Thank you for visiting nature.com. You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Formation of gigahertz pulse train by chirped terahertz pulses interference

Abstract

The state-of-art broadband THz sources can contribute to the development of short-range 6G communications. This paper has demonstrated the feasibility of forming the controllable sequence of THz subpulses in the temporal domain and the corresponding quasidiscrete spectrum by the interference of two THz pulses with an exponential chirp. Moreover, due to small time delay between these pulses the temporal and spectral structures are similar to each other (so-called “linkage relation”). This will benefit information encoding in the THz range. The calculated metrics for the prototype communication channel based on the proposed method are competitive with existing short-range THz CW channels.

Introduction

The maturity and commercialization of the fifth generation (5G) has already arrived1. 6G (6th generation wireless systems) – a technology that supposed 100 to 1000 times2,3 faster than 5G, is considered to come to our lives in the next ten years4. Fresh spectral bands as well as advanced physical layer solutions are required for future wireless communications and THz wireless technology is a potential candidate5,6,7,8,9. Usually optical frequency combs are used in IR optical communication systems providing high data rates for long distances10. In this case, a large number of channels can be created using spectrum-sliced supercontinuum (SSSC) by arranging the interference of the two pulses with ultra-broadband spectra11,12. In the THz range a typical method to generate THz spectral comb is THz generator pumped by a pulse train of fs laser pulses13. It has also been reported that the transmitted spectrum of a THz pulse through a multilayer filter could achieve sub-comb structure14. As a THz frequency comb, it can be used to measure the frequency of a continuous-wave THz with high precision15; is suitable for the source of THz wireless communication of wavelength division multiplexing16, and expected to be used in ultra-fast information transmission systems17. The use of pulsed THz sources is limited by strong free space losses due to the wide spectrum which does not overlap with atmospheric transparency window18. Therefore, THz links have been suggested to use pulsed sources for short distance indoor communications19,20, and to use continuous radiation sources for long distances21,22. The implementation of these techniques relies on ultra-fast modulation as well as encoding and decoding methods of THz wave, in which pulsed broadband THz technologies can make contributions23.

In the case of pulsed broadband radiation, the main aim is to create encoding methods based on wavelength division multiplexing (WDM). For instance, quasi-discrete THz supercontinuum, obtained via spectral interference of two THz pulses, can be used to achieve a data transfer rate of 34.1 Gb/s with 31 THz spectral lines24. In the NIR region, the profiling of the spectral structure and the corresponding pulse sequence with a THz repetition rate has been verified both experimentally and analytically25,26,27. The peculiarity of this approach lies in the fact that there is the pulse train corresponding to the profiling spectral structure (“linkage relation”) which helps to preserve transmitted data from corruption. In the case of pulsed THz radiation, which consists of a small number of oscillations28, the formation of these structures by aforementioned method occurs when the following conditions are met: the THz pulses should be carefully chirped and the time delay between them is shorter than their duration. In the THz range, chirping and pulse elongation can be accomplished by using hollow metal waveguides29.

In this paper, we show for the first time the possibility of forming a frequency comb and the corresponding temporal pulses sequence in THz frequency range. The “linkage relation” between the emerging temporal and spectral structures is shown. Thus, changes in spectrum will lead to similar changes in temporal domain. Using proposed method data rate of 225 Mbit/sec can be achieved. The communication channel based on this method is comparable with existing short-range THz CW channels30,31,32,33. However these results can be improved by implementing pump laser with higher repetition rate and adjusting the interferometer. This technique allows to create short-range communication network and devices which can operate at room temperature.

Results

The experimental part of the work was carried out on a setup consisting of a THz spectrometer with a Michelson interferometer (see Methods). The interferometer was used to form two fs pulses with a variable delay between them of a longer duration. The obtained fs pulses generated THz pulses by photo-Dember effect in InAs crystal. THz pulses, in turn, propagated in a hollow metal waveguide chirping and interfering. The presence of the chirp enables to observe not only the formation of a quasi-discrete spectrum24, but also the formation of a train of pulses during the interference26,27. This is possible due to the correct selection of conditions, namely, a small delay between pulses and the presence of a chirp with a known dependence. The chirp of experimentally obtained THz pulses is shown in Fig. 1(a) (red curve). As can be seen, it is well approximated by an exponential function (blue curve). THz pulse propagation through the waveguide can be described as a linear superposition of the coupled propagating modes. The parameters of the waveguide, as well as the characteristics of the THz radiation, determine the conditions for modes coupling and thus the appearance of the output radiation, for instance, its chirp. More details about physical interpretation can be found in29,34. Figure 1(b,c) illustrates the experimental quasi-discrete spectrum and the temporal structure of the formed pulse train.

