al.3 as: (i) resumption phase marked by Strombolian activity resumption lasting tens of minutes to a few days, (ii) paroxysmal phase lasting from tens of minutes to a few hours and consisting of continuous to almost continuous lava fountains and lava overflow, and (iii) conclusive phase characterized by the return to low levels of eruptive phenomena until their total exhaustion. Telemetered networks operated by INGV (Fig. 1; see section Methods) recorded seismo-infrasonic waves emitted in the ground-atmosphere during eruptive activity.
The fourth lava fountain episode of the 2021 sequence (referred to as episode #4), occurring on 20 February, was observationally similar to other paroxysms in regards to the main phases characterizing the episode and their temporal succession. The lava fountaining phase lasted for three hours (approximately from 22:00 to 01:00) and produced jets with maximum height of about 1.5 km, while the eruptive plume reached around 10 km a.s.l..
This episode was unique, however, in terms of its monotonic infrasonic spectra (consisting of a single peak in the frequency domain). Strombolian activity intensified and culminated in lava fountaining after being preceded by more than 24 h of monotonic infrasound, characterized by a well-defined fundamental frequency. The monotonic infrasound began as discrete events, which became more intense and frequent and eventually merged into a continuous infrasonic tremor, which retained its monotonic signature.
Over the course of the 24 h preceding episode #4, the fundamental tone of the monotonic infrasound rose from 0.7 Hz to 3 Hz in a pattern referred to as spectral gliding. Gliding has been commonly observed in seismic tremor at a number of volcanoes (i.e. Lascar,4; Montserrat,5; Veniaminof,6; Redoubt,7), but less frequently in infrasound signals8,9,10. Our featured example at Etna is the clearest example of infrasonic spectral gliding that we have seen reported.
Seismic and acoustic gliding likely reflect changing resonance characteristics in different parts of a volcano. Several mechanisms have been proposed for seismic gliding including resonance of portions of the plumbing system, resonance of gas-filled bubbles, combination of discrete pulses producing evenly spaced harmonics, non-linear fluid flow, and/or non-linear responses to fluid flow7,11. Harmonic infrasound signals have been observed at open-vent volcanoes and have been attributed to Helmholtz12,13 or acoustic resonance of the volcanic crater14,15, repeating discrete pulses16,17, or complex source time functions18. Infrasonic gliding has been modeled as due to the rise or fall of magma within a resonating conduit14,19,20. Harmonic infrasound signals, without gliding, have previously been observed at Mt. Etna and attributed to acoustic resonance occurring between the top of the magma column and the crater outlet13,20,21,22. This study integrates infrasound along with seismic observations and visual and thermal imagery constraints to better understand the source of infrasonic gliding and to develop a quantitative model of magma column rise (position, velocity, and volume) over time. The tracking of rising magma by infrasound analysis has implications for unravelling the processes taking place within the shallow magma plumbing system and can provide higher temporal resolution than other methods such as visual overflights.
Results
Geophysical data
In order to investigate the dynamics of episode #4, we focused on 36 h of infrasonic and seismic data from 19 February at 12:00 to 21 February at 00:00 UTC (Fig. 2). This time period starts several hours before the resumption of visible volcanic activity and encompasses both the Strombolian activity and growth of the lava fountain.
Infrasound
The infrasound data in Figs. 2a,c,e show systematic variation in the 20 h preceding episode #4 with the peak frequency of the monotonic infrasound signal increasing from 0.7 to 3 Hz. Waveform examples of infrasound signal types recorded during this time interval, together with the associated seismic signal, are plotted in Fig. 3. Mount Etna has a complicated summit terrace with several craters sometimes active simultaneously. Because two crater areas (BN and SEC) were active during this period, we perform network infrasound processing, as described in Cannata et al.23, to identify the infrasound source location. This analysis confirms that the vast majority of discrete events and tremor were located at SEC (Fig. 4).
Prior to the onset of Strombolian activity, we divide the eruptive activity into three phases, as annotated in Fig. 2.
The first phase is from 12:00 on 19 February (when we start our analysis) to 00:00 on 20 February. Between 12:00 and 14:00 there are several discrete explosive events that were located in the SEC area (Fig. 4). These events are superimposed ontop of a continuous signal, characterized by relatively broadband spectral energy between 0.3 and 1 Hz, and associated with non-volcanic microbaroms generated by ocean noise24. The microbarom is distinguishable from the volcanic signal as it is incoherent across the network whereas the low frequency volcanic tremor is coherent. From 21:00 on 19 February to 00:00 on 20 February, a low amplitude monotonic infrasound signal with a peak frequency of 0.7 Hz emerges from the background ocean noise.
The second phase is from 00:00 to 06:00 on 20 February. During this time, the amplitude of the monotonic infrasound signal decreases and the microbarom becomes more evident, particularly on the normalized infrasound spectrogram (Fig. 2e). We exclude this phase from our later analysis in order to avoid misinterpreting the low frequency microbarom as volcanic signal. Note that when observed, the peak frequency of the monotonic infrasound signal is constant at 0.7 Hz during this phase.
The third phases is from 06:00 to 19:00 on 20 February. During this time the infrasound events increased in amplitude and occurred more frequently (Fig. 4) prior to the onset of visible Strombolian activity at 19:00 (Fig. 5). The most significant change, and the focus of this study, is the dramatic increase in peak frequency of the monotonic infrasound signal from 0.7 to 3 Hz.
A comparison of visual and thermal imagery observations with infrasonic signal character helps to illuminate the changing phases of episode #4 (Fig. 5; animation in Supplementary Material). The infrasonic gliding and peaked spectral signal disappeared at about 19:00 on 20 February at the same time as weak Strombolian activity became visible at SEC (INGV, 2021). The explosive activity evolved into strong Strombolian activity an hour later at 20:00 (Fig. 5) and finally into lava fountaining at 22:0027. Both transitions were accompanied by a large increase in infrasonic and seismic amplitude (Figs. 2, 3e,f) and the occurrence of a continuous infrasonic tremor (Fig. 4a,d,e).
Joint comparison of seismic data reveals interesting first-order observations (Figs. 2b,d,f and 3). Notably, there is minimal seismic signal with no distinct spectral character prior to the start of Strombolian activity at 19:00. Seismic tremor amplitude increases with the onset of the visual eruption, yet no monotonic signal or spectral gliding is observed. After 20:00, the seismic signal rapidly increases in amplitude and has broad spectral content. The increased spectral amplitude corresponds with the onset of strong Strombolian activity and lava fountaining as observed by thermal imagery (Fig. 5). Joint seismo-acoustic observations, with gliding observed in the infrasound but not in the seismic data (Fig. 3a–d), point to the resonance phenomena occurring in the open crater/conduit of the SEC and coupling well to the atmosphere but not to the ground.
