Skip to main content

Thank you for visiting You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

Pore-scale mechanisms of CO2 storage in oilfields


Rapid implementation of global scale carbon capture and storage is required to limit temperature rises to 1.5 °C this century. Depleted oilfields provide an immediate option for storage, since injection infrastructure is in place and there is an economic benefit from enhanced oil recovery. To design secure storage, we need to understand how the fluids are configured in the microscopic pore spaces of the reservoir rock. We use high-resolution X-ray imaging to study the flow of oil, water and CO2 in an oil-wet rock at subsurface conditions of high temperature and pressure. We show that contrary to conventional understanding, CO2 does not reside in the largest pores, which would facilitate its escape, but instead occupies smaller pores or is present in layers in the corners of the pore space. The CO2 flow is restricted by a factor of ten, compared to if it occupied the larger pores. This shows that CO2 injection in oilfields provides secure storage with limited recycling of gas; the injection of large amounts of water to capillary trap the CO2 is unnecessary.


With anthropogenic CO2 emissions into the atmosphere of 37 GtCO2 in 20181, fuelled by the growth in fossil fuel consumption2, any viable solution to avoid dangerous climate change has to involve the rapid and large-scale implementation of CO2 capture and storage (CCS)3,4,5,6,7,8,9. Although there are abundant CO2 storage sites in deep saline aquifers10, given the short time frame to implement the technology at a global scale, geological storage of CO2 in the next decade is most practical in depleted oil and gas reservoirs, where the infrastructure including facilities, pipelines, and injection wells, as well as detailed knowledge of the fields already exists, combined with an immediate financial incentive from enhanced oil recovery (EOR)11,12,13,14, see Fig. 1.

Figure 1
figure 1

Diagram showing carbon capture and storage coupled with enhanced oil recovery. (A) A schematic of CO2 storage in depleted oil reservoirs. The behaviour of CO2 underground is controlled by pore-scale processes. (BD) show real images of reservoir fluids trapped in a single pore of carbonate rocks at elevated temperatures and pressures. CO2 is shown in green, water in blue, oil in red, while the rock is rendered transparent. (B) In a saline aquifer, CO2 is the non-wetting phase and occupies the larger pores. To restrict its flow, it must be capillary trapped through displacement with water19. (C) In an oilfield under immiscible conditions, gas (CO2) is also the most non-wetting phase: to restrict its flow it must be capillary trapped by either oil (top) or water (bottom). (D) However, we normally encounter near-miscible conditions, where CO2 exists in layers surrounding the water phase, which is now most non-wetting. CO2 flow is restricted in these layers. Here, only CO2 and water are shown for clarity. The 3D pore-scale images were acquired by X-ray micro-tomography with a voxel size of approximately 2 µm, and visualized using Avizo 9.5 software (

In CO2-EOR projects, the injection of CO2 into depleted oil and gas reservoirs can result in an additional hydrocarbon recovery, which may offset some of the cost of CO2 capture and storage15,16,17. While depleted oil and gas reservoirs are well known for their commercial quality permitting investment into large-scale EOR-CCS projects, they typically contain abandoned boreholes, which can potentially be conduits for rapid escape of stored CO2.

How should CO2 injection be designed to maximize storage security? While CO2 underground migrates over several kilometres, the physical processes that control its movement occur at the micron-scale of the pores within the rock18. In saline aquifers, subsequent to the injection of CO2, water imbibes back into the pore space either at the trailing edge of a rising CO2 plume or through engineered water injection. Since water wets the rock surfaces in saline aquifers, water flows through wetting layers, leaving CO2, the non-wetting phase, stranded in the centres of the larger pores in disconnected blobs, see Fig. 1B; hence a significant amount of CO2 can become trapped in the subsurface19,20. This capillary, or residual, trapping is important, as otherwise CO2 remains connected through these wider pores, facilitating flow and potential escape. Capillary trapping limits the movement of CO2 and is the most rapid and effective mechanism to ensure safe storage for regionally extensive saline aquifers21.

In oilfields, CO2 is often injected at conditions designed to be nearly, but not completely, miscible with the oil, to improve oil recovery22,23,24,25,26. In this case, it is conventionally assumed that CO2 is the most non-wetting phase and flows rapidly, preferentially filling the larger pore spaces, while oil and water occupy the smaller pores18,27,28. Similar to aquifers, it is believed that CO2 movement can be prevented through capillary trapping by both oil and water regardless of the rock wettability28,29,30, see Fig. 1C. To maximize both oil recovery and CO2 storage, it is considered that CO2 and water should be injected together to restrict the flow of CO2 to oil production wells31,32.

To better characterize the mechanism of CO2 storage in oilfields, we use X-ray imaging to visualize the pore structure and fluids at micron resolution inside the rock in three dimensions33. We investigate the pore-scale distribution of CO2, oil and water at conditions representative of oilfields. The pore-scale configuration of fluids determines the flow of CO2.

In this work, we challenge the assumption that CO2 remains the most non-wetting phase in oilfields, where crude oil has rendered rock surfaces oil-wet34,35. Oil and CO2, at the high pressures and temperatures encountered underground, are typically near miscible with a low interfacial tension of approximately 1 mN/m27: oil and CO2 have similar wetting properties and pore-scale configuration36. The wettability order is different such that CO2 is no longer the most non-wetting phase, instead it spreads in layers as the intermediate-wet phase, see Fig. 1D, with significant implications for trapping, flow and storage. The existence of CO2 in layers substantially impedes its movement in the reservoir, and its possible escape through boreholes, which eliminates the need for water injection to restrict its flow, and hence more of the pore space can be occupied by CO2, boosting storage capacity.

In this paper we propose a different pore-scale storage mechanism to that in saline aquifers. In aquifers, where the CO2 is non-wetting, it can be safely trapped as bubbles or ganglia in the larger pores. In oilfields, however, this trapping does not occur, as the CO2 is not the most non-wetting phase. Instead, we have a different way to restrict CO2 movement, by confining the CO2 to layers in the pore space, which means that the CO2 can only flow very slowly.

Results and Discussion

We used X-ray micro-tomography (micro-CT) to image CO2, oil and water in the pore space of a reservoir rock under oil-wet near-miscible conditions at high temperature, 70 °C, and pressure, 10.85 MPa. The rock sample was extracted from a giant producing carbonate oil reservoir in the middle east and restored to the initial reservoir wetting conditions by dynamically and statically saturating the sample using crude oil in a process called ageing. More details are provided in the Supplementary Material. Similar samples have been used previously to study water flood recovery37,38. We selected a water-alternating-gas (WAG) flooding scheme to mimic the typical displacement sequence encountered in oil reservoirs. The injection sequence into the oil saturated rock was: (i) first water flooding [WF1]; (ii) gas injection [GI], and (iii) second water flooding [WF2]. We will demonstrate where and how readily CO2 flows in the rock pore space by: (i) quantifying the configuration of the three phases; (ii) calculating the flow conductance of the phases; and (iii) measuring the amount of CO2 trapping.

Distribution of CO2, oil and water in the pore space

To understand flow and displacement we first quantify pore occupancy, see Fig. 2. The size of pores each fluid occupies controls how readily it flows in the pore space: if a fluid fills larger pores it flows more readily as opposed to filling smaller pores. We performed a topological analysis of the pore space to identify the widest regions (pores) that are connected by narrower restrictions: the pore size is the diameter of the largest sphere that fits in a pore; the centre of the sphere is the centre of the pore. The phase occupancy is defined as the phase which resides at the centre of the pore29,36,39. We find that water is the most non-wetting phase since it occupies the largest pores, followed by gas, with oil most wetting in the smallest pores. This wettability order from most to least wetting – oil, gas, water – has been seen in micro-model experiments40 but not inside reservoir rocks before, and contradicts previous studies where the oil and gas properties were not representative of subsurface CO2 storage conditions28,29.

Figure 2
figure 2

Bar charts showing the fraction of the pores occupied by each phase as a function of pore diameter after each injection step. Pore occupancy is defined as the phase in the centre of the pore – this phase will also have the largest volume in the pore. (A) Initial reservoir conditions (there is an initial water saturation of ~1% which is not evident from the bar chart) [IC], (B) first water flooding [WF1], (C) gas injection [GI], and (D) second water flooding [WF2]. Oil is shown in red, water in blue and gas, CO2, in green.

Initially, the rock was saturated with oil to restore the initial reservoir conditions, see Fig. 2A: at initial conditions (IC) some water was present in the pore space but at a very low saturation ~ 1%, which is why it is not evident on the bar chart. As expected for oil-wet media, during the first water flooding (WF1), water, the non-wetting phase, invaded the largest pores, while oil, the wetting phase, remained confined in the smaller ones. After gas injection (GI), water was trapped in the centres of the pore space as disconnected ganglia, Fig. 1D. In water-occupied pores, the gas can reside in layers next to the solid trapping water in the centre, see Fig. 5. The wettability order – oil, gas, water – is more apparent during the second water flooding (WF2), where water invaded the centres of the larger pores confining gas and oil to intermediate and small sized pores respectively. This shows that the injection of water in WF2 limits the available storage capacity for CO2 as the usable volume of the oilfield pore space occupied by CO2 is restricted.

CO2 flow conductivity

Figure 3 shows the connectivity of the phases after each injection step. During water injection, water can form a connected path through the larger pores. In contrast, oil and gas tend to form thinner structures. Oil fills the smaller pores and is retained close to the solid surface, while CO2 forms layers which follow a tortuous path through the pore space.

Figure 3
figure 3

Three-dimensional maps showing the connectivity of the phases during the displacement sequence. The colours indicate discrete clusters of each phase. The relative permeability, kr, is shown in the boxes. The oil, gas and water phase distributions were obtained by imaging at a high-resolution, 1.82 µm/voxel, the rock pore space during the experiment, while the relative permeability values were computed from flow field simulations. The connectivity maps were plotted using Avizo 9.5 software (

We computed the flow field, that is the velocity, of oil, gas and water on the images shown in Fig. 3. The simulations were performed on the largest connected phase cluster in each of the 3D images with 1483 × 1483 × 1000 voxels, see Supplementary Fig. S4. From these flow fields, the permeability of each phase can be computed. When the pore space is completely filled with one phase the absolute permeability is 3.7 × 10−13 m2; this value is close to the directly-measured value of 2.7 × 10−13 m2 through the whole sample. The relative permeability is defined as the ratio of the permeability of a phase that partially fills the pore space to the absolute permeability18. As indicated in Fig. 3, the relative permeability of gas is only 0.037 after gas injection despite having a saturation of 33 ± 2%, see Fig. 4 – the flow conductance is reduced by a factor of almost 30, while water in the larger pores has a higher relative permeability of 0.23. The oil has the lowest relative permeability of only 0.023 since it occupies the smallest pores. This reduction in oil and gas relative permeability under near-miscible oil-wet conditions has been observed in conventional flow tests on rock samples, but not explained using the wettability order23. After WF2, the gas and oil relative permeabilities are further reduced by one order of magnitude to 0.0054 and 0.0021 respectively, implying extremely restricted flow; however, less CO2 is stored in the pore space with a saturation of only 21 ± 2%, see Fig. 4.

Figure 4
figure 4

A three-phase ternary diagram showing the end-point saturations during the flooding sequence. Saturation is defined as the volume of a phase divided by the total pore volume. At first (black point on the diagram), the rock is restored to its initial reservoir conditions (water saturation: 0.01 and oil saturation: 0.99). The coloured arrows point to the chronological order of injection events: (i) first water flooding [WF1]; (ii) gas injection [GI], and (iii) second water flooding [WF2]. The error in the saturation measurement is within ± 2%.

CO2 saturation and trapping

The remaining saturation of CO2, oil and water in the rock pore space after each injection was measured on segmented images of the whole rock. The change in fluid saturations throughout the flooding sequence is shown on the ternary diagram in Fig. 4. After the first water flooding (WF1), only 39 ± 2% of the oil was recovered. This is ascribed to water invading the centres of the pores, while oil remains connected in the corners and small pores in wetting layers, Fig. 3. This is a common characteristic of oil-wet media38,41,42. During gas injection (GI), CO2, the intermediate-wet phase, displaced some of the oil that was in the corners of the pore space leaving water stranded in the centres. This is ideal from an oil recovery standpoint: the recovery factor increased to 58 ± 2%. Almost 33 ± 2% of the pore space remained saturated by CO2 after gas injection (GI). WF2 displaced both oil and CO2. Despite a substantial increase in the oil recovery during WF2 (14 ± 2%), as seen in other WAG experiments28,40, it results in a lower CO2 saturation (21 ± 2%), i.e. a lower CO2 storage capacity after water injection: less CO2 is stored and indeed some of the injected CO2 is produced with the oil. This is also a lower CO2 saturation than is capillary trapped under water-wet conditions in similar rocks19.

Gas layer thickness

Figure 5 shows maps of the local thickness of the gas layers after gas injection (GI) and second water flooding (WF2). The average saturation was approximately constant across the sample after each injection. The thickness of these gas layers was quantified on images with 746 × 491 × 600 voxels of size 1.82 µm: the thickness is defined as the diameter of the largest sphere that fits entirely in the gas phase at each location. Note that the thickness in both cases is much smaller than a typical pore size, see Fig. 2 where the x-axis of the bar chart shows the pore size distribution of the rock sample used, indicating that the gas resides principally in layers, as opposed to occupying the centres of larger pores.

Figure 5
figure 5

Three-dimensional maps of the local thickness of gas layers computed after (left) gas injection (GI) and (right) second water flooding (WF2). The thickness maps were quantified on images of voxel size of 1.82 µm with 746 × 491 × 600 voxels. The gas layers have an average thickness of approximately 15–20 µm. The layers were visualized using Avizo 9.5 software (

It is common practice to inject alternate slugs of water and gas in oilfield operations for three reasons. Firstly, this saves money, as the gas is more expensive to collect and inject than water. Secondly, it is presumed that gas is the most non-wetting phase: injecting water helps to limit gas flow and production27. Thirdly, repeated flooding cycles lead to higher oil recovery, as we see here, Fig. 4. We have shown that for storage applications, CO2 flow is restricted even when gas alone is injected. To maximize storage capacity, the CO2 saturation should be as high as possible. This implies that an injection strategy of CO2 injection only, or with limited amounts of water, is favourable, and that CO2 is unlikely to be produced in significant quantities. Moreover, we have shown that CO2 has very low relative permeability in the reservoir, which makes it harder – but not impossible – for the stored CO2 to flow towards abandoned wells and escape through legacy boreholes. Therefore, after CO2 injection, the wells must be closed in and the CO2 should remain underground for thousands of years, since its upwards migration is prevented by caprock6, see Fig. 1.


To help meet the global requirement to reduce CO2 emissions, we have investigated CO2 storage in oilfields. We have demonstrated that it is wettability order that controls the flow of fluids in the reservoir. Our results prove that the traditional assumption that CO2 is always the most non-wetting phase is incorrect. The injection of CO2 results in near-miscible conditions, where oil is the most wetting phase, occupying the smallest pores as well as wetting layers, water is the most non-wetting phase, residing in the centres of the pores, while CO2 is the intermediate-wet phase, forming layers in the corners of the pore space. This wettability order leads to the confinement of CO2 in layers of low flow conductivity. Therefore, the injection of water is not required to constrain the gas flow. The migration of CO2 beyond the oilfield is prevented by the cap rock, which has contained the hydrocarbons for millions of years.

We suggest that near-miscible conditions in reservoir rocks are ideal for recovery and storage: the wettability order oil-gas-water is likely to be seen in any oil-wet or mixed-wet rock, which comprise the majority of carbonate reservoirs18. On the other hand, if complete miscibility is achieved, the oil and gas flow together as one phase43. While this is favourable for oil recovery, it facilitates the flow of CO2 and so is less favoured for secure storage. Our experiment has considered only one rock type and mineralogy – a heterogenous reservoir calcite – but we suggest that the same trends in local displacement efficiency will be observed in any system with this wettability order and near-miscible conditions such that gas can form spreading layers. Future work could study a wider range of rock types, including sandstones, where the wettability may be different, even for the same fluids.

An engineering assessment of CO2 storage in oilfields will also involve a quantitative analysis of large-scale flow accounting for reservoir structure, variations in permeability and well placement. However, one key input is the flow potential of the phases, controlled by pore-scale fluid configurations: we have shown that the flow of CO2 is impeded by an order of magnitude or more compared to conventional models where it is the non-wetting phase. This finding implies that CO2 can be injected alone, or with minimal amounts of water, to maximize storage capacity while still restricting the possibility of CO2 escape.


Reservoir rock, wettability restoration and fluid properties

The rock selected was a carbonate extracted from a giant producing oil reservoir in the middle east (composition: 96.5 wt% calcite): the sample was a cylinder of diameter 5.9 mm and length 24.9 mm. The rock was restored to the initial reservoir wetting conditions by a process called ageing. The rock, initially brine-saturated, was flooded continually for four weeks with crude oil (an oil from the same reservoir as the rock, surface density = 830 kg/m3) at high temperature, 80 °C, and pressure, 10 MPa. We have used reservoir brine to represent the water phase, decane to represent the oil phase and CO2 in a supercritical state to represent the gas phase in the experiment. Sodium iodide (NaI) and iododecane (C10H21I) solutions were added to the water and oil phases with concentrations of 30% and 20% respectively to obtain effective phase contrast in the micro-CT images. For a more detailed description of the rock and fluid properties and the wettability restoration process please refer to the Supplementary Information.

X-ray micro-tomography imaging and flow experiment

A ZEISS Xradia 510 Versa micro-CT scanner was used to acquire high-resolution three-dimensional images of the reservoir rock and the fluids within it. The rock was inserted in a Hassler type carbon fibre coreholder that is X-ray transparent and placed inside the micro-CT for image acquisition. The coreholder was connected to flow lines to perform the injection sequence: (i) first water flooding [WF1]; (ii) gas injection [GI]; and (iii) second water flooding [WF2]. Prior to starting the injection sequence, the crude oil in the restored sample was completely displaced and replaced by doped oil at the experimental conditions, 70 °C, and 10.85 MPa. During each injection, 1 pore volume, 0.708 mL, of fluid was injected into the sample at rate of 0.005 mL/min. Images of the whole rock sample (1652 × 1652 × 66974 voxels) were acquired after each injection with a voxel size of 3.57 µm to characterize the pore occupancy and measure fluid saturations. A scan of higher resolution (1483 × 1483 × 1758 voxels), with a voxel size of 1.82 µm, was also acquired at the centre of the rock to examine gas layers. The images were acquired 2 h after each injection to allow the fluids in the rock pore space to reach equilibrium conditions. After the experiment, the rock was cleaned to remove any organic material by injecting toluene into the pore space, followed by the injection of deionized water, and then dried at 60 °C in vacuum for three days to prepare the sample for acquisition of a dry scan. This was done after the experiment for convenience so that all the images could be acquired during the same period. A more detailed description of the flow apparatus, experimental procedure and image acquisition can be found in the Supplementary Information.

Image processing and segmentation

The raw micro-CT images acquired were processed for phase identification, i.e. image segmentation. The images were segmented into four phases: water, rock, oil and gas. The 3.57 µm voxel images of the whole sample were segmented using the seeded watershed algorithm44. A non-local means filter was applied to the 3.57 µm voxel images to smooth the grey scale images and improve the watershed segmentation45. The higher resolution images, 1.82 µm voxel size, were segmented using machine learning-based trainable WEKA segmentation method46. WEKA segmentation was chosen to segment the high-resolution images as it preserves the shape of the interface between the phases, facilitating more accurate characterization of flow properties and thicknesses of gas layers38. However, WEKA is very CPU intensive, hence, it was not possible to apply it to the large 3.57 µm voxel size images of the whole sample. A more detailed description of the image segmentation is provided in the Supplementary Information.

Flow simulation

We computed flow on segmented high-resolution images of size 2.2 × 109 voxels. We treated each phase separately and solved the Navier-Stokes equation using a finite volume method47 with a constant pressure differential across the image in the experimental direction of flow, and with no flow boundaries with the solid and the interfaces with other phases. The no-flow boundary condition removes complexities in the calculation, so that the flow of one phase is not dependent on the flow rate and direction of the other phases. This is also a good approximation for layer flow of CO2 since it is much less viscous than the oil or water (see, for instance, Shams, et al.48 for a quantification of these effects in simple geometries). The permeability of the phase was computed from the ratio of flow rate to pressure gradient using Darcy’s law. For more details refer to the Supplementary Information.


  1. Allen, M. et al. Global warming of 1.5 °C. An IPCC Special Report on the impacts of global warming of 1.5 °C above pre-industrial levels and related global greenhouse gas emission pathways, in the context of strengthening the global response to the threat of climate change, sustainable development, and efforts to eradicate poverty. IPCC Special Report, (2019).

  2. BP Statistical Review of World Energy. BP Statistical Review of World Energy, (2019).

  3. Metz, B., Davidson, O., De Coninck, H., Loos, M. & Meyer, L. Carbon dioxide capture and storage: special report of the intergovermental panel on climate change. (Cambridge University Press, 2005).

  4. Bickle, M. J. Geological carbon storage. Nature Geoscience 2, 815–818, (2009).

    ADS  CAS  Article  Google Scholar 

  5. Scott, V., Haszeldine, R. S., Tett, S. F. B. & Oschlies, A. Fossil fuels in a trillion tonne world. Nature Climate Change 5, 419,, (2015).

  6. Alcalde, J. et al. Estimating geological CO2 storage security to deliver on climate mitigation. Nature Communications 9, 2201, (2018).

    ADS  CAS  Article  PubMed  PubMed Central  Google Scholar 

  7. Bellamy, R. & Geden, O. Govern CO2 removal from the ground up. Nature Geoscience 12, 874–876, (2019).

    ADS  CAS  Article  Google Scholar 

  8. Bui, M. et al. Carbon capture and storage (CCS): the way forward. Energy & Environmental Science 11, 1062–1176 (2018).

    CAS  Article  Google Scholar 

  9. Scott, V., Gilfillan, S., Markusson, N., Chalmers, H. & Haszeldine, R. S. Last chance for carbon capture and storage. Nature Climate Change 3, 105–111, (2013).

    ADS  CAS  Article  Google Scholar 

  10. Szulczewski, M. L., MacMinn, C. W., Herzog, H. J. & Juanes, R. Lifetime of carbon capture and storage as a climate-change mitigation technology. Proceedings of the National Academy of Sciences 109, 5185, (2012).

    ADS  Article  Google Scholar 

  11. Brownsort, P. et al. CO2 storage and Enhanced Oil Recovery in the North Sea: Securing a low-carbon future for the UK. SCCS. (2015).

  12. Melzer, S. Optimization of CO2 Storage in CO2 Enhanced Oil Recovery Projects. Advanced Resources International (2010).

  13. Kramer, D. Negative carbon dioxide emissions. Physics today 73, 44–51 (2020).

    ADS  CAS  Article  Google Scholar 

  14. Bhown, A. S., Bromhal, G. & Barki, G. CO2 Capture and Sequestration. Fossil Energy, 503–517 (2020).

  15. Heidug, W., Lipponen, J., McCoy, S. & Benoit, P. Storing CO2 through Enhanced Oil Recovery: Combining EOR with CO2 storage (EOR+) for profit. Insight Series (2015).

  16. Stewart, R. J., Johnson, G., Heinemann, N., Wilkinson, M. & Haszeldine, R. S. Low carbon oil production: Enhanced oil recovery with CO2 from North Sea residual oil zones. International Journal of Greenhouse Gas Control 75, 235–242, (2018).

    CAS  Article  Google Scholar 

  17. Núñez-López, V., Gil-Egui, R. & Hosseini, S. A. Environmental and Operational Performance of CO2-EOR as a CCUS Technology: A Cranfield Example with Dynamic LCA Considerations. Energies 12, 448 (2019).

    Article  Google Scholar 

  18. Blunt, M. J. Multiphase flow in permeable media: A pore-scale perspective, (Cambridge University Press, 2017).

  19. Andrew, M., Bijeljic, B. & Blunt, M. J. Pore-scale imaging of geological carbon dioxide storage under in situ conditions. Geophysical Research Letters 40, 3915–3918, (2013).

    ADS  CAS  Article  Google Scholar 

  20. Bruant, R. G. Jr., Celia, M. A., Guswa, A. J. & Peters, C. A. Peer Reviewed: Safe Storage of CO2 in Deep Saline Aquifiers. Environmental Science & Technology 36, 240A–245A, (2002).

    ADS  CAS  Article  Google Scholar 

  21. Krevor, S. et al. Capillary trapping for geologic carbon dioxide storage – From pore scale physics to field scale implications. International Journal of Greenhouse Gas Control 40, 221–237, (2015).

    CAS  Article  Google Scholar 

  22. Shyeh-Yung, J. G. J. 1991. Mechanisms of Miscible Oil Recovery: Effects of Pressure on Miscible and Near-Miscible Displacements of Oil by Carbon Dioxide. SPE Annual Technical Conference and Exhibition. Dallas, Texas: Society of Petroleum Engineers, No. 22651.

  23. Fatemi, S. M. & Sohrabi, M. Recovery Mechanisms and Relative Permeability for Gas/Oil Systems at Near-Miscible Conditions: Effects of Immobile Water Saturation, Wettability, Hysteresis, and Permeability. Energy & Fuels 27, 2376–2389, (2013).

    CAS  Article  Google Scholar 

  24. Sohrabi, M., Danesh, A., Tehrani, D. H. & Jamiolahmady, M. Microscopic Mechanisms of Oil Recovery By Near-Miscible Gas Injection. Transport in Porous Media 72, 351–367, (2008).

    CAS  Article  Google Scholar 

  25. Wylie, P. & Mohanty, K. K. Effect of Water Saturation on Oil Recovery by Near-Miscible Gas Injection. SPE-25254-PA 12, 264–268, (1997).

    CAS  Article  Google Scholar 

  26. Thomas, F. B., Holowach, N. & Zhou, X. Miscible or Near-Miscible Gas Injection, Which Is Better? Proceedings of the SPE/DOE Improved Oil Recovery Symposium. Tulsa, Oklahoma, No. 55563 (1994).

  27. Lake, L. W. Enhanced oil recovery. Elsevier (1989).

  28. Qin, Z., Arshadi, M. & Piri, M. Micro-scale experimental investigations of multiphase flow in oil-wet carbonates. II. Tertiary gas injection and WAG. Fuel 257, 116012, (2019).

    CAS  Article  Google Scholar 

  29. Scanziani, A., Singh, K., Bultreys, T., Bijeljic, B. & Blunt, M. J. In situ characterization of immiscible three-phase flow at the pore scale for a water-wet carbonate rock. Advances in Water Resources 121, 446–455, (2018).

    ADS  Article  Google Scholar 

  30. Scanziani, A., Alhammadi, A., Bijeljic, B. & Blunt, M. J. In Abu Dhabi International Petroleum Exhibition & Conference 8 (Society of Petroleum Engineers, Abu Dhabi, UAE, 2018).

  31. Qi, R., LaForce, T. C. & Blunt, M. J. Design of carbon dioxide storage in aquifers. International Journal of Greenhouse Gas Control 3, 195–205, (2009).

    CAS  Article  Google Scholar 

  32. Qi, R., Beraldo, V. T., LaForce, T. C. & Blunt, M. J. Design of Carbon Dioxide Storage in a North Sea Aquifer Using Streamline-Based Simulation. SPE Annual Technical Conference and Exhibition. Anaheim, California, U.S.A, No. 22561, 10.2118/109905-MS(2007).

  33. Wildenschild, D. & Sheppard, A. P. X-ray imaging and analysis techniques for quantifying pore-scale structure and processes in subsurface porous medium systems. Advances in Water Resources 51, 217–246, (2013).

    ADS  Article  Google Scholar 

  34. Buckley, J. S. Effective wettability of minerals exposed to crude oil. Current Opinion in Colloid & Interface Science 6, 191–196, (2001).

    CAS  Article  Google Scholar 

  35. AlRatrout, A., Blunt, M. J. & Bijeljic, B. Wettability in complex porous materials, the mixed-wet state, and its relationship to surface roughness. Proceedings of the National Academy of Sciences 115, 8901, (2018).

    ADS  CAS  Article  Google Scholar 

  36. Alhosani, A. et al. In situ pore-scale analysis of oil recovery during three-phase near-miscible CO2 injection in a water-wet carbonate rock. Advances in Water Resources 134, 103432, (2019).

    CAS  Article  Google Scholar 

  37. Alhammadi, A. M., AlRatrout, A., Bijeljic, B. & Blunt, M. J. Pore-scale Imaging and Characterization of Hydrocarbon Reservoir Rock Wettability at Subsurface Conditions Using X-ray Microtomography. JoVE, e57915, (2018).

  38. Alhammadi, A. M., AlRatrout, A., Singh, K., Bijeljic, B. & Blunt, M. J. In situ characterization of mixed-wettability in a reservoir rock at subsurface conditions. Scientific Reports 7, 10753, (2017).

    ADS  CAS  Article  PubMed  PubMed Central  Google Scholar 

  39. Scanziani, A., Singh, K., Menke, H., Bijeljic, B. & Blunt, M. J. Dynamics of enhanced gas trapping applied to CO2 storage in the presence of oil using synchrotron X-ray micro tomography. Applied Energy, 114136, (2019).

  40. van Dijke, M. I. J., Sorbie, K. S., Sohrabi, M. & Danesh, A. Simulation of WAG floods in an oil-wet micromodel using a 2-D pore-scale network model. Journal of Petroleum Science and Engineering 52, 71–86, (2006).

    CAS  Article  Google Scholar 

  41. Singh, K., Bijeljic, B. & Blunt, M. J. Imaging of oil layers, curvature and contact angle in a mixed-wet and a water-wet carbonate rock. Water Resources Research 52, 1716–1728, (2016).

    ADS  Article  Google Scholar 

  42. Iglauer, S., Fernø, M. A., Shearing, P. & Blunt, M. J. Comparison of residual oil cluster size distribution, morphology and saturation in oil-wet and water-wet sandstone. Journal of Colloid and Interface Science 375, 187–192, (2012).

    ADS  CAS  Article  PubMed  Google Scholar 

  43. Teletzke, G. F., Patel, P. D. & Chen, A. 2005. 2007. Methodology for Miscible Gas Injection EOR Screening. SPE International Improved Oil Recvery Conderence in Asia. Kuala Lumpur, Malaysia, No. 97650,

  44. Brown, K., SchlÜTer, S., Sheppard, A. & Wildenschild, D. On the challenges of measuring interfacial characteristics of three-phase fluid flow with x-ray microtomography. Journal of Microscopy 253, 171–182, (2014).

    CAS  Article  PubMed  Google Scholar 

  45. Buades, A., Coll, B. & Morel, J.-M. Nonlocal Image and Movie Denoising. International Journal of Computer Vision 76, 123–139, (2008).

    Article  Google Scholar 

  46. Arganda-Carreras, I. et al. Trainable Weka Segmentation: a machine learning tool for microscopy pixel classification. Bioinformatics 33, 2424–2426, (2017).

    CAS  Article  PubMed  Google Scholar 

  47. Raeini, A. Q., Blunt, M. J. & Bijeljic, B. Modelling two-phase flow in porous media at the pore scale using the volume-of-fluid method. Journal of Computational Physics 231, 5653–5668, (2012).

    ADS  MathSciNet  Article  Google Scholar 

  48. Shams, M., Raeini, A. Q., Blunt, M. J. & Bijeljic, B. A study to investigate viscous coupling effects on the hydraulic conductance of fluid layers in two phase flow at the pore level. Journal of Colliod and interface science 522, 299–310, (2018).

    ADS  CAS  Article  MATH  Google Scholar 

Download references


We acknowledge Abu Dhabi National Oil Company (ADNOC) for financially supporting this research.

Author information

Authors and Affiliations



A.A. led the experimental work alongside A.S. and Q.L. under the supervision of M.J.B. and B.B. A.Q.R. performed the flow simulations. A.A., A.S., Q.L., A.Q.R., B.B. and M.J.B. were involved in the design of the study, acquiring and analysing data, and writing the manuscript.

Corresponding author

Correspondence to Abdulla Alhosani.

Ethics declarations

Competing interests

The authors declare no competing interests.

Additional information

Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Supplementary information

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Alhosani, A., Scanziani, A., Lin, Q. et al. Pore-scale mechanisms of CO2 storage in oilfields. Sci Rep 10, 8534 (2020).

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI:

Further reading


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.


Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing