Skip to main content

Thank you for visiting You are using a browser version with limited support for CSS. To obtain the best experience, we recommend you use a more up to date browser (or turn off compatibility mode in Internet Explorer). In the meantime, to ensure continued support, we are displaying the site without styles and JavaScript.

An Experimental Investigation on the Kinetics of Integrated Methane Recovery and CO2 Sequestration by Injection of Flue Gas into Permafrost Methane Hydrate Reservoirs


Large hydrate reservoirs in the Arctic regions could provide great potentials for recovery of methane and geological storage of CO2. In this study, injection of flue gas into permafrost gas hydrates reservoirs has been studied in order to evaluate its use in energy recovery and CO2 sequestration based on the premise that it could significantly lower costs relative to other technologies available today. We have carried out a series of real-time scale experiments under realistic conditions at temperatures between 261.2 and 284.2 K and at optimum pressures defined in our previous work, in order to characterize the kinetics of the process and evaluate efficiency. Results show that the kinetics of methane release from methane hydrate and CO2 extracted from flue gas strongly depend on hydrate reservoir temperatures. The experiment at 261.2 K yielded a capture of 81.9% CO2 present in the injected flue gas, and an increase in the CH4 concentration in the gas phase up to 60.7 mol%, 93.3 mol%, and 98.2 mol% at optimum pressures, after depressurizing the system to dissociate CH4 hydrate and after depressurizing the system to CO2 hydrate dissociation point, respectively. This is significantly better than the maximum efficiency reported in the literature for both CO2 sequestration and methane recovery using flue gas injection, demonstrating the economic feasibility of direct injection flue gas into hydrate reservoirs in permafrost for methane recovery and geological capture and storage of CO2. Finally, the thermal stability of stored CO2 was investigated by heating the system and it is concluded that presence of N2 in the injection gas provides another safety factor for the stored CO2 in case of temperature change.


The oceans, permafrost regions, and continental and marine sediments contain a huge volume of methane trapped in the form of gas hydrates1 which could be a potential energy source2 or CO2 storage sink3, depending upon human actions, with respect to energy policy and anthropogenic global warming. These ice-like hydrates which are non-stoichiometric inclusion compounds with hydrogen bonded water cages enclathrated light guest molecules without chemical bonds4, require suitable thermodynamic conditions including pressure, temperature, and surrounding liquid and gas compositions to remain stable. Various approaches were taken to shift the system conditions away from equilibrium in investigations of methane extraction from hydrate-bearing sediments. In comparison with potential methods such as thermal stimulation5, depressurization6, chemical inhibitor injection7, CO28,9 or CO2-mixed gases10 (e.g., flue gas) injection is more environmentally friendly because of the potential to capture CO2 simultaneously with methane recovery. Moreover, injection of CO2-mixed gases (mainly CO2 + N2) produced directly from power stations rather than pure CO2 is more economic owing to significant reductions in the total cost by avoidance of CO2 separation cost10,11,12 (See Fig. 1).

Figure 1

Graphical illustration of direct flue gas injection into hydrate-bearing sediments for geological carbon dioxide sequestration and methane recovery.

Coal-fired power plants represent a substantial proportion of global anthropogenic CO2 emissions which are the key contributors to global climate change13. The emission of CO2 in pulverized coal plants is caused by combustion of air and coal in a boiler to generate energy, producing flue gas with a low concentration of CO2 (~14%). Emission of flue gas from a typical 600 MWE power plant could be more than 500 m3 every second14. Accordingly, up-scaling post-combustion CO2 capture from power-plant flue gas through sustainable methods is gaining importance, to limiting CO2 emissions.

Previously, we presented initial results for injection of power-plant flue gas into gas hydrate reservoirs15 above freezing temperatures, defining a method10 to determine the optimum pressure for injection, where a more detailed review of the past literature can be found. In recent years, several12,16,17,18 investigations addressing various aspects of methane recovery by direct injection of flue gas have been reported, including limitations of CO2/CH416, effects of methane hydrate morphology and ratio of CO2/N2 in the injection gas17, the effect of sandstone permeability19, and efficiency of the method in the association with thermal stimulation12. Here, referring to the companion papers10,15 as a basis for our interpretations where necessary, we report new experimental results for the kinetics of optimized flue gas injection into methane hydrate reservoirs at sub-zero temperatures, covering both sub glacial and permafrost conditions, in addition to further discussing previous results. The efficiency of the method at sub-zero temperatures was also investigated as a considerable proportion of gas hydrate reservoirs are located underneath permafrost formations20,21,22. In addition, our previous experiments above freezing point showed significantly more favourable results for both CO2 storage and methane recovery at lower temperatures, also emphasizing the necessity of investigating the method efficiency under 0 °C. One of the objectives of this study was to investigate the efficiency of the method (i.e., methane recovery and CO2 storage percentages) in a realistic time scale and at hydrate reservoir conditions. The second key objective was to evaluate the impact of reservoir conditions on the kinetic efficiency, to examine potential methane reservoirs and identify a suitable site. Finally, the impact of global warming and natural temperature cycles on the stored CO2 was also investigated with the aim of understanding potential environmental hazards.

Results and Discussion

Kinetics of CO2 capture and CH4 recovery at optimum pressure

Figure 2a–f show the changes in gas phase composition with time and pressure obtained by GC after flue gas was injected. As shown in Fig. 2a,b methane concentration and CO2/(CO2 + N2) ratio changes with pressure in all experiments following a similar pattern. However there were differences in the rate of change, especially for those experiments conducted at temperatures below 0 °C. Initially, these values fluctuate slightly as a consequence of the initial pressure reduction, made in order to set the system at target pressure. Methane concentration in the gas phase increases continuously and the CO2/(CO2 + N2) reduces at the target pressure until the system reaches equilibrium, as is indicated in circles in Fig. 2a,b. Gas concentration changes with time since the pressure set was plotted at Fig. 2c–f. The main mechanism involved is the chemical potential shift of the system to higher pressure after flue gas injection (see EXPERIMENTAL SECTION), which forces the methane molecules vacate the clathrate cages allowing CO2 molecules to enter. This could either occur through CO2 replacement or full/part dissociation of the existing methane hydrates and formation of new CO2 or CO2-mixed hydrates with an accompanying release of hydrogen-bonded water molecules. Considering the experimental conditions, formation of CO2, CO2-N2, CO2-CH4, CO2-N2-CH4, and N2-CH4 is possible from a thermodynamic point of view as the pressure in all the experiments is well inside the aforementioned hydrate stability zones (see EXPERIMENTAL SECTION).

Figure 2

(a) CH4 concentration and (b) CO2/(CO2 + N2) evolution with pressure after flue gas was injected. CH4(c), CO2(d), N2(e), and CO2/(CO2 + N2) evolution with time after pressure was set to the optimum value.

Here, we define half-time (t1/2) as the time required for half of the increase in methane concentration to occur between when the pressure is set and the final equilibrium point. The defined half-time, t1/2 qualitatively reflects the economic viability of the proposed process for certain reservoirs, as for a reservoir with too high (t1/2) industrial scale application of the method would not be possible. t1/2 for all of the experiments was calculated to be no longer than 3 hours whereas the overall process could take up to 250 hours, indicating higher driving force due to higher chemical potential difference between gas and hydrate phase at the initial stage. A similar trend for the concentration of CO2 and N2 in the gaseous phase was observed (see Fig. 2d). At the later stage, increase of methane concentration in the gaseous phase dilutes CO2 and N2 concentration and consequently reduces the driving force for removing the CH4 molecules from the hydrate phase. It is also possible that replacement occurs rapidly on the surface of the methane hydrate, then the replacement rate decelerates considerably because of formation of a CO2-CH4 or CO2-N2 hydrate (CNH) layer on the surface, acting as a physical barrier. This layer prevents the CO2 molecules from entering into the interior of the methane hydrate, slowing down the replacement process. Thus, after forming a layer of CO2-CH4 or CNH, replacement slows down and a limited diffusion transport becomes the main mechanism for the replacement process. A similar explanation was presented in the literature23,24,25.

It is known that during formation of CO2-N2 mixed hydrate, CO2 goes to the larges cavities, whereas N2 will fill the small cavities26. To examine the selectivity of the CO2 over N2, CO2/(CO2 + N2) ratio with time after pressure set is presented in Fig. 2f showing a decrease with time, indicating stronger selectivity of the CO2 over N2 in all the experiments owing to relatively higher27,28 stability of CO2 than N2 at the hydrate phase. This shows relatively higher occupancy of large cavities than small cavities. These results are in agreement with previous studies15,29.

Methane recovery during depressurisation

As mentioned in the previous section the system was depressurized stepwise every 24 hours after reaching equilibrium state at the target pressure. As shown in Fig. 2a, as the system pressure reduces, CH4 comes out of the hydrate phase and the percentage of CH4 in the gas phase increases until reaching the CO2 HSZ, after which CH4 started to decrease because of dissociation of the CO2 rich clathrates. This is true apart from Experiment 7, where CH4 in the gas phase increases after initial drop. This can be attributed to the fact that in this experiment the pressure of the CO2 hydrate dissociation is higher than that of CH4 hydrate (see EXPERIMENTAL SECTION), thus, CO2-rich hydrates dissociate first, followed by dissociation of CH4-rich hydrate. Regarding the CO2/(CO2 + N2) ratio during step-wise depressurization, Fig. 2b shows upward trends until passing CO2 HSZ. This could be justified by the fact that, during depressurization N2-rich gas was removed, and consequently overall CO2/(CO2 + N2) ratio was increased as a consequence of dissociation of those hydrates with more CO2 than N2, and after passing CO2 HSZ this ratio reached to its maximum amount because of the dissociation of CO2-rich hydrate. The maximum peak of this graph could be used as an indicator of efficiency of the CO2 capture at the optimum pressure, in that more CO2 stored at the optimum pressure means more CO2 trapped in hydrate phase so that this peak will be higher because of dissociation of more CO2 hydrate.

Effect of hydrate reservoir temperature on CO2 sequestration

Both methane recovery and CO2 storage strongly depend on hydrate reservoir temperature. The extent of changes in gas compositions at lower temperatures are typically larger than those at higher temperatures, as would be expected due to the stronger selectivity of CO2 to N2 and CH4 in hydrate phase at lower temperature that dominates the molecular exchange between the gas and hydrate phase. In addition, the experimental pressures for lower temperatures were also lower than those for higher temperatures (see EXPERIMENTAL SECTION) due to the fact that hydrate dissociation points have lower pressures at lower temperatures. As a result, the compression cost for the reservoir with lower temperatures could be considerably lower. Although, lowering the temperature increases the time required for the process after (t1/2), graphs for both methane recovery and CO2 storage at negative temperatures show better efficiency in terms of time than positive ones at any times. With this in mind, the experiment at 261.2 K has the maximum efficiency for both methane recovery and CO2 storage, indicating that the more CO2 storage the more methane production. To be able to quantitatively analyse the results, C-value, is defined and referred to as the molar ratio of stored CO2 in the hydrate phase after reaching equilibrium at target pressure to the injected total CO2. C-value is calculated for each experiment using our in house thermodynamic modelling software30 and is plotted in Fig. 3 together with CH4 concentration in gas phase at target pressure after reaching equilibrium, before passing CH4 HSZ, and before passing CO2 HSZ. As can be seen 81.9% of the injected CO2 present in the flue gas was stored in the hydrate phase at −12 °C, and the molar percentage of CH4 in the gas phase reached 60.65, 93.34, 98.18 at the optimum pressure, and the boundary of CH4 HSZ and CO2 HSZ, respectively. For the experiments at higher temperatures, however, the figures in Fig. 3 decreased and reached a minimum in Experiment 7.

Figure 3

Calculated C-value, and CH4 concentration at the optimum pressures after the system reached to the equilibrium and CH4 concentration just before the system passed outside the CH4 HSZ and CO2 HSZ.

Response of CO2-mixed hydrates to temperature rise

Thermal stability of the stored CO2 is also a major issue for the long-term stability of the CO2 underground because the temperature cycle in the storage environment may change the gas hydrates. This was the main reason for the investigation into the dissociation of hydrates in Experiment 2 R using thermal stimulation in addition to investigating the repeatability of the procedure. As can clearly be seen in Fig. 2, before depressurization Experiments 2 and 2 R showed very repeatable results. As mentioned before for Experiment 2 R, the temperature of the system was increased to investigate the dissociation behaviour of the previously formed hydrates at the optimum pressure. The gas composition evolution during dissociation was analysed by GC and the compositional results are plotted versus pressure in Fig. 4. As a result of temperature rise the gas phase starts to expand and the formed hydrates start to dissociate, which in turn leads to changes in the composition of the gas phase. As shown, initially the concentration of N2 increases whereas the concentrations of CH4, and CO2 and CO2/(CO2 + N2) reduces. The reduction of CO2/(CO2 + N2) shows that initially those hydrates with relatively more N2 start to decompose. This is a positive sign as it shows N2 not only acts as promoting agent for CO2/CH4 replacement but also provides another safety factor for retention of the CO2-rich hydrates during temperature rise. We have previously showed31 the role of N2 for providing safety factor for thermal stability of stored CO2 by hydrate formation using flue gas in absence of initial methane hydrate in place. However, this is the first mention of the potential safety role of N2 for methane recovery by flue gas injection. After this phase, there is a sharp change in the composition of the gas phase before reaching an almost stable composition. In this period, the gas hydrates are quickly dissociating and the released gas is going to the gas phase, thus, the absence of changes in the gas phase implies that the composition of the gas phase in this period is similar to the composition of those hydrates which are dissociating. After this phase, there is another sharp increase followed by a slight decrease in CO2 concentration and CO2/(CO2 + N2) ratio before the system reaches equilibrium. This rise shows that hydrates with higher CO2 content dissociate after dissociation of hydrates with lower CO2 content. The possible explanation for the slight decrease in the concentration of the CO2 and CO2/(CO2 + N2) ratio is the higher solubility of CO232 compared to N2 and CH4.

Figure 4

Gas compositional changes with pressure after cryostat temperature was set to 294.15 K at Experiment 2 R.

Experimental Section


Deionized water (total organic carbon < 5 ppb) from an ELGA DV 25 Integral Water Purification was used for wetting sands, and cleaning of the experimental setup. The following gases from BOC Limited were used in the experiments: CO2 (99.995 vol %), N2 (99.995 vol %), and CH4 (99.995 vol %). Well-characterized sands from Fife, Scotland were used for simulating mesoporous hydrate reservoirs. As described in our previous work31, the Sand mainly consists of quartz which has very small gas adsorption capacity33 compared to gas inclusion in clathrate hydrate and water. Accordingly, the effect of gas adsorption to the sand was neglected in this study.

A high-pressure cylindrical cell setup was employed in all the experiments as shown in Fig. 5. The cell body is made of 316 stainless steel. The geometric area exposed to the hydrate-bearing sediments has been placed between a fixed top cap and a bottom cap. A movable piston is mounted above the bottom cap to simulate the overburden pressure, moving up and down by withdrawal or injection of hydraulic fluid behind the piston. Thus, the reservoir is not in direct contact with hydraulic fluid. Hydraulic fluid injection/removal was performed using a dual-cylinder Quizix pump (SP-5200, Chandler Engineering) for maintaining the pressure or a hand pump for achieving initial compaction pressure. A linear variable differential transformer (LVDT) is mounted on the bottom cap to measure the piston movement; therefore, the reservoir volume could be calculated at any stage. For controlling the temperature during experiments, the cell is fitted in an aluminium jacket, which is cooled/heated as a whole by circulation of the cooling fluid (water/monoethylene glycol solution from a cryostat (Julabo MA-4). The cooling jacket is wrapped with an insulation layer to reduce the heat transfer from the surrounding environment and the temperature gradient. Two QUARTZDYNE pressure transducers (model QS30K-B, Quartzdyne Inc., U.S.A.)(+/− 0.005 MPa) and a Platinum Resistance Thermometer (PRT) (+/− 0.1 K) were used to measure the cell and overburden pressures, and the cell temperature, respectively. The temperature, all pressures (including pore pressure, overburden pressure, and pump pressure), and the LVDT displacement were monitored by a feedback system of the setup (LabVIEW software from National Instruments). All gas injections, withdrawals, and samplings, were achieved using valves allocated at the top, bottom, and two sides. Finally, a Gas Chromatograph (GC) (Varian 3600, Agilent Technologies) was used to analyse the composition of gas samples for monitoring the evolution in gas composition within the system.

Figure 5

Schematic of the high-pressure cell setup.


In a typical test, 1076.6 g of the sand was partially saturated with 155.6 g deionized water. The wetted sediment was then loaded into the cell, and the system was evacuated to soak the remained air out. Following evacuation, the piston level was adjusted to compact the system with 3.45 MPa overburden pressure for at least a day. Prior to injection of the test gas, the system temperature was set to 298.15 K (to ensure there was no hydrate formation possibility in the working pressure range). A certain amount of CH4 gas was then added through the valves from top and bottom until the desired initial pressure is reached. Subsequently, the system temperature was set to 273.35 K (just above freezing point of water) to form hydrate without appearance of ice in the system. The system pressure reduced as temperature declined. Since water was exposed to the high pressure CH4 well inside the HSZ at this point, hydrate formation started, reducing the system pressure till the equilibrium point was reached at the experimental temperature. The onset of hydrate formation appeared at the point where there was a clear change in slope of the pressure profile during cooling. The hydrate formation period could take more than a week because there was no mixing in the system. Although some conventional temperature cycling methods (e.g. Stern’s method34) could be used to accelerate the hydrate formation, the cryostat temperature remained stable to preserve the sediment structure built in an entirely controlled method. Hydrate formation/growth continued until a stable pressure profile could be observed, confirming completion of hydrate formation.

After completion of hydrate formation, the first test was conducted at this hydrate formation temperature while for the other experiments, the bath temperature was re-set to the target temperature. At this point, hydrate, gas, water, and ice saturation were calculated as shown in Table 1. The same formulation as our previous work35 was used for the calculation of the saturation. For purging the remaining methane gas and reducing the proportion of remaining free methane in the gas phase without dissociation of methane hydrate, flue gas composed of 85.4 mol % N2 and 14.6 mol % CO2 was injected to the cell at a pressure approximately 10 times the equilibrium pressure of methane hydrate at the target temperature after hydrate formation. Then gas was slowly released from the system until the system was depressurized to 0.7 MPa above flue gas hydrate phase boundary immediately to avoid or minimise formation of flue gas hydrates. Once the methane concentration was less than 15% during the purging process, the injection port was closed and the system pressure was reduced to a specified optimum point by moving the piston backward. These optimum pressures were determined by the method described in the companion paper to this work10. At this step, pressure was maintained using a dual-cylinder Quizix pump and samples from the gas phase were collected at pre-determined time intervals to be analysed using a GC. After reaching the equilibrium condition (no change in gas composition for 3 days), the system was depressurized in a stepwise manner to recover the remaining methane. Experiment 2 R was conducted to check the repeatability of the experiments, which followed the same procedure as Experiment 2. However, after reaching equilibrium state at the target pressure, instead of depressurization, the system was heated to room temperature (294.15 K) to investigate dissociation of the formed hydrates.

Table 1 Hydrate, gas, water, and Ice + quasi liquid saturation after methane hydrate formation and before flue gas injection.

As we have previously defined the effect of pressure on the CO2 storage and methane recovery, and have indicated that there is an optimum pressure10 at each temperature using simulated bulk conditions, it is necessary to determine the efficiency of the method at real world conditions. Furthermore, it is also important to characterize the kinetics of the process in such conditions as mass and heat transfer is strongly constrained by mesoporous media. I addition, the effect of ice on the kinetics of the process was investigated to cover conditions of encountered in methane hydrate reservoirs located in high-latitude regions of the Earth. Hence, the experiments were designed to fundamentally understand the kinetics and efficiency of methane recovery and CO2 storage by injection of flue gas into hydrate-bearing sediments at the previously defined optimum pressures. The procedure was in all cases as described above. The experimental pressure/temperature conditions together with hydrate stability zones of N2, CH4, CO2, flue gas, and different combinations of flue gas/CH4 are provided in Fig. 6. The green dots show the optimum conditions at which the system was kept at nearly constant pressure. According to Fig. 6, the experiments sufficiently cover a temperature range for permafrost, sub permafrost, subglacial, and subsea sediments36.

Figure 6

The predicted hydrate stability zones of CO2, N2, CH4 and their mixtures and the experimental conditions.


  1. 1.

    Kvenvolden, K. A. & Lorenson, T. D. The Global Occurrence of Natural Gas Hydrate. In Geophysical Monograph Series 124, 3–18 (2013).

    Google Scholar 

  2. 2.

    Yang, S. H. B., Linga, P., Chong, Z. R., Babu, P. & Li, X.-S. Review of natural gas hydrates as an energy resource: Prospects and challenges. Appl. Energy 162, 1633–1652 (2015).

    Google Scholar 

  3. 3.

    House, K. Z., Schrag, D. P., Harvey, C. F. & Lackner, K. S. Permanent carbon dioxide storage in deep-sea sediments. Proc. Natl. Acad. Sci. 103, 12291–12295 (2006).

    ADS  CAS  Article  Google Scholar 

  4. 4.

    Sloan, E. D. Fundamental principles and applications of natural gas hydrates. Nature 426, 353–359 (2003).

    ADS  CAS  Article  Google Scholar 

  5. 5.

    Yin, Z., Moridis, G., Chong, Z. R., Tan, H. K. & Linga, P. Numerical Analysis of Experiments on Thermally Induced Dissociation of Methane Hydrates in Porous Media. Ind. Eng. Chem. Res. 57, 5776–5791 (2018).

    CAS  Article  Google Scholar 

  6. 6.

    Terzariol, M., Goldsztein, G. & Santamarina, J. C. Maximum recoverable gas from hydrate bearing sediments by depressurization. Energy 141, 1622–1628 (2017).

    CAS  Article  Google Scholar 

  7. 7.

    Li, G. et al. Experimental Investigation into the Production Behavior of Methane Hydrate under Methanol Injection in Quartz Sand. Energy and Fuels 31, 5411–5418 (2017).

    CAS  Article  Google Scholar 

  8. 8.

    Merey, S., Al-Raoush, R. I., Jung, J. & Alshibli, K. A. Comprehensive literature review on CH4-CO2 replacement in microscale porous media. J. Pet. Sci. Eng. 171, 48–62 (2018).

    CAS  Article  Google Scholar 

  9. 9.

    Chen, Y. et al. Experimental investigation of different factors influencing the replacement efficiency of CO2 for methane hydrate. Appl. Energy 228, 309–316 (2018).

    CAS  Article  Google Scholar 

  10. 10.

    Hassanpouryouzband, A. et al. CO2 Capture by Injection of Flue Gas or CO2-N2 Mixtures into Hydrate Reservoirs: Dependence of CO2 Capture Efficiency on Gas Hydrate Reservoir Conditions. Environ. Sci. Technol. 52, 4324–4330 (2018).

    ADS  CAS  Article  Google Scholar 

  11. 11.

    Hassanpouryouzband, A. et al. Insights into CO2 Capture by Flue Gas Hydrate Formation: Gas Composition Evolution in Systems Containing Gas Hydrates and Gas Mixtures at Stable Pressures. ACS Sustain. Chem. Eng. 6, 5732–5736 (2018).

    CAS  Article  Google Scholar 

  12. 12.

    Tupsakhare, S. S. & Castaldi, M. J. Efficiency enhancements in methane recovery from natural gas hydrates using injection of CO2/N2 gas mixture simulating in-situ combustion. Appl. Energy 236, 825–836 (2019).

    CAS  Article  Google Scholar 

  13. 13.

    IPCC. Climate Change 2013 - The Physical Science Basis. Climate Change 2013 - The Physical Science Basis (IPCC, 2014),

    Google Scholar 

  14. 14.

    Merkel, T. C., Lin, H., Wei, X. & Baker, R. Power plant post-combustion carbon dioxide capture: An opportunity for membranes. J. Memb. Sci. 359, 126–139 (2010).

    CAS  Article  Google Scholar 

  15. 15.

    Yang, J. et al. Flue gas injection into gas hydrate reservoirs for methane recovery and carbon dioxide sequestration. Energy Convers. Manag. 136, 431–438 (2017).

    CAS  Article  Google Scholar 

  16. 16.

    Peter, E., Messah, M. & Chau, J. Gas Recovery Through the Injection of Carbon Dioxide or Concentrated Flue Gas in a Natural Gas Hydrate Reservoir. in Offshore Technology Conference Asia, (Offshore Technology Conference, 2018).

  17. 17.

    Li, B. et al. An experimental study on gas production from fracture-filled hydrate by CO2 and CO2/N2 replacement. Energy Convers. Manag. 165, 738–747 (2018).

    CAS  Article  Google Scholar 

  18. 18.

    Mu, L. & Von Solms, N. Experimental Study on Methane Production from Hydrate-Bearing Sandstone by Flue Gas Swapping. Energy and Fuels 32, 8167–8174 (2018).

    CAS  Article  Google Scholar 

  19. 19.

    Okwananke, A. et al. Methane recovery from gas hydrate-bearing sediments: An experimental study on the gas permeation characteristics under varying pressure. J. Pet. Sci. Eng. 180, 435–444 (2019).

    CAS  Article  Google Scholar 

  20. 20.

    Wang, X. et al. Reservoir volume of gas hydrate stability zones in permafrost regions of China. Appl. Energy 225, 486–500 (2018).

    Article  Google Scholar 

  21. 21.

    Lin, Z., Pan, H., Fang, H., Gao, W. & Liu, D. High-altitude well log evaluation of a permafrost gas hydrate reservoir in the Muli area of Qinghai, China. Sci. Rep. 8, 12596 (2018).

    ADS  Article  Google Scholar 

  22. 22.

    Boswell, R. et al. Permafrost-associated natural gas hydrate occurrences on the Alaska North Slope. Mar. Pet. Geol. 28, 279–294 (2009).

    Google Scholar 

  23. 23.

    Geng, C. Y., Wen, H. & Zhou, H. Molecular simulation of the potential of methane reoccupation during the replacement of methane hydrate by CO2. J. Phys. Chem. A 113, 5463–5469 (2009).

    CAS  Article  Google Scholar 

  24. 24.

    Bai, D., Zhang, X., Chen, G. & Wang, W. Replacement mechanism of methane hydrate with carbon dioxide from microsecond molecular dynamics simulations. Energy Environ. Sci. 5, 7033–7041 (2012).

    CAS  Article  Google Scholar 

  25. 25.

    Lee, B. R., Koh, C. A. & Sum, A. K. Quantitative measurement and mechanisms for CH4 production from hydrates with the injection of liquid CO2. Phys. Chem. Chem. Phys. 16, 14922–14927 (2014).

    CAS  Article  Google Scholar 

  26. 26.

    Dornan, P., Alavi, S. & Woo, T. K. Free energies of carbon dioxide sequestration and methane recovery in clathrate hydrates. J. Chem. Phys. 127, 124510–124700 (2007).

    ADS  Article  Google Scholar 

  27. 27.

    Petuya, C., Damay, F., Chazallon, B., Bruneel, J. L. & Desmedt, A. Guest Partitioning and Metastability of the Nitrogen Gas Hydrate. J. Phys. Chem. C 122, 566–573 (2018).

    CAS  Article  Google Scholar 

  28. 28.

    Chazallon, B. & Pirim, C. Selectivity and CO2 capture efficiency in CO2-N2 clathrate hydrates investigated by in-situ Raman spectroscopy. Chem. Eng. J. 342, 171–183 (2018).

    CAS  Article  Google Scholar 

  29. 29.

    Koh, D. Y. et al. Recovery of methane from gas hydrates intercalated within natural sediments using CO2 and a CO2/N2 gas mixture. ChemSusChem 5, 1443–1448 (2012).

    CAS  Article  Google Scholar 

  30. 30.

    Mahabadian, M. A., Chapoy, A., Burgass, R. & Tohidi, B. Development of a multiphase flash in presence of hydrates: Experimental measurements and validation with the CPA equation of state. Fluid Phase Equilib. 414, 117–132 (2016).

    CAS  Article  Google Scholar 

  31. 31.

    Hassanpouryouzband, A. et al. Geological CO2 Capture and Storage with Flue Gas Hydrate Formation in Frozen and Unfrozen Sediments: Method Development, Real Time-Scale Kinetic Characteristics, Efficiency, and Clathrate Structural Transition. ACS Sustain. Chem. Eng. (2019).

    Article  Google Scholar 

  32. 32.

    Hassanpouryouzband, A. et al. Solubility of Flue Gas or Carbon Dioxide-Nitrogen Gas Mixtures in Water and Aqueous Solutions of Salts: Experimental Measurement and Thermodynamic Modeling. Ind. Eng. Chem. Res. 58, 3377–3394 (2019).

    CAS  Article  Google Scholar 

  33. 33.

    Stahl, W., Faber, E., Carey, B. D. & Kirksey, D. L. Near-surface evidence of migration of natural gas from deep reservoirs and source rocks. Am. Assoc. Pet. Geol. Bull. 65, 1543–1550 (1981).

    CAS  Google Scholar 

  34. 34.

    Stern, L. A., Kirby, S. H. & Durham, W. B. Peculiarities of methane clathrate hydrate formation and solid-state deformation, including possible superheating of water ice. Science (80−.). 273, 1843–1848 (1996).

    ADS  CAS  Article  Google Scholar 

  35. 35.

    Yang, J. et al. Gas hydrates in permafrost: Distinctive effect of gas hydrates and ice on the geomechanical properties of simulated hydrate‐bearing permafrost sediments. J. Geophys. Res. Solid Earth 124, 2551–2563 (2019).

    ADS  CAS  Article  Google Scholar 

  36. 36.

    Portnov, A., Vadakkepuliyambatta, S., Mienert, J. & Hubbard, A. Ice-sheet-driven methane storage and release in the Arctic. Nat. Commun. 7 (2016).

Download references


This work was financially supported by the Skolkovo Institute of Science and Technology, Russia, which is acknowledged gratefully. The experiments were conducted at the Centre for Hydrate Research, Institute of Petroleum Engineering, Heriot-Watt University, Edinburgh, United Kingdom.

Author information




A.H., J.Y. and A.O. conceived the idea presented in this publication; A.H., A.O. Performed laboratory experiments and analysed the data; B.T. and J.Y. supervised the research; A.H. and J.Y. Wrote the manuscript. R.B., B.T., E.C., V.I. and B.B. discussed the results and contributed to the final manuscript.

Corresponding author

Correspondence to Jinhai Yang.

Ethics declarations

Competing interests

The authors declare no competing interests.

Additional information

Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit

Reprints and Permissions

About this article

Verify currency and authenticity via CrossMark

Cite this article

Hassanpouryouzband, A., Yang, J., Okwananke, A. et al. An Experimental Investigation on the Kinetics of Integrated Methane Recovery and CO2 Sequestration by Injection of Flue Gas into Permafrost Methane Hydrate Reservoirs. Sci Rep 9, 16206 (2019).

Download citation

Further reading


By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.


Quick links

Nature Briefing

Sign up for the Nature Briefing newsletter — what matters in science, free to your inbox daily.

Get the most important science stories of the day, free in your inbox. Sign up for Nature Briefing