The prominent infrasound signal and lack of seismic signal suggests a source with good coupling to the atmosphere and poor coupling to the solid Earth. Several factors affect the relative partitioning of acoustic and seismic energy such as the location of the explosive/degassing source, the impedance contrasts between magma and the volcano edifice, the source dimension and the conduit conditions25. For this eruption, we suspect that the source was subaerial and located very shallow (at the top of the magma column) leading to efficient acoustic radiation but inefficient seismic emission.
This infrasonic gliding observation was common to the signals acquired by all the analyzed infrasonic stations and, as such, is likely indicative of a source process rather than changing propagation conditions.
Infrasound modeling
We model the gliding monotonic infrasound signal as an acoustic resonance of the crater and conduit, whose length changes with time as magma ascends in the conduit. Acoustic resonance of volcanic craters occurs when acoustic waves, excited by explosions or unsteady degassing at the top of the magma column, are reflected from the crater outlet due to a contrast in the acoustic impedance between the crater outlet and the atmosphere15,26. For a narrow cylindrical pipe (ka < < 1 where k is the wavenumber and a is the radius) that is closed at the base and open at the outlet, the resonant frequency, f, is given by:
where c is the speed of sound and L is the length of the resonating cylindrical cavity (i.e., depth from crater outlet to the top of the magma column). Equation (1) predicts an inverse relationship between pipe length and acoustic frequency and provides a rough estimate of expected resonant frequency for a crater with a specific depth. Equation (1) indicates how the infrasound peak frequency rises as magma rises in a conduit and effectively shortens the pipe length. Explosions, which became visible at SEC soon after 19:00 on 20 February27, correspond to when the highest infrasound peak frequencies were observed (Figs. 2, 3e,f). This supports the hypothesis that the magma column was high within the crater/conduit at this time.
Several previous studies have utilized Eq. (1) to relate harmonic infrasound observations to crater dimensions21,22,28, but they have also acknowledged that Eq. (1) is an idealization because volcanic craters are not perfectly cylindrical and/or ka is not far smaller than 1. Hence other studies have used expressions accounting for non-narrow pipes and/or have utilized the analytical solutions for exponential or Bessel horns, to model frequency as a function of crater size14,29. More recently, numerical models, both 1D and 3D, have been used to account for more complex geometries15,20,30,31. The SEC geometry at Etna is not easily characterized by an analytical expression or geometric approximation. Visual observations of the SEC and structure-from-motion mapping efforts reveal a shallow 65-m-radius crater sloping down towards a vertical conduit with a radius of about 10 m starting about 58 m below the surface. The conduit length is presumed to be variable, changing as magma rises and falls. The coupled crater and conduit, heretofore referred to as the SEC, appears axisymmetric (Fig. 6). The SEC has the appearance of a long-stem funnel and accounts for the system’s resonant frequencies and resonant character.
Forward modeling
Our analysis uses CRes (Crater Resonance32), which is a numerical model for simulating the crater acoustic response for quasi-1D crater geometries, to model the infrasound signal observed at Mt. Etna. CRes solves the linear acoustics wave equation within the crater and models acoustic radiation outside of the crater as radiation from a baffled piston. For more details, refer to Watson et al.15. We use the CRes model to calculate the acoustic response, and peak frequency values, of the SEC for varying magma levels. The CRes model has been shown to be a good predictor of crater acoustic response for relatively narrow conduits and craters; a comparison of CRes results with 3D modeling confirming this is provided in Methods.
A digital elevation model of the SEC was reconstructed from topography acquired by an unoccupied aerial system (UAS) survey flown on 3 March 2021 and constrained by satellite observations (Fig. 6), whereas the lava fountaining episode considered here occurred on 20–21 February. The SEC rim has a horseshoe shape, opening toward SE (Fig. 6a), due to a collapse that occurred during the eruptive episode of the 12–13 December 2020. From 21 February, an escarpment was visible in the SE crater rim, likely a consequence of structural weakness due to the numerous fractures that characterized the east flank of the cone. Continued failure and collapse caused the escarpment to deepen and was observed in satellite images from 23 February and 3 March (Fig. 6b,c). We hypothesize that the change in crater geometry meant that the crater could no longer efficiently support acoustic resonance and this is one of the reasons why only the fourth lava fountain exhibited gliding (see section Discussion).
Allard et al.33 has reported magmatic temperatures of ~ 1100 °C at Mount Etna, however entrainment of ambient air means that the temperature within SEC will likely only be several hundreds of degrees celsius. This is supported by the temperature measurements performed by Fee et al.12, who estimated temperatures of 200 °C within the gas-filled cavity of the Halema’uma’u Crater (Kilauea Volcano, Hawaii), and by Sawyer et al.34 , who retrieved volcanic gas temperatures in the range 27°–267 °C above the lava lake in Nyiragongo (Congo). In previous work on monotonic infrasound signals, Johnson et al.28 combined analytical expressions for the peak frequency and quality factor of a resonating pipe to estimate a constant air temperature within the crater at Cotopaxi (Ecuador). However, it is unclear how this approach can be applied to complex crater geometries or a spatially variable temperature profile.
We do not have any direct observational constraints on the air temperature within the crater/conduit or its variation with depth. The air temperature within the crater/conduit will increase as magma ascends in the crater, however, we note that Watson et al.15 demonstrated that a spatially varying temperature profile has a minimal impact on the peak frequency (Supplementary Fig. 3). Hence, rather than trying to account for the second-order effects of spatially variable and changing air temperature, we assume a constant air temperature of 200 °C. The speed of sound is calculated by
where c is the sound speed, \(\gamma\) is the ratio of heat capacities (\(\gamma\)=1.4 for an adiabatic process), R is the specific gas constant, and T is the temperature in Kelvin.
Based on INGV observations (personal communications), we assume an atmospheric temperature of −7.5 °C. We examine the sensitivity of the results to the assumed temperature profile in the Supplementary Material.
We use CRes to simulate the acoustic response function for sources located at the bottom of SEC where SEC depths range from 300 to 50 m at 1 m intervals, reflecting possible magma depths in the conduit. Figure 7b shows the normalized spectrogram of the SEC response as a function of magma level. As expected, it shows systematic variations in both the fundamental mode and the overtones. The acoustic response function is the impulse response of the crater geometry15. In contrast, the recorded infrasound signal (Fig. 2c,e) is the time-domain convolution of the acoustic response function with a source function. Compared to an impulse source that has equal energy at all frequencies, realistic source functions have limited energy at high frequencies15. CRes only accounts for damping through acoustic radiation whereas there are additional sources of damping in nature, such as intrinsic attenuation and coupling of acoustic waves to the solid Earth. Furthermore, higher frequency signals are more rapidly attenuated with distance. This explains why only the fundamental peak is visible in the data whereas there are multiple overtones seen in Fig. 7b. While the choice of source function strongly influences the overtones, the fundamental model is relatively unaffected15 (Supplementary Figure 2). Therefore, rather than assuming an arbitrary source function, we perform our analysis with the acoustic response function.
The results from CRes 1D modeling confirm a monotonic relationship between magma level and frequency (Fig. 7b), which allows for frequency to be used as a unique proxy for SEC depth. Because the frequency changes are significant and correspond to magma surface within a deep conduit the analysis does not require incorporation of an infrasound quality factor used in other studies19,28.
Inversion
The CRes simulations produce an unique relationship between peak frequency and depth (Fig. 7b). Based on this information, we can relate the observed peak frequency at each time (Fig. 8b) with a depth value (Fig. 8c) in order to invert the infrasound observations for the depth. During phase 2 (00:00 to 06:00 on 20 February) the volcanic signal decreased in amplitude and the microbarom dominated the infrasound recordings, hence we focus our analysis of phases 1 and 3 when there are clear volcanic signals recorded.
The spectral evolution of the recorded infrasound (Figs. 2, 8a,b), indicates a systematic increase in frequency that can be attributed to rising magma column and decreasing depth of SEC (defined as the distance from crater rim to inferred magma level). Starting at 22:00 on 19 February, the magma column appears to be deep (170 ± 25 m) within the conduit. From 00:00 to 06:00 on 20 February, infrasonic volcanic activity decreased to the point where the microbarom peak dominates and the 0.7 Hz tremor is only intermittently evident (Fig. 8a). From 06:00 to 19:00 the peak frequency increases, slowly at first and then more rapidly after 15:00. This is modeled as a depth decrease from 167 ± 25 m to 138 ± 19 m over nine hours (average velocity of 3.2 m per hour) and a decrease from 138 ± 19 m to 78 ± 8 m over the course of four hours (average velocity of 15 m per hour) (Figs. 8c, 9a).
In addition to the CRes inversion, we invert the peak frequency for the depth using Eq. (1) with c = 436 m/s, which corresponds to a temperature of 200OC (Fig. 8c). Equation (1) describes the geometry as a cylindrical pipe and does not account for the flaring crater geometry (Fig. 7a). Despite this simplified geometry, the inverted depths using Eq. (1) are qualitatively similar to the CRes results (~ 30 m shallower) and show the same pattern of accelerating magma ascent prior to the onset of lava fountaining. While the CRes inversion is computationally efficient, it can take significant time to determine the various inputs parameters, particularly the crater geometry. In contrast, Eq. (1) is a simple model that only requires sound speed as an input parameter but produces qualitatively similar results. Equation (1) can easily be calculated in real-time (either for a single sound speed or for a realistic range of values) and would be straightforward to incorporate this analysis into existing monitoring workflows. We note that there is reasonable agreement between Eq. (1) and the CRes inversion for the crater geometry considered here but this may not be the case at other volcanoes with different geometries.
The monotonic infrasound signal disappears after 19:00 as the eruption transitions to Strombolian activity (Fig. 3e,f) and lava fountaining with broadband infrasound signal (Fig. 8a). Therefore, after 19:00 we can no longer invert the peak frequency for the depth. We attribute the loss of resonance to the magma level reaching the flaring crater of SEC where open conduit resonance is no longer sustained.
We use a moving median with a sliding window of 2 h to smooth the inverted depths and then differentiate to calculate the magma ascent velocity as a function of time (Fig. 9a). The volumetric ascent rate is estimated by multiplying the ascent velocity with the cross-sectional area of the crater (Fig. 9b). The maximum volumetric ascent rate is ~ 6300 m3/hr and the mean value is ~ 1800 m3/hr, which is approximately 0.5 cubic meters per second. The calculated volumetric ascent rates are sensitive to the assumed geometry and cross-sectional area of SEC. While uncertainty of the conduit radius is difficult to quantify, we note that volumetric ascent rate scales with the square of the radius meaning that small errors in the conduit radius lead to large errors in the volumetric ascent rate. Nonetheless, the numbers presented here provide a useful illustration of how infrasound can constrain both magma rise rates and volume fluxes.
Discussion
Acoustic resonance
The monotonic infrasound signal, recorded before the onset of the 20 February lava fountain (Fig. 2), suggests strong acoustic resonance of the volcanic crater, which has been previously observed at Mt. Etna13,20,21,22. The lack of seismic signal accompanying the featured monotonic infrasound signal indicates that the source occurs in a conduit-like volume with good coupling to the atmosphere and relatively poor coupling to the solid Earth. We hypothesize that acoustic waves are generated by explosions and unsteady degassing at the magma free surface.
The resonant frequency of the radiated infrasound is similar at all stations (Fig. 8b) indicating that the observations are due to lumped source and SEC response effects, as opposed to propagation effects outside the SEC or site effects local to each station. Previous work at other volcanoes has demonstrated the possible influence of topographic scattering for local infrasound observations35,36,37, however the remarkable consistency in peak frequency observations here indicates that topographic effects are a second-order influence (at least for the low frequencies (< 3 Hz) considered here).
Infrasonic gliding is a particularly remarkable feature of the monotonic signal featured in this study. Although gliding has been reported for volcano seismic tremor, the observations of gliding in the volcano infrasound wavefield are limited. Spectral shifts in the infrasound wavefield have been mentioned in a few studies, such as at Arenal38, Pu`u `Ō`ō39 and Tungurahua40, however they entailed only a brief duration, occurred before or after single explosions and/or were characterized by both the increase and the decrease of peak frequencies38,40,41. Shifting in the spectral peaks of the harmonic tremor has usually been attributed to variation in speed of sound in the fluid (assuming acoustic resonance)38 or it has been related to repeated low-frequency events or ‘chugging’ phenomena, where harmonic infrasound is accompanied by audible pulsing41.
