Abstract
We present a detailed analysis of experimental study, which shows clear evidence of a twostage melting process of a quasitwodimensional dusty plasma system in a highfrequency gas discharge. We accurately calculated global parameters of the orientational and translational order, as well as their susceptibilities to determine two critical points, related to “solidtohexatic” and “hexatictoliquid” phase transitions. The nature of the emerging defects and changes in their mutual concentration, in addition to the estimate of core energy of free dislocations also counts in favor of the formation of an intermediate hexatic phase. These results are fully consistent with the Berezinsky–Kosterlitz–Thouless theory.
Introduction
Twodimensional (2D) melting is still one of the unresolved entirely problems in condensed and soft matter physics^{1,2,3,4}, and over the decades two main competing theories, attempting to describe 2D melting, have emphasized main role of topological defects and grain boundaries. The first approach is Berezinsky–Kosterlitz–Thouless (BKT) theory^{5,6,7,8}, developed later by B. Halperin, D.R. Nelson and A.P. Young^{9,10} and transformed eventually to Berezinsky–Kosterlitz–Thouless–Halperin–Nelson–Young (BKTHNY) theory^{11}, which predicts twostep melting, from the crystal to liquid phase with formation of intermediate hexatic phase. It has short range translational and quasilongrange orientational order, and phase transitions are caused by the creation and dissociation, binding and unbinding of topological defects, such as disclinations and dislocations. Alternative theories consider a conventional firstorder phase transition from solid to liquid without the formation of any intermediate phase^{12,13}, assuming that the condensation of geometrical defects into grain boundaries and related aggregates is responsible for twodimensional melting.
Researchers have been looking for the evidence of hexatic phase among a wide range of twodimensional systems^{14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45}, including monolayers of electrons on the surface of liquid helium^{14}, polymer colloids^{15,16,17}, magnetic bubbles in thin films^{18,19,20}, liquid crystals^{21,22,23}, superconductors^{24}, as well as in dusty plasmas^{25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45}. Some experimental and numerical works have shown a good agreement with KTHNY theory^{25,26,27,28}, but others haven't. The reason of that might be in outofplane fluctuations^{29,30}, finitesize effects^{31,32} or different types of inhomogeneities, commonly observed in experiments during melting process. But the most crucial problem is concerned with the interaction range and stationarity of the system state. It is more complicated to get clear evidence of hexatic phase in systems with shortrange interactions (for instance, in dusty plasma systems with grains, interacting via Yukawa potential: φ(r) = eZ exp(− r/λ)/r, where λ is a screening length, and eZ is a charge of the particles) than with longrange potentials^{33,34,35}. In work^{36} the authors showed that the formation of an intermediate hexatic phase had been strongly dependent on the thermodynamic equilibration of the observed twodimensional system. More specifically, longrange or collective relaxation had taken much more time in comparison with that one, related to singleparticle local properties of the system.
First experimental studies of phase transitions in 2D dusty plasmas have been carried out by changing parameters of gas discharge^{37,38}, namely gas pressure or discharge power. That in turn led to a change of plasma parameters and confinement and therefore the interaction potential of dust particles in these structures. Further studies^{39,40} showed that in that case system exhibited nonequilibrium melting due to occurring of modecoupling instability. Other experimental studies^{41,42,43,44,45} presented different methods, none of which provided reliable degree of uniformity of heating of dusty plasma system as a whole. As the result, the authors concluded that the GBItheory was best suited to a description of melting of twodimensional dust structures, observed in their experiments. And finally, in our work^{28} we presented convincing evidence of formation of hexatic phase during 2D melting of dusty plasma system, which was experimentally observed for the first time.
Conventional analysis of any system near the phase transition points is much more complicated due to the growth of various fluctuations arising in this system. Standard approach, such as analysis of order parameter correlation functions, makes it possible to distinguish different phase states, but suffer ambiguities connected with finite size of the system and/or finite time of observation. Conversely, order parameter susceptibility method, presented in^{46} and applied in colloids^{17} showed to be robust to various uncertainties and enabled to clearly resolve phase transition points.
In this work, we introduce extended analysis of structural properties of 2D dusty plasma system, based on structure factor; discuss dynamics of topological defects together with assessment of core energy of free dislocations; and calculate order parameter susceptibility, which enabled us to determine accurately “solidtohexatic” and “hexatictoliquid” phase transition points.
Experiments
The experiments were performed in a RF discharge in argon at pressure P = 4.3 Pa, with discharge power W = 7.9 W. As dust component we used spherical monodisperse polystyrene particles, of density ρ_{d} = 1.05 g cm^{3}, with diameter 10.16 μm, coated with nickel of 200 nm in thickness. The scheme of the experimental setup is presented in Fig. 1. Main part of the experimental setup was vacuum chamber, which was preliminary pumped out and then filled by buffer gas up to working pressure. RF discharge was generated between two plane circular coaxial electrodes by highfrequency generator of 13.56 MHz with the use of impedancematching device. The distance between the electrodes was 5 cm. In the center of upper electrode there was a circular hole, which enabled us to record video in horizontal plane as well as to inject particles into discharge gap. After injection dust particles gained equilibrium negative charges because of ion and electron fluxes going to the particle surface until a stationary state is reached. Due to the balance of gravity and electrostatic force, providing a stiff vertical confinement, charged particle levitated above a flat horizontal rf electrode forming monolayer structures with negligible small vertical motions. To prevent the escape of particles in the horizontal direction metal ring with a height of about 2 mm and 100 mm in diameter was mounted on the lower (grounded) electrode; the ring formed a potential trap for the cloud of dust particles.
For visualization and external influence on the dusty plasma structure we used argon laser. The laser power varied in the range from 20 to 300 mW. In contrast to works^{40,41,42,43,44,45}, where uncoated particles were used and external action caused nonuniform heating, we used metalcoated particles with completely different response. Interacting with the metalcoated surface of particles, the laser light warmed them up, and a part of their surface became heated. Colliding with it, the neutrals of a buffer gas induced the photophoretic force^{47,48}. As the grains rotated due to the Brownian motion, this force uniformly acted on the whole surface of grains and, therefore, increased the energy of their chaotic motion, so that structure melted uniformly^{28}.
To be sure that metalcoated surface of particles didn't erode during experiment, we examined grains before and after discharge exposure by scanning electron microscopy. No any noticeable changes in the composition and surface properties were detected. At the same time, the original particles had small defects in the coating, which, nevertheless, was not dramatic for the possibility of obtaining a monolayer structure.
The movements of dust particles in the horizontal plane were recorded by a highspeed video camera with a frame frequency of 50–200 frames/s. The observed dust cloud consisted of a single dust layer with a number of particles up to 10^{4}. As the intensity of the laser radiation increased, the kinetic heating of the dust particles occurred, and the structure transferred from the crystalline to the liquid state. At this, to monitor the structure being a monolayer, we installed an additional CCDcamera to record particle movements in vertical direction through the side window of the discharge chamber. The obtained video images were processed using original computer programs, as a result of which the coordinates of the particles, their trajectories (see Fig. 2) and the speed of movements were determined.
The resulting velocity distribution of dust particles corresponded to the Maxwellian distribution function (within the experimental error), thus, for the dust component of the plasma the local equilibrium was observed and we could use term temperature to mean kinetic energy of motion (V_{T}^{2} = 2 T/M). At this there was a uniform redistribution of the velocities between the degrees of freedom (in a horizontal plane). Velocity variation in a measuring area was random and the errors didn’t exceed 7%. During the time of observation (10 s) a particle kinetic temperature, averaged over all particles in analyzed area, was also within the experimental error (~ 7%). Illustration of typical 1 s particle trajectories together with the velocity distribution profiles for different values of heating laser power is shown in Fig. 2.
From our point of view, there are two main reasons prevented from detection of twostep melting of 2D dusty plasma crystals in previous experiments of other authors: substantial inhomogeneity of melting process, causing temperature gradients and shear flows^{40,41,42,43,44,45}; and a little time for longrange relaxations before direct registration of the structural parameters of the analyzed dust structures^{36}.
To achieve the uniformity of the kinetic heating of dusty structure we expanded laser beam by cylindrical lens and then cut off nonhomogeneous parts of laser radiation by a diaphragm so that only the central part of widened beam with a uniformity of better than 95% reached dust particles. In addition, metalcoated particles moved chaotically rather than uncoated ones as a response to external force. At such conditions we observed an increase of particle kinetic energy without any evidence of any collective motions in a preferred direction, so that dusty plasma structure melted as a whole.
Before video recording dusty plasma structure has been kept under constant parameters of discharge and power of laser radiation during a time, sufficient for establishing not only stationarity and homogeneity of the system (which is commonly of about several seconds), but also for longrange relaxations within structure after starting laser exposure^{36}. (In our experiments it equaled ~ 5–10 min).
Another advantage of our method is the ability to vary precisely the power of laser radiation and thereby change with a small step dust kinetic temperature without loss of heating uniformity so that we obtained a big set of experimental «points» with slightly varied dust parameters and still constant plasma parameters. To sum up, long time for establishing stationarity and homogeneity of the system during experiments together with original precision method of manipulating the kinetic temperature of dust particles allowed us to fulfill conditions needed to «catch» hexatic phase, never observed before in dusty plasmas.
Methods and results
In order to avoid using of individual characterictics, specific to each experiment, and to make it possible to compare obtained data with numerical results, there is widely used effective coupling parameter Γ^{*} = 1.5(eZ)^{2}(1 + κ + κ^{2}/2)exp(−κ)/(T_{d}r_{p}), where κ ≡ r_{p}/λ is the screening parameter, r_{p} is the interparticle distance, T_{d} is the kinetic temperature of the particles^{49}. This parameter exhibits dimensionless properties for 2D—Yukawa systems, describing extended monolayer dusty plasma structures. Numerical calculations for twodimensional Yukawa systems show that the physical properties of such systems have two characteristic points of phase transitions^{25,26}. The first of these relates to the phase transition "liquid—hexatic phase" and occurs when the effective coupling parameter of Γ^{*} = 98 ± 4; the second point (at Γ^{*} = 154 ± 4) corresponds to the transition from the hexatic phase to the ideal crystal, where the diffusion coefficient of the particles tends to zero. In our experiment we determined the effective coupling parameter Γ^{*} by the first peak of pair correlation function^{49} within the accuracy of 5–10% (depending on Γ^{*}).
For the quantitative and qualitative description of the phase state of the system, as a rule, the analysis of pair g_{2}(r) and bondangular g_{6}(r) correlation functions is used, as well as the dynamics of various topological defects^{5,6,7,8,9,10}. For an ideal hexagonal structure the function g_{6}(r) ≡ 1, while it decreases with distance for other phase states of the system. The asymptotics of dimensionless pair g_{2}(r/r_{p}) and bondangular g_{6}(r/r_{p}) correlation functions can be used to analyze the phase state of the system^{27,28}. Thus, for twodimensional nonideal systems, the spatial decay of peaks of pair correlation functions in an ideal crystal is described by the power law g_{2} ∝ (r/r_{p})^{η} at η < 1/3, in the hexatic phase and the liquid, by the exponential dependence g_{2} ∝ exp(μr/r_{p}) at μ = μ_{h}≡ const and μ > μ_{h}, respectively. The bondangular correlation functions are characterized by a power asymptotic in the hexatic phase and exponential in the liquid phase.
As it has been shown in our previous studies^{25,26,27,28}, the value of the function g_{6}(r/r_{p}) is completely determined by the number of the appearing defects, that is why it is more convenient and reasonable to use normalized bondangular correlation function in the form of g_{6}^{*}(r/r_{p}) = g_{6}(r/r_{p})/N_{6}, where N_{6} is a fraction of particles with 6 nearest neighbors (see Fig. 3 in our work^{28}). There we presented three sets of clearly resolved curves with different slopes, corresponding to crystal, hexatic, and liquid phases as predicted by KTHNY theory: g_{6}^{*}(r/r_{p}) ~ Const for the range of effective coupling parameter Γ^{*} = 160–220, g_{6}^{*}(r/r_{p}) ~ r ^{η}_{6} at η_{6} = 1/5 for Γ^{*} = 110–140, and g_{6}^{*}(r/r_{p}) ~ exp(− r/ξ_{6}r_{p}) for Γ^{*} = 10–55, respectively.
In this paper we present important information about the phase states of the system under study, which can be obtained from the analysis of the diffraction pattern correlated with the configuration of the particles in this phase. For this purpose, the static structure factor s(k_{xy}) was calculated, defined as^{50}:
where k_{xy}—wave vector, r_{n} and r_{т}—radiusvectors for nth and mth particle on xyplane, correspondingly. Brackets < > define ensemble and time averaging. Figure 3 shows twodimensional static structure factor s(k_{xy}), calculated for various values of effective coupling parameters Γ^{*}, illustrating various diffraction patterns, specific to the solid (a), hexatic (b) and liquid (c) phases of the nonideal system. It is clearly seen that in the crystalline phase there are clear diffraction maximums corresponding to the hexagonal lattice. With increasing temperature the peaks become blurred up to forming hexagons, indicating the formation of an intermediate state, and then they form concentric circles, typical of the liquid phase.
Analysis of the asymptotic behavior of the correlation functions and diffraction patterns obtained from the calculation of the structural factor allows us to distinguish different phase states of twodimensional nonideal systems. However, it becomes less informative when considering asymptotics in the area of phase transitions, where the error in determining various thermodynamic and structural characteristics increases in close proximity to critical point of phase transition. In order to avoid the ambiguity of the analysis associated with fluctuations of spatial parameters and edge effects due to the finite size of the structure and averaging time, as well as to accurately determine the phase transition points, we used the method described in^{17}. It is based on the analysis of fluctuations of the bondangular and translational order parameters by calculating the susceptibilities of the corresponding global order parameters defined by the following formula:
Here L—size of the system under consideration, index α = 6, T defines bondangular and translational order, respectively, and \(\Psi_{\alpha } = \left {\frac{1}{N}\sum\limits_{j = 1}^{N} {\psi_{\alpha ,j} } } \right\)—global order parameter, determined as the local order parameter ψ_{α,j} averaged by all N particles j, taken in box of L x L size, given in average interparticle distances. Local order parameters for the particle j at position r_{j} = (x_{j}, y_{j}) are defined as:

(a)
for bondangular order \(\psi_{6,j} = \frac{1}{{N_{j} }}\sum\nolimits_{j = 1}^{{N_{j} }} {\exp (6i\theta_{j,k} )}\), where the sum on j is over all nearest neighbors N_{j} of the j^{th} particle, and an angle \(\theta_{jk}\) is formed by a bond, connected the k^{th} and the j^{th} particles, and a fixed axis;

(b)
for translational order \(\psi_{T,j} = \exp (i{\mathbf{Gr}}_{j} )\), where G—primary vector of the reciprocal lattice, determined by the peak of the twodimensional structure factor s(k_{xy}) for each temperature value.
For the liquid and hexatic phases, it is often difficult to determine magnitude of G. In this case, for the initial evaluation we used the value G, obtained for crystal phase, and then maximized the value of ψ_{T} by varying the vector G in the neighborhood of the initial estimate found from s(k_{xy}). Resulting value G was assumed optimal for a specific temperature value and was used in subsequent calculations of the global and local translational order parameter and the corresponding susceptibilities.
To calculate accurately the susceptibilities χ, it is necessary to collect sufficient statistics over time (in our case, the calculations were averaged over 2000 frames). To eliminate effects associated with the finite size of the structure, the calculation of χ_{L} was carried out in subboxes of various sizes L, and then was extrapolated in the thermodynamic limit to χ_{∞}. Starting from L = 30–40 interparticle distances (i.e. a region with 1500–2000 particles), the value of the parameter χ_{L} didn’t largely change (within 5% error), and tended to χ_{∞}, i.e. χ_{L} → χ_{∞}≡χ. Figure 4 (bottom) shows a plot of the translational, χ_{T}, and orientational susceptibilities χ_{6}, in dependence of the effective coupling parameter Γ^{*}.
One can see the jumps of the functions χ_{T} and χ_{6}, marked by vertical dashed lines, which clearly indicate two points of phase transitions at Г^{*} ~ 100 and Г^{*} ~ 160, respectively. The susceptibilities calculated for regions with a smaller number of particles (of about 400–500) also had smaller, but still clearly detectable jumps at the same points for value Г^{*}. Thus, this method for analyzing the susceptibility of order parameters showed good persistence to edge effects and the possibility of its use not only for extended dusty plasma structures, but also for a relatively small number of particles, in contrast to the method based on the calculation and analysis of correlation functions and structure factor.
Let’s take a look more closely on the analysis of defects occurring in a twodimensional nonideal dusty plasma structure. For a hexagonal lattice, the most common defects are disclinations—isolated defects with 5 or 7 nearest neighbors, dislocations—5–7 pairs of disclinations, and dislocation pairs—5–7–5–7 quadruple disclinations. It is convenient to visualize the picture of emerging defects, as well as their evolution over time, using the Voronoi diagram. An illustration of the construction of the Voronoi diagram for an experimentally obtained dusty plasma structure with Γ^{*} ~ 140 is shown at Fig. 5.
According to BKTHNY—theory, unbinding of dislocation pairs to free dislocation (i.e. isolated 5–7 pairs of disclinations) cause “solidtohexatic” phase transition, and unbinding of dislocations to free disclinations (i.e. isolated 5 or 7folded particles) cause “hexatictoliquid” phase transition. The dislocation acts as an additional row of particles, which gives a nonzero Burgers vector^{3,11} and effectively destroys the translational order in the system, while keeping the orientational order (see Fig. 5a–d). Two oppositely oriented dislocations form a pair with a zero Burgers vector, which does not violate translational and orientational symmetry. Therefore, dislocation pairs can be formed due to thermal excitation even at low temperatures in the crystal. As for disclinations, they strongly violate both translational and orientational symmetry (see Fig. 5e), that’s why they appear at higher temperatures and almost absent in crystal.
We experimentally measured the relative fractions of free disclinations and dislocations (i.e. surrounded by 6folded particles) occurred in the system, depending on the effective coupling parameter Γ^{*} (see top of Fig. 4). The figure shows that in the crystalline phase the concentration of free defects is vanishingly small. With increasing temperature in the system (and therefore decreasing the value of the effective coupling parameter Γ^{*}), one can see a gradual increase in the concentration of free dislocations at Γ^{*} ~ 170, and then growth in the number of free disclinations at Γ^{*} ~ 110 begins.
Whereas this graph shows qualitatively that the melting process is connected with increase of defects, it doesn’t accurately determine the position of critical points. The problem is that the statistics inevitably includes dislocations that are not quite “free”, i.e. have a pair on the same line of the lattice, and thus have a zero Burgers vector (see Fig. 5b–d). Such dislocations rapidly evolve in time. In particular they present “hopping”, or collapsing, or forming a dislocation pair, or “running” along one line of the lattice for some distance from each other. Another problem is the high sensitivity of the calculation to systematic errors, since defects tend to form large clusters that can correspond to different numbers of free dislocations or disclinations. For example, a 6mer 5–75–75–7 can be counted as a single dislocation added to a dislocation pair, or as three dislocations with the codirected Burgers vectors. This may explain the fact that the growth of dislocations on the graph occurs a little earlier than the melting in the system. It can be assumed that, before melting some seed concentration of clusters of nonfree defects needed for the formation of stable free dislocations should be accumulated in the system. The same behavior was observed in colloids^{17}, but had never been seen in dusty plasma before. We should note, that we didn’t observe the clear process of “unbinding” of free dislocations to separate free disclinations, considered in BKTHNYtheory. The most common pattern was developing of dislocations to agglomerations, consisting of several 5 and 7folded particles. We presume that it happens because such formation of bigger defect on the base of “seed” dislocation costs less energy compared to creation of free disclination.
Finally, let’s consider the core energy of free dislocations, E_{c}, which is an essential parameter of the 2D system. According to the GrainBoundaryInduced melting (GBI) theory, firstorder phase transition (by the formation of a polycrystalline structure) preempts KTHNYscenario under the condition Ec < 2.84 k_{B}T. One can observe such situation, for example, in^{43}. The value of E_{c} can be obtained from the Boltzmann distribution of free dislocations:
where η− free dislocation density. However the complex structure of the occurring defects makes the determination of value η rather problematic, as it was mentioned above. The core energy can be roughly estimated by measuring the density of particles with the number of nearest neighbors other than six (1 − N_{6}), i.e. by taking into account all defects. Such a method was used earlier in^{51}, but at the same time it does not take into account the interaction of defects and leads to an overestimation of the number of dislocations, and hence an underestimation of the value of E_{c}:
The plot of the dependence of the magnitude \({{(1  N_{6} )} \mathord{\left/ {\vphantom {{(1  N_{6} )} {N_{6} }}} \right. \kern\nulldelimiterspace} {N_{6} }}\) on the effective coupling parameter Γ^{*}, which in this case acts as the equivalent of the inverse temperature 1/T (i.e. Γ* ~ 1/T) is presented in Fig. 6.
As one can see at Fig. 6, the experimental points fit well on a straight line, the angle of which yielded us estimation of the core energy E_{c}: E_{c} = 3.1 ± 0.1k_{B}T. The real value of E_{c} is higher, since the magnitude obtained from the plot is the lowerbound estimate. As can be seen from the obtained estimation, the measured value of E_{c} is obviously above the threshold value of 2.84k_{B}T predicted in^{12}, which is yet more proof that the melting process of twodimensional dusty plasma structures follows the BKT—scenario. Presented analysis shows that melting scenario is highly sensitive to the way applied to transfer 2D system from one phase state to another.
Conclusions
To summarize, we consider a method of kinetic heating of dusty plasma structures under constant plasma parameters of the discharge, based on the influence of enlarged homogeneous laser beam on entire dusty plasma system, resulting in melting of 2D dusty plasma crystal. Quantitative and qualitative analysis of static structure factor, local and global parameters of translational and bondangular order parameters, temperature dependence of various types of defects, as well as estimating core energy of free dislocations and construction of Voronoi diagrams show clear evidence of twostep process of melting from the crystal to the liquid phase with formation of intermediate hexatic phase, predicted by BKTtheory. Using translational and orientational susceptibilities we accurately identified «solidtohexatic» and «hexatictoliquid» phase transition points. Long time for establishing stationarity and homogeneity of the system during experiments together with precision method of manipulating the temperature of dust particles allowed us to observe the clear evidence of hexatic phase never seen before in laboratory dusty plasma systems.
References
Lyuksyutov, I., Naumovets, A. G. & Pokrovsky, V. TwoDimensional Crystals (Academic Press Inc, New York, 1992).
Nelson, D. R. Defects and Geometry in Condensed Matter Physics (Cambridge University Press, Cambridge, 2002).
Jose, J. V. 40 Years of Berezinskii–Kosterlitz–Thouless Theory (World Scientific, Singapore, 2013).
Thouless, D. J., Haldane, F. D. M., Kosterlitz, J. M., The Nobel Prize in Physics. Press release. https://www.nobelprize.org/prizes/physics/2016/pressrelease/ (2016).
Berezinskii, L. V. Destruction of Longrange order in onedimensional and twodimensional systems having a continuous symmetry group I. Classical systems. Sov. Phys. JETP 32(3), 493 (1971).
Berezinskii, L. V. Destruction of longrange order in onedimensional and twodimensional systems possessing a continuous symmetry group. II. Quantum systems. Sov. Phys. JETP 34(3), 610 (1972).
Kosterlitz, J. M. & Thouless, D. J. Ordering, metastability and phase transitions in twodimensional systems. J. Phys. C Solid State Phys. 6, 1181 (1973).
Kosterlitz, J. M. The critical properties of the twodimensional xy model. J. Phys. C Solid State Phys. 7, 1046 (1974).
Nelson, D. R. & Halperin, B. I. Dislocationmediated melting in two dimensions. Phys. Rev. B Condens. Matter 19, 2457 (1979).
Young, A. P. Melting and the vector Coulomb gas in two dimensions . Phys. Rev. B Condens. Matter 19, 1855 (1979).
Strandburg, K. J. Twodimensional melting. Rev. Mod. Phys. 60, 161–207 (1988).
Chui, S. T. Grainboundary theory of melting in two dimensions. Phys. Rev. B Condens. Matter 28, 178 (1983).
Kleinert, H. Disclinations and first order transitions in 2D melting. Phys. Lett. A 95, 381 (1983).
Glattli, D. C., Andrei, E. Y. & Williams, F. I. B. Thermodynamic measurement on the melting of a twodimensional electron solid. Phys. Rev. Lett. 60, 420 (1988).
Murray, C. A. & Wenk, R. A. Microscopic particle motions and topological defects in twodimensional hexatics and dense fluids. Phys. Rev. Lett. 62, 1643 (1989).
Marcus, A. H. & Rice, S. A. Observations of firstorder liquidtohexatic and hexatictosolid phase transitions in a confined colloid suspension. Phys Rev. Lett. 77, 2577 (1996).
Han, Y., Ha, N. Y., Alsayed, A. M. & Yodh, A. G. Melting of twodimensional tunablediameter colloidal crystals. Phys. Rev. E 77, 041406 (2008).
Seshadri, R. & Westervelt, R. Hexatictoliquid melting transition in twodimensional magneticbubble lattices. Phys. Rev. Lett. 66, 2774 (1991).
Zahn, K. & Maret, G. Dynamic criteria for melting in two dimensions. Phys. Rev. Lett. 85, 3656 (2000).
Kusner, R. E., Mann, J. A., Kerins, J. & Dahm, A. J. Twostage melting of a twodimensional collodial lattice with dipole interactions. Phys. Rev. Lett. 73, 3113 (1994).
Geer, R. et al. Liquidhexatic phase transitions in single molecular layers of liquidcrystal films. Nature 355, 152–154 (1992).
Zaluzhnyy, I. A. Structural studies of the bondorientational order and hexatic–smectic transition in liquid crystals of various compositions. Soft Matter 13, 3240–3252 (2017).
Mandle, R. J. et al. Condensation of free volume in structures of nematic and hexatic liquid crystals. Liq. Cryst. 46, 114–123 (2019).
Guillamón, H. I. et al. Direct observation of melting in a twodimensional superconducting vortex lattice. Nat. Phys. 5, 651–655 (2009).
Vasilieva, E. V. & Vaulina, O. S. Orientational order and formation of topological defects in two dimensional systems. JETP 117(1), 169 (2013).
Vaulina, O. S. & Vasilieva, E. V. Influence of topological defects on mass transfer processes in twodimensional nonideal systems. EPL 106, 65001 (2014).
Petrov, O. F. et al. Twodimensional phase transition in a strongly nonideal dusty plasma. JETP 120(2), 327–332 (2015).
Petrov, O. F. et al. Solid–hexatic–liquid transition in a twodimensional system of charged dust particles. EPL 111, 45002 (2015).
Gribova, N., Arnold, A., Schilling, T. & Holm, C. How close to two dimensions does a Lennard–Jones system need to be to produce a hexatic phase?. J. Chem. Phys. 135(5), 054514 (2011).
Qi, W., Gantapara, A. P. & Dijkstra, M. Twostage melting induced by dislocations and grain boundaries in monolayers of hard spheres. Soft Matter 10(30), 5449 (2014).
Binder, K., Sengupta, S. & Nielaba, P. The liquid–solid transition of hard discs: Firstorder transition or Kosterlitz–Thouless–Halperin–Nelson–Young scenario?. J. Phys. Condens. Matter 14, 2323 (2002).
Mak, C. H. Largescale simulations of the twodimensional melting of hard disks. Phys. Rev. E 73, 065104(R) (2006).
Lee, S. I. & Lee, S. J. Effect of the range of the potential on twodimensional melting. Phys. Rev. E 78, 041504 (2008).
Bernard, E. P. & Krauth, W. Twostep melting in two dimensions: Firstorder liquid–hexatic transition. Phys. Rev. Lett. 107, 155704 (2011).
Kapfer, S. C. & Krauth, W. Twodimensional melting: From liquid–hexatic coexistence to continuous transitions. Phys. Rev. Lett. 114, 035702 (2015).
Derzsi, A., Kovács, A., Donkó, Z. & Hartmann, P. On the metastability of the hexatic phase during the melting of twodimensional charged particle solids. Phys. Plasmas 21, 023706 (2014).
Melzer, A., Homann, A. & Piel, A. Experimental investigation of the melting transition of the plasma crystal. Phys. Rev. E 53, 2757 (1996).
Quinn, R. A. & Goree, J. Experimental test of twodimensional melting through disclination unbinding. Phys. Rev. E 64, 051404 (2001).
Ivlev, A. V. & Morfill, G. Anisotropic dust lattice modes. Phys. Rev. E 63, 016409 (2000).
Couedel, L. et al. Direct observation of modecoupling instability in twodimensional plasma crystals. Phys. Rev. Lett. 104, 195001 (2010).
Sheridan, T. E. Melting transition in a twodimensional complex plasma heated by driven acoustic instability. Phys. Plasmas 15, 103702 (2008).
Knapek, C. A., Samsonov, D., Zhdanov, S., Konopka, U. & Morfill, G. E. Recrystallization of a 2D plasma crystal. Phys. Rev. Lett. 98, 015004 (2007).
Nosenko, V., Zhdanov, S. K., Ivlev, A. V., Knapek, C. A. & Morfill, G. E. 2D Melting of plasma crystals: Equilibrium and nonequilibrium regimes. Phys. Rev. Lett. 103, 015001 (2009).
Hartmann, P. et al. Crystallization dynamics of a single layer complex plasma. Phys. Rev. Lett. 105, 115004 (2010).
Knapek, C. A., Durniak, C., Samsonov, D. & Morfill, G. E. Scalefree behavior of a 2D complex plasma during rapid cooling. Phys. Rev. Lett. 110, 035001 (2013).
Weber, H., Marx, D. & Binder, K. Melting transition in two dimensions: A finitesize scaling analysis of bondorientational order in hard disks. Phys. Rev. B 51, 14636 (1995).
Davies, C. N. Aerosol Science (Academic Press, New York, 1966).
Jovanovic, O. J. Photophoresis—light induced motion of particles suspended in gas. J. Quant. Spectrosc. Radiat. Transf. 110, 889 (2009).
Vaulina, O. S., Adamovich, X. G., Petrov, O. F. & Fortov, V. E. Evolution of the masstransfer processes in nonideal dissipative systems II: Experiments in dusty plasma. Phys. Rev. E 77, 066404 (2008).
Kittel, C. Introduction to Solid State Physics (Wiley, New York, 2005).
Qi, W. K., Wang, Z., Han, Y. & Chen, Y. Melting in twodimensional Yukawa systems: A Brownian dynamics simulation. J. Chem. Phys. 133, 234508 (2010).
Funding
The work has been carried out under the support of the Russian Science Foundation (Project # 201200372).
Author information
Authors and Affiliations
Contributions
E.V.V. and M.M.V. carried out the experiments and prepared all figures. E.V.V. wrote the main text of manuscript. O.F.P. analyzed results and developed the concept. All authors discussed and reviewed the manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Vasilieva, E.V., Petrov, O.F. & Vasiliev, M.M. Laserinduced melting of twodimensional dusty plasma system in RF discharge. Sci Rep 11, 523 (2021). https://doi.org/10.1038/s4159802080082x
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s4159802080082x
Further reading

Experimental evolution of active Brownian grains driven by quantum effects in superfluid helium
Scientific Reports (2022)
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.