It was previously shown26,27 that a linearly chirped pulse interfering with itself shifted by a time delay shorter than its duration formed a pulse train which had a strict corresponding relation to its quasi-discrete spectrum. This means that each subpulse in the temporal structure has its own spectral line in the quasi-discrete spectrum. In this paper, due to the exponential chirp in the THz spectrum, the presence of the correspondence between the temporal and spectral structures is not obvious. In Fig. 1(b) three discernible pulse spikes can be seen. In the temporal structure Fig. 1(c) these spikes correspond to three pulses of different frequencies and duration. The formation of an irregular temporal sequence is associated with a nonlinear (exponential) pulse chirp. Figure 1(c) shows that the duration of individual peaks in the sequence varies from 10 to 40 ps, which corresponds to a repetition rate of 25–100 GHz. In this case, the chirp determines the correlation between the temporal and spectral structures27. Moreover, encoding can be carried out in the spectral domain, where we have a regular quasidiscrete structure Fig. 1(b) formed by two-beam interference11. Encoding in this case, should be done in the spectral domain by separating the spectrum in space and using amplitude filters, as it was previously shown in NIR range26.

Discussion

To verify the assumptions made during the analysis of experimental data, a numerical simulation was carried out with parameters close to experimental ones. THz pulse with exponential chirp can be represented as:

$$E={E}_{0}\cdot \exp \left(-2\frac{{t}^{2}}{{\tau }_{0}^{2}}\right)\cdot \,\sin ({\omega }_{0}(1+\exp (-\alpha t))t)$$
(1)

where E0 is the pulse amplitude, ω0 = 2πv0 and v0 is the pulse central frequency, τ0 is the pulse duration, α is the inverse steepness of exponential chirp. To match the experiment, these parameters were chosen as follows: v0 = 0.45 THz, τ0 = 17 ps and α = 1/22 ps−1. The difference between pulse duration τ0 in numerical simulation and experiment is caused by the fact that a Gaussian pulse profile is used in the numerical simulation, while in the experiment the chirped THz pulse has an asymmetric non-Gaussian profile. Therefore, the pulse duration in the numerical simulation was increased to match the experimental pulse duration.

Figure 2(a,b) illustrates spectrum and temporal structure of the exponential chirped THz pulse obtained from numerical simulation. The interference of two pulses in temporal domain can be represented as26,27:

$${E}_{sum}=E(t)+E(t+\Delta t)$$
(2)

where Δt is the time delay between pulses. Figure 2(c,d) represents such pulse interference with itself shifted by the time delay Δt = 4 ps and the comparing of the corresponding quasi-discrete spectrum with experimental results (Fig. 2(c)). It can be seen that the simulated spectrum agrees well with the experimental one. As already noted, in the numerical simulation a Gaussian profile is used to describe the temporal structure. In the experiment, the temporal structure has an asymmetric non-Gaussian profile. In this regard, a comparison of these structures, as well as their interference is not indicative, since in the experiment asymmetric broadening with respect to the maximum occurs (see Fig. 5(c)), while the numerical simulation gives a symmetric broadening (see Fig. 2(b)).

To confirm the correspondence between the temporal and spectral structures formed during the interference, a numerical simulation of the removal of one line in the quasi-discrete spectrum was performed. The results are shown in Fig. 3. It can be seen that cutting out one of the spectral peaks leads to the vanishing of the subpulse in temporal structure. However, there is some ambiguity in temporal domain which can be explained by the presence of a residual interference term. This term can be eliminated by the proper selection of experimental parameters27. Thus, changes in spectrum lead to similar changes in temporal domain. In other words there is a “linkage relation” between spectrum and temporal structure of THz pulse train. It should be noted that in the case of two-beam interference, the position of the minima of the quasidiscrete structure in the spectral region, which is determined by the time delay between pulses, is fixed. The absolute value of modulated spectrum is described by the following expression11:

$$|{G}_{sum}(\omega )|=|{G}_{0}(\omega \mathrm{)|(1}+cos(\omega \varDelta t))$$
(3)

where Δt is a time delay between pulses and correspond to 3 ps in our experiment. The error associated with a double-pass of interferometer is equal to 2 μm (~6.7 fs). Therefore the accuracy of the minima position in the spectrum can be calculated as the ratio of the aforementioned value to the delay between pulses to be 0.2%. In addition, as mentioned above encoding and decoding take place in the spectral range. The positions of spectral minima are fixed, and will not be affected by the instability of driving laser energy and its duration that leads to the changes in the temporal domain. As a result, this will not affect the transmitted information.