Etna’s long-duration (~ 20 h) evolution in monotonic tremor and systematic increase in frequency is perhaps most analogous to infrasonic frequency changes observed at Villarrica (Chile) in the 5 days leading up to its 3 March 2015 lava fountaining episode. At Villarrica the fundamental frequency of discrete explosion signals rose from 0.7 to 0.95 Hz (30% increase) and was accompanied by a drop in coda resonance as the lava free surface rose, first within a pipe-like conduit and then up into the broader crater19. As with the episode at Etna, the shallow level of the magma free surface preceded observable Strombolian activity and then, a few hours later, a vigorous lava fountain 1.5 km high.
The frequency change at Etna between 19 and 20 February was far more rapid and dramatic (from 0.7 to 3 Hz; 400% change) than at Villarrica, occurring over the course of just 18 h. The higher resonant frequency supported by Etna’s SEC, compared to Villarrica, is explained by resonance of a narrower pipe (10 m compared to 30 m radius) and smaller size of crater (less than 60 m deep at Etna). Etna’s infrasound reached a maximum value of 3 Hz at about 18:00 on February 20th and stabilized at this level for around an hour, before disappearing. Our depth inversion suggests that the magma is high and has possibly reached the flaring portion of the crater at this time (Fig. 8c). As the magma rises and the vertical conduit disappears so does the resonance. Strombolian activity after 19:00 and ensuing lava fountaining are characterized by broadband infrasound signals (Fig. 8). Our interpretations are supported by the results obtained in Spina et al.42, who performed analogue degassing experiments and simulated harmonic acoustic tremor. They recorded audio frequencies in a resonating conduit as they modified the level of the silicone oil (analogue magma) through which gas bubbles were permitted to rise and burst.
A principal question is why only episode #4 was preceded by a very evident gliding phenomenon (Fig. 10). To support acoustic resonance a particular geometry is needed as well as a source phenomenon that excites acoustic waves15. In the months before the first lava fountain, SEC was affected by almost continuous Strombolian activity43 (Fig. 10a,b). We speculate that the three previous lava fountain episodes (16, 17–18 and 19 February) had no obvious monotonic gliding signal because the magma column level was shallow during these episodes, which prevented effective resonance (Fig. 10a,b). The first three lava fountains emitted a total volume of 10 Mm327, which is much larger than the average volume of 1.1 Mm3 for typical lava fountaining episodes at Mt. Etna44. We speculate that these large discharges drained magma from the conduit so that prior to episode #4 the magma level was deep in the conduit, which allowed for efficient resonance and the observation of a very evident infrasonic gliding as the magma column rose prior to lava fountaining.
Concerning the absence of gliding in lava fountains following episode #4, after the 22 February episode, the summit area of the SEC changed significantly and a horseshoe-shaped scar was formed by the coalescence of multiple active vents during the lava fountains and partial collapse of the crater wall (Fig. 10a,f,g). The destructive nature of the waning portion of episode #4 is evident in the thermal video (Supplementary Video 1). We propose that changing conduit and crater properties inhibited the development of resonance during successive lava fountain episodes. Furthermore, we speculate that during the other episodes where gliding was absent, the magma level might not have been deep enough with SEC and/or the resonance excitation mechanism (bubble bursting and degassing) might not have been energetic enough to produce resonance. We note that the focus of this research is investigating the gliding phenomenon and constraining magma movements, rather than exploring the precise source mechanism that causes the acoustic resonance, which we hope will be the goal of future studies.
Magma ascent
The ascent position over time can be used to calculate the magma ascent rate and the associated volumetric flux into the conduit (Fig. 9). This result represents one of the first examples of using infrasound to constrain magma rise rates leading to an eruption. In previous work, Richardson et al.14 used infrasound and seismic data to examine changes in the lava lake level at Villarrica over a period of weeks. Sciotto et al.13 and Spina et al.21 related changes in infrasound peak frequency at Mt. Etna to changes in magma column height and pressure in the magma chamber in time periods preceding and/or following eruptions. Watson et al.20 previously examined harmonic infrasound observations at Mt. Etna during the “Christmas Eve” 2018 eruption and inferred a decrease in the magma column accompanying a flank eruption. Watson et al.20 focused on two time windows (before and after the flank eruption) and hence does not have the same temporal resolution as we obtained here. Johnson et al.19 tracked the ascent of magma prior to a paroxysmal eruption at Villarrica using infrasound data from a single station. While Johnson et al.19 calculated the depth to the magma column, they did not explicitly calculate the ascent rate or the volumetric flux. Furthermore, the change in peak frequency at Villarrica was an order of magnitude less than observed in this study.
Infrasound-derived depths of the magma surface hint at a mean ascent rate of 5 m/hr and a maximum rate of 22 m/hr. This is an order of magnitude greater than the rate observed by Johnson et al.19 at Villarrica where the magma column rose 70 m in 3 days (February 26th to March 1st), which gives an average ascent rate of ~ 1 m/hr, or 3000 m3/hr (~ 1 m3/s assuming a 30 m conduit radius). The narrower conduit of Etna’s SEC (~ 10 m; area of ~ 300 m2) leads to mean ascent rates of ~ 1450 m3/hour to a peak value of 6200 m3/hour (~ 2 m3/s). Notably, these volumetric rates may be affected by the variable density of the magma, which could be high (volatile-poor) or relatively low if the magma is gas-rich. The volumetric rates are also highly sensitive to the assumed conduit radius. The apparent acceleration of the rising magma surface could potentially be explained by a constant mass flux and increasing frothiness directly prior to the Strombolian activity.
Our ascent rates are mainly lower than the range of ascent rates (10–2–102 m/s) of basaltic melts inferred from methods such as isotopic-decay dating, crystal-size distribution analysis, melt-inclusion timekeepers, chemical-diffusion-based geo-speedometers, thermal modeling of magmatic systems, mechanical modeling of magma ascent and seismicity studies (Petrelli et al.45 and references therein). Our observations relate to the bulk movement of magma whereas other methods, such as melt-inclusion timekeepers and geo-speedometers, relate to the movement of individual crystals which may ascend faster than the bulk magma, potentially explaining why our observations are lower than other estimates of ascent rates. Furthermore, we note that we are analyzing the ascent of magma in the upper portion of an open conduit whereas many of these methods constrain ascent rates of dykes or other magma movement in the crust. Care should be taken when comparing ascent rates calculated for different phenomena.
