Abstract
Electrical and optical monitoring of neural activity is major approaches for studying brain functions. Each has its own set of advantages and disadvantages, such as the ability to determine cell types and temporal resolution. Although opto-electrical bimodal recording is beneficial by enabling us to exploit the strength of both approaches, it has not been widely used. In this study, we devised three methods of bimodal recording from a deep brain structure in awake head-fixed mice by chronically implanting a gradient-index (GRIN) lens and electrodes. First, we attached four stainless steel electrodes to the side of a GRIN lens and implanted them in a mouse expressing GCaMP6f in astrocytes. We simultaneously recorded local field potential (LFP) and GCaMP6f signal in astrocytes in the hippocampal CA1 area. Second, implanting a silicon probe electrode mounted on a custom-made microdrive within the focal volume of a GRIN lens, we performed bimodal recording in the CA1 area. We monitored LFP and fluorescent changes of GCaMP6s-expressing neurons in the CA1. Third, we designed a 3D-printed scaffold to serve as a microdrive for a silicon probe and a holder for a GRIN lens. This scaffold simplifies the implantation process and makes it easier to place the lens and probe accurately. Using this method, we recorded single unit activity and LFP electrically and GCaMP6f signals of single neurons optically. Thus, we show that these opto-electrical bimodal recording methods using a GRIN lens and electrodes are viable approaches in awake head-fixed mice.
Similar content being viewed by others
Introduction
Neural activity of the brain has been conventionally investigated by electrical recording and optical imaging1. Electrical recording has the advantage of high temporal resolution, which allows us to detect action potentials of individual neurons and high frequency neural oscillations reflecting the functional state of a local network2,3,4,5,6,7. Optical imaging using calcium indicators has the advantage of simultaneous recording of a large number of cells8,9, although the temporal resolution is low due to the chemical properties of currently available calcium indicators. In addition, using cell-type-specific expression of genetically encoded indicators, the activity of different cell types can be determined while it is not straightforward to do it when performing electrical recording in behaving animals.
Using either electrical or optical recording with its own set of advantages, many studies have contributed to our understanding of the brain functions. However, there are some circumstances where it would be beneficial to merge their advantages and perform opto-electrical bimodal recording. For example, one can monitor different functional states of the brain using electrical recording of local field potential (LFP) and simultaneously characterize the activity of a large number of a specific cell type using calcium imaging10,11. Another example would be to characterize the relationship between neuronal activity, which can be monitored electrically, and the activity of astrocytes, which requires calcium imaging. Thus, opto-electrical bimodal recording is important to advance our understanding of the brain functions.
In this study, we devised methods for opto-electrical recording by combining calcium imaging through a gradient-index (GRIN) lens and electrical recording using different types of electrodes. By chronically implanting the GRIN lens and electrodes in proximity, our method allows for simultaneous opto-electrical monitoring from the same brain area in awake head-fixed mice (Fig. 1). In such bimodal recording, one main challenge is the precise placement of the lens and electrode. To simplify that, we designed a custom-made 3D printed scaffold which ensures the accurate placement of a GRIN lens and an electrode. We validated the usefulness of this scaffold in chronic bimodal recording in an awake, behaving mouse. This method also allows for subsequent recovery and re-using of the lens and electrode to make it cost-efficient. We present three examples of opto-electrical bimodal recording to provide the ideas of how these methods can be implemented in different lines of studies.
Results
We show three methods of bimodal recording, in each of which we combined optical imaging through a GRIN lens and a custom-made microscope (Fig. 2) with different ways to record electrical activity. For each approach, we show an example recording result.
Bimodal recording: LFP and astrocytic calcium activity
The first approach is the simplest and uses a set of four insulated stainless steel wire electrodes secured to the side of a GRIN lens (Fig. 3). Each electrode was placed inside a flexible polyimide tubing cannula. The tips of the electrodes were extended by approximately 150 µm from the bottom surface of the GRIN lens. The working distance of the GRIN lens (from its bottom surface to a focal plane) is 100–300 µm. Therefore, in this arrangement, we can record optical and electrical signals from similar depth below the GRIN lens.
Using this bimodal recording method, we imaged calcium signalling activity of astrocytes while electrically recording LFP at the same time. We selectively expressed genetically encoded calcium indicator GCaMP6f in astrocytes by injecting a viral vector containing a regulatory element from the GFAP gene. One week later, we implanted the GRIN lens-electrode assembly in a way that its bottom surface was immediately above the aspirated surface over the CA1 (Fig. 4a) so that we could perform bimodal recording from the CA1 pyramidal cell layer. After another week, we observed fluorescence changes in large, dispersed area, which was probably from astrocytes out of the focal plane (Fig. 4b). We also observed that well-defined individual astrocytes showed clear changes in GCaMP6f fluorescence (Fig. 4c: blue, yellow, green).
While the optical recordings were performed, we also monitored LFP through the four implanted electrodes in the CA1 area. We detected typical patterns of neural activity in the CA1 area such as sharp waves and ripples, as clearly shown in band-pass filtered traces in Fig. 4d (150–250 Hz). By comparing the simultaneously recorded bimodal signals, we were able to examine the correspondence between the calcium dynamics in astrocytes and different activity patterns in the LFP (Fig. 4d).
Bimodal recording: LFP and neuronal calcium activity in CA1 pyramidal cells
In the second approach, we combined a GRIN lens and a silicon probe (Fig. 5). We made a custom-made microdrive and mounted a silicon probe on it. In this way, we were able to move the silicon probe deeper into the brain after it was chronically implanted. We prepared the GRIN lens and the microdrive-probe assembly separately and implanted them together in a surgery (See Materials and Methods; Fig. 5).
Using this approach, we imaged calcium signalling activity in neurons and electrically recorded LFP in the CA1 area (Fig. 6). For this purpose, we first injected a mouse with a viral vector containing the regulatory element from the CaMKIIα gene to express GCaMP6s in neurons in the CA1 area. One week later (day 0), we chronically implanted the mouse with a GRIN lens above the CA1 area and placed a silicon probe, attached to a custom-made microdrive assembly, immediately below the lens (Fig. 6a). We performed bimodal recording for > 1 month after implantation. During the recording sessions, we head-fixed the mouse above a running wheel; the mouse had periods of running and immobility.
On day 12, we performed bimodal recording. By this recording session, we had advanced the silicon probe ~ 500 µm forward from the surface of aspirated brain tissue along the longitudinal axis of the shanks. We found three evenly spaced dark areas near the edge of the GRIN lens (Fig. 6b, top), which indicates the existence of three silicon probe shanks closely under the GRIN lens. The shanks continued to be visible until day 34 (the last recording session performed in the awake mouse) and day 39 (the last recording session performed under anaesthesia). We confirmed the location of the GRIN lens and silicon probe shanks in brain sections prepared after we completed the experiments (Fig. 6b, bottom). Three shanks were located ~ 100 µm or less below the bottom surface of GRIN lens. Another one was located around the edge of the GRIN lens; this seems to be why we observed only three of the four shanks through the GRIN lens.
We observed many GCaMP6s-expressing neurons (Fig. 6c,d, Supplementary video 1). We recorded calcium signalling activity, starting from day 12 until we performed the last recording session on day 39. The GCaMP6s signals in neurons had clear boundaries corresponding to their cell bodies (Fig. 6c). We observed calcium events more frequently in individual neurons (Fig. 6d) than in astrocytes (Fig. 4). These events showed relatively sharp rise and slower decay and lasted for up to several seconds (Fig. 6d), which are typical features of GCaMP6s fluorescence changes in neurons.
Using the silicon probe, we monitored LFP. On the day of implantation, we advanced the silicon probe tips 450 µm forward from the surface of aspirated brain tissue along the longitudinal axis of the shanks. We detected sharp waves, which is a typical electrophysiological feature in the hippocampal CA1 area. We continued to observe sharp waves and/or sharp-wave-associated ripples until the last day of experiment (Fig. 6d).
Data shown in Fig. 6c–e are an example of bimodal recording on day 32. We were able to compare local field potential and calcium signalling activity in individual neurons, for example, whether or not the occurrence of calcium signalling events in individual neurons corresponds to the period around sharp-wave-ripples (Fig. 6d). Theta oscillations were observed while the mouse was running on the running wheel (Fig. 6e), during which some of neurons showed calcium events. Although it is not in the scope of our current study, it would be interesting to examine how LFP oscillations at different frequency ranges correspond to calcium events in neurons in the CA1 area.
Thus, we successfully performed chronic bimodal recording of LFP and neuronal calcium signalling in the same brain area in awake, behaving mice.
Bimodal recording: single-unit/neuronal calcium with a custom-designed 3D Printed scaffold
Whereas we managed to accurately place a silicon probe under the GRIN lens, we also found it challenging to consistently achieve the precise placement of the two separate components together during the surgery. Indeed, we experienced some failures in the precise placement of electrodes under a GRIN lens in test experiments that we did not describe in Fig. 6. To insert a silicon probe into the brain tissue at as a close position to a GRIN lens as possible, we needed to move the silicon probe while visually tracking its position under a stereomicroscope. The insertion site was inside an aspirated hole made in the brain tissue through craniotomy. Therefore, it was difficult for us to visually determine the insertion site immediately next to the GRIN lens.
In view of these challenges, we set out to devise the third approach that makes it easier to implant a silicon probe electrode and a GRIN lens precisely and minimize the variability from one implantation to another. For this purpose, we developed a 3D printed scaffold to hold a silicon probe and a GRIN lens together. We started this effort by adopting a microdrive assembly designed by Chung et al.12 and modified it to accommodate a GRIN lens and other specific requirement for our purpose (Fig. 7).
This scaffold is composed of three main pieces: “slider”, “body”, and “shell” (Fig. 7a). The scaffold houses a GRIN lens and a silicon probe and works as a microdrive moving the electrode into the brain. The scaffold is attached to a backpiece and a head-plate (Fig. 7b). The backpiece and head-plate accommodate a connector for the silicon probe and a cap. The cap covers the scaffold and protects it from mechanical damage while a mouse is in its home cage. It can be detached during experiments (Fig. 7c). The scaffold and connecter are placed at an angle so that they do not block the access of an objective lens to the GRIN lens. The entire assembly is secured to a head fixation holder, which we use to fix the mouse head under the microscope (Fig. 7b). The whole assembly is lightweight (6.8 g) and does not affect the mobility of the mouse to engage in its normal activity inside or outside of the home cage.
Using the scaffold, we performed calcium imaging, LFP and unit recording in the CA1 area of a Thy1-GCaMP6f mouse (Fig. 8a). During recording, we head-fixed the mouse on a treadmill. The mouse sometimes ran and sometimes stayed still. Using this method, we were able to place a silicon probe accurately within and/or slightly below the imaging volume of a GRIN lens, which we confirmed in brain sections prepared after we completed the bimodal recording experiments (Fig. 8b). We found the trace of the silicon probe shanks ~ 200–350 µm below the bottom surface of the GRIN lens.
On the day of implantation (day 0), we inserted the silicon probe into the brain tissue by rotating the driving screw for 1.5–2 turns. We detected sharp waves as well as spiking activity; however, the recording quality of spiking activity was not sufficient for spike sorting and we failed to isolate single unit activity. On day 15, we advanced the electrode 60 µm forward and performed the first bimodal recording. We detected sharp waves, ripples, and spiking activity (low quality again). In optical imaging, we detected dozens of neurons showing changes in GCaMP6f fluorescence. We continued to observe such neuronal calcium signalling activity throughout the period of the experiment. Figure 8c,d show an example result of bimodal recording on day 17. We succeeded in detecting single-unit spiking activity that were well isolated. Because these bimodal recording data may contain signals from the same individual neurons, we visually searched for a pair of electrical and optical neuronal data that showed a high degree of temporal matching. However, we did not find such an example in the limited number of sessions in this mouse. We continued to detect well-isolated single unit activity over several days. As expected, individual calcium signalling events visualized by GCaMP6f signals here were shorter compared with GCaMP6s signals in Fig. 6.
After we finished the experiment, we retracted the slider and withdrew the probe tip from the brain. Then we disconnected the slider and body from the shell by loosening the screw that had fixed them together. In this way, the assembly of the slider, body and silicon probe could be reused in next experiments. We intentionally designed the scaffold so that the recovery procedure would become easy.
Thus, using a 3D printed scaffold, we were able to chronically record LFP and single-unit activity electrically and simultaneously image GCaMP6f signals optically. This approach also simplifies the assembly, implantation and recovery of the recording probe.
Discussion
In this study, we demonstrated the successful use of three different methods of opto-electrical bimodal recording of neural activity in awake mice. Placing simple wire electrodes or a more sophisticated silicon probe in the proximity of a GRIN lens, these methods allowed us to monitor calcium signalling activity in neurons or astrocytes while simultaneously recording LFP and/or neuronal spiking activity. Although many readers may not be familiar with building a microscope, the full description of required parts in Table 1 would be helpful for the first-time builders. The total cost of microscope components (excluding an objective lens and a camera) is ~ 3500 US dollars. Although we used a relatively high-end objective lens and camera, the use of lower-end models would be sufficient for many applications. Alternatively, an objective lens and a camera available in an existing fluorescence microscope can be used. Thus, our opto-electrical bimodal recording method in awake head-fixed mice is a viable option that is relatively low cost and easily implemented.
We designed our methods with the motivation to perform bimodal recording from the same area in the brain. Therefore, the accurate placement of the GRIN lens and electrodes is essential. In Fig. 4, we used the simple solution of attaching electrodes to the side of a GRIN lens. In the course of testing the second approach described in Figs. 5 and 6, we experienced a challenge in the precise placement of the silicon probe immediately below the GRIN lens. Precise placement is also important in terms of not damaging the expensive silicon probe, which is so fragile that the probe can be easily damaged by mistakenly hitting other components. This challenge motivated us to design a scaffold to accommodate a GRIN lens and a silicon probe together. As shown in Fig. 7, we designed and constructed the 3D-printed scaffold, which simplifies the assembly, implantation and recovery procedures and ensures the accurate placement of the lens and the probe.
For successful bimodal recording with a silicon probe (Figs. 6 and 8), it is important to achieve proper spatial arrangement among a GRIN lens, a silicon probe and a target brain area. We designed our implantation scheme with the following considerations. First, because we used the GRIN lens that has a working distance of ~ 100–300 µm, the GRIN lens needs to be implanted 100–300 µm above the target area. As shown in Figs. 6 and 8, we successfully placed the GRIN lenses in this distance range, although some portions of the pyramidal cell layer were found to be too close to or far from the GRIN lens in Fig. 7. Second, electrodes should be placed at some distance below the target brain area. This is because (1) electrical recording works from a distance (single-unit: ~ 50 µm, multi-unit: ~ 140 µm)13, (2) the close placement of electrodes causes physical damage of the target brain area and (3) the silicon probe shanks may block the optical imaging of cells below them. Considering that the target structure is above the shanks, we implanted the silicon probe in a way that its electrodes face upward, thereby being closer to the neurons above them. Most recording sites estimated from histological analysis both in Figs. 6 and 8 were located in the position that we aimed at, although a few of the four shanks in each case were off. We observed the shanks of the silicon probe through the GRIN lens in Fig. 6, but not in Fig. 8. This difference is likely due to their difference in distances between the GRIN lens and the shanks; the shanks in Fig. 8 seem to have entered the volume below the GRIN lens more deeply than in Fig. 6. Although it is helpful to be able to confirm the position of electrodes during the experiment, the positioning of the shanks too closely to the GRIN lens may not be ideal because of tissue damage as mentioned above.
We have presented our successful bimodal recording of LFP and neuronal/astrocytic calcium signalling. LFP provides critical information to define how a local neuronal network is functioning. Bimodal recording would be an essential tool for investigating how the functional states of a local neuronal network modulate astrocyte calcium signalling. For example, the involvement of astrocytes has been suggested in the generation of sharp waves and ripples14 and theta oscillations15 in the hippocampus. Further investigation of such possibilities requires to characterize how astrocytes are activated during sharp waves and ripples or theta oscillations; therefore, bimodal recording is critical for such studies. In addition, it has been suggested that adult neurogenesis in the dentate gyrus is regulated by local circuit activity16,17,18. Bimodal recording of local neuronal activity/LFP and calcium signalling in radial glia/neural stem cells would help understand how neural activity regulates adult neurogenesis. Furthermore, optical imaging allows us to reveal spatial distribution/pattern of activated neurons in a brain region of interest. Bimodal recording can be applied to determine how such spatial characteristics of local circuit activation are associated with LFP-defined functional states.
One potential application of this approach is to perform bimodal recording of the same individual neurons. To achieve it, we need to temporally compare the electrical and optical recording data from individual neurons and identify a pair of individual neuronal data that show a good match in the timings of their firing and calcium events. In this way, one can optically identify neuronal types (if a genetically-encoded indicator is expressed in a specific neuronal type) and electrically record neuronal spikes representing individual action potentials. In addition, it is of importance to clarify whether calcium signalling events and action potentials have one-to-one correspondence or if not what patterns of action potential firing result in calcium signalling events. In this study, we only imaged green fluorescence of GCaMP6s and GCaMP6f using a GFP/FITC filter set. Optical imaging for a different wavelength can be implemented by using an appropriate LED light source and a corresponding filter set. The use of dual band filters, multi-wavelength light source (e.g. a mercury lamp) and a color camera allows us to perform simultaneous dual color imaging. This approach would enable, for example, to monitor activity of cell populations that express different fluorescent tags in the same brain region. For example, simultaneous imaging of GCaMP and RCaMP signals together with electrical recording is feasible. Fluorescence energy transfer (FRET) imaging can be implemented using an appropriate filter set. While we used a low-cost, custom-made microscope, our bimodal recording approaches can be combined with more sophisticated imaging hardware such as two-photon microscopy19.
Another potential application of this approach lies in the use of new genetically encoded fluorescent probes which can monitor a wide variety of molecules involved in multiple brain processes, such as GABA20, norepinephrine21, ATP22, and Dopamine23. Because these newly developed tools have excitation/emission spectra similar to that of GFP, little to no modification would be necessary for the present approach to investigate the relationship among neuronal spiking activity, LFP patterns, and the temporal dynamics of synaptic release of specific neurotransmitters or other brain processes.
In conclusion, we devised three opto-electrical bimodal recording approaches to target a deep brain structure using electrodes and GRIN lens and demonstrated that these three bimodal recording methods are viable approaches in awake head-fixed mice. This approach is affordable and versatile and can be adapted to a wide variety of setups for different lines of research, by harnessing the strengths of both electrical and optical recording.
Materials and methods
Microscope assembly
We built a custom-made microscope (Fig. 2) (Pierce et al., 2010). Table 1 lists parts of the microscope. We designed the microscope in a way that an objective lens can be precisely moved in the X and Y axes and for tilt. The objective lens faces downwards to acquire images through a GRIN lens implanted vertically on the skull of a head-fixed mouse. Excitation light was provided by a power-adjustable, light-emitting diode (470 nm, 650 mW mounted LED, Thorlabs Inc., New Jersey, United States). Fluorescence images were captured by an ORCA-Flash4.0 V3 C13440-20CU Digital CMOS Camera (Hamamatsu Photonics, Iwata, Japan) and HCImage live software (version 4.6.1.3, Hamamatsu Photonics, Iwata, Japan, https://hcimage.com/) through an emission filter (central wavelength: 530 nm, band width: 43 nm).
Subjects
All experimental procedures involving live mice were performed according to NACLAR guidelines and the approval by the IACUC at Nanyang Technological University, and are reported in accordance with ARRIVE guidelines (https://arriveguidelines.org). We used C57Bl/6 mice for Figs. 4 and 6 and a Thy1-GCaMP6f transgenic mouse (C57BL/6 J-Tg(Thy1-GCaMP6f)GP5.17Dkim/J, the Jackson laboratory, USA) (Dana et al., 2014) for Fig. 8. All the mice used were male and approximately 4 months old at the time of the surgery. We housed all mice in transparent acrylic cages in a temperature and humidity-controlled environment (20–22 °C, 50–60% humidity) on a 12-h light/dark cycle with ad libitum access to food and water unless otherwise stated. After the surgery, we housed mice individually. We used water as a reward to motivate the mice to run on a treadmill under the microscope. For this purpose, we restricted the amount of water given to the mice starting 3 days before placing the mouse in a treadmill. We adjusted the volume of water given to the mice so that they ran well on the treadmill, while keeping at least 85% of ad libitum body weight.
Lens-electrode assembly
For Fig. 4, we used a lens-electrode assembly consisting of a GRIN lens (1.0 mm diameter, 4.0 mm length, Inscopix, CA, USA) attached to four stainless steel (0.075 mm Φ. GoodFellow Cambridge Limited, England) wire electrodes at its side (Fig. 3a). We made four grooves on the cuff of the GRIN lens, through which four flexible polyimide tubing cannulas (0.20 mm Φ. MicroLimen, USA) passed. We attached cannulas to the side and cuff of the GRIN lens with glue (Loctite 401, Henkel Corporation, Germany). We removed insulation material from the tips of insulated stainless wires to use them as electrodes and inserted them individually into each cannula. We cut the wires so that the electrode tips extended ~ 150 µm from the bottom of the lens. The other ends of the wires were connected to the metal pins of a connector that was cut out from a VersaDrive 8 drive (Neuralynx, Inc., MT, USA) (Fig. 3b). In addition to the wires used as electrodes, two additional wires were connected to this modified connector, and we stripped their ends of the insulation. These wires were later soldered to the wires attached to ground screws to be used as reference electrodes.
For Fig. 6, we used a silicon probe electrode (Buzsaki 32, HC32_21mm, Neuronexus, MI, USA), which we attached to a custom-made microdrive assembly (Fig. 5a). We made the microdrive by cutting away a part of potentiometer (3006P Rectangular Multi-Turn Potentiometers, Vatronics Technologies Limited, USA), so that its screw was exposed (Grohrock et al., 1997). We applied the Metabond glue around the screw to make a small cube (we call it “a glue adaptor”), which moves when we rotate the screw; a full turn of the screw moves the adaptor ~ 300 µm. We attached a nut to the glue adaptor, to which we fixed a probe tip holder by another screw (Fig. 5a). We cut plastic plates to make a connector holder and microdrive holder (Fig. 5a), which we assembled together by two sets of nuts and bolts. We attached the microdrive to the microdrive holder (Fig. 5a) and glued the connector of a silicon probe electrode to the connector holder and the plastic part of the tip (but not the shanks or ribbon cable part) of the silicon probe to the probe tip holder (Fig. 5b). Before implantation, we cleaned the tips of the probe in a 10% solution of Decon 90 (Decon Laboratories, UK) in ddH2O for 90 min and then rinsed it with ddH2O. We confirmed that the channels in the probe were functional by measuring their impedance values using a NanoZ device (Neuralynx, Inc., MT, USA). The GRIN lens was not attached to the microdrive assembly and implanted separately as described below.
For Fig. 8, we used a custom-made 3D printed parts: a slider, a body, a shell, a backpiece, a headplate, a drive holder and a cap (Fig. 7). These parts were 3D-printed with Stereolithography technology by a commercial service (Engineering Computer Services (S) Pte Ltd). They used Figure 4 Standalone printer (3D systems, Inc) and Figure 4 Rigid Gray material, and washed the printed parts, removed support structures and cured the printed parts in a UV box. Computer-aided design files for the 3D-printed parts are available on GitHub (https://github.com/AyumuTashiro/bimodal).
We assembled the slider, the body and the shell to form a scaffold to carry a silicon probe and a GRIN lens. We attached the slider to the body via a 00–90 machine screw (9/16"), which we call a driving screw. We inserted the driving screw from the top of the body and into the screw hole of the slider (Fig. 7a,i). The end of the driving screw protruded out of the body. We screwed it into a nut until the nut touched the body, so that the driving screw was stably fixed in the body but was still able to smoothly rotate. We cut the portion of the driving screw that extended beyond the nut and fixed the screw and the nut by soldering them together. Rotation of the driving screw drives the movement of the slider; one full turn of the screw corresponds to 450 µm movement. We attached two other nuts to the top part of the body with glue (Fig. 7a,i). Later, we used these nuts to fix the scaffold to a drive holder when we fixed the scaffold to the mouse skull (Fig. 7a,iv). We connected the body to shell via another 00–90 machine screw (9/16") (Fig. 7a,ii). We inserted the screw from the top of the body and screwed it into a nut on the shell. We turned the driving screw until the slider reached the lowermost position. We then glued the probe tip to the slider and the connector to the backpiece (Fig. 7a,ii). To avoid placing the probe’s ribbon under stress, from this point onwards, we temporarily attached the backpiece and connector on the shell using a small amount of Blu tack. We removed the cuff of a GRIN lens and inserted the GRIN lens into the GRIN lens holding hole of the shell (Fig. 7a,iii). Under a stereomicroscope, we adjusted the position of the GRIN lens so that its bottom end was approximately 150 µm above the probe tips when we moved the slider all the way down. We fixed the GRIN lens to the shell, applying super glue to the point of contact between the GRIN lens and the shell while avoiding covering the surface of the lens. Before implantation, we measured impedance values using a NanoZ device and cleaned the probe using Decon 90, as described previously for Fig. 6. Parallel to the drive assembly, we attached two nuts to the head plate. (Fig. 7b,i) and glued a head plate and a head-fixation holder together (Fig. 7b,ii; https://hhmi.flintbox.com/technologies/b9aab117-9114-48e0-9d62-fc929ed30675).
Virus injection
One week before the implantation surgery, we injected 1.0 µl of virus solution into the hippocampal CA1 area of mice [antero-posterior: 1.90 mm, medio-lateral: 1.40 mm from the bregma, dorso-ventral: 1.25 mm (for Fig. 4), 1.60 mm (for Fig. 6) from skull surface] at a rate of 0.2 µl/min using a syringe (Hamilton, Model 80100, Knurled Hub NDL) with a blunt ended needle (25 gauges, 2.75″/69.9 mm, point style 3; Hamilton, Reno, NV, USA). We used viral vectors expressing GCaMP6f under the control of the regulatory element from the GFAP gene (AAV5/pZac2.1 gfaABC1D-cyto-GCaMP6f, prepared by Addgene, a gift from Dr. Baljit Khakh, Addgene plasmid # 52925) for Fig. 4 and GCAMP6s under the control of the regulatory element from the CaMKIIα gene [prepared as previously described (Kitanishi et al., 2015)] for Fig. 6.
Implantation of lens-electrode assembly
Deep anaesthesia was induced in mice with a mixture of 4% isoflurane and 2 L/min oxygen and then maintained at 1.5% isoflurane in 0.8L/min oxygen flow. Once anesthetized, we injected analgesic buprenorphine (0.1 mL per 10 g of body weight) and local anaesthetic lignocaine (0.05 mL at the incision site) subcutaneously. We shaved the scalp of the mice and mounted their heads in a stereotaxic frame (KOPF Instruments, CA, USA). We made a midline incision of the scalp approximately 2.0 cm long in the antero-posterior direction using a scalpel. We attached a drill (H.MH-17018 FOREDOM Electric Co, USA) with a drill bit (0.5 mm diameter, Fine Science Tools, Canada) to the stereotaxic frame on top of the bregma. Next, we moved the tip of the drill bit 1.9 mm posteriorly and 1.4 mm laterally over the right hemisphere. At this location, we drilled the skull to make a shallow mark where we later made craniotomy. Then, we drilled six holes on the skull (Fig. 3c) using the same drill bit and inserted one screw into each hole. Before insertion, we soldered two of the screws, referred to as “ground screws”, to stainless steel wires. We used these ground screws as the reference for the electrophysiological recording. We used a trephine (1.8 mm diameter, Fine Science Tools, Canada) to cut out a circular piece of the skull with a center at the position where we had marked. However, we left it in place while disconnected from the rest of skull. After this step, we performed different procedures for individual experiments, which we describe below individually.
For Fig. 4, we removed the disconnected piece of skull using a bent 25-gauge needle. Through the craniotomy, we aspirated the cortical tissue and made a cylindrical space which the GRIN lens fit in. For aspiration, we used a blunt-end, curved 25-gauge needle connected to an aspiration pump (913 MityFlex, World Precision Instruments, FL, USA). We hovered the needle closely over the tissue in a circular motion while constantly applying saline solution and monitoring the extent of the aspiration under the stereomicroscope. We continued to perform aspiration until reaching white fibres passing medio-laterally, a feature identifying the corpus callosum. We then continued to aspirate the tissue until we observed fibres passing in the antero-posterior direction. We continued to administer 0.9% saline solution and aspirated it repeatedly until the bleeding stopped.
We held the GRIN lens-electrode assembly (Fig. 3a) using a Proview kit adaptor (Inscopix, CA, USA) attached to the stereotaxic frame. We placed the GRIN lens-electrode assembly over the medial side of the craniotomy so that the lower surface of the lens was at the same height as the edge of the craniotomy. We considered this depth as a reference depth. We raised the lens-electrode assembly, placed it above the centre of the craniotomy and lowered it to 1.25 mm below the reference depth. We applied Kwik-Sil (World Precision Instruments, FL, USA) to cover the space between the edge of the lens-electrode assembly and the brain tissue. After 5 min, the lens-electrode assembly and electrode connector were fixed to the mouse skull by applying the Metabond glue. During this procedure, we covered all implanted screws with glue, being careful not to cover the free end of ground wires connected to ground screws. Once the GRIN lens-electrode assembly was secured to the skull, we soldered the ground wires, connected to the ground screws, to the wires on the connector. We attached the head fixation holder to the skull using glue (Fig. 3b), being careful not to cover the central opening area (Fig. 3d) of the head-fixation holder. Once completed, we removed the mouse from the stereotaxic frame and waited for 3 days for recovery before starting water restriction.
For Fig. 6, while the piece of skull was kept in place, we placed the head fixation holder on top of the mouse skull and fixed it using the Metabond glue (Fig. 5c). During fixation, we covered all implanted screws with the Metabond glue while not covering either the central opening area of the head-fixation holder or the free end of ground wires connected to ground screws. After 15 min, we removed the disconnected piece of the skull using a curved 25G needle. We aspirated tissue in the same manner as described above for Fig. 3 but over larger area (Fig. 5e). Next, we attached the microdrive assembly to a stereotaxic manipulator. The shanks of the silicon probe were tilted to the posterior direction by ~ 40 degrees, measured from the horizontal plane. Once the bleeding from the aspirated tissue fully stopped, we placed the microdrive assembly above the mouse head near the craniotomy (Fig. 5d). We applied a mixture of mineral oil (Sigma-Aldrich M5904) and bone wax (Hospec Medical Equipment & Supplies, FL, USA, MFID: 903) over the shank part of the silicon probe but not within ~ 300 µm from the tips (Fig. 5e,i). We removed all excess saline. Next, we moved the stereotaxic manipulator so that the tips of the silicon probe were placed at the surface of the aspirated tissue and adjusted the position of the microdrive until the four tips of the probe touched the brain at the same time. We attached the microdrive assembly to the skull and the head-fixation holder with the Metabond glue. 15 min later, we turned the screw of the microdrive (Fig. 5d) and inserted the shanks of the silicon probe into the brain until it was approximately 450 µm deep into the brain tissue along the longitudinal axis of the shanks (Fig. 5e,ii.) Using a set of fine forceps attached to the stereotaxic arm, we placed the GRIN lens on top of the craniotomy and then carefully lowered it over the surface of the aspirated tissue as closely to the four tips of the silicon probe as possible without damaging them. Although the placement cannot be precise, this arrangement was expected to result in the placement of the GRIN lens 100–300 µm above the probe tip (Fig. 5e,iii.). We applied Dura-gel mix (Cambridge Neurotech, Cambridge, UK) in the space between the GRIN lens and the probe. After the Dura-gel dried, we applied the Metabond glue to the side of the GRIN lens to attach the GRIN lens to the skull and head-fixation holder (Fig. 5f,i.). Next, we connected ground wires to the ground cannula of the silicon probe. We built a plastic cover around the implant using plastic sheets cut out from weighing boats (Heathrow Scientific, IL, USA, product ID: 120710) to protect the implant (Fig. 5f,ii.) We estimated the anatomical position of the tips of silicon probe by tracking the number of turns of the screw as well as monitoring the changes in the features of LFP while lowering the probe.
For Fig. 8, we performed the same procedures as for Fig. 6 up to tissue aspiration (except the type of head fixation holder was different, and we made the cylindrical shape of aspiration as Fig. 4). Once the bleeding from the aspiration site stopped, we made another hole (Fig. 7di, green) overlapping with the one we made for brain aspiration (Fig. 7di, red). Using a drill bit, we made a mark at 2.9 mm posterior and 1.4 mm right of the bregma. With this mark at its center, we disconnected another circular piece of the skull using the trephine (Fig. 7d,i). Using a drill bit and a pair of forceps, we removed the disconnected piece of the skull. This posterior hole was for inserting the probe (Fig. 7d,iv.). We attached the scaffold to the drive holder (Fig. 7a,iv,ci) and fixed the drive holder to a stereotaxic manipulator. By moving the manipulator, we inserted the GRIN lens into the anterior hole, lowered it 1.25 mm below the reference depth and then applied Kwik-Sil in the same procedures as for Fig. 6 (Fig. 7d,ii,iii). 5 min later, we applied the Metabond glue to the bottom and sides of the shell to attach the scaffold to the skull and head-fixation holder. Once the cement had cured, we attached the back piece (holding the probe connector) to the back of the head-plate using a screw (00–90 x ¼” machine screw) as shown on Fig. 7ci.
We connected ground screws’ wires to the ground cannula of the silicon probe. Before inserting the probe into the brain tissue, we applied a small amount of bone-wax to the exposed part of the silicon probe shanks in the same way as for Fig. 6 (Fig. 5e) while making sure it does not touch the tips. We inserted the probe’s shanks into the brain by turning the driving screw (Fig. 7d,iii,iv). We prepared Dura-gel and applied it over the exposed brain tissue using a bent 25G needle, while being careful to only cover the space between the brain and the lens. Once we completed the surgical procedures, we detached the drive holder from the scaffold and placed a cap to cover the entire implant and then kept it in place using a screw (00–90 x ¼” machine screw) as shown on Fig. 7c,iii.
Recovery of a silicon probe and a GRIN lens for re-use
At the end of experiment shown in Fig. 8, we deeply anesthetized the mouse and mounted it on the stereotaxic frame. Then, we raised the slider to the topmost position. We attached the drive holder to the stereotaxic frame. We placed it on top of the body to align the screw holes of the body and drive holder. We then inserted two screws to secure the body to the drive holder (as indicated in Fig. 7,iv.). We unscrewed the back piece from the head-plate. We temporarily attached the back piece (glued together with the probe connector) to the drive holder using Blu tack. Finally, we removed the screw connecting the body to the shell (Fig. 7,ii). In this way, we fully detached the body, slider, silicon probe, probe connector and backpiece from the mouse. The shell, GRIN lens, head-plate and head-fixation holder remained on the skull.
We perfusion-fixed the mouse with 4% paraformaldehyde in 0.1 M phosphate buffer. We dissected out the piece of skull that held the remaining parts (the shell, GRIN lens, head plate and head-fixation holder) and incubated it in acetone on a shaker at room temperature, to dissolve/soften Metabond. After 6 h, we were able to easily separate the remaining parts from the skull using forceps. We moved metal pieces (screws and head-fixation holder) to a separate container to avoid damage to the rest of the parts. We incubated these parts in fresh acetone on a shaker at room temperature to further remove Metabond from the parts for at least six more hours. We placed these parts on a clean surface for drying. We removed any remaining piece of Metabond with fine forceps and rinsed the parts with 70% ethanol solution.
We rinsed the recovered silicon probe with ddH2O for 30 min, a 10% Decon 90 solution in ddH2O for 90 min and then with ddH2O for 10 min. Finally, we dipped the silicon probe in a 70% ethanol solution in ddH2O. After being dried, the silicon probe is ready to be re-used. We recommend one to check the impedance of individual channels of silicon probe and not to re-use ones in compromised quality. The 3D-printed parts can be often re-used, but it is important to check the absence of damages.
We routinely re-use GRIN lens for multiple implantations. After incubation with acetone described above, we perform additional cleaning. We dip surgical sponges (Sugi, item 30,601, Kettenbach GmbH & Co., Germany) in acetone and wipe the surface of GRIN lens and rinse it with ddH2O to ensure that we remove all traces of Metabond from the the side surface of lens. Finally, it is important to inspect each lens using a stereo microscope to check it for any sign of damage to the lens surface, which deteriorates the image quality. We do not re-use a GRIN lens with a sign of damage.
Calcium imaging
We fixed the head of the mouse by tightly securing the head-fixation holder to a clamp (Fixed-stage positioner designs, https://hhmi.flintbox.com/technologies/fe949d6d-2f87-43ea-b13e-461b558c870d) fixed to the stable parts of the running wheel or treadmill apparatus, depending on the experiments. Next, we moved the objective lens over the head of the mouse. We turned on LED at the minimal power setting and started imaging using the HCImage software (Hamamatsu Photonics K.K., Japan). Next, we adjusted the X–Y position of the objective lens on the top of the implanted GRIN lens by using a fine-adjustment knob (Fig. 2, Table 1) on the microscope assembly so that we observed the circumference of the GRIN lens. Then, we adjusted the Z position of the objective lens so that we observed fluctuations in the fluorescence signal, which corresponds to the activity of neurons or astrocytes. After finding these cells, we adjusted LED power (typically ~ 0.16mW/mm2 at the top surface of the GRIN lens) and image acquisition parameters so that image quality was optimal for each day of recording. We always used an exposure time of 50 ms and an acquisition rate of 20 frames per second. We corrected motion artifacts of the movies using the moco method in ImageJ24.
Electrophysiology
We performed electrophysiological recording using an HS-36 headstage amplifier, the Digital Lynx SX data acquisition system and Cheetah Software 5.7.0 (Neuralynx, Inc., MT, USA). Electrical signal was band-pass filtered at 0.1–9000 Hz for each channel of the electrode. For spike sorting, we used an automated clustering algorithm in klusta software (Rossant et al., 2016). We then manually curated the results using Kwik-gui (https://github.com/cortex-lab/phy/). For analysing sharp-wave ripples, we used Neuralynx CSC filtering tools (Neuralynx, Inc., MT, USA) to apply a band-pass filter of 150–250 Hz to LFP.
Data availability
The datasets generated during and/or analysed during the current study are available from the corresponding authors on reasonable request.
References
Buzsáki, G., Anastassiou, C. A. & Koch, C. in Nature reviews neuroscience. 13, 407–420 (2012).
Cobar, L. F., Yuan, L. & Tashiro, A. Place cells and long-term potentiation in the hippocampus. Neurobiol. Learn. Mem. 138, 206–214. https://doi.org/10.1016/j.nlm.2016.10.010 (2017).
Kitanishi, T. et al. Novelty-induced phase-locked firing to slow gamma oscillations in the hippocampus: Requirement of synaptic plasticity. Neuron 86, 1265–1276. https://doi.org/10.1016/j.neuron.2015.05.012 (2015).
Mols, K., Musa, S., Nuttin, B., Lagae, L. & Bonin, V. In vivo characterization of the electrophysiological and astrocytic responses to a silicon neuroprobe implanted in the mouse neocortex. Sci. Rep. 7, 15642. https://doi.org/10.1038/s41598-017-15121-1 (2017).
Heiney, S. A., Ohmae, S., Kim, O. A. & Medina, J. F. Neuromethods 39–71 (Humana Press Inc., 2018).
Lovett-Barron, M. et al. Multiple convergent hypothalamus-brainstem circuits drive defensive behavior. Nat. Neurosci. 23, 959–967. https://doi.org/10.1038/s41593-020-0655-1 (2020).
Kim, J., Matney, C. J., Roth, R. H. & Brown, S. P. Synaptic organization of the neuronal circuits of the claustrum. J. Neurosci. 36, 773–784. https://doi.org/10.1523/JNEUROSCI.3643-15.2016 (2016).
Dana, H. et al. Thy1-GCaMP6 transgenic mice for neuronal population imaging in vivo. PLoS ONE 9, e108697. https://doi.org/10.1371/journal.pone.0108697 (2014).
Pachitariu, M., Stringer, C. & Harris, K. D. Robustness of spike deconvolution for neuronal calcium imaging. J. Neurosci. 38, 7976–7985. https://doi.org/10.1523/JNEUROSCI.3339-17.2018 (2018).
Zhou, H. et al. Cholinergic modulation of hippocampal calcium activity across the sleep-wake cycle. Elife https://doi.org/10.7554/eLife.39777 (2019).
Liu, X. et al. Multimodal neural recordings with Neuro-FITM uncover diverse patterns of cortical-hippocampal interactions. Nat. Neurosci. 24, 886–896. https://doi.org/10.1038/s41593-021-00841-5 (2021).
Chung, J., Sharif, F., Jung, D., Kim, S. & Royer, S. Micro-drive and headgear for chronic implant and recovery of optoelectronic probes. Sci. Rep. 7, 2773. https://doi.org/10.1038/s41598-017-03340-5 (2017).
Henze, D. A. et al. Intracellular features predicted by extracellular recordings in the hippocampus in vivo. J. Neurophysiol. 84, 390–400. https://doi.org/10.1152/jn.2000.84.1.390 (2000).
Tanaka, M., Wang, X., Mikoshiba, K., Hirase, H. & Shinohara, Y. Rearing-environment-dependent hippocampal local field potential differences in wild-type and inositol trisphosphate receptor type 2 knockout mice. J. Physiol. 595, 6557–6568. https://doi.org/10.1113/JP274573 (2017).
Foley, J. et al. Astrocytic IP3/Ca(2+) signaling modulates theta rhythm and REM sleep. Front. Neural Circuits 11, 3. https://doi.org/10.3389/fncir.2017.00003 (2017).
Dong, J. et al. A neuronal molecular switch through cell-cell contact that regulates quiescent neural stem cells. Sci. Adv. 5, 4416. https://doi.org/10.1126/sciadv.aav4416 (2019).
Song, J. et al. Neuronal circuitry mechanism regulating adult quiescent neural stem-cell fate decision. Nature 489, 150–154. https://doi.org/10.1038/nature11306 (2012).
Faitel’berg-Blank, V. R. & Perevalov, G. M. Dynamics of the spike activity of neurons in the posterior region of the hypothalamus during exposure to microwaves. Fiziol Zh 25, 199–202. https://doi.org/10.1016/j.celrep.2021.109324 (1979).
Liput, D. J., Nguyen, T. A., Augustin, S. M., Lee, J. O. & Vogel, S. S. A guide to fluorescence lifetime microscopy and Forster’s resonance energy transfer in neuroscience. Curr. Protoc. Neurosci. 94, e108. https://doi.org/10.1002/cpns.108 (2020).
Marvin, J. S. et al. A genetically encoded fluorescent sensor for in vivo imaging of GABA. Nat. Methods 16, 763–770. https://doi.org/10.1038/s41592-019-0471-2 (2019).
Feng, J. et al. A genetically encoded fluorescent sensor for rapid and specific in vivo detection of norepinephrine. Neuron 102, 745–761. https://doi.org/10.1016/j.neuron.2019.02.037 (2019).
Lobas, M. A. et al. A genetically encoded single-wavelength sensor for imaging cytosolic and cell surface ATP. Nat. Commun. 10, 711. https://doi.org/10.1038/s41467-019-08441-5 (2019).
Patriarchi, T. et al. Ultrafast neuronal imaging of dopamine dynamics with designed genetically encoded sensors. Science https://doi.org/10.1126/science.aat4422 (2018).
Dubbs, A., Guevara, J. & Yuste, R. moco: Fast motion correction for calcium imaging. Front. Neuroinform. 10, 6. https://doi.org/10.3389/fninf2016.00006 (2016).
Acknowledgements
We thank Ms. Chong Hai Tarng and Mr. Mohammad Zaki bin Ibrahim for technical assistance and Dr.Yuan Li for helping data analysis. We made part of Figs. 1, 3, 4, 5 and 7 with BioRender.com. This work was supported by National Medical Research Council, Ministry of Health Singapore (NMRC/OFIRG/0046/2017), Ministry of Education, Singapore (MOE2015-T2-2-035, MOE2017-T3-1-002), and NIMBELS (NIM/02/2016).
Author information
Authors and Affiliations
Contributions
L.F.C. and A.T. designed research. L.F.C., A.K. and K.B. performed research. L.F.C. and A.T. analysed data, L.F.C. and A.T. wrote the paper.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Supplementary Video 1.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Cobar, L.F., Kashef, A., Bose, K. et al. Opto-electrical bimodal recording of neural activity in awake head-restrained mice. Sci Rep 12, 736 (2022). https://doi.org/10.1038/s41598-021-04365-7
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-021-04365-7
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.