In order to further clarify the application prospects of this method, we provide the channel parameters (by channel we mean one of the peaks in the Fig. 2(c), e.g. the central one) of the original unoptimized communication system for the future establishment of the communication system. The ratio of the signal at the carrier frequency to noise (C/N) is of the order of 103 or 30 dB. BER in the case of binary message sources, bit rate of 75 Mbit/s (which corresponds to the laser repetition rate of 75 MHz for binary message sources) and spectral channel width of 250 GHz is equal to 1.5 · 10−7. For 50 cm transmission, the link budget is calculated to be: Received Power (−94.7 dBm) = Transmitted Power (−15.2 dBm) + Gains (0 dB) - Losses (79.5 dB). Competitive with existing short-range THz CW channels (10−3–10−7 BER)30,31,32,33, the method is promising in further establishment of the communication system.

In conclusion, this paper has shown experimentally the feasibility of forming a variable sequence of THz subpulses with 25–100 GHz repetition rate in temporal domain. This is achieved by interference of two chirped THz pulses with a time delay less than their duration. As a result, the stable regular structure is formed in the spectral domain. The modulation frequency in the spectral and temporal structures is controlled by the time delay between the interfering pulses. Simulation-based results show that with the exponential chirped THz pulses, there is a “linkage relation” between the temporal and spectral structures. The data rate of such system is equal to the laser pulse repetition rate multiplied by the number of spectral peaks, in our case it is 75 · 3 = 225 Mbit/s. Estimated metrics of the communication channel based on the proposed method show that it is competitive with existing short-range THz CW channels. Due to active research both in the field of integrated chip lasers35, as well as in the development of miniature THz antennas36,37, this method of modulation, control and coding of broadband THz radiation in the temporal and spectral domain can be further improved and applied for short-range THz communication.

Methods

Figure 4 illustrates the experimental setup for THz pulse train generation from interference of two chirped THz pulses based on the conventional THz time-domain spectrometer38. In this system, the THz radiation is generated due to the photo-Dember effect in an InAs crystal located in 2.4 T magnetic field39. The Yb-doped solid-state fs oscillator (central wavelength 1050 nm, duration 100 fs, pulse energy 70 nJ, repetition rate 75 MHz) is used as a pump. The THz radiation has central frequency 0.3 THz, estimated average power 30 μW, and FWHM ~2 ps (see Fig. 5(a,b)). [100]-oriented CdTe crystal is used for electro-optical detection.

It is known that two-beam interference leads to quasi-discrete spectrum11. In our work Michelson interferometer in front of a THz generator is used to create two consecutive fs pulses. One of the mirror is fixed while the other is located on the linear stage which allow to adjust the time delay Δt between fs pulses. The time delay is chosen so that the THz pulses generated in the InAs crystal do not interfere with each other. Then these pulses pass through the hollow metal waveguide40, where they overlap in time and interfere (see inset of Fig. 4). As the result of the interference THz pulsed train and corresponding quasi-discrete spectrum are generated (see Fig. 1(b,c)). The time delay Δt with the fixed waveguide parameters allows to control the modulation in the temporal and spectral structures25.

Figure 5(a,b) show example of generated single THz pulse and its spectrum and Fig. 5(c,d) illustrate the chirped THz pulse obtained from hollow stainless steel metal waveguide with 23 mm length, 0.89 mm tip inner diameter, and 1.43 mm outer diameter.

As can be seen from the Fig. 5, chirping in a metal waveguide leads to an increase in the THz pulse duration from 2 ps to 7 ps (FWHM), while the corresponding spectrum shifts its central frequency to 0.45 THz and undergoes some minor changes. For example, at low frequencies there is a drop due to the fact that at these frequencies the signal does not propagate in the waveguide with such parameters. However, the water absorption line at a frequency of 0.55 THz remains unchanged. The 0.3 THz dip is also caused by the propagation features of THz radiation in the waveguide29,40,41.

References

1. 1.

Andrews, J. G. et al. What will 5g be? IEEE J. on selected areas communications 32, 1065–1082 (2014).

2. 2.

Zhang, Z. et al. 6g wireless networks: Vision, requirements, architecture, and key technologies. IEEE Veh. Technol. Mag. 14, 28–41 (2019).

3. 3.

Calvanese Strinati, E. et al. 6g: The next frontier: From holographic messaging to artificial intelligence using subterahertz and visible light communication. IEEE Veh. Technol. Mag. 14, 42–50 (2019).

4. 4.

Busari, S. A., Huq, K. M. S., Mumtaz, S. & Rodriguez, J. Terahertz massive mimo for beyond-5g wireless communication. In ICC 2019 - 2019 IEEE International Conference on Communications (ICC), 1–6 (2019).

5. 5.

Ummethala, S. et al. Thz-to-optical conversion in wireless communications using an ultra-broadband plasmonic modulator. Nat. Photonics 13, 519–524 (2019).

6. 6.

Huq, K. M. S. et al. Terahertz-enabled wireless system for beyond-5g ultra-fast networks: A brief survey. IEEE Netw. 33, 89–95 (2019).

7. 7.

Rappaport, T. S. et al. Wireless communications and applications above 100 ghz: Opportunities and challenges for 6g and beyond. IEEE Access 7, 78729–78757 (2019).

8. 8.

Cacciapuoti, A. S., Sankhe, K., Caleffi, M. & Chowdhury, K. R. Beyond 5g: Thz-based medium access protocol for mobile heterogeneous networks. IEEE Commun. Mag. 56, 110–115 (2018).

9. 9.

Boulogeorgos, A.-A. A. et al. Terahertz technologies to deliver optical network quality of experience in wireless systems beyond 5g. IEEE Commun. Mag. 56, 144–151 (2018).

10. 10.

Delfyett, P. J. et al. Advanced ultrafast technologies based on optical frequency combs. IEEE J. Sel. Top. Quantum Electron. 18, 258–274 (2012).

11. 11.

Alfano, R. R. & Zeylikovich, I. Method and apparatus for producing a multiple optical channel source from a supercontinuum generator for wdm communication US Patent 7,245,805 (2007).

12. 12.

Lu, X. & Zhang, X.-C. Investigation of ultra-broadband terahertz time-domain spectroscopy with terahertz wave gas photonics. Front. Optoelectronics 7, 121–155 (2014).

13. 13.

Li, H. et al. Dynamics of ultra-broadband terahertz quantum cascade lasers for comb operation. Opt. Express 23, 33270–33294 (ts).

14. 14.

Liu, P., Xu, D. & Yao, J. Analysis on characteristic and application of thz frequency comb and thz sub-comb. In Journal of Physics: Conference Series, vol. 276, 012218 (IOP Publishing, 2011).

15. 15.

Udem, T., Holzwarth, R. & Hänsch, T. W. Optical frequency metrology. Nature 416, 233–237 (2002).

16. 16.

Delfyett, P. J. et al. Optical frequency combs from semiconductor lasers and applications in ultrawideband signal processing and communications. J. Light. Technol. 24, 2701 (2006).

17. 17.

Kleine-Ostmann, T. & Nagatsuma, T. A review on terahertz communications research. J. Infrared, Millimeter, Terahertz Waves 32, 143–171 (2011).

18. 18.

Schneider, T., Wiatrek, A., Preußler, S., Grigat, M. & Braun, R.-P. Link budget analysis for terahertz fixed wireless links. IEEE Transactions on Terahertz Sci. Technol. 2, 250–256 (2012).

19. 19.

Piesiewicz, R. et al. Short-range ultra-broadband terahertz communications: Concepts and perspectives. IEEE Antennas Propag. Mag. 49, 24–39 (2007).

20. 20.

Han, C., Bicen, A. O. & Akyildiz, I. F. Multi-wideband waveform design for distance-adaptive wireless communications in the terahertz band. IEEE Transactions on. Signal Process. 64, 910–922 (2015).

21. 21.

Lin, C. & Li, G. Y. Adaptive beamforming with resource allocation for distance-aware multi-user indoor terahertz communications. IEEE Transactions on Commun. 63, 2985–2995 (2015).

22. 22.

Han, C. & Akyildiz, I. F. Distance-aware bandwidth-adaptive resource allocation for wireless systems in the terahertz band. IEEE Transactions on Terahertz Sci. Technol. 6, 541–553 (2016).

23. 23.

Dunn, A. et al. High-speed modulation of a terahertz quantum cascade laser by coherent acoustic phonon pulses. Nat. Commun. 11, 1–8 (2020).

24. 24.

Grachev, Y. V. et al. Wireless data transmission method using pulsed thz sliced spectral supercontinuum. IEEE Photonics Technol. Lett. 30, 103–106 (2017).

25. 25.

Tsypkin, A. N., Putilin, S. E., Okishev, A. V. & Kozlov, S. A. Ultrafast information transfer through optical fiber by means of quasidiscrete spectral supercontinuums. Opt. Eng. 54, 1–3 (2015).

26. 26.

Tcypkin, A. & Putilin, S. Spectral-temporal encoding and decoding of the femtosecond pulses sequences with a thz repetition rate. Appl. Phys. B 123, 44 (2017).

27. 27.

Melnik, M., Tcypkin, A., Putilin, S., Kozlov, S. & Rodrigues, J. J. Analysis of controlling methods for femtosecond pulse sequence with terahertz repetition rate. Appl. Phys. B 125, 98 (2019).

28. 28.

Kozlov, S. A., Drozdov, A. A., Choudhary, S., Kniazev, M. A. & Boyd, R. W. Suppression of self-focusing for few-cycle pulses. J. Opt. Soc. Am. B 36, G68–G77 (2019).

29. 29.

Gallot, G., Jamison, S. P., McGowan, R. W. & Grischkowsky, D. Terahertz waveguides. J. Opt. Soc. Am. B 17, 851–863 (2000).

30. 30.

Moeller, L., Federici, J. & Su, K. Thz wireless communications: 2.5 gb/s error-free transmission at 625 ghz using a narrow-bandwidth 1 mw thz source. In 2011 XXXth URSI General Assembly and Scientific Symposium, 1–4 (2011).

31. 31.

Ducournau, G. et al. 32 gbit/s qpsk transmission at 385 ghz using coherent fibre-optic technologies and thz double heterodyne detection. Electron. Lett. 51, 915–917 (2015).

32. 32.

Jia, S. et al. Thz wireless transmission systems based on photonic generation of highly pure beat-notes. IEEE Photonics J. 8, 1–8 (2016).

33. 33.

Zhao, M., Zhou, W. & Yu, J. 3.5 gbit/s ook thz signal delivery over 88 cm free-space at 441.504 ghz. Microw. Opt. Technol. Lett. 60, 1435–1439 (2018).

34. 34.

Mendis, R. Nature of subpicosecond terahertz pulse propagation in practical dielectric-filled parallel-plate waveguides. Opt. Lett. 31, 2643–2645 (2006).

35. 35.

Rafailov, E. U., Cataluna, M. A. & Sibbett, W. Mode-locked quantum-dot lasers. Nat. photonics 1, 395–401 (2007).

36. 36.

Barr, P., Zaman, A. & Miranda, F. A compact, broadband antenna for planetary surface-to-surface wireless communications. Microw. Opt. Technol. Lett. 48, 521–524 (2006).

37. 37.

Han, S.-P. et al. Compact fiber-pigtailed ingaas photoconductive antenna module for terahertz-wave generation and detection. Opt. express 20, 18432–18439 (2012).

38. 38.

Grachev, Y. V., Osipova, M. O. & Bespalov, V. G. Comparison of an electro-optical system and photo-conducting antenna employed as detectors of pulsed terahertz radiation by means of a new method for measuring spectral width. Quantum Electron. 44, 1170–1172 (2014).

39. 39.

Bespalov, V. et al. Methods of generating superbroadband terahertz pulses with femtosecond lasers. J. Opt. Technol. 75, 636–642 (2008).

40. 40.

McGowan, R. W., Gallot, G. & Grischkowsky, D. Propagation of ultrawideband short pulses of terahertz radiation through submillimeter-diameter circular waveguides. Opt. Lett. 24, 1431–1433 (1999).

41. 41.

Nazarov, M. M. et al. Eight-capillary cladding thz waveguide with low propagation losses and dispersion. IEEE Transactions on Terahertz Sci. Technol. 8, 183–191 (2018).

Acknowledgements

This work was partially supported by RFBR according to the research project No. 17-00-00275 (17-00-00272), by Ministry of Science and Higher Education of the Russian Federation project “Extreme phenomena and coherent structures in nonlinear physics”, by FCT/MCTES through national funds and when applicable co-funded EU funds under the Project UIDB/EEA/50008/2020, and by Brazilian National Council for Research and Development (CNPq) via Grants No. 431726/2018–3 and 309335/2017-5. The authors acknowledge Dr. M. Nazarov from NRC «Kurchatov Institute» and Dr. M. Song from ITMO University for fruitful discussions.

Author information

Authors

Contributions

X.L. and M.Z. analysed the results, M.M. performed numerical simulations, E.O. and A.T. conducted the experiment, J.R. prepared review of the existing works in the field of study, S.K. conceived the experiment. All authors reviewed the manuscript.

Corresponding author

Correspondence to Maria Zhukova.

Ethics declarations

Competing interests

The authors declare no competing interests.

Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and Permissions

Liu, X., Melnik, M., Zhukova, M. et al. Formation of gigahertz pulse train by chirped terahertz pulses interference. Sci Rep 10, 9463 (2020). https://doi.org/10.1038/s41598-020-66437-4

• Accepted:

• Published: