Abstract
Customized cosmetics made by consumers or sellers on-the-spot have several safety issues, and therefore require a preventative approach to their safety management. The present study aimed to identify potential factors affecting the safety of customized cosmetics made on-the-spot. Heavy metals and microbial contaminants in customized cosmetics were analyzed in 120 samples. It was revealed that the transfer of cosmetics to new containers during the production process is a significant risk factor for cross-contamination and that heat treatment is crucial for reducing the number of microorganisms in the products. For instance, cosmetics made with heat and with no transfer showed relatively low microbial counts ranging from not detected to 440 CFU/ml. The high pH (>pH 10) of samples did not guarantee the microbial safety of the freshly made cosmetics (with a rinse-off product having 2,830 CFU/ml and a pH of 11.2). There was no significant difference in microbial counts among cosmetic types (Pā>ā0.05); however, semisolid types, especially creams and rinse-off products, were susceptible to contamination (maximum 2,710 and 2,830 CFU/ml, respectively). Most microorganisms in the customized cosmetics (40.8%) decreased to non-detectable levels during 60 days of storage. None of the samples harbored heavy metals. Sequencing analysis of isolates revealed some bacteria and mold that could cause human infections. The results of this study suggest that the regulation of customized cosmetics should consider the risk factors revealed in this study, as the products made on-the-spot are also final products sent directly to consumers.
Similar content being viewed by others
Introduction
South Korea, the 8th largest cosmetic market in the world1, is at the forefront of the customized cosmetic trends. In 2016, the South Korean government conducted a pilot project on customized cosmetics targeting products made on-the-spot by readily producing bases and ingredients for colors, scents, and functionalities according to the consumerās preference2. Customized cosmetics, such as consumer-fit skincare products, makeup products, and perfume, have already been sold in Europe, the USA, Canada, Australia, etc3,4,5,6. This pilot project was the worldās first governmental activity for the assessment and development of customized cosmetics made on-the-spot by consumers or sellers in the market.
Cosmetics are important vehicles of transmission of pathogens in peopleās daily lives7. Most cosmetics, including customized cosmetics, contain an abundant amount of water and nutrients8, thereby providing good substrates for the survival of a variety of microorganisms9. The microbial contamination of cosmetics and the survival of microorganisms deteriorate the quality of the cosmetic and seriously affect human health8,10,11. Although safety issues resulting from contaminated cosmetics are currently rare12, product recalls still occur worldwide due to microbial contamination of the products13,14.
Cosmetics are not required to be sterile; however, the safety of the products after they have been sold to consumers also has to be assured15. To combat bacterial contamination and growth in cosmetics, the microbiological stability and durability of commercial cosmetics are tested before launch. However, the preservation system of customized cosmetics made-on-the spot cannot be assured as they are made on site and sent directly to consumers. The production process of on-the-spot cosmetics is also complicated (Fig.Ā S1) and includes potential risks for cross-contamination from the surrounding environment, utensils, or handlers. Accordingly, these cosmetics can be susceptible to microbial contamination during the production process. Thus, microbial contamination of these novel cosmetics and their regulation is a concern for the public, manufacturers, and the government.
As customized cosmetics made on-the-spot are regarded as general commercial cosmetics, final products should comply with microbial quality and heavy metal limits. Although there are currently no internationally harmonized limits, it is generally accepted that total aerobic microbe counts of cosmetics for children under the age of three should be below 100 CFU/g or ml; those of the other cosmetic products should be below 1,000 CFU/g or ml in Europe, the USA, and South Korea16,17. The absence of E. coli, P. aeruginosa, and S. aureus, which are described as specified microorganisms that are generally considered undesirable in cosmetic products, is required in cosmetics18. Heavy metals (lead, arsenic, mercury, antimony, and cadmium) should also be managed according to the regulations18.
In the present study, to provide a comprehensive understanding of the potential microbial and chemical risks of customized cosmetics made on-the-spot, all shops participating in the national pilot project on customized cosmetics available in South Korea were investigated. Multifaceted approaches were applied to identify potential factors affecting the safety of customized cosmetics made on-the-spot, including preparation methods, pH, cosmetic types, forms, and storage (stability test) of the products. Heavy metals and microbial prevalence in the total of 120 customized cosmetic samples were also analyzed to evaluate the current safety of the products.
Results and Discussion
The US FDA states that cosmetics need not be sterile; however, cosmetic products must not be contaminated with pathogenic microorganisms, and the level of nonpathogenic microorganisms should be low12. Achieving this standard requires a good quality management system for cosmetics, which consists of raw material quality and hygienic design of facilities19. Accordingly, good manufacturing practice (GMP) has been implemented over the decades to improve the industrial quality control of cosmetics11. However, GMP regulations are not appropriate for customized cosmetics made on-the-spot because this type of cosmetics can be made by untrained customers or sellers in shops with no specialized facilities for the manufacture of cosmetics. Customized cosmetics, therefore, are at risk of microbial contamination during the production process. The current study targeted all customized cosmetics made on-the-spot by the national pilot project in South Korea. Because the number of customized cosmetic products can be innumerable according to the mixed ingredients, the plan for sample collection was designed with the following criteria based on a previous field survey: i) to include a formula that is recommended by seller, ii) to include well-known customized cosmetic formulas (the most frequently sold products), iii) to include all raw materials used in the shops, and iv) to include the maximum number of raw materials that can be combined in the final products. Finally, a total of 120 customized cosmetic samples consisting of nine types, and three forms were collected directly from shops and analyzed.
The microbiological prevalence of freshly made cosmetic samples was clear (Fig.Ā 1). Aerobic microbes were detected in a total of 49 samples (40.8%), and the microbial counts of the positive samples ranged from 10ā2,830 CFU/g or ml. According to the microbial limit specified in the national regulations18, the total aerobic microbe counts of cosmetics for children under the age of three should be below 100 CFU/g or ml; those of other cosmetic products should be below 1,000 CFU/g or ml. This limit is considered high enough to prevent rejection of most contaminated cosmetic products. In this study, three customized cosmetics (a rinse-off product, baby lotion, and moisturizer) did not comply with the standard limit (2,830 CFU/ml, 530 CFU/ml, and 2,710 CFU/ml, respectively) (Table S2).
The results of this study are similar to those of many other studies on commercial cosmetics, which reported microbial counts in creams, lotions, bath foam, and shampoo ranging from 102 to 104 CFU/g or ml8,11,13,20,21. Although there was no significant difference in the microbial counts of customized cosmetics according to cosmetic types (Pā>ā0.05) (Figs.Ā 1 and 2), creams that are generally recognized as being susceptible to microbial contamination also showed high aerobic microbe counts (Fig.Ā S2), and therefore require proper quality control during preparation at the shop.
The most specific characteristic of customized cosmetics is the preparation process at the shop. Unlike cosmetic manufacturing plants, customized cosmetic shops use small-scale equipment for heating and mixing ingredients or manual mixing of the ingredients with rods or by shaking; mixed products are sometimes transferred to new cosmetic containers using a spatula or not (Fig.Ā S1). In this study, customized cosmetics (rinse-off products) made with heating (M1) and without transfer (M4 and M5) showed relatively low microbial counts (ND to 440 CFU/ml) (Fig.Ā 3). However, cosmetics made with no heating and that were transferred to new containers (M2 and M3) showed increased microbial counts (ND to 2,830 CFU/ml). These results clearly indicate that heating is a crucial factor for reducing microorganisms in customized cosmetics and that the transfer of cosmetics to new containers could result in cross-contamination.
It was also well known that cosmetic products with pH values below 3 or above 10 are considered to have a low risk of microbial growth22; however, it was shown that customized cosmetics with pH values above 10 contained microorganisms in this study (Figs.Ā 4 and S3). As customized cosmetics are made on-the-spot, the high pH condition may have not greatly affected the survival of the contaminated microorganisms. However, the freshly made cosmetics are also final products; thus, the improved hygienic control of customized cosmetics, even high-pH cosmetics, should be considered.
Several studies have shown that the most frequently found microorganisms in cosmetics are P. aeruginosa, S. aureus, E. coli, and Bacillus species, as well as other bacteria, mold and yeasts8,9,10,23,24. In this study, we used traditional testing methods for specified microorganisms by using enrichment and selective medium; however, no target bacteria were isolated. Instead, we isolated and identified certain microorganisms, which cannot be isolated by the traditional testing methods, in customized cosmetics by 16S rRNA and ITS sequencing (Fig.Ā 5). Most isolates of the study were identified as safe microorganisms that are observed on normal skin or are ubiquitous in nature, such as soil, water, and air. However, some bacteria and molds that cause human infections were also observed, such as S. epidermidis, B. cereus, B. circulans, and A. versicolor.
Some species of Staphylococcus, such as S. epidermidis, could cause skin infections such as desquamate and acne25. Bacillus, the second most prominent genus, are transient skin microflora26, and B. cereus contamination in eye cosmetics could also cause severe eye infections25. Fungal multiplication in cosmetics is more rapid and evident than bacteria, and fungal infections can be caused by Candida, Aspergillus, and Penicillium species in particular7,23. Most isolated fungi in this study were not pathogenic, generally being those found in food and the environment, and used as cosmetic ingredients in some cases (e.g., Trametes versicolor); however, some are not good for human health. For instance, A. versicolor is an eye, nose, and throat irritant as are other Aspergillus species.
The microbial contaminants of customized cosmetics can originate from i) contaminated raw materials, ii) the specific production process of customized cosmetics, iii) the sanitary conditions of the environment and equipment (i.e., improper air conditioning of the shop, reuse of utensils, etc.) and iv) poor personal hygiene. Though microbial populations in some raw materials, air, hand, and utensil samples were quite low in the limited study (Tables S3 and S4), phylogenetic tree showed that same bacterial species were isolated from different sources (Fig.Ā S4). For example, Bacillus species were observed in raw materials and final products. Therefore, the risk factors mentioned above should be monitored continuously and be managed by a regulation for the preparation and sale of customized on-the-spot cosmetics.
It is also important to identify the microbiological stability and durability of these contaminated customized cosmetics through the storage period to determine their potential risk during consumer use. Here, the survival of bacteria and yeast and mold in 49 customized cosmetics was tested for up to 60 days (Fig.Ā 6). Because most aerobic microbes decreased to the ND level or the residual microbial counts were reduced, the preservative system of customized cosmetics is considered safe. However, as the preservative effect of customized cosmetics cannot be verified before consumer use, sellers could test possible combinations of customized cosmetics in advance, could display the information of customized cosmetics (i.e., ingredients used, lot number of raw materials, mixing ratios, etc.), or could store and test the remains of cosmetic samples sold.
According to our previous consumer survey, one of the major safety issues of customized cosmetics is chemical reactions when mixing the ingredients at the shops5. However, experts in an advisory committee for cosmetics pointed out heavy metals in the final cosmetic samples are more important than chemical reactions because most ingredients used for customized cosmetics are safe materials that can be mixed with various other ingredients. In this study, five types of heavy metals, lead, arsenic, mercury, antimony, and cadmium, were tested in 120 customized cosmetic samples, and none of the samples harbored heavy metals.
Conclusions
In conclusion, while the sanitary conditions of the environment, utensils, and handlers of the customized cosmetic shops were determined to be of good status by a preliminary survey, high microbial counts and the presence of microorganisms in the final products still indicates possible microbial contamination during the production of customized cosmetics. The results of this study clearly identified risk factors for cosmetic contamination; semisolid type products, including cream and rinse-off products, are the most susceptible to microbial contamination; pH values of cosmetics greater than 10 did not guarantee low microbial counts in the case of freshly made customized cosmetics; the major risk factors for microbial contamination of customized cosmetics made on-the-spot are thought to be raw materials and the transfer of cosmetics to new containers; and heat treatment during the process is a critical control point that could affect the microbiological levels of customized cosmetics. The empirical results provided herein may help authorities establish legislation and regulations for customized cosmetics and help cosmetic manufacturers and sellers to design strategic management plans to improve the quality and safety of customized on-the-spot cosmetics. Indeed, South Korea government announced that regulations for the customized cosmetics made on-the-spot would be enforced in 2020.
Methods
Sample collection
A total of 120 commercially available customized cosmetics, processed in the shops by consumers or sellers just before sale, were collected from March to September 2016 in Seoul, South Korea. The composition of nine different cosmetic types and the number of customized cosmetics are presented in Table S1. Briefly, perfume (nā=ā10), skin or mist (nā=ā12), lotion (nā=ā12, including lotion for babies), essence (nā=ā10), cream (nā=ā24), oil (nā=ā3), lip products (nā=ā16), rinse-off products (nā=ā28; cleansing oil, foam cleanser, hand cleanser, shampoo, conditioner, and body cleanser) and other products (nā=ā5; clay mask, mask pack, and peels and scrubs) were collected and subjected to microbiological and chemical analyses immediately after delivery to the laboratory (within 1āhour).
Microbiological testing of customized cosmetics
All microbiological analyses were performed according to the US Food and Drug Administration Bacteriological Analytical Manual: Microbiological Methods for Cosmetics17 and the Koreas regulations on safety standards, etc. of cosmetics18, with some modifications.
Microbial counts: bacteria and yeast/mold
For water-miscible products, 1āml or g of the well-mixed sample was transferred to a dilution tube containing 9āml of modified Letheen broth (MLB, Difco, Sparks, MD, USA). For water-immiscible products, 1āml or g of the sample was transferred to a dilution tube containing 8āml of MLB and 1āml of polysorbate 80 and then homogenized. If the sample was not well dispersed, glass beads were added and placed in a water bath at 40āĀ°C for 20āmin and vortexed. Homogenized samples were serially diluted using 10-fold dilution methods with 9āml of 0.85% sterile saline. One hundred microliters of diluent was spread-plated on modified Letheen agar (MLA, Difco) and potato dextrose agar (PDA, Difco) in duplicate. To reduce the detection limit to 10 CFU/ml or g, 1āml of the sample was spread plated onto three plates. MLA and PDA were incubated at 35āĀ°C for 24āhours and at 20āĀ°C for 5 days, respectively. The number of colonies on the plates was then counted and calculated as CFU/ml or g. The number of aerobic microorganisms was calculated based on the total number of bacteria and fungi.
Presence of specified microorganisms: Escherichia coli, Pseudomonas aeruginosa, and Staphylococcus aureus
To examine the specified microorganisms in the customized cosmetics, 1āml or g of the well-mixed sample was transferred to a dilution tube containing 9āml of lactose broth (Difco) for E. coli or tryptic soy broth (TSB, Difco) for P. aeruginosa and S. aureus. For water-immiscible products, 8āml of broth and 1āml of Polysorbate 80 were used as described above. The mixture was homogenized and incubated at 37āĀ°C for 24āhours. Next, one loopful of enriched culture was streaked onto selective agar plates and incubated for presumptive identification of specified microorganisms as follows: E. coli (eosin methylene blue agar, Difco), P. aeruginosa (cetrimide agar, Difco), and S. aureus (Baird-Parker agar, Difco) at 37āĀ°C for 24āhours. Typical colonies were isolated and confirmed by VITEK2 (bioMerieux) with GN (E. coli), ANC (P. aeruginosa), and GP (S. aureus) cards.
Genomic DNA isolation, sequencing, and phylogenetic analysis
Isolates from the quantitative microbiological analysis of customized cosmetics were Gram stained to confirm the bacterial type. Briefly, a smear made from an emulsified colony was air dried and heat fixed. It was covered with crystal violet for 60āsec and washed off. The smear was then covered with lugolās iodine for 60āsec, washed off, and decolorized with acetone alcohol for 15āsec. It was washed off again and counter stained with safranin for 60āsec. After washing, the smear was examined using microscopy (Leica DM6000, Leica Microsystems GmbH, Mannheim, Germany). Genomic DNA was then extracted using a LaboPass mini kit (Cosmogenetech, Seoul, South Korea) according to the manufacturerās instructions. The 16S rRNA gene of bacteria and the internal transcribed spacer (ITS) region of fungi was amplified by PCR with the universal primers 27āF (5ā²-AGAGTTTGATCCTGGCTCAG-3ā²) and 1492āR (5ā²-GGTTACCTTGTTACGACTT-3ā²) for bacteria27 and ITS1 (5ā²-TCCGTAGGTGAACCTGCGG) and ITS4 (5ā²-TCCTCCGCTTAT TGATATGC) for fungi28. Cloned PCR amplicons were purified using a MEGAquick-spin Total Fragment DNA Purification kit (iNtRON Biotechnology, South Korea) and then sequenced by the Cosmogenetech Sequencing Service (Cosmogenetech). Briefly, sequencing reactions were performed using BigDye terminator PCR with the following conditions: predenaturation at 94āĀ°C for 1āmin, 25 cycles of denaturation at 94āĀ°C for 20āsec, annealing at 50āĀ°C for 15āsec, and extension at 60āĀ°C for 4āmin. The gene sequence was then analyzed with BLAST sequence analysis software (https://blast.ncbi.nlm.nih.gov/Blast.cgi) using the National Center for Biotechnology Information (NCBI) server.
pH measurement
Customized cosmetic products for pH measurement were prepared by adding 2āml or g of the sample to 30āml of distilled water, that is to say we measured the pH of the diluted sample. The diluents were heated in a water bath at 40āĀ°C to dissolve and mix the fat. The pH of the samples was measured using an S20 SevenEasy pH meter (Mettler Toledo, Schwerzenbach, Switzerland) at room temperature. The pH meter was calibrated sequentially before measurement with commercially available three-point standard buffer solutions at pH 4.01, 7.00, and 10.01 (Mettler Toledo).
Determination of lead, arsenic, mercury, antimony, and cadmium
Heavy metals in customized cosmetic products were analyzed by an authorized laboratory for cosmetic inspection in South Korea (Korea Advanced Food Research Institute). Briefly, lead (Pb) and arsenic (As) were determined using inductively coupled plasma ā optical emission spectrometry (ICP-OES Optima 8300DV, Perkin Elmer, USA), mercury (Hg) was measured by a direct thermal decomposition mercury analyzer (NIC MA-3000, Nippon Instrument Corporation, Japan), and antimony (Sb) and cadmium (Cd) were analyzed by ICP-MS (icapQ, Thermo Science, USA).
Statistical analysis
Microbial counts of samples tested in this study were statistically analyzed using SAS software version 9.4 (Statistical Analysis Systems Institute, Cary, NC, USA; https://www.sas.com/en_us/software/sas9.html). Data were examined using a general linear model for analysis of variance, and Tukeyās test was used to determine the significance of differences (Pā<ā0.05).
Change history
30 April 2020
An amendment to this paper has been published and can be accessed via a link at the top of the paper.
References
International Trade Administration, Korea Country Commercial Guide-Cosmetics (available at, https://www.export.gov/article?id=Korea-Cosmetics), (2017).
Linaja, K.L., New trend: Korean customized cosmetics gains popularity (available at, http://en.koreaportal.com/articles/22227/20160907/new-trend-korean-customized-cosmetics-gains-popularity.htm) (2016).
Lombardi, J. & Morante, N., Method and system for color customizing cosmetic mass products, US Patent No. 6,177,093 (2001).
OāBrien, M. Customizing cosmetics: Why personalization is especially important in the beauty industry (available at, https://www.sailthru.com/marketing-blog/personalization-beauty-industry/) (2018).
Rhee, M.S. et al, Improvement plan of customized cosmetics management system, Government report from Ministry of Food and Drug Safety in Korea 15162MFDS053 (2016).
R. Raphael, Is customization the future of the beauty industry? (available at, https://www.fastcompany.com/3064239/is-customization-the-future-of-the-beauty-industry) (2016).
Babalola, M. O. & Eze, M. Microbiological Quality and Characterization of Potential Pathogens Associated with Selected Brands of Commercial Cosmetic Products in Nigeria. Br. Microbiol. Res. J. 9(5), 1ā17 (2015).
Shaqra, Q. M. A. & Al-Groom, R. M. Microbiological quality of hair and skin care cosmetics manufactured in Jordan. Int. Biodeterior. Biodegrad. 69, 69ā72 (2012).
Neza, E. & Centini, M. Microbiologically contaminated and over-preserved cosmetic products according Rapex 2008ā2014. Cosmetics 3(1), 3 (2016).
Behravan, J., Bazzaz, F. & Malaekeh, P. Survey of bacteriological contamination of cosmetic creams in Iran (2000). Int. J. Dermatol. 44(6), 482ā485 (2005).
Campana, R., Scesa, C., Patrone, V., Vittoria, E. & Baffone, W. Microbiological study of cosmetic products during their use by consumers: health risk and efficacy of preservative systems. Lett. Appl. Microbiol. 43(3), 301ā306 (2006).
Stewart, S., Parker, M., AmĆ©zquita, A. & Pitt, T. Microbiological risk assessment for personal care products. Int. J. Cosmetic Sci. 38(6), 634ā645 (2016).
Okeke, I. N. & Lamikanra, A. Bacteriological quality of skināmoisturizing creams and lotions distributed in a tropical developing country. J. Appl. Microbiol. 91(5), 922ā928 (2001).
SGS, Importance of microbiological quality to cosmetics (available at, https://www.sgsgroup.com.hk/en/news/2017/02/importance-of-microbiological-quality-to-cosmetics) (2017).
Budecka, A. & Kunicka-StyczyÅska, A. Microbiological contaminants in cosmeticsāisolation and characterization, (available at, http://www.bfs.p.lodz.pl) (2014).
SCCS, E., The SCCSās Notes of Guidance for the Testing of Cosmetic Ingredients and Their Safety Evaluation 8th Revision (2012).
US FDA (Food and Drug Administration), BAM: Microbiological methods for cosmetics - Chapter 23 (available at, https://www.fda.gov/food/foodscienceresearch/laboratorymethods/ucm565586.htm) (2001).
Ministry of Food and Drug Safety, Regulations on the Safety Standards, etc. of Cosmetics (available at, https://chemicalwatch.com/asiahub/54695/regulation-on-safety-standards-etc-of-cosmetics) (2017).
Siegert, W. Microbiological quality management for the production of cosmetics and detergents. SOFW Journal. 138(11), 30 (2012).
Hugbo, P. G., Onyekweli, A. O. & Igwe, I. Microbial contamination and preservative capacity of some brands of cosmetic creams. Trop. J. Pharm. Res. 2(2), 229ā234 (2003).
Muhammed, H. J. Bacterial and fungal contamination in three brands of cosmetic marketed in Iraq. Iraqi J. Pharm. Sci. 20(1), 38ā42 (2017).
Fellenberg, B. Microbiological quality of cosmetics - Legal requirements, test methods and risk assessment. Euro Cosmetics 36, 36ā39 (2016).
Lundov, M. D., Moesby, L., Zachariae, C. & Johansen, J. D. Contamination versus preservation of cosmetics: a review on legislation, usage, infections, and contact allergy. Contact Dermatitis. 60(2), 70ā78 (2009).
Anelich, L. & Korsten, L. Survey of microāorganisms associated with spoilage of cosmetic creams manufactured in South Africa. Int. J. Cosmet. Sci. 18(1), 25ā40 (1996).
AYRES, S. JR, R. MIHAN, Acne vulgaris and lipid peroxidation: new concepts in pathogenesis and treatment. Int. J. Dermatol. 17(4), 305ā307 (1978).
Dadashi, L. & Dehghanzadeh, R. Investigating incidence of bacterial and fungal contamination in shared cosmetic kits available in the women beauty salons. Health Promot. Perspect. 6(3), 159 (2016).
Amann, R. I., Ludwig, W. & Schleifer, K.-H. Phylogenetic identification and in situ detection of individual microbial cells without cultivation. Microbiol. Rev. 59(1), 143ā169 (1995).
White, T. J., Bruns, T., Lee, S. & Taylor, J. Amplification and direct sequencing of fungal ribosomal RNA genes for phylogenetics in PCR protocols: a guide to methods and applications. (eds. Innis, M.A., D.H. Gelfand, J.J. Sninsky, and T.J. White) 315ā322 (Academic Press, Inc., 1990).
Acknowledgements
This research was supported by a grant from the Korean Ministry of Food and Drug Safety (15162MFDS053) and partially supported by a Korea University Grant. The authors also thank the School of Life Sciences and Biotechnology of Korea University for BK 21 PLUS and the Institute of Biomedical Science and Food Safety, Korea University Food Safety Hall, for providing equipment and facilities.
Author information
Authors and Affiliations
Contributions
M.S.R. designed the study; H.W.K., Y.S.S. and T.J.C. performed the experiments, H.W.K. and Y.S.S. analyzed and interpreted the data; H.W.K. wrote the manuscript; all authors command and approved the final manuscript.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisherās note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary information
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the articleās Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the articleās Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Kim, H.W., Seok, Y.S., Cho, T.J. et al. Risk factors influencing contamination of customized cosmetics made on-the-spot: Evidence from the national pilot project for public health. Sci Rep 10, 1561 (2020). https://doi.org/10.1038/s41598-020-57978-9
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41598-020-57978-9
This article is cited by
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.