Mt. Etna is one of the most well-monitored volcanoes in the world. In addition to the seismic, infrasound, and thermal camera data presented here, Mt. Etna is monitored with geodetic instrumentation consisting of tiltmeters and GNSS stations. The GNSS data can provide useful information about deformation and magma recharge during a sequence of lava fountains46,47. The uncertainties in the GNSS measurements, however, are generally too high to reliably measure deformation during a single paroxsym. Tilt data have higher temporal resolution and show that clear changes take place during each paroxsym from the summit vents47,48. While the deflation pattern due to eruption of magma from the summit is often clearly observed, the inflation pattern preceding eruptions is frequently weaker. For the paroxsym that we focus on here, the inflation pattern was only observed at a single tiltmeter, which means that the location and properties of the inflation source cannot be reliably constrained.
Perspectives and outlook
Open vent volcanoes like Mt. Etna are some of the most frequently erupting and hazardous volcanoes on the planet. Here we highlight a paroxysmal lava fountaining episode that was preceded by infrasonic gliding, where the peak frequency of monotonic infrasound signals increased in the days and hours prior to the eruption. We demonstrate how infrasound analysis, acoustic resonance modeling and high-resolution topographic surveys can be combined to track magma movements within the shallow plumbing system during infrasonic gliding. In particular, we place quantitative constraints on the magma depth, its ascent velocity and volumetric flux. The approach shown in this paper allows the magma dynamics in open vent volcanoes to be reconstructed in high temporal resolution.
During a volcanic crisis, time constraints mean that it is unlikely that observatory staff will be able to replicate the sophisticated topographic analysis and infrasound modeling shown here. Therefore, we demonstrate that the simple analytical model of an open-closed pipe can be used to produce qualitatively similar results (for the geometry considered here). We suggest that this technique could be applied at open vent volcanoes around the world to analyze infrasonic gliding and obtain qualitative constraints on magma movement in real-time.
The observations of infrasonic gliding prior to lava fountaining that are presented here and in previous work at Villarrica19 suggest that infrasonic gliding could be a precursory signal to lava fountaining under certain conditions. However, infrasonic gliding was only observed prior to one of the 52 lava fountaining episodes that occurred during the eruptive sequence of 2021 at Mt. Etna. In order for infrasonic gliding to be used as a forecasting tool, future work is needed to (1) better understand the conditions under which infrasonic gliding occurs, (2) determine the probability of lava fountaining occurring after infrasonic gliding (compared with the probability of infrasonic gliding occurring with no subsequent lava fountaining), and (3) develop a forecasting model that uses the infrasound-derived depth information as an input and outputs the likelihood of lava fountaining occurring. While we focus on lava fountaining in this study, infrasonic gliding could plausibly precede other styles of eruptive activity (i.e., effusive lava flows). Further observations of precursory infrasonic gliding are needed to determine if characteristics of the infrasonic gliding can be used to estimate the style of subsequent eruptive activity.
Methods
Volcanological context
On 24 December 2018 the violent “Christmas Eve eruption” began at Mt. Etna. The eruption lasted for three days during which a 2-km-long fissure opened on the south-east flank of the volcano22,49,50. From the end of this eruption until the end of 2020, Etna experienced a period of intermittent and energetically variable Strombolian activity, ash emission and lava flows. This activity took place from all of the summit craters (Fig. 1). Energetic and continuous activity was observed at Voragine (VOR), where, from September 2019 to May 2020, medium-to-high intensity Strombolian explosions and small lava flows took place. The SEC area was intermittently active in May–July 2019, while from December 2019 Strombolian explosions and weak ash emission were continuously observed at summit vents and on fractures opened on its flanks51. In April 2020 volcanic phenomena intensified, episodes of sustained Strombolian activity (late May) and a small lava fountain (19 April) occurred. From December 2020 and until the beginning of the lava fountain sequence on 16 February 2021, activity was focused at SEC with a few lava fountains, sustained Strombolian activity, small pyroclastic flows and lava effusion, the most significant of which occurred on 13, 21 and 22 December 2020 and 18 January 2021.
Crater geometry reconstruction
A UAS (unoccupied aerial system) topographic survey was performed on 3 March 2021. The UAS took off from the top of the 2002–2003 eruption scoria cone (1950 m a.s.l.; Fig. 1b). Sixty images were taken from an average altitude of 400 m, and 8 videos were recorded around the SEC, among these the most meaningful is shown as supplementary material (Supplementary Video 2). The survey covered an area of ~ 1 km2 and resulted in a digital elevation model (DEM) pixel resolution of 0.55 m and an orthophoto resolution of 12.9 cm. Structure-from-motion reconstructions using Agisoft Metashape produced a dense cloud of 2,821,217 points and a DEM with 0.55 m resolution and georegistration to the WGS 84 / UTM zone 33 N coordinate system.
Georeferencing by the UAS GPS in areas with steep slopes can have large uncertainties (> 50 m). Photogrammetry best practices suggest spreading ground control points evenly throughout the survey area, which is impossible to do on an active volcano. In order to get accurate georeferencing, we aligned the 2021 DEM with the 2014 DEM52 using the unchanged southern flank of the BN summit cone. This correction results in inaccurate absolute elevation values but allows for the calculation of relative distances, such as crater rim size and shape, which are the important values for our infrasound modeling.
The DEM produced from the UAS survey were compared with satellite images from Sentinel 2LC with a resolution ranging from 6.5 m to 8.9 m acquired on 18 and 23 February 2021 and 3 March 2021 (the same day as the UAS survey; Fig. 6). The satellite data were used to constrain the dimensions of the outer crater rim and confirm the results of the UAS survey. However, due to their lower resolution, the satellite data were not used to constrain the geometry of the inner crater. Instead, the 3 March 2021 UAS survey was compared with several other surveys performed over the SEC area after similar eruptive activity.
The UAS survey was collected on 3 March 2021 whereas lava fountain episode #4 occurred on 22 February 2021. The summit area of the SEC changed significantly after episode #4 and a horseshoe-shaped scar was formed (Figs. 6 and 10). We compare the UAS survey with satellite images from 18 and 23 February (Fig. 6a,b) to estimate the crater geometry during the period of interest. As a result, we use the north–south transect (b-b’) shown in Fig. 6d to construct the quasi-1D crater geometry used in our modeling.
Geophysical data
Seismo-acoustic data was recorded by the permanent monitoring network run by Istituto Nazionale di Geofisica e Vulcanologia – Osservatorio Etneo (INGV-OE; Fig. 1). Infrasound data was recorded at 10 stations, equipped with a GRAS 40AN sensor (microphone) with a sensitivity of 50 mV/Pa. Infrasound data have a flat response between 0.3 Hz (instrument roll-off) and 20 kHz (+ /−2 dB) and recorded at 50 Hz with a 25 Hz Nyquist frequency. Seismic data was recorded by co-located broadband (40 s), three-component Trillium Nanometrics seismometers, acquiring at a sampling rate of 100 Hz with a flat response between 0.025 and 50 Hz. We analyzed infrasound data recorded by stations ECPN, EMFO, EMFS, EMNR and ESLN as they had the best signal-to-noise ratios. These stations range in distance from 1.3 to 8.1 km from the active vent.
Seismic and infrasound spectra are calculated within 81.92 s long windows (212 or 213 samples for infrasonic and seismic signals, respectively) and averaged over 10 min time windows (Fig. 2). Infrasound events and infrasonic tremor windows are first detected from the continuous signal by means of STA/LTA and cross-correlation based trigger algorithm, respectively23,53. Once extracted, the source locations for the infrasound signals were computed by grid-search methods based on the computation of brightness function for the infrasonic events and semblance function for the infrasonic tremor23,53 (Fig. 4), while event amplitude is expressed by pressure values reduced to 1 km from the source. The source location analysis was performed by using signals recorded by the whole infrasonic permanent network composed of 9 stations (Fig. 1).
Uncertainty in the locations was estimated by the jackknife technique54, which is also called “leave one out”. The location algorithm is repeated n times where n is the number of stations (there are 9 infrasound stations in the permanent network; Fig. 1) with a different station left out of the analysis each time. The error values are calculated by using the n location results, as well as the location results constrained by the whole network. More details can be found in Sect. 3.1 of Cannata et al.23. In Fig. 3 we only show the relatively well constrained events with location uncertainties of less than 250 m.
Thermal imagery
We have incorporated thermal imagery analysis from the thermal camera located at station EMOT (yellow square in Fig. 1). To track the evolution of the explosive activity over time, we followed the method proposed by Gaudin et al.55 and processed the thermal images. For frame regions cropped above SEC we calculated the maximum temperature as a function of height. The time/height diagram (Fig. 5) then shows the normalized temperatures and provides a qualitative record of when Strombolian activity and lava fountaining commence.
Uncertainty analysis
Depth inversion from infrasound frequency content is subject to several possible sources of uncertainty. We consider the effects of four primary assumptions including model choice, uncertainty in topographic terrain, source spectrum, and conduit temperature. The uncertainty analysis is described in the Supplementary Materials.
Data availability
In accordance with INGV's data policy, infrasound data are publicly available at https://doi.org/10.13127/etna_infra/raw_20210219_20 and seismic data (belonging to the Italian Seismic Network, code IV) can be downloaded through EIDA database (European Integrated Data Archive http://eida.rm.ingv.it/). The latest version of the modeling code CRes is hosted at https://github.com/leighton-watson/CRes and the version used in this paper is archived at https://doi.org/10.5281/zenodo.3235682.
References
Alparone, S., Andronico, D., Lodato, L., & Sgroi, T. Relationship between tremor and volcanic activity during the Southeast Crater eruption on Mount Etna in early 2000. J. Geophys. Res.: Solid Earth 108(B5) (2003).
Heliker, C. C., Kauahikaua, J., Sherrod, D. R., Lisowski, M. & Cervelli, P. F. The rise and fall of Pu ‘u ‘O ‘o cone, 1983–2002. US Geol. Surv. Prof. Pap 1676, 29–51 (2003).
Andronico, D., Cannata, A., Di Grazia, G. & Ferrari, F. The 1986–2021 paroxysmal episodes at the summit craters of Mt. Etna: Insights into volcano dynamics and hazard. Earth-Sci. Rev. 220, 103686 (2021).
Hellweg, M. Physical models for the source of Lascar’s harmonic tremor. J. Volcanol. Geoth. Res. 101, 183–198 (2000).
Neuberg, J., Luckett, R., Baptie, B. & Olsen, K. Models of tremor and low-frequency earthquake swarms on Montserrat. J. Volcanol. Geoth. Res. 101(1–2), 83–104 (2000).
De Angelis, S. & McNutt, S. R. Observations of volcanic tremor during the January–February 2005 eruption of Mt. Veniaminof Alaska. Bull. Volcanol. 69.8, 927–940 (2007).
Hotovec, A. J., Prejean, S. G., Vidale, J. E. & Gomberg, J. Strongly gliding harmonic tremor during the 2009 eruption of Redoubt Volcano. J. Volcanol. Geoth. Res. 259, 89–99 (2013).
Johnson, J. B. & Lees, J. M. Plugs and chugs — seismic and acoustic observations of degassing explosions at Karymsky, Russia and Sangay, Ecuador. J. Volcanol. Geoth. Res. 101(1–2), 67–82 (2000).
Lees, J. M., Johnson, J. B., Ruiz, M., Troncoso, L. & Welsh, M. Reventador Volcano 2005: Eruptive activity inferred from seismo-acoustic observation. J. Volcanol. Geoth. Res. 176(1), 179–190 (2008).
Ichihara, M., Lyons, J. J. & Yokoo, A. Switching from seismic to seismo-acoustic harmonic tremor at a transition of eruptive activity during the Shinmoe-dake 2011 eruption. Earth, Planets and Space 65(6), 633–643 (2013).
Jellinek, A. M. & Bercovici, D. Seismic tremors and magma wagging during explosive volcanism. Nature 470, 522–525 (2011).
Fee, D. et al. Infrasonic harmonic tremor and degassing bursts from Halema’uma’u Crater, Kilauea Volcano, Hawaii. J. Geophys. Res. 115, B11316. https://doi.org/10.1029/2010JB007642 (2010).
Sciotto, M., Cannata, A., Gresta, S., Privitera, E. & Spina, L. Seismic and infrasound signals at Mt. Etna: Modeling the North-East crater conduit and its relation with the 2008–2009 eruption feeding system. J. Volcanol. Geoth. Res. 254, 53–68. https://doi.org/10.1016/j.jvolgeores.2012.12.024 (2013).
Richardson, J. P., Waite, G. P. & Palma, J. L. Varying seismic-acoustic properties of the fluctuating lava lake at Villarrica volcano, Chile. J. Geophys. Res.: Solid Earth 119, 5560–5573. https://doi.org/10.1002/2014JB011002 (2014).
Watson, L. M., Dunham, E. M. & Johnson, J. B. Simulation and inversion of harmonic infrasound from open-vent volcanoes using an efficient quasi-1D crater model. J. Volcanol. Geoth. Res. 380, 64–79. https://doi.org/10.1016/j.jvolgeores.2019.05.007 (2019).
Hagerty, M. T., Schwartz, S. Y., Garces, M. A. & Protti, M. Analysis of seismic and acoustic observations at Arenal Volcano, Costa Rica, 1995–1997. J. Volcanol. Geoth. Res. 101, 27–65. https://doi.org/10.1016/S0377-0273(00)00162-1 (2000).
Lees, J. M., Gordeev, E. & Ripepe, M. Explosions and periodic tremor at Karymsky volcano, Kamchatka, Russia. Geophys. J. Int. 158(3), 1151–1167 (2004).
Jolly, A., Kennedy, B., Edwards, M., Jousset, P. & Scheu, B. Infrasound tremor from bubble burst eruptions in the viscous shallow crater lake of White Island, New Zealand, and its implications of interpreting volcanic source processes. J. Volcanol. Geoth. Res. 327, 585–603. https://doi.org/10.1016/j.jvolgeores.2016.08.010 (2016).
Johnson, J. B., Watson, L. M., Palma, J. L., Dunham, E. M. & Anderson, J. F. Forecasting the eruption of an open-vent volcano using resonant infrasound tones. Geophys. Res. Lett. https://doi.org/10.1002/2017GL076506 (2018).
Watson, L. M., Johnson, J. B., Sciotto, M. & Cannata, A. Changes in crater geometry revealed by inversion of harmonic infrasound observations: 24 December 2018 eruption of Mount Etna, Italy. Geophys. Res. Lett. https://doi.org/10.1029/2020GL088077 (2020).
Spina, L. et al. Insight into Mt. Etna’s shallow plumbing system from the analysis of infrasound signals, August 2007 - December 2009. Pure Appl. Geophys. 172, 473–490. https://doi.org/10.1007/s00024-014-0884-x (2015).
Cannavo’, F., Sciotto, M., Cannata, A. & Di Grazia, G. An integrated geophysical approach to track magma intrusion: The 2018 Christmas Eve eruption at Mount Etna. Geophys. Res. Lett. 46(14), 8009–8017 (2019).
Cannata, A. et al. Monitoring seismo-volcanic and infrasonic signals at volcanoes: Mt. Etna case study. Pure Appl. Geophys. https://doi.org/10.1007/s00024-012-0634-x (2013).
Bowman, J. R., Baker, G. E. & Bahavar, M. Ambient infrasound noise. Geophys. Res. Lett. 32, L09803. https://doi.org/10.1029/2005GL022486 (2005).
Johnson, J. B. & Aster, R. C. Relative partitioning of acoustic and seismic energy during Strombolian eruptions. J. Volcanol. Geoth. Res. 148, 334–354. https://doi.org/10.1016/j.jvolgeores.2005.05.002 (2005).
Rossing, T. D. & Fletcher, N. H. Principles of vibration and sound (Second) Vol. 1 (Springer, New York, 2004). https://doi.org/10.1017/CBO9781107415324.004.
INGV, 2021a. Bollettino settimanale sul monitoraggio vulcanico, geochimico e sismico del vulcano Etna. 15/02/2021 - 21/02/2021. Rep. N◦ 08/2021. Available at. https://www.ct.ingv.it/index.php/monitoraggio-e-sorveglianza/prodotti-del-monitoraggio/bollettini-settimanali-multidisciplinari/473-bollettino-settimanale-sul-monitoraggio-vulcanico-geochimico-e-sismico-del-vulcano-etna20210223/file.
Johnson, J. B. et al. Infrasound tornillos produced by Volcán Cotopaxi’s deep crater. Geophys. Res. Lett. https://doi.org/10.1029/2018GL077766 (2018).
Lyons, J. J. et al. Long period seismicity and very long period infrasound driven by shallow magmatic degassing at Mount Pagan, Mariana Islands. J. Geophys. Res.: Solid Earth 121, 188–209. https://doi.org/10.1002/2015JB012490 (2016).
Yokoo, A., Ishii, K., Ohkura, T. & Kim, K. Monochromatic infrasound waves observed during the 2014–2015 eruption of Aso volcano, Japan. Earth, Planets and Space 71, 12. https://doi.org/10.1186/s40623-019-0993-y (2019).
Ishii, K. & Yokoo, A. Combined approach to estimate the depth of the magma surface in a shallow conduit at Aso volcano, Japan. Earth Planets Space 73, 187. https://doi.org/10.1186/s40623-021-01523-z (2021).
Watson, L. M. CRes. https://doi.org/10.5281/zenodo.3235682 (2019).
Allard, P., Burton, M. & Muré, F. Spectroscopic evidence for a lava fountain driven by previously accumulated magmatic gas. Nature 433, 407–410. https://doi.org/10.1038/nature03246 (2005).
Sawyer, G. M., Carn, S. A., Tsanev, V. I., Oppenheimer, C., & Burton, M. Investigation into magma degassing at Nyiragongo volcano, Democratic Republic of the Congo. Geochem., Geophys., Geosyst. 9(2) (2008).
Kim, K. & Lees, J. M. Finite-difference time-domain modeling of transient infrasonic wavefields excited by volcanic explosions. Geophys. Res. Lett. https://doi.org/10.1029/2010GL046615 (2011).
Kim, K., Fee, D., Yokoo, A. & Lees, J. M. Acoustic source inversion to estimate volume flux from volcanic explosions. Geophys. Res. Lett. 42(13), 5243–5249. https://doi.org/10.1002/2015GL064466 (2015).
Fee, D. et al. Eruption mass estimation using infrasound waveform inversion and ash and gas measurements: Evaluation at Sakurajima Volcano, Japan. Earth Planet. Sci. Lett. 480, 42–52. https://doi.org/10.1016/J.EPSL.2017.09.043 (2017).
Garcés, M. A., Hagerty, M. T. & Schwartz, S. Y. Magma acoustics and time-varying melt properties at Arenal Volcano, Costa Rica. Geophys. Res. Lett. 25(13), 2293–2296 (1998).
Matoza, R. S., Fee, D., & Garcés, M. A. Infrasonic tremor wavefield of the PuuŌō crater complex and lava tube system, Hawaii, in April 2007. J. Geophys. Res.: Solid Earth 115(B12) (2010).
Fee, D., Garces, M. & Steffke, A. Infrasound from Tungurahua volcano 2006–2008: Strombolian to Plinian eruptive activity. J. Volcanol. Geoth. Res. 193(1–2), 67–81 (2010).
Lees, J. M. & Ruiz, M. Non-linear explosion tremor at Sangay, Volcano, Ecuador. J. Volcanol. Geoth. Res. 176(1), 170–178 (2008).
Spina, L., Cannata, A., Morgavi, D., Privitera, E. & Perugini, D. Seismo-acoustic gliding: An experimental study. Earth Planet. Sci. Lett. https://doi.org/10.1016/j.epsl.2021.117344 (2022).
INGV, 2021b. Bollettino settimanale sul monitoraggio vulcanico, geochimico e sismico del vulcano Etna. 08/02/2021 - 14/02/2021. Rep. N◦ 07/2021. Available at. https://www.ct.ingv.it/index.php/monitoraggio-e-sorveglianza/prodotti-del-monitoraggio/bollettini-settimanali-multidisciplinari/471-bollettino-settimanale-sul-monitoraggio-vulcanico-geochimico-e-sismico-del-vulcano-etna20210216/file.
Behncke, B. et al. The 2011–2012 summit activity of Mount Etna: Birth, growth and products of the new SE crater. J. Volcanol. Geotherm. Res. 270, 10–21 (2014).
Petrelli, M., & Zellmer, G.F. Rates and Timescales of Magma Transfer, Storage, Emplacement,and Eruption. In Dynamic Magma Evolution, Geophysical Monograph 254, First Edition, Edited by F. Vetere, American Geophysical Union (2021).
Patanè, D. et al. Insights into magma and fluid transfer at Mount Etna by a multiparametric approach: A model of the events leading to the 2011 eruptive cycle. J. Geophys. Res.: Solid Earth 118(7), 3519–3539. https://doi.org/10.1002/jgrb.50248 (2013).
Bruno, V. et al. The most intense deflation of the last two decades at Mt. Etna: the 2019–2021 evolution of ground deformation and modeled pressure sources. Geophys. Res. Lett. https://doi.org/10.1029/2021GL095195 (2022).
Gambino, S., Falzone, G., Ferro, A. & Laudani, G. Volcanic processes detected by tiltmeters: A review of experience on Sicilian volcanoes. J. Volcanol. Geoth. Res. 271, 43–54. https://doi.org/10.1016/j.jvolgeores.2013.11.007 (2014).
Bonforte, A., Guglielmino, F. & Puglisi, G. Large dyke intrusion and small eruption: The December 24, 2018 Mt. Etna eruption imaged by Sentinel-1 data. Terra Nova 31(4), 405–412 (2019).
Calvari, S. et al. The VEI 2 Christmas 2018 Etna eruption: A small but intense eruptive event or the starting phase of a larger one?. Remote Sensing 12(6), 905 (2020).
Giuffrida, M. et al. Tracking the summit activity of Mt. Etna volcano between July 2019 and January 2020 by integrating petrological and geophysical data. J. Volcanol. Geotherm. Res. 418, 107350. https://doi.org/10.1016/j.jvolgeores.2021.107350 (2021).
De Beni, E. et al. The Continuing Story of Etna’s New Southeast Crater (2012–2014): evolution and volume Calculations based on field surveys and Aerophotogrammetry. J. Volcanol. Geoth. Res. 303, 175–186. https://doi.org/10.1016/j.jvolgeores.2015.07.021 (2015).
Cannata, A., Sciotto, M., Spampinato, L. & Spina, L. Insights into explosive activity at eruptive fissure closely-spaced eruptive vents using infrasound signals: example of Mt. Etna 2008 eruption. J. Volcanol. Geotherm. Res. https://doi.org/10.1016/j.jvolgeores.2011.09.003 (2011).
Efron, B., The Jackknife, the Bootstrap and Other Resampling Plans (Soc. for Ind. and Appl. Math., Philadelphia, Pa., 1982).
Gaudin, D. et al. Integrating puffing and explosions in a general scheme for Strombolian-style activity. J. Geophys. Res.: Solid Earth https://doi.org/10.1002/2016JB013707 (2017).
Acknowledgements
We are indebted to the technicians of the INGV, Osservatorio Etneo, for enabling acquisition of the infrasound and seismic data. We also thank the work of the INGV, Osservatorio Etneo, technical staff for video-camera data, and for their maintenance of the monitoring equipment. L.W. was supported by a Rutherford Foundation Postdoctoral Fellowship from New Zealand Government funding and administered by the Royal Society Te Apārangi. A.C. thanks CHANCE project, II Edition, Università degli Studi di Catania (principal investigator A. Cannata) and grant PIACERI, 2020-22 programme (PAROSSISMA project, code 22722132140; principal investigator Marco Viccaro). This work was supported by National Science Foundation Grants EAR-1830976 (J.J.) and EAR-1949219 (L.W.). The authors are grateful to I. Koulakov for his manuscript handling and two anonymous reviewers, whose comments and suggestions helped improve the manuscript.
Author information
Authors and Affiliations
Contributions
M.S. and L.W. came up with the idea and designed the study. M.S. and A.C. performed the infrasonic and seismic analysis. L.W. and J.J. performed the infrasound modeling. E.D. and M.C. performed the UAS topographic survey and generated the digital elevation model of the vent region. All the authors wrote the manuscript.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Sciotto, M., Watson, L.M., Cannata, A. et al. Infrasonic gliding reflects a rising magma column at Mount Etna (Italy). Sci Rep 12, 16954 (2022). https://doi.org/10.1038/s41598-022-20258-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-022-20258-9
This article is cited by
-
Gas buffering of magma chamber contraction during persistent explosive activity at Mt. Etna volcano
Communications Earth & Environment (2023)
-
Towards scientific forecasting of magmatic eruptions
Nature Reviews Earth & Environment (2023)
-
Assessment of eruption source parameters using infrasound and plume modelling: a case study from the 2021 eruption of Mt. Etna, Italy
Scientific Reports (2023)
-
The influence of volcano topographic changes on infrasound amplitude: lava fountains at Mt. Etna in 2021
Bulletin of Volcanology (2023)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.